UCC27511 www.ti.com SLUSAW9B – FEBRUARY 2012 – REVISED MARCH 2012 Single Channel High-Speed, Low-Side Gate Driver (with 4-A Peak Source and 8-A Peak Sink) Check for Samples: UCC27511 FEATURES APPLICATIONS • • • • 1 • • • • • • • • • • • • • • Low-Cost, Gate-Driver Device Offering Superior Replacement of NPN and PNP Discrete Solutions 4-A Peak Source and 8-A Peak Sink Asymmetrical Drive Strong Sink Current Offers Enhanced Immunity Against Miller Turn On Split Output Configuration (allows easy and independent adjustment of turn-on and turnoff speeds) Fast Propagation Delays (13-ns typical) Fast Rise and Fall Times (9-ns and 7-ns typical) 4.5-V to 18-V Single Supply Range Outputs Held Low During VDD UVLO (ensures glitch free operation at power-up and powerdown) TTL and CMOS Compatible Input Logic Threshold, (independent of supply voltage) Hysteretic Logic Thresholds for High Noise Immunity Dual Input Design (choice of an inverting (INpin) or non-inverting (IN+ pin) driver configuration) – Unused Input Pin can be Used for Enable or Disable Function Output Held Low when Input Pins are Floating Input Pin Absolute Maximum Voltage Levels Not Restricted by VDD Pin Bias Supply Voltage Operating Temperature Range of -40°C to 140°C 6-Pin DBV Package (SOT-23) • • Switch-Mode Power Supplies DC-to-DC Converters Companion Gate Driver Devices for Digital Power Controllers Solar Power, Motor Control, UPS Gate Driver for Emerging Wide Band-Gap Power Devices (such as GaN) DESCRIPTION The UCC27511 single-channel, high-speed, low-side gate driver device is capable of effectively driving MOSFET and IGBT power switches. Using a design that inherently minimizes shoot-through current, UCC27511 is capable of sourcing and sinking high, peak-current pulses into capacitive loads offering railto-rail drive capability and extremely small propagation delay typically 13 ns. The UCC27511 provides 4-A source, 8-A sink (asymmetrical drive) peak-drive current capability. Strong sink capability in asymmetrical drive boosts immunity against parasitic, Miller turn-on effect. The UCC27511 device also features a unique split output configuration where the gate-drive current is sourced through OUTH pin and sunk through OUTL pin. This unique pin arrangement allows the user to apply independent turn-on and turn-off resistors to the OUTH and OUTL pins respectively and easily control the switching slew rates. UCC27511 is designed to operate over a wide VDD range of 4.5 V to 18 V and wide temperature range of -40°C to 140°C. Internal Under Voltage Lockout (UVLO) circuitry on VDD pin holds output low outside VDD operating range. The capability to operate at low voltage levels such as below 5 V, along with best in class switching characteristics, is especially suited for driving emerging wide band-gap power switching devices such as GaN power semiconductor devices. 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2012, Texas Instruments Incorporated UCC27511 SLUSAW9B – FEBRUARY 2012 – REVISED MARCH 2012 www.ti.com Typical Application Diagrams Non-Inverting Input Inverting Input V+ V+ VSOURCE VSOURCE C2 C2 4.5 V to 18 V 4.5 V to 18 V L1 L1 UCC27511 UCC27511 D1 IN+ 6 VDD IN+ D1 1 VOUT 6 VDD IN+ 1 VOUT Q1 Q1 R1 5 IN- OUTH R1 2 IN- 5 IN- OUTH 2 4 GND OUTL 3 + 4 GND OUTL + C1 R2 R2 3 C1 DESCRIPTION (CONT.) UCC27511 features a dual-input design which offers flexibility of implementing both inverting (IN- pin) and noninverting (IN+ pin) configuration with the same device. Either IN+ or IN- pin can be used to control the state of the driver output. The unused input pin can be used for enable/disable function. For safety purpose, internal pullup and pull-down resistors on the input pins ensure that outputs are held low when input pins are in floating condition. Hence the unused input pin cannot be left floating and needs to be properly biased to ensure that driver output is in enabled for normal operation. The input pin threshold of the UCC27511 device is based on TTL/CMOS-compatible low-voltage logic which is fixed and independent of the VDD supply voltage. Wide hysteresis between the high and low thresholds offers excellent noise immunity. This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. ORDERING INFORMATION (1) (2) (1) (2) PART NUMBER PACKAGE PEAK CURRENT (SOURCE/SINK) INPUT THRESHOLD LOGIC OPERATING TEMPERATURE RANGE, TA UCC27511DBV SOT-23 6-pin 4-A/8-A (Asymmetrical Drive) CMOS/TTL-Compatible (low voltage, independent of VDD bias voltage) -40°C to 140°C For the most current package and ordering information, see Package Option Addendum at the end of this document. All packages use Pb-Free lead finish of Pd-Ni-Au which is compatible with MSL level 1 at 255°C to 260°C peak reflow temperature to be compatible with either lead free or Sn/Pb soldering operations. DRS package is rated MSL level 2. Table 1. UCC2751x Product Family Summary PART NUMBER UCC27511DBV (1) 2 PACKAGE PEAK CURRENT (SOURCE/SINK) INPUT THRESHOLD LOGIC SOT-23, 6 pin 4-A/8-A (Asymmetrical Drive) CMOS/TTL-Compatible (low voltage, independent of VDD bias voltage) UCC27512DRS (1) 3 mm x 3 mm WSON, 6 pin UCC27516DRS (1) 3 mm x 3 mm WSON, 6 pin UCC27517DBV (1) SOT-23, 5 pin UCC27518DBV (1) SOT-23, 5 pin UCC27519DBV (1) SOT-23, 5 pin 4-A/4-A (Symmetrical Drive) CMOS (follows VDD bias voltage) Visit www.ti.com for the latest product datasheet. Copyright © 2012, Texas Instruments Incorporated UCC27511 www.ti.com SLUSAW9B – FEBRUARY 2012 – REVISED MARCH 2012 ABSOLUTE MAXIMUM RATINGS (1) (2) (3) over operating free-air temperature range (unless otherwise noted) Supply voltage range VDD MIN MAX -0.3 20 OUTH voltage -0.3 VDD + 0.3 OUTL voltage -0.3 IOUT_DC (source) 0.3 IOUT_DC (sink) 0.6 Output pulsed current (0.5 µs) (OUTH source current and OUTL sink current) IOUT_pulsed(source) 4 IOUT_pulsed(sink) 8 IN+, IN- -0.3 Human Body Model, HBM ESD 20 -40 150 Storage temperature range, TSTG -65 150 (2) (3) (4) V 500 Operating virtual junction temperature range, TJ (1) A 2000 Charged Device Model, CDM SOT23 Lead temperature V 20 Output continuous current (OUTH source current and OUTL sink current) (4) UNIT Soldering, 10 sec. 300 Reflow 260 °C Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltages are with respect to GND unless otherwise noted. Currents are positive into, negative out of the specified terminal. See Packaging Section of the datasheet for thermal limitations and considerations of packages. These devices are sensitive to electrostatic discharge; follow proper device handling procedures. Maximum voltage on input pins is not restricted by the voltage on the VDD pin. THERMAL INFORMATION UCC27511 THERMAL METRIC (1) SOT-23 (DBV) UNITS 6 PINS Junction-to-ambient thermal resistance (2) θJA (3) 217.8 θJCtop Junction-to-case (top) thermal resistance θJB Junction-to-board thermal resistance (4) 67.4 ψJT Junction-to-top characterization parameter (5) 60.4 ψJB Junction-to-board characterization parameter (6) 66.8 (1) (2) (3) (4) (5) (6) 137.7 °C/W For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953. The junction-to-ambient thermal resistance under natural convection is obtained in a simulation on a JEDEC-standard, high-K board, as specified in JESD51-7, in an environment described in JESD51-2a. The junction-to-case (top) thermal resistance is obtained by simulating a cold plate test on the package top. No specific JEDECstandard test exists, but a close description can be found in the ANSI SEMI standard G30-88. The junction-to-board thermal resistance is obtained by simulating in an environment with a ring cold plate fixture to control the PCB temperature, as described in JESD51-8. The junction-to-top characterization parameter, ψJT, estimates the junction temperature of a device in a real system and is extracted from the simulation data for obtaining θJA, using a procedure described in JESD51-2a (sections 6 and 7). The junction-to-board characterization parameter, ψJB, estimates the junction temperature of a device in a real system and is extracted from the simulation data for obtaining θJA , using a procedure described in JESD51-2a (sections 6 and 7). Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): UCC27511 3 UCC27511 SLUSAW9B – FEBRUARY 2012 – REVISED MARCH 2012 www.ti.com RECOMMENDED OPERATING CONDITIONS over operating free-air temperature range (unless otherwise noted) MIN TYP Supply voltage range, VDD 4.5 12 18 V Operating junction temperature range -40 140 °C 0 18 V Input voltage, IN+ and IN- MAX UNIT ELECTRICAL CHARACTERISTICS VDD = 12 V, TA = TJ = -40°C to 140°C, 1-µF capacitor from VDD to GND. Currents are positive into, negative out of the specified terminal. PARAMETER TEST CONDITION MIN TYP MAX IN+ = VDD, IN- = GND 40 100 160 IN+ = IN- = GND or IN+ = IN- = VDD 25 75 145 IN+ = GND, IN- = VDD 20 60 115 TA = 25°C 3.91 4.20 4.5 TA = -40°C to 140°C UNITS BIAS Currents IDD(off) Startup current VDD = 3.4 V µA Under Voltage Lockout (UVLO) VON Supply start threshold 3.70 4.20 4.65 VOFF Minimum operating voltage after supply start 3.45 3.9 4.35 VDD_H Supply voltage hysteresis 0.2 0.3 0.5 2.2 2.4 V Inputs (IN+, IN-) VIN_H Input signal high threshold Output high for IN+ pin, Output low for IN- pin VIN_L Input signal low threshold Output low for IN+ pin, Output high for IN- pin 1.0 VIN_HYS Input signal hysteresis V 1.2 1.0 Source/Sink Current ISRC/SNK Source/sink peak current (1) CLOAD = 0.22 µF, FSW = 1 kHz -4/+8 A Outputs (OUTH, OUTL, OUT) VDDVOH VOL ROH ROL (1) (2) 4 High output voltage Low output voltage Output pull-up resistance (2) Output pull-down resistance VDD = 12 V IOUTH = -10 mA 50 90 VDD = 4.5 V IOUTH = -10 mA 60 130 VDD = 12 IOUTL = 10 mA 5 6.5 VDD = 4.5 V IOUTL = 10 mA 5.5 10 VDD = 12 V IOUTH = -10 mA 5.0 7.5 VDD = 4.5 V IOUTH = -10 mA 5.0 11.0 VDD = 12 V IOUTL = 10 mA 0.375 0.650 VDD = 4.5 V IOUTL = 10 mA 0.45 0.750 mV Ω Ensured by Design. ROH represents on-resistance of P-Channel MOSFET in pull-up structure of the UCC27511's output stage. Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): UCC27511 UCC27511 www.ti.com SLUSAW9B – FEBRUARY 2012 – REVISED MARCH 2012 ELECTRICAL CHARACTERISTICS (continued) VDD = 12 V, TA = TJ = -40°C to 140°C, 1-µF capacitor from VDD to GND. Currents are positive into, negative out of the specified terminal. PARAMETER TEST CONDITION MIN TYP MAX 8 12 16 22 VDD = 12 V CLOAD = 1.8 nF, connected to OUTH and OUTL pins tied together 7 11 VDD=4.5V CLOAD = 1.8 nF 7 11 UNITS Switching Time tR VDD = 12 V CLOAD = 1.8 nF, connected to OUTH and OUTL pins tied together Rise time (3) VDD = 4.5 V CLOAD = 1.8 nF tF tD1 tD2 (3) Fall time (3) IN+ to output propagation delay (3) IN- to output propagation delay (3) VDD = 12 V 5-V input pulse CLOAD = 1.8 nF, connected to OUTH and OUTL pins tied together 4 13 23 VDD = 4.5 V 5-V input pulse CLOAD = 1.8 nF, connected to OUTH and OUTL pins tied together 4 15 26 VDD = 12 V CLOAD = 1.8 nF, connected to OUTH and OUTL pins tied together 4 13 23 VDD = 4.5 V CLOAD = 1.8 nF, connected to OUTH and OUTL pins tied together 4 19 30 ns See timing diagrams in Figure 1, Figure 2, Figure 3 and Figure 4. High INPUT (IN+ pin) Low High IN- pin Low 90% OUTPUT 10% tD1 t r tD1 tf Figure 1. Non-Inverting Configuration (PWM Input to IN+ pin (IN- pin tied to GND), Output represents OUTH and OUTL pins tied together) Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): UCC27511 5 UCC27511 SLUSAW9B – FEBRUARY 2012 – REVISED MARCH 2012 www.ti.com High INPUT (IN- pin) Low High IN+ pin Low 90% OUTPUT 10% tD2 tf tD2 tr Figure 2. Inverting Configuration (PWM input to IN- pin (IN+ pin tied to VDD), Output represents OUTH and OUTL pins tied together) High INPUT (IN- pin) Low High ENABLE (IN+ pin) Low 90% OUTPUT 10% tD1 tr tD1 tf Figure 3. Enable and Disable Function Using IN+ Pin (Enable and disable signal applied to IN+ pin, PWM input to IN- pin, Output represents OUTH and OUTL pins tied together) High INPUT (IN+ pin) Low High ENABLE (IN- pin) Low 90% OUTPUT 10% tD2 t f tD2 tr Figure 4. Enable and Disable Function Using IN- Pin (Enable and disable signal applied to IN- pin, PWM input to IN+ pin, Output represents OUTH and OUTL pins tied together) 6 Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): UCC27511 UCC27511 www.ti.com SLUSAW9B – FEBRUARY 2012 – REVISED MARCH 2012 DEVICE INFORMATION Functional Block Diagrams IN+ VDD 6 VDD 1 VDD 2 OUTH 3 OUTL 230 kW 200 kW IN- 5 VDD GND 4 UVLO SOT-23 DBV (Top View) VDD 1 6 IN+ OUTH 2 5 IN- OUTL 3 4 GND TERMINAL FUNCTIONS TERMINAL I/O FUNCTION PIN NUMBER NAME 1 VDD I Bias supply input. 2 OUTH O Sourcing current output of driver. Connect resistor between OUTH and Gate of power switching device to adjust turn-on speed. 3 OUTL O Sinking current output of driver. Connect resistor between OUTL and Gate of power switching device to adjust turn-off speed. 4 GND - Ground. All signals referenced to this pin. 5 IN- I Inverting input. When the driver is used in non-inverting configuration connect IN- to GND in order to enable output, OUT held LOW if IN- is unbiased or floating 6 IN+ I Non-inverting input. When the driver is used in inverting configuration connect IN+ to VDD in order to enable output, OUT held LOW if IN+ is unbiased or floating Table 2. Device Logic Table IN+ PIN (1) IN- PIN OUTH PIN OUTL PIN OUT (OUTH and OUTL pins tied together) L L High impedance L L L H High impedance L L H L H High impedance H H H High impedance L L x (1) Any High impedance L L Any (1) High impedance L L x x = Floating Condition Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): UCC27511 7 UCC27511 SLUSAW9B – FEBRUARY 2012 – REVISED MARCH 2012 www.ti.com TYPICAL CHARACTERISTICS START-UP CURRENT vs TEMPERATURE OPERATING SUPPLY CURRENT vs TEMPERATURE (Output Switching) 0.12 3.5 0.1 IDD (mA) Startup Current (mA) 0.11 4 IN+=Low,IN−=Low IN+=High, IN−=Low 0.09 0.08 0.07 VDD = 3.4 V 0 50 Temperature (°C) 100 2 −50 150 100 150 G013 Figure 6. SUPPLY CURRENT vs TEMPERATURE (Output in DC On/Off condition) UVLO THRESHOLD VOLTAGE vs TEMPERATURE 4.6 IN+=Low,IN−=Low IN+=High, IN−=Low UVLO Rising UVLO Falling 4.4 0.4 UVLO Threshold (V) Operating Supply Current (mA) 50 Temperature (°C) Figure 5. 0.3 0.2 4.2 4 3.8 VDD = 12 V 0.1 −50 0 50 Temperature (°C) 100 3.6 −50 150 50 Temperature (°C) 100 150 G003 Figure 7. Figure 8. INPUT THRESHOLD vs TEMPERATURE OUTPUT PULL-UP RESISTANCE vs TEMPERATURE 8 VDD = 12 V CLoad = 1.8 nF RoH Output Pull−Up Resistance (Ω) Turn−On Turn−Off 3 2.5 2 1.5 1 −50 0 G002 3.5 Input Threshold (V) 0 G001 0.5 0 50 Temperature (°C) 100 150 7 6 5 4 −50 G014 Figure 9. 8 VDD = 12 V CLoad = 500 pF fsw = 500 kHz 2.5 0.06 0.05 −50 3 VDD = 12 V Iout = 10 mA 0 50 Temperature (°C) 100 150 G004 Figure 10. Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): UCC27511 UCC27511 www.ti.com SLUSAW9B – FEBRUARY 2012 – REVISED MARCH 2012 TYPICAL CHARACTERISTICS (continued) OUTPUT PULL-DOWN RESISTANCE vs TEMPERATURE RISE TIME vs TEMPERATURE 8 VDD = 12 V CLoad = 1.8 nF ROL 0.7 7 Rise Time (ns) Output Pull−Down Resistance (Ω) 0.8 0.5 0.3 5 VDD = 12 V Iout = 10 mA 0.1 −50 0 50 Temperature (°C) 100 6 4 −50 150 150 G000 FALL TIME vs TEMPERATURE INPUT TO OUTPUT PROPAGATION DELAY vs TEMPERATURE 20 Propagation Delay (ns) Turn−On Turn−Off 9 Fall Time (ns) 100 Figure 12. VDD = 12 V CLoad = 1.8 nF 8 7 6 −50 0 50 Temperature (°C) 100 15 10 VDD = 12 V 5 −50 150 0 G000 50 Temperature (°C) 100 Figure 13. Figure 14. OPERATING SUPPLY CURRENT vs FREQUENCY PROPAGATION DELAYS vs SUPPLY VOLTAGE 20 150 G006 20 VDD=4.5V VDD=12V VDD=15V 16 18 Propagation Delay (ns) 18 Supply Current (mA) 50 Temperature (°C) Figure 11. 10 14 12 10 8 6 4 0 100 200 300 400 Frequency (kHz) 500 600 16 14 12 10 8 CLoad = 1.8 nF 2 0 0 G005 700 6 Turn−On Turn−Off 0 G010 Figure 15. 4 8 12 Supply Voltage (V) 16 20 G007 Figure 16. Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): UCC27511 9 UCC27511 SLUSAW9B – FEBRUARY 2012 – REVISED MARCH 2012 www.ti.com TYPICAL CHARACTERISTICS (continued) RISE TIME vs SUPPLY VOLTAGE FALL TIME vs SUPPLY VOLTAGE 20 10 Fall Time (ns) Rise Time (ns) 8 15 10 6 4 5 0 4 8 12 Supply Voltage (V) 16 20 2 0 G008 Figure 17. 4 8 12 Supply Voltage (V) 16 20 G009 Figure 18. APPLICATION INFORMATION Introduction High-current gate driver devices are required in switching power applications for a variety of reasons. In order to effect fast switching of power devices and reduce associated switching power losses, a powerful gate driver can be employed between the PWM output of controllers and the gates of the power semiconductor devices. Further, gate drivers are indispensable when sometimes it is just not feasible to have the PWM controller directly drive the gates of the switching devices. With advent of digital power, this situation will be often encountered since the PWM signal from the digital controller is often a 3.3-V logic signal which is not capable of effectively turning on a power switch. A level shifting circuitry is needed to boost the 3.3-V signal to the gate-drive voltage (such as 12 V) in order to fully turn on the power device and minimize conduction losses. Traditional buffer drive circuits based on NPN/PNP bipolar transistors in totem-pole arrangement, being emitter follower configurations, prove inadequate with digital power since they lack level-shifting capability. Gate drivers effectively combine both the level-shifting and buffer-drive functions. Gate drivers also find other needs such as minimizing the effect of highfrequency switching noise by locating the high-current driver physically close to the power switch, driving gatedrive transformers and controlling floating power-device gates, reducing power dissipation and thermal stress in controllers by moving gate charge power losses into itself. Finally, emerging wide band-gap power device technologies such as GaN based switches, which are capable of supporting very high switching frequency operation, are driving very special requirements in terms of gate drive capability. These requirements include operation at low VDD voltages (5 V or lower), low propagation delays and availability in compact, low-inductance packages with good thermal capability. In summary gate-driver devices are extremely important components in switching power combining benefits of high-performance, low cost, component count and board space reduction and simplified system design. 10 Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): UCC27511 UCC27511 www.ti.com SLUSAW9B – FEBRUARY 2012 – REVISED MARCH 2012 UCC2751x Product Family The UCC2751x family of gate driver products (Table 3) represent Texas Instruments’ latest generation of singlechannel, low-side high-speed gate driver devices featuring high-source/sink current capability, industry best-inclass switching characteristics and a host of other features (Table 4) all of which combine to ensure efficient, robust and reliable operation in high-frequency switching power circuits. Table 3. UCC2751x Product Family Summary PART NUMBER UCC27511DBV PEAK CURRENT (SOURCE/SINK) INPUT THRESHOLD LOGIC SOT-23, 6 pin 4-A/8-A (Asymmetrical Drive) CMOS/TTL-Compatible (low voltage, independent of VDD bias voltage) (1) 3 mm x 3 mm WSON, 6 pin UCC27516DRS (1) 3 mm x 3 mm WSON, 6 pin UCC27517DBV (1) SOT-23, 5 pin UCC27518DBV (1) SOT-23, 5 pin UCC27519DBV (1) SOT-23, 5 pin UCC27512DRS (1) PACKAGE 4-A/4-A (Symmetrical Drive) CMOS (follows VDD bias voltage) Visit www.ti.com for the latest product datasheet. Table 4. UCC2751x Features and Benefits FEATURE BENEFIT High Source/Sink Current Capability 4 A/8 A (Asymmetrical) – UCC27511/2 4 A/4 A (Symmetrical) – UCC27516/7 High current capability offers flexibility in employing UCC2751x family of devices to drive a variety of power switching devices at varying speeds Best-in-class 13-ns (typ) Propagation delay Extremely low pulse transmission distortion Expanded VDD Operating range of 4.5 V to 18 V Flexibility in system design Low VDD operation ensures compatibility with emerging wide bandgap power devices such as GaN Expanded Operating Temperature range of -40°C to 140°C (See Electrical Characteristics table) VDD UVLO Protection Outputs are held low in UVLO condition, which ensures predictable, glitch-free operation at power-up and power-down Outputs held low when input pins (INx) in floating condition Safety feature, especially useful in passing abnormal condition tests during safety certification Ability of input pins (and enable pin in UCC27518/9) to handle voltage levels not restricted by VDD pin bias voltage System simplification, especially related to auxiliary bias supply architecture Split output structure in UCC27511 (OUTH, OUTL) Allows independent optimization of turn-on and turn-off speeds Strong sink current (8 A) and low pull-down impedance (0.375 Ω) in UCC27511/2 High immunity to C x dV/dt Miller turn-on events CMOS/TTL compatible input threshold logic with wide hysteresis in UCC27511/2/6/7 Enhanced noise immunity, while retaining compatibility with microcontroller logic level input signals (3.3 V, 5 V) optimized for digital power CMOS input threshold logic in UCC27518/9 (VIN_H – 70% VDD, VIN_L – 30% VDD) Well suited for slow input voltage signals, with flexibility to program delay circuits (RCD) Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): UCC27511 11 UCC27511 SLUSAW9B – FEBRUARY 2012 – REVISED MARCH 2012 www.ti.com Typical Application Diagram Typical application diagrams of UCC27511 devices are shown below illustrating use in non-inverting and inverting driver configurations. The UCC27511 device features a unique split output configuration where the gatedrive current is sourced through OUTH pin and sunk through OUTL pin. This unique pin arrangement allows user to apply independent turn-on and turn-off resistors to the OUTH and OUTL pins respectively and easily control the turn-on and turn-off switching dV/dt. This pin arrangement, along with the low pull-down impedance of the output driver stage, is especially handy in applications where a high C x dV/dt Miller turn-on immunity is needed (such as with GaN power switches, SR MOSFETs etc) and OUTL pin can be directly tied to the gate of the power device. V+ VSOURCE C2 4.5 V to 18 V L1 UCC27511 D1 IN+ 6 VDD IN+ 1 VOUT Q1 R1 5 OUTH IN- 2 + C1 R2 4 GND OUTL 3 Figure 19. Using UCC27511 Non-Inverting Input (IN- is grounded to enable output) V+ VSOURCE C2 4.5 V to 18 V L1 UCC27511 D1 6 IN+ VDD 1 VOUT Q1 R1 IN- 5 IN- OUTH 2 + R2 4 GND OUTL C1 3 Figure 20. Using UCC27511 Inverting Input (IN+ is tied to VDD enable output) 12 Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): UCC27511 UCC27511 www.ti.com SLUSAW9B – FEBRUARY 2012 – REVISED MARCH 2012 VDD and Undervoltage Lockout The UCC2751X devices have internal Under Voltage LockOut (UVLO) protection feature on the VDD pin supply circuit blocks. Whenever the driver is in UVLO condition (i.e. when VDD voltage less than VON during power up and when VDD voltage is less than VOFF during power down), this circuit holds all outputs LOW, regardless of the status of the inputs. The UVLO is typically 4.2 V with 300-mV typical hysteresis. This hysteresis helps prevent chatter when low VDD supply voltages have noise from the power supply and also when there are droops in the VDD bias voltage when the system commences switching and there is a sudden increase in IDD. The capability to operate at low voltage levels such as below 5 V, along with best-in-class switching characteristics, is especially suited for driving emerging GaN wide bandgap power semiconductor devices. For example, at power up, the UCC2751X driver output remains LOW until the VDD voltage reaches the UVLO threshold. The magnitude of the OUT signal rises with VDD until steady-state VDD is reached. In the non-inverting operation (PWM signal applied to IN+ pin) shown below, the output remains LOW until the UVLO threshold is reached, and then the output is in-phase with the input. In the inverting operation (PWM signal applied to IN- pin) shown below the output remains LOW until the UVLO threshold is reached, and then the output is out-phase with the input. In both cases, the unused input pin must be properly biased to enable the output. It is worth noting that in these devices the output turns to high state only if IN+ pin is high and IN- pin is low after the UVLO threshold is reached. Since the driver draws current from the VDD pin to bias all internal circuits, for the best high-speed circuit performance, two VDD bypass capacitors are recommended to prevent noise problems. The use of surface mount components is highly recommended. A 0.1-μF ceramic capacitor should be located as close as possible to the VDD to GND pins of the gate driver. In addition, a larger capacitor (such as 1 μF) with relatively low ESR should be connected in parallel and close proximity, in order to help deliver the high-current peaks required by the load. The parallel combination of capacitors should present a low impedance characteristic for the expected current levels and switching frequencies in the application. VDD VDD Threshold VDD Threshold IN+ IN - IN+ IN- OUT OUT Figure 21. Power-Up (non-inverting drive) Figure 22. Power-Up (inverting drive) Operating Supply Current The UCC27511 features very low quiescent IDD currents. The typical operating supply current in Under Voltage LockOut (UVLO) state and fully-on state (under static and switching conditions) are summarized in Figure 5, Figure 6 and Figure 7. The IDD current when the device is fully on and outputs are in a static state (DC high or DC low, refer Figure 7) represents lowest quiescent IDD current when all the internal logic circuits of the device are fully operational. The total supply current is the sum of the quiescent IDD current, the average IOUT current due to switching and finally any current related to pull-up resistors on the unused input pin. For example when the inverting input pin is pulled low additional current is drawn from VDD supply through the pull-up resistors (refer to DEVICE INFORMATION for the device Block Diagram). Knowing the operating frequency (fSW) and the MOSFET gate (QG) charge at the drive voltage being used, the average IOUT current can be calculated as product of QG and fSW. A complete characterization of the IDD current as a function of switching frequency at different VDD bias voltages under 1.8-nF switching load is provided in Figure 15. The strikingly linear variation and close correlation with theoretical value of average IOUT indicates negligible shoot-through inside the gate-driver device attesting to its high-speed characteristics. Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): UCC27511 13 UCC27511 SLUSAW9B – FEBRUARY 2012 – REVISED MARCH 2012 www.ti.com Input Stage The input pins of UCC27511 device are based on a TTL/CMOS compatible input threshold logic that is independent of the VDD supply voltage. With typ high threshold = 2.2 V and typ low threshold = 1.2 V, the logic level thresholds can be conveniently driven with PWM control signals derived from 3.3-V and 5-V digital power controllers. Wider hysteresis (typ 1 V) offers enhanced noise immunity compared to traditional TTL logic implementations, where the hysteresis is typically less than 0.5 V. These devices also feature tight control of the input pin threshold voltage levels which eases system design considerations and ensures stable operation across temperature. The very low input capacitance on these pins reduces loading and increases switching speed. The device features an important safety function wherein, whenever any of the input pins are in a floating condition, the output of the respective channel is held in the low state. This is achieved using VDD pull-up resistors on all the inverting inputs (IN- pin) or GND pull-down resistors on all the non-inverting input pins (IN+ pin), (refer to DEVICE INFORMATION for the device Block Diagram). The device also features a dual input configuration with two input pins available to control the state of the output. The user has the flexibility to drive the device using either a non-inverting input pin (IN+) or an inverting input pin (IN-). The state of the output pin is dependent on the bias on both the IN+ and IN- pins. Refer to the input/output logic truth table (Table 2) and the Typical Application Diagrams, (Figure 19 and Figure 20), for additional clarification. Once an input pin has been chosen for PWM drive, the other input pin (the unused input pin) must be properly biased in order to enable the output. As mentioned earlier, the unused input pin cannot remain in a floating condition because whenever any input pin is left in a floating condition the output is disabled for safety purposes. Alternatively, the unused input pin can effectively be used to implement an enable/disable function, as explained below. • In order to drive the device in a non-inverting configuration, apply the PWM control input signal to IN+ pin. In this case, the unused input pin, IN-, must be biased low (eg. tied to GND) in order to enable the output. – Alternately, the IN- pin can be used to implement the enable/disable function using an external logic signal. OUT is disabled when IN- is biased high and OUT is enabled when IN- is biased low. • In order to drive the device in an inverting configuration, apply the PWM control input signal to IN- pin. In this case, the unused input pin, IN+, must be biased high (eg. tied to VDD) in order to enable the output. – Alternately, the IN+ pin can be used to implement the enable/disable function using an external logic signal. OUT is disabled when IN+ is biased low and OUT is enabled when IN+ is biased high. • Finally, it is worth noting that the output pin can be driven into a high state ONLY when IN+ pin is biased high and IN- input is biased low. The input stage of the driver should preferably be driven by a signal with a short rise or fall time. Caution must be exercised whenever the driver is used with slowly varying input signals, especially in situations where the device is located in a mechanical socket or PCB layout is not optimal: • High dI/dt current from the driver output coupled with board layout parasitics can cause ground bounce. Since the device features just one GND pin which may be referenced to the power ground, this may modify the differential voltage between input pins and GND and trigger an unintended change of output state. Because of fast 13-ns propagation delay, this can ultimately result in high-frequency oscillations, which increases power dissipation and poses risk of damage. • 1-V input threshold hysteresis boosts noise immunity compared to most other industry standard drivers. • In the worst case, when a slow input signal is used and PCB layout is not optimal, it may be necessary to add a small capacitor (1 nF) between input pin and ground very close to the driver device. This helps to convert the differential mode noise with respect to the input logic circuitry into common mode noise and avoid unintended change of output state. If limiting the rise or fall times to the power device is the primary goal, then an external resistance is highly recommended between the output of the driver and the power device instead of adding delays on the input signal. This external resistor has the additional benefit of reducing part of the gate charge related power dissipation in the gate driver device package and transferring it into the external resistor itself. 14 Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): UCC27511 UCC27511 www.ti.com SLUSAW9B – FEBRUARY 2012 – REVISED MARCH 2012 Enable Function As mentioned earlier, an enable/disable function can be easily implemented in UCC27511 using the unused input pin. When IN+ is pulled down to GND or IN- is pulled down to VDD, the output is disabled. Thus IN+ pin can be used like an enable pin that is based on active high logic, while IN- can be used like an enable pin that is based on active low logic. Output Stage The output stage of the UCC27511 device is illustrated in Figure 23. The UCC27511 device features a unique architecture on the output stage which delivers the highest peak source current when it is most needed during the Miller plateau region of the power switch turn-on transition (when the power switch drain/collector voltage experiences dV/dt). The device output stage features a hybrid pull-up structure using a parallel arrangement of N-Channel and P-Channel MOSFET devices. By turning on the N-Channel MOSFET during a narrow instant when the output changes state from low to high, the gate-driver device is able to deliver a brief boost in the peaksourcing current enabling fast turn on. VCC ROH RNMOS, Pull Up Input Signal Anti ShootThrough Circuitry Gate Voltage Boost OUTH OUTL Narrow Pulse at each Turn On ROL Figure 23. UCC2751X Gate Driver Output Structure The ROH parameter (see ELECTRICAL CHARACTERISTICS) is a DC measurement and it is representative of the on-resistance of the P-Channel device only, since the N-Channel device is turned on only during output change of state from low to high. Thus the effective resistance of the hybrid pull-up stage is much lower than what is represented by ROH parameter. The pull-down structure is composed of a N-Channel MOSFET only. The ROL parameter (see ELECTRICAL CHARACTERISTICS), which is also a DC measurement, is representative of true impedance of the pull-down stage in the device. In UCC27511, the effective resistance of the hybrid pull-up structure is approximately 2.7 x ROL. The UCC27511 is capable of delivering 4-A source, 8-A sink (asymmetrical drive) at VDD = 12 V. Strong sink capability in asymmetrical drive results in a very low pull-down impedance in the driver output stage which boosts immunity against parasitic, Miller turn on (C x dV/dt turn on) effect, especially where low gate-charge MOSFETs or emerging wide band-gap GaN power switches are used. An example of a situation where Miller turn on is a concern is synchronous rectification (SR). In SR application, the dV/dt occurs on MOSFET drain when the MOSFET is already held in off state by the gate driver. The current discharging the CGD Miller capacitance during this dV/dt is shunted by the pull-down stage of the driver. If the pull-down impedance is not low enough then a voltage spike can result in the VGS of the MOSFET, which can result in spurious turn-on. This phenomenon is illustrated in Figure 24. UCC27511 offers a best-in-class, 0.375-Ω (typ) pull-down impedance boosting immunity against Miller turn on. Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): UCC27511 15 UCC27511 SLUSAW9B – FEBRUARY 2012 – REVISED MARCH 2012 www.ti.com VDS VIN Miller Turn-On Spike in VGS CGD Gate Driver RG COSS ISNK OUTL VTH VGS of MOSFET ON OFF CGS VIN ROL VDS of MOSFET Figure 24. Very Low Pull-Down Impedance in UCC27511, 4-A/8-A Asymmetrical Drive (output stage mitigates Miller turn on effect) Figure 25 and Figure 26 illustrate typical switching characteristics of UCC27511. Figure 25. Typical Turn-On Waveform (VDD = 10 V, CL = 1 nF) Figure 26. Typical Turn-Off Waveform (VDD = 10 V, CL = 1 nF) The driver output voltage swings between VDD and GND providing rail-to-rail operation, thanks to the MOS output stage which delivers very low dropout. The presence of the MOSFET body diodes also offers low impedance to switching overshoots and undershoots. This means that in many cases, external Schottky diode clamps may be eliminated. The outputs of these drivers are designed to withstand 500-mA reverse current without either damage to the device or logic malfunction. 16 Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): UCC27511 UCC27511 www.ti.com SLUSAW9B – FEBRUARY 2012 – REVISED MARCH 2012 Power Dissipation Power dissipation of the gate driver has two portions as shown in equation below: PDISS = PDC + PSW (1) The DC portion of the power dissipation is PDC = IQ x VDD where IQ is the quiescent current for the driver. The quiescent current is the current consumed by the device to bias all internal circuits such as input stage, reference voltage, logic circuits, protections etc and also any current associated with switching of internal devices when the driver output changes state (such as charging and discharging of parasitic capacitances, parasitic shoot-through etc). The UCC27511 features very low quiescent currents (less than 1 mA, refer Figure 7) and contains internal logic to eliminate any shoot-through in the output driver stage. Thus the effect of the PDC on the total power dissipation within the gate driver can be safely assumed to be negligible. The power dissipated in the gate-driver package during switching (PSW) depends on the following factors: • Gate charge required of the power device (usually a function of the drive voltage VG, which is very close to input bias supply voltage VDD due to low VOH drop-out). • Switching frequency. • Use of external gate resistors. When a driver device is tested with a discrete, capacitive load it is a fairly simple matter to calculate the power that is required from the bias supply. The energy that must be transferred from the bias supply to charge the capacitor is given by: 1 EG = CLOAD VDD2 2 (2) Where CLOAD is load capacitor and VDD is bias voltage feeding the driver. There is an equal amount of energy dissipated when the capacitor is charged. This leads to a total power loss given by the following: PG = CLOAD VDD2 fSW (3) where ƒSW is the switching frequency. The switching load presented by a power MOSFET/IGBT can be converted to an equivalent capacitance by examining the gate charge required to switch the device. This gate charge includes the effects of the input capacitance plus the added charge needed to swing the drain voltage of the power device as it switches between the ON and OFF states. Most manufacturers provide specifications of typical and maximum gate charge, in nC, to switch the device under specified conditions. Using the gate charge Qg, one can determine the power that must be dissipated when charging a capacitor. This is done by using the equation, QG = CLOAD x VDD, to provide the following equation for power: PG = CLOAD VDD2 fSW = Qg VDD fSW (4) This power PG is dissipated in the resistive elements of the circuit when the MOSFET/IGBT is being turned on or off. Half of the total power is dissipated when the load capacitor is charged during turnon, and the other half is dissipated when the load capacitor is discharged during turnoff. When no external gate resistor is employed between the driver and MOSFET/IGBT, this power is completely dissipated inside the driver package. With the use of external gate-drive resistors, the power dissipation is shared between the internal resistance of driver and external gate resistor in accordance to the ratio of the resistances (more power dissipated in the higher resistance component). Based on this simplified analysis, the driver power dissipation during switching is calculated as follows: ROFF RON PSW = QG ´ VDD ´ fSW ´ ( + ) (ROFF +RGATE ) (RON +RGATE ) (5) where ROFF = ROL and RON (effective resistance of pull-up structure) = 2.7 x ROL. Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): UCC27511 17 UCC27511 SLUSAW9B – FEBRUARY 2012 – REVISED MARCH 2012 www.ti.com Low Propagation Delays The UCC27511 driver device features best-in-class input-to-output propagation delay of 13 ns (typ) at VDD = 12 V. This promises the lowest level of pulse transmission distortion available from industry standard gate driver devices for high-frequency switching applications. As seen in Figure 14, there is very little variation of the propagation delay with temperature and supply voltage as well, offering typically less than 20-ns propagation delays across the entire range of application conditions. Thermal Information The useful range of a driver is greatly affected by the drive power requirements of the load and the thermal characteristics of the package. In order for a gate driver to be useful over a particular temperature range the package must allow for the efficient removal of the heat produced while keeping the junction temperature within rated limits. The thermal metrics for the driver package is summarized in the Thermal Information section of the datasheet. For detailed information regarding the thermal information table, please refer to the Application Note from Texas Instruments entitled IC Package Thermal Metrics (Texas Instruments Literature Number SPRA953A). PCB Layout Proper PCB layout is extremely important in a high-current, fast-switching circuit to provide appropriate device operation and design robustness. The UCC27511 gate driver incorporates short-propagation delays and powerful output stages capable of delivering large current peaks with very fast rise and fall times at the gate of power switch to facilitate voltage transitions very quickly. At higher VDD voltages, the peak-current capability is even higher (4-A/8-A peak current is at VDD = 12 V). Very high di/dt can cause unacceptable ringing if the trace lengths and impedances are not well controlled. The following circuit layout guidelines are strongly recommended when designing with these high-speed drivers. • Locate the driver device as close as possible to power device in order to minimize the length of high-current traces between the output pins and the gate of the power device. • Locate the VDD bypass capacitors between VDD and GND as close as possible to the driver with minimal trace length to improve the noise filtering. These capacitors support high-peak current being drawn from VDD during turnon of power MOSFET. The use of low inductance SMD components such as chip resistors and chip capacitors is highly recommended. • The turn-on and turn-off current loop paths (driver device, power MOSFET and VDD bypass capacitor) should be minimized as much as possible in order to keep the stray inductance to a minimum. High dI/dt is established in these loops at two instances – during turn-on and turn-off transients, which will induce significant voltage transients on the output pin of the driver device and gate of the power switch. • Wherever possible parallel the source and return traces, taking advantage of flux cancellation. • Separate power traces and signal traces, such as output and input signals. • Star-point grounding is a good way to minimize noise coupling from one current loop to another. The GND of the driver should be connected to the other circuit nodes such as source of power switch, ground of PWM controller etc at one, single point. The connected paths should be as short as possible to reduce inductance and be as wide as possible to reduce resistance. • Use a ground plane to provide noise shielding. Fast rise and fall times at OUT may corrupt the input signals during transition. The ground plane must not be a conduction path for any current loop. Instead the ground plane must be connected to the star-point with one single trace to establish the ground potential. In addition to noise shielding, the ground plane can help in power dissipation as well. • In noisy environments, it may be necessary to tie the unused Input pin of UCC27511 to VDD (in case of IN+) or GND (in case of IN-) using short traces in order to ensure that the output is enabled and to prevent noise from causing malfunction in the output. REVISION HISTORY Changes from Revision A (February 2012) to Revision B • 18 Page Changed marketing status from Advanced Information to Final, (RTM date, March 2012). ................................................ 1 Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): UCC27511 PACKAGE OPTION ADDENDUM www.ti.com 24-Mar-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp UCC27511DBVR ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC27511DBVT ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM (3) Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 23-Mar-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) UCC27511DBVR SOT-23 DBV 6 3000 179.0 8.4 UCC27511DBVT SOT-23 DBV 6 250 179.0 8.4 Pack Materials-Page 1 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 3.2 3.2 1.4 4.0 8.0 Q3 3.2 3.2 1.4 4.0 8.0 Q3 PACKAGE MATERIALS INFORMATION www.ti.com 23-Mar-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) UCC27511DBVR SOT-23 DBV 6 3000 203.0 203.0 35.0 UCC27511DBVT SOT-23 DBV 6 250 203.0 203.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2012, Texas Instruments Incorporated