EXAR XR-2209CP

XR-2209
...the analog plus
Voltage-Controlled
Oscillator
company TM
June 1997–3
FEATURES
APPLICATIONS
Excellent Temperature Stability (20ppm/°C)
Voltage and Current-to-Frequency Conversion
Linear Frequency Sweep
Stable Phase-Locked Loop
Wide Sweep Range (1000:1 Minimum)
Wide Supply Voltage Range (+4V to +13V)
Waveform Generation
Triangle, Sawtooth, Pulse, Squarewave
Low Supply Sensitivity (0.1% /V)
FM and Sweep Generation
Wide Frequency Range (0.01Hz to 1MHz)
Simultaneous Triangle and Squarewave Outputs
GENERAL DESCRIPTION
The XR-2209 is a monolithic voltage-controlled oscillator
(VCO) integrated circuit featuring excellent frequency
stability and a wide tuning range. The circuit provides
simultaneous triangle and squarewave outputs over a
frequency range of 0.01Hz to 1MHz. It is ideally suited for
FM, FSK, and sweep or tone generation, as well as for
phase-locked loop applications.
The oscillator of the XR-2209 has a typical drift
specification of 20ppm/°C. The oscillator frequency can
be linearly swept over a 1000:1 range with an external
control voltage.
ORDERING INFORMATION
Part No.
Package
Operating
Temperature Range
XR-2209CN
8 Lead 300 Mil CDIP
0° to +70°C
XR-2209M
8 Lead 300 Mil CDIP
-55°C to +125°C
XR-2209CP
8 Lead 300 Mil PDIP
0°C to +70°C
BLOCK DIAGRAM
Timing
Capacitor
C1
BIAS
1
5
A1
2
VCO
C2
Timing
Resistor
VCC
R
3
8
TWO
Triangle Wave Out
7
SWO
Square Wave Out
6
VEE
A2
4
Figure 1. XR-2209 Block Diagram
Rev. 2.02
1975
EXAR Corporation, 48720 Kato Road, Fremont, CA 94538 1
(510) 688-7000 FAX (510) 688-7017
XR-2209
PIN CONFIGURATION
VCC
1
8
C1
C2
TR
2
7
3
6
4
5
TWO
SWO
VEE
BIAS
8 Lead PDIP, CDIP (0.300”)
PIN DESCRIPTION
Pin #
Symbol
Type
Description
1
VCC
2
C1
I
Timing Capacitor Input.
3
C2
I
Timing Capacitor Input.
4
TR
I
Timing Resistor.
5
BIAS
I
Bias Input for Single Supply Operation.
6
VEE
7
SWO
O
Square Wave Output Signal.
8
TWO
O
Triangle Wave Output Signal.
Positive Power Supply.
Negative Power Supply.
Rev. 2.02
2
XR-2209
DC ELECTRICAL CHARACTERISTICS
Test Conditions: Test Circuit of Figure 3 and Figure 4, VCC = 12V, TA = +25°C, C = 5000pF, R = 20k, RL =
4.7k, S1 and S2 Closed Unless Otherwise Specified
XR-2209M
Parameters
Min.
Typ.
XR-2209C
Max.
Min.
26
13
8
4
Typ.
Max.
Units
Conditions
26
13
V
V
See Figure 3
Figure 4
General Characteristics
Supply Voltage
Single Supply
Split Supplies
8
4
Supply Current
Single Supply
5
7
5
8
mA
Split Supplies
Positive
Negative
5
4
7
6
5
4
8
7
mA
mA
Figure 3
Measured at Pin 1, S1, S2
Open
Figure 4
Measured at Pin 1, S1, S2
Open
Measured at Pin 4, S1, S2
Open
Oscillator Section - Frequency Characteristics
Upper Frequency Limit
0.5
1.0
0.5
1.0
MHz
C = 500pF, R = 2K
0.01
Hz
C = 50F, R = 2M
Lowest Practical Frequency
0.01
Frequency Accuracy
1
3
1
Frequency Stability
Temperature
Power Supply
20
0.15
50
30
0.15
ppm/°
C
%/V
1000:
1
fH/fL
1.5
5
%
%
fH = 10kHz, fL= 1kHz
fH = 100kHz, fL= 100Hz
0.1
%
+10% FM Deviation
k
See Characteristic Curves
75
Measured at Pin 4
6
10
+100
0.1
Vpp
mV
%
12
0.2
200
20
Vpp
V
nsec
nsec
Sweep Range
1000:
1
Sweep Linearity
10:1 Sweep
1000:1 Sweep
1
5
FM Distortion
Recommended Range of
Timing Resistor
3000:1
2
0.1
1.5
Impedance at Timing Pins
2000
1.5
75
5
% of fo
2000
0°C < TA < 70°C
R = 1.5 K for fH
R = 2M for fL
Output Characteristics
Triangle Output
Amplitude
Impedance
DC Level
Linearity
Squarewave Output
Amplitude
Saturation Voltage
Rise Time
Fall Time
Measured at Pin 8
4
6
10
+100
0.1
4
12
0.2
200
20
11
Referenced to Pin 6
From 10% to 90% of Swing
Measured at Pin 7, S2 Closed
11
0.4
0.4
Referenced to Pin 6
CL 10pF, RL = 4.7K
CL 10pF
Notes
Bold face parameters are covered by production test and guaranteed over operating temperature range.
Specifications are subject to change without notice
Rev. 2.02
3
XR-2209
ABSOLUTE MAXIMUM RATINGS
Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26V
Plastic package . . . . . . . . . . . . . . . . . . . . . . . . . 600mW
Derate above +25°C . . . . . . . . . . . . . . . . . . . 8mW/°C
SOIC package . . . . . . . . . . . . . . . . . . . . . . . . . . 300mW
Derate above +25°C . . . . . . . . . . . . . . . . . . . 4mW/°C
Storage Temperature Range . . . . . . . -65°C to +150°C
Power Dissipation (package limitation)
Ceramic package . . . . . . . . . . . . . . . . . . . . . . . 750mW
Derate above +25°C . . . . . . . . . . . . . . . . . . 10mW/°C
VCC
Q1
Q2
Q3
1
Q4
Q14
Q15
2R
Q13
R
Triangle Wave
Output
R
Q5
8
R
R
Timing
Capacitor
Q19
R1
2
Q6
Q7
2R
Q12
R3
3
Q9
Q8
R2
Q10
Q11
Á
R4
Timing Resistor
4
VEE
6
4R
Square Wave
Output
R5
R6
R7
7
Q20
Q21
Q27
Q22
5
BIAS
Q23
Figure 2. Equivalent Schematic Diagram
Rev. 2.02
4
Q24
Q25
Q26
XR-2209
PRECAUTIONS
SYSTEM DESCRIPTION
The following precautions should be observed when
operating the XR-2209 family of integrated circuits:
The XR-2209 functional blocks are shown in the block
diagram given in Figure 1. They are a voltage controlled
oscillator (VCO), and two buffer amplifiers for triangle and
squarewave outputs. Figure 2 is a simplified XR-2209
schematic diagram that shows the circuit in greater detail.
1.
2.
Pulling excessive current from the timing terminals
will adversely affect the temperature stability of the
circuit. To minimize this disturbance, it is
recommended that the total current drawn from pin 4
be limited to 6mA. In addition, permanent damage
to the device may occur if the total timing current
exceeds 10mA.
The VCO is a modified emitter-coupled current controlled
multivibrator. Its oscillation is inversely proportional to the
value of the timing capacitor connected to pins 2 and 3,
and directly proportional to the total timing current IT. This
current is determined by the resistor that is connected
from the timing terminals (pin 4) to ground.
Terminals 2, 3, and 4 have very low internal
impedance and should, therefore, be protected from
accidental shorting to ground or the supply voltage.
The triangle output buffer has a low impedance output
(10 typ.) while the squarewave is an open-collector
type. An external bias input allows the XR-2209 to be
used in either single or split supply applications.
VCC
VCC
S2
I+
C
RL
1F
1
2
VCC C1
3
C2
SWO
TWO
XR-2209
BIAS
7
Square Wave
Output
8
Triangle Wave
Output
5
VCC
5.1K
TR
VEE
6
4
5.1K
1F
IR
S1
Figure 3. Test Circuit for Single Supply Operation
Rev. 2.02
5
XR-2209
VCC
VCC
S2
C
I+
1F
RL
1
2
VCC C 1
3
C2
TR
4
R
Triangle Wave
Output
8
TWO
XR-2209
Square Wave
Output
7
SWO
5
BIAS
VEE
D1
6
10K
1F
VEE
I-
S1
1F
VEE
Figure 4. Test Circuit for Split Supply Operation
OPERATING CONSIDERATIONS
Bias for Single Supply (Pin 5)
Supply Voltage (Pins 1 and 6)
For single supply operation, pin 5 should be externally
biased to a potential between VCC/3 and VCC/2V (see
Figure 3.) The bias current at pin 5 is nominally 5% of the
total oscillation timing current, IT.
The XR-2209 is designed to operate over a power supply
range of $4V to $13V for split supplies, or 8V to 26V for
single supplies. Figure 5 shows the permissible supply
voltage for operation with unequal split supply voltages.
Figure 6 and Figure 7 show supply current versus supply
voltage. Performance is optimum for $6V split supply, or
12V single supply operation. At higher supply voltages,
the frequency sweep range is reduced.
Bypass Capacitors
The recommended value for bypass capacitors is 1F
although larger values are required for very low frequency
operation.
Timing Resistor (Pin 4)
The timing resistor determines the total timing current, IT,
available to charge the timing capacitor. Values for the
timing resistor can range from 2k to 2M; however, for
optimum temperature and power supply stability,
recommended values are 4k to 200k (see Figure 8,
Figure 9, Figure 10 and Figure 11.) To avoid parasitic
pick up, timing resistor leads should be kept as short as
possible.
Ground (Pin 6)
For split supply operation, this pin serves as circuit
ground. For single supply operation, pin 6 should be ac
grounded through a 1F bypass capacitor. During split
supply operation, a ground current of 2 IT flows out of this
terminal, where IT is the total timing current.
Rev. 2.02
6
XR-2209
Timing Capacitor (Pins 2 and 3)
The oscillator frequency is inversely proportional to the
timing capacitor, C. The minimum capacitance value is
limited by stray capacitances and the maximum value by
physical size and leakage current considerations.
Recommended values range from 100pF to 100F. The
capacitor should be non-polarized.
25
Positive Supply
20
15
Typical
Operating
Range
10
5
0
-5
-10
-15
-20
Negative Supply (V)
Figure 5. Operating Range for Unequal Split Supply Voltages
Positive Supply Current (mA)
35
30
25
20
15
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
RT=Parallel Combination
of Activated Timing
Resistors
TA=25°C
RT=2kΩ
RT=3kΩ
RT=5kΩ
RT=20kΩ
10
5
0
RT=200kΩ
RT=2MΩ
+4
8
+6
10 12 14
+8
+10
+12
+14
16 18 20 22 24 26 28
Single Supply Voltage (V)
Figure 6. Positive Supply Current, I+ (Measured at Pin 1) vs. Supply Voltage
Rev. 2.02
7
XR-2209
15
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
TA= 25°C
1MΩ
Total Timing Resistor RT
Negative Supply Current (mA)
TA= 25°C
10
5
0
0
±6
±8
±10
±12
100kΩ
Timing
Resistor
Range
10kΩ
1kΩ
0
0
Figure 7. Negative Supply Current,
I- (Measured at Pin 6)
vs. Supply Voltage
Frequency Error (%)
3
2
1
0
-1
-2
-3
-4
-5
-6
-7
8
+12V
+16V
16
24
Single Supply Voltage (V)
32
Figure 8. Recommended Timing Resistor
Value vs. Power Supply Voltage
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
VS = ±6V
C = 5000pF
1K
+8V
Split Supply Voltage (V)
±14
Split Supply Voltage (V)
7
6
5
4
+4V
10K
100K
1M
10M
Timing Resistance (Ω)
Figure 9. Frequency Accuracy vs. Timing
Resistance
Rev. 2.02
8
XR-2209
Normalized Frequency Drift
1.04
RT = 2MΩ
1.02
RT = 20kΩ
1.00
RT = 200kΩ
.98
.96
T A = 25°C
RT = Total
Timing
Resistance
C = 5000pF
.94
.92
±2
±4
4
RT = 2kΩ
±6
±8
±10
±12
Split Supply Voltage (V)
8
12
16
20
24
±14
28
Single Supply Voltage (V)
Figure 10. Frequency Drift vs. Supply Voltage
Normalized Frequency Drift (%)
+2
VS = ±6V
C = 5000pF
+1
4kΩ
200kΩ 2MΩ
2kΩ
0
20kΩ 4kΩ
20kΩ
-1
200kΩ
R = 2kΩ
-2
2MΩ
-3
-50
-25
0
+25 +50 +75 +100 +125
Temperature (°C)
Figure 11. Normalized Frequency Drift with Temperature
Squarewave Output (Pin 7)
Triangle Output (Pin 8)
The squarewave output at pin 7 is an “open-collector”
stage capable of sinking up to 20mA of load current. RL
serves as a pull-up load resistor for this output.
Recommended values for RL range from 1k to 100k.
The output at pin 8 is a triangle wave with a peak swing of
approximately one-half of the total supply voltage. Pin 8
has a 10 output impedance and is internally protected
against short circuits.
Rev. 2.02
9
XR-2209
MODES OF OPERATION
Split Supply Operation
Figure 12 is the recommended configuration for split
supply operation. Diode D1 in the figure assures that the
triangle output swing at pin 8 is symmetrical about
ground. The circuit operates with supply voltages ranging
from $4V to $13V. Minimum drift occurs with $6V
supplies. For operation with unequal supply voltages, see
Figure 5.
operation is determined by the timing capacitor, C, and
the timing resistor.
The squarewave output is obtained at pin 7 and has a
peak-to-peak voltage swing equal to the supply voltages.
This output is an “open-collector” type and requires an
external pull-up load resistor (nominally 5k) to the
positive supply. The triangle waveform obtained at pin 8 is
centered about ground and has a peak amplitude of
VCC/2.
With the generalized circuit of Figure 12, the frequency of
VCC
VCC
C
1F
RL
1
2
VCC C1
XR-2209
Square Wave
Output
3
C2
SWO
TWO
BIAS
TR
VEE
4
6
7
Triangle Wave
Output
8
5
D1
10K
1F
VEE
R
1F
VEE
Figure 12. Split-Supply Operation, Recommended Configuration
Rev. 2.02
10
XR-2209
Figure 13 is a simplified configuration for operation with
split supplies in excess of +7V. This circuit eliminates the
diode D1 used in Figure 12 by grounding pin 5 directly;
however, the triangle wave output now has a +0.6V DC
offset with respect to ground.
VCC
VCC
C
1F
RL
1
2
VCC C1
3
C 2 SWO 7
8
TWO
XR-2209
5
BIAS
TR
VEE
4
6
Square Wave
Output
Triangle Wave
Output
VEE
R
1F
VEE
Figure 13. Split-Supply Operation, Simplified Configuration
Rev. 2.02
11
XR-2209
VCC
VCC
C
1F
RL
Square Wave
Output
1
2
VCC C1
3
C 2 SWO 7
8
TWO
XR-2209
5
BIAS
Triangle Wave
Output
5.1K
TR
VEE
4
6
5.1K
VCC
1F
R
Figure 14. Single Supply Operation
Single Supply Operation
Frequency Control (Sweep and FM) - Split Supply
The circuit should be interconnected as shown in
Figure 14 for single supply operation. Pin 6 should be
grounded, and pin 5 biased from VCC through a resistive
divider to a value of bias voltage between VCC/3 and
VCC/2.
The circuit given in Figure 15 shows a frequency sweep
method for split supply operation.
The frequency of operation is controlled by varying the
total timing current, IT, drawn from the activated timing pin
4. The timing current can be modulated by applying a
control voltage, VC, to the timing pin through a series
resistor R. As the control voltage becomes more
negative, both the total timing current, IT, and the
oscillation frequency increase.
The frequency of operation is determined by the timing
capacitor C and the timing resistor R, and is equal to
1/RC. The squarewave output is obtained at pin 7 and
has a peak-to-peak voltage swing equal to the supply
voltage. This output is an “open-collector” type and
requires an external pull-up load resistor (nominally 5k)
to V+. The triangle waveform obtained at pin 8 is centered
about a voltage level VO where:
The frequency of operation, is now proportional to the
control voltage, VC, and determined as:
f + 1
RC
VO + VB ) 0.6V
where VB is the bias voltage at pin 5. The peak-to-peak
output swing of triangle wave is approximately equal to
VCC/2.
Rev. 2.02
12
ƪ1 ) RV VR ƫ Hz
C
C
EE
XR-2209
frequency is given as:
If R = 2M, RC = 2k, C = 5000pF, then a 1000:1
frequency sweep would result for a negative sweep
voltage VC VEE.
f + 1
RC
The voltage to frequency conversion gain, K, is controlled
by the series resistance RC and can be expressed as:
1
K + f + HzńV
V C
RCCVEE
ƪ
ǒ
V
1) R 1 – C
RC
VT
Ǔƫ
where VT = Vpin4 ~ Vbias + 0.7V.
This equation is valid from VC = 0V where RC is in parallel
with R and IT is maximum to:
The circuit of Figure 15 can operate both with positive
and negative values of control voltage. However, for
positive values of VC with small (RC/R) ratio, the direction
of the timing current IT is reversed and the oscillations will
stop.
VC + VT
ǒ1 ) RR Ǔ
C
Frequency Control (Sweep and FM) - Single Supply
where IT = 0 and oscillation ceases.
The circuit given in Figure 16 shows the frequency sweep
method for single supply operation. Here, the oscillation
Caution: Total timing current IT must be less than 6mA over the
frequency control range.
VCC
VCC
C
1F
RL
1
2
VCC TC1
3
TC2
XR-2209
SWO
TWO
BIAS
7
8
5
Square Wave
Output
Triangle Wave
Output
VEE
6
T4
4
IT
VEE
IO
IC
1F
RC
R
VC
VEE
VC+
VC-
Sweep
or
FM
Voltage
Figure 15. Frequency Sweep Operation, Split Supply
Rev. 2.02
13
XR-2209
VCC
VCC
C
1F
RL
1
2
VEE C 1
3
C 2 SWO
XR-2209
TWO
BIAS
T4
8
Vbias
5
Triangle Wave
Output
5.1K
VEE
4
R
Square Wave
Output
7
1F
6
3.9K
RC
VC
VC+
VC-
Sweep
or
FM
Voltage
Figure 16. Frequency Sweep Operation, Single Supply
Rev. 2.02
14
VCC
XR-2209
8 LEAD PLASTIC DUAL-IN-LINE
(300 MIL PDIP)
Rev. 1.00
8
5
1
4
E1
E
D
A2
A
Seating
Plane
L
α
A1
B
e
INCHES
SYMBOL
eA
eB
B1
MILLIMETERS
MIN
MAX
MIN
MAX
A
0.145
0.210
3.68
5.33
A1
0.015
0.070
0.38
1.78
A2
0.015
0.195
2.92
4.95
B
0.014
0.024
0.36
0.56
B1
0.030
0.070
0.76
1.78
C
0.008
0.014
0.20
0.38
D
0.348
0.430
8.84
10.92
E
0.300
0.325
7.62
8.26
E1
0.240
0.280
6.10
7.11
e
0.100 BSC
2.54 BSC
eA
0.300 BSC
7.62 BSC
eB
0.310
0.430
7.87
10.92
L
0.115
0.160
2.92
4.06
α
0°
15°
0°
15°
Note: The control dimension is the inch column
Rev. 2.02
15
C
XR-2209
8 LEAD CERAMIC DUAL-IN-LINE
(300 MIL CDIP)
Rev. 1.00
8
5
1
4
E
E1
D
A1
Base
Plane
A
Seating
Plane
L
c
e
B
INCHES
SYMBOL
α
B1
MILLIMETERS
MIN
MAX
MIN
A
0.100
0.200
2.54
5.08
A1
0.015
0.060
0.38
1.52
B
0.014
0.026
0.36
0.66
B1
0.045
0.065
1.14
1.65
c
0.008
0.018
0.20
0.46
D
0.305
0.405
7.75
10.29
E1
0.250
0.310
6.35
7.87
E
e
L
0.300 BSC
0.100 BSC
0.125
0.200
MAX
7.62 BSC
2.54 BSC
3.18
5.08
α
0°
15°
0°
Note: The control dimension is the inch column
15°
Rev. 2.02
16
XR-2209
Notes
Rev. 2.02
17
XR-2209
Notes
Rev. 2.02
18
XR-2209
Notes
Rev. 2.02
19
XR-2209
NOTICE
EXAR Corporation reserves the right to make changes to the products contained in this publication in order to improve design, performance or reliability. EXAR Corporation assumes no responsibility for the use of any circuits described herein, conveys no license under any patent or other right, and makes no representation that the circuits are
free of patent infringement. Charts and schedules contained herein are only for illustration purposes and may vary
depending upon a user’s specific application. While the information in this publication has been carefully checked;
no responsibility, however, is assumed for inaccuracies.
EXAR Corporation does not recommend the use of any of its products in life support applications where the failure or
malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly
affect its safety or effectiveness. Products are not authorized for use in such applications unless EXAR Corporation
receives, in writing, assurances to its satisfaction that: (a) the risk of injury or damage has been minimized; (b) the
user assumes all such risks; (c) potential liability of EXAR Corporation is adequately protected under the circumstances.
Copyright 1975 EXAR Corporation
Datasheet June1997
Reproduction, in part or whole, without the prior written consent of EXAR Corporation is prohibited.
Rev. 2.02
20