ELPIDA HB54A2568KN-10B

PRELIMINARY DATA SHEET
256MB DDR SDRAM S.O.DIMM
HB54A2568KN-A75B/B75B/10B (32M words × 64 bits, 2 Banks)
Description
Features
The HB54A2568KN is Double Data Rate (DDR)
SDRAM Module, mounted 256M bits DDR SDRAM
(HM5425161BTT) sealed in TSOP package, and 1
piece of serial EEPROM (2k bits EEPROM) for
Presence Detect (PD).
The HB54A2568KN is
organized as 16M × 64 × 2 bank mounted 8 pieces of
256M bits DDR SDRAM. Read and write operations
are performed at the cross points of the CK and the
/CK. This high-speed data transfer is realized by the 2
bits prefetch-pipelined architecture. Data strobe (DQS)
both for read and write are available for high speed and
reliable data bus design. By setting extended mode
register, the on-chip Delay Locked Loop (DLL) can be
set enable or disable. An outline of the products is
200-pin socket type package (dual lead out).
Therefore, it makes high density mounting possible
without surface mount technology. It provides common
data inputs and outputs. Decoupling capacitors are
mounted beside each TSOP on the module board.
• 200-pin socket type package (dual lead out)
 Outline: 67.6mm (Length) × 31.75mm (Height) ×
3.80mm (Thickness)
 Lead pitch: 0.6mm
• 2.5V power supply (VCC)
• SSTL-2 interface for all inputs and outputs
• Clock frequency: 133 MHz (max) (-A75B/B75B)
: 100 MHz (max) (-10B)
• Data inputs, outputs and DM are synchronized with
DQS
• 4 banks can operate simultaneously and
independently (Component)
• Burst read/write operation
• Programmable burst length: 2, 4, 8
 Burst read stop capability
• Programmable burst sequence
 Sequential
 Interleave
• Start addressing capability
 Even and Odd
• Programmable /CAS latency (CL): 2, 2.5
• 8192 refresh cycles: 7.8µs (8192row /64ms)
• 2 variations of refresh
 Auto refresh
 Self refresh
Document No. E0148H20 (Ver. 2.0)
Date Published April 2002 (K) Japan
URL: http://www.elpida.com
Elpida Memory, Inc. 2001-2002
Hitachi, Ltd. 2001
Elpida Memory, Inc. is a joint venture DRAM company of NEC Corporation and Hitachi, Ltd.
HB54A2568KN-A75B/B75B/10B
Ordering Information
Part number
Clock frequency
MHz (max.)
/CAS latency
Package
HB54A2568KN-A75B*1
HB54A2568KN-B75B*2
HB54A2568KN-10B*3
133 MHz
133 MHz
100 MHz
2.0
2.5
2.0
200-pin dual lead out socket Gold
type
Contact pad
Notes: 1. 143 MHz operation at /CAS latency = 2.5.
2. 100 MHz operation at /CAS latency = 2.0.
3. 125 MHz operation at /CAS latency = 2.5.
Pin Configurations
Front side
1 pin
39 pin 41 pin
199 pin
2 pin
40 pin 42 pin
200 pin
Back side
Pin No.
Pin name
Pin No.
Pin name
Pin No.
Pin name
Pin No.
Pin name
1
VREF
51
VSS
2
VREF
52
VSS
3
VSS
53
DQ19
4
VSS
54
DQ23
5
DQ0
55
DQ24
6
DQ4
56
DQ28
7
DQ1
57
VCC
8
DQ5
58
VCC
9
VCC
59
DQ25
10
VCC
60
DQ29
11
DQS0
61
DQS3
12
DM0
62
DM3
13
DQ2
63
VSS
14
DQ6
64
VSS
15
VSS
65
DQ26
16
VSS
66
DQ30
17
DQ3
67
DQ27
18
DQ7
68
DQ31
19
DQ8
69
VCC
20
DQ12
70
VCC
21
VCC
71
NC
22
VCC
72
NC
23
DQ9
73
NC
24
DQ13
74
NC
25
DQS1
75
VSS
26
DM1
76
VSS
27
VSS
77
NC
28
VSS
78
NC
29
DQ10
79
NC
30
DQ14
80
NC
31
DQ11
81
VCC
32
DQ15
82
VCC
33
VCC
83
NC
34
VCC
84
NC
35
CK0
85
NC
36
VCC
86
NC
37
/CK0
87
VSS
38
VSS
88
VSS
39
VSS
89
CK2
40
VSS
90
VSS
41
DQ16
91
/CK2
42
DQ20
92
VCC
43
DQ17
93
VCC
44
DQ21
94
VCC
45
VCC
95
CKE1
46
VCC
96
CKE0
47
DQS2
97
NC
48
DM2
98
NC
49
DQ18
99
A12
50
DQ22
100
A11
Preliminary Data Sheet E0148H20 (Ver. 2.0)
2
HB54A2568KN-A75B/B75B/10B
Pin No.
Pin name
Pin No.
Pin name
Pin No.
Pin name
Pin No.
Pin name
101
A9
151
DQ42
102
A8
152
DQ46
103
VSS
153
DQ43
104
VSS
154
DQ47
105
A7
155
VCC
106
A6
156
VCC
107
A5
157
VCC
108
A4
158
/CK1
109
A3
159
VSS
110
A2
160
CK1
111
A1
161
VSS
112
A0
162
VSS
113
VCC
163
DQ48
114
VCC
164
DQ52
115
A10/AP
165
DQ49
116
BA1
166
DQ53
117
BA0
167
VCC
118
/RAS
168
VCC
119
/WE
169
DQS6
120
/CAS
170
DM6
121
/S0
171
DQ50
122
/S1
172
DQ54
123
NC
173
VSS
124
NC
174
VSS
125
VSS
175
DQ51
126
VSS
176
DQ55
127
DQ32
177
DQ56
128
DQ36
178
DQ60
129
DQ33
179
VCC
130
DQ37
180
VCC
131
VCC
181
DQ57
132
VCC
182
DQ61
133
DQS4
183
DQS7
134
DM4
184
DM7
135
DQ34
185
VSS
136
DQ38
186
VSS
137
VSS
187
DQ58
138
VSS
188
DQ62
139
DQ35
189
DQ59
140
DQ39
190
DQ63
141
DQ40
191
VCC
142
DQ44
192
VCC
143
VCC
193
SDA
144
VCC
194
SA0
145
DQ41
195
SCL
146
DQ45
196
SA1
147
DQS5
197
VCCSPD
148
DM5
198
SA2
149
VSS
199
VCCID
150
VSS
200
NC
Preliminary Data Sheet E0148H20 (Ver. 2.0)
3
HB54A2568KN-A75B/B75B/10B
Pin Description
Pin name
Function
A0 to A12
Address input
Row address
Column address
BA0, BA1
Bank select address
DQ0 to DQ63
Data input/output
/RAS
Row address strobe command
/CAS
Column address strobe command
/WE
Write enable
/S0, /S1
Chip select
A0 to A12
A0 to A8
CKE0, CKE1
Clock enable
CK0 to CK2
Clock input
/CK0 to /CK2
Differential clock input
DQS0 to DQS7
Input and output data strobe
DM0 to DM7
Input mask
SCL
Clock input for serial PD
SDA
Data input/output for serial PD
SA0 to SA2
Serial address input
VCC
Power for internal circuit
VCCSPD
Power for serial EEPROM
VREF
Input reference voltage
VSS
Ground
VCCID
VCC identification flag
NC
No connection
Preliminary Data Sheet E0148H20 (Ver. 2.0)
4
HB54A2568KN-A75B/B75B/10B
1
Serial PD Matrix*
Byte No.
0
1
Function described
Number of bytes utilized by module
manufacturer
Total number of bytes in serial PD
device
Bit7
Bit6
Bit5 Bit4
Bit3
Bit2
Bit1 Bit0
Hex value
Comments
1
0
0
0
0
0
0
0
80
128
0
0
0
0
1
0
0
0
08
256 byte
2
Memory type
0
0
0
0
0
1
1
1
07
SDRAM DDR
3
Number of row address
0
0
0
0
1
1
0
1
0D
13
4
Number of column address
0
0
0
0
1
0
0
1
09
9
5
Number of DIMM banks
0
0
0
0
0
0
1
0
02
2
6
Module data width
0
1
0
0
0
0
0
0
40
64 bits
7
Module data width continuation
0
0
0
0
0
0
0
0
00
0 (+)
8
Voltage interface level of this assembly 0
0
0
0
0
1
0
0
04
SSTL 2.5V
9
DDR SDRAM cycle time, CL = X
-A75B
0
1
1
1
0
0
0
0
70
CL = 2.5*5
-B75B
0
1
1
1
0
1
0
1
75
-10B
1
0
0
0
0
0
0
0
80
0
1
1
1
0
0
0
0
70
0.7ns*5
1
0
0
0
0
0
0
0
80
0.8ns*5
10
SDRAM access from clock (tAC)
-A75B/B75B
-10B
11
DIMM configuration type
0
0
0
0
0
0
0
0
00
Non-parity
12
Refresh rate/type
1
0
0
0
0
0
1
0
82
7.8 µs
Self refresh
13
Primary SDRAM width
0
0
0
1
0
0
0
0
10
× 16
14
Error checking SDRAM width
0
0
0
0
0
0
0
0
00
Not used
0
0
0
0
0
0
0
1
01
1 CLK
0
0
0
0
1
1
1
0
0E
2, 4, 8
0
0
0
0
0
1
0
0
04
4
0
0
0
0
1
1
0
0
0C
2, 2.5
0
0
0
0
0
0
0
1
01
0
0
0
0
0
0
0
1
0
02
1
15
16
17
18
19
20
SDRAM device attributes:
Minimum clock delay back-to-back
column access
SDRAM device attributes:
Burst length supported
SDRAM device attributes: Number of
banks on SDRAM device
SDRAM device attributes:
/CAS latency
SDRAM device attributes:
/CS latency
SDRAM device attributes:
/WE latency
21
SDRAM module attributes
0
0
1
0
0
0
0
0
20
Unbuffered
22
SDRAM device attributes: General
1
0
0
0
0
0
0
0
80
± 0.2V
23
Minimum clock cycle time at
CLX - 0.5
-A75B
0
1
1
1
0
1
0
1
75
CL = 2*5
1
0
1
0
0
0
0
0
A0
24
Maximum data access time (tAC) from
0
clock at CLX - 0.5
-A75B/B75B
1
1
1
0
0
0
0
70
0.7ns*5
0
0
0
0
0
0
0
80
0.8ns*5
0
0
0
0
0
0
0
00
0
0
0
0
0
0
0
00
1
0
1
0
0
0
0
50
-B75B/10B
-10B
25
26
27
1
Minimum clock cycle time at
0
CLX - 1
Maximum data access time (tAC) from
0
clock at CLX - 1
Minimum row precharge time (tRP)
0
Preliminary Data Sheet E0148H20 (Ver. 2.0)
5
20ns
HB54A2568KN-A75B/B75B/10B
Byte No.
Function described
Bit7
Bit6
Bit5 Bit4
Bit3
Bit2
Bit1 Bit0
Hex value
Comments
28
Minimum row active to row active
delay (tRRD)
0
0
1
1
1
1
0
0
3C
15ns
29
Minimum /RAS to /CAS delay (tRCD)
0
1
0
1
0
0
0
0
50
20ns
30
Minimum active to precharge time
(tRAS)
-A75B/B75B
0
0
1
0
1
1
0
1
2D
45ns
0
0
1
1
0
0
1
0
32
50ns
-10B
31
Module bank density
0
0
1
0
0
0
0
0
20
1 bank/
2 bank
128 MB
32
Address and command setup time
before clock (tIS)
-A75B/B75B
1
0
1
1
0
0
0
0
B0
1.1ns*5
1
1
0
0
0
0
0
0
C0
1.2ns*5
Address and command hold time after
clock (tIH)
1
-A75B/B75B
0
1
1
0
0
0
0
B0
1.1ns*5
1
1
0
0
0
0
0
0
C0
1.2ns*5
0
1
0
1
0
0
0
0
50
0.5ns*5
0
1
1
0
0
0
0
0
60
0.6ns*5
0
1
0
1
0
0
0
0
50
0.5ns*5
0
1
1
0
0
0
0
0
60
0.6ns*5
-10B
33
-10B
34
Data input setup time before clock
(tDS)
-A75B/B75B
-10B
35
Data input hold time after clock (tDH)
-A75B/B75B
-10B
36 to 40
Superset information
0
0
0
0
0
0
0
0
00
Future use
41
Active command period (tRC)
-A75B/B75B
0
1
0
0
0
0
0
1
41
65ns*5
0
1
0
0
0
1
1
0
46
70ns*5
0
1
0
0
1
0
1
1
4B
75ns*5
0
1
0
1
0
0
0
0
50
80ns*5
-10B
42
Auto refresh to active/
Auto refresh command cycle (tRFC)
-A75B/B75B
-10B
43
SDRAM tCK cycle max. (tCK max.)
0
0
1
1
1
1
0
0
3C
15ns*5
44
Dout to DQS skew
-A75B/B75B
0
0
1
1
0
0
1
0
32
500ps*5
0
0
1
1
1
1
0
0
3C
600ps*5
0
1
1
1
0
1
0
1
75
750ps*5
1
0
1
0
0
0
0
0
A0
1000ps*5
-10B
45
Data hold skew (tQHS)
-A75B/B75B
-10B
46 to 61
Superset information
0
0
0
0
0
0
0
0
00
Future use
62
SPD revision
0
0
0
0
0
0
0
0
00
Initial
Preliminary Data Sheet E0148H20 (Ver. 2.0)
6
HB54A2568KN-A75B/B75B/10B
Byte No.
Function described
Bit7
Bit6
Bit5 Bit4
Bit3
Bit2
Bit1 Bit0
Hex value
Comments
63
Checksum for bytes 0 to 62
-A75B
1
0
0
1
1
0
9C
156
1
0
-B75B
1
1
0
0
1
1
0
0
CC
204
-10B
0
1
1
1
1
0
1
1
7B
123
HITACHI
64
Manufacturer’s JEDEC ID code
0
0
0
0
0
1
1
1
07
65 to 71
Manufacturer’s JEDEC ID code
0
0
0
0
0
0
0
0
00
72
Manufacturing location
×
×
×
×
×
×
×
×
××
*2 (ASCII-8bit
code)
73
Module part number
0
1
0
0
1
0
0
0
48
H
74
Module part number
0
1
0
0
0
0
1
0
42
B
75
Module part number
0
0
1
1
0
1
0
1
35
5
76
Module part number
0
0
1
1
0
1
0
0
34
4
77
Module part number
0
1
0
0
0
0
0
1
41
A
78
Module part number
0
0
1
1
0
0
1
0
32
2
79
Module part number
0
0
1
1
0
1
0
1
35
5
80
Module part number
0
0
1
1
0
1
1
0
36
6
81
Module part number
0
0
1
1
1
0
0
0
38
8
82
Module part number
0
1
0
0
1
0
1
1
4B
K
83
Module part number
0
1
0
0
1
1
1
0
4E
N
84
Module part number
0
0
1
0
1
1
0
1
2D
—
85
Module part number
-A75B
0
1
0
0
0
0
0
1
41
A
-B75B
0
1
0
0
0
0
1
0
42
B
-10B
0
0
1
1
0
0
0
1
31
1
0
0
1
1
0
1
1
1
37
7
0
0
1
1
0
0
0
0
30
0
0
0
1
1
0
1
0
1
35
5
0
1
0
0
0
0
1
0
42
B
0
1
0
0
0
0
1
0
42
B
86
Module part number
-A75B/B75B
87
Module part number
-A75B/B75B
88
Module part number
-A75B/B75B
0
0
1
0
0
0
0
0
20
(Space)
89 to 90
Module part number
0
0
1
0
0
0
0
0
20
(Space)
91
Revision code
0
0
1
1
0
0
0
0
30
Initial
92
Revision code
0
0
1
0
0
0
0
0
20
(Space)
93
Manufacturing date
×
×
×
×
×
×
×
×
××
94
Manufacturing date
×
×
×
×
×
×
×
×
××
-10B
-10B
-10B
3
95 to 98
Module serial number
*
99 to 127
Manufacturer specific data
*4
Preliminary Data Sheet E0148H20 (Ver. 2.0)
7
Year code
(BCD)
Week code
(BCD)
HB54A2568KN-A75B/B75B/10B
Notes: 1. All serial PD data are not protected. 0: Serial data, “driven Low”, 1: Serial data, “driven High” These
SPD are based on JEDEC Committee Ballot JC-42.5-99-129.
2. Byte72 is manufacturing location code. (ex: In case of Japan, byte72 is 4AH. 4AH shows “J” on ASCII
code.)
3. Bytes 95 through 98 are assembly serial number.
4. All bits of 99 through 127 are not defined (“1” or “0”).
5. These specifications are defined based on component specification, not module.
Preliminary Data Sheet E0148H20 (Ver. 2.0)
8
HB54A2568KN-A75B/B75B/10B
Block Diagram
/S1
/S0
RS
DQS0
LDQS
/S
LDQS
RS
/S
DQS4
LDM
DM0
8
RS
DQS1
RS
DM1
8
LDM
DM4
8
RS
DQ0 to DQ7
I/O0 to I/O7
I/O0 to I/O7
UDQS
UDQS
D0
D4
DQS5
DM5
/S
LDQS
DQS3
RS
DM3
8
DQS6
D2
UDQS
D6
UDM
UDM
I/O8 to I/O15
I/O8 to I/O15
/S
LDQS
LDQS
/S
RS
LDM
LDM
I/O0 to I/O7
I/O0 to I/O7
UDQS
UDQS
DM6
D1
LDM
LDM
8
RS
DQ48 to DQ55
D5
I/O0 to I/O7
I/O0 to I/O7
RS
DQS7
D3
UDQS
UDQS
D7
RS
UDM
UDM
DM7
RS
DQ24 to DQ31
I/O0 to I/O7
RS
/S
RS
RS
I/O0 to I/O7
RS
DQ40 to DQ47
I/O8 to I/O15
RS
8
LDM
UDQS
8
LDQS
DM2
LDM
RS
UDM
UDM
RS
DQ16 to DQ23
/S
RS
I/O8 to I/O15
DQS2
LDQS
RS
DQ32 to DQ39
RS
DQ8 to DQ15
/S
LDQS
RS
RS
8
DQ56 to DQ63
I/O8 to I/O15
I/O8 to I/O15
UDM
UDM
I/O8 to I/O15
I/O8 to I/O15
RS
* D0 to D7 : 256M bits DDR SDRAM
U0 : 2k bits EEPROM
Rs : 22Ω
Serial PD
BA0 to BA1
SDRAMs (D0 to D7)
A0 to AN
SDRAMs (D0 to D7)
SCL
SCL
/RAS
SDRAMs (D0 to D7)
SA0
A0
/CAS
SDRAMs (D0 to D7)
SA1
A1
/WE
SDRAMs (D0 to D7)
CKE0
SA2
SDRAMs (D0 to D3)
A2
CKE1
SDA
SDA
U0
WP
SDRAMs (D4 to D7)
VCCSPD
SPD
CK0
/CK0
4 loads
4 loads
VREF
SDRAMs (D0 to D7)
CK1
/CK1
VCC
SDRAMs (D0 to D7), VCC and VCCQ
CK2
10 pF
VSS
/CK2
SDRAMs (D0 to D7), SPD
Notes :
VCCID
Open
1. DQ wiring may differ from that described
in this drawing; however DQ/DM/DQS
relationships are maintained as shown.
VCCID strap connections:
(for memory device VCC, VCCQ)
Strap out (open): VCC = VCCQ
Strap in (closed): VCC ≠ VCCQ
2. The SDA pull-up registor is reguired due to
the open-drain/open-collector output.
3. The SCL pull-up registor is recommended,
because of the normal SCL lime inactive
"high" state.
Preliminary Data Sheet E0148H20 (Ver. 2.0)
9
HB54A2568KN-A75B/B75B/10B
Logical Clock Net Structure
4DRAM loads
DRAM1
DRAM2
120 Ω
DIMM
connector
DRAM3
DRAM4
Preliminary Data Sheet E0148H20 (Ver. 2.0)
10
HB54A2568KN-A75B/B75B/10B
Pin Functions (1)
CK (CLK), /CK (/CLK) (input pin): The CK and the /CK are the master clock inputs. All inputs except DMs, DQSs
and DQs are referred to the cross point of the CK rising edge and the VREF level. When a read operation, DQSs
and DQs are referred to the cross point of the CK and the /CK. When a write operation, DMs and DQs are referred
to the cross point of the DQS and the VREF level. DQSs for write operation are referred to the cross point of the CK
and the /CK.
/S (/CS) (input pin): When /S is Low, commands and data can be input. When /S is High, all inputs are ignored.
However, internal operations (bank active, burst operations, etc.) are held.
/RAS, /CAS, and /WE (input pins): These pins define operating commands (read, write, etc.) depending on the
combinations of their voltage levels. See "Command operation".
A0 to A12 (input pins): Row address (AX0 to AX12) is determined by the A0 to the A12 level at the cross point of
the CK rising edge and the VREF level in a bank active command cycle. Column address (AY0 to AY8) is loaded via
the A0 to the A8 at the cross point of the CK rising edge and the VREF level in a read or a write command cycle.
This column address becomes the starting address of a burst operation.
A10 (AP) (input pin): A10 defines the precharge mode when a precharge command, a read command or a write
command is issued. If A10 = High when a precharge command is issued, all banks are precharged. If A10 = Low
when a precharge command is issued, only the bank that is selected by BA1, BA0 is precharged. If A10 = High
when read or write command, auto-precharge function is enabled. While A10 = Low, auto-precharge function is
disabled.
BA0, BA1 (input pin): BA0/BA1 are bank select signals. The memory array is divided into bank 0, bank 1, bank 2
and bank 3. If BA1 = Low and BA0 = Low, bank 0 is selected. If BA1 = High and BA0 = Low, bank 1 is selected. If
BA1 = Low and BA0 = High, bank 2 is selected. If BA1 = High and BA0 = High, bank 3 is selected.
CKE (input pin): CKE controls power down and self-refresh. The power down and the self-refresh commands are
entered when the CKE is driven Low and exited when it resumes to High.
The CKE level must be kept for 1 CK cycle (= LCKEPW) at least, that is, if CKE changes at the cross point of the CK
rising edge and the VREF level with proper setup time tIS, at the next CK rising edge CKE level must be kept with
proper hold time tIH.
Pin Functions (2)
DQ (input and output pins): Data are input to and output from these pins.
DQS (input and output pin): DQS provide the read data strobes (as output) and the write data strobes (as input).
DM (input pins): DM is the reference signal of the data input mask function. DMs are sampled at the cross point of
DQS and VREF
VCC and VCCQ (power supply pins): 2.5V is applied. (VCC is for the internal circuit and VCCQ is for the output
buffer.)
VCCSPD (power supply pin): 2.5V is applied (For serial EEPROM).
VSS (power supply pin): Ground is connected.
Detailed Operation Part, AC Characteristics and Timing Waveforms
Refer to the HM5425161B/HM5425801B/HM5425401B Series datasheet (E0086H).
Preliminary Data Sheet E0148H20 (Ver. 2.0)
11
HB54A2568KN-A75B/B75B/10B
Electrical Specifications
Absolute Maximum Ratings
Parameter
Symbol
Value
Unit
Note
Voltage on any pin relative to VSS
VT
–1.0 to +4.6
V
1
Supply voltage relative to VSS
VCC, VCCQ
–1.0 to +4.6
V
1
Short circuit output current
IOUT
50
mA
Power dissipation
PT
8
W
Operating temperature
Topr
0 to +65
°C
Storage temperature
Tstg
–50 to +100
°C
Notes: 1. Respect to VSS.
DC Operating Conditions (TA = 0 to +65°C)
Parameter
Symbol
min.
Typ
max.
Unit
Notes
Supply voltage
VCC, VCCQ
2.3
2.5
2.7
V
1, 2
VSS
0
0
0
V
Input reference voltage
VREF
1.15
1.25
1.35
V
1
Termination voltage
VTT
VREF – 0.04
VREF
VREF + 0.04
V
1
DC Input high voltage
VIH
VREF + 0.18
—
VCCQ + 0.3
V
1, 3
DC Input low voltage
VIL
–0.3
—
VREF – 0.18
V
1, 4
DC Input signal voltage
VIN (dc)
–0.3
—
VCCQ + 0.3
V
5
DC differential input voltage
VSWING (dc) 0.36
—
VCCQ + 0.6
V
6
Notes: 1.
2.
3.
4.
5.
6.
All parameters are referred to VSS, when measured.
VCCQ must be lower than or equal to VCC.
VIH is allowed to exceed VCC up to 4.6V for the period shorter than or equal to 5ns.
VIL is allowed to outreach below VSS down to –1.0V for the period shorter than or equal to 5ns.
VIN (dc) specifies the allowable dc execution of each differential input.
VSWING (dc) specifies the input differential voltage required for switching.
Preliminary Data Sheet E0148H20 (Ver. 2.0)
12
HB54A2568KN-A75B/B75B/10B
DC Characteristics 1 (TA = 0 to 65°C, VCC, VCCQ = 2.5V ± 0.2V, VSS = 0V)
Parameter
Symbol
Operating current (ACTV-PRE)
ICC0
Operating current (ACTV-READ-PRE)
ICC1
Idle power down standby current
ICC2P
Idle standby current
ICC2N
Active power down standby current
ICC3P
Active standby current
ICC3N
Operating current
(Burst read operation)
ICC4R
Operating current
(Burst write operation)
ICC4W
Auto refresh current
ICC5
Self refresh current
ICC6
Notes. 1.
2.
3.
4.
5.
6.
7.
Grade
max.
-A75B
-B75B
-10B
-A75B
-B75B
-10B
-A75B
-B75B
-10B
-A75B
-B75B
-10B
-A75B
-B75B
-10B
-A75B
-B75B
-10B
-A75B
-B75B
-10B
-A75B
-B75B
-10B
-A75B
-B75B
-10B
600
560
480
820
760
680
144
120
96
320
280
240
200
160
120
400
360
320
1220
1160
1100
1160
1100
1040
1020
980
880
24
Unit
Test condition
Notes
mA
CKE ≥ VIH, tRC = min.
1, 2, 5
mA
CKE ≥ VIH, BL = 2,
CL = 2.5, tRC = min.
1, 2, 5
mA
CKE ≤ VIL
4
mA
CKE ≥ VIH, /CS ≥ VIH
4
mA
CKE ≤ VIL
3
mA
CKE ≥ VIH, /CS ≥ VIH
tRAS = max.
3
mA
CKE ≥ VIH, BL = 2,
CL = 2.5
1, 2, 5, 6
mA
CKE ≥ VIH, BL = 2,
CL = 2.5
1, 2, 5, 6
mA
tRFC = min.,
Input ≤ VIL or ≥ VIH
mA
Input ≥ VCC – 0.2V
Input ≤ 0.2V.
These ICC data are measured under condition that DQ pins are not connected.
One bank operation.
One bank active.
All banks idle.
Command/Address transition once per one cycle.
Data/Data mask transition twice per one cycle.
The ICC data on this table are measured with regard to tCK = min. in general.
DC Characteristics 2 (TA = 0 to 65°C, VCC, VCCQ = 2.5V ± 0.2V, VSS = 0V)
Parameter
Symbol
min.
max.
Unit
Test condition
Input leakage current
ILI
–10
10
µA
VCC ≥ VIN ≥ VSS
Output leakage current
ILO
–10
10
µA
VCC ≥ VOUT ≥ VSS
Output high voltage
VOH
VTT + 0.76
—
V
IOH (max.) = –15.2mA
Output low voltage
VOL
—
VTT – 0.76
V
IOL (min.) = 15.2mA
Preliminary Data Sheet E0148H20 (Ver. 2.0)
13
Notes
HB54A2568KN-A75B/B75B/10B
Pin Capacitance (TA = 25°C, VCC, VCCQ = 2.5V ± 0.2V)
[Parameter
Symbol
Pins
min.
max.
Unit
Notes
Input capacitance
CI1
Address, /RAS, /CAS,
/WE

60
pF
1
Input capacitance
CI2
CKE, /S CK, /CK

40
pF
1
Data and DQS input/output
capacitance
CO
DQ, DQS, DM

27
pF
1, 2
Notes: 1.These parameters are measured on conditions: f = 100MHz, VOUT = VCCQ/2, ∆VOUT = 0.2V.
2. Dout circuits are disabled.
Timing Parameter Measured in Clock Cycle for Unbuffered DIMM
Number of clock cycle
Parameter
Symbol
min.
Write to pre-charge command delay (same bank)
tWPD
3 + BL/2
Read to pre-charge command delay (same bank)
tRPD
BL/2
Write to read command delay (to input all data)
tWRD
2 + BL/2
Burst stop command to write command delay
(CL = 2)
tBSTW
2
(CL = 2.5)
tBSTW
3
Burst stop command to DQ High-Z
(CL = 2)
tBSTZ
2
(CL = 2.5)
tBSTZ
2.5
Read command to write command delay (to output all data)
(CL = 2)
tRWD
2 + BL/2
(CL = 2.5)
tRWD
3 + BL/2
Pre-charge command to High-Z
(CL = 2)
tHZP
2
(CL = 2.5)
tHZP
2.5
Write command to data in latency
tWCD
1
Write recovery
tWR
2
DM to data in latency
tDMD
0
Register set command to active or register set command
tMRD
2
Self refresh exit to non-read command
tSNR
10
Self refresh exit to read command
tSRD
200
Power down entry
tPDEN
1
Power down exit to command input
tPDEX
1
CKE minimum pulse width
tCKEPW
1
Preliminary Data Sheet E0148H20 (Ver. 2.0)
14
max.
HB54A2568KN-A75B/B75B/10B
Physical Outline
Unit: mm
67.60
63.60
11.55
18.45
3.80
(DATUM -A-)
4x Full R
4.00
199
1
6.00
20.0
31.75
Component area
(Front)
A
11.40
2.15
47.40
B
1.00 ± 0.10
2.45
4.20
4.20
1.50
11.40
2.45
2.15
47.40
2
200
R0.50 ± 0.20
R0.50 ± 0.20
2x φ 1.80
4.00 ± 0.10
Component area
(Back)
(DATUM -A-)
2.00 Min.
Detail A
Detail B
(DATUM -A-)
0.25 Max
2.55
4.00 ± 0.10
FULL R
0.60
0.45 ± 0.03
1.80
1.00 ± 0.10
ECA-TS2-0019-01
Preliminary Data Sheet E0148H20 (Ver. 2.0)
15
HB54A2568KN-A75B/B75B/10B
CAUTION FOR HANDLING MEMORY MODULES
When handling or inserting memory modules, be sure not to touch any components on the modules, such as
the memory ICs, chip capacitors and chip resistors. It is necessary to avoid undue mechanical stress on
these components to prevent damaging them.
In particular, do not push module cover or drop the modules in order to protect from mechanical defects,
which would be electrical defects.
When re-packing memory modules, be sure the modules are not touching each other.
Modules in contact with other modules may cause excessive mechanical stress, which may damage the
modules.
MDE0202
NOTES FOR CMOS DEVICES
1
PRECAUTION AGAINST ESD FOR MOS DEVICES
Exposing the MOS devices to a strong electric field can cause destruction of the gate
oxide and ultimately degrade the MOS devices operation. Steps must be taken to stop
generation of static electricity as much as possible, and quickly dissipate it, when once
it has occurred. Environmental control must be adequate. When it is dry, humidifier
should be used. It is recommended to avoid using insulators that easily build static
electricity. MOS devices must be stored and transported in an anti-static container,
static shielding bag or conductive material. All test and measurement tools including
work bench and floor should be grounded. The operator should be grounded using
wrist strap. MOS devices must not be touched with bare hands. Similar precautions
need to be taken for PW boards with semiconductor MOS devices on it.
2
HANDLING OF UNUSED INPUT PINS FOR CMOS DEVICES
No connection for CMOS devices input pins can be a cause of malfunction. If no
connection is provided to the input pins, it is possible that an internal input level may be
generated due to noise, etc., hence causing malfunction. CMOS devices behave
differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed
high or low by using a pull-up or pull-down circuitry. Each unused pin should be connected
to VDD or GND with a resistor, if it is considered to have a possibility of being an output
pin. The unused pins must be handled in accordance with the related specifications.
3
STATUS BEFORE INITIALIZATION OF MOS DEVICES
Power-on does not necessarily define initial status of MOS devices. Production process
of MOS does not define the initial operation status of the device. Immediately after the
power source is turned ON, the MOS devices with reset function have not yet been
initialized. Hence, power-on does not guarantee output pin levels, I/O settings or
contents of registers. MOS devices are not initialized until the reset signal is received.
Reset operation must be executed immediately after power-on for MOS devices having
reset function.
CME0107
Preliminary Data Sheet E0148H20 (Ver. 2.0)
16