® ADS7811 ADS 781 1 16-Bit 250kHz Sampling CMOS ANALOG-to-DIGITAL CONVERTER FEATURES DESCRIPTION ● 250kHz SAMPLING RATE ● COMPLETE WITH S/H, REF, CLOCK, ETC. ● 96dB min SFDR WITH 100kHz INPUT The ADS7811 is a complete 16-bit sampling analogto-digital (A/D) converter featuring excellent AC performance and a 250kHz throughput rate. The design includes a 16-bit capacitor-based SAR A/D converter with an inherent sample and hold (S/H), a precision reference, and an internal clock. Spuriousfree dynamic range with a 100kHz full-scale sinewave input is typically greater than 100dB. The ±2.5V input range allows development of precision systems using only ±5V supplies. The converter is available in a 28-lead SOIC package specified for operation over the industrial –25°C to +85°C temperature range. ● 84dB min SINAD ● ±2.5V INPUT RANGE ● 28-LEAD SOIC APPLICATIONS ● WIRELESS BASE STATIONS ● SPECTRUM ANALYSIS ● IMAGING SYSTEMS ● DATA ACQUISITION R/C Clock Successive Approximation Register and Control Logic CS BUSY CDAC Output ±2.5V Input Latches and Comparator Three Parallel Data Bus State Drivers Buffer 5kΩ REF Out/In Internal +2.5V Ref International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 • Twx: 910-952-1111 Internet: http://www.burr-brown.com/ • FAXLine: (800) 548-6133 (US/Canada Only) • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132 ® © 1997 Burr-Brown Corporation PDS-1300A 1 ADS7811 Printed in U.S.A. November, 1997 SPECIFICATIONS At TA = –25°C to +85°C, fS = 250kHz, +VS = +5V, and –VS = –5V, using internal reference, unless otherwise specified. ADS7811U PARAMETER CONDITIONS MIN TYP RESOLUTION ANALOG INPUT Voltage Range Impedance Capacitance DC ACCURACY Integral Linearity Error No Missing Codes Transition Noise(2) Full Scale Error(3) Full Scale Error Drift Full Scale Error(3) Full Scale Error Drift Bipolar Zero Error Bipolar Zero Error Drift Power Supply Sensitivity AC ACCURACY Spurious-Free Dynamic Range Total Harmonic Distortion Signal-to-(Noise+Distortion) Signal-to-Noise Usable Bandwidth(5) Aperture Delay REFERENCE Internal Reference Voltage Internal Reference Source Current Internal Reference Drift External Reference Voltage Range External Reference Current Drain Acquire and Convert V MΩ pF 4.0 µs kHz ±4 LSB(1) Bits LSB % ppm/°C % ppm/°C mV ppm/°C LSB 15 0.8 External 2.5000V Reference External 2.5000V Reference ±7 ±0.2 2 +VS ±5%, –VS ±5% ±2 ±6 fIN = 100kHz fIN = 100kHz fIN = 100kHz –60dB Input fIN = 100kHz 96 84 84 2.48 100 –98 87 28 87 1 40 2.5 1 15 2.5 VREF = +2.5V –0.3 +2.8 Output Capacitance Bits 250 DIGITAL INPUTS Logic Levels VIL VIH IIL IIH DIGITAL OUTPUTS Data Format Data Coding VOL VOH Leakage Current UNITS 16 ±2.5V 100 30 After Input Capacitor is Charged THROUGHPUT SPEED Conversion Cycle Throughput Rate MAX ±0.5 ±10 ±16 –96 2.52 dB(4) dB dB dB dB MHz ns 100 V µA ppm/°C V µA +0.8 +VS +0.3V ±10 ±10 V V µA µA +0.4 ±5 V V µA 15 pF 83 83 ns ns +5.25 –4.75 250 V V mA mA mW +85 +125 °C °C Parallel 16 bits Binary Two’s Complement ISINK = 1.6mA ISOURCE = 200µA High-Z State, VOUT = 0V to VDIG High-Z State +4 DIGITAL TIMING Bus Access Time Bus Relinquish Time POWER SUPPLIES +VS –VS +IS –IS Power Dissipation +4.75 –5.25 TEMPERATURE RANGE Specified Performance Storage –25 –55 +5 –5 +30 –10 200 NOTES: (1) LSB means Least Significant Bit. For the 16-bit, ±2.5V input ADS7811, one LSB is 76µV. (2) Typical rms noise at worst case transitions and temperatures. (3) Full scale error is the worst case of –Full Scale or +Full Scale untrimmed deviation from ideal first and last code transitions, divided by the transition voltage (not divided by the full-scale range) and includes the effect of offset error. (4) All specifications in dB are referred to a full-scale ±2.5V input. (5) Usable Bandwidth defined as Full-Scale input frequency at which Signal-to-(Noise+Distortion) degrades to 60dB, or 10 bits of accuracy. ® ADS7811 2 ABSOLUTE MAXIMUM RATINGS PACKAGE/ORDERING INFORMATION Analog Inputs: VIN .............................................. –VS – 0.3V to +VS + 0.3V REF ................................................... – 0.3V to +VS + 0.3V CAP ............................................... Indefinite Short to GND Momentary Short to +VS +VS ......................................................................................................... 7V –VS ...................................................................................................... –7V Digital Inputs .............................................................. –0.3V to +VS + 0.3V Maximum Junction Temperature ................................................... +165°C Internal Power Dissipation ............................................................. 825mW Lead Temperature (soldering, 10s) ................................................ +300°C PRODUCT PACKAGE PACKAGE DRAWING NUMBER(1) ADS7811U 28-Pin SOIC 217 TEMPERATURE RANGE –25°C to +85°C NOTE: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix C of Burr-Brown IC Data Book. ELECTROSTATIC DISCHARGE SENSITIVITY This integrated circuit can be damaged by ESD. Burr-Brown recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems. ® 3 ADS7811 PIN # NAME 1 2 3 VIN GND REF 4 5 6 CAP GND D15 (MSB) 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 D14 D13 D12 D11 D10 D9 D8 GND D7 D6 D5 D4 D3 D2 D1 D0 (LSB) 23 24 –VS R/C 25 CS 26 BUSY 27 28 +VS +VS DESCRIPTION Analog Input. Full-scale input range is ±2.5V. Ground. Reference Input/Output. Outputs internal reference of +2.5V nominal. Can also be driven by external system reference. In both cases, connect to ground with a 0.1µF ceramic capacitor in parallel with 2.2µF tantalum capacitor. Reference compensation capacitor. Use a parallel combination of a 0.1µF ceramic capacitor and a 2.2µF tantalum capacitor. Ground. Data Bit 15. Most Significant Bit (MSB) of conversion results. Hi-Z state when CS is HIGH, when R/C is LOW or when a conversion is in progress. Data Bit 14. Hi-Z state when CS is HIGH, when R/C is LOW or when a conversion is in progress. Data Bit 13. Hi-Z state when CS is HIGH, when R/C is LOW or when a conversion is in progress. Data Bit 12. Hi-Z state when CS is HIGH, when R/C is LOW or when a conversion is in progress. Data Bit 11. Hi-Z state when CS is HIGH, when R/C is LOW or when a conversion is in progress. Data Bit 10. Hi-Z state when CS is HIGH, when R/C is LOW or when a conversion is in progress. Data Bit 9. Hi-Z state when CS is HIGH, when R/C is LOW or when a conversion is in progress. Data Bit 8. Hi-Z state when CS is HIGH, when R/C is LOW or when a conversion is in progress. Ground. Data Bit 7. Hi-Z state when CS is HIGH, when R/C is LOW or when a conversion is in progress. Data Bit 6. Hi-Z state when CS is HIGH, when R/C is LOW or when a conversion is in progress. Data Bit 5. Hi-Z state when CS is HIGH, when R/C is LOW or when a conversion is in progress. Data Bit 4. Hi-Z state when CS is HIGH, when R/C is LOW or when a conversion is in progress. Data Bit 3. Hi-Z state when CS is HIGH, when R/C is LOW or when a conversion is in progress. Data Bit 2. Hi-Z state when CS is HIGH, when R/C is LOW or when a conversion is in progress. Data Bit 1. Hi-Z state when CS is HIGH, when R/C is LOW or when a conversion is in progress. Data Bit 0. Least Significant Bit (LSB) of conversion results. Hi-Z state when CS is HIGH, when R/C is LOW or when a conversion is in progress. Negative supply input. Nominally –5V. Decouple to analog ground with 0.1µF ceramic and 10µF tantalum capacitors. Read/convert input. With R/C HIGH, CS going LOW will enable the output data bits if a conversion is not in progress. With R/C LOW, CS going LOW will start a conversion if one is not already in progress. Chip select. With R/C LOW, CS going LOW will initiate a conversion if one is not already in progress. With R/C HIGH, CS going LOW will enable the output data bits if a conversion is not in progress. Busy output. Falls when a conversion is started, and remains LOW until the conversion is completed. With CS LOW and R/C HIGH, output data will be valid when BUSY rises, so that the rising edge can be used to latch the data. CS or R/C must be HIGH within 250ns after BUSY rises or another conversion will start without time for signal acquisition. Positive supply input. Nominally +5V. Connect directly to pin 28. Positive supply input. Nominally +5V. Connect directly to pin 27. Decouple to ground with 0.1µF ceramic and 10µF tantalum capacitors. TABLE I. Pin Assignments. PIN CONFIGURATION Top View SOIC VIN 1 28 +VS GND 2 27 +VS REF 3 26 BUSY CAP 4 25 CS GND 5 24 R/C D15 (MSB) 6 23 –VS D14 7 22 D0 (LSB) ADS7811 D13 8 21 D1 D12 9 20 D2 D11 10 19 D3 D10 11 18 D4 D9 12 17 D5 D8 13 16 D6 GND 14 15 D7 ® ADS7811 4 TYPICAL PERFORMANCE CURVES At TA = –25°C to +85°C, fS = 250kHz, +VS = +5V, and –VS = –5V, using internal reference, unless otherwise specified. FREQUENCY SPECTRUM (4096 Point FFT; fIN = 99kHz, –0.5dB) 0 0 –20 –20 –40 –40 Amplitude (dB) Amplitude (dB) FREQUENCY SPECTRUM (4096 Point FFT; fIN = 9.9kHz, –0.5dB) –60 –80 –100 –60 –80 –100 –120 –120 –140 –140 0 25 50 75 100 0 125 25 50 100 125 INTEGRAL LINEARITY ERROR AND DIFFERENTIAL LINEARITY ERROR vs OUTPUT CODE FREQUENCY SPECTRUM (4096 Point FFT; fIN = 247kHz, –0.5dB) 0 ILE (LSB) 4 –20 –40 –60 2 0 –2 –4 –80 4 –100 2 DLE (LSB) Amplitude (dB) 75 Frequency (kHz) Frequency (kHz) –120 –140 0 25 50 75 100 0 –2 –4 8000h 125 C000h 0000h 4000h 7FFFh Frequency (kHz) Hex BTC Code REFERENCE VOLTAGE vs TEMPERATURE 3.70 2.520 3.65 2.515 3.60 2.510 Reference Voltage (V) Conversion Time (µs) CONVERSION TIME (t2 + t4) vs TEMPERATURE 3.55 3.50 3.45 3.40 2.505 2.500 2.495 2.490 2.485 3.35 2.480 3.30 –30 –10 10 30 50 70 –30 90 –10 10 30 50 70 90 Temperature (°C) Temperature (°C) ® 5 ADS7811 BASIC OPERATION is placed on these outputs. In the circuit shown in Figure 1, the rising edge of BUSY latches the result into the 74HC574s. Figure 1 shows the recommended circuit for operation of the ADS7811. A falling edge on the convert pulse signal places the sample and hold into the hold mode and initiates a conversion. When the conversion is complete, the pins D15 through D0 become active and the result of the conversion After the conversion is complete, the ADS7811 sample and hold returns to the sample mode and begins acquiring the input signal for the next conversion. Allowing 4µs between falling edges of the convert pulse signal assures adequate acquisition time for the internal sample and hold. R1 75Ω +5V R2 10Ω OPA628 –5V 2.2µF C3 2.2µF C4 + + 0.1µF C5 0.1µF C6 1 VIN +VS 28 2 GND +VS 27 3 REF BUSY 26 4 CAP CS 25 5 GND R/C 24 6 D15 –VS 23 7 8 D0 22 D14 ADS7811 D1 21 D13 9 D12 D2 20 10 D11 D3 19 11 D10 D4 18 2 12 D9 D5 17 3 13 D8 D6 16 4 14 GND D7 15 5 0.1µF C1 + +5V 10µF C2 Convert Pulse 74HC00 0.1µF C7 –5V 100ns min 3.3µs max 10µF + C8 OC 1 10 6 7 8 9 OC CLK 1D 1Q 2D 2Q 3D 3Q 4D 4Q 5D 5Q 6D 6Q 7D 7Q 8D 8Q µProcessor Bus 74HC574 1 10 2 3 4 5 6 7 8 9 OC CLK 1D 1Q 2D 2Q 3D 3Q 4D 4Q 5D 5Q 6D 6Q 7D 7Q 8D 8Q 74HC574 FIGURE 1. Basic Operation. ® ADS7811 6 µProcessor Bus TIMING the digital outputs tri-stating while the sample and hold transitions to the hold mode. The change in digital outputs results in noise being coupled onto the hold capacitor. The timing shown in Figure 2 and Table II is the recommended method of operating the ADS7811. The falling edge of CS initiates the conversion. During the conversion, the digital outputs are tri-stated and BUSY is LOW. Near the end of the conversion, the digital outputs become active with the most recent conversion result. After a brief delay (see time t11 in Figure 2 and Table II), BUSY rises. The rising edge of BUSY is used to latch the digital result in Figure 1. If a conversion is not in progress or is just about to finish, the digital outputs will be active when R/C is HIGH and CS is LOW. This is shown in Figure 2 and Figure 3. It is possible to return CS HIGH during the initial part of the conversion (as is done with R/C) and prevent the digital outputs from becoming active. At a later time, the digital results could be read by taking CS LOW. It is also possible to leave R/C LOW, take CS HIGH during the conversion, and read the results at a later time by taking R/C HIGH and CS LOW. R/C AND CS The R/C (read/convert) and CS signals control the start of conversion and, when a conversion is not in progress, the status of the digital outputs D15 through D0. It is possible to start a conversion by taking CS LOW and then taking R/C LOW. However, this is not recommended and will result in a significant decrease in signal-to-noise ratio. This is due to SYMBOL DESCRIPTION MIN t2 TYP MAX UNITS 200 ns t1 CS to R/C Delay t2 CS to BUSY Delay 40 ns t3 Aperture Delay 40 ns 3.5 µs t4 BUSY LOW t5 R/C LOW to CS LOW t6 BUSY HIGH to CS HIGH t7 Bus Access Time t8 Bus Relinquish Time 83 ns t9 Throughput Time 4 µs 100 t10 Conversion Time Data Valid to BUSY HIGH 25 t12 CS to R/C Setup Time 40 R/C and CS should remain static prior to that start of conversion and during the later part of a conversion. To start t12 R/C ns 10 t11 Following a conversion, if R/C and CS are both LOW 250ns after BUSY rises, then a new conversion will be initiated without allowing the proper acquisition period for the sample and hold. R/C must remain HIGH or CS must be taken HIGH within 250ns of BUSY rising. 250 ns 83 ns 3.4 µs 35 ns t7 t8 CS D15 - D0 DataValid Hi-Z State Hi-Z State Acquire MODE ns TABLE II. Conversion Timing. FIGURE 3. Bus Timing. t1 t5 R/C t6 t9 CS t2 t4 BUSY t8 Hi-Z State D15 - D0 DataValid Hi-Z State t11 t3 MODE Acquire Convert Acquire t10 FIGURE 2. ADS7811 Timing. ® 7 ADS7811 a conversion, R/C should be taken LOW at least 100ns before CS is taken LOW. R/C and/or CS should be taken HIGH during the early part of the conversion, preferably within 200ns of the start of the conversion. If these times are not observed, then there is risk that the transition of these digital signals may affect the conversion result. to that listed in the Specifications Table. The range for the external reference is 2.3V to 2.7V. While the ADS7811 will operate using an external reference, the specifications are only guaranteed when the internal reference is used. REF PIN The REF pin itself should be bypassed with a 0.1µF ceramic capacitor in parallel with a 2.2µF tantalum capacitor. While both capacitors should be physically close to the ADS7811, it is very important that the ceramic capacitor be placed as close as possible. The three NAND gates shown in Figure 1 can be used to generate R/C and CS signals from a single negative going pulse. The pulse must not be longer than 3.3µs or a second conversion may be initiated immediately after the first. BUSY BUSY goes LOW when a conversion is started and remains LOW throughout the conversion. Just prior to BUSY going HIGH, the digital outputs become active with the conversion result. Time t11, shown in Figure 2, should provide adequate time for the ADS7811 to drive the digital outputs to a valid logic state before BUSY rises. As shown in Figure 1 and 2, the rising edge of BUSY can be used to latch the digital result into an external component. The REF voltage should not be used to drive a large load or any load which is dynamic. A large load will reduce the reference voltage and the corresponding input range of the converter. A dynamic load will modulate the reference voltage and this modulation will be present in the converter’s output data. CAP PIN The voltage on the CAP pin is the output of the reference buffer. This pin should be bypassed with a 0.1µF ceramic capacitor in parallel with a 2.2µF tantalum capacitor. While both capacitors should be physically close to the ADS7811, it is very important that the ceramic capacitor be placed as close as possible. DIGITAL OUTPUT The ADS7811’s digital output is in Binary Two’s Complement (BTC) format. Table III shows the relationship between the digital output word and analog input voltage under ideal conditions. The CAP pin connects to the internal reference buffer and directly to the binary weighted capacitor array of the converter. Thus, the signal at the CAP pin has high-frequency glitches which occur at each bit decision. For this reason, the CAP voltage should not be used to provide a reference voltage for external circuitry. DIGITAL OUTPUT ANALOG INPUT DESCRIPTION BINARY CODE HEX CODE 2.499924V 0111 1111 1111 1111 7FFF Full Scale Range ±2.5V Least Significant Bit (LSB) 76µV +Full Scale (2.5V – 1LSB) Midscale BINARY TWO’S COMPLEMENT LAYOUT 0V 0000 0000 0000 0000 0000 One LSB below Midscale –76µV 1111 1111 1111 1111 FFFF –Full Scale –2.5V 1000 0000 0000 0000 8000 The layout of the ADS7811 and accompanying components will be critical for optimum performance. Use of an analog ground plane is essential. Use of +5V and –5V power planes is not critical as long as the supplies are well bypassed, and the traces connecting +5V and –5V to the power connector are not too long or too thin. Table III. Ideal Input Voltages and Output Codes. The two +VS power pins of the ADS7811 must be tied together. The voltage source for these pins should also power the input buffer and the 74HC00 shown in Figure 1. This supply should separate from the positive +5V supply for the system’s digital logic REFERENCE The ADS7811 can be operated with the internal 2.5V reference or an external reference. By applying an external reference to the REF pin, the internal reference is bypassed. The reference voltage at REF is buffered internally. Three ground pins are present on the ADS7811: pin 2, pin 5, and pin 14. These should all be tied to the analog ground plane. The analog ground plane should extend underneath all analog signal conditioning components and up to the 74HC574s (or equivalent components) shown in Figure 1. The 74HC574s should not be located more than several inches from the ADS7811. The voltage at the reference input sets the full-scale range of the converter. With the internal 2.5V reference, the input range is ±2.5V. Thus, the input range of the converter’s analog input is simply ±VREF, where VREF is the voltage at the reference input. Because of internal gain and offset error, the input range will not be exactly ±VREF. The full-scale error of the converter with an external reference will typically be 0.25% or less. The bipolar zero error will be similar The ground for the 74HC574s should be connected to the digital ground. The analog ground plane should extend up to ® ADS7811 8 SIGNAL CONDITIONING The ADS7811 input essentially consists of a switch and a capacitor. In the acquisition or sample mode, the switch is closed and the input signal drives the capacitor directly. When a conversion is started, the switch is opened capturing the input signal at that moment. This voltage is held on the capacitor for the remainder of the conversion. the 74HC574s but should be kept at least 1/4" (6mm) distant from the digital ground plane (if present). The analog and digital grounds planes should not overlap at any point. INTERMEDIATE LATCHES The 74HC574s shown in Figure 1 isolate the ADS7811 from digital signals on a microprocessor, digital signal processor (DSP), or microcontroller bus. This is necessary because of the precision needed within the ADS7811. The weight of a single LSB in the ADS7811 is 76µV, and the comparator must be able to resolve differences in voltage to this level. External digital signals which transition during the conversion can easily couple onto the substrate and produce voltages larger than this. While this provides for a wide bandwidth sample and hold function and results in excellent AC performance, this architecture requires a high bandwidth, precision op amp to drive the analog input. The op amp and configuration shown in Figure 1 is highly recommended. The amplifier should be placed within 1 to 2 inches (25 to 50mm) of the ADS7811, and the layout guidelines in the OPA628 data sheet should be strictly followed. In place of the 74HC574s, it might be possible to use a FIFO or similar type of memory device. For many systems, it may be difficult to go directly from the ADS7811 into a microcontroller or DSP even if the ADS7811 is not connected to shared bus. The reason for this is that the outputs are active only during the acquisition period. ® 9 ADS7811