TI MSP430F4793IPZ

MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
D
D
D
D
D
D
D
D
D
− Active Mode: TBD μA at 1 MHz, 2.2 V
− Standby Mode: TBD μA
− Off Mode (RAM Retention): TBD μA
Five Power-Saving Modes
Wake-Up From Standby Mode in Less
Than 6 μs
16-Bit RISC Architecture,
62.5-ns Instruction Cycle Time
Three or Four 16-Bit Sigma-Delta A/D
Converters with Differential PGA Inputs
16-Bit Timer_B With Three
Capture/Compare-With-Shadow Registers
16-Bit Timer_A With Three
Capture/Compare Registers
On-Chip Comparator
Four Universal Serial Communication
Interfaces (USCI)
− USCI_A0 and USCI_A1:
− Enhanced UART Supporting
Auto-Baudrate Detection
− IrDA Encoder and Decoder
− Synchronous SPI
− USCI_B0 and USCI_B1:
− I2C
− Synchronous SPI
Integrated LCD Driver With Contrast
Control for up to 160 Segments
D 32-Bit Hardware Multiplier
D Brownout Detector
D Supply Voltage Supervisor/Monitor With
D
D
D
D
D
Programmable Level Detection
Serial Onboard Programming,
No External Programming Voltage Needed
Programmable Code Protection by Security
Fuse
Bootstrap Loader
On Chip Emulation Module
Family Members Include:
MSP430F4783: 48KB + 256B Flash
2KB RAM
3 Sigma-Delta ADCs
MSP430F4793: 60KB + 256B Flash
2.5KB RAM
3 Sigma-Delta ADCs
MSP430F4784: 48KB + 256B Flash
2KB RAM
4 Sigma-Delta ADCs
MSP430F4794: 60KB + 256B Flash
2.5KB RAM
4 Sigma-Delta ADCs
MSP430F47x3 and MSP430F47x4 are
Available in a 100-Pin Plastic Quad
Flatpack (QFP) Package
For Complete Module Descriptions, See
The MSP430x4xx Family User’s Guide,
Literature Number SLAU056
PRODUCT PREVIEW
D Low Supply-Voltage Range, 1.8 V to 3.6 V
D Ultralow-Power Consumption:
description
The Texas Instruments MSP430 family of ultralow-power microcontrollers consists of several devices featuring
different sets of peripherals targeted for various applications. The architecture, combined with five low-power
modes, is optimized to achieve extended battery life in portable measurement applications. The device features
a powerful 16-bit RISC CPU, 16-bit registers, and constant generators that contribute to maximum code
efficiency. The digitally controlled oscillator (DCO) allows wake-up from low-power modes to active mode in less
than 6μs.
The MSP430F47xx series are microcontroller configurations targeted to single phase electricity meters with
three or four 16-bit sigma-delta A/D converters. Each channel has a differential input pair and programmable
input gain. Also integrated are two 16-bit timers, three universal serial communication interfaces (USCI), TBD
I/O pins, and a liquid crystal driver (LCD) with integrated contrast control.
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range
from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage
because very small parametric changes could cause the device not to meet its published specifications. These devices have limited
built-in ESD protection.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright © 2007, Texas Instruments Incorporated
PRODUCT PREVIEW information concerns products in the formative or
design phase of development. Characteristic data and other
specifications are design goals. Texas Instruments reserves the right to
change or discontinue these products without notice.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
AVAILABLE OPTIONS
PACKAGED DEVICES
TA
PLASTIC 100-PIN QFP
(PZ)
PRODUCT PREVIEW
−40°C to 85°C
MSP430F4783IPZ
MSP430F4793IPZ
MSP430F4784IPZ
MSP430F4794IPZ
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
pin designation, MSP430x47xxIPZ
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
MSP430F47x4IPZ
P2.4/UCA0TXD/UCA0SIMO
P2.5/UCA0RXD/UCA0SOMI
P2.6/CAOUT
P2.7
P3.0/UCB0STE/UCA0CLK
P3.1/UCB0SIMO/UCB0SDA
P3.2/UCB0SOMI/UCB0SCL
P3.3/UCB0CLK/UCA0STE
P3.4
P3.5
P3.6
P3.7
P4.0/UCA1TXD/UCA1SIMO
P4.1/UCA1RXD/UCA1SOMI
DVSS2
DVCC2
LCDCAP/R33
P5.7/R23
P5.6/LCDREF/R13
P5.5/R03
P5.4/COM3
P5.3/COM2
P5.2/COM1
COM0
P4.2/UCB1STE/UCA1CLK/S39
PRODUCT PREVIEW
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
P9.3/S14
P9.2/S15
P9.1/S16
P9.0/S17
P8.7/S18
P8.6/S19
P8.5/S20
P8.4/S21
P8.3/S22
P8.2/S23
P8.1/S24
P8.0/S25
P7.7/S26
P7.6/S27
P7.5/S28
P7.4/S29
P7.3/S30
P7.2/S31
P7.1/S32
P7.0/S33
P4.7/S34
P4.6/S35
P4.5/UCB1CLK/UCA1STE/S36
P4.4/UCB1SOMI/UCB1SCL/S37
P4.3/UCB1SIMO/UCB1SDA/S38
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
DVCC1
A0+
A0−
A1+
A1−
A2+
A2−
XIN
XOUT
VREF
NC
P5.1/S0
S1
P10.7/S2
P10.6/S3
P10.5/S4
P10.4/S5
P10.3/S6
P10.2/S7
P10.1/S8
P10.0/S9
P9.7/S10
P9.6/S11
P9.5/S12
P9.4/S13
82
81
80
79
78
77
76
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
AVCC
DVSS1
AVSS1
A3−
A3+
P5.0/SVSIN
RST/NMI
TCK
TMS
TDI/TCLK
TDO/TDI
XT2IN
XT2OUT
P1.0/TA0
P1.1/TA0/MCLK
P1.2/TA1
P1.3/TBOUTH/SVSOUT
P1.4/TBCLK/SMCLK
P1.5/TACLK/ACLK
P1.6/CA0
P1.7/CA1
P2.0/TA2
P2.1/TB0
P2.2/TB1
P2.3/TB2
PZ PACKAGE
(TOP VIEW)
A3+ and A3− are not connected in MSP430x47x3 devices.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
MSP430x47x3 functional block diagrams
XIN
XT2IN
XOUT
XT2OUT
2
2
Oscillators
FLL+
DVCC1/2
AVCC
AVSS
P1.x/P2.x
2x8
SD16_A
(w/o BUF)
3
Sigma−
Delta A/D
Converter
ACLK
SMCLK
MCLK
Flash_A
RAM
60kB
48kB
2.5kB
2.0kB
P3.x/P4.x
P5.x
3x8
P7.x/P8.x
P9.x/P10.x
4x8/2x16
Ports P1/P2
Comparator
_A
Ports
Ports
P3/P4
P7/P8
2x8 I/O
P5
P9/P10
Interrupt
capability &
3x8 I/O with 4x8/2x16 I/O
pull−up/down pull−up/down pull−up/down
Resistors
Resistors
Resistors
MAB
16MHz
CPU
incl. 16
Registers
MDB
Emulation
(2 BP)
Brownout
Protection
JTAG
Interface
SVS/SVM
PRODUCT PREVIEW
DVSS1/2
Hardware
Multiplier
(32x32)
MPY,
MPYS,
MAC,
MACS
Timer_B3
Watchdog
WDT+
15/16−Bit
LCD_A
Timer_A3
3 CC
Registers
3 CC
Registers,
Shadow
Reg
Basic Timer
160
Segments
1,2,3,4 Mux
USCI_A0
(UART/LIN,
IrDA, SPI)
USCI_A1
(UART/LIN,
IrDA, SPI)
USCI_B0
(SPI, I2C)
USCI_B1
(SPI, I2C)
P3.x/P4.x
P5.x
3x8
P7.x/P8.x
P9.x/P10.x
4x8/2x16
RST/NMI
MSP430x47x4 functional block diagrams
XIN
XT2IN
XOUT
XT2OUT
2
2
Oscillators
FLL+
DVCC1/2
AVSS
P1.x/P2.x
SD16_A
(w/o BUF)
4
Sigma−
Delta A/D
Converter
ACLK
SMCLK
Flash_A
RAM
60kB
48kB
2.5kB
2.0kB
Ports P1/P2
Comparator
_A
Ports
P7/P8
P9/P10
USCI_A0
(UART/LIN,
IrDA, SPI)
USCI_A1
(UART/LIN,
IrDA, SPI)
USCI_B0
(SPI, I2C)
USCI_B1
(SPI, I2C)
2x8 I/O
Interrupt
capability &
3x8 I/O with 4x8/2x16 I/O
pull−up/down pull−up/down pull−up/down
Resistors
Resistors
Resistors
MDB
Brownout
Protection
SVS/SVM
Hardware
Multiplier
(32x32)
MPY,
MPYS,
MAC,
MACS
Timer_B3
Watchdog
WDT+
15/16−Bit
LCD_A
Timer_A3
3 CC
Registers
3 CC
Registers,
Shadow
Reg
Basic Timer
RST/NMI
4
Ports
P3/P4
P5
MAB
Emulation
(2 BP)
JTAG
Interface
AVCC
2x8
MCLK
16MHz
CPU
incl. 16
Registers
DVSS1/2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
160
Segments
1,2,3,4 Mux
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
MSP430x47xx Terminal Functions
NAME
NO.
I/O
DESCRIPTION
DVCC1
1
A0+
2
I
Digital supply voltage, positive terminal.
SD16_A positive analog input A0 (see Note 1)
A0−
3
I
SD16_A negative analog input A0 (see Note 1)
A1+
4
I
SD16_A positive analog input A1 (see Note 1)
A1−
5
I
SD16_A negative analog input A1 (see Note 1)
A2+
6
I
SD16_A positive analog input A2 (see Note 1)
A2−
7
I
SD16_A negative analog input A2 (see Note 1)
XIN
8
I
Input port for crystal oscillator XT1. Standard or watch crystals can be connected.
XOUT
9
O
Output terminal of crystal oscillator XT1
VREF
10
I/O
Input for an external reference voltage /
internal reference voltage output (can be used as mid-voltage)
NC
11
P5.1/S0
12
I/O
Internally not connected. Can be connected to VSS.
General-purpose digital I/O / LCD segment output 0
S1
13
O
LCD segment output 1
P10.7/S2
14
I/O
General-purpose digital I/O / LCD segment output 2
P10.6/S3
15
I/O
General-purpose digital I/O / LCD segment output 3
P10.5/S4
16
I/O
General-purpose digital I/O / LCD segment output 4
P10.4/S5
17
I/O
General-purpose digital I/O / LCD segment output 5
P10.3/S6
18
I/O
General-purpose digital I/O / LCD segment output 6
P10.2/S7
19
I/O
General-purpose digital I/O / LCD segment output 7
P10.1/S8
20
I/O
General-purpose digital I/O / LCD segment output 8
P10.0/S9
21
I/O
General-purpose digital I/O / LCD segment output 9
P9.7/S10
22
I/O
General-purpose digital I/O / LCD segment output 10
P9.6/S11
23
I/O
General-purpose digital I/O / LCD segment output 11
P9.5/S12
24
I/O
General-purpose digital I/O / LCD segment output 12
P9.4/S13
25
I/O
General-purpose digital I/O / LCD segment output 13
P9.3/S14
26
I/O
General-purpose digital I/O / LCD segment output 14
P9.2/S15
27
I/O
General-purpose digital I/O / LCD segment output 15
P9.1/S16
28
I/O
General-purpose digital I/O / LCD segment output 16
P9.0/S17
29
I/O
General-purpose digital I/O / LCD segment output 17
P8.7/S18
30
I/O
General-purpose digital I/O / LCD segment output 18
P8.6/S19
31
I/O
General-purpose digital I/O / LCD segment output 19
P8.5/S20
32
I/O
General-purpose digital I/O / LCD segment output 20
P8.4/S21
33
I/O
General-purpose digital I/O / LCD segment output 21
P8.3/S22
34
I/O
General-purpose digital I/O / LCD segment output 22
P8.2/S23
35
I/O
General-purpose digital I/O / LCD segment output 23
P8.1/S24
36
I/O
General-purpose digital I/O / LCD segment output 24
P8.0/S25
37
I/O
General-purpose digital I/O / LCD segment output 25
P7.7/S26
38
I/O
General-purpose digital I/O / LCD segment output 26
P7.6/S27
39
I/O
General-purpose digital I/O / LCD segment output 27
P7.5/S28
40
I/O
General-purpose digital I/O / LCD segment output 28
P7.4/S29
41
I/O
General-purpose digital I/O / LCD segment output 29
P7.3/S30
42
I/O
General-purpose digital I/O / LCD segment output 30
PRODUCT PREVIEW
TERMINAL
NOTES: 1. Open connection recommended for all unused analog inputs.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
MSP430x47xx Terminal Functions (Continued)
TERMINAL
PRODUCT PREVIEW
NAME
NO.
I/O
DESCRIPTION
P7.2/S31
43
I/O
General-purpose digital I/O / LCD segment output 31
P7.1/S32
44
I/O
General-purpose digital I/O / LCD segment output 32
P7.0/S33
45
I/O
General-purpose digital I/O / LCD segment output 33
P4.7/S34
46
I/O
General-purpose digital I/O / LCD segment output 34
P4.6/S35
47
I/O
General-purpose digital I/O / LCD segment output 35
P4.5/
UCB1CLK/UCA1STE/
S36
48
I/O
General-purpose digital I/O /
USCI_B1 clock input/output / USCI_A1 slave transmit enable /
LCD segment output 36
P4.4/
UCB1SOMI/UCB1SCL/
S37
49
I/O
General-purpose digital I/O /
USCI_B1 slave out/master in in SPI mode, SCL I2C clock in I2C mode /
LCD segment output 37
P4.3/
UCB1SIMO/UCB1SDA/
S38
50
I/O
General-purpose digital I/O /
USCI_B1 slave in/master out in SPI mode, SDA I2C data in I2C mode /
LCD segment output 38
P4.2/
UCB1STE/UCA1CLK/
S39
51
I/O
General-purpose digital I/O /
USCI_B1 slave transmit enable / USCI_A1 clock input/output /
LCD segment output 39
COM0
52
O
COM0−3 are used for LCD backplanes.
P5.2/COM1
53
I/O
General-purpose digital I/O / common output, COM0−3 are used for LCD backplanes.
P5.3/COM2
54
I/O
General-purpose digital I/O / common output, COM0−3 are used for LCD backplanes.
P5.4/COM3
55
I/O
General-purpose digital I/O / common output, COM0−3 are used for LCD backplanes.
P5.5/R03
56
I/O
General-purpose digital I/O / Input port of lowest analog LCD level (V5)
P5.6/LCDREF/R13
57
I/O
General-purpose digital I/O / External reference voltage input for regulated LCD voltage / Input port
of third most positive analog LCD level (V4 or V3)
P5.7/R23
58
I/O
General-purpose digital I/O / Input port of second most positive analog LCD level (V2)
LCDCAP/R33
59
I
DVCC2
60
Digital supply voltage, positive terminal.
DVSS2
61
Digital supply voltage, negative terminal.
P4.1/
UCA1RXD/UCA1SOMI
62
I/O
General-purpose digital I/O /
USCI_A1 receive data input in UART mode, slave out/master in in SPI mode
P4.0/
UCA1TXD/UCA1SIMO
63
I/O
General-purpose digital I/O /
USCI_A1 transmit data output in UART mode, slave in/master out in SPI mode
P3.7
64
I/O
General-purpose digital I/O
P3.6
65
I/O
General-purpose digital I/O
P3.5
66
I/O
General-purpose digital I/O
P3.4
67
I/O
General-purpose digital I/O
P3.3/
UCB0CLK/UCA0STE
68
I/O
General-purpose digital I/O /
USCI_B0 clock input/output / USCI_A0 slave transmit enable
P3.2/
UCB0SOMI/UCB0SCL
69
I/O
General-purpose digital I/O /
USCI_B1 slave out/master in in SPI mode, SCL I2C clock in I2C mode
P3.1/
UCB0SIMO/UCB0SDA
70
I/O
General-purpose digital I/O /
USCI_B1 slave in/master out in SPI mode, SDA I2C data in I2C mode
P3.0/
UCB0STE/UCA0CLK
71
I/O
General-purpose digital I/O /
USCI_B0 slave transmit enable / USCI_A0 clock input/output
P2.7
72
I/O
General-purpose digital I/O
P2.6/CAOUT
73
I/O
General-purpose digital I/O / Comparator_A output
6
LCD Capacitor connection / Input/output port of most positive analog LCD level (V1)
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
TERMINAL
NAME
NO.
I/O
DESCRIPTION
P2.5/
UCA0RXD/UCA0SOMI
74
I/O
General-purpose digital I/O / USCI_A0 receive data input in UART mode, slave out/master in in SPI
mode
P2.4/
UCA0TXD/UCA0SIMO
75
I/O
General-purpose digital I/O / USCI_A0 transmit data output in UART mode, slave in/master out in
SPI mode
P2.3/TB2
76
I/O
General-purpose digital I/O / Timer_B3 CCR2. Capture: CCI2A/CCI2B input, compare: Out2 output
P2.2/TB1
77
I/O
General-purpose digital I/O / Timer_B3 CCR1. Capture: CCI1A/CCI1B input, compare: Out1 output
P2.1/TB0
78
I/O
General-purpose digital I/O / Timer_B3 CCR0. Capture: CCI0A/CCI0B input, compare: Out0 output
P2.0/TA2
79
I/O
General-purpose digital I/O / Timer_A Capture: CCI2A input, compare: Out2 output
P1.7/CA1
80
I/O
General-purpose digital I/O / Comparator_A input
P1.6/CA0
81
I/O
General-purpose digital I/O / Comparator_A input
P1.5/TACLK/
ACLK
82
I/O
General-purpose digital I/O / Timer_A, clock signal TACLK input /
ACLK output (divided by 1, 2, 4, or 8)
P1.4/TBCLK/
SMCLK
83
I/O
General-purpose digital I/O / input clock TBCLK—Timer_B3 /
submain system clock SMCLK output
P1.3/TBOUTH/
SVSOUT
84
I/O
General-purpose digital I/O / switch all PWM digital output ports to high impedance—Timer_B3 TB0
to TB2 / SVS: output of SVS comparator
P1.2/TA1
85
I/O
General-purpose digital I/O / Timer_A, Capture: CCI1A input, compare: Out1 output
P1.1/TA0/MCLK
86
I/O
General-purpose digital I/O / Timer_A. Capture: CCI0B input / MCLK output.
Note: TA0 is only an input on this pin / BSL receive
P1.0/TA0
87
I/O
General-purpose digital I/O / Timer_A. Capture: CCI0A input, compare: Out0 output / BSL transmit
XT2OUT
88
O
Output terminal of crystal oscillator XT2
XT2IN
89
I
Input port for crystal oscillator XT2. Only standard crystals can be connected.
TDO/TDI
90
I/O
TDI/TCLK
91
I
Test data input or test clock input. The device protection fuse is connected to TDI/TCLK.
TMS
92
I
Test mode select. TMS is used as an input port for device programming and test.
TCK
93
I
Test clock. TCK is the clock input port for device programming and test.
RST/NMI
94
I
Reset input or nonmaskable interrupt input port
P5.0/SVSIN
95
I/O
A3+
(MSP430x47x4 only)
96
I
SD16_A positive analog input A3 (see Note 1) − Not connected in MSP430x47x3 devices
A3−
(MSP430x47x4 only)
97
I
SD16_A negative analog input A3 (see Note 1) − Not connected in MSP430x47x3 devices
AVSS
98
Analog supply voltage, negative terminal.
DVSS1
99
Digital supply voltage, negative terminal.
AVCC
100
Analog supply voltage, positive terminal. Must not power up prior to DVCC1/DVCC2.
PRODUCT PREVIEW
MSP430x47xx Terminal Functions (Continued)
Test data output port. TDO/TDI data output or programming data input terminal
General-purpose digital I/O / analog input to supply voltage supervisor
NOTES: 1. Open connection recommended for all unused analog inputs.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
short-form description
CPU
The MSP430 CPU has a 16-bit RISC architecture
that is highly transparent to the application. All
operations, other than program-flow instructions,
are performed as register operations in
conjunction with seven addressing modes for
source operand and four addressing modes for
destination operand.
PC/R0
Stack Pointer
SP/R1
SR/CG1/R2
Status Register
Constant Generator
The CPU is integrated with 16 registers that
provide reduced instruction execution time. The
register-to-register operation execution time is
one cycle of the CPU clock.
PRODUCT PREVIEW
Program Counter
Four of the registers, R0 to R3, are dedicated as
program counter, stack pointer, status register,
and constant generator respectively. The
remaining registers are general-purpose
registers.
Peripherals are connected to the CPU using data,
address, and control buses, and can be handled
with all instructions.
instruction set
The instruction set consists of 51 instructions with
three formats and seven address modes. Each
instruction can operate on word and byte data.
Table 1 shows examples of the three types of
instruction formats; the address modes are listed
in Table 2.
CG2/R3
General-Purpose Register
R4
General-Purpose Register
R5
General-Purpose Register
R6
General-Purpose Register
R7
General-Purpose Register
R8
General-Purpose Register
R9
General-Purpose Register
R10
General-Purpose Register
R11
General-Purpose Register
R12
General-Purpose Register
R13
General-Purpose Register
R14
General-Purpose Register
R15
Table 1. Instruction Word Formats
Dual operands, source-destination
e.g. ADD R4,R5
R4 + R5 −−−> R5
Single operands, destination only
e.g. CALL
PC −−>(TOS), R8−−> PC
Relative jump, un/conditional
e.g. JNE
R8
Jump-on-equal bit = 0
Table 2. Address Mode Descriptions
ADDRESS MODE
Indirect
D
D
D
D
D
Indirect
autoincrement
Register
Indexed
Symbolic (PC relative)
Absolute
Immediate
NOTE: S = source
8
S D
D
D
D
D
SYNTAX
EXAMPLE
MOV Rs,Rd
MOV R10,R11
MOV X(Rn),Y(Rm)
MOV 2(R5),6(R6)
MOV EDE,TONI
OPERATION
R10
−−> R11
M(2+R5)−−> M(6+R6)
M(EDE) −−> M(TONI)
MOV &MEM,&TCDAT
M(MEM) −−> M(TCDAT)
MOV @Rn,Y(Rm)
MOV @R10,Tab(R6)
M(R10) −−> M(Tab+R6)
D
MOV @Rn+,Rm
MOV @R10+,R11
M(R10) −−> R11
R10 + 2−−> R10
D
MOV #X,TONI
MOV #45,TONI
D = destination
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
#45
−−> M(TONI)
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
operating modes
The MSP430 has one active mode and five software selectable low-power modes of operation. An interrupt
event can wake up the device from any of the five low-power modes, service the request and restore back to
the low-power mode on return from the interrupt program.
The following six operating modes can be configured by software:
D Active mode AM
−
All clocks are active
D Low-power mode 0 (LPM0)
−
CPU is disabled
ACLK and SMCLK remain active. MCLK is disabled
FLL+ loop control remains active
D Low-power mode 1 (LPM1)
CPU is disabled
FLL+ loop control is disabled
ACLK and SMCLK remain active. MCLK is disabled
PRODUCT PREVIEW
−
D Low-power mode 2 (LPM2)
−
CPU is disabled
MCLK, FLL+ loop control, and DCOCLK are disabled
DCO’s dc-generator remains enabled
ACLK remains active
D Low-power mode 3 (LPM3)
−
CPU is disabled
MCLK, FLL+ loop control, and DCOCLK are disabled
DCO’s dc-generator is disabled
ACLK remains active
D Low-power mode 4 (LPM4)
−
CPU is disabled
ACLK is disabled
MCLK, FLL+ loop control, and DCOCLK are disabled
DCO’s dc-generator is disabled
Crystal oscillator is stopped
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
interrupt vector addresses
The interrupt vectors and the power-up starting address are located in the address range 0FFFFh−0FFE0h. The
vector contains the 16-bit address of the appropriate interrupt-handler instruction sequence.
If the reset vector (located at address 0FFFEh) contains 0FFFFh (e.g. flash is not programmed) the CPU will
go into LPM4 immediately after power up.
INTERRUPT FLAG
SYSTEM INTERRUPT
WORD
ADDRESS
PRIORITY
Power-Up
External Reset
Watchdog
Flash Memory
PC Out-of-Range (see Note 4)
PORIFG
RSTIFG
WDTIFG
KEYV
(see Note 1)
Reset
0FFFEh
15, highest
NMI
Oscillator Fault
Flash Memory Access Violation
NMIIFG (see Notes 1 and 3)
OFIFG (see Notes 1 and 3)
ACCVIFG (see Notes 1 and 3)
(Non)maskable
(Non)maskable
(Non)maskable
0FFFCh
14
Timer_B3
TBCCR0 CCIFG (see Note 2)
Maskable
0FFFAh
13
Timer_B3
TBCCR1 to TBCCR2 CCIFGs
TBIFG (see Notes 1 and 2)
Maskable
0FFF8h
12
PRODUCT PREVIEW
INTERRUPT SOURCE
Comparator_A
CAIFG
Maskable
0FFF6h
11
Watchdog Timer
WDTIFG
Maskable
0FFF4h
10
USCI_A0/B0 Receive
UCA0RXIFG (see Note 1),
UCB0RXIFG (SPI mode) or
UCB0STAT UCALIFG, UCNACKIFG, UCSTTIFG,
UCSTPIFG (I2C mode)
(see Note 1)
Maskable
0FFF2h
9
USCI_A0/B0 Transmit
UCA0TXIFG (see Note 1),
UCB0TXIFG (SPI mode) or UCB0RXIFG and
UCB0TXIFG (I2C mode)
(see Note 1)
Maskable
0FFF0h
8
SD16_A
SD16CCTLx SD16OVIFG,
SD16CCTLx SD16IFG
(see Notes 1 and 2)
Maskable
0FFEEh
7
Timer_A3
TACCR0 CCIFG (see Note 2)
Maskable
0FFECh
6
Timer_A3
TACCR1 and TACCR2 CCIFGs,
TAIFG (see Notes 1 and 2)
Maskable
0FFEAh
5
I/O Port P1
(Eight Flags)
P1IFG.0 to P1IFG.7
(see Notes 1 and 2)
Maskable
0FFE8h
4
USCI_A1/B1 Receive
UCA1RXIFG (see Notes 1 and 2),
UCB1RXIFG (SPI mode) or
UCB1STAT UCALIFG, UCNACKIFG, UCSTTIFG,
UCSTPIFG (I2C mode)
(see Notes 1 and 2)
Maskable
0FFE6h
3
USCI_A1/B1 Transmit
UCA1TXIFG (see Notes 1 and 2),
UCB1TXIFG (SPI mode) or UCB1RXIFG and
UCB1TXIFG (I2C mode)
(see Notes 1 and 2)
Maskable
0FFE4h
2
I/O Port P2
(Eight Flags)
P2IFG.0 to P2IFG.7
(see Notes 1 and 2)
Maskable
0FFE2h
1
Basic Timer1
BTIFG
Maskable
0FFE0h
0, lowest
NOTES: 1. Multiple source flags
2. Interrupt flags are located in the module.
3. (Non)maskable: the individual interrupt-enable bit can disable an interrupt event, but the general-interrupt enable can not disable
it.
4. A reset is generated if the CPU tries to fetch instructions from within the module register memory address range (0h−01FFh).
10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
special function registers
Most interrupt and module-enable bits are collected in the lowest address space. Special-function register bits
not allocated to a functional purpose are not physically present in the device. This arrangement provides simple
software access.
interrupt enable 1 and 2
Address
7
6
00h
5
4
ACCVIE
rw−0
3
2
1
0
NMIIE
OFIE
WDTIE
rw−0
rw−0
rw−0
Watchdog Timer interrupt enable. Inactive if watchdog mode is selected. Active if Watchdog
Timer is configured in interval timer mode.
OFIE
Oscillator fault enable
NMIIE
(Non)maskable interrupt enable
ACCVIE
Flash access violation interrupt enable
Address
01h
7
6
5
4
3
2
1
0
BTIE
UCB0TXIE
UCB0RXIE
UCA0TXIE
UCA0RXIE
rw−0
rw−0
rw−0
rw−0
rw−0
UCA0RXIE
USCI_A0 receive-interrupt enable
UCA0TXIE
USCI_A0 transmit-interrupt enable
UCB0RXIE
USCI_B0 receive-interrupt enable
UCB0TXIE
USCI_B0 transmit-interrupt enable
BTIE
Basic timer interrupt enable
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
PRODUCT PREVIEW
WDTIE
11
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
interrupt flag register 1 and 2
Address
7
6
5
02h
3
2
1
0
NMIIFG
RSTIFG
PORIFG
OFIFG
WDTIFG
rw−0
rw−(0)
rw−(1)
rw−1
rw−(0)
WDTIFG
Set on Watchdog Timer overflow (in watchdog mode) or security key violation.
Reset on VCC power-up or a reset condition at RST/NMI pin in reset mode.
OFIFG
Flag set on oscillator fault
RSTIFG
External reset interrupt flag. Set on a reset condition at RST/NMI pin in reset mode. Reset
on VCC power-up
PORIFG
Power-On interrupt flag. Set on VCC power-up.
NMIIFG
Set via RST/NMI pin
Address
7
03h
PRODUCT PREVIEW
4
6
5
3
2
1
0
BTIFG
UCB0
TXIFG
UCB0
RXIFG
UCA0
TXIFG
UCA0
RXIFG
rw−0
rw−1
rw−0
rw−1
rw−0
UCA0RXIFG
USCI_A0 receive-interrupt flag
UCA0TXIFG
USCI_A0 transmit-interrupt flag
UCB0RXIFG
USCI_B0 receive-interrupt flag
UCB0TXIFG
USCI_B0 transmit-interrupt flag
BTIFG
Basic Timer1 interrupt flag
Legend
rw:
rw-0,1:
rw-(0,1):
4
Bit can be read and written.
Bit can be read and written. It is Reset or Set by PUC.
Bit can be read and written. It is Reset or Set by POR.
SFR bit is not present in device
12
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
memory organization
MSP430F4783/MSP430F4784
MSP430F4793/MSP430F4794
Memory
Main: interrupt vector
Main: code memory
Size
Flash
Flash
48KB
0FFFFh − 0FFE0h
0FFFFh − 04000h
60KB
0FFFFh − 0FFE0h
0FFFFh − 01100h
Information memory
Size
Flash
256 Byte
010FFh − 01000h
256 Byte
010FFh − 01000h
Boot memory
Size
ROM
1KB
0FFFh − 0C00h
1KB
0FFFh − 0C00h
Size
2KB
09FFh − 0200h
2.5KB
0BFFh − 0200h
16-bit
8-bit
8-bit SFR
01FFh − 0100h
0FFh − 010h
0Fh − 00h
01FFh − 0100h
0FFh − 010h
0Fh − 00h
RAM
Peripherals
The MSP430 bootstrap loader (BSL) enables users to program the flash memory or RAM using a UART serial
interface. Access to the MSP430 memory via the BSL is protected by user-defined password. For complete
description of the features of the BSL and its implementation, see the Application report Features of the MSP430
Bootstrap Loader, Literature Number SLAA089.
BSL Function
PZ Package Pins
Data Transmit
87 - P1.0
Data Receive
86 - P1.1
flash memory, Flash_A
The flash memory can be programmed via the JTAG port, the bootstrap loader, or in-system by the CPU. The
CPU can perform single-byte and single-word writes to the flash memory. Features of the flash memory include:
D Flash memory has n segments of main memory and four segments of information memory (A to D) of 64
bytes each. Each segment in main memory is 512 bytes in size.
D Segments 0 to n may be erased in one step, or each segment may be individually erased.
D Segments A to D can be erased individually, or as a group with segments 0−n.
Segments A to D are also called information memory.
D Segment A contains calibration data. After reset segment A is protected against programming or erasing.
It can be unlocked but care should be taken not to erase this segment if the calibration data is required.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
PRODUCT PREVIEW
bootstrap loader (BSL)
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
peripherals
Peripherals are connected to the CPU through data, address, and control busses and can be handled using
all instructions. For complete module descriptions, refer to the MSP430x4xx Family User’s Guide, literature
number SLAU056.
digital I/O
There are nine 8-bit I/O ports implemented—ports P1 through P5 and P7 through P10.
D
D
D
D
D
D
All individual I/O bits are independently programmable.
Any combination of input, output, and interrupt conditions is possible.
Edge-selectable interrupt input capability for all the eight bits of ports P1 and P2.
Read/write access to port-control registers is supported by all instructions.
Ports P7/P8 and P9/P10 can be accessed word-wise as ports PA and PB respectively.
Each I/O has an individually programmable pull−up/pull−down resistor.
PRODUCT PREVIEW
oscillator and system clock
The clock system in the MSP430x47xx is supported by the FLL+ module that includes support for a 32768-Hz
watch crystal oscillator, an internal digitally-controlled oscillator (DCO) and a 8 MHz high frequency crystal
oscillator (XT1) plus a 16 MHz high frequency crystal oscillator (XT2). The FLL+ clock module is designed to
meet the requirements of both low system cost and low-power consumption. The FLL+ features a digital
frequency locked loop (FLL) hardware which in conjunction with a digital modulator stabilizes the DCO
frequency to a programmable multiple of the watch crystal frequency. The internal DCO provides a fast turn-on
clock source and stabilizes in less than 6 μs. The FLL+ module provides the following clock signals:
D
D
D
D
Auxiliary clock (ACLK), sourced from a 32768-Hz watch crystal or a high frequency crystal.
Main clock (MCLK), the system clock used by the CPU.
Sub-Main clock (SMCLK), the sub-system clock used by the peripheral modules.
ACLK/n, the buffered output of ACLK, ACLK/2, ACLK/4, or ACLK/8.
brownout, supply voltage supervisor
The brownout circuit is implemented to provide the proper internal reset signal to the device during power on
and power off. The supply voltage supervisor (SVS) circuitry detects if the supply voltage drops below a user
selectable level and supports both supply voltage supervision (the device is automatically reset) and supply
voltage monitoring (SVM, the device is not automatically reset).
The CPU begins code execution after the brownout circuit releases the device reset. However, VCC may not
have ramped to VCC(min) at that time. The user must insure the default FLL+ settings are not changed until VCC
reaches VCC(min). If desired, the SVS circuit can be used to determine when VCC reaches VCC(min).
hardware multiplier
The multiplication operation is supported by a dedicated peripheral module. The module performs operations
with 32-bit, 24-bit, 16-bit and 8-bit operands. The module is capable of supporting signed and unsigned
multiplication as well as signed and unsigned multiply and accumulate operations.
WDT+ watchdog timer
The primary function of the watchdog timer (WDT+) module is to perform a controlled system restart after a
software problem occurs. If the selected time interval expires, a system reset is generated. If the watchdog
function is not needed in an application, the module can be configured as an interval timer and can generate
interrupts at selected time intervals.
14
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
Universal Serial Communication Interfaces (USCI_A0, USCI_B0, USCI_A1, USCI_B1)
The universal serial communication interface (USCI) module is used for serial data communication. The USCI
module supports synchronous communication protocols like SPI (3 or 4 pin), I2C and asynchronous
communication protocols like UART, enhanced UART with automatic baudrate detection (LIN), and IrDA.
USCI_A0 and USCI_A1 provides support for SPI (3 or 4 pin), UART, enhanced UART and IrDA.
USCI_B0 and USCI_B1 provides support for SPI (3 or 4 pin) and I2C.
timer_A3
Timer_A3 is a 16-bit timer/counter with three capture/compare registers. Timer_A3 can support multiple
capture/compares, PWM outputs, and interval timing. Timer_A3 also has extensive interrupt capabilities.
Interrupts may be generated from the counter on overflow conditions and from each of the capture/compare
registers.
Timer_A3 Signal Connections
Module Input
Name
82 - P1.5
TACLK
TACLK
ACLK
ACLK
SMCLK
SMCLK
82 - P1.5
TACLK
INCLK
87 - P1.0
TA0
CCI0A
86 - P1.1
TA0
CCI0B
DVSS
GND
85 - P1.2
79 - P2.0
DVCC
VCC
TA1
CCI1A
CAOUT (internal)
CCI1B
DVSS
GND
DVCC
VCC
TA2
CCI2A
ACLK (internal)
CCI2B
DVSS
GND
DVCC
VCC
POST OFFICE BOX 655303
Module Block
Module Output
Signal
Timer
NA
Output Pin Number
PRODUCT PREVIEW
Input Pin Number
Device Input
Signal
87 - P1.0
CCR0
TA0
85 - P1.2
CCR1
TA1
79 - P2.0
CCR2
• DALLAS, TEXAS 75265
TA2
15
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
timer_B3
Timer_B3 is a 16-bit timer/counter with three capture/compare registers. Timer_B3 can support multiple
capture/compares, PWM outputs, and interval timing. Timer_B3 also has extensive interrupt capabilities.
Interrupts may be generated from the counter on overflow conditions and from each of the capture/compare
registers.
Timer_B3 Signal Connections
Input Pin Number
Device Input
Signal
Module Input
Name
83 - P1.4
TBCLK
TBCLK
ACLK
ACLK
SMCLK
SMCLK
83 - P1.4
TBCLK
INCLK
78 - P2.1
TB0
CCI0A
TB0
CCI0B
DVSS
GND
PRODUCT PREVIEW
78 - P2.1
DVCC
VCC
77 - P2.2
TB1
CCI1A
77 - P2.2
TB1
CCI1B
DVSS
GND
76 - P2.3
76 - P2.3
DVCC
VCC
TB2
CCI2A
TB2
CCI2B
DVSS
GND
DVCC
VCC
Module Block
Module Output
Signal
Timer
NA
Output Pin Number
78 - P2.1
CCR0
TB0
77 - P2.2
CCR1
TB1
76 - P2.3
CCR2
TB2
comparator_A
The primary function of the comparator_A module is to support precision slope analog-to-digital conversions,
battery-voltage supervision, and monitoring of external analog signals.
SD16_A
The SD16_A module integrates in MSP430x47x3 three and in MSP430x47x4 four independent 16-bit
Sigma-Delta A/D converters. Each channel is designed with a fully differential analog input pair and
programmable gain amplifier input stage. In addition to external analog inputs, an internal VCC sense and
temperature sensor are also available.
Basic Timer1
The Basic Timer1 has two independent 8-bit timers which can be cascaded to form a 16-bit timer/counter. Both
timers can be read and written by software. The Basic Timer1 can be used to generate periodic interrupts and
clock for the LCD module.
LCD driver with regulated charge pump
The LCD_A driver generates the segment and common signals required to drive an LCD display. The LCD_A
controller has dedicated data memory to hold segment drive information. Common and segment signals are
generated as defined by the mode. Static, 2-MUX, 3-MUX, and 4-MUX LCDs are supported by this peripheral.
The module can provide a LCD voltage independent of the supply voltage via an integrated charge pump.
Furthermore it is possible to control the level of the LCD voltage and thus contrast in software.
16
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
peripheral file map
Watchdog
Watchdog timer control
WDTCTL
0120h
Flash_A
Flash control 4
Flash control 3
Flash control 2
Flash control 1
FCTL4
FCTL3
FCTL2
FCTL1
01BEh
012Ch
012Ah
0128h
Timer_B3
_
Capture/compare register 2
TBCCR2
0196h
Capture/compare register 1
TBCCR1
0194h
Capture/compare register 0
TBCCR0
0192h
Timer_B register
TBR
0190h
Capture/compare control 2
TBCCTL2
0186h
Capture/compare control 1
TBCCTL1
0184h
Capture/compare control 0
TBCCTL0
0182h
Timer_B control
TBCTL
0180h
Timer_B interrupt vector
TBIV
011Eh
Capture/compare register 2
TACCR2
0176h
Capture/compare register 1
TACCR1
0174h
Capture/compare register 0
TACCR0
0172h
Timer_A register
TAR
0170h
Capture/compare control 2
TACCTL2
0166h
Capture/compare control 1
TACCTL1
0164h
Capture/compare control 0
TACCTL0
0162h
Timer_A control
TACTL
0160h
Timer_A interrupt vector
TAIV
012Eh
MPY32 control 0
MPY32CTL0
015Ch
64-bit result 3 − most significant word
RES3
015Ah
64-bit result 2
RES2
0158h
64-bit result 1
RES1
0156h
64-bit result 0 − least significant word
RES0
0154h
Second 32-bit operand, high word
OP2H
0152h
Second 32-bit operand, low word
OP2L
0150h
Multiply signed + accumulate/
32-bit operand1, high word
MACS32H
014Eh
Multiply signed + accumulate/
32-bit operand1, low word
MACS32L
014Ch
Multiply + accumulate/
32-bit operand1, high word
MAC32H
014Ah
Multiply + accumulate/
32-bit operand1, low word
MAC32L
0148h
Multiply signed/32-bit operand1, high word
MPYS32H
0146h
Multiply signed/32-bit operand1, low word
MPYS32L
0144h
Multiply unsigned/32-bit operand1, high word
MPY32H
0142h
Multiply unsigned/32-bit operand1, low word
MPY32L
0140h
Timer_A3
_
32-bit Hardware
M lti li
Multiplier
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
PRODUCT PREVIEW
PERIPHERALS WITH WORD ACCESS
17
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
peripheral file map (continued)
PERIPHERALS WITH WORD ACCESS (CONTINUED)
PRODUCT PREVIEW
32-bit Hardware
Multiplier
Sum extend
SUMEXT
013Eh
Result high word
RESHI
013Ch
Result low word
RESLO
013Ah
Second operand
OP2
0138h
Multiply signed + accumulate/operand1
MACS
0136h
Multiply + accumulate/operand1
MAC
0134h
Multiply signed/operand1
MPYS
0132h
Multiply unsigned/operand1
MPY
0130h
USCI_B0
USCI_B0 I2C own address
(see also: Peripherals with Byte Ac- USCI_B0 I2C slave address
cess)
UCB0I2COA
016Ch
UCB0I2CSA
016Eh
USCI_B1
USCI_B1 I2C own address
(see also: Peripherals with Byte Ac- USCI_B1 I2C slave address
cess)
UCB1I2COA
017Ch
UCB1I2CSA
017Eh
SD16_A
_
General Control
(see
also:
Peripher(
l
P i h
Channel 0 Control
als with Byte Access))
Channel 1 Control
SD16CTL
0100h
SD16CCTL0
0102h
SD16CCTL1
0104h
Channel 2 Control
SD16CCTL2
0106h
Channel 3 Control
SD16CCTL3
0108h
Interrupt vector word register
SD16IV
0110h
Channel 0 conversion memory
SD16MEM0
0112h
Channel 1 conversion memory
SD16MEM1
0114h
Channel 2 conversion memory
SD16MEM2
0116h
Channel 3 conversion memory
SD16MEM3
0118h
Port PA resistor enable
PAREN
014h
Port PA selection
PASEL
03Eh
Port PA direction
PADIR
03Ch
Port PA output
PAOUT
03Ah
Port PA input
PAIN
038h
Port PB resistor enable
PBREN
016h
Port PB selection
PBSEL
00Eh
Port PB direction
PBDIR
00Ch
Port PB output
PBOUT
00Ah
Port PB input
PBIN
008h
Port PA
Port PB
18
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
peripheral file map (continued)
Channel 0 Input Control
Channel 1 Input Control
Channel 2 Input Control
Channel 3 Input Control
Channel 0 preload
Channel 1 preload
Channel 2 preload
Channel 3 preload
Reserved (Internal SD16 Configuration 1)
SD16INCTL0
SD16INCTL1
SD16INCTL2
SD16INCTL3
SD16PRE0
SD16PRE1
SD16PRE2
SD16PRE3
SD16CONF1
0B0h
0B1h
0B2h
0B3h
0B8h
0B9h
0BAh
0BBh
0BFh
LCD_A
LCD Voltage Control 1
LCD Voltage Control 0
LCD Voltage Port Control 1
LCD Voltage Port Control 0
LCD memory 20
:
LCD memory 16
LCD memory 15
:
LCD memory 1
LCD control and mode
LCDAVCTL1
LCDAVCTL0
LCDAPCTL1
LCDAPCTL0
LCDM20
:
LCDM16
LCDM15
:
LCDM1
LCDACTL
0AFh
0AEh
0ADh
0ACh
0A4h
:
0A0h
09Fh
:
091h
090h
USCI_A0
USCI_A0 transmit buffer
USCI_A0 receive buffer
USCI_A0 status
USCI_A0 modulation control
USCI_A0 baud rate control 1
USCI_A0 baud rate control 0
USCI_A0 control 1
USCI_A0 control 0
USCI_A0 IrDA receive control
USCI_A0 IrDA transmit control
USCI_A0 auto baud rate control
UCA0TXBUF
UCA0RXBUF
UCA0STAT
UCA0MCTL
UCA0BR1
UCA0BR0
UCA0CTL1
UCA0CTL0
UCA0IRRCTL
UCA0IRTCTL
UCA0ABCTL
067h
066h
065h
064h
063h
062h
061h
060h
05Fh
05Eh
05Dh
USCI_B0
USCI_B0 transmit buffer
USCI_B0 receive buffer
USCI_B0 status
USCI_B1 I2C interrupt enable
USCI_B0 bit rate control 1
USCI_B0 bit rate control 0
USCI_B0 control 1
USCI_B0 control 0
UCB0TXBUF
UCB0RXBUF
UCB0STAT
UCB0I2CIE
UCB0BR1
UCB0BR0
UCB0CTL1
UCB0CTL0
06Fh
06Eh
06Dh
06Ch
06Bh
06Ah
069h
068h
USCI_A1
USCI_A1 transmit buffer
USCI_A1 receive buffer
USCI_A1 status
USCI_A1 modulation control
USCI_A1 baud rate control 1
USCI_A1 baud rate control 0
USCI_A1 control 1
USCI_A1 control 0
USCI_A1 IrDA receive control
USCI_A1 IrDA transmit control
USCI_A1 auto baud rate control
USCI_A1 interrupt flag
USCI_A1 interrupt enable
UCA1TXBUF
UCA1RXBUF
UCA1STAT
UCA1MCTL
UCA1BR1
UCA1BR0
UCA1CTL1
UCA1CTL0
UCA1IRRCTL
UCA1IRTCTL
UCA1ABCTL
UC1IFG
UC1IE
0D7h
0D6h
0D5h
0D4h
0D3h
0D2h
0D1h
0D0h
0CFh
0CEh
0CDh
007h
006h
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
PRODUCT PREVIEW
PERIPHERALS WITH BYTE ACCESS
SD16_A
(see also:
Peripherals with
Word Access)
19
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
peripheral file map (continued)
PRODUCT PREVIEW
PERIPHERALS WITH BYTE ACCESS (CONTINUED)
USCI_B1
USCI_B1 transmit buffer
USCI_B1 receive buffer
USCI_B1 status
USCI_B1 I2C interrupt enable
USCI_B1 bit rate control 1
USCI_B1 bit rate control 0
USCI_B1 control 1
USCI_B1 control 0
USCI_A1 interrupt flag
USCI_A1 interrupt enable
UCB1TXBUF
UCB1RXBUF
UCB1STAT
UCB1I2CIE
UCB1BR1
UCB1BR0
UCB1CTL1
UCB1CTL0
UC1IFG
UC1IE
0DFh
0DEh
0DDh
0DCh
0DBh
0DAh
0D9h
0D8h
007h
006h
Comparator_A
p
_
Comparator_A port disable
CAPD
05Bh
Comparator_A control2
CACTL2
05Ah
Comparator_A control1
CACTL1
059h
BrownOUT, SVS
SVS control register (Reset by brownout signal)
SVSCTL
056h
FLL+ Clock
FLL+ Control2
FLL_CTL2
055h
FLL+ Control1
FLL_CTL1
054h
FLL+ Control0
FLL_CTL0
053h
System clock frequency control
SCFQCTL
052h
System clock frequency integrator
SCFI1
051h
System clock frequency integrator
SCFI0
050h
Basic Timer1
BT counter2
BT counter1
BT control
BTCNT2
BTCNT1
BTCTL
047h
046h
040h
Port P10
Port P10 resistor enable
P10REN
017h
Port P10 selection
P10SEL
00Fh
Port P10 direction
P10DIR
00Dh
Port P10 output
P10OUT
00Bh
Port P10 input
P10IN
009h
Port P9 resistor enable
P9REN
016h
Port P9 selection
P9SEL
00Eh
Port P9 direction
P9DIR
00Ch
Port P9 output
P9OUT
00Ah
Port P9 input
P9IN
008h
Port P8 resistor enable
P8REN
015h
Port P8 selection
P8SEL
03Fh
Port P8 direction
P8DIR
03Dh
Port P8 output
P8OUT
03Bh
Port P8 input
P8IN
039h
Port P7 resistor enable
P7REN
014h
Port P7 selection
P7SEL
03Eh
Port P7 direction
P7DIR
03Ch
Port P7 output
P7OUT
03Ah
Port P7 input
P7IN
038h
Port P9
Port P8
Port P7
20
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
peripheral file map (continued)
Port P4
Port P3
Port P2
Port P1
Special
p
functions
Port P5 resistor enable
P5REN
012h
Port P5 selection
P5SEL
033h
Port P5 direction
P5DIR
032h
Port P5 output
P5OUT
031h
Port P5 input
P5IN
030h
Port P4 resistor enable
P4REN
011h
Port P4 selection
P4SEL
01Fh
Port P4 direction
P4DIR
01Eh
Port P4 output
P4OUT
01Dh
Port P4 input
P4IN
01Ch
Port P3 resistor enable
P3REN
010h
Port P3 selection
P3SEL
01Bh
Port P3 direction
P3DIR
01Ah
Port P3 output
P3OUT
019h
Port P3 input
P3IN
018h
Port P2 resistor enable
P2REN
02Fh
Port P2 selection
P2SEL
02Eh
Port P2 interrupt enable
P2IE
02Dh
Port P2 interrupt-edge select
P2IES
02Ch
Port P2 interrupt flag
P2IFG
02Bh
Port P2 direction
P2DIR
02Ah
Port P2 output
P2OUT
029h
Port P2 input
P2IN
028h
Port P1 resistor enable
P1REN
027h
Port P1 selection
P1SEL
026h
Port P1 interrupt enable
P1IE
025h
Port P1 interrupt-edge select
P1IES
024h
Port P1 interrupt flag
P1IFG
023h
Port P1 direction
P1DIR
022h
Port P1 output
P1OUT
021h
Port P1 input
P1IN
020h
SFR interrupt flag2
IFG2
003h
SFR interrupt flag1
IFG1
002h
SFR interrupt enable2
IE2
001h
SFR interrupt enable1
IE1
000h
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
PRODUCT PREVIEW
PERIPHERALS WITH BYTE ACCESS (CONTINUED)
Port P5
21
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
APPLICATION INFORMATION
Port P1, P1.0 to P1.5, input/output with Schmitt-trigger
Pad Logic
DVSS
DVSS
CAPD.x
P1REN.x
P1DIR.x
0
PRODUCT PREVIEW
P1OUT.x
0
1
0
DVCC
1
Bus
Keeper
P1SEL.x
EN
P1IN.x
EN
Module X IN
D
P1IE.x
P1IRQ.x
EN
Q
P1IFG.x
P1SEL.x
P1IES.x
22
1
Direction
0: Input
1: Output
1
Module X OUT
DVSS
Set
Interrupt
Edge
Select
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
P1.0/TA0
P1.1/TA0/MCLK
P1.2/TA1
P1.3/TBOUTH/SVSOUT
P1.4/TBCLK/SMCLK
P1.5/TACLK/ACLK
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
Port P1 (P1.0 to P1.5) pin functions
P1.0/TA0
CONTROL BITS / SIGNALS
X
0
FUNCTION
P1.0 (I/O)
Timer_A3.CCI0A
P1.1/TA0/MCLK
1
2
3
4
5
1
0
1
1
0
X
1
P1.1 (I/O)
I: 0; O: 1
0
0
Timer_A3.CCI0B
0
1
0
MCLK
1
1
0
P1.2 (I/O)
X
X
1
I: 0; O: 1
0
0
0
1
0
Timer_A3.TA1
1
1
0
Input buffer disabled (see Note 2)
X
X
1
I: 0; O: 1
0
0
Timer_B7.TBOUTH
0
1
0
SVSOUT
1
1
0
P1.3 (I/O)
P1.4 (I/O)
Timer_B7.TBCLK
P1.5/TACLK/ACLK
0
0
X
Input buffer disabled (see Note 2)
P1.4/TBCLK/SMCLK
CAPD.x
0
Input buffer disabled (see Note 2)
Timer_A3.CCI1A
P1.3/
TBOUTH/SVSOUT
P1SEL.x
I: 0; O: 1
Timer_A3.TA0
Input buffer disabled (see Note 2)
P1.2/TA1
P1DIR.x
X
X
1
I: 0; O: 1
0
0
0
1
0
SMCLK
1
1
0
Input buffer disabled (see Note 2)
X
X
1
I: 0; O: 1
0
0
Timer_A3.TACLK
0
1
0
ACLK
1
1
0
Input buffer disabled (see Note 2)
X
X
1
P1.5 (I/O)
NOTES: 1. X: Don’t care.
2. Setting the CAPD.x bit disables the output driver as well as the input schmitt trigger to prevent parasitic cross currents when applying
analog signals.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
23
PRODUCT PREVIEW
(P1 X)
PIN NAME (P1.X)
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
Port P1, P1.6, P1.7, input/output with Schmitt-trigger
Pad Logic
To Comparator_A
From Comparator_A
CAPD.x
P1REN.x
P1DIR.x
0
PRODUCT PREVIEW
0
Module X OUT
1
0
1
1
Direction
0: Input
1: Output
1
P1OUT.x
DVSS
DVCC
P1.6/CA0
P1.7/CA1
Bus
Keeper
P1SEL.x
EN
P1IN.x
EN
Module X IN
D
P1IE.x
P1IRQ.x
EN
Q
P1IFG.x
Set
Interrupt
Edge
Select
P1SEL.x
P1IES.x
Port P1 (P1.6 and P1.7) pin functions
PIN NAME (P1.X)
(P1 X)
P1.6/CA0
CONTROL BITS / SIGNALS
X
6
FUNCTION
P1DIR.x
P1.6 (I/O)
CA0 (see Note 2)
P1.7/CA1
7
P1.7 (I/O)
CA1 (see Note 2)
P1SEL.x
CAPD.x
I: 0; O: 1
0
0
X
X
1
I: 0; O: 1
0
0
X
X
1
NOTES: 1. X: Don’t care.
2. Setting the CAPD.x bit disables the output driver as well as the input schmitt trigger to prevent parasitic cross currents when applying
analog signals.
24
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
port P2, P2.0, P2.6 to P2.7, input/output with Schmitt-trigger
Pad Logic
DVSS
DVSS
DVSS
P2REN.x
0
0
Module X OUT
1
1
1
Direction
0: Input
1: Output
1
P2OUT.x
0
Bus
Keeper
P2SEL.x
P2.0/TA2
P2.6/CAOUT
P2.7
PRODUCT PREVIEW
P2DIR.x
DVSS
DVCC
EN
P2IN.x
EN
Module X IN
D
P2IE.x
EN
P2IRQ.x
Q
Set
P2IFG.x
Interrupt
Edge
Select
P2SEL.x
P2IES.x
Port P2 (P2.0, P2.6 and P2.7) pin functions
PIN NAME (P2.X)
(P2 X)
P2.0/TA2
P2.6/CAOUT
P2.7
CONTROL BITS / SIGNALS
X
0
6
7
FUNCTION
P2.0 (I/O)
P2DIR.x
P2SEL.x
I: 0; O: 1
0
Timer_A3.CCI2A
0
1
Timer_A3.TA2
1
1
P2.6 (I/O)
I: 0; O: 1
0
N/A
0
1
CAOUT
1
1
P2.7 (I/O)
I: 0; O: 1
0
N/A
0
1
DVSS
1
1
NOTES: 1. N/A: Not available or not applicable
2. Setting TBOUTH causes all Timer_B outputs to be set to high impedance.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
25
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
port P2, P2.1 to P2.3, input/output with Schmitt-trigger
Timer_B Output Tristate Logic
P1.3/TBOUTH/SVSOUT
P1SEL.3
P1DIR.3
P2REN.x
P2DIR.x
0
PRODUCT PREVIEW
0
Module X OUT
1
0
1
1
Direction
0: Input
1: Output
1
P2OUT.x
DVSS
DVCC
Bus
Keeper
P2SEL.x
P2.1/TB0
P2.2/TB1
P2.3/TB2
EN
P2IN.x
EN
Module X IN
D
P2IE.x
P2IRQ.x
EN
Q
P2IFG.x
P2SEL.x
P2IES.x
Set
Interrupt
Edge
Select
Port P2 (P2.1 to P2.3) pin functions
PIN NAME (P2.X)
(P2 X)
P2.1/TB0
P2.2/TB1
P2.3/TB3
CONTROL BITS / SIGNALS
X
1
2
3
FUNCTION
P2.1 (I/O)
P2SEL.x
I: 0; O: 1
0
Timer_B7.CCI0A and Timer_B7.CCI0B
0
1
Timer_B7.TB0 (see Note 2)
1
1
P2.2 (I/O)
I: 0; O: 1
0
Timer_B7.CCI1A and Timer_B7.CCI1B
0
1
Timer_B7.TB1 (see Note 2)
1
1
P2.3 (I/O)
I: 0; O: 1
0
Timer_B7.CCI2A and Timer_B7.CCI2B
0
1
Timer_B7.TB3 (see Note 2)
1
1
NOTES: 1. N/A: Not available or not applicable
2. Setting TBOUTH causes all Timer_B outputs to be set to high impedance.
26
P2DIR.x
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
port P2, P2.4 to P2.5, input/output with Schmitt-trigger
DVSS
P2REN.x
P2DIR.x
USCI Direction
Control
0
P2OUT.x
0
Module X OUT
1
DVSS
0
DVCC
1
1
Direction
0: Input
1: Output
1
Bus
Keeper
P2SEL.x
P2.4/UCA0TXD/UCA0SIMO
P2.5/UCA0RXD/UCA0SOMI
PRODUCT PREVIEW
EN
P2IN.x
EN
Module X IN
D
P2IE.x
P2IRQ.x
EN
Q
P2IFG.x
P2SEL.x
P2IES.x
Set
Interrupt
Edge
Select
Port P2 (P2.4 and P2.5) pin functions
CONTROL BITS / SIGNALS
PIN NAME (P2.X)
(P2 X)
X
P2.4/
UCA0TXD/UCA0SIMO
4
P2.5/
UCA0RXD/UCA0SOMI
5
FUNCTION
P2.4 (I/O)
UCA0TXD/UCA0SIMO (see Note 1, 2)
P2.5 (I/O)
UCA0RXD/UCA0SOMI (see Note 1, 2)
P2DIR.x
P2SEL.x
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
NOTES: 1. X: Don’t care.
2. The pin direction is controlled by the USCI module.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
27
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
port P3, P3.0 to P3.3, input/output with Schmitt-trigger
Pad Logic
DVSS
P3REN.x
P3DIR.x
USCI Direction
Control
0
P3OUT.x
0
Module X OUT
1
0
1
1
Direction
0: Input
1: Output
1
Bus
Keeper
P3SEL.x
P3.0/UCB0STE/UCA0CLK
P3.1/UCB0SIMO/UCB0SDA
P3.2/UCB0SOMI/UCB0SCL
P3.3/UCB0CLK/UCA0STE
EN
P3IN.x
PRODUCT PREVIEW
DVSS
DVCC
EN
Module X IN
D
Port P3 (P3.0 to P3.3) pin functions
PIN NAME (P3.X)
(P3 X)
CONTROL BITS / SIGNALS
X
P3.0/
UCA0CLK/UCB0STE
0
P3.1/
UCB0SIMO/
UCB0SDA
1
P3.2/
UCB0SOMI/
UCB0SCL
2
P3.3/
UCB0CLK/UCA0STE
3
FUNCTION
P3.0 (I/O)
UCA0CLK/UCB0STE (see Notes 1, 2, 3)
P3.1 (I/O)
UCB0SIMO/UCB0SDA (see Notes 1, 2, 4)
P3.2 (I/O)
UCB0SOMI/UCB0SCL (see Notes 1, 2, 4)
P3.3 (I/O)
UCB0CLK (see Notes 1, 2, 5)
P3DIR.x
P3SEL.x
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
NOTES: 1. X: Don’t care.
2. The pin direction is controlled by the USCI module.
3. UCA0CLK function takes precedence over UCB0STE function. If the pin is required as UCA0CLK input or output USCI_B0 will be
forced to 3-wire SPI mode even if 4-wire SPI mode is selected.
4. In case the I2C functionality is selected the output drives only the logical 0 to VSS level.
5. UCB0CLK function takes precedence over UCA0STE function. If the pin is required as UCB0CLK input or output USCI_A0 will be
forced to 3-wire SPI mode even if 4-wire SPI mode is selected.
28
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
port P3, P3.4 to P3.7, input/output with Schmitt-trigger
Pad Logic
DVSS
P3REN.x
P3DIR.x
0
0
Module X OUT
1
0
1
1
Direction
0: Input
1: Output
1
P3OUT.x
DVSS
DVCC
Bus
Keeper
P3SEL.x
P3.4
P3.5
P3.6
P3.7
EN
P3IN.x
Module X IN
PRODUCT PREVIEW
EN
D
Port P3 (P3.4 to P3.7) pin functions
PIN NAME (P3.X)
(P3 X)
P3.4
P3.5
P3.6
P3.7
CONTROL BITS / SIGNALS
X
4
5
6
7
FUNCTION
P3DIR.x
P3SEL.x
I: 0; O: 1
0
N/A
0
1
DVSS
1
1
I: 0; O: 1
0
N/A
0
1
DVSS
1
1
P3.4 (I/O)
P3.5 (I/O)
P3.6 (I/O)
I: 0; O: 1
0
N/A
0
1
DVSS
1
1
P3.7 (I/O)
I: 0; O: 1
0
N/A
0
1
DVSS
1
1
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
29
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
port P4, P4.0 to P4.1, input/output with Schmitt-trigger
Pad Logic
DVSS
P4REN.x
P4DIR.x
USCI Direction
Control
0
P4OUT.x
0
Module X OUT
1
0
1
1
Direction
0: Input
1: Output
1
Bus
Keeper
P4SEL.x
P4.0/UCA1TXD/UCA1SIMO
P4.1/UCA1RXD/UCA1SOMI
EN
P4IN.x
PRODUCT PREVIEW
DVSS
DVCC
EN
Module X IN
D
Port P4 (P4.0 to P4.1) pin functions
CONTROL BITS / SIGNALS
PIN NAME (P4.X)
(P4 X)
X
P4.0/
UCA1TXD/UCA1SIMO
0
P4.1/
UCA1RXD/UCA1SOMI
1
FUNCTION
P4.0 (I/O)
UCA1TXD/UCA1SIMO (see Notes 1, 2)
P4.1 (I/O)
UCA1RXD/UCA1SOMI (see Notes 1, 2)
NOTES: 1. X: Don’t care.
2. The pin direction is controlled by the USCI module.
30
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
P4DIR.x
P4SEL.x
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
port P4, P4.2 to P4.5, input/output with Schmitt-trigger
Pad Logic
Segment Sz
LCDS...
P4REN.x
0
P4OUT.x
0
Module X OUT
1
0
1
1
Direction
0: Input
1: Output
1
P4.2/UCB1STE/UCA1CLK/S39
P4.3/UCB1SIMO/UCB1SDA/S38
P4.4/UCB1SOMI/UCB1SCL/S37
P4.5/UCB1CLK/UCA1STE/S36
Bus
Keeper
P4SEL.x
PRODUCT PREVIEW
P4DIR.x
USCI Direction
Control
DVSS
DVCC
EN
P4IN.x
EN
Module X IN
D
Port P4 (P4.2 to P4.5) pin functions
CONTROL BITS / SIGNALS
PIN NAME (P4.X)
(P4 X)
X
P4.2/
UCA1CLK/UCB1STE/
S39
2
P4.3/
UCB1SIMO/UCB1SDA/
S38
3
P4.4/
UCB1SOMI/UCB1SCL/
S37
4
P4.5/
UCB1CLK/UCA1STE/
S36
5
FUNCTION
P4.2 (I/O)
P4DIR.x
P4SEL.x
LCDS36
I: 0; O: 1
0
0
UCA1CLK/UCB1STE (see Notes 2, 3)
X
1
0
S39
X
X
1
P4.3 (I/O)
I: 0; O: 1
0
0
UCB1SIMO/UCB1SDA (see Notes 2, 4)
X
1
0
S38
X
X
1
P4.4 (I/O)
I: 0; O: 1
0
0
UCB1SOMI/UCB1SCL (see Notes 2, 4)
X
1
0
S37
X
X
1
P4.5 (I/O)
I: 0; O: 1
0
0
UCB1CLK/UCA1STE (see Notes 2, 5)
X
1
0
S36
X
X
1
NOTES: 1. X: Don’t care.
2. The pin direction is controlled by the USCI module.
3. UCA1CLK function takes precedence over UCB1STE function. If the pin is required as UCA1CLK input or output USCI_B1 will be
forced to 3-wire SPI mode even if 4-wire SPI mode is selected.
4. In case the I2C functionality is selected the output drives only the logical 0 to VSS level.
5. UCB1CLK function takes precedence over UCA1STE function. If the pin is required as UCB1CLK input or output USCI_A1 will be
forced to 3-wire SPI mode even if 4-wire SPI mode is selected.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
31
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
port P4, P4.6 to P4.7, input/output with Schmitt-trigger
Pad Logic
Segment Sz
LCDS...
P4REN.x
P4DIR.x
0
PRODUCT PREVIEW
0
Module X OUT
1
0
1
1
Direction
0: Input
1: Output
1
P4OUT.x
DVSS
DVCC
P4.6/S35
P4.7/S34
Bus
Keeper
P4SEL.x
EN
P4IN.x
EN
Module X IN
D
Port P4 (P4.6 to P4.7) pin functions
PIN NAME (P4.X)
(P4 X)
CONTROL BITS / SIGNALS
X
P4.6/S35
6
P4.7/S34
7
FUNCTION
P4.6 (I/O)
S35
P4.7 (I/O)
S34
NOTES: 1. X: Don’t care.
32
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
P4DIR.x
P4SEL.x
LCDS32
I: 0; O: 1
0
0
X
X
1
I: 0; O: 1
0
0
X
X
1
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
port P5, P5.0, input/output with Schmitt-trigger
Pad Logic
To SVS
P5REN.x
DVSS
DVCC
0
1
P5OUT.x
DVSS
1
Direction
0: Input
1: Output
0
1
P5.0/SVSIN
Bus
Keeper
EN
P5SEL.x
P5IN.x
Port P5 (P5.0) pin functions
PIN NAME (P5.X)
(P5 X)
P5.0/SVSIN
CONTROL BITS / SIGNALS
X
0
FUNCTION
P5DIR.x
P5SEL.x
P5.0 (I/O) (see Note 1)
I: 0; O: 1
0
SVSIN (see Notes 1, 3)
X
1
NOTES: 1. X: Don’t care.
2. N/A: Not available or not applicable.
3. Setting the P5SEL.x bit disables the output driver as well as the input Schmitt trigger to prevent parasitic cross currents when
applying analog signals.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
33
PRODUCT PREVIEW
P5DIR.x
0
1
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
port P5, P5.1, input/output with Schmitt-trigger
Pad Logic
Segment S0
LCDS0
P5REN.1
P5DIR.1
0
PRODUCT PREVIEW
0
Module X OUT
1
0
1
1
Direction
0: Input
1: Output
1
P5OUT.1
DVSS
DVCC
P5.1/S0
Bus
Keeper
P5SEL.1
EN
P5IN.1
EN
Module X IN
D
Port P5 (P5.1) pin functions
PIN NAME (P5.X)
(P5 X)
P5.1/S0
CONTROL BITS / SIGNALS
X
1
FUNCTION
P5DIR.x
P5SEL.x
LCDS0
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S0
X
X
1
P5.1 (I/O)
NOTES: 1. X: Don’t care.
2. N/A: Not available or not applicable.
34
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
port P5, P5.2 to P5.7, input/output with Schmitt-trigger
Pad Logic
LCD Signal
P5REN.x
0
0
DVSS
1
1
1
Direction
0: Input
1: Output
1
P5OUT.x
0
Bus
Keeper
P5SEL.x
EN
P5IN.x
P5.2/COM1
P5.3/COM2
P5.4/COM3
P5.5/R03
P5.6/LCDREF/R13
P5.7/R03
PRODUCT PREVIEW
P5DIR.x
DVSS
DVCC
Port P5 (P5.2 to P5.4) pin functions
PIN NAME (P5.X)
(P5 X)
CONTROL BITS / SIGNALS
X
P5.2/COM1
2
P5.3/COM2
3
P5.4/COM3
4
FUNCTION
P5.2 (I/O)
COM1 (see Note 2)
P5.3 (I/O)
COM2 (see Note 2)
P5.4 (I/O)
COM3 (see Note 2)
P5.5/R03
5
P5.5 (I/O)
R03 (see Note 2)
P5.6/LCDREF/R13
6
P5.7/R03
7
P5.6 (I/O)
R13 or LCDREF (see Notes 2, 3)
P5.7 (I/O)
R03 (see Note 2)
P5DIR.x
P5SEL.x
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
NOTES: 1. X: Don’t care.
2. Setting the P5SEL.x bit disables the output driver as well as the input Schmitt trigger to prevent parasitic cross currents when
applying analog signals.
3. External reference for the LCD_A charge pump is applied when VLCDREFx = 01. Otherwise R13 is selected.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
35
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
port P7 to port P10, input/output with Schmitt-trigger
Pad Logic
Segment Sz
LCDS...
PyREN.x
PyDIR.x
0
0
Module X OUT
1
1
EN
PyIN.x
EN
Module X IN
36
1
Py.x/Sz
Bus
Keeper
PySEL.x
PRODUCT PREVIEW
0
Direction
0: Input
1: Output
1
PyOUT.x
DVSS
DVCC
D
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
Port P7 (P7.0 to P7.1) pin functions
(P7 X)
PIN NAME (P7.X)
P7.0/S33
CONTROL BITS / SIGNALS
X
0
FUNCTION
P7.0 (I/O)
S33
P7.1/S32
1
P7.1 (I/O)
S32
P7DIR.x
P7SEL.x
LCDS32
I: 0; O: 1
0
0
X
X
1
I: 0; O: 1
0
0
X
X
1
NOTES: 1. X: Don’t care.
Port P7 (P7.4 to P7.5) pin functions
P7.2/S31
CONTROL BITS / SIGNALS
X
2
FUNCTION
P7.2 (I/O)
S31
P7.3/S30
3
P7.3 (I/O)
S30
P7.4/S29
4
P7.5/S28
5
P7.4 (I/O)
S29
P7.5 (I/O)
S28
P7DIR.x
P7SEL.x
LCDS28
I: 0; O: 1
0
0
X
X
1
I: 0; O: 1
0
0
X
X
1
I: 0; O: 1
0
0
X
X
1
I: 0; O: 1
0
0
X
X
1
PRODUCT PREVIEW
PIN NAME (P7.X)
(P7 X)
NOTES: 1. X: Don’t care.
Port P7 (P7.6 to P7.7) pin functions
PIN NAME (P7.X)
(P7 X)
CONTROL BITS / SIGNALS
X
P7.6/S27
6
P7.7/S26
7
FUNCTION
P7.6 (I/O)
S27
P7.7 (I/O)
S26
P7DIR.x
P7SEL.x
LCDS24
I: 0; O: 1
0
0
X
X
1
I: 0; O: 1
0
0
X
X
1
NOTES: 1. X: Don’t care.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
37
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
Port P8 (P8.0 to P8.1) pin functions
(P8 X)
PIN NAME (P8.X)
P8.0/S25
CONTROL BITS / SIGNALS
X
0
FUNCTION
P8.0 (I/O)
S25
P8.1/S24
1
P8.0 (I/O)
S24
P8DIR.x
P8SEL.x
LCDS24
I: 0; O: 1
0
0
X
X
1
I: 0; O: 1
0
0
X
X
1
NOTES: 1. X: Don’t care.
Port P8 (P8.2 to P8.5) pin functions
PIN NAME (P8.X)
(P8 X)
P8.2/S23
CONTROL BITS / SIGNALS
X
2
FUNCTION
P8.2 (I/O)
S23
P8.3/S22
3
P8.3 (I/O)
PRODUCT PREVIEW
S22
P8.4/S21
4
P8.5/S20
5
P8.4 (I/O)
S21
P8.5 (I/O)
S23
P8DIR.x
P8SEL.x
LCDS20
I: 0; O: 1
0
0
X
X
1
I: 0; O: 1
0
0
X
X
1
I: 0; O: 1
0
0
X
X
1
I: 0; O: 1
0
0
X
X
1
NOTES: 1. X: Don’t care.
Port P8 (P8.6 to P8.7) pin functions
PIN NAME (P8.X)
(P8 X)
CONTROL BITS / SIGNALS
X
P8.6/S19
6
P8.7/S18
7
FUNCTION
P8.6 (I/O)
S19
P8.7 (I/O)
S18
NOTES: 1. X: Don’t care.
38
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
P8DIR.x
P8SEL.x
LCDS16
I: 0; O: 1
0
0
X
X
1
I: 0; O: 1
0
0
X
X
1
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
Port P9 (P9.0 to P9.1) pin functions
(P9 X)
PIN NAME (P9.X)
P9.0/S17
CONTROL BITS / SIGNALS
X
0
FUNCTION
P9.0 (I/O)
S17 (see Note 1)
P9.1/S16
1
P9.1 (I/O)
S16 (see Note 1)
P9DIR.x
P9SEL.x
LCDS16
I: 0; O: 1
0
0
X
X
1
I: 0; O: 1
0
0
X
X
1
NOTES: 1. X: Don’t care.
Port P9 (P9.2 to P9.5) pin functions
P9.2/S15
CONTROL BITS / SIGNALS
X
2
FUNCTION
P9.2 (I/O)
S15
P9.3/S14
3
P9.3 (I/O)
S14
P9.4/S13
4
P9.5/S12
5
P9.4 (I/O)
S13
P9.5 (I/O)
S12
P9DIR.x
P9SEL.x
LCDS12
I: 0; O: 1
0
0
X
X
1
I: 0; O: 1
0
0
X
X
1
I: 0; O: 1
0
0
X
X
1
I: 0; O: 1
0
0
X
X
1
PRODUCT PREVIEW
PIN NAME (P9.X)
(P9 X)
NOTES: 1. X: Don’t care.
Port P9 (P9.6 to P9.7) pin functions
PIN NAME (P9.X)
(P9 X)
CONTROL BITS / SIGNALS
X
P9.6/S11
6
P9.7/S10
7
FUNCTION
P9.6 (I/O)
S11
P9.7 (I/O)
S10
P9DIR.x
P9SEL.x
LCDS8
I: 0; O: 1
0
0
X
X
1
I: 0; O: 1
0
0
X
X
1
NOTES: 1. X: Don’t care.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
39
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
Port P10 (P10.0 to P10.1) pin functions
(P10 X)
PIN NAME (P10.X)
P10.0/S8
CONTROL BITS / SIGNALS
X
0
FUNCTION
P10.0 (I/O)
S8
P10.1/S7
1
P10.1 (I/O)
S7
P10DIR.x
P10SEL.x
LCDS8
I: 0; O: 1
0
0
X
X
1
I: 0; O: 1
0
0
X
X
1
NOTES: 1. X: Don’t care.
Port P10 (P10.2 to P10.5) pin functions
PIN NAME (P10.X)
(P10 X)
P10.2/S7
CONTROL BITS / SIGNALS
X
2
FUNCTION
P10.2 (I/O)
S7
P10.3/S6
3
P10.3 (I/O)
PRODUCT PREVIEW
S6
P10.4/S5
4
P10.5/S4
5
P10.4 (I/O)
S5
P10.5 (I/O)
S4
P10DIR.x
P10SEL.x
LCDS4
I: 0; O: 1
0
0
X
X
1
I: 0; O: 1
0
0
X
X
1
I: 0; O: 1
0
0
X
X
1
I: 0; O: 1
0
0
X
X
1
NOTES: 1. X: Don’t care.
Port P10 (P10.6 to P10.7) pin functions
PIN NAME (P10.X)
(P10 X)
CONTROL BITS / SIGNALS
X
P10.6/S3
6
P10.7/S2
7
FUNCTION
P10.6 (I/O)
S3
P10.7 (I/O)
S2
NOTES: 1. X: Don’t care.
40
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
P10DIR.x
P10SEL.x
LCDS0
I: 0; O: 1
0
0
X
X
1
I: 0; O: 1
0
0
X
X
1
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
JTAG pins TMS, TCK, TDI/TCLK, TDO/TDI, input/output with Schmitt-trigger or output
TDO
Controlled by JTAG
Controlled by JTAG
TDO/TDI
JTAG
Controlled
by JTAG
DVCC
TDI
Burn and Test
Fuse
Emulation
PRODUCT PREVIEW
TDI/TCLK
Test
and
DVCC
TMS
Module
TMS
DVCC
TCK
TCK
RST/NMI
Tau ~ 50 ns
Brownout
TCK
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
G
D
U
S
G
D
U
S
41
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
JTAG fuse check mode
MSP430 devices that have the fuse on the TDI/TCLK terminal have a fuse check mode that tests the continuity
of the fuse the first time the JTAG port is accessed after a power-on reset (POR). When activated, a fuse check
current (I(TF) ) of 1 mA at 3 V can flow from the TDI/TCLK pin to ground if the fuse is not burned. Care must be
taken to avoid accidentally activating the fuse check mode and increasing overall system power consumption.
Activation of the fuse check mode occurs with the first negative edge on the TMS pin after power up or if the
TMS is being held low during power up. The second positive edge on the TMS pin deactivates the fuse check
mode. After deactivation, the fuse check mode remains inactive until another POR occurs. After each POR the
fuse check mode has the potential to be activated.
The fuse check current only flows when the fuse check mode is active and the TMS pin is in a low state (see
Figure 1). Therefore, the additional current flow can be prevented by holding the TMS pin high (default
condition). The JTAG pins are terminated internally and therefore do not require external termination.
Time TMS Goes Low After POR
TMS
PRODUCT PREVIEW
ITDI/TCLK
I(TF)
Figure 1. Fuse Check Mode Current MSP430x47x3, MSP430x47x4
42
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MSP430x47x3, MSP430x47x4
MIXED SIGNAL MICROCONTROLLER
SLAS545 − MAY 2007
Data Sheet Revision History
Literature
Number
SLAS545
Summary
Preliminary PRODUCT PREVIEW datasheet release.
PRODUCT PREVIEW
NOTE: The referring page and figure numbers are referred to the respective document revision.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
43
PACKAGE OPTION ADDENDUM
www.ti.com
15-Oct-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
MSP430F4783IPZ
PREVIEW
LQFP
PZ
100
50
TBD
Call TI
Call TI
MSP430F4784IPZ
PREVIEW
LQFP
PZ
100
50
TBD
Call TI
Call TI
MSP430F4793IPZ
PREVIEW
LQFP
PZ
100
50
TBD
Call TI
Call TI
MSP430F4794IPZ
PREVIEW
LQFP
PZ
100
50
TBD
Call TI
Call TI
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
MECHANICAL DATA
MTQF013A – OCTOBER 1994 – REVISED DECEMBER 1996
PZ (S-PQFP-G100)
PLASTIC QUAD FLATPACK
0,27
0,17
0,50
75
0,08 M
51
76
50
100
26
1
0,13 NOM
25
12,00 TYP
Gage Plane
14,20
SQ
13,80
16,20
SQ
15,80
0,05 MIN
1,45
1,35
0,25
0°– 7°
0,75
0,45
Seating Plane
0,08
1,60 MAX
4040149 /B 11/96
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-026
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties
may be subject to additional restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Telephony
www.ti.com/telephony
Low Power
Wireless
www.ti.com/lpw
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated