TPS2202AI DUAL-SLOT PC CARD POWER-INTERFACE SWITCH WITH RESET FOR SERIAL PCMCIA CONTROLLER SLVS123A – SEPTEMBER 1995 – REVISED JUNE 1998 D D D D D D D D D D D Fully Integrated VCC and Vpp Switching for Dual-Slot PC Card Interface P2C 3-Lead Serial Interface Compatible With CardBus Controllers Meets PC Card Standards RESET Allows System Initialization of PC Cards 12-V Supply Can Be Disabled Except During 12-V Flash Programming Short Circuit and Thermal Protection Space-Saving 30-Pin SSOP (DB) Package Compatible With 3.3-V, 5-V and 12-V PC Cards Power Saving IDD = 83 µA Typ, IQ = 1 µA Low rDS(on) (160-mΩ VCC Switch) Break-Before-Make Switching DB OR DF PACKAGE (TOP VIEW) 5V 5V DATA CLOCK LATCH RESET 12V AVPP AVCC AVCC AVCC GND APWR_GOOD RESET 3.3V 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 5V NC NC NC NC VDD 12V BVPP BVCC BVCC BVCC BPWR_GOOD OC 3.3V 3.3V NC – No internal connection description The TPS2202AI PC Card power-interface switch provides an integrated power-management solution for two PC Cards. All of the discrete power MOSFETs, a logic section, current limiting, thermal protection, and power-good reporting for PC Card control are combined on a single integrated circuit (IC), using the Texas Instruments LinBiCMOS process. The circuit allows the distribution of 3.3-V, 5-V, and/or 12-V card power by means of the P2C (PCMCIA Peripheral-Control) Texas Instruments nonproprietary serial interface. The current-limiting feature eliminates the need for fuses, which reduces component count and improves reliability. Current-limit reporting can help the user isolate a system fault to a specific card. The TPS2202AI incorporates a reset function, selectable by one of two inputs, to help alleviate system errors. The reset function enables PC Card initialization concurrent with host platform initialization, allowing a system reset. Reset is accomplished by grounding the VCC and Vpp (flash-memory programming voltage) outputs, which discharges residual card voltage. End equipment for the TPS2202AI includes notebook computers, desktop computers, personal digital assistants (PDAs), digital cameras, handiterminals, and bar-code scanners. The TPS2202AI is only available taped and reeled (either TPS2202AIDFLE or TPS2202AIDBLE). Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. LinBiCMOS and P2C are trademarks of Texas Instruments Incorporated. PC Card and CardBus are trademarks of PCMCIA (Personal Computer Memory Card International Association). Copyright 1998, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443 • 1 TPS2202AI DUAL-SLOT PC CARD POWER-INTERFACE SWITCH WITH RESET FOR SERIAL PCMCIA CONTROLLER SLVS123A – SEPTEMBER 1995 – REVISED JUNE 1998 typical PC card power-distribution application VDD Power Supply 12V 5V 3.3V 12 V 5V 3.3 V TPS2202AI AVPP AVCC AVCC RESET RESET Supervisor 3 PC Card A Vpp1 Vpp2 VCC VCC PC Card B AVCC Serial Interface APWR_GOOD BPWR_GOOD OC PCMCIA Controller Vpp1 Vpp2 VCC VCC BVPP BVCC BVCC BVCC Terminal Functions TERMINAL NAME 3.3V 5V 12V NO. I/O DESCRIPTION 15, 16, 17 I 3.3-V VCC input for card power 1, 2, 30 I 5-V VCC input for card power 7, 24 I 12-V Vpp input for card power AVCC 9, 10, 11 O Switched output that delivers 3.3 V, 5 V, low or high impedance to card AVPP 8 O Switched output that delivers 3.3 V, 5 V, 12 V, low or high impedance to card APWR_GOOD 13 O Logic-level power-ready output that stays low as long as AVPP is within limits BVCC 20, 21, 22 O Switched output that delivers 3.3 V, 5 V, low or high impedance BVPP 23 O Switched output that delivers 3.3 V, 5 V, 12 V, low or high impedance BPWR_GOOD 19 O Logic-level power-ready output that remains low as long as BVPP is within limits 4 I Logic-level clock for serial data word DATA 3 I Logic-level serial data word GND 12 CLOCK LATCH 5 NC 26, 27, 28, 29 OC Ground I Logic-level latch for serial data word No internal connection 18 O Logic-level overcurrent reporting output that goes low when an overcurrent condition exists RESET 6 I Logic-level RESET input active high. Do not connect if terminal 14 is used. RESET 14 I Logic-level RESET input active low. Do not connect if terminal 6 is used. VDD 25 I 5-V power to chip 2 • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443 • TPS2202AI DUAL-SLOT PC CARD POWER-INTERFACE SWITCH WITH RESET FOR SERIAL PCMCIA CONTROLLER SLVS123A – SEPTEMBER 1995 – REVISED JUNE 1998 absolute maximum ratings over operating free-air temperature (unless otherwise noted)† Supply voltage range, VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to 7 V Input voltage range for card power: VI(5V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to 7 V VI(3.3V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to VI(5V) VI(12V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to 14 V Logic input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to 7 V Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Output current (each card): IO(xVCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . internally limited IO(xVPP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . internally limited Operating virtual junction temperature range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 150°C Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 85°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 55°C to 150°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. PACKAGE DF DISSIPATION RATING TABLE TA ≤ 25°C DERATING FACTOR‡ TA = 70°C POWER RATING POWER RATING ABOVE TA = 25°C 1158 mW 9.26 mW/°C 741 mW TA = 85°C POWER RATING 602 mW DB 1024 mW 8.2 mW/°C 655 mW 532 mW ‡ These devices are mounted on an FR4 board with no special thermal considerations. recommended operating conditions Supply voltage, VDD Input voltage range, VI Output current MIN MAX UNIT 4.75 5.25 V V VI(5V) VI(3.3V) 0 0 5.25 VI(5V)§ VI(12V) IO(xVCC) at 25°C 0 13.5 V 1 A IO(xVPP) at 25°C Clock frequency Operating virtual junction temperature, TJ § VI(3.3V) should not be taken above VI(5V). • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443 • V 150 mA 0 2.5 MHz – 40 125 °C 3 TPS2202AI DUAL-SLOT PC CARD POWER-INTERFACE SWITCH WITH RESET FOR SERIAL PCMCIA CONTROLLER SLVS123A – SEPTEMBER 1995 – REVISED JUNE 1998 electrical characteristics, TA = 25°C, VDD = 5 V (unless otherwise noted) dc characteristics PARAMETER Switch resistances† VO(xVPP) VO(xVCC) Ilkg lk II TEST CONDITIONS MIN TYP 160 3.3 V to xVCC 225 5 V to xVPP 6 3.3 V to xVPP 6 12 V to xVPP 1 Clamp low voltage Ipp at 10 mA ICC at 10 mA Clamp low voltage Ipp High-impedance g state TA = 25°C TA = 85°C 1 ICC High-impedance g state TA = 25°C TA = 85°C 1 IDD Supply current VO(AVCC) = VO(BVCC) = 5 V, VO(AVPP) = VO(BVPP) = 12 V IDD Supply current in shutdown VO(BVCC) = VO(AVCC) = VO(AVPP) = VO(BVPP) = Hi-Z Leakage current Input current MAX 5 V to xVCC Short-circuit outputcurrent limit IO(xVCC) IO(xVPP) Ω V 0.8 V 10 10 µA 50 83 10.72 12-V mode mΩ 0.8 50 Power-ready threshold, PWR_GOOD Power-ready hysteresis, PWR_GOOD UNIT 11.05 150 µA 1 µA 11.4 V 50 TJ = 85°C,, Output powered up into a short to GND mV 0.75 1.3 1.9 A 120 200 400 mA † Pulse-testing techniques are used to maintain junction temperature close to ambient temperature; thermal effects must be taken into account separately. logic section PARAMETER TEST CONDITIONS MIN Logic input current 1 Logic input high level 2 Logic input low level IO = 1 mA Logic output low level Logic input minimum pulse width VDD – 0.4 • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443 • µA V V 0.4 1 UNIT V 0.8 Logic output high level 4 MAX V µs TPS2202AI DUAL-SLOT PC CARD POWER-INTERFACE SWITCH WITH RESET FOR SERIAL PCMCIA CONTROLLER SLVS123A – SEPTEMBER 1995 – REVISED JUNE 1998 switching characteristics† PARAMETER tr tf tpd d TEST CONDITIONS MIN TYP Output rise times VO(xVCC) VO(xVPP) 1.2 Output fall times VO(xVCC) VO(xVPP) 10 Propagation delay (see Figure 1‡) 5 MAX UNIT ms 14 5.8 ms LATCH↑ to VO( VPP) O(xVPP) ton toff 18 ms 5.8 ms LATCH↑ to xVCC (3 V) ton toff 28 ms LATCH↑ to xVCC (5 V) ton toff 4 ms 30 ms † Refer to Parameter Measurement Information ‡ Propagation delays are with CL = 100 µF. • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443 • 5 TPS2202AI DUAL-SLOT PC CARD POWER-INTERFACE SWITCH WITH RESET FOR SERIAL PCMCIA CONTROLLER SLVS123A – SEPTEMBER 1995 – REVISED JUNE 1998 PARAMETER MEASUREMENT INFORMATION Vpp VCC CL CL LOAD CIRCUIT LOAD CIRCUIT VDD LATCH VDD 50% 50% LATCH GND GND toff toff ton ton VI(12V) 90% VO(xVPP) 10% VI(5V) 90% VO(xVCC) 10% GND VOLTAGE WAVEFORMS GND VOLTAGE WAVEFORMS Figure 1. Test Circuits and Voltage Waveforms Table of Timing Diagrams FIGURE DATA Serial-Interface Timing 2 xVCC Propagation Delay and Rise Time With 1-µF Load, 3.3-V Switch 3 xVCC Propagation Delay and Fall Time With 1-µF Load, 3.3-V Switch 4 xVCC Propagation Delay and Rise Time With 100-µF Load, 3.3-V Switch 5 xVCC Propagation Delay and Fall Time With 100-µF Load, 3.3-V Switch 6 xVCC Propagation Delay and Rise Time With 1-µF Load, 5-V Switch 7 xVCC Propagation Delay and Fall Time With 1-µF Load, 5-V Switch 8 xVCC Propagation Delay and Rise Time With 100-µF Load, 5-V Switch 9 xVCC Propagation Delay and Fall Time With 100-µF Load, 5-V Switch 10 xVPP Propagation Delay and Rise Time With 1-µF Load, 12-V Switch 11 xVPP Propagation Delay and Fall Time With 1-µF Load, 12-V Switch 12 xVPP Propagation Delay and Rise Time With 100-µF Load, 12-V Switch 13 xVPP Propagation Delay and Fall Time With 100-µF Load, 12-V Switch 14 D8 D7 D6 D5 D4 D3 D2 D1 D0 LATCH CLOCK NOTE A: Data is clocked in on the positive leading edge of the clock. The latch should occur before next positive leading edge of the clock. For definition of D0 to D8, see the control logic table. Figure 2. Serial-Interface Timing 6 • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443 • TPS2202AI DUAL-SLOT PC CARD POWER-INTERFACE SWITCH WITH RESET FOR SERIAL PCMCIA CONTROLLER SLVS123A – SEPTEMBER 1995 – REVISED JUNE 1998 PARAMETER MEASUREMENT INFORMATION LATCH (2 V/div) LATCH (2 V/div) xVCC (1 V/div) 0 1 2 xVCC (1 V/div) 3 4 5 6 7 8 9 0 5 10 15 20 25 30 35 40 t – Time – ms t – Time – ms Figure 3. xVCC Propagation Delay and Rise Time With 1-µF Load, 3.3-V Switch Figure 4. xVCC Propagation Delay and Fall Time With 1-µF Load, 3.3-V Switch LATCH (2 V/div) LATCH (2 V/div) xVCC (1 V/div) xVCC (1 V/div) 0 1 2 3 45 4 5 6 7 8 9 0 5 t – Time – ms 10 15 20 25 30 35 40 45 t – Time – ms Figure 5. xVCC Propagation Delay and Rise Time With 100-µF Load, 3.3-V Switch Figure 6. xVCC Propagation Delay and Fall Time With 100-µF Load, 3.3-V Switch • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443 • 7 TPS2202AI DUAL-SLOT PC CARD POWER-INTERFACE SWITCH WITH RESET FOR SERIAL PCMCIA CONTROLLER SLVS123A – SEPTEMBER 1995 – REVISED JUNE 1998 PARAMETER MEASUREMENT INFORMATION LATCH (2 V/div) LATCH (2 V/div) xVCC (1 V/div) 0 xVCC (1 V/div) 1 2 3 4 0 5 10 15 20 25 30 35 40 45 t – Time – ms t – Time – ms Figure 7. xVCC Propagation Delay and Rise Time With 1-µF Load, 5-V Switch Figure 8. xVCC Propagation Delay and Fall Time With 1-µF Load, 5-V Switch LATCH (2 V/div) LATCH (2 V/div) xVCC (1 V/div) xVCC (1 V/div) 0 1 2 3 4 5 6 7 8 9 0 5 15 20 25 30 35 40 45 Figure 10. xVCC Propagation Delay and Fall Time With 100-µF Load, 5-V Switch Figure 9. xVCC Propagation Delay and Rise Time With 100-µF Load, 5-V Switch 8 10 t – Time – ms t – Time – ms • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443 • TPS2202AI DUAL-SLOT PC CARD POWER-INTERFACE SWITCH WITH RESET FOR SERIAL PCMCIA CONTROLLER SLVS123A – SEPTEMBER 1995 – REVISED JUNE 1998 PARAMETER MEASUREMENT INFORMATION LATCH (2 V/div) LATCH (2 V/div) xVPP (5 V/div) xVPP (5 V/div) 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 0 1 2 t – Time – ms 3 4 5 6 7 8 9 t – Time – ms Figure 11. xVPP Propagation Delay and Rise Time With 1-µF Load, 12-V Switch Figure 12. xVPP Propagation Delay and Fall Time With 1-µF Load, 12-V Switch LATCH (2 V/div) LATCH (2 V/div) xVPP (5 V/div) xVPP (5 V/div) 0 1 2 3 4 5 6 7 8 9 0 5 t – Time – ms 10 15 20 25 30 35 40 45 t – Time – ms Figure 14. xVPP Propagation Delay and Fall Time With 100-µF Load, 12-V Switch Figure 13. xVPP Propagation Delay and Rise Time With 100-µF Load, 12-V Switch • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443 • 9 TPS2202AI DUAL-SLOT PC CARD POWER-INTERFACE SWITCH WITH RESET FOR SERIAL PCMCIA CONTROLLER SLVS123A – SEPTEMBER 1995 – REVISED JUNE 1998 TYPICAL CHARACTERISTICS† Table of Graphs FIGURE IDD rDS(on) Supply current vs Junction temperature 15 Static drain-source on-state resistance, 3-V switch vs Junction temperature 16 rDS(on) Static drain-source on-state resistance, 5-V switch vs Junction temperature 17 rDS(on) Static drain-source on-state resistance, 12-V switch vs Junction temperature 18 VO(xVCC) VO(xVCC) Output voltage, 5-V switch vs Output current 19 Output voltage, 3.3-V switch vs Output current 20 xVpp Output voltage, Vpp switch vs Output current 21 ISC(xVCC) ISC(xVPP) Short-circuit current, 5-V switch vs Junction temperature 22 Short-circuit current, 12-V switch vs Junction temperature 23 SUPPLY CURRENT vs JUNCTION TEMPERATURE 100 VO(AVCC) = VO(BVCC) = 5 V VO(AVPP) = VO(BVPP) = 12 V No load I DD – Supply Current – µ A 95 90 ÁÁ ÁÁ ÁÁ 85 80 75 – 50 50 0 100 TJ – Junction Temperature – °C Figure 15 † t = pulse tested 10 • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443 • 150 TPS2202AI DUAL-SLOT PC CARD POWER-INTERFACE SWITCH WITH RESET FOR SERIAL PCMCIA CONTROLLER SLVS123A – SEPTEMBER 1995 – REVISED JUNE 1998 3.3-V SWITCH 5-V SWITCH STATIC DRAIN-SOURCE ON-STATE RESISTANCE vs JUNCTION TEMPERATURE STATIC DRAIN-SOURCE ON-STATE RESISTANCE vs JUNCTION TEMPERATURE r DS(on) – Static Drain-Source On-State Resistance – m Ω r DS(on) – Static Drain-Source On-State Resistance – m Ω TYPICAL CHARACTERISTICS† 400 350 VDD = 5 V VCC = 3.3 V 300 250 200 150 100 50 0 – 50 – 25 25 50 75 100 0 TJ – Junction Temperature – °C 125 240 VDD = 5 V VCC = 5 V 220 200 180 160 140 120 100 80 – 50 – 25 0 25 50 75 100 TJ – Junction Temperature – °C Figure 17 12-V SWITCH 5-V SWITCH STATIC DRAIN-SOURCE ON-STATE RESISTANCE vs JUNCTION TEMPERATURE OUTPUT VOLTAGE vs OUTPUT CURRENT 5.05 1700 VDD = 5 V VCC = 5 V VDD = 5 V Vpp = 12 V 5 1500 – 40°C VO(xVCC) – Output Voltage – V r DS(on) – Static Drain-Source On-State Resistance – m Ω Figure 16 125 1300 1100 900 700 500 – 50 4.95 4.9 25°C 4.85 85°C 125°C 4.8 4.75 – 25 0 25 50 75 100 0 125 0.1 TJ – Junction Temperature – °C Figure 18 0.2 0.3 0.4 0.5 0.6 IO(xVCC) – Output Current – A 0.7 Figure 19 † t = pulse tested • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443 • 11 TPS2202AI DUAL-SLOT PC CARD POWER-INTERFACE SWITCH WITH RESET FOR SERIAL PCMCIA CONTROLLER SLVS123A – SEPTEMBER 1995 – REVISED JUNE 1998 TYPICAL CHARACTERISTICS† 3-V SWITCH Vpp SWITCH OUTPUT VOLTAGE vs OUTPUT CURRENT OUTPUT VOLTAGE vs OUTPUT CURRENT 12.05 3.35 VDD = 5 V Vpp = 12 V 3.3 V0(xVPP) – Output Voltage – V VO(xVCC) – Output Voltage – V VDD = 5 V VCC = 3.3.3 V – 40°C 3.25 25°C 3.2 3.15 3.1 12 – 40°C 25°C 11.95 11.90 85°C 11.85 125°C 125°C 85°C 11.80 3.05 0 0.1 0.2 0.3 0.5 0.4 0.6 0 0.7 0.02 0.04 Figure 20 0.1 0.12 Figure 21 5-V SWITCH 12-V SWITCH SHORT-CIRCUIT CURRENT vs JUNCTION TEMPERATURE SHORT-CIRCUIT CURRENT vs JUNCTION TEMPERATURE 400 2 VDD = 5 V VCC = 5 V I SC(xVPP) – Short-Circuit Current – mA I SC(xVCC) – Short-Circuit Current – A 0.08 IO(xVPP) – Output Current – A IO(xVCC) – Output Current – A 1.5 1 0.5 – 50 0 50 100 VDD = 5 V Vpp = 12 V 350 300 250 200 150 100 – 50 150 TJ – Junction Temperature – °C Figure 22 100 0 50 TJ – Junction Temperature – °C Figure 23 † t = pulse tested 12 0.06 • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443 • 150 TPS2202AI DUAL-SLOT PC CARD POWER-INTERFACE SWITCH WITH RESET FOR SERIAL PCMCIA CONTROLLER SLVS123A – SEPTEMBER 1995 – REVISED JUNE 1998 APPLICATION INFORMATION overview PC Cards were initially introduced as a means to add EEPROM (flash memory) to portable computers with limited on-board memory. The idea of add-in cards quickly took hold; modems, wireless LANs, GPS systems, multimedia, and hard-disk versions were soon available. As the number of PC Card applications grew, the engineering community quickly recognized the need for a standard to ensure compatibility across platforms. To this end, the PCMCIA (Personal Computer Memory Card International Association) was established, comprised of members from leading computer, software, PC card, and semiconductor manufacturers. One key goal was to realize the “plug and play” concept. Cards and hosts from different vendors should be compatible and able to communicate with one another transparently. PC Card power specification System compatibility also means power compatibility. The most current set of specifications (PC Card Standard) set forth by the PCMCIA committee states that power is to be transferred between the host and the card through eight of the PC Card connector’s 68 terminals. This power interface consists of two VCC, two Vpp, and four ground terminals. Multiple VCC and ground terminals minimize connector-terminal and line resistance. The two Vpp terminals were originally specified as separate signals but are commonly tied together in the host to form a single node to minimize voltage losses. Card primary power is supplied through the VCC terminals; flash-memory programming and erase voltage is supplied through the Vpp terminals. As each terminal is rated to 0.5 A, VCC and Vpp can theoretically supply up to 1 A, assuming equal terminal resistance and no terminal failure. A conservative design would limit current to 500 mA. Some applications, however, require higher VCC currents. Disk drives, for example, may need as much as 750-mA peak current to create the initial torque necessary to spin up the platter. Vpp currents, on the other hand, are defined by flash-memory programming requirements, typically under 120 mA. future power trends The 1-A physical-terminal current alluded to in the PC Card specification has caused some host-system engineers to believe they are required to deliver 1 A within the voltage tolerance of the card. Future applications, such as RF cards, could use the extra power for their radio transmitters. The 5 W required for these cards require very robust power supplies and special cooling considerations. The limited number of host sockets that are able to support cards makes the market for these high-powered PC Cards uncertain. The vast majority of the cards require less than 600 mA continuous current, and the trend is towards even lower powered PC Cards that assure compatibility with a greater number of host systems. Recognizing the need for power derating, an ad hoc committee of the PCMCIA is currently working to limit the amount of steady-state dc current to the PC Card to something less than the currently implied 1 A. When a system is designed to support 1 A, the switch rDS(on), power-supply requirements, and PC Card cooling need to be carefully considered. designing around 1-A delivery Delivering 1 A means minimizing voltage and power losses across the PC Card power interface, which requires that designers trade off switch resistance and the cost associated with large-die (low rDS(on)) MOSFET transistors. The PC Card standard requires that 5 V ±5% or 3.3 V ±0.3 V be supplied to the card. The approximate 10% tolerance for the 3.3-V supply makes the 3.3-V rDS(on) less critical than the 5-V switch. A conservative approach is to allow 2% for voltage-regulator tolerance and 1% for etch- and pin-resistance drops, which leaves 2% (100 mV) for voltage drop at the 5-V switch and at least 6% (198 mV) for the 3.3-V switch. Calculating the rDS(on) necessary to support a 100 mV or 198 mV switch loss, using R = E/I and setting I = 1 A, the 5-V and 3.3-V switches would need to be 100 mΩ and 198 mΩ respectively. One solution would be to pay for a more expensive switch with lower rDS(on). A second, less expensive approach is to increase the headroom of the power supply–for example, to increase the 5 V supply 1.5% or to 5.075 ±2%. Working through the numbers once more, the 2% for the regulator plus 1 % for etch and terminal losses leaves 97% or 4.923 V. The allowable • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443 • 13 TPS2202AI DUAL-SLOT PC CARD POWER-INTERFACE SWITCH WITH RESET FOR SERIAL PCMCIA CONTROLLER SLVS123A – SEPTEMBER 1995 – REVISED JUNE 1998 APPLICATION INFORMATION designing around 1-A delivery (continued) voltage loss across the power distribution switch is now 4.923 V minus 4.750 V or 173 mV. Therefore, a switch with 173 mΩ or less could deliver 1 A or greater. Setting the power supply high is a common practice for delivering voltages to allow for system switch connector and etch losses. This practice has a minimal effect on overall battery life. In the example above, setting the power supply 1.5% high would only decrease a 3-hour battery life by approximately 2.7 minutes, trivial when compared with the decrease in battery life when running a 5-W PC Card. heat dissipation A greater concern in delivering 1 A or 5 W is the ability of the host to dissipate the heat generated by the PC Card. For desktop computers the solution is simpler: locate the PC Card cage such that it receives convection cooling from the forced air of the fan. Notebooks and other handheld equipment will not be able to rely on convection, but on conduction of heat away from the PC Card through the rails into the card cage. This is difficult because PC Card/card cage heat transfer is very poor. A typical design scenario would require the PC Card to be held at 60°C maximum with the host platform operating as high as 50°C. Preliminary testing reveals that a PC Card can have a 20°C rise, exceeding the 10°C differential in the example, when dissipating less than 2 W of continuous power. Sixty degrees centigrade was chosen because it is the maximum operating temperature allowable by PC Card specification. Power handling requirements and temperature rises are topics of concern and are currently being addressed by the PCMCIA committee. overcurrent and over-temperature protection PC Cards are inherently subject to damage that can result from mishandling. Host systems require protection against short-circuited cards that could lead to power supply or PCB-trace damage. Even systems sufficiently robust to withstand a short circuit would still undergo rapid battery discharge into the damaged PC Card, resulting in the rather sudden and unacceptable loss of system power. Most hosts include fuses for protection. The reliability of fused systems is poor though, as blown fuses require troubleshooting and repair, usually by the manufacturer. The TPS2202AI takes a two-pronged approach to overcurrent protection. First, instead of fuses, sense FETs monitor each of the power outputs. Excessive current generates an error signal that linearly limits the output current, preventing host damage or failure. Sense FETs, unlike sense resistors or polyfuses, have an added advantage in that they do not add to the series resistance of the switch and thus produce no additional voltage losses. Second, when an overcurrent condition is detected, the TPS2202AI asserts a signal at OC that can be monitored by the microprocessor to initiate diagnostics and/or send the user a warning message. In the event that an overcurrent condition persists, causing the IC to exceed its maximum junction temperature, thermal-protection circuitry activates, shutting down all power outputs until the device cools to within a safe operating region. 12-V supply not required Most PC Card switches use the externally supplied 12-V Vpp power for switch-gate drive and other chip functions, which requires that power be present at all times. The TPS2202AI offers considerable power savings by using an internal charge pump to generate the required higher voltages from the 5-V VDD supply; therefore, the external 12-V supply can be disabled except when needed for flash-memory functions, thereby extending battery lifetime. Do not ground the 12-V inputs when 12-V supply is not in use. Additional power savings are realized by the TPS2202AI during a software shutdown in which quiescent current drops to a maximum of 1 µA. 14 • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443 • TPS2202AI DUAL-SLOT PC CARD POWER-INTERFACE SWITCH WITH RESET FOR SERIAL PCMCIA CONTROLLER SLVS123A – SEPTEMBER 1995 – REVISED JUNE 1998 APPLICATION INFORMATION voltage transitioning requirement PC Cards, like portables, are migrating from 5 V to 3.3 V to minimize power consumption, optimize board space, and increase logic speeds. The TPS2202AI is designed to meet all combinations of power delivery as currently defined in the PCMCIA standard. The latest protocol accommodates mixed 3.3-V/5-V systems by first powering the card with 5 V, then polling it to determine its 3.3-V compatibility. The PCMCIA specification requires that the capacitors on 3.3-V-compatible cards be discharged to below 0.8 V before applying 3.3-V power. This ensures that sensitive 3.3-V circuitry is not subjected to any residual 5-V charge and functions as a power reset. The TPS2202AI offers a selectable VCC and Vpp ground state, in accordance with PCMCIA 3.3-V/5-V switching specifications, to fully discharge the card capacitors while switching between VCC voltages. output ground switches Several PCMCIA power-distribution switches on the market do not have an active-grounding FET switch. These devices do not meet the PC Card specification requiring a discharge of VCC within 100 ms. PC Card resistance can not be relied on to provide a discharge path for voltages stored on PC Card capacitance because of possible high-impedance isolation by power-management schemes. A method commonly shown to alleviate this problem is to add to the switch output an external 100 kΩ resistor in parallel with the PC Card. Considering that this is the only discharge path to ground, a timing analysis will reveal that the RC time constant delays the required discharge time to more than 2 seconds. The only way to ensure timing compatibility with PC Card standards is to use a power-distribution switch that has an internal ground switch, like that of the TPS22xx family, or add an external ground FET to each of the output lines with the control logic necessary to select it. In summary, the TPS2202AI is a complete single-chip dual-slot PC Card power interface. It meets all currently defined PCMCIA specifications for power delivery in 5-V, 3.3-V, and mixed systems, and offers a serial controller interface. The TPS2202AI offers functionality, power savings, overcurrent and thermal protection, and fault reporting in one 30-pin SSOP surface-mount package for maximum value added to new portable designs. power supply considerations The TPS2202AI has multiple pins for each of its 3.3-V, 5-V, and 12-V power inputs and for the switched VCC outputs. Any individual pin can conduct the rated input or output current. Unless all pins are connected in parallel, the series resistance is significantly higher than that specified, resulting in increased voltage drops and lost power. Both 12-V inputs must be connected for proper Vpp switching; it is recommended that all input and output power pins be paralleled for optimum operation. The VDD input lead must be connected to the 5-V input leads. Although the TPS2202AI is fairly immune to power input fluctuations and noise, it is generally considered good design practice to bypass power supplies typically with a 1-µF electrolytic or tantalum capacitor paralleled by a 0.047-µF to 0.1-µF ceramic capacitor. It is strongly recommended that the switched VCC and Vpp outputs be bypassed with a 0.1-µF or larger capacitor; doing so improves the immunity of the TPS2202AI to electrostatic discharge (ESD). Care should be taken to minimize the inductance of PCB traces between the TPS2202AI and the load. High switching currents can produce large negative-voltage transients, which forward biases substrate diodes, resulting in unpredictable performance. The TPS2202AI, unlike other PC Card power-interface switches, does not use the 12-V power supply for switching or other chip functions. Instead, an internal charge pump generates the necessary voltage from VDD, allowing the 12-V input supply to be shut down except when the Vpp programming or erase voltage is needed. Careful system design using this feature reduces power consumption and extends battery lifetime. The 3.3-V power input should not be taken higher than the 5-V input. Though doing so is nondestructive, this results in high current flow into the device and could result in abnormal operation. In any case, this occurrence indicates a malfunction of one input voltage or both which should be investigated. Similarly, no pin should be taken below – 0.3 V; forward biasing the parasitic-substrate diode results in substrate currents and unpredictable performance. • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443 • 15 TPS2202AI DUAL-SLOT PC CARD POWER-INTERFACE SWITCH WITH RESET FOR SERIAL PCMCIA CONTROLLER SLVS123A – SEPTEMBER 1995 – REVISED JUNE 1998 APPLICATION INFORMATION RESET or RESET inputs To ensure that cards are in a known state after power brownouts or system initialization, the PC Cards should be reset at the same time as the host by applying a low impedance to the VCC and Vpp terminals. A low-impedance output state allows discharging of residual voltage remaining on PC Card filter capacitance, permitting the system (host and PC Cards) to be powered up concurrently. The RESET or RESET input will close internal switches S1, S4, S7, and S10 with all other switches left open (see TPS2202AI control-logic table). The TPS2202AI remains in the low-impedance output state until the signal is deasserted and further data is clocked in and latched. RESET or RESET is provided for direct compatibility with systems that use either an active-low or active-high reset voltage supervisor. The unused pin is internally pulled up or down and should be left unconnected. overcurrent and thermal protection The TPS2202AI uses sense FETs to check for overcurrent conditions in each of the VCC and Vpp outputs. Unlike sense resistors or polyfuses, these FETs do not add to the series resistance of the switch; therefore, voltage and power losses are reduced. Overcurrent sensing is applied to each output separately. When an overcurrent condition is detected, only the power output affected is limited; all other power outputs continue to function normally. The OC indicator, normally a logic high, is a logic low when any overcurrent condition is detected, providing for initiation of system diagnostics and/or sending a warning message to the user. During power up, the TPS2202AI controls the rise time of the VCC and Vpp outputs and limits the current into a faulty card or connector. If a short circuit is applied after power is established (e.g., hot insertion of a bad card), current is initially limited only by the impedance between the short and the power supply. In extreme cases, as much as 10 A to 15 A may flow into the short before the current limiting of the TPS2202AI engages. If the VCC or Vpp outputs are driven below ground, the TPS2202AI may latch nondestructively in an off state. Cycling power will reestablish normal operation. Overcurrent limiting for the VCC outputs is designed to activate, if powered up, into a short in the range of 0.75 A to 1.9 A, typically at about 1.3 A. The Vpp outputs limit from 120 mA to 400 mA, typically around 200 mA. The protection circuitry acts by linearly limiting the current passing through the switch rather than initiating a full shutdown of the supply. Shutdown occurs only during thermal limiting. Thermal limiting prevents destruction of the IC from overheating if the package power-dissipation ratings are exceeded. Thermal limiting disables all power outputs (both A and B slots) until the device has cooled. calculating junction temperature The switch resistance, rDS(on), is dependent on the junction temperature, TJ, of the die. The junction temperature is dependent on both rDS(on) and the current through the switch. To calculate TJ, first find rDS(on) from Figures 16, 17, and 18 using an initial temperature estimate about 50°C above ambient. Then calculate the power dissipation for each switch, using the formula: P D + rDS(on) ǒS I2 Ǔ) Next, sum the power dissipation and calculate the junction temperature: T J + P D R qJA T , R A qJA + 108°CńW Compare the calculated junction temperature with the initial temperature estimate. If the temperatures are not within a few degrees of each other, recalculate using the calculated temperature as the initial estimate. 16 • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443 • TPS2202AI DUAL-SLOT PC CARD POWER-INTERFACE SWITCH WITH RESET FOR SERIAL PCMCIA CONTROLLER SLVS123A – SEPTEMBER 1995 – REVISED JUNE 1998 APPLICATION INFORMATION logic input and outputs The serial interface consists of DATA, CLOCK, and LATCH leads. The data is clocked in on the positive leading edge of the clock (see Figure 2). The 9-bit (D0 through D8) serial data word is loaded during the positive edge of the latch signal. The latch signal should occur before the next positive leading edge of the clock. The shutdown bit of the data word places all VCC and Vpp outputs in a high-impedance state and reduces chip quiescent current to 1 µA to conserve battery power. The TPS2202AI serial interface is designed to be compatible with serial-interface PCMCIA controllers and current PCMCIA and Japan Electronic Industry Development Association (JEIDA) standards. PRODUCT PREVIEW An overcurrent output (OC) is provided to indicate an overcurrent condition in any of the VCC or Vpp outputs as previously discussed. • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443 • 17 TPS2202AI DUAL-SLOT PC CARD POWER-INTERFACE SWITCH WITH RESET FOR SERIAL PCMCIA CONTROLLER SLVS123A – SEPTEMBER 1995 – REVISED JUNE 1998 APPLICATION INFORMATION TPS2202AI S7 S9 S2 3.3V S3 CS 3.3V 3.3V 17 12V 12V 10 17 11 51 20 17 21 51 VCC VCC Card B S4 S6 5V Vpp2 CS CS 5V Vpp1 9 16 S5 5V 18 52 S8 S1 15 Card A 8 S10 1 S12 30 CS VCC 22 S11 2 VCC 18 23 52 Vpp1 Vpp2 7 24 Internal Current Monitor Supervisor 6 14 RESET RESET Thermal 3 4 5 DATA CLOCK LATCH Serial Interface 25 VDD Controller 19 13 18 BPWR_GOOD APWR_GOOD GND OC 12 Figure 24. Internal Switching Matrix 18 • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443 • TPS2202AI DUAL-SLOT PC CARD POWER-INTERFACE SWITCH WITH RESET FOR SERIAL PCMCIA CONTROLLER SLVS123A – SEPTEMBER 1995 – REVISED JUNE 1998 APPLICATION INFORMATION TPS2202AI control logic AVPP CONTROL SIGNALS INTERNAL SWITCH SETTINGS D8 SHDN D0 A_VPP_PGM D1 A_VPP_VCC S7 1 0 0 1 0 1 1 1 OUTPUT S8 S9 VAVPP CLOSED OPEN OPEN 0V OPEN CLOSED OPEN VCC† 0 OPEN OPEN CLOSED VPP(12 V) 1 1 1 OPEN OPEN OPEN Hi-Z 0 X X OPEN OPEN OPEN Hi-Z BVPP CONTROL SIGNALS INTERNAL SWITCH SETTINGS D8 SHDN D4 B_VPP_PGM D5 B_VPP_VCC S10 1 0 0 1 0 1 1 1 OUTPUT S11 S12 VBVPP CLOSED OPEN OPEN 0V OPEN CLOSED OPEN VCC‡ 0 OPEN OPEN CLOSED VPP(12 V) 1 1 1 OPEN OPEN OPEN Hi-Z 0 X X OPEN OPEN OPEN Hi-Z AVCC CONTROL SIGNALS INTERNAL SWITCH SETTINGS OUTPUT D8 SHDN D3 A_VCC3 D2 A_VCC5 S1 S2 S3 VAVCC 1 0 0 CLOSED OPEN OPEN 0V 1 0 1 OPEN CLOSED OPEN 3.3 V 1 1 0 OPEN OPEN CLOSED 5V 1 1 1 CLOSED OPEN OPEN 0V 0 X X OPEN OPEN OPEN Hi-Z BVCC CONTROL SIGNALS INTERNAL SWITCH SETTINGS OUTPUT D8 SHDN D6 B_VCC3 D7 B_VCC5 S4 S5 S6 VBVCC 1 0 0 CLOSED OPEN OPEN 0V 1 0 1 OPEN CLOSED OPEN 3.3 V 1 1 0 OPEN OPEN CLOSED 5V 1 1 1 CLOSED OPEN OPEN 0V 0 X X OPEN OPEN OPEN Hi-Z † Output depends on AVCC ‡ Output depends on BVCC ESD protection All TPS2202AI inputs and outputs incorporate ESD-protection circuitry designed to withstand a 2-kV human-body-model discharge as defined in MIL-STD-883C, Method 3015. The VCC and Vpp outputs can be exposed to potentially higher discharges from the external environment through the PC Card connector. Bypassing the outputs with 0.1-µF capacitors protects the devices from discharges up to 10 kV. • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443 • 19 TPS2202AI DUAL-SLOT PC CARD POWER-INTERFACE SWITCH WITH RESET FOR SERIAL PCMCIA CONTROLLER SLVS123A – SEPTEMBER 1995 – REVISED JUNE 1998 APPLICATION INFORMATION 5V VDD AVCC 0.1 µF AVCC 12 V 12V AVCC VCC VCC Vpp1 Vpp2 12V PC Card Connector A BVCC BVCC BVCC TPS2202AI 0.1 µF Vpp1 Vpp2 AVPP 5V 0.1 µF AVPP 5V VCC VCC PC Card Connector B 5V 5V 3.3 V BVPP 0.1 µF BVPP 3.3V 3.3V DATA 3.3V DATA CLOCK CLOCK LATCH LATCH RESET RESET System Voltage Supervisor or Bus Reset PCMCIA Controller APWR_GOOD AVPPGOOD BPWR_GOOD BVPPGOOD OC To CPU GND CS Shutdown Signal From CPU Figure 25. Detailed Interconnections and Capacitor Recommendations 20 • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443 • TPS2202AI DUAL-SLOT PC CARD POWER-INTERFACE SWITCH WITH RESET FOR SERIAL PCMCIA CONTROLLER SLVS123A – SEPTEMBER 1995 – REVISED JUNE 1998 MECHANICAL DATA DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 28 PIN SHOWN 0,38 0,22 0,65 28 0,15 M 15 0,15 NOM 5,60 5,00 8,20 7,40 Gage Plane 1 14 0,25 A 0°– 8° 1,03 0,63 Seating Plane 2,00 MAX 0,10 0,05 MIN PINS ** 14 16 20 24 28 30 38 A MAX 6,50 6,50 7,50 8,50 10,50 10,50 12,90 A MIN 5,90 5,90 6,90 7,90 9,90 9,90 12,30 DIM 4040065 / D 02/98 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-150 • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443 • 21 TPS2202AI DUAL-SLOT PC CARD POWER-INTERFACE SWITCH WITH RESET FOR SERIAL PCMCIA CONTROLLER SLVS123A – SEPTEMBER 1995 – REVISED JUNE 1998 MECHANICAL DATA DF (R-PDSO-G30) PLASTIC SMALL-OUTLINE PACKAGE 0,45 0,25 0,80 30 0,12 M 16 7,80 7,20 10,80 10,00 0,15 NOM 1 15 Gage Plane 13,10 12,50 0,25 0°– 8° 0,84 0,76 Seating Plane 2,65 MAX 0,10 0,10 MIN 4040038 / B 02/95 NOTES: A. All linear dimensions are in millimeters. B. This drawing is subject to change without notice. 22 • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443 • IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 1998, Texas Instruments Incorporated