TI ABT18502

SN74ABT18502
SCAN TEST DEVICE
WITH 18-BIT REGISTERED BUS TRANSCEIVER
SCBS753 – FEBRUARY 2002
D
D
D
D
D
Member of the Texas Instruments
Widebus Family
UBT Transceiver Combines D-Type
Latches and D-Type Flip-Flops for
Operation in Transparent, Latched, or
Clocked Mode
Compatible With IEEE Std 1149.1-1990
(JTAG) Test Access Port (TAP) and
Boundary-Scan Architecture
Includes D-Type Flip-Flops and Control
Circuitry to Provide Multiplexed
Transmission of Stored and Real-Time Data
Two Boundary-Scan Cells (BSCs) Per I/O
for Greater Flexibility
D
SCOPE Instruction Set
– IEEE Std 1149.1-1990 Required
Instructions, Optional INTEST, and
P1149.1A CLAMP and HIGHZ
– Parallel Signature Analysis (PSA) at
Inputs With Masking Option
– Pseudorandom Pattern Generation
(PRPG) From Outputs
– Sample Inputs/Toggle Outputs (TOPSIP)
– Binary Count From Outputs
– Device Identification
– Even-Parity Opcodes
1A2
1A1
1OEAB
GND
1LEAB
1CLKAB
TDO
V CC
TMS
1CLKBA
1LEBA
1OEBA
GND
1B1
1B2
1B3
PM PACKAGE
(TOP VIEW)
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
1A3
1A4
1A5
GND
1A6
1A7
1A8
1A9
VCC
2A1
2A2
2A3
GND
2A4
2A5
2A6
1
48
2
47
3
46
4
45
5
44
6
43
7
42
8
41
9
40
10
39
11
38
12
37
13
36
14
35
15
34
16
33
1B4
1B5
1B6
GND
1B7
1B8
1B9
VCC
2B1
2B2
2B3
2B4
GND
2B5
2B6
2B7
2A7
2A8
2A9
GND
2OEAB
2LEAB
2CLKAB
TDI
VCC
TCK
2CLKBA
2LEBA
GND
2OEBA
2B9
2B8
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
SCOPE, UBT, and Widebus are trademarks of Texas Instruments.
Copyright  2002, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SN74ABT18502
SCAN TEST DEVICE
WITH 18-BIT REGISTERED BUS TRANSCEIVER
SCBS753 – FEBRUARY 2002
description
The SN74ABT18502 scan test device with an 18-bit universal bus transceiver is a member of the
Texas Instruments SCOPE  testability IC family. This family of devices supports IEEE Std 1149.1-1990
boundary scan to facilitate testing of complex circuit board assemblies. Scan access to the test circuitry is
accomplished via the four-wire test access port (TAP) interface.
In the normal mode, this device is an 18-bit universal bus transceiver that combines D-type latches and D-type
flip-flops to allow data flow in transparent, latched, or clocked modes. The device can be used either as two 9-bit
transceivers or one 18-bit transceiver. The test circuitry can be activated by the TAP to take snapshot samples
of the data appearing at the device pins or to perform a self test on the boundary test cells. Activating the TAP
in the normal mode does not affect the functional operation of the SCOPE universal bus transceivers.
Data flow in each direction is controlled by output-enable (OEAB and OEBA), latch-enable (LEAB and LEBA),
and clock (CLKAB and CLKBA) inputs. For A-to-B data flow, the device operates in the transparent mode when
LEAB is high. When LEAB is low, the A-bus data is latched while CLKAB is held at a static low or high logic level.
Otherwise, if LEAB is low, A-bus data is stored on a low-to-high transition of CLKAB. When OEAB is low, the
B outputs are active. When OEAB is high, the B outputs are in the high-impedance state. B-to-A data flow is
similar to A-to-B data flow but uses the OEBA, LEBA, and CLKBA inputs.
In the test mode, the normal operation of the SCOPE universal bus transceivers is inhibited, and the test circuitry
is enabled to observe and control the I/O boundary of the device. When enabled, the test circuitry performs
boundary scan test operations according to the protocol described in IEEE Std 1149.1-1990.
Four dedicated test pins are used to observe and control the operation of the test circuitry: test data input (TDI),
test data output (TDO), test mode select (TMS), and test clock (TCK). Additionally, the test circuitry can perform
other testing functions such as parallel signature analysis (PSA) on data inputs and pseudorandom pattern
generation (PRPG) from data outputs. All testing and scan operations are synchronized to the TAP interface.
Additional flexibility is provided in the test mode through the use of two boundary-scan cells (BSCs) for each
I/O pin. This allows independent test data to be captured and forced at either bus (A or B). A PSA/binary count
up (PSA/COUNT) instruction is also included to ease the testing of memories and other circuits where a binary
count addressing scheme is useful.
ORDERING INFORMATION
ORDERABLE
PART NUMBER
PACKAGE†
TA
TOP-SIDE
MARKING
–40°C to 85°C
LQFP – PM
Tray
SN74ABT18502PM
ABT18502
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design
guidelines are available at www.ti.com/sc/package.
FUNCTION TABLE‡
(normal mode, each register)
INPUTS
OUTPUT
B
OEAB
LEAB
CLKAB
A
L
L
L
X
L
L
↑
L
B0§
L
H
L
L
↑
H
L
H
X
L
L
L
H
X
H
H
H
X
X
X
Z
‡ A-to-B data flow is shown. B-to-A data flow is similar
but uses OEBA, LEBA, and CLKBA.
§ Output level before the indicated steady-state input
conditions were established
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN74ABT18502
SCAN TEST DEVICE
WITH 18-BIT REGISTERED BUS TRANSCEIVER
SCBS753 – FEBRUARY 2002
functional block diagram
Boundary-Scan Register (BSR)
1LEAB
1CLKAB
60
59
1OEAB 62
1LEBA 54
1CLKBA
1OEBA
55
53
One of Nine Channels
1A1
C1
C1
1D
1D
51
63
C1
1D
1B1
C1
1D
2LEAB 22
2CLKAB
2OEAB
2LEBA
2CLKBA
23
21
28
27
2OEBA 30
One of Nine Channels
2A1
C1
C1
1D
1D
40
10
C1
1D
2B1
C1
1D
Bypass Register
Boundary-Control
Register (BCR)
Identification
Register (IDR)
TDI
TMS
TCK
VCC
24
VCC
56
26
58
Instruction
Register (IR)
TDO
TAP
Controller
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SN74ABT18502
SCAN TEST DEVICE
WITH 18-BIT REGISTERED BUS TRANSCEIVER
SCBS753 – FEBRUARY 2002
Terminal Functions
PIN NAME
DESCRIPTION
GND
Ground
TCK
Test clock. One of four pins required by IEEE Std 1149.1-1990. Test operations of the device are synchronous to the test
clock. Data is captured on the rising edge of TCK and outputs change on the falling edge of TCK.
TDI
Test data input. One of four pins required by IEEE Std 1149.1-1990. TDI is the serial input for shifting data through the
instruction register (IR) or selected data register (DR). An internal pullup forces TDI to a high level if left unconnected.
TDO
Test data output. One of four pins required by IEEE Std 1149.1-1990. TDO is the serial output for shifting data through
the IR or selected DR.
TMS
Test mode select. One of four pins required by IEEE Std 1149.1-1990. The TMS input directs the device through its TAP
controller states. An internal pullup forces TMS to a high level if left unconnected.
VCC
1A1–1A9,
2A1– 2A9
Supply voltage
Normal-function A-bus I/O ports (see function table for normal-mode logic)
1B1–1B9,
2B1– 2B9
Normal-function B-bus I/O ports (see function table for normal-mode logic)
1CLKAB, 1CLKBA,
2CLKAB, 2CLKBA
Normal-function clock inputs (see function table for normal-mode logic)
1LEAB, 1LEBA,
2LEAB, 2LEBA
Normal-function latch enables (see function table for normal-mode logic)
1OEAB, 1OEBA,
2OEAB, 2OEBA
Normal-function output enables (see function table for normal-mode logic)
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN74ABT18502
SCAN TEST DEVICE
WITH 18-BIT REGISTERED BUS TRANSCEIVER
SCBS753 – FEBRUARY 2002
test architecture
Serial test information is conveyed by means of a four-wire test bus or TAP that conforms to IEEE Std
1149.1-1990. Test instructions, test data, and test control signals are all passed along this serial test bus. The
TAP controller monitors two signals from the test bus, namely TCK and TMS. The function of the TAP controller
is to extract the synchronization (TCK) and state control (TMS) signals from the test bus and generate the
appropriate on-chip control signals for the test structures in the device. Figure 1 shows the TAP controller state
diagram.
The TAP controller is fully synchronous to the TCK signal. Input data is captured on the rising edge of TCK and
output data changes on the falling edge of TCK. This scheme ensures that data to be captured is valid for fully
one-half of the TCK cycle.
The functional block diagram shows the IEEE Std 1149.1-1990 four-wire test bus and boundary-scan
architecture and the relationship between the test bus, the TAP controller, and the test registers. As illustrated,
the device contains an 8-bit instruction register (IR) and four test data registers (DRs): an 84-bit boundary-scan
register (BSR), a 21-bit boundary-control register (BCR), a 1-bit bypass register, and a 32-bit device
identification register (IDR).
Test-Logic-Reset
TMS = H
TMS = L
TMS = H
TMS = H
TMS = H
Run-Test/Idle
Select-DR-Scan
Select-IR-Scan
TMS = L
TMS = L
TMS = L
TMS = H
TMS = H
Capture-DR
Capture-IR
TMS = L
TMS = L
Shift-DR
Shift-IR
TMS = L
TMS = L
TMS = H
TMS = H
TMS = H
TMS = H
Exit1-DR
Exit1-IR
TMS = L
TMS = L
Pause-DR
Pause-IR
TMS = L
TMS = L
TMS = H
TMS = H
TMS = L
Exit2-DR
TMS = L
Exit2-IR
TMS = H
Update-DR
TMS = H
TMS = L
TMS = H
Update-IR
TMS = H
TMS = L
Figure 1. TAP Controller State Diagram
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
SN74ABT18502
SCAN TEST DEVICE
WITH 18-BIT REGISTERED BUS TRANSCEIVER
SCBS753 – FEBRUARY 2002
state diagram description
The TAP controller is a synchronous finite state machine that provides test control signals throughout the device.
The state diagram is shown in Figure 1 and is in accordance with IEEE Std 1149.1-1990. The TAP controller
proceeds through its states based on the level of TMS at the rising edge of TCK.
As illustrated, the TAP controller consists of sixteen states. There are six stable states (indicated by a looping
arrow in the state diagram) and ten unstable states. A stable state is defined as a state the TAP controller can
retain for consecutive TCK cycles. Any state that does not meet this criterion is an unstable state.
There are two main paths though the state diagram: one to access and control the selected DR and one to
access and control the IR. Only one register can be accessed at a time.
Test-Logic-Reset
The device powers up in the Test-Logic-Reset state. In the stable Test-Logic-Reset state, the test logic is reset
and is disabled so that the normal logic function of the device is performed. The IR is reset to an opcode that
selects the optional IDCODE instruction, if supported, or the BYPASS instruction. Certain DRs may also be reset
to their power-up values.
The state machine is constructed such that the TAP controller returns to the Test-Logic-Reset state in no more
than five TCK cycles if TMS is left high. TMS has an internal pullup resistor that forces it high if left unconnected
or if a board defect causes it to be open circuited.
For the SN74ABT18502, the IR is reset to the binary value 10000001, which selects the IDCODE instruction.
Each bit in the BSR is reset to logic 0 except bits 83–80, which are reset to logic 1. The BCR is reset to the binary
value 000000000000000000010, which selects the PSA test operation with no input masking.
Run-Test/Idle
The TAP controller must pass through the Run-Test/Idle state (from Test-Logic-Reset) before executing any test
operations. The Run-Test/Idle state can also be entered following DR or IR scans. Run-Test/Idle is provided as
a stable state in which the test logic may be actively running a test or can be idle.
The test operations selected by the BCR are performed while the TAP controller is in the Run-Test/Idle state.
Select-DR-Scan, Select-lR-Scan
No specific function is performed in the Select-DR-Scan and Select-lR-Scan states, and the TAP controller exits
either of these states on the next TCK cycle. These states are provided to allow the selection of either DR scan
or IR scan.
Capture-DR
When a DR scan is selected, the TAP controller must pass through the Capture-DR state. In the Capture-DR
state, the selected DR can capture a data value as specified by the current instruction. Such capture operations
occur on the rising edge of TCK upon which the TAP controller exits the Capture-DR state.
Shift-DR
Upon entry to the Shift-DR state, the DR is placed in the scan path between TDI and TDO and, on the first falling
edge of TCK, TDO goes from the high-impedance state to an active state. TDO enables to the logic level present
in the least significant bit (LSB) of the selected DR.
While in the stable Shift-DR state, data is serially shifted through the selected DR on each TCK cycle. The first
shift occurs on the first rising edge of TCK after entry to the Shift-DR state (i.e., no shifting occurs during the
TCK cycle in which the TAP controller changes from Capture-DR to Shift-DR or from Exit2-DR to Shift-DR). The
last shift occurs on the rising edge of TCK upon which the TAP controller exits the Shift-DR state.
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN74ABT18502
SCAN TEST DEVICE
WITH 18-BIT REGISTERED BUS TRANSCEIVER
SCBS753 – FEBRUARY 2002
Exit1-DR, Exit2-DR
The Exit1-DR and Exit2-DR states are temporary states used to end a DR scan. It is possible to return to the
Shift-DR state from either Exit1-DR or Exit2-DR without recapturing the DR.
On the first falling edge of TCK after entry to Exit1-DR, TDO goes from the active state to the high-impedance
state.
Pause-DR
No specific function is performed in the stable Pause-DR state, in which the TAP controller can remain
indefinitely. The Pause-DR state provides the capability of suspending and resuming DR scan operations
without loss of data.
Update-DR
If the current instruction calls for the selected DR to be updated with current data, such update occurs on the
falling edge of TCK following entry to the Update-DR state.
Capture-IR
When an IR scan is selected, the TAP controller must pass through the Capture-IR state. In the Capture-IR state,
the IR captures its current status value. This capture operation occurs on the rising edge of TCK, upon which
the TAP controller exits the Capture-IR state.
For the SN74ABT18502, the status value loaded in the Capture-IR state is the fixed binary value 10000001.
Shift-IR
Upon entry to the Shift-IR state, the IR is placed in the scan path between TDI and TDO and, on the first falling
edge of TCK, TDO goes from the high-impedance state to an active state. TDO enables to the logic level present
in the LSB of the IR.
While in the stable Shift-IR state, instruction data is serially shifted through the IR on each TCK cycle. The first
shift occurs on the first rising edge of TCK after entry to the Shift-IR state (i.e., no shifting occurs during the TCK
cycle in which the TAP controller changes from Capture-IR to Shift-IR or from Exit2-IR to Shift-IR). The last shift
occurs on the rising edge of TCK upon which the TAP controller exits the Shift-IR state.
Exit1-IR, Exit2-IR
The Exit1-IR and Exit2-IR states are temporary states used to end an IR scan. It is possible to return to the
Shift-IR state from either Exit1-IR or Exit2-IR without recapturing the IR.
On the first falling edge of TCK after entry to Exit1-IR, TDO goes from the active state to the high-impedance
state.
Pause-IR
No specific function is performed in the stable Pause-IR state, in which the TAP controller can remain
indefinitely. The Pause-IR state provides the capability of suspending and resuming IR scan operations without
loss of data.
Update-IR
The current instruction is updated and takes effect on the falling edge of TCK following entry to the Update-IR
state.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
SN74ABT18502
SCAN TEST DEVICE
WITH 18-BIT REGISTERED BUS TRANSCEIVER
SCBS753 – FEBRUARY 2002
register overview
With the exception of the bypass register and device IDR, any test register can be thought of as a serial shift
register with a shadow latch on each bit. The bypass register and device IDR differ in that they contain only a
shift register. During the appropriate capture state (Capture-IR for the IR, Capture-DR for DRs), the shift register
may be parallel loaded from a source specified by the current instruction. During the appropriate shift state
(Shift-IR or Shift-DR), the contents of the shift register are shifted out from TDO while new contents are shifted
in at TDI. During the appropriate update state (Update-IR or Update-DR), the shadow latches are updated from
the shift register.
instruction register (IR)
The IR is eight bits long and is used to tell the device what instruction is to be executed. Information contained
in the instruction includes the mode of operation (either normal mode, in which the device performs its normal
logic function, or test mode, in which the normal logic function is inhibited or altered), the test operation to be
performed, which of the four DRs is to be selected for inclusion in the scan path during DR scans, and the source
of data to be captured into the selected DR during Capture-DR.
Table 4 lists the instructions supported by the SN74ABT18502. The even-parity feature specified for SCOPE
devices is supported in this device. Bit 7 of the instruction opcode is the parity bit. Any instructions that are
defined for SCOPE devices but are not supported by this device default to BYPASS.
During Capture-IR, the IR captures the binary value 10000001. As an instruction is shifted in, this value is shifted
out via TDO and can be inspected as verification that the IR is in the scan path. During Update-IR, the value
that has been shifted into the IR is loaded into shadow latches. At this time, the current instruction is updated
and any specified mode change takes effect. At power up or in the Test-Logic-Reset state, the IR is reset to the
binary value 10000001, which selects the IDCODE instruction. The IR order of scan is shown in Figure 2.
TDI
Bit 7
Parity
(MSB)
Bit 6
Bit 5
Bit 4
Bit 3
Figure 2. IR Order of Scan
8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
Bit 2
Bit 1
Bit 0
(LSB)
TDO
SN74ABT18502
SCAN TEST DEVICE
WITH 18-BIT REGISTERED BUS TRANSCEIVER
SCBS753 – FEBRUARY 2002
data register (DR)
boundary-scan register (BSR)
The BSR is 84 bits long. It contains one BSC for each normal-function input pin and two BSCs for each
normal-function I/O pin (one for input data and one for output data). The BSR is used 1) to store test data that
is to be applied internally to the inputs of the normal on-chip logic and/or externally to the device output pins,
and/or 2) to capture data that appears internally at the outputs of the normal on-chip logic and/or externally at
the device input pins.
The source of data to be captured into the BSR during Capture-DR is determined by the current instruction. The
contents of the BSR can change during Run-Test/Idle as determined by the current instruction. At power up or
in Test-Logic-Reset, the value of each BSC is reset to logic 0 except BSCs 83–80, which are reset to logic 1,
ensuring that these cells, which control A-port and B-port outputs are set to benign values (i.e., if test mode were
invoked, the outputs would be at high impedance state). Rest values of other BSCs should be considered
indeterminate.
The BSR order of scan is from TDI through bits 83–0 to TDO. Table 1 shows the BSR bits and their associated
device pin signals.
Table 1. BSR Configuration
BSR BIT
NUMBER
DEVICE
SIGNAL
BSR BIT
NUMBER
DEVICE
SIGNAL
BSR BIT
NUMBER
DEVICE
SIGNAL
BSR BIT
NUMBER
DEVICE
SIGNAL
BSR BIT
NUMBER
DEVICE
SIGNAL
83
2OEAB
71
2A9-I
53
2A9-O
35
2B9-I
17
2B9-O
82
1OEAB
70
2A8-I
52
2A8-O
34
2B8-I
16
2B8-O
81
2OEBA
69
2A7-I
51
2A7-O
33
2B7-I
15
2B7-O
80
1OEBA
68
2A6-I
50
2A6-O
32
2B6-I
14
2B6-O
79
2CLKAB
67
2A5-I
49
2A5-O
31
2B5-I
13
2B5-O
78
1CLKAB
66
2A4-I
48
2A4-O
30
2B4-I
12
2B4-O
77
2CLKBA
65
2A3-I
47
2A3-O
29
2B3-I
11
2B3-O
76
1CLKBA
64
2A2-I
46
2A2-O
28
2B2-I
10
2B2-O
75
2LEAB
63
2A1-I
45
2A1-O
27
2B1-I
9
2B1-O
74
1LEAB
62
1A9-I
44
1A9-O
26
1B9-I
8
1B9-O
73
2LEBA
61
1A8-I
43
1A8-O
25
1B8-I
7
1B8-O
72
1LEBA
60
1A7-I
42
1A7-O
24
1B7-I
6
1B7-O
––
––
59
1A6-I
41
1A6-O
23
1B6-I
5
1B6-O
––
––
58
1A5-I
40
1A5-O
22
1B5-I
4
1B5-O
––
––
57
1A4-I
39
1A4-O
21
1B4-I
3
1B4-O
––
––
56
1A3-I
38
1A3-O
20
1B3-I
2
1B3-O
––
––
55
1A2-I
37
1A2-O
19
1B2-I
1
1B2-O
––
––
54
1A1-I
36
1A1-O
18
1B1-I
0
1B1-O
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
SN74ABT18502
SCAN TEST DEVICE
WITH 18-BIT REGISTERED BUS TRANSCEIVER
SCBS753 – FEBRUARY 2002
boundary-control register (BCR)
The BCR is 21 bits long. The BCR is used in the context of the RUNT instruction to implement additional test
operations not included in the basic SCOPE instruction set. Such operations include PRPG, PSA with input
masking, and binary count up (COUNT). Table 5 shows the test operations that are decoded by the BCR.
During Capture-DR, the contents of the BCR are not changed. At power up or in Test-Logic-Reset, the BCR is
reset to the binary value 000000000000000000010, which selects the PSA test operation with no input masking.
The BCR order of scan is from TDI through bits 20–0 to TDO. Table 2 shows the BCR bits and their associated
test control signals.
Table 2. BCR Configuration
BCR BIT
NUMBER
TEST
CONTROL
SIGNAL
BCR BIT
NUMBER
TEST
CONTROL
SIGNAL
BCR BIT
NUMBER
TEST
CONTROL
SIGNAL
20
MASK2.9
11
MASK1.9
2
OPCODE2
19
MASK2.8
10
MASK1.8
1
OPCODE1
18
MASK2.7
9
MASK1.7
0
OPCODE0
17
MASK2.6
8
MASK1.6
––
––
16
MASK2.5
7
MASK1.5
––
––
15
MASK2.4
6
MASK1.4
––
––
14
MASK2.3
5
MASK1.3
––
––
13
MASK2.2
4
MASK1.2
––
––
12
MASK2.1
3
MASK1.1
––
––
bypass register
The bypass register is a 1-bit scan path that can be selected to shorten the length of the system scan path,
thereby reducing the number of bits per test pattern that must be applied to complete a test operation. During
Capture-DR, the bypass register captures a logic 0. The bypass register order of scan is shown in Figure 3.
TDI
Bit 0
TDO
Figure 3. Bypass Register Order of Scan
device identification register (IDR)
The device IDR is 32 bits long. It can be selected and read to identify the manufacturer, part number, and version
of this device.
During Capture-DR, the binary value 00000000000000000110000000101111 (0000602F, hex) is captured in
the device IDR to identify this device as the TI SN74ABT18502, version 0. The device IDR order of scan is from
TDO through bits 31–0 to TDO. Table 3 shows the device IDR bits and their significance.
10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN74ABT18502
SCAN TEST DEVICE
WITH 18-BIT REGISTERED BUS TRANSCEIVER
SCBS753 – FEBRUARY 2002
Table 3. Device IDR Configuration
IDR BIT
NUMBER
IDENTIFICATION
SIGNIFICANCE
IDR BIT
NUMBER
IDENTIFICATION
SIGNIFICANCE
IDR BIT
NUMBER
IDENTIFICATION
SIGNIFICANCE
31
VERSION3
27
PARTNUMBER15
11
30
VERSION2
26
PARTNUMBER14
10
MANUFACTURER10†
MANUFACTURER09†
29
VERSION1
25
PARTNUMBER13
9
28
VERSION0
24
PARTNUMBER12
8
––
––
23
PARTNUMBER11
7
––
––
22
PARTNUMBER10
6
––
––
21
PARTNUMBER09
5
––
––
20
PARTNUMBER08
4
––
––
19
PARTNUMBER07
3
––
––
18
PARTNUMBER06
2
––
––
17
PARTNUMBER05
1
––
––
16
PARTNUMBER04
0
MANUFACTURER00†
LOGIC1†
––
––
15
PARTNUMBER03
––
––
––
––
14
PARTNUMBER02
––
––
––
––
13
PARTNUMBER01
––
––
––
––
12
PARTNUMBER00
––
MANUFACTURER08†
MANUFACTURER07†
MANUFACTURER06†
MANUFACTURER05†
MANUFACTURER04†
MANUFACTURER03†
MANUFACTURER02†
MANUFACTURER01†
––
† Note that for TI products, bits 11– 0 of the device IDR always contains the binary value 000000101111 (02F, hex).
instruction-register (IR) opcode
The IR opcodes are shown in Table 4. The following descriptions detail the operation of each instruction.
Table 4. IR Opcodes
BINARY CODE‡
BIT 7 → BIT 0
MSB → LSB
SCOPE OPCODE
DESCRIPTION
SELECTED DR
MODE
00000000
EXTEST
Boundary scan
Boundary scan
Test
10000001
IDCODE
Identification read
Device identification
Normal
10000010
SAMPLE/PRELOAD
Sample boundary
Boundary scan
Normal
00000011
Boundary scan
Boundary scan
Test
10000100
INTEST
BYPASS§
Bypass scan
Bypass
Normal
00000101
BYPASS§
Bypass scan
Bypass
Normal
00000110
HIGHZ
Control boundary to high impedance
Bypass
Modified test
10000111
Control boundary to 1/0
Bypass
Test
10001000
CLAMP
BYPASS§
Bypass scan
Bypass
Normal
00001001
RUNT
Boundary run test
Bypass
Test
00001010
READBN
Boundary read
Boundary scan
Normal
10001011
READBT
Boundary read
Boundary scan
Test
00001100
CELLTST
Boundary self test
Boundary scan
Normal
10001101
TOPHIP
Boundary toggle outputs
Bypass
Test
10001110
SCANCN
BCR scan
Boundary control
Normal
00001111
SCANCT
BCR scan
Boundary control
Test
All others
BYPASS
Bypass scan
Bypass
Normal
‡ Bit 7 is used to maintain even parity in the 8-bit instruction.
§ The BYPASS instruction is executed in lieu of a SCOPE instruction that is not supported in the SN74ABT18502.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
SN74ABT18502
SCAN TEST DEVICE
WITH 18-BIT REGISTERED BUS TRANSCEIVER
SCBS753 – FEBRUARY 2002
boundary scan
This instruction conforms to the IEEE Std 1149.1-1990 EXTEST and INTEST instructions. The BSR is selected
in the scan path. Data appearing at the device input pins is captured in the input BSCs, while data appearing
at the outputs of the normal on-chip logic is captured in the output BSCs. Data scanned into the input BSCs is
applied to the inputs of the normal on-chip logic, while data scanned into the output BSCs is applied to the device
output pins. The device operates in the test mode.
bypass scan
This instruction conforms to the IEEE Std 1149.1-1990 BYPASS instruction. The bypass register is selected in
the scan path. A logic-0 value is captured in the bypass register during Capture-DR. The device operates in the
normal mode.
sample boundary
This instruction conforms to the IEEE Std 1149.1-1990 SAMPLE/PRELOAD instruction. The BSR is selected
in the scan path. Data appearing at the device input pins is captured in the input BSCs, while data appearing
at the outputs of the normal on-chip logic is captured in the output BSCs. The device operates in the normal
mode.
control boundary to high impedance
This instruction conforms to the IEEE Std P1149.1A HIGHZ instruction. The bypass register is selected in the
scan path. A logic-0 value is captured in the bypass register during Capture-DR. The device operates in a
modified test mode in which all device I/O pins are placed in the high-impedance state, the device input pins
remain operational, and the normal on-chip logic function is performed.
control boundary to 1/0
This instruction conforms to the IEEE Std P1149.1A CLAMP instruction. The bypass register is selected in the
scan path. A logic-0 value is captured in the bypass register during Capture-DR. Data in the input BSCs is
applied to the inputs of the normal on-chip logic, while data in the output BSCs is applied to the device output
pins. The device operates in the test mode.
boundary run test
The bypass register is selected in the scan path. A logic-0 value is captured in the bypass register during
Capture-DR. The device operates in the test mode. The test operation specified in the BCR is executed during
Run-Test/Idle. The five test operations decoded by the BCR are: sample inputs/toggle outputs (TOPSIP),
PRPG, PSA, simultaneous PSA and PRPG (PSA/PRPG), and simultaneous PSA/COUNT.
boundary read
The BSR is selected in the scan path. The value in the BSR remains unchanged during Capture-DR. This
instruction is useful for inspecting data after a PSA operation.
boundary self test
The BSR is selected in the scan path. All BSCs capture the inverse of their current values during Capture-DR.
In this way, the contents of the shadow latches can be read out to verify the integrity of both shift-register and
shadow-latch elements of the BSR. The device operates in the normal mode.
boundary toggle outputs
The bypass register is selected in the scan path. A logic-0 value is captured in the bypass register during
Capture-DR. Data in the shift-register elements of the selected output BSCs is toggled on each rising edge of
TCK in Run-Test/Idle, updated in the shadow latches, and applied to the associated device output pins on each
falling edge of TCK in Run-Test/Idle. Data in the selected input BSCs remains constant and is applied to the
inputs of the normal on-chip logic. Data appearing at the device input pins is not captured in the input BSCs.
The device operates in the test mode.
12
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN74ABT18502
SCAN TEST DEVICE
WITH 18-BIT REGISTERED BUS TRANSCEIVER
SCBS753 – FEBRUARY 2002
BCR scan
The BCR is selected in the scan path. The value in the BCR remains unchanged during Capture-DR. This
operation must be performed before a boundary-run test operation to specify which test operation is to be
executed.
BCR opcodes
The BCR opcodes are decoded from BCR bits 2–0 as shown in Table 5. The selected test operation is performed
while the RUNT instruction is executed in the Run-Test/Idle state. The following descriptions detail the operation
of each BCR instruction and illustrate the associated PSA and PRPG algorithms.
Table 5. BCR Opcodes
BINARY CODE
BIT 2 → BIT 0
MSB → LSB
DESCRIPTION
X00
Sample inputs/toggle outputs (TOPSIP)
X01
Pseudorandom pattern generation/36-bit mode (PRPG)
X10
Parallel signature analysis/36-bit mode (PSA)
011
Simultaneous PSA and PRPG/18-bit mode (PSA/PRPG)
111
Simultaneous PSA and binary count up/18-bit mode (PSA/COUNT)
In general, while the control-input BSCs (bits 83–72) are not included in the toggle, PSA, PRPG, or COUNT
algorithms, the output-enable BSCs (bits 83– 80 of the BSR) control the drive state (active or high impedance)
of the selected device output pins. These BCR instructions are only valid when both bytes of the device are
operating in one direction of data flow (that is 1OEAB ≠ 1OEBA and 2OEAB ≠ 2OEBA) and in the same direction
of data flow (that is 1OEAB = 2OEAB and 1OEBA = 2OEBA). Otherwise, the bypass instruction is operated.
PSA input masking
Bits 20–3 of the BCR are used to specify device input pins to be masked from PSA operations. Bit 20 selects
masking for device input pin 2A9 during A-to-B data flow or for device input pin 2B9 during B-to-A data flow.
Bit 3 selects masking for device input pins 1A1 or 1B1 during A-to-B or B-to-A data flow, respectively. Bits
intermediate to 20 and 3 mask corresponding device input pins in order from most significant to least significant,
as indicated in Table 2. When the mask bit that corresponds to a particular device input has a logic-1 value, the
device input pin is masked from any PSA operation, meaning that the state of the device input pin is ignored
and has no effect on the generated signature. Otherwise, when a mask bit has a logic 0 value, the corresponding
device input is not masked from the PSA operation.
sample inputs/toggle outputs (TOPSIP)
Data appearing at the selected device input pins is captured in the shift-register elements of the selected BSCs
on each rising edge of TCK. This data is updated in the shadow latches of the selected input BSCs and applied
to the inputs of the normal on-chip logic. Data in the shift-register elements of the selected output BSCs is
toggled on each rising edge of TCK, updated in the shadow latches, and applied to the associated device output
pins on each falling edge of TCK.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
SN74ABT18502
SCAN TEST DEVICE
WITH 18-BIT REGISTERED BUS TRANSCEIVER
SCBS753 – FEBRUARY 2002
pseudorandom pattern generation (PRPG)
A pseudorandom pattern is generated in the shift-register elements of the selected BSCs on each rising edge
of TCK, updated in the shadow latches, and applied to the associated device output pins on each falling edge
of TCK. This data also is updated in the shadow latches of the selected input BSCs and applied to the inputs
of the normal on-chip logic. Figures 4 and 5 show the 36-bit linear-feedback shift-register algorithms through
which the patterns are generated. An initial seed value should be scanned into the BSR before performing this
operation. A seed value of all zeroes does not produce additional patterns.
2A9-I
2A8-I
2A7-I
2A6-I
2A5-I
2A4-I
2A3-I
2A2-I
2A1-I
1A9-I
1A8-I
1A7-I
1A6-I
1A5-I
1A4-I
1A3-I
1A2-I
1A1-I
2B9-O
2B8-O
2B7-O
2B6-O
2B5-O
2B4-O
2B3-O
2B2-O
2B1-O
1B9-O
1B8-O
1B7-O
1B6-O
1B5-O
1B4-O
1B3-O
1B2-O
1B1-O
=
Figure 4. 36-Bit PRPG Configuration (1OEAB = 2OEAB = 0, 1OEBA = 2OEBA = 1)
14
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN74ABT18502
SCAN TEST DEVICE
WITH 18-BIT REGISTERED BUS TRANSCEIVER
SCBS753 – FEBRUARY 2002
2B9-I
2B8-I
2B7-I
2B6-I
2B5-I
2B4-I
2B3-I
2B2-I
2B1-I
1B9-I
1B8-I
1B7-I
1B6-I
1B5-I
1B4-I
1B3-I
1B2-I
1B1-I
2A9-O
2A8-O
2A7-O
2A6-O
2A5-O
2A4-O
2A3-O
2A2-O
2A1-O
1A9-O
1A8-O
1A7-O
1A6-O
1A5-O
1A4-O
1A3-O
1A2-O
1A1-O
=
Figure 5. 36-Bit PRPG Configuration (1OEAB = 2OEAB = 1, 1OEBA = 2OEBA = 0)
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
15
SN74ABT18502
SCAN TEST DEVICE
WITH 18-BIT REGISTERED BUS TRANSCEIVER
SCBS753 – FEBRUARY 2002
parallel signature analysis (PSA)
Data appearing at the selected device input pins is compressed into a 36-bit parallel signature in the
shift-register elements of the selected BSCs on each rising edge of TCK. This data is updated in the shadow
latches of the selected input BSCs and applied to the inputs of the normal on-chip logic. Data in the shadow
latches of the selected output BSCs remains constant and is applied to the device outputs. Figures 6 and 7 show
the 36-bit linear-feedback shift-register algorithms through which the signature is generated. An initial seed
value should be scanned into the BSR prior to performing this operation.
2A8-I
2A7-I
2A6-I
2A5-I
2A4-I
2A3-I
2A2-I
2A1-I
1A9-I
1A8-I
1A7-I
1A6-I
1A5-I
1A4-I
1A3-I
1A2-I
1A1-I
2B9-O
2B8-O
2B7-O
2B6-O
2B5-O
2B4-O
2B3-O
2B2-O
2B1-O
1B9-O
1B8-O
1B7-O
1B6-O
1B5-O
1B4-O
1B3-O
1B2-O
1B1-O
MASKX.X
2A9-I
=
=
Figure 6. 36-Bit PSA Configuration (1OEAB = 2OEAB = 0, 1OEBA = 2OEBA = 1)
16
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN74ABT18502
SCAN TEST DEVICE
WITH 18-BIT REGISTERED BUS TRANSCEIVER
SCBS753 – FEBRUARY 2002
2B8-I
2B7-I
2B6-I
2B5-I
2B4-I
2B3-I
2B2-I
2B1-I
1B9-I
1B8-I
1B7-I
1B6-I
1B5-I
1B4-I
1B3-I
1B2-I
1B1-I
2A9-O
2A8-O
2A7-O
2A6-O
2A5-O
2A4-O
2A3-O
2A2-O
2A1-O
1A9-O
1A8-O
1A7-O
1A6-O
1A5-O
1A4-O
1A3-O
1A2-O
1A1-O
MASKX.X
2B9-I
=
=
Figure 7. 36-Bit PSA Configuration (1OEAB = 2OEAB = 1, 1OEBA = 2OEBA = 0)
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
17
SN74ABT18502
SCAN TEST DEVICE
WITH 18-BIT REGISTERED BUS TRANSCEIVER
SCBS753 – FEBRUARY 2002
simultaneous PSA and PRPG (PSA/PRPG)
Data appearing at the selected device input pins is compressed into an 18-bit parallel signature in the
shift-register elements of the selected input BSCs on each rising edge of TCK. This data is updated in the
shadow latches of the selected input BSCs and applied to the inputs of the normal on-chip logic. At the same
time, an 18-bit pseudorandom pattern is generated in the shift-register elements of the selected output BSCs
on each rising edge of TCK, updated in the shadow latches, and applied to the associated device output pins
on each falling edge of TCK. Figures 8 and 9 show the 18-bit linear-feedback shift-register algorithms through
which the signature and patterns are generated. An initial seed value should be scanned into the BSR prior to
performing this operation. A seed value of all zeroes does not produce additional patterns.
2A8-I
2A7-I
2A6-I
2A5-I
2A4-I
2A3-I
2A2-I
2A1-I
1A9-I
1A8-I
1A7-I
1A6-I
1A5-I
1A4-I
1A3-I
1A2-I
1A1-I
2B9-O
2B8-O
2B7-O
2B6-O
2B5-O
2B4-O
2B3-O
2B2-O
2B1-O
1B9-O
1B8-O
1B7-O
1B6-O
1B5-O
1B4-O
1B3-O
1B2-O
1B1-O
MASKX.X
2A9-I
=
=
Figure 8. 18-Bit PSA/PRPG Configuration (1OEAB = 2OEAB = 0, 1OEBA = 2OEBA = 1)
18
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN74ABT18502
SCAN TEST DEVICE
WITH 18-BIT REGISTERED BUS TRANSCEIVER
SCBS753 – FEBRUARY 2002
2B8-I
2B7-I
2B6-I
2B5-I
2B4-I
2B3-I
2B2-I
2B1-I
1B9-I
1B8-I
1B7-I
1B6-I
1B5-I
1B4-I
1B3-I
1B2-I
1B1-I
2A9-O
2A8-O
2A7-O
2A6-O
2A5-O
2A4-O
2A3-O
2A2-O
2A1-O
1A9-O
1A8-O
1A7-O
1A6-O
1A5-O
1A4-O
1A3-O
1A2-O
1A1-O
MASKX.X
2B9-I
=
=
Figure 9. 18-Bit PSA/PRPG Configuration (1OEAB = 2OEAB = 1, 1OEBA = 2OEBA = 0)
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
19
SN74ABT18502
SCAN TEST DEVICE
WITH 18-BIT REGISTERED BUS TRANSCEIVER
SCBS753 – FEBRUARY 2002
simultaneous PSA and COUNT (PSA/COUNT)
MASKX.X
Data appearing at the selected device input pins is compressed into an 18-bit parallel signature in the
shift-register elements of the selected input BSCs on each rising edge of TCK. This data is updated in the
shadow latches of the selected input BSCs and applied to the inputs of the normal on-chip logic. At the same
time, an 18-bit binary count-up pattern is generated in the shift-register elements of the selected output BSCs
on each rising edge of TCK, updated in the shadow latches, and applied to the associated device output pins
on each falling edge of TCK. Figures 10 and 11 show the 18-bit linear-feedback shift-register algorithms through
which the signature is generated. An initial seed value should be scanned into the BSR prior to performing this
operation.
2A9-I
2A8-I
2A7-I
2A6-I
2A5-I
2A4-I
2A3-I
2A2-I
2A1-I
1A9-I
1A8-I
1A7-I
1A6-I
1A5-I
1A4-I
1A3-I
1A2-I
1A1-I
2B8-O
2B7-O
2B6-O
2B5-O
2B4-O
2B3-O
2B2-O
2B1-O
MSB
2B9-O
=
LSB
=
1B9-O
1B8-O
1B7-O
1B6-O
1B5-O
1B4-O
1B3-O
1B2-O
1B1-O
Figure 10. 18-Bit PSA/COUNT Configuration (1OEAB = 2OEAB = 0, 1OEBA = 2OEBA = 1)
20
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN74ABT18502
SCAN TEST DEVICE
WITH 18-BIT REGISTERED BUS TRANSCEIVER
MASKX.X
SCBS753 – FEBRUARY 2002
2B9-I
2B8-I
2B7-I
2B6-I
2B5-I
2B4-I
2B3-I
2B2-I
2B1-I
1B9-I
1B8-I
1B7-I
1B6-I
1B5-I
1B4-I
1B3-I
1B2-I
1B1-I
2A8-O
2A7-O
2A6-O
2A5-O
2A4-O
2A3-O
2A2-O
2A1-O
MSB
2A9-O
=
LSB
=
1A9-O
1A8-O
1A7-O
1A6-O
1A5-O
1A4-O
1A3-O
1A2-O
1A1-O
Figure 11. 18-Bit PSA/COUNT Configuration (1OEAB = 2OEAB = 1, 1OEBA = 2OEBA = 0)
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
21
SN74ABT18502
SCAN TEST DEVICE
WITH 18-BIT REGISTERED BUS TRANSCEIVER
SCBS753 – FEBRUARY 2002
timing description
All test operations of the SN74ABT18502 are synchronous to the TCK signal. Data on the TDI, TMS, and
normal-function inputs is captured on the rising edge of TCK. Data appears on the TDO and normal-function
output pins on the falling edge of TCK. The TAP controller is advanced through its states (as shown in Figure 1)
by changing the value of TMS on the falling edge of TCK and then applying a rising edge to TCK.
A simple timing example is shown in Figure 12. In this example, the TAP controller begins in the
Test-Logic-Reset state and is advanced through its states as necessary to perform one IR scan and one DR
scan. While in the Shift-IR and Shift-DR states, TDI is used to input serial data and TDO is used to output serial
data. The TAP controller then is returned to the Test-Logic-Reset state. Table 6 explains the operation of the
test circuitry during each TCK cycle.
Table 6. Explanation of Timing Example
TCK
CYCLE(S)
TAP STATE
AFTER TCK
DESCRIPTION
1
Test-Logic-Reset
TMS is changed to a logic-0 value on the falling edge of TCK to begin advancing the TAP controller toward
the desired state.
2
Run-Test/Idle
3
Select-DR-Scan
4
Select-IR-Scan
5
Capture-IR
The IR captures the 8-bit binary value 10000001 on the rising edge of TCK as the TAP controller exits the
Capture-IR state.
6
Shift-IR
TDO becomes active and TDI is made valid on the falling edge of TCK. The first bit is shifted into the TAP
on the rising edge of TCK as the TAP controller advances to the next state.
Shift-IR
One bit is shifted into the IR on each TCK rising edge. With TDI held at a logic-1 value, the 8-bit binary value
11111111 is serially scanned into the IR. At the same time, the 8-bit binary value 10000001 is serially scanned
out of the IR via TDO. In TCK cycle 13, TMS is changed to a logic-1 value to end the IR scan on the next
TCK cycle. The last bit of the instruction is shifted as the TAP controller advances from Shift-IR to Exit1-IR.
14
Exit1-IR
TDO becomes inactive (goes to the high-impedance state) on the falling edge of TCK.
15
Update-IR
16
Select-DR-Scan
17
Capture-DR
The bypass register captures a logic-0 value on the rising edge of TCK as the TAP controller exits the
Capture-DR state.
18
Shift-DR
TDO becomes active and TDI is made valid on the falling edge of TCK. The first bit is shifted into the TAP
on the rising edge of TCK as the TAP controller advances to the next state.
19–20
Shift-DR
The binary value 101 is shifted in via TDI, while the binary value 010 is shifted out via TDO.
21
Exit1-DR
TDO becomes inactive (goes to the high-impedance state) on the falling edge of TCK.
22
Update-DR
23
Select-DR-Scan
7–13
22
24
Select-IR-Scan
25
Test-Logic-Reset
The IR is updated with the new instruction (BYPASS) on the falling edge of TCK.
In general, the selected DR is updated with the new data on the falling edge of TCK.
Test operation completed
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN74ABT18502
SCAN TEST DEVICE
WITH 18-BIT REGISTERED BUS TRANSCEIVER
SCBS753 – FEBRUARY 2002
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Test-Logic-Reset
Select-IR-Scan
Select-DR-Scan
Update-DR
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
Exit1-DR
Capture-DR
Update-IR
Select-DR-Scan
ÎÎ
ÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
Exit1-IR
Shift-IR
Capture-IR
Select-IR-Scan
TAP
Controller
State
Select-DR-Scan
TDO
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
Run-Test/Idle
TDI
Test-Logic-Reset
TMS
Shift-DR
TCK
3-State (TDO) or Don’t Care (TDI)
Figure 12. Timing Example
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to 7 V
Input voltage range, VI: Except I/O ports (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to 7 V
I/O ports (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to 5.5 V
Voltage range applied to any output in the high state or power-off state, VO . . . . . . . . . . . . . . – 0.5 V to 5.5 V
Current into any output in the low state, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 mA
Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –18 mA
Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 50 mA
Continuous current through VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 576 mA
Continuous current through GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1152 mA
Package thermal impedance, θJA (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34°C/W
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The input and output negative-voltage ratings can be exceeded if the input and output clamp-current ratings are observed.
2. The package thermal impedance is calculated in accordance with JESD 51-7.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
23
SN74ABT18502
SCAN TEST DEVICE
WITH 18-BIT REGISTERED BUS TRANSCEIVER
SCBS753 – FEBRUARY 2002
recommended operating conditions (see Note 3)
MIN
MAX
4.5
5.5
UNIT
VCC
VIH
Supply voltage
VIL
VI
Low-level input voltage
IOH
IOL
High-level output current
VCC
– 32
mA
Low-level output current
64
mA
∆t /∆v
Input transition rise or fall rate
10
ns / V
High-level input voltage
2
V
0.8
Input voltage
0
V
V
V
TA
Operating free-air temperature
– 40
85
°C
NOTE 3: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
VIK
VOH
TEST CONDITIONS
VCC = 4.5 V,
VCC = 4.5 V,
II = –18 mA
IOH = – 3 mA
VCC = 5 V,
VCC = 4.5 V,
VCC = 4.5 V,
MIN
–1.2
2.5
IOH = – 3 mA
IOH = – 24 mA
3
3
2
2
IOH = – 32 mA
IOL = 48 mA
2
0.55
VCC = 4
4.5
5V
II
VCC = 5
5.5
5V
V,
VI = VCC or GND
IIH
IIL
VCC = 5.5 V,
VCC = 5.5 V,
VI = VCC
VI = GND
IOZH‡
IOZL‡
VCC = 5.5 V,
VCC = 5.5 V,
VO = 2.7 V
VO = 0.5 V
IOZPU
VCC = 0 to 2 V,
VO = 2.7 V or 0.5 V,
IOZPD
VCC = 2 V to 0,
VO = 2.7 V or 0.5 V,
Ioff
ICEX
IO§
VCC = 0,
VCC = 5.5 V,
VI or VO ≤ 4.5 V
VO = 5.5 V
Outputs high
VCC = 5.5 V,
VO = 2.5 V
∆ICC¶
Ci
Cio
VCC = 5.5 V,
IO = 0,
VI = VCC or GND
IOL = 64 mA
A or B ports
UNIT
–1.2
V
V
0.55
CLK, LE, OE, TCK
A or B ports
±1
±1
±100
±100
V
µA
TDI, TMS
10
10
µA
TDI, TMS
–150
–150
µA
50
50
µA
– 50
– 50
µA
OE = 0.8 V
± 50
± 50
µA
OE = 0.8 V
± 50
± 50
µA
±100
±450
µA
50
50
µA
–200
mA
–110
–200
Outputs high
– 50
3.5
5.5
5.5
Outputs low
33
38
38
Outputs disabled
2.9
Control inputs
A or B ports
– 50
5
5
50
50
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
mA
µA
3
pF
10
pF
Co
VO = 2.5 V or 0.5 V
TDO
8
† All typical values are at VCC = 5 V.
‡ The parameters IOZH and IOZL include the input leakage current.
§ Not more than one output should be tested at a time, and the duration of the test should not exceed one second.
¶ This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND.
24
MAX
0.55
VCC = 5.5 V, One input at 3.4 V, Other inputs at VCC or GND
VI = 2.5 V or 0.5 V
VO = 2.5 V or 0.5 V
MIN
2.5
VOL
ICC
TA = 25°C
TYP†
MAX
pF
SN74ABT18502
SCAN TEST DEVICE
WITH 18-BIT REGISTERED BUS TRANSCEIVER
SCBS753 – FEBRUARY 2002
timing requirements over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted) (normal mode) (see Figure 13)
fclock
Clock frequency
tw
Pulse duration
CLKAB or CLKBA
MHz
3.5
3.5
ns
4
CLK high
A before LEAB↓ or B before LEBA↓
Hold time
UNIT
100
LEAB or LEBA high
Setup time
th
MAX
0
CLKAB or CLKBA high or low
A before CLKAB↑ or B before CLKBA↑
tsu
MIN
CLK low
ns
3.5
2
A after CLKAB↑ or B after CLKBA↑
0
A after LEAB↓ or B after LEBA↓
2
ns
timing requirements over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted) (test mode) (see Figure 13)123
MIN
MAX
UNIT
fclock
tw
Clock frequency
TCK
0
50
MHz
Pulse duration
TCK high or low
8
A, B, CLK, LE, or OE before TCK↑
4.5
tsu
Setup time
TDI before TCK↑
7.5
TMS before TCK↑
th
td
tr
ns
ns
3
A, B, CLK, LE, or OE after TCK↑
0.5
TDI after TCK↑
0.5
TMS after TCK↑
0.5
Delay time
Power up to TCK↑
50
ns
Rise time
VCC power up
1
µs
Hold time
ns
switching characteristics over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted) (normal mode) (see Figure 13)
PARAMETER
fmax
tPLH
tPHL
tPLH
tPHL
tPLH
tPHL
tPZH
tPZL
tPHZ
tPLZ
FROM
(INPUT)
TO
(OUTPUT)
CLKAB or CLKBA
A or B
B or A
CLKAB or CLKBA
B or A
LEAB or LEBA
B or A
OEAB or OEBA
B or A
OEAB or OEBA
B or A
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
VCC = 5 V,
TA = 25°C
MIN
MAX
MIN
TYP
100
130
2
3.8
5.6
2
6
2
3.8
5.6
2
6
2.5
4.7
5.7
2.5
6
2.5
4.7
5.7
2.5
6
2.5
4.9
6.4
2.5
7
2.5
4.9
6.5
2.5
7
UNIT
MAX
100
MHz
2
4.9
6.3
2
7
2.5
5.6
7.2
2.5
8
3
6.1
7.8
3
8.8
2.5
4.8
6.5
2.5
7.3
ns
ns
ns
ns
ns
25
SN74ABT18502
SCAN TEST DEVICE
WITH 18-BIT REGISTERED BUS TRANSCEIVER
SCBS753 – FEBRUARY 2002
switching characteristics over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted) (test mode) (see Figure 13)1234
PARAMETER
fmax
tPLH
tPHL
tPLH
tPHL
tPZH
tPZL
tPZH
tPZL
tPHZ
tPLZ
tPHZ
tPLZ
26
FROM
(INPUT)
TO
(OUTPUT)
TCK
TCK↓
A or B
TCK↓
TDO
TCK↓
A or B
TCK↓
TDO
TCK↓
A or B
TCK↓
TDO
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
VCC = 5 V,
TA = 25°C
MIN
MAX
MIN
TYP
50
90
2.5
9.1
11.4
2.5
13.5
2.5
9.1
10.8
2.5
12.4
2
3.8
5.1
2
5.6
2
3.8
5.3
2
6
UNIT
MAX
50
MHz
4.5
9.5
11.5
4.5
13.4
5
10.1
12.2
5
14
2.5
4.6
5.9
2.5
6.8
3
5.2
6.8
3
7.5
4
11.6
14.3
4
16.3
3.5
11.1
13.6
3.5
15.3
3
5.3
7.2
3
7.6
3
5.2
6.8
3
7.6
ns
ns
ns
ns
ns
ns
SN74ABT18502
SCAN TEST DEVICE
WITH 18-BIT REGISTERED BUS TRANSCEIVER
SCBS753 – FEBRUARY 2002
PARAMETER MEASUREMENT INFORMATION
7V
S1
500 Ω
From Output
Under Test
Open
GND
CL = 50 pF
(see Note A)
500 Ω
TEST
S1
tPLH/tPHL
tPLZ/tPZL
tPHZ/tPZH
Open
7V
Open
LOAD CIRCUIT FOR OUTPUTS
3V
1.5 V
Timing Input
0V
tw
tsu
3V
Input
1.5 V
3V
1.5 V
Data Input
1.5 V
0V
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
3V
1.5 V
0V
tPHL
1.5 V
1.5 V
tPLH
VOH
Output
1.5 V
1.5 V
0V
1.5 V
VOL
tPLZ
Output
Waveform 1
S1 at 7 V
(see Note C)
VOL
tPHL
1.5 V
tPZL
VOH
Output
3V
Output
Control
1.5 V
tPLH
1.5 V
0V
VOLTAGE WAVEFORMS
PULSE DURATION
Input
(see Note B)
th
Output
Waveform 2
S1 at Open
(see Note C)
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
INVERTING AND NON-INVERTING OUTPUTS
1.5 V
tPZH
3.5 V
VOL + 0.3 V
VOL
tPHZ
1.5 V
VOH – 0.3 V
VOH
≈0 V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
LOW- AND HIGH-LEVEL ENABLING
NOTES: A. CL includes probe and jig capacitance.
B. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns.
C. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
D. The outputs are measured one at a time with one transition per measurement.
Figure 13. Load Circuit and Voltage Waveforms
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
27
PACKAGE OPTION ADDENDUM
www.ti.com
1-May-2006
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
SN74ABT18502PM
ACTIVE
LQFP
PM
64
160
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
SN74ABT18502PMG4
ACTIVE
LQFP
PM
64
160
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
SN74ABT18502PMR
ACTIVE
LQFP
PM
64
1000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
SN74ABT18502PMRG4
ACTIVE
LQFP
PM
64
1000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
MECHANICAL DATA
MTQF008A – JANUARY 1995 – REVISED DECEMBER 1996
PM (S-PQFP-G64)
PLASTIC QUAD FLATPACK
0,27
0,17
0,50
0,08 M
33
48
49
32
64
17
0,13 NOM
1
16
7,50 TYP
Gage Plane
10,20
SQ
9,80
12,20
SQ
11,80
0,25
0,05 MIN
0°– 7°
0,75
0,45
1,45
1,35
Seating Plane
0,08
1,60 MAX
4040152 / C 11/96
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Falls within JEDEC MS-026
May also be thermally enhanced plastic with leads connected to the die pads.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Mailing Address:
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2006, Texas Instruments Incorporated