APA2020A Stereo 2-W Audio Power Amplifier Features General Description • • • • • • The APA2020A is a stereo bridge-tied audio power amplifier in various 24-pin power packages , including SOP , TSSOP-P. When connecting to a 5V voltage supply , the APA2020A is capable of delivering 1.8W/1.2W of continuous RMS power per channel into 4Ω/8Ω loads with less than 1% THD+N , respectively. The APA2020A simplifies design and frees up board space for other features . • • • Low Supply Current , IDD= 8mA at Stereo BTL Low Shutdown Current , IDD= 0.5µA Depop Circuitry Integrated Low Supply Voltage Thermal Shutdown Circuitry Integrated Output Power at 1% THD+N , VDD=5V - 1.8 W/Ch (typ) into a 4 Ω Load - 1.2 W/Ch (typ) into a 8 Ω Load Bridge-Tied Load (BTL) or Single-Ended (SE) Modes Operation Various 24-Pin Power Packages Available SOP , TSSOP-P High Supply Voltage Ripple Rejection The APA2020A also served well in low-voltage applications , which provides 800-mW per channel into 4Ω loads with a 3.3V supply voltage . Both of the depop circuitry and the thermal shutdown protection circuitry are integrated in the APA2020A , that reduces pops and clicks noise during power up and when using the shutdown or mute modes and protects the chip from being destroyed by over-temperature failure. To simplify the audio system design in notebook computer applications , the APA2020A combines a stereo bridge-tied loads (BTL) mode for speaker drive and a stereo single-end (SE) mode for headphone drive into a single chip , where both modes are easily switched by the SE/BTL input control pin signal . For power sensitive applications , the APA2020A also features a shutdown function which keeps the supply current only 0.5 µA (typ) . Applications • Stereo Audio Power Amplifier for Notebook Computer Ordering Information APA2020A Package Code K : SOP Handling Code R : TSSOP-P * Temp. Range I: - 40 to 85 °C Temp. Range Package Code Handling Code TU : Tube TY : Tray TR : Tape & Reel * TSSOP-P is a standard TSSOP package with a thermal pad exposure on the bottom of the package. ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. Copyright ANPEC Electronics Corp. Rev. A.5 - July., 2002 1 www.anpec.com.tw APA2020A Block Diagram MUX MUX MUX SE/BTL Absolute Maximum Ratings (Over operating free-air temperature range unless otherwise noted.) Symbol Parameter V CC Supply Voltage TA TJ TSTG TS V ESD Operating Ambient Temperature Range Maximum Junction Temperature Storage Temperature Range Soldering Temperature,10 seconds Electrostatic Discharge Rating Unit 6 V -40 to 85 150 -65 to +150 300 -3000 to 3000 *1 -200 to 200 *2 °C °C °C °C V Note: 1. Human body model : C=100pF , R=1500Ω , 3 positive pulses plus 3 negative pulses 2. Machine model : C=200pF , L=0.5mH , R=0Ω , 3 positive pulses plus 3 negative pulses Copyright ANPEC Electronics Corp. Rev. A.5 - July., 2002 2 www.anpec.com.tw APA2020A Recommended Operating Conditions Supply Voltage, VDD VDD=5V, 4-Ω stereo BTL drive, Operating free-air 250mW/Ch average power, with proper PCB temperature, TA design VDD=5V, 2 W/Ch average power, 3-Ω stereo BTL drive, with proper PCB design and 300 CFM forced-air cooling VDD=5 V Common mode input voltage, VICM VDD=3.3V Min. Typ. Max. Unit 3 5 5.5 V -20 85 °C -20 85 1.25 4.5 1.25 2.7 V Electrical Characteristics (Cont.) AC Operating Characteristics , VDD= 5V , TA= 25°C , RL= 4Ω (unless otherwise noted) Symbol P(out) Test Condition APA2020A Min. Typ. Max. THD = 10% , BTL , RL=4Ω 2.3 RL=8Ω 1.5 Parameter Output power (each channel ) see Note 1 THD = 1% , BTL , R L=4Ω 1.8 RL=8Ω 1.2 THD = 10% , SE , RL=4Ω 650 RL=8Ω 400 THD = 1% , SE , RL=4Ω 500 R L=8Ω 320 THD = 0.5% , SE , RL=32 Ω THD + N Total harmonic distortion plus PO = 1.6W , BTL , RL=4Ω noise PO = 1W , BTL , R L=8Ω PO = 78mW , SE ,R L=32Ω V1 = 1V , RL=4Ω , G = 1 BOM mW 300 150 20 m% 10 G = 10 , THD < 1% Phase margin RL = 4Ω , BTL 72 RL = 4Ω , Open Load 71 RL = 4Ω , SE 52 3 W 90 Maximum output power bandwidth Copyright ANPEC Electronics Corp. Rev. A.5 - July., 2002 Unit >20 KHz ° www.anpec.com.tw APA2020A Electrical Characteristics (Cont.) AC Operating Characteristics , VDD= 5V , TA= 25°C , RL= 4Ω (unless otherwise noted) Symbol PSRR ZI Parameter Power supply ripple rejection f =100 Hz APA2020A Min. Typ. Max. 80 Unit dB Mute attenuation 85 dB Channel-to-channel output separation 85 dB Line HP input separation 75 dB BTL attenuation in SE mode 80 dB Input impedance 2 MΩ 90 dB 80 µV(rms) Signal-to-noise ratio Vn Test Condition Po = 500 mW , BTL Output noise voltage Notes 1 : Output power is meaured at the output teminals of the IC at 1 KHz. AC Operating Characteristics , VDD= 3.3V , TA= 25°C , RL= 4Ω (unless otherwise noted) APA2020A Symbol Parameter Test Condition Min. Typ. Max. P(out) Output power (each channel ) 1 THD = 10% , BTL , R L=4Ω see Note 2 0.6 RL=8Ω THD = 1% , BTL , RL=4Ω 0.8 RL=8Ω 0.5 THD = 10% , SE , RL=4Ω 290 RL=8Ω 180 THD = 1% , SE , RL=4Ω 230 RL=8Ω 140 THD = 0.5% , SE , RL=32 Ω THD + N Total harmonic distortion plus PO = 1.6W , BTL , R L=4Ω noise PO = 1W , BTL , R L=8Ω PO = 78mW , SE ,RL=32Ω V1 = 1V , R L=4Ω , G = 1 BOM mW 270 150 20 m% 10 G = 10 , THD < 1% Phase margin RL = 4Ω , BTL 92 RL = 4Ω , Open Load 70 RL = 4Ω , SE 57 4 W 43 Maximum output power bandwidth Copyright ANPEC Electronics Corp. Rev. A.5 - July., 2002 Unit >20 KHz ° www.anpec.com.tw APA2020A Electrical Characteristics (Cont.) AC Operating Characteristics , VDD= 3.3V , TA= 25°C , RL= 4Ω (unless otherwise noted) Symbol PSRR Parameter Power supply ripple rejection Test Condition f =100 Hz APA2020A Min. Typ. Max. 70 Mute attenuation dB 85 dB Line HP input separation 75 dB BTL attenuation in SE mode 80 dB Input impedance 2 MΩ 90 dB 50 µV(rms) APA2020A Typ. Max. 8 11 4 6.5 7 9 3.5 5.6 5 25 Unit Signal-to-noise ratio Vn dB 85 Channel-to-channel output separation ZI Unit f =1 KHz Po = 500 mW , BTL Output noise voltage Notes 2 : Output power is meaured at the output teminals of the IC at 1 KHz. DC Electrical Characteristic , TA=25 °C Symbol IDD V O (DIFF) IDD(MUTE) ISD Parameter Supply Current Test Conditions V DD = 5V Stereo BTL Stereo SE V DD = 3.3 V Stereo BTL Stereo SE V DD =5V, Gain = 2, see Note3 DC Differential Output Voltage Supply Current in Mute Mode V DD = 5V IDD in Shutdown V DD = 5V 8 0.5 11 5 mA mA mA mA mV mA µA Note 3 : at 3V<VDD<5V , the DC output voltage is approximately VDD / 2. Copyright ANPEC Electronics Corp. Rev. A.5 - July., 2002 5 www.anpec.com.tw APA2020A Pin Description GND/HS 1 24 TJ LOUT+ LLINEIN 2 23 22 21 LHPIN LBYPASS LVDD SHUTDOWN 5 8 17 MUTE OUT 9 16 LOUT- 10 11 12 15 14 13 3 4 20 19 6 7 MUTE IN GND/HS 18 GND/HS NC ROUT+ RLINEIN RHPIN Thermal Pad RBYPASS RVDD NC HP/LINE ROUTSE/BTL GND/HS Top View Bottom View For TSSOP-P Only For SOP and TSSOP-P I/O Pin Name GND/HS Description No TJ 1,12, 13,24 2 O LOUT + L LINE IN 3 4 O I LHP IN 5 I LBYPASS LV DD SHUTDOWN 6 7 8 I I MUTE OUT LOUT - 9 10 O O MUTE IN 11 I SE/BTL 14 I ROUT- 15 O HP/ LINE 16 I Copyright ANPEC Electronics Corp. Rev. A.5 - July., 2002 Ground connection for circuitry, directly connected to thermal pad (only in TSSOP-P package). Shutdown m ode control signal input, sources a current proportional to the junction temperature. This pin should be left unconnected during normal operation. For more inform ation, see the junction temperature measurem ent section of this document. Left channel + output in BTL mode, + output in SE m ode. Left channel line input, selected when HP/ LINE pin (16) is held low. Left channel headphone input, selected when HP/ LINE pin (16) is held high. Connect to voltage divider for left channel internal mid-supply bias. Supply voltage input for left channel and for prim ary bias circuits. Shutdown m ode control signal input, places entire IC in shutdown mode when held high, IDD = 0.5µA. Follows MUTE in pin (11), provides buffered output. Left channel - output in BTL m ode, high-impedance state in SE mode. Mute control signal input, hold low for normal operation, hold high to mute. Mode control signal input, hold low for BTL mode, hold high for SE mode. Right channel - output in BTL mode, high impedance state in SE mode. MUX control input, hold high to select headphone inputs (5,20), hold low to select line inputs (4,21). 6 www.anpec.com.tw APA2020A Pin Description (Cont.) Pin Name I/O Description No NC RV DD RBYPASS 17,23 18 19 No internal connection. Supply voltage input for right channel. Connect to voltage divider for right channel internal mild-supply bias. I RHP IN 20 I Right channel headphone input, selected when HP/LINE pin (16) is held high. RLINE IN 21 I ROUT+ 22 O Right channel line input, selected when HP/LINE pin (16) is held low. Right channel + output in BTL mode, + output in SE mode. Test Information RF CI 4.7µF CO RF MUX RI RL=4 Ω , 8Ω or 32 Ω CI CB 4.7µF MUX RI RL= 4 Ω , 8 Ω or 32 Ω VDD CB SE/BTL SE/BTL HP/LINE HP/LINE Figure 2. BTL Test Circuit Copyright ANPEC Electronics Corp. Rev. A.5 - July., 2002 Figure 3. SE Test Circuit 7 www.anpec.com.tw APA2020A VDD=5V 5 f=1 KHz BTL 2 % THD+N- Total Harmonic Distortion + Noise 10 1 0.5 Ω RL=8Ω Ω RL=3Ω 0.2 0.1 0.06 0 500m 1 1.5 W 2 2.5 3 Po - Output Power Figure 4 10 5 2 THD+N- Total Harmonic Distortion + Noise THD+N- Total Harmonic Distortion + Noise THD+N- Total Harmonic Distortion + Noise Typical Characteristics VDD=5V AV=2 Ω RL=4Ω BTL 1 % PO=1.8W, RL=3Ω 0.5 PO=0.25W 0.2 PO=0.75W PO=1.5W 0.1 0.06 20 50 100 200 500 1k 2k 5k 20k Hz f - Frequency Figure 6 Copyright ANPEC Electronics Corp. Rev. A.5 - July., 2002 8 10 5 VDD=5V PO=1.5W RL=4Ω Ω 2 BTL AV=20 1 % AV=10 AV=2 0.5 0.2 AV=2 PO=1.8W, RL=3Ω 0.1 0.06 20 50 100 200 500 1k Hz 2k 5k 20k f - Frequency Figure 5 10 5 VDD=5V Ω RL=3Ω BTL 2 1 % f=20KHz 0.5 f=1KHz 0.2 f=20Hz 0.1 0.06 100m 200m 500m 1 2 5 10 W Po - Output Power Figure 7 www.anpec.com.tw 8 APA2020A THD+N- Total Harmonic Distortion + Noise 10 VDD=5V 5 AV=2 Ω RL=8Ω 2 BTL 1 % 0.5 PO=0.25W PO=0.5W PO=1W 0.2 0.1 0.06 20 50 100 200 500 1k 2k 5k 20k Hz f - Frequency- Hz Figure 8 10 5 2 % THD+N- Total Harmonic Distortion + Noise THD+N- Total Harmonic Distortion + Noise THD+N- Total Harmonic Distortion + Noise Typical Characteristics (Cont.) VDD=5V AV=2 Ω RL=8Ω BTL 1 0.5 f=20KHz 0.2 f=20Hz 0.1 f=1KHz 0.06 100m 200m 500m 1 W 2 5 10 Po - Output Power Figure 10 Copyright ANPEC Electronics Corp. Rev. A.5 - July., 2002 9 10 VDD=5V PO=1W RL=8Ω Ω 5 2 % BTL 1 0.5 AV=20 AV=10 AV=2 0.2 0.1 0.06 20 50 100 200 500 1k 2k 5k 20k Hz f - Frequency- Hz Figure 9 10 VDD=3.3V 5 f=1 KHz BTL 2 % 1 0.5 RL=8 Ω RL=3 Ω 0.2 0.1 0.06 0 200m 400m 600m 800m 1 W 1.2 1.4 Po - Output Power Figure 11 www.anpec.com.tw APA2020A VDD=3.3V PO=0.65W RL=4Ω Ω 5 2 % THD+N- Total Harmonic Distortion + Noise 10 BTL 1 AV=20 AV=10 0.5 AV=2 0.2 AV=2 PO=0.7W, RL=3Ω 0.1 0.06 20 50 100 200 500 1k Hz 2k 5k 20k f - Frequency Figure 12 10 % 5 VDD=3.3V 2 Ω RL=3Ω 1 f=20KHz 0.5 0.2 THD+N- Total Harmonic Distortion + Noise THD+N- Total Harmonic Distortion + Noise THD+N- Total Harmonic Distortion + Noise Typical Characteristics (Cont.) AV=2 BTL f=20Hz f=1KHz 0.1 0.06 100m 200m 500m 1 2 5 10 W Po - Output Power Figure 14 Copyright ANPEC Electronics Corp. Rev. A.5 - July., 2002 10 10 VDD=3.3V 5 AV=2 Ω RL=4Ω 2 % BTL 1 PO=0.1W 0.5 PO=0.35W PO=0.7W 0.2 PO=0.75W, R L=3Ω 0.1 0.06 20 50 100 200 500 1k Hz 2k 5k 20k f - Frequency Figure 13 10 VDD=3.3V PO=0.4W RL=8Ω Ω 5 2 BTL 1 % 0.5 AV=20 0.2 AV=10 0.1 AV=2 0.06 20 50 100 200 500 1k 2k 5k 20k Hz f - Frequency Figure 15 www.anpec.com.tw APA2020A 5 VDD=3.3V AV=2 2 % THD+N- Total Harmonic Distortion + Noise 10 Ω RL=8Ω BTL 1 0.5 PO=0.1W PO=0.25W PO=0.4W 0.2 0.1 0.06 20 50 100 200 500 1k 2k 5k 20k Hz f - Frequency Figure 16 10 5 2 1 THD+N- Total Harmonic Distortion + Noise THD+N- Total Harmonic Distortion + Noise THD+N- Total Harmonic Distortion + Noise Typical Characteristics (Cont.) VDD=5V PO=0.5W RL=4Ω Ω SE AV=10 0.5 % AV=5 0.2 0.1 0.05 AV=1 0.02 0.01 20 50 100 200 500 1k 2k 5k 20k Hz f - Frequency Figure 18 Copyright ANPEC Electronics Corp. Rev. A.5 - July., 2002 11 10 VDD=3.3V 5 AV=2 Ω RL=8Ω BTL 2 1 % f=20KHz 0.5 0.2 f=20Hz 0.1 f=1KHz 0.06 100m 200m 500m 1 2 5 10 W Po - Output Power Figure 17 10 VDD=5V AV=2 RL=4Ω Ω SE 5 2 1 % 0.5 PO=0.1W 0.2 PO=0.25W PO=0.4W 0.1 0.05 0.02 0.01 20 50 100 200 500 1k 2k 5k 20k Hz f - Frequency Figure 19 www.anpec.com.tw APA2020A 10 5 2 VDD=5V AV=2 RL=4Ω Ω 1 SE 0.5 THD+N- Total Harmonic Distortion + Noise THD+N- Total Harmonic Distortion + Noise Typical Characteristics (Cont.) f=20KHz % 0.2 0.1 f=100Hz 0.05 0.02 f=1KHz 0.01 10m 20m 50m 100m 200m W 500m 1 10 5 VDD=5V PO=0.25W RL=8Ω Ω SE 2 1 0.5 % 0.2 0.1 AV=10 0.05 AV=5 0.02 AV=1 0.01 20 50 100 200 500 1k 2k Hz 1 THD+N- Total Harmonic Distortion + Noise THD+N- Total Harmonic Distortion + Noise 10 2 VDD=5V Ω RL=8Ω SE 0.5 % 0.2 0.1 PO=0.25W PO=0.1W PO=0.05W 0.05 0.02 0.01 20 50 100 200 500 1k 2k 5k 20k Hz f- Frequency- Hz Figure 22 Copyright ANPEC Electronics Corp. Rev. A.5 - July., 2002 20k f - Frequency- Hz Figure 21 Po - Output Power Figure 20 5 5k 12 5 2 1 VDD=5V AV=2 RL=8Ω Ω SE 0.5 f=20KHz % 0.2 0.1 f=1KHz 0.05 0.02 0.01 10m f=100Hz 20m 50m 100m 200m 500m 1 W Po - Output Power Figure 23 www.anpec.com.tw APA2020A 5 2 1 THD+N- Total Harmonic Distortion + Noise 10 VDD=5V PO=0.075W RL=32Ω Ω SE 0.5 % 0.2 0.1 0.05 AV=10 0.02 AV=5 AV=1 0.006 20 50 100 200 500 1k 2k 5k 20k Hz f - Frequency- Hz Figure 24 10 5 2 1 THD+N- Total Harmonic Distortion + Noise THD+N- Total Harmonic Distortion + Noise THD+N- Total Harmonic Distortion + Noise Typical Characteristics (Cont.) VDD=5V Ω RL=32Ω SE 0.5 % 0.2 0.1 f=20KHz 0.05 0.02 f=20Hz 0.01 0.005 0.002 f=1KHz 0.001 10m 20m 50m 100m 200m W 500m 1 Po - Output Power Figure 26 Copyright ANPEC Electronics Corp. Rev. A.5 - July., 2002 13 10 5 VDD=5V Ω RL=32Ω SE 2 1 0.5 0.2 % 0.1 PO=25W PO=50W PO=75W 0.05 0.02 0.01 0.005 0.002 0.001 20 50 100 200 500 1k 2k 5k 20k 5k 20k Hz f - Frequency- Hz Figure 25 10 5 2 1 VDD=3.3V PO=0.2W RL=4Ω Ω SE 0.5 % 0.2 AV=10 0.1 AV=5 0.05 AV=1 0.02 0.01 20 50 100 200 500 1k 2k Hz f - Frequency- Hz Figure 27 www.anpec.com.tw APA2020A 5 THD+N- Total Harmonic Distortion + Noise 10 VDD=3.3V Ω RL=4Ω SE 2 1 0.5 % PO=0.05W 0.2 PO=0.1W PO=0.15W 0.1 0.05 0.02 0.01 20 50 100 200 500 1k 2k Hz 5k 20k f - Frequency Figure 28 THD+N- Total Harmonic Distortion + Noise THD+N- Total Harmonic Distortion + Noise THD+N- Total Harmonic Distortion + Noise Typical Characteristics (Cont.) 10 5 2 1 VDD=3.3V PO=100mW RL=8Ω Ω SE 0.5 % 0.2 0.1 AV=10 AV=5 0.05 0.02 0.01 20 AV=1 50 100 200 500 1k 2k 5k 20k Hz f - Frequency Figure 30 Copyright ANPEC Electronics Corp. Rev. A.5 - July., 2002 14 10 VDD=3.3V AV=2 RL=4Ω Ω SE 5 2 1 0.5 f=20KHz % 0.2 f=1KHz 0.1 0.05 f=100Hz 0.02 0.01 10m 20m 50m 100m 200m 500m 1 W Po - Output Power Figure 29 10 VDD=3.3V Ω RL=8Ω SE 5 2 1 0.5 % 0.2 PO=25mW PO=50mW PO=100mW 0.1 0.05 0.02 0.01 20 50 100 200 500 1k 2k Hz 5k 20k f - Frequency Figure 31 www.anpec.com.tw APA2020A 5 2 THD+N- Total Harmonic Distortion + Noise 10 VDD=3.3V Ω RL=8Ω SE 1 0.5 % 0.2 f=20KHz 0.1 f=1KHz 0.05 0.02 f=100Hz 0.01 10m 20m 50m 100m 200m 500m 1 W Po - Output Power Figure 32 10 5 2 1 THD+N- Total Harmonic Distortion + Noise THD+N- Total Harmonic Distortion + Noise THD+N- Total Harmonic Distortion + Noise Typical Characteristics (Cont.) VDD=3.3V Ω RL=32Ω SE 0.5 0.2 % 0.1 PO=10mW PO=20mW PO=30mW 0.05 0.02 0.01 0.005 0.002 0.001 20 50 100 200 500 1k 2k Hz 5k 20k f - Frequency Figure 34 Copyright ANPEC Electronics Corp. Rev. A.5 - July., 2002 15 10 5 VDD=3.3V PO=30mW RL=32Ω Ω SE 2 1 0.5 % 0.2 AV=10 0.1 AV=5 0.05 AV=1 0.02 0.006 20 50 100 200 500 1k 2k 5k 20k Hz f - Frequency Figure 33 10 VDD=3.3V Ω RL=32Ω SE 5 2 1 0.5 % 0.2 f=20KHz 0.1 0.05 f=20Hz 0.02 f=1KHz 0.01 10m 20m 50m 100m 200m W 500m 1 Po - Output Power Figure 35 www.anpec.com.tw APA2020A Typical Characteristics (Cont.) 100u 50u VO BTL 20u V VN- Output Noise Voltage - µV VN- Output Noise Voltage - µV 100u VO + SE 10u 5u VDD=5V BW=22Hz to 22 KHz 2u 1u 20 50 100 200 500 1k 2k 5k 20k 50u VO BTL 20u V VO + SE 10u 5u VDD=3.3V BW=22Hz to 22 KHz 2u 1u 20 50 100 200 Hz 5k 20k Hz f - Frequency Figure 36 f - Frequency Figure 37 +0 +0 -20 VDD=5V PO=1.5W RL=4Ω Ω -20 -40 BTL -40 Crosstalk Crosstalk 500 1k 2k -60 dB -80 Left to Right -100 -120 50 100 200 500 1k -60 Left to Right dB -80 Right to Left -100 Right to Left 20 VDD=3.3V PO=0.75W RL=4Ω Ω BTL 2k 5k -120 20k 20 50 100 200 500 1k 2k Hz Hz f - Frequency Figure 38 f - Frequency Figure 39 Copyright ANPEC Electronics Corp. Rev. A.5 - July., 2002 16 5k 20k www.anpec.com.tw APA2020A Typical Characteristics (Cont.) -20 Crosstalk -40 +0 VDD=5V PO=75mW RL=32Ω Ω SE -40 -60 dB Left to Right -80 -100 -120 20 Right to Left 50 100 200 VDD=3.3V PO=35mW RL=32Ω Ω SE -20 Crosstalk +0 500 1k 2k 5k -60 dB -80 Left to Right -100 Right to Left -120 20k 20 50 100 200 500 1k 2k Hz f - Frequency Figure 40 +10 VDD=5V +9 AV=2V/V +8 PO=1.5W +9 +8 +7 +7 Gain dB +5 +4 VDD=3.3V AV=2V/V PO=0.75W Gain +6 Gain Gain dB 20k f - Frequency Figure 41 +10 +6 5k Hz Phase +3 +5 +4 Phase +3 +2 +2 +1 +1 -0 -0 20 50 100200 5001k 2k 5k 10k20k 50k 200k 20 50 100200 500 1k 2k 5k 10k20k 50k 200k Hz Hz f- Frequency Figure 42 f- Frequency Figure 43 Copyright ANPEC Electronics Corp. Rev. A.5 - July., 2002 17 www.anpec.com.tw APA2020A Typical Characteristics (Cont.) -0 -0 -1 -1 -2 -3 -4 -5 -4 Gain -6 dB -5 Gain -6 -7 -7 Phase Phase -8 -8 -9 -9 -10 VDD=3.3V AV=1 V/V PO=0.25W -3 Gain Gain dB -2 VDD=5V AV=1 V/V PO=0.5W -10 20 50 100200 5001k 2k 5k 10k20k 50k 200k Hz 20 50 100200 5001k 2k 5k 10k20k 50k 200k f- Frequency Figure 44 f- Frequency Figure 45 Hz 9 3 THD +N = 1% BTL Stereo BTL 7 PO - Output Power - W IDD - Supply Current - mA 8 6 5 Stereo SE 4 3 2 1 0 2.5 2 RL=3 Ω RL=4 Ω 1.5 RL=8 Ω 1 0.5 0 2.5 3 3.5 4 4.5 5 5.5 6 2.5 VDD - Supply Voltage - V Figure 46 Copyright ANPEC Electronics Corp. Rev. A.5 - July., 2002 3 3.5 4 4.5 5 5.5 6 VDD - Supply Voltage - V Figure 47 18 www.anpec.com.tw APA2020A Typical Characteristics (Cont.) 3 THD +N = 1% SE 0.8 PO - Output Power - W PO - Output Power - W 1 Each Channel 0.6 RL= 4Ω R L= 8 Ω 0.4 0.2 RL= 32 Ω 0 THD +N = 1% BTL 2.5 Each Channel 2 VDD= 5V 1.5 1 VDD= 3.3V 0.5 0 2.5 3 3.5 4 4.5 5 5.5 6Ω RL= 32Ω 0 PD - Power Disspation - W PO - Output Power - W 1 THD +N = 1% SE Each Channel 0.6 0.4 VDD= 5V 0.2 0 4 8 12 12 16 20 1.8 24 28 32 RL=3 Ω 1.6 1.4 3Ω RL=3Ω 1.2 RL=4 Ω 1 0.8 RL= 8Ω Ω 0.6 VDD= 5V BTL 0.4 0.2 VDD=3.5V 0 8 RL - Load Resistance- Ω Figure 49 VDD - Supply Voltage - V Figure 48 0.8 4 Each Channel 0 16 20 24 28 32 0 1 1.5 2 2.5 PO - Output Power - W Figure 51 RL - Load Resistance- Ω Figure 50 Copyright ANPEC Electronics Corp. Rev. A.5 - July., 2002 0.5 19 www.anpec.com.tw APA2020A Typical Characteristics (Cont.) 0.4 0.8 0.6 PD - Power Disspation - W PD - Power Disspation - W RL= 3Ω Ω Ω RL= 4Ω 0.4 Ω RL=8Ω 0.2 VDD= 3.3V BTL Each Channel 5V VDD=5 SE Each Channel 0.3 RL= 4Ω 0.2 R L= 8 Ω 0.1 0 0 0 0.25 0.5 0.75 0 1 PO - Output Power - W Figure 52 0.1 0.2 0.3 0.4 0.5 0.6 PO - Output Power - W Figure 53 PD - Power Disspation - W 0.4 3.3 VDD =3.3 3.3V SE Each Channel 0.3 0.2 RL= 4Ω 0.1 RL= 8 Ω 0 0 0.05 0.1 0.15 0.2 0.25 PO - Output Power - W Figure 54 Copyright ANPEC Electronics Corp. Rev. A.5 - July., 2002 20 www.anpec.com.tw APA2020A Packaging Information SO – 300mil ( Reference JEDEC Registration MS-013) D N H GAUGE PLANE E 1 2 3 A Millimeters 1 A1 B e L Variations- D Inches Variations- D Dim Min. Max. Variations Min. Max. Dim Min. Max. Variations Min. Max. A 2.35 2.65 SO-16 10.10 10.50 A 0.093 0.1043 SO-16 0.398 0.413 A1 0.10 0.30 SO-18 11.35 11.76 A1 0.004 0.0120 SO-18 0.447 0.463 B 0.33 0.51 SO-20 12.60 13 B 0.013 0.020 SO-20 0.496 0.512 D See variations SO-24 15.20 15.60 D See variations SO-24 0.599 0.614 E 7.40 SO-28 17.70 18.11 E SO-28 0.697 0.713 SO-14 8.80 9.20 e SO-14 0.347 0.362 e 7.60 1.27BSC 0.2914 0.2992 0.050BSC H 10 10.65 H 0.394 0.419 L 0.40 1.27 L 0.016 0.050 N See variations N See variations 0° φ1 φ1 8° Copyright ANPEC Electronics Corp. Rev. A.5 - July., 2002 21 0° 8° www.anpec.com.tw APA2020A Packaging Information T S S O P / T S S O P -P ( R eference JE D E C R egistration M O -153) e N 2x E/2 E1 1 2 3 E e/2 D A2 A ( A1 b D1 2) GAUGE PLANE S EXPOSED THERMAL PAD ZONE E2 0.25 L 1 (L1) ( 3) BOTTOM VIEW (THERMALLY ENHANCED VARIATIONDS ONLY) D im A A1 A2 D D1 e E E1 E2 L L1 R R1 S φ1 φ2 φ3 M illim eters Inches M in. M ax. 1.2 0.00 0.15 0.80 1.05 6.4 (N =20P IN ) 6.6 (N =20P IN ) 7.7 (N =24P IN ) 7.9 (N =24P IN ) 9.6 (N =28P IN ) 9.8 (N =28P IN ) 4.2 B S C (N =20P IN ) 4.7 B S C (N =24P IN ) 3.8 B S C (N =28P IN ) 0.65 B S C 6.40 B S C 4.30 4.50 3.0 B S C (N =20P IN ) 3.2 B S C (N =24P IN ) 2.8 B S C (N =28P IN ) 0.45 0.75 1.0 R E F 0.09 0.09 0.2 0° 8° 12° R E F 12° R E F Copyright ANPEC Electronics Corp. Rev. A.5 - July., 2002 22 M in. M ax. 0.047 0.000 0.006 0.031 0.041 0.252 (N =20P IN ) 0.260 (N =20P IN ) 0.303 (N =24P IN ) 0.311 (N =24P IN ) 0.378 (N =28P IN ) 0.386 (N =28P IN ) 0.165 B S C (N =20P IN ) 0.188 B S C (N =24P IN ) 0.150 B S C (N =28P IN ) 0.026 B S C 0.252 B S C 0.169 0.177 0.118 B S C (N =20P IN ) 0.127 B S C (N =24P IN ) 0.110 B S C (N =28P IN ) 0.018 0.030 0.039R E F 0.004 0.00 4 0.008 0° 8° 12° R E F 12° R E F www.anpec.com.tw APA2020A Physical Specifications Terminal Material Lead Solderability Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb) Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3. Reflow Condition (IR/Convection or VPR Reflow) temperature Reference JEDEC Standard J-STD-020A APRIL 1999 Peak temperature 183°C Pre-heat temperature Time Classification Reflow Profiles Convection or IR/ Convection Average ramp-up rate(183°C to Peak) 3°C/second max. 120 seconds max Preheat temperature 125 ± 25°C) 60 – 150 seconds Temperature maintained above 183°C Time within 5°C of actual peak temperature 10 –20 seconds Peak temperature range 220 +5/-0°C or 235 +5/-0°C Ramp-down rate 6 °C /second max. 6 minutes max. Time 25°C to peak temperature VPR 10 °C /second max. 60 seconds 215-219°C or 235 +5/-0°C 10 °C /second max. Package Reflow Conditions pkg. thickness ≥ 2.5mm and all bgas Convection 220 +5/-0 °C VPR 215-219 °C IR/Convection 220 +5/-0 °C pkg. thickness < 2.5mm and pkg. volume ≥ 350 mm³ Copyright ANPEC Electronics Corp. Rev. A.5 - July., 2002 23 pkg. thickness < 2.5mm and pkg. volume < 350mm³ Convection 235 +5/-0 °C VPR 235 +5/-0 °C IR/Convection 235 +5/-0 °C www.anpec.com.tw APA2020A Reliability test program Test item SOLDERABILITY HOLT PCT TST ESD Latch-Up Method MIL-STD-883D-2003 MIL-STD-883D-1005.7 JESD-22-B, A102 MIL-STD-883D-1011.9 MIL-STD-883D-3015.7 JESD 78 Description 245°C , 5 SEC 1000 Hrs Bias @ 125 °C 168 Hrs, 100 % RH , 121°C -65°C ~ 150°C, 200 Cycles VHBM > 2KV, VMM > 200V 10ms , Itr > 100mA Carrier Tape & Reel Dimensions D P Po t E P1 Bo F W Ko Ao D1 T2 J C A B T1 Application SOP- 24 A B J T1 T2 W 62 ±1.5 C 12.75 ± 0.15 330±1 2 ± 0.6 24.4 ± 0.2 2± 0.2 24 ± 0.3 F D D1 Po P1 Ao Bo 11.5 ± 0.1 1.55 +0.1 1.5+ 0.25 4.0 ± 0.1 2.0 ± 0.1 10.9 ± 0.1 15.9± 0.1 P E 12 ± 0.1 1.75± 0.1 Ko t 3.1± 0.1 0.35±0.05 (mm) Copyright ANPEC Electronics Corp. Rev. A.5 - July., 2002 24 www.anpec.com.tw APA2020A Cover Tape Dimensions Application SOP- 16 / 20 / 24 / 28 Carrier Width 24 Cover Tape Width 21.3 Devices Per Reel 1000 Customer Service Anpec Electronics Corp. Head Office : 5F, No. 2 Li-Hsin Road, SBIP, Hsin-Chu, Taiwan, R.O.C. Tel : 886-3-5642000 Fax : 886-3-5642050 Taipei Branch : 7F, No. 137, Lane 235, Pac Chiao Rd., Hsin Tien City, Taipei Hsien, Taiwan, R. O. C. Tel : 886-2-89191368 Fax : 886-2-89191369 Copyright ANPEC Electronics Corp. Rev. A.5 - July., 2002 25 www.anpec.com.tw