AWS5504 GaAs IC Negative Control SPDT Reflective Switch DC-2.0 GHz Data Sheet - Rev 2.1 FEATURES • • • • • • High Linearity (IP3 48 dBm @ 0.9 GHz) Low Insertion Loss (0.4 dB @ 0.9 GHz) 2.75 V to -3.5 to +2.75 operation Low DC Power Consumption Ultra Miniature SOT-26 Package High Isolation APPLICATIONS • • • S14 SOT-26 6 Pin Plastic Package Transmit/receive switch Diversity switching Antenna selection DESCRIPTION The AWS5504 is a Single Pole Double Throw (SPDT) GaAs MMIC switch assembled in a SOT-6 plastic package. The AWS5504 is designed for analog and digital applications that require low insertion loss, high linearity, and small size. The switch can be controlled with positive, negative, or a combination of both voltages. Table 1: Pin Description Vs C1 10KΩ 5 4 C2 V1 C3 3 RFOUT 2 (J3) 2 GND 6 1 RFOUT 1 (J2) RFI N (J1) PIN NAME 1 RF OUT 1 (J2) RF port can be used as an input or as an output. 2 GND Ground connection. Keep as short as possible. 3 RF OUT 2 (J3) RF port can be used as an input or an ouput. 4 V2 Control Voltage 2, Low 0V , High 3V to 5V 5 RF IN (J1)/Vs 6 V1 V2 DC block capacitors C 1, 2, 3 must be supplied externally. C1, 2 , 3 = 100 pF for operation >500 MHz Figure 1: Pin Out Diagram 08/2001 DESCRIPTION RF common port and bias voltage for positive control (3V to 5V). Control Voltage 1, Low 0V , High 3V to 5V AWS5504 ELECTRICAL CHARACTERISTICS Table 2: Absolute Maximum Ratings PARAMETER MIN MAX UNIT - 6 W Control Voltage -0.2 +8 V Operating Temperature -40 +85 °C Storage Temperature -65 +150 °C - 25 °C/W RF Input Power > 900 MHz, 0/-5 V Control Θ JC Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Table 3: Operating Ranges at 25° C (0, +5V) PARAMETER Switching Characteritics 5 Intermodulation Intercept Point (IP3) CONDITION FREQUENCY MIN TYP MAX UNIT Rise, Fall (10/90% or 90/10% RF) On, Off (50% CTL to 90%/10% RF) Video Feedthru - - 60 100 50 - ns ns mV For Two-tone Input Power +10 dBm 0.9 GHz - +55 - dBm 0.9 GHz - +38 - dBm Input Power for 1dB Compression Control Voltage V LOW = 0 to 0.2 V @ 20 uA Max V HIGH = +3 V @ 100 uA Max to +5 V @ 200 uA Max V S = V HIGH + 0.2V The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Notes: 1. All measurements made in a 50 ohm system, unless other specified. 2. DC = 300 kHz. 3. Insertion loss changes by 0.003 dB/°C. 4. Insertion loss state. 5. Video feedthru measured with 1 ns rise time pulse and 500 MHz bandwidth. 2 Data Sheet - Rev 2.1 08/2001 AWS5504 Table 4: Electrical Specifications at 25 °C (0, +5V) FREQUENCY 2 MIN TYP MAX UNIT DC - 0.5 GHz DC - 1.0 GHz DC - 2.0 GHz - 0.3 0.4 1.0 0.4 0.6 1.2 dB Isolation DC - 0.5 GHz DC - 1.0 GHz DC - 2.0 GHz 20 15 8 23 17 10 - dB VSWR 4 DC - 1.0 GHz DC - 2.0 GHz - 1.3:1 1.3:1 1.4:1 1.8:1 dB PARAMETER Insertion Loss 1 3 Notes: 1. All measurements made in a 50 Ω system, unless other specified. 2. DC= 300 kHz 3. Insertion loss changes by 0.003 dB/°C. 4. Insertion loss state. 5. Video feedthru measured with 1 nx rise time pulse and 500 MHz bandwidth. Table 5: Truth Table V1 V2 J1 - J2 J1 - J3 0 VHigh Isolation Insertion Loss VHigh 0 Insertion Loss Isolation VHigh = +3 to +5 V (VS = Vhigh + 0.2 V) Data Sheet - Rev 2.1 08/2001 3 AWS5504 Figure 2: Test Circuit Schematic 4 Data Sheet - Rev 2.1 08/2001 AWS5504 PACKAGE OUTLINE θ SYMBOLS A A1 A2 b C D E e H L θ1 DIMENSIONS IN MILLIMETERS DIMENSIONS IN INCHES MIN MAX 1.00 1.30 0.00 0.10 0.70 0.90 0.35 0.50 0.10 0.25 2.70 3.10 1.40 1.80 1.90(TYP) 2.60 3.00 0.37 −−− 1° 9° MIN MAX 0.039 0.051 0.00 0.004 0.027 0.035 0.014 0.020 0.004 0.010 0.106 0.122 0.055 0.071 0.075(TYP) 0.102 0.118 0.015 −−− 1° 9° NOTE 1. PACKAGE BODY SIZES EXCLUDE MOLD FLASH AND GATE BURRS 2. DIMENSION L IS MEASURED IN GAGE PLANE 3. COPLANARITY : 0.1000 mm 4. TOLERANCE ±0.1000 mm(4 mil) UNLESS OTHERWISE SPECIFIED NOTES: 1. Package body sizes exclude mold flash and gate burrs. 2. Dimension L is measured in gage plane 3. Coplanarity: 0.1000 mm 4. Tolerance + 0.1000 mm (4 mil) unless otherwise specified. Figure 3: Package Outline Data Sheet - Rev 2.1 08/2001 5 AWS5504 NOTES 6 Data Sheet - Rev 2.1 08/2001 AWS5504 NOTES Data Sheet - Rev 2.1 08/2001 7 AWS5504 ORDERING INFORMATION ORDER NUMBER PACKAGE DESCRIPTION AWS5504S14 S14 COMPONENT PACKAGING 6 Pin Plastic Package ANADIGICS, Inc. 35 Technology Drive Warren, New Jersey 07059 Tel: (908) 668-5000 Fax: (908) 668-5132 http://www.anadigics.com [email protected] IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. WARNING ANADIGICS products are not intended for use in life support appliances, devices, or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. Data Sheet - Rev 2.1 08/2001 8