CSPEMI201A 2 Channel Headset Speaker EMI Filter with ESD Protection Features Product Description • • The CSPEMI201A is a dual low-pass filter array integrating two pi-style filters (C-R-C) that reduce EMI/RFI emissions while at the same time providing ESD protection. This part is custom-designed to interface with a speaker port on a cellular telephone or similar device. Each high quality filter provides more than 35dB attenuation in the 800-2700 MHz range. These pi-style filters support bidirectional filtering, controlling EMI both to and from a speaker element. They also support bipolar signals with a cutoff frequency of 31MHz, enabling audio signals to pass through without distortion. • • • • • • • • Two channels of EMI filtering Pi-style EMI filters in a capacitor-resistor-capacitor (C-R-C) network Greater than 40dB attenuation at 1GHz +8kV ESD protection on each channel (IEC 61000-4-2 Level 4, contact discharge) +15kV ESD protection in each channel (HBM) Supports AC signals—ideal for audio applications Extremely low lead inductance for optimum filter and ESD performance 5-bump, 0.950mm X 1.410mm footprint Chip Scale Package (CSP) Lead-free version available In addition, the CSPEMI201A provides a very high level of protection for sensitive electronic components that may be subjected to electrostatic discharge (ESD). The CSPEMI201A can safely dissipate ESD strikes of 8kV, the maximum requirement of the IEC 61000-4-2 international standard. Using the MIL-STD-883 (Method 3015) specification for Human Body Model (HBM) ESD, the device provides protection for contact discharges to greater than 15kV. Applications • • • • • • • EMI filtering and ESD protection for headset speaker ports Wireless Handsets Handheld PCs / PDAs MP3 Players Digital Camcorders Notebooks Desktop PCs The CSPEMI201A is particularly well suited for portable electronics (e.g., cellular telephones, PDAs, notebook computers) because of its small package format and low weight. The CSPEMI201A is available in a space-saving, low-profile Chip Scale Package with optional lead-free finishing. Electrical Schematic SPKR_IN1 A1 10Ω 100pF SPKR_IN2 A3 SPKR_OUT1 100pF 10Ω 100pF GND C1 C3 SPKR_OUT2 100pF B2 © 2003 California Micro Devices Corp. All rights reserved. 10/09/03 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 ▲ Tel: 408.263.3214 ▲ Fax: 408.263.7846 ▲ www.calmicro.com 1 CSPEMI201A PACKAGE / PINOUT DIAGRAMS BOTTOM VIEW (Bumps Up View) TOP VIEW (Bumps Down View) Orientation Marking (see note 2) 1 2 3 SPKR_OUT1 SPKR_OUT2 A C3 GND AB B C1 B2 Pin "A1" Marking C SPKR_IN1 SPKR_IN2 A1 A3 A1 CSPEMI201A CSP Package Notes: 1) These drawings are not to scale. 2) Lead-free devices are specified by using a "+" character for the top side orientation mark. PIN DESCRIPTIONS PIN NAME A1 SPKR_IN1 DESCRIPTION Speaker Input 1 (from audio circuitry) A3 SPKR_IN2 Speaker Input 2 (from audio circuitry) B2 GND C1 SPKR_OUT1 Speaker Output 1 (to speaker) C3 SPKR_OUT2 Speaker Output 2 (to speaker) Device Ground Ordering Information PART NUMBERING INFORMATION Lead-free Finish2 Standard Finish Ordering Part Pins Package Number1 5 CSP CSPEMI201A Ordering Part Part Marking Number1 Part Marking AB CSPEMI201AG AB Note 1: Parts are shipped in Tape & Reel form unless otherwise specified. Note 2: Lead-free devices are specified by using a "+" character for the top side orientation mark. © 2003 California Micro Devices Corp. All rights reserved. 2 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 ▲ Tel: 408.263.3214 ▲ Fax: 408.263.7846 ▲ www.calmicro.com 10/09/03 CSPEMI201A Specifications ABSOLUTE MAXIMUM RATINGS PARAMETER RATING UNITS -65 to +150 °C DC Power per Resistor 100 mW DC Package Power Rating 200 mW RATING UNITS -40 to +85 °C Storage Temperature Range STANDARD OPERATING CONDITIONS PARAMETER Operating Temperature Range ELECTRICAL OPERATING CHARACTERISTICS1 SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS R Resistance 9 10 11 Ω C Capacitance 80 100 120 pF 1.0 µA 15 -15 V V ILEAK Diode Leakage Current VIN=5.0V VSIG Signal Voltage Positive Clamp Negative Clamp ILOAD = 10mA In-system ESD Withstand Voltage a) Human Body Model, MIL-STD-883, Method 3015 b) Contact Discharge per IEC 61000-4-2 Level 4 Notes 2,4 and 5 Clamping Voltage during ESD Discharge MIL-STD-883 (Method 3015), 8kV Positive Transients Negative Transients Notes 2,3,4 and 5 Cut-off frequency ZSOURCE = 50Ω, ZLOAD = 50Ω R = 10Ω, C = 100pF VESD VCL fC 5 -5 7 -10 ±15 kV ±8 kV +15 -19 V V 31 MHz Note 1: TA=25°C unless otherwise specified. Note 2: ESD applied to input and output pins with respect to GND, one at a time. Note 3: Clamping voltage is measured at the opposite side of the EMI filter to the ESD pin. For example, if ESD is applied to Pin A1, then clamping voltage is measured at Pin C1. Note 4: Unused pins are left open Note 5: These parameters are guaranteed by design and characterization. © 2003 California Micro Devices Corp. All rights reserved. 10/09/03 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 ▲ Tel: 408.263.3214 ▲ Fax: 408.263.7846 ▲ www.calmicro.com 3 CSPEMI201A Performance Information Typical Filter Performance (nominal conditions unless specified otherwise, 50 Ohm Environment) Figure 1. Insertion Loss VS. Frequency (A1-C1 to GND B2) Figure 2. Insertion Loss VS. Frequency (A3-C3 to GND B2) © 2003 California Micro Devices Corp. All rights reserved. 4 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 ▲ Tel: 408.263.3214 ▲ Fax: 408.263.7846 ▲ www.calmicro.com 10/09/03 CSPEMI201A Application Information Refer to Application Note AP-217, "The Chip Scale Package", for a detailed description of Chip Scale Packages offered by California Micro Devices. PRINTED CIRCUIT BOARD RECOMMENDATIONS PARAMETER VALUE Pad Size on PCB 0.275mm Pad Shape Round Pad Definition Non-Solder Mask defined pads Solder Mask Opening 0.325mm Round Solder Stencil Thickness 0.125 - 0.150mm Solder Stencil Aperture Opening (laser cut, 5% tapered walls) 0.330mm Round Solder Flux Ratio 50/50 by volume Solder Paste Type No Clean Pad Protective Finish OSP (Entek Cu Plus 106A) Tolerance — Edge To Corner Ball +50µm Solder Ball Side Coplanarity +20µm Maximum Dwell Time Above Liquidous 60 seconds Soldering Maximum Temperature 260°C Non-Solder Mask Defined Pad 0.275mm DIA. Solder Stencil Opening 0.330mm DIA. Solder Mask Opening 0.325mm DIA. Figure 3. Recommended Non-Solder Mask Defined Pad Illustration Temperature (°C) 250 200 150 100 50 0 Figure 4. Eutectic (SnPb) Solder Ball Reflow Profile 1:00.0 2:00.0 3:00.0 Time (minutes) 4:00.0 Figure 5. Lead-free (SnAgCu) Solder Ball Reflow Profile © 2003 California Micro Devices Corp. All rights reserved. 10/09/03 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 ▲ Tel: 408.263.3214 ▲ Fax: 408.263.7846 ▲ www.calmicro.com 5 CSPEMI201A Mechanical Details CSP Mechanical Specifications Mechanical Package Diagrams CSPEMI201A devices are packaged in a custom Chip Scale Package (CSP). Dimensions are presented below. For complete information on CSP packaging, see the California Micro Devices CSP Package Information document. BOTTOM VIEW A1 C B 5 A Millimeters Inches Nom Max A1 0.905 0.950 0.995 0.0356 0.0374 0.0392 A2 1.365 1.410 1.455 0.0537 0.0555 0.0573 B1 0.495 0.500 0.505 0.0195 0.0197 0.0199 B2 0.245 0.250 0.255 0.0096 0.0098 0.0100 B3 0.430 0.435 0.440 0.0169 0.0171 0.0173 B4 0.430 0.435 0.440 0.0169 0.0171 0.0173 C1 0.175 0.225 0.275 0.0069 0.0089 0.0108 C2 0.220 0.270 0.320 0.0087 0.0106 0.0126 D1 0.561 0.605 0.649 0.0221 0.0238 0.0255 D2 0.355 0.380 0.405 C2 Nom 1 2 3 Min # per tape and reel Min A2 Custom CSP Bumps Dim B4 B3 PACKAGE DIMENSIONS Package SIDE VIEW C1 B2 B1 Max D1 0.30 DIA. D2 63/37 Sn/Pb (Eutectic) or 96.8/2.6/0.6 Sn/Ag/Cu (Lead-free) SOLDER BUMPS DIMENSIONS IN MILLIMETERS Package Dimensions for CSPEMI201A Chip Scale Package 0.0140 0.0150 0.0159 3500 pieces Controlling dimension: millimeters CSP Tape and Reel Specifications PART NUMBER CHIP SIZE (mm) POCKET SIZE (mm) B0 X A0 X K0 TAPE WIDTH W REEL DIAMETER QTY PER REEL P0 P1 CSPEMI201A 1.41 X 0.95 X 0.6 1.52 X 1.07 X 0.72 8mm 178mm (7") 3500 4mm 4mm Po Top Cover Tape 10 Pitches Cumulative Tolerance On Tape ±0.2 mm Ao W Bo Ko For Tape Feeder Reference Only including Draft. Concentric Around B. Embossment P1 Center Lines of Cavity User Direction of Feed Figure 6. Tape and Reel Mechanical Data © 2003 California Micro Devices Corp. All rights reserved. 6 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 ▲ Tel: 408.263.3214 ▲ Fax: 408.263.7846 ▲ www.calmicro.com 10/09/03