FUJITSU MB91FV130CR-ES

FUJITSU SEMICONDUCTOR
DATA SHEET
DS07-16308-1E
32-Bit RISC Microcontroller
CMOS
FR30 Series
MB91133/MB91F133
■ DESCRIPTION
The MB91133/MB91F133, a standard single-chip microcontroller featuring various I/O resources and bus control
mechanisms to incorporate the control required for high-performance high-speed CPU processes, is the core unit
in the 32-bit RISC CPU (FR family) .
This unit has the optimal specifications for incorporating applications that require high-performance CPU processing power by featuring peripheral I/O resources suitable for single-lens reflex cameras, digital video cameras,
etc.
■ FEATURES
1. CPU
•
•
•
•
•
•
•
•
•
•
•
32-bit RISC (FR30) , load/store architecture, 5-level pipeline
Multi-purpose register : 32 bits × 16
16-bit fixed length instructions (basic instructions) , 1 instruction per cycle
Instructions for barrel shift, bit processing and inter-memory transfers : Instructions suited to loading purposes
Function entry / exit instruction, multi load / store instruction of register details : High-level language handling
instruction
Register interlock function : Simplification of assembler description
Branch instruction with delay slot : Reduction in overheads in case of branching
Multiplier is built-in / supported at instruction level.
Signed 32-bit multiplication : 5 cycles
Signed 16-bit multiplication : 3 cycles
Interruption (saving PC and PS) : 6 cycles, 16 priority levels
(Continued)
■ PACKAGES
144-pin plastic FBGA
144-pin plastic LQFP
(BGA-144P-M01)
(FPT-144P-M08)
MB91133/MB91F133
(Continued)
2. Bus Interface
•
•
•
•
•
24-bit address output, 8/16-bit data input/output
Basic bus cycle : 2 clock cycles
Interface support for various memories
Unused data and address pins can be used as input/output ports.
Supports “little endian” mode
3. Built-in ROM
Mask device : 254 KB; FLASH device : 254 KB; EVA-FLASH device : 254 KB
4. Built-in RAM
Mask device : 8 KB; FLASH device : 8 KB; EVA-FLASH device : 8 KB
5. DMA Controller
This is a descriptor-type MA controller whose transfer parameters are arranged in the main memory.
A maximum of 8 factors in total (internal and external) can be transferred.
External factors are 3 channels.
6. Bit Search Module
Searches the first “1” / “0” change bit positions within 1 cycle from MSB in 1 word
7. Timer
• 16-bit reload timer × 5 channels
• 16-bit OCU × 8 channels, ICU × 4 channels, free-run timer × 1 channel
Output waveform adjusting function for AC motor waveforms is included in the above timer.
• 8/16-bit up/down timer/counter (8-bit × 2 channels or 16-bit × 1 channel)
External interruption and pin are shared for AIN and BIN.
• 16-bit down count timer × 5 channels; can also be used as the UART baud rate timer
• 16-bit PPG timer × 6 channels; out-pulse cycle / duty can be changed at random
8. D/A Converter
• 8-bit × 3 channels
9. A/D Converter (Sequential comparison type)
•
•
•
•
10-bit × 8 channels
Sequential conversion method (conversion time 5.0 µs at 33 MHz)
Setting for single conversion, scan conversion and repeat conversion is possible.
Conversion starting function using hardware or software
10. Serial I/O
• UART × 5 channels; clock synchronous serial transfer with LSB / MSB switching function is possible for both.
• Serial data output or serial lock output can be selected using push-pull / open-drain software.
11. Level Comparator Input
• 1 channel; shared input and pins of A/D converter.
12. Clock Switching Function
• Base clock : Software can be used to select from two types of clock sources, namely 32 kHz and high-speed.
• Gear function : Four types of settings (1 : 1, 1 : 2, 1 : 4, 1 : 8) can be set individually as the operating clock
ratio to the basic clock per CPU and peripheral equipment.
2
MB91133/MB91F133
13. Interruption Controller
• External interruption input (total 24 channels)
• With pull up pin control / standby return function : 4 channels
(rising / falling / H level / L level settings are possible)
• With pull up pin control / standby return function; AIN / BIN pins of the up/down counter are shared : 4 channels
(rising / falling / H level / L level settings are possible)
• With pull up pin controln : 16 channels
(rising / falling / H level / L level settings are possible)
• Internal interruption factor
• Interruption / delay interruption by resource
14. Others
• Reset factors
Power on reset, watchdog timer, software reset, external reset
• Low power consumption mode
Sleep/stop mode
• Packages
FBGA-144, LQFP-144
• CMOS technology (0.35 µm)
• Power
Two power sources (5 V / 3 V)
1) 5 V system : 5 V ± 10% (A/D, D/A and level comparator included)
2) 3 V system : A) 3.0 V to 3.6 V : All functions guaranteed
B) 2.7 V to 3.0 V : All functions guaranteed for single-chip mode of mask devices only
■ PRODUCT LINEUP
MB91133
MB91F133
MB91FV130
MASK ROM device
(mass production item)
FLASH ROM device
(for evaluation)
Piggy/EVA device
(for evaluation /
development)
6 KB
6 KB
6 KB
CROM capacity
254 KB


FLASH capacity

254 KB
254 KB
CRAM capacity
2 KB
2 KB
2 KB
Mass production
Trial production
Provided
CLASSIFICATION
RAM capacity
Others
3
MB91133/MB91F133
■ PIN ASSIGNMENTS
• MB91FV130
(BOTTOM VIEW)
3
299 296 293 277 274 270 268 278 275 262 254 247 257 252 250 245 233 230 224
2
298 292 289 286 283 280 276 269 264 263 258 251 248 243 240 237 234 225 221
5
10
4
297 291 287 284 279 271 265 261 256 249 242 239 235 229 228 219 218
8
13
6
300 295 290 285 281 272 267 259 255 246 241 236 231 226 223 215 207
25
16
11
7
1
294 288 282 273 266 260 253 244 238 232 227 222 217 212 202
27
19
15
12
9
220 216 213 209 199
32
23
18
17
14
214 211 210 205 195
34
26
24
21
20
208 206 204 201 203
22
33
31
30
28
198 197 196 194 200
29
39
38
35
36
192 193 191 190 187
37
40
41
43
42
186 185 188 189 179
50
44
46
47
48
178 180 181 183 172
53
51
54
56
58
170 171 174 176 184
45
55
60
61
64
164 167 168 173 182
49
59
63
66
70
159 162 165 169 177
52
62
67
72
77
82
88
94
103 110 116 123 133 139 145 153 157 161 166 175
57
65
73
76
81
86
91
96
105 109 117 122 131 136 141 147 151 156 163 158
68
69
78
79
85
89
92
99
106 111 115 121 129 135 138 142 148 154 160 155
71
75
84
87
90
93
98
101 108 113 114 119 126 130 134 137 140 144 150 152
74
80
83
95
100 102 107
97
104 112 125 128 118 120 124 127 132 143 146 149
(PGA-299C-A01)
4
MB91133/MB91F133
• MB91F133/MB91133
(TOP VIEW)
14
108
107
106
102
99
96
92
89
85
82
79
75
74
72
13
110
109
105
103
100
97
93
88
84
81
78
76
73
71
12
111
112
113
104
101
98
91
90
86
83
80
77
69
70
11
115
114
116
95
94
87
68
67
66
10
118
117
119
65
64
63
9
121
120
122
59
62
61
60
8
125
124
126
123
58
55
57
56
7
128
129
127
130
51
54
52
53
6
132
133
134
131
50
48
49
5
135
136
137
47
45
46
4
138
139
140
44
42
43
3
142
141
5
8
11
2
143
1
4
6
1
144
2
3
A
B
C
15
22
23
14
18
19
26
29
32
41
40
39
9
12
16
21
25
28
31
33
37
38
7
10
13
17
20
24
27
30
34
35
36
D
E
F
G
H
J
K
L
M
N
P
INDEX
(BGA-144P-M01)
5
P61/A17/INT17
P62/A18/INT18
P63/A19/INT19
P64/A20/INT20
P65/A21/INT21
P66/A22/INT22
P67/A23/INT23
VCC3
P80/RDY
P81/BGRNT
P82/BRQ
P83/RD
P84/WR0
P85/WR1
P86/CLK
VSS
PC0/INT0
PC1/INT1
PC2/INT2
PC3/INT3
PC4/AIN0/INT4
PC5/BIN0/INT5
PC6/AIN1/INT6
PC7/BIN1/INT7
PD0/INT8/TRG0
PD1/INT9/TRG1
PD2/INT10/TRG2
PD3/INT11/TRG3
PD4/INT12/TRG4
PD5/INT13/TRG5
PD6/DEOP2/INT14
PD7/ATG/INT15
PE0/ZIN0
PE1/ZIN1
PE2/IN0
PE3/IN1
P20/D16
P21/D17
P22/D18
P23/D19
P24/D20
P25/D21
P26/D22
P27/D23
VSS
P30/D24
P31/D25
P32/D26
P33/D27
P34/D28
P35/D29
P36/D30
P37/D31
P40/A00
P41/A01
P42/A02
P43/A03
P44/A04
P45/A05
P46/A06
P47/A07
VSS
VCC5
P50/A08
P51/A09
P52/A10
P53/A11
P54/A12
P55/A13
P56/A14
P57/A15
P60/A16/INT16
6
144
143
142
141
140
139
138
137
136
135
134
133
132
131
130
129
128
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
MD2
MD1
MD0
VSS
X1
X0
VCC3
X1A
X0A
VSS
RST
PL7/DACK2
PL6/DREQ2
PL5/DEOP1
PL4/DACK1
PL3/DREQ1
PL2/DEOP0
PL1/DACK0
PL0/DREQ0
PK7/AN7/CMP
PK6/AN6
PK5/AN5
PK4/AN4
PK3/AN3
PK2/AN2
PK1/AN1
PK0/AN0
AVSS
AVRL
AVRH
AVCC
DAVC
DAVS
DA0
DA1
DA2
MB91133/MB91F133
• MB91F133/MB91133
(TOP VIEW)
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
(FPT-144P-M08)
VCC5
PH0/SIN0
PH1/SOT0
PH2/SCK0
PI0/SIN1
PI1/SOT1
PI2/SCK1
PI3/SIN2
PI4/SOT2
PI5/SCK2
PJ0/SIN3
PJ1/SOT3
PJ2/SCK3
PJ3/SIN4
PJ4/SOT4
PJ5/SCK4
VCC3
VSS
PG5/PPG5
PG4/PPG4
PG3/PPG3
PG2/PPG2
PG1/PPG1
PG0/PPG0
PF7/RTO7
PF6/RTO6
PF5/RTO5
PF4/RTO4
PF3/RTO3
PF2/RTO2
PF1/RTO1
PF0/RTO0
PE7/DTTI
PE6/FRCK
PE5/IN3
PE4/IN2
MB91133/MB91F133
■ PIN NUMBERS LIST
• Device : MB91FV130 Package : PGA-299C-A01
No.
Pin Name
No.
Pin Name
No.
Pin Name
No.
Pin Name
1
P20/D16
35
P54/A12
69
N.C.
103
PK3/AN3
2
VSS
36
P55/A13
70
N.C.
104
VCC5
3
OPEN
37
VCC5
71
VSS
105
PK4/AN4
4
P21/D17
38
P56/A14
72
N.C.
106
PK5/AN5
5
VCC5
39
P57/A15
73
N.C.
107
PK6/AN6
6
P22/D18
40
P60/A16/INT16
74
VCC5
108
PK7/AN7/CMP
7
P23/D19
41
P61/A17/INT17
75
N.C.
109
DAVC
8
VSS
42
P62/A18/INT18
76
MD0
110
DAVS
9
P24/D20
43
P63/A19/INT19
77
MD1
111
DA0
10
P25/D21
44
P64/A20/INT20
78
MD2
112
VSS
11
P26/D22
45
P65/A21/INT21
79
VCC3
113
DA1
12
P27/D23
46
P66/A22/INT22
80
VSS
114
DA2
13
P30/D24
47
P67/A23/INT23
81
X0
115
PH0/SIN0
14
P31/D25
48
P80/RDY
82
X1
116
PH1/SOT0
15
P32/D26
49
VCC3
83
VCC5
117
PH2/SCK0
16
P33/D27
50
VSS
84
RST
118
PI0/SIN1
17
P34/D28
51
P81/BGRNT
85
N.C.
119
PI1/SOT1
18
P35/D29
52
P82/BRQ
86
ICLK
120
PI2/SCK1
19
P36/D30
53
VCC5
87
ICS0
121
PI3/SIN2
20
P37/D31
54
P83/RD
88
ICS1
122
PI4/SOT2
21
P40/A00
55
P84/WR0
89
ICS2
123
PI5/SCK2
22
VCC5
56
P85/WR1
90
ICD0
124
PJ0/SIN3
23
P41/A01
57
P86/CLK
91
ICD1
125
VCC5
24
P42/A02
58
PL0/DREQ0
92
ICD2
126
PJ1/SOT3
25
P43/A03
59
PL1/DACK0
93
ICD3
127
PJ2/SCK3
26
P44/A04
60
PL2/DEOP0
94
BREAK
128
VSS
27
P45/A05
61
PL3/DREQ1
95
AVCC
129
VCC3
28
P46/A06
62
PL4/DACK1
96
AVRH
130
X0A
29
VSS
63
PL5/DEOP1
97
VSS
131
X1A
30
P47/A07
64
PL6/DREQ2
98
AVRL
132
VSS
31
P50/A08
65
PL7/DACK2
99
AVSS
133
PJ3/SIN4
32
P51/A09
66
N.C.
100
PK0/AN0
134
PJ4/SOT4
33
P52/A10
67
N.C.
101
PK1/AN1
135
PJ5/SCK4
34
P53/A11
68
VCC5
102
PK2/AN2
136
PC0/INT0
(Continued)
7
MB91133/MB91F133
(Continued)
No.
Pin Name
8
No.
Pin Name
No.
Pin Name
No.
Pin Name
No.
Pin Name
137
PC1/INT1
173
PF5/RTO5
209
TAD14
245
TDT23
281
TDT53
138
PC2/INT2
174
PF6/RTO6
210
TAD15
246
TDT24
282
TDT54
139
PC3/INT3
175
PF7/RTO7
211
VCC3
247
VSS
283
TDT55
140
PC4/INT4/AIN0
176
PG0/PPG0
212
TOE
248
TDT25
284
TDT56
141
PC5/INT5/BIN0
177
PG1/PPG1
213
TCE1
249
TDT26
285
TDT57
142
PC6/INT6/AIN1
178
PG2/PPG2
214
TADSC
250
TDT27
286
VCC3
143
VCC5
179
VSS
215
TWR
251
TDT28
287
TDT58
144
PC7/INT7/BIN1
180
PG3/PPG3
216
TDT00
252
TDT29
288
TDT59
145
PD0/INT8/TRG0
181
PG4/PPG4
217
TDT01
253
TDT30
289
TDT60
146
VSS
182
PG5/PPG5
218
VSS
254
VCC5
290
TDT61
147
PD1/INT9/TRG1
183
N.C.
219
TDT02
255
TDT31
291
TDT62
148
PD2/INT10/TRG2
184
N.C.
220
TDT03
256
TDT32
292
TDT63
149
VCC5
185
N.C.
221
VCC5
257
TDT33
293
VCC5
150
PD3/INT11/TRG3
186
N.C.
222
TDT04
258
TDT34
294
TDT64
151
PD4/INT12/TRG4
187
VCC5
223
TDT05
259
TDT35
295
TDT65
152
VSS
188
EXRAM
224
VSS
260
TDT36
296
VSS
153
PD5/INT13/TRG5
189
TAD00
225
TDT06
261
TDT37
297
TDT66
154
PD6/INT14/DEOP2
190
TAD01
226
TDT07
262
VSS
298
TDT67
155
VCC5
191
TAD02
227
TDT08
263
TDT38
299
VCC5
156
PD7/INT15/ATG
192
TAD03
228
TDT09
264
TDT39
300
TDT68
157
PE0/ZIN0
193
VCC3
229
TDT10
265
TDT40
158
VSS
194
TAD04
230
VCC5
266
TDT41
159
PE1/ZIN1
195
TAD05
231
TDT11
267
TDT42
160
PE2/IN0
196
TAD06
232
TDT12
268
TDT43
161
PE3/IN1
197
TAD07
233
VSS
269
VCC3
162
PE4/IN2
198
TAD08
234
TDT13
270
TDT44
163
PE5/IN3
199
TAD09
235
TDT14
271
TDT45
164
PE6/FRCK
200
VSS
236
TDT15
272
TDT46
165
PE7/DTTI
201
TAD10
237
TDT16
273
TDT47
166
VCC3
202
TAD11
238
TDT17
274
TDT48
167
PF0/RTO0
203
VCC5
239
TDT18
275
VCC5
168
PF1/RTO1
204
TAD12
240
VCC3
276
TDT49
169
PF2/RTO2
205
TAD13
241
TDT19
277
TDT50
170
PF3/RTO3
206
TAD14
242
TDT20
278
VSS
171
PF4/RTO4
207
TAD15
243
TDT21
279
TDT51
172
VCC5
208
TCLK
244
TDT22
280
TDT52
MB91133/MB91F133
• Device : MB91F133/MB91133
LQFP FBGA
Pin Name
Package : BGA-144P-M01/FPT-144P-M08
LQFP FBGA
Pin Name
LQFP FBGA
Pin Name
1
B2
P20/D16
36
P1
P60/A16/INT16
71
P13
PE2/IN0
2
B1
P21/D17
37
N2
P61/A17/INT17
72
P14
PE3/IN1
3
C1
P22/D18
38
P2
P62/A18/INT18
73
N13
PE4/IN2
4
C2
P23/D19
39
P3
P63/A19/INT19
74
N14
PE5/IN3
5
C3
P24/D20
40
N3
P64/A20/INT20
75
M14
PE6/FRCK
6
D2
P25/D21
41
M3
P65/A21/INT21
76
M13
PE7/DTTI
7
D1
P26/D22
42
N4
P66/A22/INT22
77
M12
PF0/RTO0
8
D3
P27/D23
43
P4
P67/A23/INT23
78
L13
PF1/RTO1
9
E2
VSS
44
M4
VCC3
79
L14
PF2/RTO2
10
E1
P30/D24
45
N5
P80/RDY
80
L12
PF3/RTO3
11
E3
P31/D25
46
P5
P81/BGRNT
81
K13
PF4/RTO4
12
F2
P32/D26
47
M5
P82/BRQ
82
K14
PF5/RTO5
13
F1
P33/D27
48
N6
P83/RD
83
K12
PF6/RTO6
14
F3
P34/D28
49
P6
P84/WR0
84
J13
PF7/RTO7
15
G4
P35/D29
50
M6
P85/WR1
85
J14
PG0/PPG0
16
G2
P36/D30
51
L7
P86/CLK
86
J12
PG1/PPG1
17
G1
P37/D31
52
N7
VSS
87
H11
PG2/PPG2
18
G3
P40/A00
53
P7
PC0/INT0
88
H13
PG3/PPG3
19
H3
P41/A01
54
M7
PC1/INT1
89
H14
PG4/PPG4
20
H1
P42/A02
55
M8
PC2/INT2
90
H12
PG5/PPG5
21
H2
P43/A03
56
P8
PC3/INT3
91
G12
VSS
22
H4
P44/A04
57
N8
PC4/AIN0/INT4
92
G14
VCC3
23
J4
P45/A05
58
L8
PC5/BIN0/INT5
93
G13
PJ5/SCK4
24
J1
P46/A06
59
L9
PC6/AIN1/INT6
94
G11
PJ4/SOT4
25
J2
P47/A07
60
P9
PC7/BIN1/INT7
95
F11
PJ3/SIN4
26
J3
VSS
61
N9
PD0/INT8/TRG0
96
F14
PJ2/SCK3
27
K1
VCC5
62
M9
PD1/INT9/TRG1
97
F13
PJ1/SOT3
28
K2
P50/A08
63
P10
PD2/INT10/TRG2
98
F12
PJ0/SIN3
29
K3
P51/A09
64
N10
PD3/INT11/TRG3
99
E14
PI5/SCK2
30
L1
P52/A10
65
M10
PD4/INT12/TRG4
100
E13
PI4/SOT2
31
L2
P53/A11
66
P11
PD5/INT13/TRG5
101
E12
PI3/SIN2
32
L3
P54/A12
67
N11
PD6/DEOP2/INT14
102
D14
PI2/SCK1
33
M2
P55/A13
68
M11
PD7/ATG/INT15
103
D13
PI1/SOT1
34
M1
P56/A14
69
N12
PE0/ZIN0
104
D12
PI0/SIN1
35
N1
P57/A15
70
P12
PE1/ZIN1
105
C13
PH2/SCK0
(Continued)
9
MB91133/MB91F133
(Continued)
LQFP FBGA
10
Pin Name
LQFP FBGA
Pin Name
106
C14
PH1/SOT0
126
C8
PL0/DREQ0
107
B14
PH0/SIN0
127
C7
PL1/DACK0
108
A14
VCC5
128
A7
PL2/DEOP0
109
B13
DA2
129
B7
PL3/DREQ1
110
A13
DA1
130
D7
PL4/DACK1
111
B12
DA0
131
D6
PL5/DEOP1
112
A12
DAVS
132
A6
PL6/DREQ2
113
C12
DAVC
133
B6
PL7/DACK2
114
B11
AVCC
134
C6
RST
115
A11
AVRH
135
A5
VSS
116
C11
AVRL
136
B5
X0A
117
B10
AVSS
137
C5
X1A
118
A10
PK0/AN0
138
A4
VCC3
119
C10
PK1/AN1
139
B4
X0
120
B9
PK2/AN2
140
C4
X1
121
A9
PK3/AN3
141
B3
VSS
122
C9
PK4/AN4
142
A3
MD0
123
D8
PK5/AN5
143
A2
MD1
124
B8
PK6/AN6
144
A1
MD2
125
A8
PK7/AN7/CMP
MB91133/MB91F133
■ PIN DESCRIPTIONS
Pin No.
Pin name
Circuit
type
Function
1
2
3
4
5
6
7
8
D16/P20
D17/P21
D18/P22
D19/P23
D20/P24
D21/P25
D22/P26
D23/P27
C
External data bus bits 16 to 23
Only valid for external bus 16-bit mode. Can be used as ports in
single-chip and external bus 8-bit modes.
10
11
12
13
14
15
16
17
D24/P30
D25/P31
D26/P32
D27/P33
D28P34
D29/P35
D30/P36
D31/P37
C
External data bus bits 24 to 31
Can be used as ports in single-chip mode.
18
19
20
21
22
23
24
25
28
29
30
31
32
33
34
35
A00/P40
A01/P41
A02/P42
A03/P43
A04/P44
A05/P45
A06/P46
A07/P47
A08/P50
A09/P51
A10/P52
A11/P53
A12/P54
A13/P55
A14/P56
A15/P57
F
External address bus bits 0 to 15
Valid for external bus mode. Can be used as ports in single-chip
mode.
36
37
38
39
40
41
42
43
A16/INT16/P60
A17/INT17/P61
A18/INT18/P62
A19/INT19/P63
A20/INT20/P64
A21/INT21/P65
A22/INT22/P66
A23/INT23/P67
O
External address bus bits 16 to 23
[ INT16 to 23 ] are external interruption request inputs 16 to 23.
These inputs are always used when dealing with external interruptions is permitted, so output by ports should be stopped except
when carried out intentionally.
Can be used as ports when address bus and external interruption
request input are not used.
C
External RDY input
This function is valid when external RDY input is permitted. “0” is
input if the bus cycle being executed is not completed.
Can be used as a port when the external RDY input is not used.
45
RDY/P80
(Continued)
11
MB91133/MB91F133
Pin No.
46
47
Pin name
BGRNT/P81
BRQ/P82
Circuit
type
Function
F
External bus open reception output
This function is valid when external bus open reception output is
permitted. “L” is output if the external bus is opened. Can be used
as a port when the external bus open reception output is prohibited.
C
External bus open request input
This function is valid when external bus open request input is permitted. “1” is input if the external bus requests to be opened.
Can be used as a port when the external bus open request input is
not used.
48
RD/P83
F
External bus read strobe output
This function is valid when external bus read strobe output is permitted. Can be used as a port when the external bus read strobe
output is prohibited.
49
WR0/P84
F
External bus write strobe output
This function is valid in external bus mode. Can be used as a port
in single-chip mode.
50
WR1/P85
F
External bus write strobe output
This function is valid in external bus mode and with 16-bit buses.
Can be used as a port in single-chip mode or with external 8-bit
bus.
51
CLK/P86
F
System clock output
Outputs the same clock frequency as the external bus operation.
Can be used as a port when it is not otherwise used.
H
External interruption request inputs 0 to 3
These inputs are always used when dealing with external interruptions is permitted, so output by ports should be stopped except
when carried out intentionally.
Can be used to reset standby as input is permitted in this port under standby status.Can be used as ports when external interruption request input is not used.
53
54
55
56
57
58
59
60
INT0/PC0
INT1/PC1
INT2/PC2
INT3/PC3
AIN0/INT4/PC4
BIN0/INT5/PC5
AIN1/INT6/PC6
BIN1/INT7/PC7
External interruption request inputs 4 to 7
These inputs are always used when dealing with external interruptions is permitted, so output by ports should be stopped except
when carried out intentionally. Can be used to reset standby as input is permitted in these ports under standby status.
H
[ AIN, BIN ] Up/down timer input
This input is always used when input is permitted, so output by
ports should be stopped except when carried out intentionally.
Can be used as a port when external interruption request input and
up/down timer input are not used.
(Continued)
12
MB91133/MB91F133
Pin No.
Pin name
Circuit
type
Function
External interruption request inputs 8 to 15
These inputs are always used when dealing with external interruptions is permitted, so output by ports should be stopped except
when carried out intentionally.
[ TRG0 to 5 ] These are external trigger inputs for PPG timers.
61
62
63
64
65
66
67
68
TRG0/INT8/PD0
TRG1/INT9/PD1
TRG2/INT10/PD2
TRG3/INT11/PD3
TRG4/INT12/PD4
TRG5/INT13/PD5
DEOP2/INT14/PD6
ATG/INT15/PD7
69
70
ZIN0/PE0
ZIN1/PE1
O
Up/down timer input
These inputs are always used when input is permitted, so output
by ports should be stopped except when carried out intentionally.
Can be used as ports when up/down timer input is not used.
71
72
73
74
IN0/PE2
IN1/PE3
IN2/PE4
IN3/PE5
F
Input capture input
This function is valid when input capture activates input. Can be
used as ports when input capture input is not used.
75
FRCK/PE6
F
External clock input pin of free-run timer
Can be used as a port when external clock input of free-run timer
is not used.
76
DTTI/PE7
F
RTOn pin level fixed input
Invalid when input is permitted in the waveform generation area.
Can be used as a port when RTOn pin level fixed input is not used.
77
78
79
80
81
82
83
84
RTO0/PF0
RTO1/PF1
RTO2/PF2
RTO3/PF3
RTO4/PF4
RTO5/PF5
RTO6/PF6
RTO7/PF7
F
Output compare event pins/waveform output pins in the
waveform generation area
Can be used as ports when specification of the output compare
event pin/waveform output pin of the waveform generation area is
prohibited.
85
86
87
88
89
90
PPG0/PG0
PPG1/PG1
PPG2/PG2
PPG3/PG3
PPG4/PG4
PPG5/PG5
F
PPG timer output
This function is valid when output specification of the PPG timer is
permitted. Can be used as ports when output specification of the
PPG timer is prohibited.
111
110
109
DA0
DA1
DA2

D/A converter output
This function is valid when output specification of the D/A converter
is permitted.
O
[ DEOP2 ] DMA external transfer termination output
This function is valid when external transfer termination output
specification of the DMA controller is permitted.
[ ATG ] A/D converter external trigger input
These inputs are always used when they are selected as A/D initiation factors, so output by ports should be stopped except when
carried out intentionally. Can be used as ports when not otherwise
used.
(Continued)
13
MB91133/MB91F133
Pin No.
107
106
105
104
103
102
101
100
99
98
97
Pin name
SIN0/PH0
SOT0/PH1
SCK0/PH2
SIN1/PI0
SOT1/PI1
SCK1/PI2
SIN2/PI3
SOT2/PI4
SCK2/PI5
SIN3/PJ0
SOT3/PJ1
Circuit
type
Function
P
UART0 data input
This input is always used when UART0 activates input, so output
by ports should be stopped except when carried out intentionally.
Can be used as a port when UART0 data input is not used.
P
UART0 data output
This function is valid when UART0 data output specification is permitted. Can be used as a port when UART0 data output specification is prohibited.
P
UART0 clock input/output
This function is valid when UART0 clock output specification is permitted. Can be used as a port when UART0 clock output specification is prohibited.
P
UART1 data input
This input is always used when UART1 activates input, so output
by ports should be stopped except when carried out intentionally.
Can be used as a port when UART1 data input is not used.
P
UART1 data output
This function is valid when UART1 data output specification is permitted. Can be used as a port when UART1 data output specification is prohibited.
P
UART1 clock input/output
This function is valid when UART1 clock output specification is permitted. Can be used as a port when UART1 clock output specification is prohibited.
P
UART2 data input
This input is always used when UART2 activates input, so output
by ports should be stopped except when carried out intentionally.
Can be used as a port when UART2 data input is not used.
P
UART2 data output
This function is valid when UART2 data output specification is permitted. Can be used as a port when UART2 data output specification is prohibited.
P
UART2 clock input/output
This function is valid when UART2 clock output specification is permitted. Can be used as a port when UART2 clock output specification is prohibited.
P
UART3 data input
This input is always used when UART3 activates input, so output
by ports should be stopped except when carried out intentionally.
Can be used as a port when UART3 data input is not used.
P
UART3 data output
This function is valid when UART3 data output specification is permitted. Can be used as a port when UART3 data output specification is prohibited.
(Continued)
14
MB91133/MB91F133
Pin No.
96
95
94
Pin name
SCK3/PJ2
SIN4/PJ3
SOT4/PJ4
93
SCK4/PJ5
118
119
120
121
122
123
124
125
AN0/PK0
AN1/PK1
AN2/PK2
AN3/PK3
AN4/PK4
AN5/PK5
AN6/PK6
CMP/AN7/PK7
126
DREQ0/PL0
Circuit
type
Function
P
UART3 clock input/output
This function is valid when UART3 clock output specification is permitted. Can be used as a port when UART3 clock output specification is prohibited.
P
UART4 data input
This input is always used when UART4 activates input, so output
by ports should be stopped except when carried out intentionally.
Can be used as a port when UART4 data input is not used.
P
UART4 data output
This function is valid when UART4 data output specification is permitted. Can be used as a port when UART4 data output specification is prohibited.
P
UART4 clock input/output
This function is valid when UART4 clock output specification is permitted. Can be used as a port when UART4 clock output specification is prohibited.
A/D converter analog input
This is valid when the AICK register specification is analog input.
N
[ CMP ] level comparator input
Can be used as ports when A/D converter analog input is not used.
F
DMA external transfer request input
This input is always used if selected as the transfer factor for the
DMA controller, so output by ports should be stopped except when
carried out intentionally. Can be used as a port when DMA external transfer request input is not used.
127
DACK0/PL1
F
DMA external transfer request reception output
This function is valid when external transfer request reception output specification of the DMA controller is permitted. Can be used
as a port when transfer request reception output specification of
the DMA controller is prohibited.
128
DEOP0/PL2
F
DMA external transfer termination output
This function is valid when external transfer termination output
specification of the DMA controller is permitted.
F
DMA external transfer request input
This input is always used if selected as the transfer factor for the
DMA controller, so output by ports should be stopped except when
carried out intentionally. Can be used as a port when DMA external transfer request input is not used.
129
DREQ1/PL3
(Continued)
15
MB91133/MB91F133
(Continued)
Pin No.
Pin name
Circuit
type
Function
130
DACK1/PL4
F
DMA external transfer request reception output
This function is valid when external transfer request reception output specification of the DMA controller is permitted. Can be used
as a port when transfer request reception output specification of
the DMA controller is prohibited.
131
DEOP1/PL5
F
DMA external transfer termination output
This function is valid when external transfer termination output
specification of the DMA controller is permitted.
F
DMA external transfer request input
This input is always used if selected as the transfer factor for the
DMA controller, so output by ports should be stopped except when
carried out intentionally. Can be used as a port when DMA external transfer request input is not used.
132
DREQ2/PL6
133
DACK2/PL7
F
DMA external transfer request reception output
This function is valid when external transfer request reception output specification of the DMA controller is permitted. Can be used
as a port when transfer request reception output specification of
the DMA controller is prohibited.
134
RST
B
External reset input
136
137
X0A
X1A
K
Oscillation pin for low-speed clock (32 kHz)
139
140
X0
X1
A
Oscillation pin for high-speed clock (16.5 MHz)
142
143
144
MD0
MD1
MD2
G
Mode pins
Basic MCU operation mode is set by these pins. They should be
directly connected to VCC or VSS for use.
112
DAVS

Ground pin of D/A converter (connected to analog ground)
113
DAVC

Power pin of D/A converter
114
AVCC

Power pin for A/D converter
115
AVRH

Reference voltage pin for A/D converter (high electric potential side)
When this pin is turned on/off, AVRH or more electric potential
must be supplied to VCC.
116
AVRL

Reference voltage pin for A/D converter (low electric potential
side)
117
AVSS

Ground pin for A/D converter (connected to analog ground)
27, 108
VCC5

5 V power of digital circuit
Power must be connected to all VCC5 pins for use.
44, 92
138
VCC3

3 V power of digital circuit
Power must be connected to all VCC3 pins for use.
9, 26, 52,
91, 135,
141
VSS

Ground level of digital circuit
Note : In most of the above pins, the input/output of the I/O ports and resources are multiplexed, such as xxxx/Pxx.
If the output from ports and resources of those pins compete with each other, the resource is given priority.
16
MB91133/MB91F133
■ INPUT/OUTPUT CIRCUIT TYPES
Type
Circuit
Remarks
• High-speed oscillation circuit
(16.5 MHz)
X1
Xout
A
X0
Oscillation feedback resistance
= approximately 1 MΩ
3 V CMOS level input
Standby control signal
• With pull up resistance
CMOS level input
Pull-up resistance value
= approximately 25 kΩ (Typ.)
B
Digital input
• CMOS level input/output pin
Pout
CMOS level output
CMOS level input
(with standby control)
Nout
C
IOL = 4 mA
R
CMOS input
Standby control
• CMOS hysteresis input/output pin
Pout
CMOS level output
CMOS hysteresis input
(with standby control)
Nout
F
IOL = 4 mA
R
Hysteresis input
Standby control
(Continued)
17
MB91133/MB91F133
Type
Circuit
Remarks
• CMOS level input pin
CMOS level input
(without standby control)
G
IOL = 4 mA
R
Digital input
Pull-up control
Pout
R
• CMOS hysteresis input/output pin
with pull- up control
CMOS level output
CMOS hysteresis input
(without standby control)
Pull-up resistance value
= approximately 50 kΩ (Typ.)
H
Nout
R
Hysteresis input
IOL = 4 mA
• Clock oscillation circuit (32 kHz)
X1A
Xout
K
X0A
Oscillation feedback resistance
= approximately 4.5 MΩ/3 V
3 V CMOS level input
Standby control signal
• Analog/CMOS level input/output pin
Pout
Nout
N
R
CMOS input
Standby control
CMOS level output
CMOS level input
(with standby control)
Analog input
(Analog input is valid when bit dealt
by AIC is “1”.)
IOL = 4 mA
Analog input
(Continued)
18
MB91133/MB91F133
(Continued)
Type
Circuit
Remarks
Pull-up control
Pout
R
O
Nout
R
Hysteresis input
• CMOS hysteresis input/output pin
with pull-up control
CMOS level output
CMOS hysteresis input
(with standby control)
Pull-up resistance value
= approximately 50 kΩ (Typ.)
IOL = 4 mA
Standby control
Pull-up control
Open-drain control
R
P
Nout
R
• CMOS hysteresis input/output pin
with pull-up control
CMOS level output
(with open-drain control)
CMOS hysteresis input
(with standby control)
Pull-up resistance value
= approximately 50 kΩ (Typ)
Hysteresis input
Standby control
IOL = 4 mA
19
MB91133/MB91F133
■ HANDLING DEVICES
1. Points to Note on Handling Devices
(1) Latch-up prevention
Latch-up may occur by CMOS IC if a voltage in excess of VCC5 or lower than VSS is applied to the input/output
pins, or if the voltage exceeds the rating between VCC5 and VSS. If latch-up occurs, the electrical current increases
significantly and may destroy certain components due to excessive heat, so great care must be taken to ensure
that the maximum rating is not exceeded during use.
(2) Handling Pins
• Handling unused pins
Input pins that are not used should be pulled up or down as they may cause erroneous operations if left open.
• Handling N.C. pins
N.C. pins must be opened for use.
• Handling output pins
Excessive electric current may flow if the output pin is shorted by the power source or other output pins, or
connected to large loads. If such status is prolonged, the device is liable to be damaged, so great care must
be taken to ensure that the usage volume does not exceed the maximum rating.
• Mode pins (MD0 to MD2)
Those pins must be directly connected to VCC5 or VSS for use.
Pattern lengths between VCC5 or VSS and each mode pin on the printed-circuit board should be arranged to
be as short as possible to prevent the test mode from being erroneously turned on due to noise, and they
should be connected with low impedance.
• Power pins
When there are a number of VCC5/VCC3/VSS, those whose electrical potential must be the same within the
device are connected to prevent erroneous operation such as latch-up for device design purposes, but those
must be externally connected to a power source and earthed to follow the general output current standard and
prevent erroneous operation of strobe signals due to increased ground level and reduction in unnecessary
radiation.
Care must also be taken to ensure that they are connected to the VCC5/VSS or VCC3/VSS of this device at the
lowest possible impedance from the source of the electrical current supply.
Furthermore, it is recommended that a ceramic capacitor of around 0.1 µF be used to connect the VCC5 and
VSS, or VCC3 and VSS near the device as a bypass capacitor.
• Crystal oscillation circuits
Noise near the X0, X1, X0A or X1A pins can cause erroneous operation. The printed-circuit board must be
designed so that the X0, X1, X0A and X1A pins, crystal oscillator (or ceramic oscillator) and bypass capacitor
to the ground can be arranged as close as possible.
Also, a printed-circuit board with grounded artwork enclosing the X0, X1, X0A and X1A pins is strongly
recommended to ensure stable operation.
20
MB91133/MB91F133
(3) Points to note on usage
• External reset input
“L” level should be input to the RST pin, which is required for at least five machine cycles to ensure that the
internal status is reset.
• Oscillation pin
Oscillation pin is 3 V CMOS input level.
• External clock
Use with an external clock is prohibited. A crystal (or ceramic) oscillator should be used.
• Analog Power
The AVCC should always be used at the same electric potential as VCC5. If the VCC5 is larger than the AVCC,
electricity may flow through pins AN 0 to AN 7.
• Points to note for using level comparator
When the level comparator is used, a reference current (IR) flows even though it is stopped. The stop mode
must be turned on after prohibiting action of the level comparator.
2. Points to Note on Turning On Power
• RST pin handling
The RST pin must be started from “L” level when the power is turned on, and when the power is adjusted to
the VDD level, it should be changed to the “H” level after being left on for at least 5 cycles of the internal operation
clock.
• Original oscillation input
The clock must be input until the waiting status for oscillation stability is reset in the event that power is turned on.
• Power on reset
“Power on reset” must be executed if power is turned on, but the power voltage falls below the guaranteed
operating temperature and power is turned on again.
• Order for turning on power
Power should be turned on in the following order.
VCC3 → VCC5 → AVCC → AVRH
The opposite order should be used when turning off.
21
MB91133/MB91F133
■ BLOCK DIAGRAM
FR30 CPU
UART × 5 ch
15
SIN0 to SIN4
SOT0 to SOT4
SCK0 to SCK4
RAM 6 Kbyte
DREQ0 toDREQ 2
DACK0 toDACK 2
DEOP0 to DEOP2
DMAC 8 ch
9
Resource Bus
Controller
Reload timer × 5 ch
8 bit 3 output D/A converter
5
Bus Converter
6
6
External Bus
Controller
A23 to A00
D31 to D16
RD
WR1, WR0
RDY
BRQ
BGRNT
CLK
RAM 2 Kbyte
16 bit PPG × 6 ch
47
PPG0 to PPG5
TRG0 to TRG5
Multi-Function
Timer
ROM 254 Kbyte
16 bit ICU × 4 ch
DA0 toDA2
DAVC, DAVS
4
IN0 to IN3
Interrupt Controller
16 bit FRT
X0, X1, X0A, X1A
RST
MD0 to MD2
AIN0, 1
BIN0, 1
ZIN0, 1
Clock Generator
8
Up/Down counter × 2 ch
6
16 bit OCU × 8 ch
24 ch external interrupt
INT0 to INT23 (∗)
FRCK
RTO0 (U)
RTO1 (X)
RTO2 (V)
RTO3 (Y)
RTO4 (W)
RTO5 (Z)
RTO6
RTO7
DTTI
24
AN0 to AN7
AVRH, AVRL
AVCC, AVSS
CMP (AN7)
10 bit 8 input A/D converter
Waveform Generator
12
level comparator
* : INT23 to INT16 share pins with A23 to A16
* : INT15 shares pins with ATG
* : INT14 shares pins with DEOP2
* : INT13 to INT8 share pins with TRG5 to TRG0
* : INT7 to INT4 share pins with AIN0, BIN0, AIN1 and BIN1
The total number of above pins is 133. The remainder (144 − 133 = 11 pins) are VCC5 , VCC3 and VSS.
22
MB91133/MB91F133
■ CPU
1. Memory Space
The FR series has 4 Gbytes (232 addresses) of logic address space which the CPU accesses linearly.
• Memory Map
External ROM
external bus mode
Internal ROM
external bus mode
Single-chip mode
0000 0000H
I/O
I/O
I/O
I/O
I/O
I/O
Access is
prohibited
Access is
prohibited
Access is
prohibited
Built-in RAM 6 KB
Built-in RAM 6 KB
Built-in RAM 6 KB
Access is
prohibited
Access is
prohibited
Access is
prohibited
0000 0400H
Direct
Madressing
area
Refer to "I/O MAP"
0000 0800H
0000 1000H
0000 2800H
0001 0000H
0001 0000H
External area
Access is
prohibited
000C 0000H
External area
Built-in RAM 2KB
Built-in RAM 2KB
Built-in ROM
254KB
Built-in ROM
254KB
External area
Access is
prohibited
000C 0800H
FFFF FFFFH
010 0000H
FFFF FFFFH
* : It is impossible to access the external area on single-chip mode. When accessing the external area, select the
internal ROM external bus mode.
23
MB91133/MB91F133
2. Registers
There are two types of multi-purpose registers in the FR family. One is a dedicated purpose register that exists
within the CPU and the other is a multi-purpose register that exists in the memory.
• Dedicated Registers
Program Counter (PC)
Program Status (PS)
Table Base Register (TBR)
: 32-bit length; indicates instruction storage position.
: 32-bit length; stores register pointers and condition codes.
: Holds the starting address of the vector table to be used for Exception,
Interruption and Trapping (EIT) .
: Holds the address to return to from the sub-routine.
: Indicates the system stuck position.
: Indicates the user’s stuck position.
Return Pointer (RP)
System Stuck Pointer (SSP)
User Stuck Pointer (USP)
Multiplication and Division
Results Resister (MDH/MDL) : 32-bit length; act as registers for multiplication and division.
32 bit
PC
Program Counter
PS
Program Status
Initial values
XXXX XXXXH
(Undecided)
Table Base Register
000F FC00H
Return Pointer
XXXX XXXXH
SSP
System Stuck Pointer
0000 0000H
USP
User Stuck Pointer
XXXX XXXXH
(Undecided)
MDH
Multiplication and
Division Results Resister
XXXX XXXXH
(Undecided)
XXXX XXXXH
(Undecided)
TBR
RP
MDL
(Undecided)
• Program Status (PS)
PS is the register that holds the program status and is classified into three categories, namely, Condition Code
Register (CCR) , System Condition Code Register (SCR) and Interruption Level Master Register (ILM) .
31
PS

20
19
18
16
ILM4 ILM3 ILM2 ILM1 ILM0
ILM
24
17

10
9
8
7
6
5
4
3
2
1
0
D1
D0
T


S
I
N
Z
V
C
SCR
CCR
MB91133/MB91F133
• Condition Code Register (CCR)
S flag : Specifies the stuck pointer to be used as R15.
I flag : Controls permission and prohibition of user interruption requests.
N flag : Indicates codes when computation results are defined as integers that are expressed in complements of 2.
Z flag : Indicates whether or not a result of the computation is “0” .
V flag : Operands used for computation are defined as integers expressed in complements of 2, and indicate whether or not an overflow is generated as a result of the computation.
C flag : Indicates whether carrying or borrowing is generated from the highest bit as a result of the computation.
• System Condition Code Register (SCR)
T flag : Specifies whether or not the step trace trap will be valid.
• Interruption Level Mask Register (ILM)
ILM4 to ILM0 : Holds the interruption level mask values, and those values that are held by the ILM are used
for the level mask. Interruption requests can be accepted only when the interruption levels
handled within the interruption requests to be input into the CPU are stronger than the levels
shown by the ILM.
ILM4
ILM3
ILM2
ILM1
ILM0
Interruption level
Strength
0
0
0
0
0
0
Strong
0
1
0
0
0
15
1
1
1
1
1
31
Weak
25
MB91133/MB91F133
■ MULTI-PURPOSE REGISTERS
The multi-purpose registers are CPU registers R0 to R15 which are used as accumulators for various computations and memory access pointers (fields that indicate the address) .
• Register bank configuration
32-bit
R0
Initial value
XXXX XXXXH
R1
R12
R13
AC (Accumulator)
R14
FP (Frame Pointer)
XXXX XXXXH
R15
SP (Stack Pointer)
0000 0000H
Special purposes are assumed for the following 3 of the 16 registers. Thus, some instructions are emphasized.
R13 : Virtual accumulator (AC)
R14 : Frame Pointer (FP)
R15 : Stack Pointer (SP)
Initial values for R0 to R14 on resetting are unspecified. The initial value of R15 will be 0000 0000H (SSP value) .
26
MB91133/MB91F133
■ MODE SETTING
1. Pins
• Mode pins and set mode
Mode pins
Mode name
MD2 MD1 MD0
Reset vector
access areas
External data
bus width
Bus modes
0
0
0
External vector mode 0
External
8-bit
0
0
1
External vector mode 1
External
16-bit
0
1
0



0
1
1
Internal vector mode
Internal
(Mode register)
1





External ROM external
bus mode
Setting is prohibited
Single chip mode
Usage is prohibited
2. Register
Mode register (MODR) and set mode
Address
0000 07FFH
M1
M0
*
*
*
*
*
*
Initial value Access
XXXX XXXXB
W
Bus mode set bit
W : Write only
X : Undecided
* : “0” should always be written for bits other than M1 and M0.
• Bus mode set bit and its functions
M1
M0
Functions
0
0
Single chip mode
0
1
Internal ROM external bus mode
1
0
External ROM external bus mode
1
1

Remarks
Setting is prohibited
27
MB91133/MB91F133
■ I/O MAP
Register
Address
000000H
+0
PDR3
+1
(R/W)
PDR2
XXXXXXXX
000004H

000008H

+2
(R/W)
(R/W)
000014H
000018H
00001CH
000020H
000024H
000028H
PDRF
(R/W)
XXXXXXXX


00003CH
000040H
PDRE
XXXXXXXX
PDRJ
PDRI
- - XXXXXX
LVLC
(R/W)
(R/W)

SIDR0/SODR0 (R/W)
0 0 0 0 1 -00
SSR1
(R/W)
XXXXXXXX
SIDR1/SODR1 (R/W)
0 0 0 0 1 -00
SSR2
(R/W)
(R/W)
- - XXXXXX
XXXX 0 0 0 0
SSR0
(R/W)
XXXXXXXX
(R/W)
PDR4
(R/W)
XXXXXXXX
PDR8
(R/W)
- XXXXXXX
XXXXXXXX
SIDR2/SODR2 (R/W)
PDRD
(R/W)
XXXXXXXX
PDRH
(R/W)
- - - - - XXX
PDRL
(R/W)
XXXXXXXX
SCR0
(R/W)
00000100
SCR1
(R/W)
00000100
SCR2
(R/W)
PDRC
XXXXXXXX
PDRG
(R/W)
- - XXXXXX
PDRK
(R/W)
XXXXXXXX
SMR0
(R/W)
0 0 0 0 0-0 0
SMR1
(R/W)
0 0 0 0 0-0 0
SMR2
(R/W)
XXXXXXXX
00000100
0 0 0 0 0-0 0
TMRLR
(W)
TMR
(R)
XXXXXXXX XXXXXXXX

TMRLR
XXXXXXXX XXXXXXXX
UART0
UART1
UART2
Reload Timer 0
(R)
XXXXXXXX XXXXXXXX
(R/W)
Reload Timer 1
----0000 0 0 0 0 0 0 0 0
(R/W)
0 0 1 0 1 - XX XXXXXXXX
(W)
XXXXXXXX XXXXXXXX

TMR
TMCSR

TMRLR
(R/W)
Level Comparator
----0000 0 0 0 0 0 0 0 0
(W)
ADCR
XXXXXXXX XXXXXXXX
TMCSR
Port Data
Register
(R/W)
0 0 0 0 1 -00
000034H
000038H
(R/W)

00002CH
000030H
PDR5
XXXXXXXX
00000CH
000010H

XXXXXXXX
PDR6
Block
+3
ADCS1
(R/W)
ADCS0
(R/W)
00000000
00000000
TMR
(R)
XXXXXXXX XXXXXXXX
TMCSR
(R/W)
A/D Converter
(Sequential type)
Reload Timer 2
----0000 0 0 0 0 0 0 0 0
(Continued)
28
MB91133/MB91F133
Register
Address
000044H
000048H
+0
+1
+2
+3
IPCP1
(R)
IPCP0
(R)
XXXXXXXX XXXXXXXX
XXXXXXXX XXXXXXXX
IPCP3
IPCP2
(R)
XXXXXXXX XXXXXXXX
ICS23

00004CH
000058H
00005CH
000060H
000064H
000068H
00006CH
000070H
000074H
000078H
00007CH
000080H
(R)
XXXXXXXX XXXXXXXX
(R/W)
ICS01

00000000
OCCP1
(R/W)
XXXXXXXX XXXXXXXX
OCCP3
(R/W)
XXXXXXXX XXXXXXXX
OCCP5
(R/W)
XXXXXXXX XXXXXXXX
OCCP7
(R/W)
XXXXXXXX XXXXXXXX
OCS32
(R/W)
XXX 0 0 0 0 0 0 0 0 0 XX 0 0
OCS76
(R/W)
XXX 0 0 0 0 0 0 0 0 0 XX 0 0
TCDT
(R/W)
00000000
Reserved
OCCP0
(R/W)
SIDR3/SODR3 (R/W)
0 0 0 0 1 0 00
SSR4
(R/W)
XXXXXXXX
SIDR4/SODR4 (R/W)
0 0 0 0 1 0 00
CDCR1
XXXXXXXX
(R/W)

0 ---0 0 0 0
CDCR3
(R/W)

0 ---0 0 0 0

(R/W)
XXXXXXXX XXXXXXXX
OCCP2
(R/W)
XXXXXXXX XXXXXXXX
OCCP4
(R/W)
XXXXXXXX XXXXXXXX
OCCP6
(R/W)
16-bit OCU
XXXXXXXX XXXXXXXX
OCS10
(R/W)
XXX 0 0 0 0 0 0 0 0 0 XX 0 0
OCS54
(R/W)
XXX 0 0 0 0 0 0 0 0 0 XX 0 0
TCCS
00000000 00000000
SSR3
16-bit ICU
(R/W)

000050H
000054H
Block
(R/W)
0------- 0 0 0 0 0 0 0 0
SCR3
(R/W)
00000100
SCR4
(R/W)
00000100
CDCR0
(R/W)
0 ---0 0 0 0
CDCR2
(R/W)
0 ---0 0 0 0
CDCR4
(R/W)
0 ---0 0 0 0
SMR3
(R/W)
0 0 0 0 0-0 0
SMR4
(R/W)
0 0 0 0 0-0 0
16-bit
Free-run Timer
UART3
UART4


Communication
Pre-scalar

(Continued)
29
MB91133/MB91F133
Register
Address
000084H
000088H
00008CH
+0
RCR1
+1
(W)
00000000
CCRH0
(R/W)
00000000
CCRH1
(R/W)
-0 0 0 0 0 0 0
+2
RCR0
(W)
CCRL0
000098H
00009CH
0000A0H
(R/W)
EIRR0
(R/W)
ENIR0
(R/W)
00000000
CSR1
00000000
Reserved
EIRR1
(R/W)
ENIR1
(R/W)
00000000
ELVR0
(R/W)
ELVR1
(R/W)
00000000 00000000
EIRR2
(R/W)
ENIR2
00000000 00000000
(R/W)
00000000
00000000
ELVR2
(R/W)
DACR2

DACR1
-------0

DTCR1
(R/W)
DADR2
(R/W)
00000000
TMRR1
DADR1
(R/W)
XXXXXXXX
(R/W)
DTCR0
XXXXXXXX
SIGCR

(R/W)
-------0
XXXXXXXX
(R/W)
(R/W)
00000000
(R/W)
DTCR2
00000000
(R/W)
00000000
DACR0
(R/W)
-------0
DADR0
(R/W)
PCRE

PCRJ
------0 0
(R/W)
--0 0 0 0 0 0
OCRJ
(R/W)
(R/W)
PCRI
(R/W)
--0 0 0 0 0 0
OCRI
(R/W)
D/A Converter
XXXXXXXX
TMRR0
(R/W)
XXXXXXXX
TMRR2
(R/W)
Waveform
Generator
XXXXXXXX

0000C0H
Ext Int

00000000 00000 000

8-/16-bit
U/D Counter
(R/W)
00000000
0000B4H
to
0000BCH
0000CCH
(R/W)
00000000
0000B0H
0000C8H
CSR0
00000000
0000A8H
0000C4H
00000000

-0 0 0 1 0 0 0
(R)

0000A4H
0000ACH
UDCR0

-0 0 0 1 0 0 0
CCRL1
(R)
00000000
(R/W)
000090H
000094H
UDCR1
00000000
Block
+3
Reserved
PCRD
(R/W)
00000000
PCRH
PCRC
00000000
(R/W)
(R/W)
--0 0 0 0 0 0
--0 0 0 0 0 0
-----0 0 0



Pull-up Control

-----0 0 0
OCRH
(R/W)

AICK
Open-drain Control
(R/W)
00000000
Analog
Input Control
(Continued)
30
MB91133/MB91F133
Register
Address
0000D0H
0000D4H
0000D8H
0000DCH
0000E0H
0000E4H
0000E8H
0000ECH
0000F0H
0000F4H
0000F8H
0000FCH
000100H
000104H
000108H
00010CH
+0
DDRF
+1
(R/W)
00000000
DDRJ
(R/W)
DDRE
+2
(R/W)
00000000
DDRI
(R/W)
--0 0 0 0 0 0
--0 0 0 0 0 0


GCN1
(R/W)
DDRD
00000000
(R)
11111111 11111111
PDUT0
(W)
XXXXXXXX XXXXXXXX
PTMR1
(R)
11111111 11111111
PDUT1
(W)
XXXXXXXX XXXXXXXX
PTMR2
(R)
11111111 11111111
PDUT2
(W)
XXXXXXXX XXXXXXXX
PTMR3
(R)
11111111 11111111
PDUT3
(W)
XXXXXXXX XXXXXXXX
PTMR4
(R)
11111111 11111111
PDUT4
(W)
XXXXXXXX XXXXXXXX
PTMR5
(R)
11111111 11111111
PDUT5
(W)
XXXXXXXX XXXXXXXX
(R/W)
-----0 0 0
DDRL
(R/W)
00000000
DDRC
(R/W)
00000000
DDRG
(R/W)
--0 0 0 0 0 0
DDRK
00000000
(R/W)
00000000
PCSR0
(R/W)
PCNL0
(R/W)
0000000-
00000000
PCSR1
(W)
XXXXXXXX XXXXXXXX
PCNH1
(R/W)
PCNL1
(R/W)
0000000-
00000000
PCSR2
(W)
XXXXXXXX XXXXXXXX
PCNH2
(R/W)
PCNL2
(R/W)
0000000-
00000000
PCSR3
(W)
XXXXXXXX XXXXXXXX
PCNH3
(R/W)
PCNL3
(R/W)
0000000-
00000000
PCSR4
(W)
XXXXXXXX XXXXXXXX
PCNH4
(R/W)
PCNL4
(R/W)
0000000-
00000000
PCSR5
(W)
XXXXXXXX XXXXXXXX
PCNH5
(R/W)
0000000-
PPG ctl
(W)
XXXXXXXX XXXXXXXX
PCNH0
Data Direction
Register
(R/W)
GCN2

00110010 00010000
PTMR0
(R/W)
DDRH
Block
+3
PCNL5
(R/W)
PPG0
PPG1
PPG2
PPG3
PPG4
PPG5
00000000
(Continued)
31
MB91133/MB91F133
Register
Address
000110H
+0
+1
+2
+3
TMRLR
(W)
TMR
(R)
XXXXXXXX XXXXXXXX
000118H
TMCSR
(W)
TMR
XXXXXXXX XXXXXXXX
XXXXXXXX XXXXXXXX

--------
--------
--------
00000000 00000000
DATCR
XXXX0 0 0 0
(R/W)

000210H
to
0003ECH

BSD0
XXXXXXXX
XXXXXXXX
BSDC
0003F8H
XXXXXXXX
XXXXXXXX
BSRR
0003FCH
000408H
XXXXXXXX
BSD1
0003E4H
XXXXXXXX
ICR00
(R/W)
----1 1 1 1
ICR04
(R/W)
----1 1 1 1
ICR08
(R/W)
----1 1 1 1
XXXXXXXX
ICR01
(R/W)
----1 1 1 1
ICR05
(R/W)
----1 1 1 1
ICR09
(R/W)
----1 1 1 1
DMAC
XXXX0 0 0 0 XXXX0 0 0 0
00020CH
XXXXXXXX
-0 0 0 0 0 0 0
(R/W)
00000000 00000000
XXXXXXXX
Reserved
(R/W)
DACSR
0003F0H
Reload Timer 4
----0000 0 0 0 0 0 0 0 0
DPDP
000208H
000404H
(R/W)

000200H
Reload Timer 3
(R)
TMCSR
000120H
to
0001FCH
000400H
(R/W)
----0000 0 0 0 0 0 0 0 0
TMRLR
00011CH
000204H
XXXXXXXX XXXXXXXX

000114H
Block
Reserved
(W)
XXXXXXXX XXXXXXXX
(R/W)
XXXXXXXX XXXXXXXX
Bit Search Module
(W)
XXXXXXXX XXXXXXXX
(R)
XXXXXXXX XXXXXXXX
ICR02
(R/W)
----1 1 1 1
ICR06
(R/W)
----1 1 1 1
ICR10
(R/W)
----1 1 1 1
ICR03
(R/W)
----1 1 1 1
ICR07
(R/W)
----1 1 1 1
ICR11
Interrupt Control
Unit
(R/W)
----1 1 1 1
(Continued)
32
MB91133/MB91F133
Register
Address
00040CH
000410H
000414H
000418H
00041CH
000420H
000424H
000428H
00042CH
000430H
+0
ICR12
+1
(R/W)
----1 1 1 1
ICR16
(R/W)
----1 1 1 1
ICR20
(R/W)
----1 1 1 1
ICR24
(R/W)
----1 1 1 1
ICR28
(R/W)
----1 1 1 1
ICR32
(R/W)
----1 1 1 1
ICR36
(R/W)
----1 1 1 1
ICR40
(R/W)
----1 1 1 1
ICR44
(R/W)
----1 1 1 1
DICR
(R/W)
-------0
ICR13
+2
(R/W)
----1 1 1 1
ICR17
000484H
000488H
00048CH
to
0005FCH
ICR18
----1 1 1 1
ICR21
(R/W)
ICR39
(R/W)
ICR46
ICR43
(R/W)
(R/W)
----1 1 1 1
(R/W)
ICR47
----1 1 1 1
(R/W)
(R/W)
----1 1 1 1
----1 1 1 1
(R/W)
(R/W)
----1 1 1 1

---1 1 1 1 1
Delay Int

RSRR/WTCR (R/W)
1 XXXX - 0 0
GCR
(R/W)
1 1 0 0 1 1-1
CT
STCR
(R/W)
WPR
Reserved
PDRR
0 0 0 1 1 1--
Interrupt Control
Unit
----1 1 1 1
(R/W)
ICR42
----1 1 1 1
HRCL
ICR35
----1 1 1 1
(R/W)
(R/W)
----1 1 1 1
(R/W)
ICR38
----1 1 1 1
ICR45
ICR31
----1 1 1 1
(R/W)
(R/W)
----1 1 1 1
(R/W)
ICR34
----1 1 1 1
ICR41
ICR27
----1 1 1 1
(R/W)
(R/W)
----1 1 1 1
(R/W)
ICR30
----1 1 1 1
ICR37
ICR23
----1 1 1 1
(R/W)
(R/W)
----1 1 1 1
(R/W)
ICR26
----1 1 1 1
ICR33
ICR19
----1 1 1 1
(R/W)
(R/W)
----1 1 1 1
(R/W)
ICR22
----1 1 1 1
ICR29
ICR15
----1 1 1 1
----1 1 1 1
ICR25
(R/W)
----1 1 1 1
(R/W)
000434H
to
00047CH
000480H
ICR14
Block
+3
(R/W)
CTBR
----0 0 0 0
(W)
(W)
XXXXXXXX
Clock Control Unit

XXXXXXXX
(R/W)

0 0--0-0 0

PLL Control
Reserved
(Continued)
33
MB91133/MB91F133
Register
Address
000600H
+0
DDR3
(W)
00000000
000604H

000608H
00060CH
000610H
000614H
000618H
00061CH
000620H
000624H
000628H
+1
DDR2
DDR6

(W)
DDR5
(W)
00000000



ASR1
(W)
AMR1
00000000 00000001
ASR2
(W)
ASR3
(W)
---0 0 1 1 1
AMD5
(W)
(W)
AMR4
(W)
00000000 00000000
(W)
AMD1
(W)
00000000 00000000
AMR5
00000000 00000101
(R/W)
(W)
-0 0 0 0 0 0 0
AMR3
00000000 00000100
AMD0
DDR8
Data Direction
Register
00000000 00000000
00000000 00000011
ASR5
(W)
00000000
AMR2
(W)
ASR4
DDR4
Block
00000000 00000000
00000000 00000010
(W)
00000000 00000000
(R/W)
AMD32
0--0 0 0 0 0
(R/W)
AMD4
00000000
(R/W)
T-unit
(R/W)
0--0 0 0 0 0

0--0 0 0 0 0
EPCR0
(W)
EPCR1
----1 1 0 0 -1------
(W)
-------- 1 1 1 1 1 1 1 1

PCR6

(R/W)

00000000
000634H
to
0007BCH
0007C8H
to
0007F8H

00000000
00000000
000630H
0007C4H
+3
(W)
00062CH
0007C0H
+2

FLCR
(R/W)
Reserved

000X0000
FWTC
Pull-up Control
FLASH Control
(R/W)

-----0 0 0

Reserved
(Continued)
34
MB91133/MB91F133
(Continued)
Address
0007FCH
Register
+0
+1

+2
LER
Block
+3
(W)
MODR
-----0 0 0
(W)
XXXXXXXX
Little Endian
Register
Mode Register
*1 : Do not execute RMW instructions to registers with write-only bits.
*2 : Do not execute write access to read-only or reserved registers except for particular requests.
*3 : Data in areas with “-” or reserved ones are unspecified.
*4 : RMW instructions (RMW : Read / Modify / Write)
AND
Rj, @Ri
OR
Rj, @Ri
ANDH Rj, @Ri
ORH Rj, @Ri
ANDB Rj, @Ri
ORB Rj, @Ri
BANDL #u4, @Ri
BORL #u4, @Ri
BANDH #u4, @Ri
BORH #u4, @Ri
EOR
EORH
EORB
BEORL
BEORH
Rj, @Ri
Rj, @Ri
Rj, @Ri
#u4, @Ri
#u4, @Ri
35
MB91133/MB91F133
■ INTERRUPTION VECTOR
Causes of MB91130 interruptions and allocation of interruption vectors and interruption control registers are
described in the interruption vector table.
Interruption number
Interruption
Address *2
Interruption sauce
Offset
*1
of
TBR default
level
Decimal Hexadecimal
Reset
0
00

3FCH
000FFFFCH
System reservation
1
01

3F8H
000FFFF8H
System reservation
2
02

3F4H
000FFFF4H
System reservation
3
03

3F0H
000FFFF0H
System reservation
4
04

3ECH
000FFFECH
System reservation
5
05

3E8H
000FFFE8H
System reservation
6
06

3E4H
000FFFE4H
System reservation
7
07

3E0H
000FFFE0H
System reservation
8
08

3DCH
000FFFDCH
System reservation
9
09

3D8H
000FFFD8H
System reservation
10
0A

3D4H
000FFFD4H
System reservation
11
0B

3D0H
000FFFD0H
System reservation
12
0C

3CCH
000FFFCCH
System reservation
13
0D

3C8H
000FFFC8H
Exceptions to undefined instructions
14
0E

3C4H
000FFFC4H
System reservation
15
0F

3C0H
000FFFC0H
External interruption 0
16
10
ICR00
3BCH
000FFFBCH
External interruption 1
17
11
ICR01
3B8H
000FFFB8H
External interruption 2
18
12
ICR02
3B4H
000FFFB4H
External interruption 3
19
13
ICR03
3B0H
000FFFB0H
External interruption 4
20
14
ICR04
3ACH
000FFFACH
External interruption 5
21
15
ICR05
3A8H
000FFFA8H
External interruption 6
22
16
ICR06
3A4H
000FFFA4H
External interruption 7
23
17
ICR07
3A0H
000FFFA0H
External interruption 8 to 15
24
18
ICR08
39CH
000FFF9CH
External interruption 16 to 23
25
19
ICR09
398H
000FFF98H
UART0 (Reception completion)
26
1A
ICR10
394H
000FFF94H
UART1 (Reception completion)
27
1B
ICR11
390H
000FFF90H
UART2 (Reception completion)
28
1C
ICR12
38CH
000FFF8CH
UART3 (Reception completion)
29
1D
ICR13
388H
000FFF88H
UART4 (Reception completion)
30
1E
ICR14
384H
000FFF84H
(Continued)
36
MB91133/MB91F133
Interruption sauce
Interruption number
Interruption
level *1
Decimal Hexadecimal
Offset
Address *2
of TBR default
UART0 (Transmission completion)
31
1F
ICR15
380H
000FFF80H
UART1 (Transmission completion)
32
20
ICR16
37CH
000FFF7CH
UART2 (Transmission completion)
33
21
ICR17
378H
000FFF78H
UART3 (Transmission completion)
34
22
ICR18
374H
000FFF74H
UART4 (Transmission completion)
35
23
ICR19
370H
000FFF70H
DMAC (end, error)
36
24
ICR20
36CH
000FFF6CH
Reload timer 0
37
25
ICR21
368H
000FFF68H
Reload timer 1
38
26
ICR22
364H
000FFF64H
Reload timer 2
39
27
ICR23
360H
000FFF60H
Reload timer 3
40
28
ICR24
35CH
000FFF5CH
Reload timer 4
41
29
ICR25
358H
000FFF58H
A/D (sequential type)
42
2A
ICR26
354H
000FFF54H
PPG0
43
2B
ICR27
350H
000FFF50H
PPG1
44
2C
ICR28
34CH
000FFF4CH
PPG2
45
2D
ICR29
348H
000FFF48H
PPG3
46
2E
ICR30
344H
000FFF44H
PPG4/5
47
2F
ICR31
340H
000FFF40H
Waveform generator
48
30
ICR32
33CH
000FFF3CH
U/D counter 0 (compare/
underflow-overflow, up/down invert)
49
31
ICR33
338H
000FFF38H
U/D counter 1 (compare/
underflow-overflow, up/down invert)
50
32
ICR34
334H
000FFF34H
ICU0 (load)
51
33
ICR35
330H
000FFF30H
ICU1 (load)
52
34
ICR36
32CH
000FFF2CH
ICU2 (load)
53
35
ICR37
328H
000FFF28H
ICU3 (load)
54
36
ICR38
324H
000FFF24H
OCU0 (matched)
55
37
ICR39
320H
000FFF20H
OCU1 (matched)
56
38
ICR40
31CH
000FFF1CH
OCU2 (matched)
57
39
ICR41
318H
000FFF18H
OCU3 (matched)
58
3A
ICR42
314H
000FFF14
OCU4/5 (matched)
59
3B
ICR43
310H
000FFF10H
OCU6/7 (matched)
60
3C
ICR44
30CH
000FFF0CH
Level comparator
61
3D
ICR45
308H
000FFF08H
16-bit freerun timer
62
3E
ICR46
304H
000FFF04H
Delay interruption factor bit
63
3F
ICR47
300H
000FFF00H
(Continued)
37
MB91133/MB91F133
(Continued)
Interruption sauce
Interruption number
Interruption
level *1
Decimal Hexadecimal
Offset
Address *2
of TBR default
System reservation
(used under REALOS *3)
64
40

2FCH
000FFEFCH
System reservation
(used under REALOS *3)
65
41

2F8H
000FFEF8H
Used under INT instruction
66
42

2F4H
000FFEF4H
Used under INT instruction
67
43

2F0H
000FFEF0H
Used under INT instruction
68
44

2ECH
000FFEECH
Used under INT instruction
69
45

2E8H
000FFEE8H
Used under INT instruction
70
46

2E4H
000FFEE4H
Used under INT instruction
71
47

2E0H
000FFEE0H
Used under INT instruction
72
48

2DCH
000FFEDCH
Used under INT instruction
73
49

2D8H
000FFED8H
Used under INT instruction
74
4A

2D4H
000FFED4H
Used under INT instruction
75
4B

2D0H
000FFED0H
Used under INT instruction
76
4C

2CCH
000FFECCH
Used under INT instruction
77
4D

2C8H
000FFEC8H
Used under INT instruction
78
4E

2C4H
000FFEC4H
Used under INT instruction
79
4F

2C0H
000FFEC0H
Used under INT instruction
80
to
255
50
to
FF

2BCH
to
000H
000FFEBCH
to
000FFC00H
*1 : ICR sets the interruption level for each interruption request using the register built into the interruption controller.
ICR is prepared in accordance with each interruption request.
*2 : TBR is the register that indicates the starting address of the vector table for EIT.
Addresses with added offset values that are specified per TBR and EIT factor will be the vector addresses.
*3 : 0X40, 0X41 interruptions for system codes are used in the event that REALOS/FR is used.
38
MB91133/MB91F133
■ PERIPHERAL RESOURCES
1. Bus Interface
The bus interface controls the interface with external memory and external I/O.
•
•
•
•
•
•
•
Bus Interface Characteristics
24-bit (16 MB) address output
16/8-bit bus width can be set.
Insertion of programmable “automatic memory wait” (maximum of 7 cycles)
Supports “little endian” mode
Unused addresses / data pins can be used as I/O ports.
Clock doubled should be used if the external bus exceeds 25 MHz. Bus speed is 1/2 of the CPU speed.
• Areas
A total of six types of chip selection areas are prepared for the bus interface. The position of each area can be
randomly arranged per 64 KB at least using area selection registers (ASR1 to ASR 5) and area mask registers
(AMR1 to AMR 5) in an area of 4 GB. The area 0 is allocated to space outside the area specified by ASR1 to
ASR5. External areas other than 00010000H to 0005FFFFH are deemed area 0 on resetting.
There is no chip selection output pin so no setting is required. Setting it has no effect on usage.
Figure 4.1-1 shows an example in which areas 1 to 5 are arranged from 00100000H to 0014FFFFH in 64 KB
units. Also, Figure 4.1-2 shows an example in which area 1 is arranged as 00000000H to 0007FFFFH in 512 KB
and areas 2 to 5 are arranged as 00100000H to 004FFFFFH in 1-MB units.
00000000H
00080000H
CS0 (1 Mbyte)
00000000H
CS1 (512 K)
00080000H
CS0 (512 K)
000FFFFFH
CS2 (1 Mbyte)
000FFFFFH
001FFFFFH
0010FFFFH
CS1 (64 Kbyte)
0011FFFFH
CS2 (64 Kbyte)
0012FFFFH
CS3 (64 Kbyte)
0013FFFFH
CS4 (64 Kbyte)
0014FFFFH
CS5 (64 Kbyte)
CS3 (1 Mbyte)
002FFFFFH
CS4 (1 Mbyte)
003FFFFFH
CS5 (1 Mbyte)
004FFFFFH
CS0
Figure 4.1-1
Area Arrangement Example 1
CS0
Figure 4.1-2
Area Arrangement Example 2
39
MB91133/MB91F133
A - Out
DATA BUS
ADDRESS BUS
• Block Diagram
write
buffer
switch
read
buffer
switch
M
U
X
External
DATA Bus
DATA BLOCK
ADDRESS BLOCK
+1 or +2
address
buffer
External
Address Bus
shifter
inpage
CS0 - CS5
comparator
ASR
AMR
External pin control area
RD
WR0. WR1
Controls all blocks
registers
&
Control
40
BRQ
BGRNT
RDY
MB91133/MB91F133
• Register List
Address
8 7
15
0
0000060CH
ASR1
Area Select Register 1
0000060EH
AMR1
Area Mask Register 1
00000610 H
ASR2
Area Select Register 2
00000612 H
AMR2
Area Mask Register 2
00000614 H
ASR3
Area Select Register 3
00000616 H
AMR3
Area Mask Register 3
00000618 H
ASR4
Area Select Register 4
0000061AH
AMR4
Area Mask Register 4
0000061CH
ASR5
Area Select Register 5
0000061EH
AMR5
Area Mask Register 5
00000620 H
AMD0
AMD1
Area Mode Register 0 / Area Mode Register 1
00000622 H
AMD32
AMD4
Area Mode Register 32 / Area Mode Register 4
00000624 H
AMD5

Area Mode Register 5
00000626 H
RFCR
ReFresh Control Register
0000062CH
DMCR4
DRAM Control Register 4
0000062EH
DMCR5
DRAM Control Register 4
00000688 H
EPCR0
EPCR1
External Pin Control Register
000007FEH
LER
MODR
Little Endian Register / MODe Register
Note : Functional pins have not been prepared in the shaded area for MB91133/MB91F133, so these
registers should not be accessed.
41
MB91133/MB91F133
2. I/O Port
MB91133/MB91F133 can be used as an I/O port when the setting for resources dealing with each pin does not
use the pin for input/output.
As regards the read value of the port (PDR) , the pin level is read out when input is set for the port. If output is
set, the data register value is read out. This is the same for reading under Read Modify Write.
If the input setting is changed to output setting, output data should be set first. If Read Modify Write instructions
(i.e. bit set) are used in this case, the data that is read out is the input data from the pin and is not the latch value
of the data register, so care must be taken.
• Basic I/O Port Block Diagram
Data bus
Resource input
0
1
PDR read
pin
0
PDR
Resource output
DDR
1
Resource output
permission
PDR : Port Data Register
DDR : Data Direction Register
• I/O Port Register
The I/O port consists of the Port Data Register (PDR) and Port Direction Register (DDR) .
• In case of input mode (DDR = “0”)
When PDR reads : Level of external pins handled is read out.
When PDR writes : Set value is written in PDR.
• In case of output mode (DDR = “1”)
When PDR reads : PDR values are read out.
When PDR writes : PDR values are output to the external pin handled.
• Switching control for resources and ports of the analog pin (A/D)
• Resources and ports of the analog pin (A/D) are switched using the Analog Input Control register on Port K
(AICK) .
This controls whether Port K is used as an analog or general-purpose port.
0 : General-purpose port
1 : Analog input (A/D)
42
MB91133/MB91F133
• Block Diagram of Input/Output Port (with Pull-up Resistance)
Data bus
Resource input
0
Pull up resistance
1
PDR read
(approximately
50 kΩ)
pin
0
PDR
Resource output
DDR
1
Resource output
permission
PCR
PDR : Port Data Register
DDR : Data Direction Register
PCR : Pull-up Control Register
• Pull-up resistance control register (PCR) R/W
Turns pull-up resistance ON/OFF.
0 : Pull-up resistance turned off
1 : Pull-up resistance turned on
Notes : • The pull-up resistance control register setting is handled as a priority in stop mode (HIZ = 1) as well.
• Use of the pull-up resistance control function is prohibited when the pin concerned is used as the external
bus pin. “1” should not be written in this register.
43
MB91133/MB91F133
• Block Diagram of Input / Output Port (Open-drain Output Function with Pull-up Resistance)
Data bus
Resource input
0
1
PDR read
pin
0
PDR
Resource output
1
Resource output
permission
DDR
ODCR
PCR
PDR : Port Data Register
DDR : Data Direction Register
ODCR : OpenDrain Control Register
PCR : Pull-up Control Register
• Pull-up resistance control register (PCR) R/W
Controls pull up resistance ON/OFF.
0 : Without pull-up resistance
1 : With pull-up resistance
• Open-drain control register (ODCR) R/W
Controls open-drain in output mode.
0 : Standard output port in output mode
1 : Open-drain output port in output mode
Notes : • This has no meaning in input mode (output Hi-Z) . Input/output mode is decided by the Direction Register
(DDR) .
• Pull-up resistance control register setting is handled as the priority in stop mode (HIZ = 1) as well.
• Use of both the pull-up resistance control function and open-drain control function are prohibited when the
pin concerned is used as an external bus pin. “1” should not be written in both registers.
44
MB91133/MB91F133
• Port Data Register (PDR)
PDR2
7
6
5
4
3
2
1
0
Initial value
Access
Address : 000001H
P27
P26
P25
P24
P23
P22
P21
P20
XXXXXXXXB
R/W
PDR3
7
6
5
4
3
2
1
0
Initial value
Access
Address : 000000H
P37
P36
P35
P34
P33
P32
P31
P30
XXXXXXXXB
R/W
PDR4
7
6
5
4
3
2
1
0
Initial value
Access
Address : 000007H
P47
P46
P45
P44
P43
P42
P41
P40
XXXXXXXXB
R/W
PDR5
7
6
5
4
3
2
1
0
Initial value
Access
Address : 000006H
P57
P56
P55
P54
P53
P52
P51
P50
XXXXXXXXB
R/W
PDR6
7
6
5
4
3
2
1
0
Initial value
Access
Address : 000005H
P67
P66
P65
P64
P63
P62
P61
P60
XXXXXXXXB
R/W
PDR8
7
6
5
4
3
2
1
0
Initial value
Access
Address : 00000BH

P86
P85
P84
P83
P82
P81
P80
- XXXXXXXB
R/W
PDRC
7
6
5
4
3
2
1
0
Initial value
Access
Address : 000013H
PC7
PC6
PC5
PC4
PC3
PC2
PC1
PC0
XXXXXXXXB
R/W
PDRD
7
6
5
4
3
2
1
0
Initial value
Access
Address : 000012H
PD7
PD6
PD5
PD4
PD3
PD2
PD1
PD0
XXXXXXXXB
R/W
PDRE
7
6
5
4
3
2
1
0
Initial value
Access
Address : 000011H
PE7
PE6
PE5
PE4
PE3
PE2
PE1
PE0
XXXXXXXXB
R/W
PDRF
7
6
5
4
3
2
1
0
Initial value
Access
Address : 000010H
PF7
PF6
PF5
PF4
PF3
PF2
PF1
PF0
XXXXXXXXB
R/W
PDRG
7
6
5
4
3
2
1
0
Initial value
Access
Address : 000017H


PG5
PG4
PG3
PG2
PG1
PG0
- - XXXXXXB
R/W
PDRH
7
6
5
4
3
2
1
0
Initial value
Access
Address : 000016H





PH2
PH1
PH0
- - - - - XXXB
R/W
PDRI
7
6
5
4
3
2
1
0
Initial value
Access
Address : 000015H


PI5
PI4
PI3
PI2
PI1
PI0
- - XXXXXXB
R/W
PDRJ
7
6
5
4
3
2
1
0
Initial value
Access
Address : 000014H


PJ5
PJ4
PJ3
PJ2
PJ1
PJ0
- - XXXXXXB
R/W
PDRK
7
6
5
4
3
2
1
0
Initial value
Access
Address : 00001BH
PK7
PK6
PK5
PK4
PK3
PK2
PK1
PK0
XXXXXXXXB
R/W
PDRL
7
6
5
4
3
2
1
0
Initial value
Access
Address : 00001AH
PL7
PL6
PL5
PL4
PL3
PL2
PL1
PL0
XXXXXXXXB
R/W
PDR2 to L are input/output data registers of the I/O port.
Input/output control is carried out by DDR2 to L that are handled.
45
MB91133/MB91F133
• Data Direction Register (DDR)
DDR2
7
6
5
4
3
2
1
0
Address : 000601H
P27
P26
P25
P24
P23
P22
P21
P20
DDR3
7
6
5
4
3
2
1
0
Address : 000600H
P37
P36
P35
P34
P33
P32
P31
P30
DDR4
7
6
5
4
3
2
1
0
Address : 000607H
P47
P46
P45
P44
P43
P42
P41
P40
DDR5
7
6
5
4
3
2
1
0
Address : 000606H
P57
P56
P55
P54
P53
P52
P51
P50
DDR6
7
6
5
4
3
2
1
0
Address : 000605H
P67
P66
P65
P64
P63
P62
P61
P60
7
6
5
4
3
2
1
0
Address : 00060BH

P86
P85
P84
P83
P82
P81
P80
DDRC
7
6
5
4
3
2
1
0
Address : 0000D3H
PC7
PC6
PC5
PC4
PC3
PC2
PC1
PC0
DDRD
7
6
5
4
3
2
1
0
Address : 0000D2H
PD7
PD6
PD5
PD4
PD3
PD2
PD1
PD0
DDRE
7
6
5
4
3
2
1
0
Address : 0000D1H
PE7
PE6
PE5
PE4
PE3
PE2
PE1
PE0
7
6
5
4
3
2
1
0
PF7
PF6
PF5
PF4
PF3
PF2
PF1
PF0
7
6
5
4
3
2
1
0
Address : 0000D7H


PG5
PG4
PG3
PG2
PG1
PG0
DDRH
7
6
5
4
3
2
1
0
Address : 0000D6H





PH2
PH1
PH0
7
6
5
4
3
2
1
0
Address : 0000D5H


PI5
PI4
PI3
PI2
PI1
PI0
DDRJ
7
6
5
4
3
2
1
0
Address : 0000D4H


PJ5
PJ4
PJ3
PJ2
PJ1
PJ0
DDRK
7
6
5
4
3
2
1
0
Address : 0000DBH
PK7
PK6
PK5
PK4
PK3
PK2
PK1
PK0
DDRL
7
6
5
4
3
2
1
0
Address : 0000DAH
PL7
PL6
PL5
PL4
PL3
PL2
PL1
PL0
DDR8
DDRF
Address : 0000D0H
DDRG
DDRI
Initial value Access
00000000B
Initial value Access
00000000B
W
Initial value Access
00000000B
W
Initial value Access
00000000B
W
Initial value Access
00000000B
W
Initial value Access
- 0000000B
W
Initial value Access
00000000B
R/W
Initial value Access
00000000B
R/W
Initial value Access
00000000B
R/W
Initial value Access
00000000B
R/W
Initial value Access
- - 000000B
R/W
Initial value Access
- - - - - 000B
R/W
Initial value Access
- - 000000B
R/W
Initial value Access
- - 000000B
R/W
Initial value Access
00000000B
R/W
Initial value Access
00000000B
DDR0 to L control input/output direction of the I/O ports handled per bit.
DDR = 0 : Port input
DDR = 1 : Port output
“0” must be written into the empty bit.
46
W
R/W
MB91133/MB91F133
• Pull up Control Register (PCR)
PCR6
7
6
5
4
3
2
1
0
Address : 000631H
P67
P66
P65
P64
P63
P62
P61
P60
PCRC
7
6
5
4
3
2
1
0
Address : 0000C3H
PC7
PC6
PC5
PC4
PC3
PC2
PC1
PC0
PCRD
7
6
5
4
3
2
1
0
Address : 0000C2H
PD7
PD6
PD5
PD4
PD3
PD2
PD1
PD0
7
6
5
4
3
2
1
0






PE1
PE0
7
6
5
4
3
2
1
0





PH2
PH1
PH0
7
6
5
4
3
2
1
0


PI5
PI4
PI3
PI2
PI1
PI0
7
6
5
4
3
2
1
0


PJ5
PJ4
PJ3
PJ2
PJ1
PJ0
PCRE
Address : 0000C1H
PCRH
Address : 0000C6H
PCRI
Address : 0000C5H
PCRJ
Address : 0000C4H
Initial value Access
00000000B
R/W
Initial value Access
00000000B
R/W
Initial value Access
00000000B
R/W
Initial value Access
- - - - - - 00B
R/W
Initial value Access
- - - - - 000B
R/W
Initial value Access
- - 000000B
R/W
Initial value Access
- - 000000B
R/W
PCR6 to J carry out pull-up resistance control of the I/O ports handled.
PCR = 0 : Pull-up resistance turned off
PCR = 1 : Pull-up resistance turned on
• Open-drain Control Register (ODCR)
OCRH
Address : 0000CAH
OCRI
Address : 0000C9H
OCRJ
Address : 0000C8H
7
6
5
4
3
2
1
0





PH2
PH1
PH0
7
6
5
4
3
2
1
0


PI5
PI4
PI3
PI2
PI1
PI0
7
6
5
4
3
2
1
0


PJ5
PJ4
PJ3
PJ2
PJ1
PJ0
Initial value Access
- - - - - 000B
R/W
Initial value Access
- - 000000B
R/W
Initial value Access
- - 000000B
R/W
OCRH to J carry out open-drain control in output mode of the I/O ports handled.
OCR = 0 : Standard output port in output mode
OCR = 1 : Open-drain output port in output mode
This has no meaning in input mode (output Hi-z) .
47
MB91133/MB91F133
• Analog Input Control Register (AICR)
AICK
7
6
5
4
3
2
1
0
Address : 0000CFH
PK7
PK6
PK5
PK4
PK3
PK2
PK1
PK0
AICK controls each pin of the I/O ports handled as follows.
AIC = 0 : Analog input mode
AIC = 1 : Port input mode
Set to “0” when reset.
48
Initial value Access
00000000B
R/W
MB91133/MB91F133
3. 8/16-bit Up/Down Counter / Timer
8/16-bit up/down counter / timer is configured of event input pins × 6, 8-bit up/down counters × 2, 8-bit reload /
compare registers × 2 and their control circuits.
• Characteristics of 8/16-bit Up/Down Counter / Timer
• Counting from (0) d to (256) d is possible using an 8-bit counting register.
(Counting from (0) d to (65535) d is possible in 16-bit × 1 operation mode.)
• 4 types of counting mode can be selected by the count clock
• Selection can be made from two types of internal clock as the count clock in timer mode.
• Detection edge of the external pin input signals can be selected in up/down count mode.
• Phase difference count mode is suited to count encoders such as motors. Turning angle and turning number,
etc., can easily and accurately be counted by separately inputting phase A, B and Z outputs of the encoder.
• Selection can be made from two function types for the ZIN pin (valid for all modes) .
• Compare and reload functions are featured, and each function can be used alone or in combination.
Up/down counting with random width can be carried out using both functions in combination.
• The count direction directly before can be identified by the count direction flag.
• Generation of interruptions in case of compared match, reload (underflow) or overflow and in cases where the
count direction is changed can be controlled separately.
49
MB91133/MB91F133
• Block Diagram
8/16-bit Up/Down Counter / Timer (ch0)
Data bus
8 bit
Reload / Compare Register 0 (RCR0)
CGE1 CGE0 C/GS
ZIN0
RCUT
Edge/level detection
Reload control
UCRE
RLDE
Counter clear
UDCC
8 bit
Up/Down Count Register 0 (UDCR0)
Carry
CES1 CES0
UDFF OVFF
CMS1 CMS0
CITE
AIN0
BIN0
Up/down count
clock selection
Pre-scalar
CLKS
50
Count clock
UDF1 UDF0 CDCF CFIE
CSTR
Interruption output
UDIE
CMPF
MB91133/MB91F133
8/16-bit Up/Down Counter / Timer (ch1)
Data bus
8 bit
Reload / Compare Register 1 (RCR1)
CGE1 CGE0 C/GS
ZIN1
Edge/level detection
UDCC
RCUT
Reload control
UCRE
RLDE
Counter clear
8 bit
Up/Down Count Register 1 (UDCR1)
CMPF
UDFF OVFF
CMS1 CMS0 CES1 CES0 M16E
CITE
Carry
UDIE
Count clock
AIN1
BIN1
Up/down count
clock selection
Pre-scalar
UDF1 UDF0 CDCF CFIE
CSTR
Interruption output
CLKS
51
MB91133/MB91F133
• Register List
31
24 23
16 15
0
RCR0
UDCR1
UDCR0
CCRH0
CCRL0

CSR0
CCRH1
CCRL1

CSR1
Up/down count register ch0 (UDCR0)
bit
7
6
Address : 000087H
D07
D06
5
4
3
2
1
0
D05
D04
D03
D02
D01
D00
Up/down count register ch1 (UDCR1)
bit
15
14
Address : 000086H
D17
D16
13
12
11
10
9
8
D15
D14
D13
D12
D11
D10
Reload compare register ch0 (RCR0)
bit
7
6
Address : 000085H
D07
D06
Reload compare register ch1 (RCR1)
bit
15
14
Address : 000084H
D17
D16
Counter Status register ch0, 1 (CSR0, 1)
bit
7
6
00008BH
Address :
CSTR
CITE
00008FH
5
4
3
2
1
0
D05
D04
D03
D02
D01
D00
13
12
11
10
9
8
D15
D14
D13
D12
D11
D10
5
4
3
2
1
0
UDIE
CMPF
OVFF
UDFF
UDF1
UDF0
4
3
2
1
0
RLDE
UDCC
CGSC
CGE1
CGE0
Counter control register ch0, 1 (CCRL0, 1)
bit
7
6
5
000089H
Address :

CTUT UCRE
00008DH
52
8 7
RCR1
Counter control register ch0 (CCRH0)
bit
15
14
Address : 000088H M16E CDCF
13
12
11
10
9
8
CFIE
CLKS
CMS1
CMS0
CES1
CES0
Counter control register ch1 (CCRH1)
bit
15
14
Address :00008CH

CDCF
13
12
11
10
9
8
CFIE
CLKS
CMS1
CMS0
CES1
CES0
MB91133/MB91F133
4. 16-bit Reload Timer
The 16-bit timer is configured with a 16-bit down counter, 16-bit reload register, pre-scalar to prepare the internal
count clock and control register. Selection can be made from three types of internal clocks (machine clock 2 /
8 / 32 cycles) as the input clock. DMA transfer can be initiated by interruption. The MB91133/MB91F133 features
a 5-channel timer.
• Block Diagram
16
16-bit reload register
8
Reload
RELD
16
16-bit down counter
OUTE
UF
OUTL
2
OUT
CTL.
R - BUS
GATE
INTE
2
IRQ
UF
CSL1
CNTE
Clock selector
CSL0
Re-trigger
2
TRG
IN CTL.
EXCK
φ
φ
φ
21 23 25
Pre-scalar
clear
3
PWM (ch0, ch1)
A/D (ch2)
MOD2
MOD1
MOD0
3
Channel 2TO output of the reload timer is connected to the A/D converter inside the LSI. Thus, A/D conversion
can be started up at the cycle set in the reload register.
53
MB91133/MB91F133
5. PPG Timer
The PPG timer can efficiently output accurate PWM waveforms. The MB91130 series features a 6-channel
PPG timer.
• PPG Timer Characteristics
• Each channel is configured with a 16-bit down counter, 16-bit data register with cycle setting buffer, 16-bit
compare register with duty setting buffer and pin control area.
• Selection can be made from four types of count clocks for 16-bit down counters.
Internal clock φ, φ4, φ16, φ64
• Counter values can be initialized to “FFFFH” by resetting and counter borrowing.
• PWM output is available per channel.
• Register outline
Cycle setting register : Reloading register with buffer
Duty setting register : Compare register with buffer
Transfer from buffer is carried out by counter borrowing.
• Pin control outline
Set to “1” by duty match. (Priority)
Resets to “0” by counter borrowing.
All “L” (or “H”) can simply be output by using the output values fixing mode.
Polarization can also be specified.
• Interruption request can be generated by selecting from the following combinations.
Initiation of this timer
Counter borrow generation (cycle match)
Duty match generation
Counter borrow generation (cycle match) or duty match generation
DMA transfer can be initiated by the above interruption requests.
• Simultaneous initiation of a number of channels can be set by software or other interval timers. Re-start during
operation can also be set.
54
MB91133/MB91F133
• Block Diagram
Overall Block Diagram of PPG Time
16-bit reload timer
ch0
TRG input
PWM timer ch0
PWM0
16-bit reload timer
ch1
TRG input
PWM timer ch1
PWM1
4
TRG input
PWM timer ch2
PWM2
4
TRG input
PWM timer ch3
PWM3
External TRG4
PWM timer ch4
PWM4
External TRG5
PWM timer ch5
PWM5
General control
register 1
(factor selection)
General control
register 2
External TRG0 to 3
55
MB91133/MB91F133
Block Diagram of PPG Timer for 1 Channel
PDUT
PCSR
Pre-scalar
1/1
1/4
1 / 16
1 / 64
CMP
Load
CK
16-bit down counter
Start
Borrow
PPG mask
S
Peripheral system clock
Q
PWM OUTPUT
R
Reverse bit
Enable
TRG input
Edge
detection
Soft trigger
56
Interruption
selection
IRQ
MB91133/MB91F133
• Register list
Address
15
0
GCN1
000000DCH
000000DFH
GCN2
R/W
General control register 1
R/W
General control register 2
000000E0H
PTMR
R
ch0 Timer register
000000E2H
PCSR
W
ch0 Peripheral setting register
000000E4H
PDUT
W
ch0 Duty setting register
R/W
ch0 Control status register
000000E6H
PCNL
PCNH
000000E8H
PTMR
R
ch1 Timer register
000000EAH
PCSR
W
ch1 Peripheral setting register
000000ECH
PDUT
W
ch1 Duty setting register
R/W
ch1 Control status register
000000EEH
PCNH
PCNL
000000F0 H
PTMR
R
ch2 Timer register
000000F2 H
PCSR
W
ch2 Peripheral setting register
000000F4 H
PDUT
W
ch2 Duty setting register
R/W
ch2 Control status register
000000F6 H
PCNL
PCNH
000000F8 H
PTMR
R
ch3 Timer register
000000FAH
PCSR
W
ch3 Peripheral setting register
000000FCH
PDUT
W
ch3 Duty setting register
R/W
ch3 Control status register
000000FEH
PCNH
PCNL
(Continued)
57
MB91133/MB91F133
(Continued)
Address
0
00000100 H
PTMR
R
ch4 Timer register
00000102 H
PCSR
W
ch4 Peripheral setting register
00000104 H
PDUT
W
ch4 Duty setting register
R/W
ch4 Control status register
00000106 H
PCNL
PCNH
00000108 H
PTMR
R
ch5 Timer register
0000010AH
PCSR
W
ch5 Peripheral setting register
0000010CH
PDUT
W
ch5 Duty setting register
R/W
ch5 Control status register
0000010EH
58
15
PCNH
PCNL
MB91133/MB91F133
6. Multifunction Timer
The multifunction timer unit is configured of a 16-bit freerun timer × 1, 16-bit output compare × 8, 16-bit input
capture × 4, 16-bit PPG timer × 6 ch and waveform generation area modules. 12 independent waveform outputs
based on a 16-bit free-run timer are possible using this function and measurement of input pulse width and
external clock cycle is also possible.
• Multifunction Timer Configuration
• 16-bit free-run timer ( × 1)
The 16-bit free-run timer consists of a 16-bit up counter, control register, 16-bit compare clear register and
pre-scalar. Output values of this counter are used as the base timer for output compare and input capture.
• Counter operation clocks can be selected from six types.
Six types of internal clocks (φ2, φ4, φ8, φ16, φ32, φ64)
φ : Machine clock
• Interruption can be generated by overflow of the counter value and a compared match with compare
clear register. (Mode setting is required for a compared match.)
• Counter value can be initialized to “0000H” by a compared match with the reset, software clear or the
compare clear register.
• Output compare ( × 8)
Output compare is configured of 16-bit compare register × 8, latch for compare output and control register.
Interruption can be generated as well as reversing output level when the 16-bit free-run timer value and compare
register value match.
• 8 compare registers can be operated independently. Output pins and interruption flags support each
compare register.
• Output pins can be controlled by pairing two compare registers. Output pins are reversed using two
compare registers.
• Initial value of each output pin can be set.
• Interruption can be generated by matching compare.
• Input capture ( × 4)
Input capture is configured with four independent external input pins , supported capture and control register.
16-bit free-run timer value is held in the capture register by detecting the random edge of signals that are input
by the external input pin, and interruption can simultaneously be generated.
• Valid edges (rising edge, falling edge, both edges) of external input signals can be selected.
• Four input captures can be operated independently.
• Interruption can be generated by the valid edges of external input signals.
• 16-bit PPG timer ( × 6)
Refer to PPG timer
59
MB91133/MB91F133
• Waveform Generation Area
The waveform generation area is configured with 8-bit timer × 3, 8-bit reload register × 3, timer control register
× 3 and 8-bit waveform control register. This control circuit controls the waveform of the 16-bit PPG timer and
real-time output, and DC chopper output and non-overlapping 3-phase waveform output to be used for inverter
control are possible.
• Non-overlapping pulse output of the PPG timer is possible by setting dead time of the 8-bit timer (dead
time timer function) .
• Real timer output is operated by the 2-channel mode and non-overlapping output of the waveform is
possible by setting the dead time of the 8-bit timer (dead time timer function) .
• Operation of PPG timer can easily be started/stopped by generating a GATE signal for the PPG timer
operation through match detection of real-time output compare (GATE function).
• The 8-bit timer is operated by match detection of real-time output compare, and operation of the PPG timer
can easily be started/stopped by generating a GATE signal for the PPG timer until the 8-bit timer is stopped
(GATE function) .
• Pin output can be forcibly controlled by input to the DTTI pin. Pins can be controlled externally even if
oscillations stop due to lack of clocks for inputs to this pin. (Each pin level can be set by the program .)
If this function is used, the port should be set to output (DDR = 1) and the output value should be
described in the PDR beforehand.
60
MB91133/MB91F133
• Block Diagram
Block Diagram of PPG Timer for 1 Channel
φ
Interruption
IVF
IVFE
STOP
MODE
SCLR
CLK2
CLK1
CLK0
Cycle device
Clock
16-bit free-run timer
16-bit compare clear register
(Ch. 6 compare register)
MS13 ∼ 0
Compare register 0/2/4
Compare circuit
Compare register 1/3/5
Interruption
Compare circuit
ICLR
ICRE
R-BUS
T
Q
RT0/2/4
To waveform
generation area
T
Q
RT1/3/5
To waveform
generation area
CMOD
Compare circuit
IOP1
IOP0
IOE1
IOE0
Interruption
Interruption
IN 0/2
Edge detection
Capture data register 0/2
EG11
Capture data register 1/3
EG10
EG01
Edge detection
ICP0
ICP1
ICE0
EG00
IN 1/3
ICE1
Interruption
Interruption
61
MB91133/MB91F133
Block Diagram of Waveform Generation Area
φ
DCK2
DCK1
DCK0
TMD1
TMD0
NRSL
DTIL
DTIE
DTTI control circuit
DTTI
Cycle device
GATE 0/1
Clock
RT0
Waveform
generation area
TO0
TO1
RT1
8-bit timer
Compare
circuit
8-bit timer register 0
Selector
Selector
Dead time
generation
RTO0/U
RTO1/X
U
X
R−BUS
GATE 2/3
Waveform
generation area
RT2
TO2
TO3
RT3
8-bit timer
Compare
circuit
8-bit timer register 1
Selector
Selector
Dead time
generation
RTO2/V
RTO3/Y
V
Y
GATE 4/5
Waveform
generation area
RT4
TO4
TO5
RT5
8-bit timer
Compare
circuit
8-bit timer register 2
62
Selector
Selector
Dead time
generation
RTO4/W
RTO5/Z
W
Z
MB91133/MB91F133
• Registers List
Address
15
8 7
000044H to 4BH
0
(R)
IPCP
00004DH, 4FH
ICS
(R/W)
000054H to 63H
OCCP
(R/W)
000064H to 6BH
OCS
(R/W)
00006CH, 6DH
TCDT
(R/W)
00006EH, 6FH
TCCS
(R/W)
0000ACH, AEH
B2H
0000ADH, AFH
B3H
0000B1H
(R/W)
DTCR
TMRR
(R/W)
STGCR
(R/W)
63
MB91133/MB91F133
7. External Interruption
The external interruption control area is the block that controls the external interruption requests input in INT0
to INT23. The level of request to be detected can be selected from “H”, “L”, “Rising edge” or “ Falling edge”.
• Block diagram
R-BUS
24
Interruption
requests
Interruption permission register
24
Gate
24
Factor F/F
24
Edge detection circuit
INT0 to INT23
Interruption factor register
48
Request level setting register
• Register List
External interruption permission register (ENIR)
15
14
13
bit
ER7
ER6
12
11
10
9
8
ER4
ER3
ER2
ER1
ER0
12
11
10
9
8
ER5
ER4
ER3
ER2
ER1
ER0
5
4
3
2
1
0
LB2
LA2
LB1
LA1
LB0
LA0
ER5
External interruption factor register (EIRR)
15
14
13
bit
ER7
ER6
Request level setting register (ELVR)
7
6
bit
LB3
bit
LA3
15
14
13
12
11
10
9
8
LB7
LA7
LB6
LA6
LB5
LA5
LB4
LA4
There are three sets of the above registers (for 8 channels) for a total of 24 channels.
64
MB91133/MB91F133
8. Delay Interruption Module
The delay interruption module generates interruptions for task switching. Interruption requests to the CPU can
be generated / cancelled using software with this module.
• Block Diagram
Refer to “9.(2) Block Diagram of Interruption Controller” for the block diagram of the delay interruption generation
area.
• Register List
Address : 00000430H
bit 7
6
5
4
3
2
1
0







DLYI
DICR
R/W
65
MB91133/MB91F133
9. Interruption Controller
The interruption controller carries out interruption reception and arbitration.
• Hardware configuration of the interruption controller
This module consists of the following items.
• ICR register
• Interruption priority judgement circuit
• Interruption level, interruption number (vector) generation area
• Cancellation request generation area for HOLD request
• Major interruption controller functions
This module has the following functions.
• Detection of interruption requests
• Priority grade judgement (depending on the level and number)
• Transferring interruption level of factors for the judgement results (to CPU)
• Transferring interruption number of factors for the judgement results (to CPU)
• Recovery instruction from stop mode by generating interruption
• Cancellation of HOLD request to the bus master
• Resetting Interruption Factors
There are restrictions between RETI instructions and those for resetting interruption factors in the interruption
routine.
66
MB91133/MB91F133
• Block Diagram
INT0
IM
Priority grade judgement
OR
5
NMI
LEVEL4 to 0
NMI processing
4
LEVEL
judgement
ICR00
RI00
VECTOR
judgement
6
Generation
of
LEVEL /
VECTOR
HLDREQ
(Holding
request)
HLDCAN
VCT5 to 0
ICR47
RI47
(DLYIRQ)
DLYI
R-BUS
Note : DLYI shown in the figure indicates delay interruption area. (Refer to the chapter on the delay interruption
module for details.)
INTO is the wake-up signal to the clock control area in case of sleep or stop.
HLDCAN is the bus vacation request signal to bus masters other than the CPU.
There is no NMI function in this model.
67
MB91133/MB91F133
• Register List
bit 7
6
5
4
3
2
1
0
Address : 00000400H




ICR3
ICR2
ICR1
ICR0
ICR00
Address : 00000401H




ICR3
ICR2
ICR1
ICR0
ICR01
Address : 00000402H




ICR3
ICR2
ICR1
ICR0
ICR02
Address : 00000403H




ICR3
ICR2
ICR1
ICR0
ICR03
Address : 00000404H




ICR3
ICR2
ICR1
ICR0
ICR04
Address : 00000405H




ICR3
ICR2
ICR1
ICR0
ICR05
Address : 00000406H




ICR3
ICR2
ICR1
ICR0
ICR06
Address : 00000407H




ICR3
ICR2
ICR1
ICR0
ICR07
Address : 00000408H




ICR3
ICR2
ICR1
ICR0
ICR08
Address : 00000409H




ICR3
ICR2
ICR1
ICR0
ICR09
Address : 0000040AH




ICR3
ICR2
ICR1
ICR0
ICR10
Address : 0000040BH




ICR3
ICR2
ICR1
ICR0
ICR11
Address : 0000040CH




ICR3
ICR2
ICR1
ICR0
ICR12
Address : 0000040DH




ICR3
ICR2
ICR1
ICR0
ICR13
Address : 0000040EH




ICR3
ICR2
ICR1
ICR0
ICR14
Address : 0000040FH




ICR3
ICR2
ICR1
ICR0
ICR15
Address : 00000410H




ICR3
ICR2
ICR1
ICR0
ICR16
Address : 00000411H




ICR3
ICR2
ICR1
ICR0
ICR17
Address : 00000412H




ICR3
ICR2
ICR1
ICR0
ICR18
Address : 00000413H




ICR3
ICR2
ICR1
ICR0
ICR19
Address : 00000414H




ICR3
ICR2
ICR1
ICR0
ICR20
Address : 00000415H




ICR3
ICR2
ICR1
ICR0
ICR21
Address : 00000416H




ICR3
ICR2
ICR1
ICR0
ICR22
Address : 00000417H




ICR3
ICR2
ICR1
ICR0
ICR23
Address : 00000418H




ICR3
ICR2
ICR1
ICR0
ICR24
Address : 00000419H




ICR3
ICR2
ICR1
ICR0
ICR25
Address : 0000041AH




ICR3
ICR2
ICR1
ICR0
ICR26
Address : 0000041BH




ICR3
ICR2
ICR1
ICR0
ICR27
Address : 0000041CH




ICR3
ICR2
ICR1
ICR0
ICR28
Address : 0000041DH




ICR3
ICR2
ICR1
ICR0
ICR29
Address : 0000041EH




ICR3
ICR2
ICR1
ICR0
ICR30
Address : 0000041FH




ICR3
ICR2
ICR1
ICR0
ICR31
R/W
R/W
R/W
R/W
(Continued)
68
MB91133/MB91F133
(Continued)
bit 7
6
5
4
3
2
1
0
Address : 00000420H




ICR3
ICR2
ICR1
ICR0
ICR32
Address : 00000421H




ICR3
ICR2
ICR1
ICR0
ICR33
Address : 00000422H




ICR3
ICR2
ICR1
ICR0
ICR34
Address : 00000423H




ICR3
ICR2
ICR1
ICR0
ICR35
Address : 00000424H




ICR3
ICR2
ICR1
ICR0
ICR36
Address : 00000425H




ICR3
ICR2
ICR1
ICR0
ICR37
Address : 00000426H




ICR3
ICR2
ICR1
ICR0
ICR38
Address : 00000427H




ICR3
ICR2
ICR1
ICR0
ICR39
Address : 00000428H




ICR3
ICR2
ICR1
ICR0
ICR40
Address : 00000429H




ICR3
ICR2
ICR1
ICR0
ICR41
Address : 0000042AH




ICR3
ICR2
ICR1
ICR0
ICR42
Address : 0000042BH




ICR3
ICR2
ICR1
ICR0
ICR43
Address : 0000042CH




ICR3
ICR2
ICR1
ICR0
ICR44
Address : 0000042DH




ICR3
ICR2
ICR1
ICR0
ICR45
Address : 0000042EH




ICR3
ICR2
ICR1
ICR0
ICR46
Address : 0000042FH




ICR3
ICR2
ICR1
ICR0
ICR47
R/W
R/W
R/W
R/W
LVL3
LVL2
LVL1
LVL0
R/W
R/W
R/W
R/W
Address : 00000431H




HRCL
69
MB91133/MB91F133
10. Clock Generation Area (low power consumption mechanism)
Clock generation area is a module with the following functions.
• CPU clock generation (including gear function)
• Peripheral clock generation (including gear function)
• Reset generation and holding factors
• Standby function (including hardware standby)
• PLL (Phase Locked Loop) is built in
• Register list
Address
70
7
0
Reset factor / watchdog cycle control register
000480H
RSRR/WTCR
000481H
STCR
Standby control register
000482H
PDRR
DMA request blocking register
000483H
CTBR
Time base timer clear register
000484H
GCR
Gear control register
000485H
WPR
Watchdog reset generation postponement register
000488H
PCTR
PLL / 32-K clock control register
MB91133/MB91F133
• Block diagram
[ Gear control area ]
GCR register
CPU gear
Peripheral
gear
X0A
X1A
Oscillation
circuit
1/2
X0
X1
Oscillation
circuit
PLL
Internal clock
generation
circuit
M
P
X
CPU clock
Internal
bus clock
Internal
peripheral clock
32-kHz selection circuit
[ Stop/sleep control area ]
Internal interruption
Internal reset
STCR register
STOP status
SLEEP status
CPU hold request
DMA request
PDRR register
Status
transfer
control circuit
Reset
generation
F/F
Internal reset
Power on
detection circuit
[ Reset factor circuit ]
VCC3
R
GND
RSRR register
RST pin
[ Watchdog control area ]
WPP register
Watchdog F/F
Count clock
CTBR register
Time base timer
71
MB91133/MB91F133
11. 8-/10-bit A/D Converter
The 8-/10-bit A/D converter features functions that convert analog input voltages to 10- or 8-bit digital values
using the RC sequential comparison conversion method. The input signal is selected from 8-channel analog
input pins and three types of conversion initiation can be selected from software, internal clock, or external pin
trigger.
• characteristics of 8-/10-bit A/D converter
The A/D conversion function for converting analog voltages (input voltages) input into the analog input pins to
digital values has the following characteristics.
• Conversion time is minimum 5.0 µs (including sampling time when machine clock is 33 MHz) .
• Conversion method is RC sequential comparison conversion method with sample holding circuit.
• 10- or 8-bit resolution can be selected.
• Analog input pin can be selected from 8 channels using the program.
• interruption request can be generated when A/D conversion ends.
• Data is not lost even during continuous conversion as conversion data protection function works while interruptions are permitted.
• Initiation factors for conversion can be selected from software, 16-bit reload timer 2 (rising edge) , or external
pin trigger (L level detection) .
There are three types of conversion modes.
Conversion Modes
Single conversion mode
Converts the specified channel (1 channel Converts a series of channels (up to 8
only) once and ends.
channels can be specified) once and ends.
Consecutive
conversion mode
Repeatedly converts the specified channel Repeatedly converts a series of channels
(1 channel only) .
(up to 8 channels can be specified) .
Stop conversion mode
72
Table 13.1-1 Conversion Modes of 8-/10-bit A/D Converter
Single Conversion Operation
Scan Conversion Operation
Suspends after converting the specified
channel (1 channel only) once and waits
until the next one is initiated.
Converts a series of channels (up to 8
channels can be specified) but is suspended between each channel conversion and
waits until the next one is initiated.
MB91133/MB91F133
• Block Diagram of 8-/10-bit A/D Converter
The 8-/10-bit A/D converter is configured with the following 9 blocks.
• A/D control status register (ADCS1, 2)
• A/D data register (ADCR)
• Clock selector (input clock selector to initiate A/D conversion)
• Decoder
• Analog channel selector
• Sample holding circuit
• D/A converter
• Comparator
• Control circuit
• Block Diagram
AVSS AVR±
AVSS
MP
D/A converter
AN0
AN1
AN2
AN3
AN4
AN5
AN6
AN7
Input
circuit
Sequential
comparison register
R - BUS
Comparator
Sample and
holding circuit
Data register
ADCR
Decoder
A/D control register 1
A/D control register 2
16-bit reload timer 2
ADCS1, 2
External pin trigger
Operation clock
φ
Pre-scalar
• Register List
15
14
13
12
11
10
9
8
7
0000CFH
00003AH
000038 H
6
5
4
3
2
1
0
AICK
ADCS0
ADCS1
ADCR
73
MB91133/MB91F133
12. 8-bit D/A Converter
The 8-bit D/A converter is an R-2R type D/A converter with 8-bit resolution.
• Characteristics of the 8-bit D/A converter
The MB81130 series features a 3-channel D/A converter and output control can be carried out individually by
the D/A control register.
• Block Diagram of 8-bit D/A Converter
The 8-bit D/A converter is configured with the following three blocks.
• 8-bit resistance ladder
• Data register
• Control register
• Block Diagram
R − BUS
DA27 to DA20
DA17 to DA10
DAVC
DAVC
DAVC
DA27
DA17
DA07
DA20
DA10
DA00
DAE
Standby control
DA output
74
DA07 to DA00
DAE
Standby control
DA output
DAE
Standby control
DA output
MB91133/MB91F133
• 8-bit D/A Converter Pins
D/A converter pins are dedicated pins.
• Registers of 8-bit D/A Converter
The 8-bit D/A converter has the following two registers.
D/A control register (DACR0, 1, 2)
D/A data register (DADR2, 1, 0)
• Register list
D/A converter data register 0
bit
7
DADR0
DA07
00000ABH
D/A converter data register 1
bit
15
DADR1
DA17
00000AAH
D/A converter data register 2
bit
23
DADR2
DA27
00000A9H
6
5
4
3
2
1
0
DA06
DA05
DA04
DA03
DA02
DA01
DA00
14
13
12
11
10
9
8
DA16
DA15
DA14
DA13
DA12
DA11
DA10
22
21
20
19
18
17
16
DA26
DA25
DA24
DA23
DA22
DA21
DA20
7
6
5
4
3
2
1
0







DAE0
15
14
13
12
11
10
9
8







DAE1
23
22
21
20
19
18
17
16







DAE2
D/A control register 0
bit
DACR0
00000A7H
D/A control register 1
bit
DACR1
00000A6H
D/A control register 2
bit
DACR2
00000A5H
75
MB91133/MB91F133
13. 4-bit Level Comparator
The 4-bit level comparator is the module that compares input levels (large/small) and compares the size of the
analog input voltage with 4-bit digital values.
• Functions of the 4-bit level comparator
Compares analog voltage that has been input to the analog input pins (input voltage) with 4-bit digital value and
has the following characteristics.
• Conversion time is minimum 1 µs (including sampling time) .
• Sampling time is minimum 0.5 µs.
• Interruption requests can be generated when analog comparison ends.
• Interruption of 4-bit level comparator
Interruption
number
#61 (3DH)
Table 15.1-1 Interruption and DMAC of 4-bit level comparator
Interruption control register
TBR default
Offset
address
Register name
Address
ICR45
× : Initiation is impossible
76
00042DH
308H
000FFF08H
DMAC
×
MB91133/MB91F133
• Block Diagram of 4-bit Level Comparator
The 4-bit level comparator is configured with the following three blocks.
• Comparator
• 4-bit resistance ladder
• Control register
• Block diagram
AVCC
AVR±
AVSS
4-bit D/A (resistance ladder)
RD3 - 0
Sample &
holding circuit
CPLV
INT
INTE
CPEN
FR30 R - BUS
Comparator
AN7
Interruption
Reload timer
Operation clock
φ
77
MB91133/MB91F133
• Registers of 4-bit Lev el Comparator
• Register list
bit 31
bit 24 bit 23
0000-0018H
Control register (LVLC)
bit
0000018H
78
bit 16
LVLC
31
30
29
28
27
26
25
24
RD3
RD2
RD1
RD0
CPLV
INT
INTE
CPEN
R/W
(X)
R/W
(X)
R/W
(X)
R/W
(X)
R/W
(0)
R/W
(0)
R/W
(0)
R/W
(0)
Attribute
Initial value
MB91133/MB91F133
14. UART
UART is the general-purpose serial data communications interface to carry out synchronous or asynchronous
communication (start-stop synchronization) with external systems. It has a master/slave-type communications
function (multiprocessor mode: supporting only master side) as well as normal bi-directional communications
function (normal mode).
• UART Functions
UART is the general-purpose serial data communications interface that sends and receives serial data to/from
other CPUs and peripheral equipment, and has functions shown in Table 16.1-1.
Table 16.1-1 UART Functions
Functions
Data buffer
Transfer mode
Baud rate
Data length
Signal method
Reception error detection
Interruption request
Master/slave-type
communications function
(Multiprocessor mode)
Full-duplex double buffer
• Clock synchronous (without start-stop bit)
• Clock asynchronous (start-stop cycle)
• Dedicated baud rate generator is available. Can be selected from 8 types.
• External clock input is possible.
• Internal clock (Internal clocks that are provided from 16-bit reload timer supporting each channel can be used.)
• 7-bit (in case of asynchronous normal mode only)
• 8-bit
Non Return to Zero (NRZ) method
• Framing error
• Overrun error
• Parity error (impossible in case of multiprocessor mode)
• Reception interruption (reception completion, reception error detection)
• Transmission interruption (transmission completion)
Communication between 1 (master) and n (slaves) is possible
(Only supports master side)
Note : Start / stop bits are not added by UART and only data is transferred.
Operations mode
0
1
Table 16.1-2 UART Operations Mode
Data length
Synchronization
method
Without parity
With parity
Normal mode
Multiprocessor mode
2 Normal mode
 : Setting is impossible
7-bit or 8-bit
Asynchronous
8 + 1*

Asynchronous
8

Synchronous
1
Stop bit length
1-bit or 2-bit *2
N/A
*1 : “ + 1” is address / data selection bit (A/D) to be used to control communications.
*2 : 1-bit only can be detected for stop bit in case of reception.
79
MB91133/MB91F133
• UART Block Diagram
UART is configured with the following 11 blocks.
• Clock selector
• Mode register (SMR0 to 4)
• Reception control circuit
• Control register (SCR0 to 4)
• Transmission control circuit
• Status register (SSR0 to 4)
• Reception status judgement circuit
• Input data register (SIDR0 to 4)
• Shift register for reception
• Output data register (SODR0 to 4)
• Sift register for transmission
• Block Diagram
Control bus
Reception
interruption
signals
#26 to 30 *
Dedicated baud rate
generator
16-bit reload timer
Reception
interruption
signals
#31 to 35 *
Transmission
clock
Clock
selector
Reception clock
Pin
Reception
control circuit
Transmission
control circuit
Start bit
detection circuit
Transmission
start circuit
Reception bit
counter
Transmission bit
counter
Reception parity
counter
Transmission parity
counter
Shift register
for reception
Shift register
for transmission
<SCK0 to SCK4>
<SOT0 to SOT4 >
Pin
<SIN0 to SIN4 >
Pin
Reception status
judgement circuit
SIDR0 ∼ 4
Reception
ends
SODR0 ∼ 4
Transmission starts
Reception error
Generation signal
(to CPU)
Internal data bus
SMR0 to 4
registers
MD1
MD0
CS2
CS1
CS0
SCKE
SOE
* : Interruption number
80
SCR0 to 4
registers
PEN
P
SBL
CL
A/D
REC
RXE
TXE
SSR0 to 4
registers
PE
ORE
FRE
RDRF
TDRE
BDS
RIE
TIE
MB91133/MB91F133
• Block Diagram of UART Pins
Data bus
Resource input
0
1
PDR read
pin
0
PDR
Resource output
1
Resource output
permission
DDR
ODCR
PCR
PDR : Port Data Register
DDR : Data Direction Register
ODCR : Open-drain Control Register
PCR : Pull-up Control Register
• Register List
Address
ch0 : 0000_001EH,
ch1 : 0000_0022H,
ch2 : 0000_0026H,
ch3 : 0000_0072H,
ch4 : 0000_0076H,
ch0 : 0000_001CH,
ch1 : 0000_0020H,
ch2 : 0000_0024H,
ch3 : 0000_0070H,
ch4 : 0000_0074H,
ch0 : 0000_007AH
ch1 : 0000_0078H
ch2 : 0000_007EH
ch3 : 0000_007CH
ch4 : 0000_0082H
bit 15
1FH
23H
27H
73H
77H
1DH
21H
25H
71H
75H
bit 8
bit 7
bit 0
Control register
(SCR)
Mode register
(SMR)
Status register
(SSR)
Input/output data register
(SIDR/SODR)
Communications pre-scalar control register
(CDCR)
Vacant
81
MB91133/MB91F133
15. DMA Controller
The DMA controller is the built-in module of the MB91130 series that carrie out direct memory access (DMA)
transfers.
•
•
•
•
•
•
•
•
Characteristics of the DMA Controller
8 channels
3 transfer mode types : single/block transfer, burst transfer, continuous transfer
Transfer between overall address areas
Maximum 65,536 transfers
Interruption function when transfer ends
Increase/decrease in transfer addresses can be selected using software
3 external transfer request input/output pins and 3 external transfer end output pins
• Block Diagram
DREQ0 to DREQ2
3
Edge / level
detection circuit
3
3
3
Sequencer
DACK0 to DACK2
EOP0 to EOP2
8
Interruption request
Built-in resource
transfer request
5
Data buffer
Switcher
DACSR
DATCR
Mode
BLK DEC
BLK
DMACT
INC / DEC
SADR
DADR
82
Data bus
DPDP
MB91133/MB91F133
• Register List
(In DMAC : DMAC internal registers)
31
0
00000200H
DPDP
00000204H
DACSR
00000208H
DATCR
(On RAM : DMA descriptors)
bit 31
DPDP + 0H
DPDP + 0CH
DPDP + 54H
bit 0
DMA
ch0
Descriptor
DMA
ch1
Descriptor
DMA
ch7
Descriptor
83
MB91133/MB91F133
16. Bit Search Module
The bit search module searches for 0, 1 or change points on data that has been written in the input register, and
returns the detected bit position.
• Block Diagram
D-BUS
Input latch
Address
decoder
Detection
mode
Changing to 1 detection data
Bit search circuit
Detection results
• Register List
31
84
0
Address : 000003F0H
BSD0
Data register for 0 detection
Address : 000003F4H
BSD1
Data register for 1 detection
Address : 000003F8H
BSDC
Data register for change point detection
Address : 000003FCH
BSRR
Detection results register
MB91133/MB91F133
17. FLASH Memory
The MB91FV130 / MB91F133 have a 254-KB (2 Mbit) capacity and feature a FLASH memory that can write
each half-word (16 bits) using the FR-CPU, delete individual sectors sector and delete groups of sectors together
using a single 3-V power source.
• Outline of FLASH Memory
This is a built-in 3-V 254-KB FLASH memory. This FLASH memory is the same as our 2-Mbit (256 K × 8 / 128
K × 16) FLASH memory MBM29LV400C and writing is possible from outside the device using a ROM writer. If
used as a built-in ROM of the FR-CPU, as well as having an equivalent function to the MBM29LV400C, instructions / data can be read per word (32 bits) and high-speed operation of the device can be realized.
Refer to the MBM29LV400C data sheet as well as this manual.
The following functions can be realised in MB91FV130 / MB91F133 by combining the FLASH memory macro
and FR-CPU interface circuits.
• Functioning as memory for CPU program / data storage
Access is possible with 32-bit bus width when used as ROM
Reading / writing and erasing (automatic program algorithm *) are possible using CPU
• MBM29LV400C-equivalent function of single FLASH memory products
Reading / writing and erasing (automatic program algorithm *) are possible using ROM writer
A case where this FLASH memory is used from FR-CPU is described in this section.
Refer to the ROM writer manual separately for details if this FLASH memory is used from ROM writer.
* : Automatic program algorithm = Embedded Algorithm TM
Embedded Algorithm TM is the trademark of Advanced Micro Device.
• Block Diagram
Rising edge detection
Control signal
generation
RDY/BUSY
RESET
BYTE
OE
FLASH memory
2 Mbit (254 K × 8/127 K × 16)
WE
INTE
RDYINT
RDY
WE
Bus control signal
Interruption request
CE
FA18 - 0
Address buffer
CA18 - 0
DI15 - 0
DO31 - 0
Data buffer
CD31 - 0
FR-C bus (instruction / data)
85
MB91133/MB91F133
• Memory Map
FLASH memory mode and CPU mode for address mapping of FLASH memory are different. Mapping under
each mode is shown as follows.
• Memory map in FLASH memory mode
0FFFFFH
SA9
SA8
SA7
2 M-FLASH
Memory image
SA6
SA5
SA4
SA3
0C0000H
SA2
SA1
SA0
( SAn : sector address n )
010000H
000000H
• Memory map in CPU memory mode
0FFFFFH
0FFFFFH
SA4
SA9
SA3
SA8
SA2
SA7
SA1
SA6
SA0
SA5
0F8000H
0F4000H
FLASH memory area
0F0000H
0E0000H
0C0800H
RAM area
2 KByte
0C0000H
( SAn : sector address n )
0007C0H
Status register
0C0800H
000000H
0C0000H
86
CPU mode
MB91133/MB91F133
• Sector address table
Sector Address
Address Area
Position of bit
handled
Sector Capacity
SA5
000C0802, 3h to 000DFFFE, Fh (LSB side 16 bit)
bit 15 to 0
63 Kbyte
SA6
000E0002, 3h to 000EFFFE, Fh (LSB side 16 bit)
bit 15 to 0
32 Kbyte
SA7
000F0002, 3h to 000F3FFE, Fh (LSB side 16 bit)
bit 15 to 0
8 Kbyte
SA8
000F4002, 3h to 000F7FFE, Fh (LSB side 16 bit)
bit 15 to 0
8 Kbyte
SA9
000F8002, 3h to 000FFFFE, Fh (LSB side 16 bit)
bit 15 to 0
16 Kbyte
SA0
000C0800, 1h to 000DFFFC, Dh (MSB side 16 bit)
bit 31 to 16
63 Kbyte
SA1
000E0000, 1h to 000EFFFC, Dh (MSB side 16 bit)
bit 31 to 16
32 Kbyte
SA2
000F0000, 1h to 000F3FFC, Dh (MSB side 16 bit)
bit 31 to 16
8 Kbyte
SA3
000F4000, 1h to 000F7FFC, Dh (MSB side 16 bit)
bit 31 to 16
8 Kbyte
SA4
000F8000, 1h to 000FFFFC, Dh (MSB side 16 bit)
bit 31 to 16
16 Kbyte
• Registers of FLASH Memory
There are two types of FLASH memory registers, namely status register (FLCL) and wait register (FWTC).
• Status Register (FLCR) (CPU mode)
This register indicates the operation status of the FLASH memory. It controls interruption to the CPU and
writing to the FLASH memory.
Access is possible only in CPU mode. This register must not be accessed under Read / Modify / Write
instructions.
0007C0H
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
INTE
RDYINT
WE
RDY



LPM
R/W
(0)
R/W
(0)
R/W
(0)
R
(X)

(X)

(X)

(X)
R/W
(0)
• Wait Register ( FWTC)
Carries out wait control of the FLASH memory in CPU mode. Also, controls access to high-speed reading
(33MHz) of FLASH memory. Configuration of Wait Register (FWTC) is as follows :
0007C4H
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0





FACH
WTC1
WTC0

()

()

()

()
W
(0)
R/W
(0)
R/W
(0)

()
Note : FACH bit should be set to 1 or WTC1/0 should be set to 01b to operate machine clocks of CPUs exceeding
25 MHz.
87
MB91133/MB91F133
■ ELECTRICAL CHARACTERISTICS
1. Absolute Maximum Ratings
Parameter
(VSS = AVSS = 0.0 V)
Symbol
Rating
Min.
Max.
Unit
Remarks
Power voltage
VCC5
VSS − 0.3
VSS + 6.5
V
Power voltage
VCC3
VSS − 0.3
VSS + 3.8
V
Analog power voltage
AVCC
VSS − 0.3
VSS + 6.5
V
*1
Standard analog voltage
AVRH
VSS − 0.3
VSS + 6.5
V
*1
Input voltage
VI5
VSS − 0.3
VCC5 + 0.3
V
Input voltage
VI3
VSS − 0.3
VCC3 + 0.3
V
Analog pin input voltage
VIA
VSS − 0.3
AVCC + 0.3
V
Output voltage
VO
VSS − 0.3
VCC5 + 0.3
V
Maximum “L” level output current
IOL

10
mA
*2
Average “L” level output current
IOLAV

4
mA
*3
Maximum total “L” level output current
ΣIOL

100
mA
ΣIOLAV

50
mA
*4
IOH

−10
mA
*2
Average “H” level output current
IOHAV

−4
mA
*3
Maximum total “H” level output current
ΣIOH

−50
mA
ΣIOHAV

−20
mA
PD

500
mW
Tstg
−55
+150
°C
Average “L” level total output current
Maximum “H” level output current
Average “H” level total output current
Electricity consumption
Storage temperature
X0, X1, X0A, X01A
*4
*1 : Care must be taken that this does not exceed VCC5 + 0.3 V when the power is turned on. Also, care must be
taken that AVCC does not exceed VCC5 when the power is turned on. AVCC should be set at the same electrical
potential as VCC5.
*2 : Peak value of the pin concerned is regulated as the maximum output current.
*3 : Average current within 100 ms flowing in the pin concerned is regulated as the average output current.
*4 : Average current within 100 ms flowing in all pins concerned is regulated as the average total output current.
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
88
MB91133/MB91F133
2. Recommended Operating Conditions
Parameter
Power voltage
Symbol
Common
VCC5
EVA
FLASH
VCC3
MASK
ROM
VCC3
(VSS = AVSS = 0.0 V)
Value
Unit
Remarks
Min.
Max.
4.5
5.5
3.0
3.6
3.0
3.6
2.7
3.6
V
Under normal operation
2.7
3.6
V
RAM status kept in the case of stop
V
V
Under normal operation
Under normal operation
RAM status kept in the case of stop
Analog power voltage
AVCC
VSS + 4.5
VSS + 5.5
V
Standard analog voltage
AVRH
AVSS − 0.3
AVCC
V
TA
0
+70
°C
In external ROM external bus /
internal ROM external bus modes
TA
−40
+70
°C
In single-chip mode
Operating temperature
WARNING: The recommended operating conditions are required in order to ensure the normal operation of the
semiconductor device. All of the device’s electrical characteristics are warranted when the device is
operated within these ranges.
Always use semiconductor devices within their recommended operating condition ranges. Operation
outside these ranges may adversely affect reliability and could result in device failure.
No warranty is made with respect to uses, operating conditions, or combinations not represented on
the data sheet. Users considering application outside the listed conditions are advised to contact their
FUJITSU representatives beforehand.
89
MB91133/MB91F133
3. DC Characteristics
(MASK Model VCC5 = AVCC = DAVC = 5.0 V ± 10%, VCC3 = 2.7 V to 3.6 V, VSS = AVSS = 0 V, TA = −40 °C to +70 °C)
(FLASH Model VCC5 = AVCC = DAVC = 5.0 V ± 10%, VCC3 = 3.0 V to 3.6 V, VSS = AVSS = 0 V, TA = −40 °C to +70 °C)
Value
ReSymPin name
Conditions
Unit
Parameter
marks
bol
Min.
Typ.
Max.
“H” level input
voltage
“L” level input
voltage
VIH
Input excluding
following (*1)

0.7 VCC5

VCC5 + 0.3
V
VIHS
*1 Hysteresis
input pin

VCC5 − 0.4

VCC5 + 0.3
V
VIL
Input excluding
following (*1)

VSS − 0.3

0.2 VCC5
V
VILS
*1 Hysteresis
input pin

VSS − 0.3

VSS + 0.4
V
“H” level output
voltage
VOH

VCC5 = 5.0 V,
IOH = −4.0 mA
2.6


V
“L” level output
voltage
VOL

VCC5 = 5.0 V,
IOL = 4.0 mA


0.6
V
ILI

VCC5 = 5.0 V,
VSS < VI < VDD
−5

5
µA

50

kΩ
Input leak
current
Pull up
RPULL
resistance value
RST
ICC5
VCC5
VCC5 = 5.0 V

15
20
mA
ICC3
VCC3
VCC3 = 3.0 V

50
100
mA
ICCS5
VCC5
VCC5 = 5.0 V

15
20
mA
ICCS3
VCC3
VCC3 = 3.0 V

24
85
mA
ICCH5
VCC5
VCC5 = 5.0 V,
TA = 25 °C

10
100
µA
ICCH3
VCC3
VCC3 = 3.0 V,
TA = 25 °C

10
100
µA
Power current

Power current
(FLASH
models)
ICC3
VCC3
VCC3 = 3.3 V

80
120
mA
ICCS3
VCC3
VCC3 = 3.3 V

50
90
mA
Input capacity
CIN
Other than VCC,
AVCC, AVSS,
AVRH and VSS

10

pF
*1 : Refer to “PIN FUNCTION DESCRIPTIONS”
*2 : In case of CLK pin output only (CL = 80 pF)
*3 : Output pin OPEN
90

*2
*2
*3
MB91133/MB91F133
4. AC Characteristics
(1) Clock Timing Standard
(MASK Model VCC5 = AVCC = DAVC = 5.0 V ± 10%, VCC3 = 2.7 V to 3.6 V, VSS = AVSS = 0 V, TA = −40 °C to +70 °C)
(FLASH Model VCC5 = AVCC = DAVC = 5.0 V ± 10%, VCC3 = 3.0 V to 3.6 V, VSS = AVSS = 0 V, TA = −40 °C to +70 °C)
Value
SymCondiParameter
Pin name
Unit
Remarks
bol
tions
Min.
Max.
Clock frequency
(high-speed, self-oscillation)
Self oscillation
available area
fC
X0, X1
Clock frequency (low-speed)
fCA
X0A, X1A
Clock cycle time
tC

30.3
31250
ns
Frequency fluctuation rate *1
(when PLL locked)
∆f


10
%
0.032
33
0.032
25
0.032
25
Excluding analog
area *2
1
25
Analog area *2
30.3
31250
40
31250
40
31250
Excluding analog
area *2
40
1000
Analog area *2
Clock frequency
(high-speed, PLL usage)
Internal operation
clock frequency
CPU
system
fCP
Bus
system
fCPB
Peripheral
system
Internal operation
clock cycle time


fCPP
tCP
Bus
system
tCPB
16.5
32

CPU
system
Peripheral
system
9

tCPP
MHz
kHz
PLL usable area by
self-oscillation input
Self oscillation
MHz
ns
*1 : Frequency fluctuation rate indicates the maximum fluctuation ratio from the setting central frequency during
locking in case of doubling.
*2 : The targeted analog areas are the A/D and level comparator.
91
MB91133/MB91F133
−α
|α|
fO
∆f =
×100 (%)
Central frequency fO
−α
tC
VCC3
0.8 VCC3
0.2 VCC3
VSS
Peripheral system clock setting permitted area (A/D, D/A level comparator : 5 V ± 10%)
< MASK ROM model >
< FLASH model >
VCC3
VCC3
Guaranteed operating range
3.0
fCP
fCPP
Power voltage (V)
Power voltage (V)
Guaranteed operating range
3.6
3.6
fCP
2.7
fCPP
32 K 1 M
25 M 33 M
Frequency (Hz)
92
32 K 1 M
25 M 33 M
Frequency (Hz)
MB91133/MB91F133
The relationship between the internal clock set by the CHC/CCK1/CCK0 bit of the Gear Control Register (GCR)
and X0 input is as follows.
X0 input
• Original oscillation × 1
(CHC bit of GCR : 0 setting)
(a) Gear × 1 Internal clock
CCK1/0 : 00
(b) Gear × 1/2 Internal clock
CCK1/0 : 01
tCYC
tCYC
tCYC
(c) Gear × 1/4 Internal clock
CCK1/0 : 10
tCYC
(d) Gear × 1/8 Internal clock
CCK1/0 : 11
• Original oscillation × 1/2
(CHC bit of GCR : 1 setting)
(a) Gear × 1 Internal clock
CCK1/0 : 00
(b) Gear × 1/2 Internal clock
CCK1/0 : 01
(c) Gear × 1/4 Internal clock
CCK1/0 : 10
(d) Gear × 1/8 Internal clock
CCK1/0 : 11
tCYC
tCYC
tCYC
tCYC
93
MB91133/MB91F133
(2) Reset Input Standards
(MASK Model VCC5 = AVCC = DAVC = 5.0 V ± 10%, VCC3 = 2.7 V to 3.6 V, VSS = AVSS = 0 V, TA = −40 °C to +70 °C)
(FLASH Model VCC5 = AVCC = DAVC = 5.0 V ± 10%, VCC3 = 3.0 V to 3.6 V, VSS = AVSS = 0 V, TA = −40 °C to +70 °C)
Value
Pin
CondiParameter
Symbol
Unit
Remarks
name
tions
Min.
Max.
Reset input time

RST
tRSTL
tCP × 5

ns
tRSTL
RST
0.2 VCC
(3) Power On Reset
(MASK Model VCC5 = AVCC = DAVC = 5.0 V ± 10%, VCC3 = 2.7 V to 3.6 V, VSS = AVSS = 0 V, TA = −40 °C to +70 °C)
(FLASH Model VCC5 = AVCC = DAVC = 5.0 V ± 10%, VCC3 = 3.0 V to 3.6 V, VSS = AVSS = 0 V, TA = −40 °C to +70 °C)
Value
SymPin
Parameter
Conditions
Unit
Remarks
bol
name
Min.
Max.
Power startup time
fR
Power cut time
tOFF
Waiting time for oscillation
stabilization
tOSC
VCC



20
ms
2

ms
213 tC

ns
tR
VhhR
tOFF
0.9 × VCC3
0.2 V
If the power voltage is changed rapidly, “Power On Reset” may be initiated. To start up smoothly,
controlling any voltage fluctuations that may occur during operation is recommended.
VCC
Holding RAM data
Controling inclination at initiation to 50
mV/ms or less is recommended.
VSS
VCC
tOSC (waiting for oscillation stabilization)
RST
tRSTL
94
When power is turned on, start while the RST pin
is set to “L” level, after which wait for tRSTL minutes
and change the level to “H” once the VCC power
level is reached.
MB91133/MB91F133
(4) Serial I/O (CH0 to 4)
(MASK Model VCC5 = AVCC = DAVC = 5.0 V ± 10%, VCC3 = 2.7 V to 3.6 V, VSS = AVSS = 0 V, TA = −40 °C to +70 °C)
(FLASH Model VCC5 = AVCC = DAVC = 5.0 V ± 10%, VCC3 = 3.0 V to 3.6 V, VSS = AVSS = 0 V, TA = −40 °C to +70 °C)
Value
Pin
Parameter
Symbol
Conditions
Unit Remarks
name
Min.
Max.
Serial clock cycle time
tSCYC

8 tCPP

ns
SCK ↓ → SO delay time
tSLOV

−10
50
ns
Valid SI → SCK ↑
tIVSH

50

ns
SCK ↑ → Valid SI holding time
tSHIX

50

ns
Serial clock H pulse width
tSHSL

4 tCPP − 10

ns
Serial clock L pulse width
tSLSH

4 tCPP − 10

ns
SCK ↓ → SO delay time
tSLOV

0
50
ns
Valid SI → SCK ↑
tIVSH

50

ns
50

ns

6 tCPP
ns
Internal
clock
External
clock
SCK ↑ → Valid SI holding time
tSHIX

Serial busy period
tBUSY

SCS ↓ → SCK, SO delay time
tCLZO


50
ns
SCS ↓ → SCK input MASK time
tCLSL


3 tCPP
ns
SCS ↑ → SCK, SO Hi-Z time
tCHOZ

50

ns
*
*: Will be Min. 1 tCPP − 10 if pre-scalar setting is CS2, 1, 0 = 000.
Internal shift clock mode
tSCYC
SCK
tSLOV
SO
SI
tSHIX
tIVSH
External shift clock mode
tCLZO
tSLSH
tSHSL
tBUSY
tCHOZ
SCK
tSLOV
SO
SI
tIVSH
tSHIX
SCS
tCLSL
95
MB91133/MB91F133
(5) External Bus Measurement Conditions
The following conditions apply to items without specific regulations.
• Alternating current standard measurement condition
VCC : 5.0 V ± 10%
Input
Output
VCC
VIH
VOH
VIL
VOL
0V
VIH
2.4 V
VOH
2.4V
VIL
0.8 V
VOL
0.8V
(Rise/fall time of input is 10 ns or less)
• Load condition
Output pin
C = 50 pF
( VCC : 5.0 V ± 10% )
• Load capacity − Delay time characteristic (Internally-based output delay)
[nS]
35
30
25
5 V Fall
20
15
5 V Rise
10
5
0
0
96
20
40
50
60
80
100
120
C[pF]
MB91133/MB91F133
(6) Normal Bus Access Read/Write Operation
(MASK Model VCC5 = AVCC = DAVC = 5.0 V ± 10%, VCC3 = 2.7 V to 3.6 V, VSS = AVSS = 0 V, TA = −40 °C to +70 °C)
(FLASH Model VCC5 = AVCC = DAVC = 5.0 V ± 10%, VCC3 = 3.0 V to 3.6 V, VSS = AVSS = 0 V, TA = −40 °C to +70 °C)
Value
SymParameter
Pin name Conditions
Unit Remarks
bol
Min.
Max.
Address delay time
tCHAV
CLK
A23 to A00

15
ns
Data delay time
tCHDV
CLK
D31 to D16

15
ns
RD delay time
tCLRL

10
ns
RD delay time
tCLRH

10
ns
WR0 to 1 delay time
tCLWL

10
ns
WR0 to 1 delay time
tCLWH

10
ns
Valid address / valid data input time
tAVDV

3/2×
tCYC − 25
ns
*1, *2
RD ↓ → valid data input time
tRLDV

tCYC − 15
ns
*1
15

ns
0

ns
Data setup → RD ↑ time
tDSRH
RD ↑ → Data holding time
tRHDX
CLK
RD
CLK
WR0 to 1
A23 to A00
D31 to D16
RD
D31 to D16

*1 : Time (tCYC × number of cycles extended) needs to be added to this standard if the bus is extended by automatic
waiting insertion and RDY input.
*2 : Values of this standard are in case of gear cycle × 1.
If the gear cycle is set to 1/2, 1/4 or 1/8, calculation should be made using the following formula and replacing
n with 1/2, 1/4 or 1/8.
• Calculation formula : (2 − n / 2) × tCYC − 25
97
MB91133/MB91F133
tCYC
BA1
BA2
VOH
VOH
VOL
CLK
VOL
tCHAV
VOH
VOL
A24 - A00
VOH
VOL
tCLRL
tCLRH
VOH
RD
VOL
tRLDV
tRHDX
tAVDV
tDSRH
VIH
VIL
D31 - D16
tCLWL
Read
VIH
VIL
tCLWH
VOH
WR0 - WR1
VOL
tCHDV
D31 - D16
98
VOH
VOL
Write
VOH
VOL
MB91133/MB91F133
(7) Ready Input Timing
(MASK Model VCC5 = AVCC = DAVC = 5.0 V ± 10%, VCC3 = 2.7 V to 3.6 V, VSS = AVSS = 0 V, TA = −40 °C to +70 °C)
(FLASH Model VCC5 = AVCC = DAVC = 5.0 V ± 10%, VCC3 = 3.0 V to 3.6 V, VSS = AVSS = 0 V, TA = −40 °C to +70 °C)
Value
Pin
Parameter
Symbol
Conditions
Unit
Remarks
name
Min.
Max.
RDY setup time → CLK ↓
CLK ↓ → RDY holding time
tRDYS
RDY
CLK
tRDYH
RDY
CLK
15

ns
0

ns

tCYC
VOH
VOH
CLK
VOL
VOL
tRDYS
RDY
If "wait" is
executed
VIL
RDY
If "wait" is
not executed
VIH
tRDYH
tRDYS tRDYH
VIH
VIL
99
MB91133/MB91F133
(8) Holding timing
(MASK Model VCC5 = AVCC = DAVC = 5.0 V ± 10%, VCC3 = 2.7 V to 3.6 V, VSS = AVSS = 0 V, TA = −40 °C to +70 °C)
(FLASH Model VCC5 = AVCC = DAVC = 5.0 V ± 10%, VCC3 = 3.0 V to 3.6 V, VSS = AVSS = 0 V, TA = −40 °C to +70 °C)
Value
Pin
Parameter
Symbol
Conditions
Unit
Remarks
name
Min.
Max.
BGRNT delay time
tCHBGL
BGRNT delay time
tCHBGH
Pin floating → BGRNT ↓ time
tXHAL
BGRNT ↑ → Pin valid time
tHAHV
CLK
BGRNT

BGRNT

6
ns

6
ns
tCYC − 10
tCYC + 10
ns
tCYC − 10
tCYC + 10
ns
Note : It takes at least one cycle from loading the BRQ to when BGRNT is changed.
tcyc
VOH
VOH
VOH
VOH
CLK
BRQ
tCHBGL
tCHBGH
VOH
BGRNT
VOL
tHAHV
tXHAL
Each pin
High impedance
100
MB91133/MB91F133
(9) DMA Controller Timing
(MASK Model VCC5 = AVCC = DAVC = 5.0 V ± 10%, VCC3 = 2.7 V to 3.6 V, VSS = AVSS = 0 V, TA = −40 °C to +70 °C)
(FLASH Model VCC5 = AVCC = DAVC = 5.0 V ± 10%, VCC3 = 3.0 V to 3.6 V, VSS = AVSS = 0 V, TA = −40 °C to +70 °C)
Value
Parameter
Symbol
Pin name
Conditions
Unit Remarks
Min.
Max.
DREQ input pulse width
tDRWH
DREQ0 to DREQ2
DACK delay time
(Normal bus)
tCLDL
CLK
DACK0 to DACK2
tCLDH
tCLEL
EOP delay time
(Normal bus)
CLK
EOP0 to EOP2
tCLEH
DACK delay time
tCHDL
tCHDH

ns

6
ns

6
ns

6
ns

6
ns

n / 2 × tCYC
ns

6
ns

n / 2 × tCYC
ns

6
ns

CLK
DACK0 to DACK2
tCHEL
EOP delay time
2 tCYC
CLK
EOP0 to EOP2
tCHEH
tcyc
VOH
VOH
CLK
VOL
VOL
tCLDH
tCLDL
tCLEL
DACK0 - 2
EOP0 - 2
(Normal bus)
tCLEH
VOH
VOL
tCHDH
DACK0 - 2
EOP0 - 2
tCHDL
VOH
VOL
tCHEL
tDRWH
DREQ0 - 2
VIH
VIH
101
MB91133/MB91F133
5. A/D Transition
(MASK Model VCC5 = AVCC = DAVC = 5.0 V ± 10%, VCC3 = 2.7 V to 3.6 V, VSS = AVSS = 0 V, TA = −40 °C to +70 °C)
(FLASH Model VCC5 = AVCC = DAVC = 5.0 V ± 10%, VCC3 = 3.0 V to 3.6 V, VSS = AVSS = 0 V, TA = −40 °C to +70 °C)
Value
ReSymPin
Conditions
Unit
Parameter
marks
bol
name
Min.
Typ.
Max.
Resolution


Conversion time


Total tolerance


Straight-line tolerance


Differential straight-line
tolerance


Zero transition tolerance
VOT
Full-scale transition
tolerance
VFST
Analog input current
IAIN
AN0 to
AN7
Analog input voltage
VAIN
AN0 to
AN7
Standard voltage
AVRH
AVRH
Power
current
Standard
voltage
current
supplied
When conversion
is activated
IA
When conversion
is stopped
IAH
When conversion
is activated
IR
When conversion
is stopped
IRH
Tolerance between
channels
AVCC = 5.0 V,
AVRH = 5.0 V


5.0

−4.0

4.0
LSB
−3.5

3.5
LSB
−2.0

2.0
LSB
10
Bit
µs
AN0 to
AVSS−1.5 AVSS+0.5 AVSS+2.5 LSB
AN7 AVCC = 5.0 V,
AN0 to AVRH = 5.0 V
AVRH − 5.5 AVRH − 1.5 AVRH + 0.5 LSB
AN7
AVCC
AVRH


AN0 to
AN7

0.1
10
µA
AVSS

AVRH
V


AVCC
V

3.0
5.0
mA


5.0
µA

2.0
3.0
mA


10
µA


4
LSB


AVCC = 5.0 V
AVCC = 5.0 V,
AVRH = 5.0V

Notes : • As the |AVRH| becomes smaller, the tolerance becomes larger.
• Output impedance of external circuits other than analog input must be used if output impedance of external
circuits < approx. 7 kΩ
If the output impedance of the external circuits is too high, the sampling time for the analog voltage may
be insufficient.
(Sampling time = 1.6 µs at 33 MHz)
102
MB91133/MB91F133
• Definition of A/D Converter Terms
• Resolution :
Analog changes that can be identified by A/D converter
• Straight-line tolerance :
Difference between the straight line linking the zero transition point (00 0000 0000 ←→ 00 0000 0001) to the
full-scale transition point (11 1111 1110 ←→ 11 1111 1111) and actual conversion characteristics.
• Differential straight-line tolerance :
Difference compared to the ideal input voltage value required to change the output code 1 LSB
• Total tolerance :
Indicates the difference between the actual and theoretical values and includes zero transition tolerance, fullscale transition tolerance, and straight-line tolerance.
Total tolerance
3FF
3FE
Digital output
3FD
Actual conversion
characteristics
{1 LSB ( N − 1 ) + 0.5 LSB}
1.5 LSB
004
VNT
(Actual
measured value)
Actual conversion
characteristics
003
002
Ideal characteristics
001
0.5 LSB
AVRH
AVSS
Total tolerance of digital output N =
1 LSB (Ideal value) =
VNT − {1 LSB × (N − 1) + 0.5 LSB’}
1 LSB
AVRH − AVSS
1024
VOT (Ideal value) = AVSS + 0.5 LSB’
Analog input
[V]
[V]
VFST (Ideal value) = AVRH − 1.5 LSB’ [V]
VNT : Voltage of digital output transferred from (N + 1) to N
(Continued)
103
MB91133/MB91F133
(Continued)
Straight-line tolerance
Differential straight-line tolerance
3FF
Actual conversion
characteristics
{1 LSB ( N − 1 ) + VOT}
VFST
(Actual
measured
value)
Digital output
3FD
004
VNT
(Actual
measured value)
003
Actual conversion
characteristics
N+1
Digital output
3FE
N
Ideal characteristics
N−1
VFST
(Actual
measured
VNT
value)
(Actual
measured value)
Actual conversion
characteristics
Ideal characteristics
002
001
N−2
VOT
(Actual measured value)
AVSS
AVSS
AVRH
Analog input
Actual conversion
characteristics
Straight-line tolerance = VNT − {1 LSB × (N − 1) + VOT}
1 LSB
of digital output N
Differential straight-line tolerance
=
of digital output N
1LSB (Ideal value) =
V (N + 1) T − VNT
1 LSB
VFST − VOT
1022
−1
AVRH
Analog input
[LSB]
[LSB]
[V]
VOT : Voltage with digital output transferred from (000) H to (001) H
VFST : Voltage with digital output transferred from (3FE) H to (3FF) H
6. D/A Transition
(MASK Model VCC5 = AVCC = DAVC = 5.0 V ± 10%, VCC3 = 2.7 V to 3.6 V, VSS = AVSS = 0 V, TA = −40 °C to +70 °C)
(FLASH Model VCC5 = AVCC = DAVC = 5.0 V ± 10%, VCC3 = 3.0 V to 3.6 V, VSS = AVSS = 0 V, TA = −40 °C to +70 °C)
Value
Pin
CondiReParameter
Symbol
Unit
name
tions
marks
Min.
Typ.
Max.
Resolution





8
Bit
Differential straight-line tolerance





±0.9
LSB
Conversion time




10
20
µs
Analog output impedance




28

kΩ
*: CL = 20 PF
104
*
MB91133/MB91F133
■ INSTRUCTIONS (165 INSTRUCTIONS)
1. How to Read Instruction Set Summary
Mnemonic
ADD
* ADD
↓
(1)
Rj,
Ri
#s5, Ri
,
,
↓
(2)
Type
OP
CYC
NZVC
Operation
A
C
,
,
A6
A4
,
,
1
1
,
,
CCCC
CCCC
,
,
Ri + Rj → Ri
Ri + s5 → Ri
,
,
↓
(3)
↓
(4)
↓
(5)
↓
(6)
↓
(7)
Remarks
(1) Names of instructions
Instructions marked with * are not included in CPU specifications. These are extended instruction codes
added/extended at assembly language levels.
(2) Addressing modes specified as operands are listed in symbols.
Refer to “2. Addressing mode symbols” for further information.
(3) Instruction types
(4) Hexa-decimal expressions of instructions
(5) The number of machine cycles needed for execution
a: Memory access cycle and it has possibility of delay by Ready function.
b: Memory access cycle and it has possibility of delay by Ready function.
If an object register in a LD operation is referenced by an immediately following instruction, the interlock
function is activated and number of cycles needed for execution increases.
c: If an immediately following instruction operates to an object of R15, SSP or USP in read/write mode or
if the instruction belongs to instruction format A group, the interlock function is activated and number of
cycles needed for execution increases by 1 to make the total number of 2 cycles needed.
d: If an immediately following instruction refers to MDH/MDL, the interlock function is activated and number
of cycles needed for execution increases by 1 to make the total number of 2 cycles needed.
For a, b, c and d, minimum execution cycle is 1.
(6) Change in flag sign
• Flag change
C : Change
– : No change
0 : Clear
1 : Set
• Flag meanings
N : Negative flag
Z : Zero flag
V : Over flag
C : Carry flag
(7) Operation carried out by instruction
105
MB91133/MB91F133
2. Addressing Mode Symbols
Ri
Rj
R13
Ps
Rs
CRi
CRj
#i8
: Register direct (R0 to R15, AC, FP, SP)
: Register direct (R0 to R15, AC, FP, SP)
: Register direct (R13, AC)
: Register direct (Program status register)
: Register direct (TBR, RP, SSP, USP, MDH, MDL)
: Register direct (CR0 to CR15)
: Register direct (CR0 to CR15)
: Unsigned 8-bit immediate (–128 to 255)
Note: –128 to –1 are interpreted as 128 to 255
#i20
: Unsigned 20-bit immediate (–0X80000 to 0XFFFFF)
Note: –0X7FFFF to –1 are interpreted as 0X7FFFF to 0XFFFFF
#i32
: Unsigned 32-bit immediate (–0X80000000 to 0XFFFFFFFF)
Note: –0X80000000 to –1 are interpreted as 0X80000000 to 0XFFFFFFFF
#s5
: Signed 5-bit immediate (–16 to 15)
#s10
: Signed 10-bit immediate (–512 to 508, multiple of 4 only)
#u4
: Unsigned 4-bit immediate (0 to 15)
#u5
: Unsigned 5-bit immediate (0 to 31)
#u8
: Unsigned 8-bit immediate (0 to 255)
#u10
: Unsigned 10-bit immediate (0 to 1020, multiple of 4 only)
@dir8
: Unsigned 8-bit direct address (0 to 0XFF)
@dir9
: Unsigned 9-bit direct address (0 to 0X1FE, multiple of 2 only)
@dir10
: Unsigned 10-bit direct address (0 to 0X3FC, multiple of 4 only)
label9
: Signed 9-bit branch address (–0X100 to 0XFC, multiple of 2 only)
label12
: Signed 12-bit branch address (–0X800 to 0X7FC, multiple of 2 only)
label20
: Signed 20-bit branch address (–0X80000 to 0X7FFFF)
label32
: Signed 32-bit branch address (–0X80000000 to 0X7FFFFFFF)
@Ri
: Register indirect (R0 to R15, AC, FP, SP)
@Rj
: Register indirect (R0 to R15, AC, FP, SP)
@(R13, Rj)
: Register relative indirect (Rj: R0 to R15, AC, FP, SP)
@(R14, disp10) : Register relative indirect (disp10: –0X200 to 0X1FC, multiple of 4 only)
@(R14, disp9) : Register relative indirect (disp9: –0X100 to 0XFE, multiple of 2 only)
@(R14, disp8) : Register relative indirect (disp8: –0X80 to 0X7F)
@(R15, udisp6) : Register relative (udisp6: 0 to 60, multiple of 4 only)
@Ri+
: Register indirect with post-increment (R0 to R15, AC, FP, SP)
@R13+
: Register indirect with post-increment (R13, AC)
@SP+
: Stack pop
@–SP
: Stack push
(reglist)
: Register list
106
MB91133/MB91F133
3. Instruction Types
MSB
Type A
Type B
LSB
16 bits
OP
Rj
Ri
8
4
4
OP
i8/o8
Ri
4
8
4
Type C
OP
u4/m4
Ri
8
4
4
ADD, ADDN, CMP, LSL, LSR and ASR instructions only
Type *C’
Type D
Type E
Type F
OP
s5/u5
Ri
7
5
4
OP
u8/rel8/dir/reglist
8
8
OP
SUB-OP
Ri
8
4
4
OP
rel11
5
11
107
MB91133/MB91F133
4. Detailed Description of Instructions
• Add/subtract operation instructions (10 instructions)
Mnemonic
Type
OP
Cycle N Z V C
Operation
ADD
* ADD
Rj, Ri
#s5, Ri
A
C’
A6
A4
1
1
C C C C Ri + Rj → Ri
C C C C Ri + s5 → Ri
ADD
ADD2
#i4, Ri
#i4, Ri
C
C
A4
A5
1
1
C C C C Ri + extu (i4) → Ri
C C C C Ri + extu (i4) → Ri
ADDC
Rj, Ri
A
A7
1
C C C C Ri + Rj + c → Ri
ADDN
* ADDN
Rj, Ri
#s5, Ri
A
C’
A2
A0
1
1
– – – – Ri + Rj → Ri
– – – – Ri + s5 → Ri
ADDN
ADDN2
#i4, Ri
#i4, Ri
C
C
A0
A1
1
1
– – – – Ri + extu (i4) → Ri
– – – – Ri + extu (i4) → Ri
SUB
Rj, Ri
A
AC
1
C C C C Ri – Rj → Ri
SUBC
Rj, Ri
A
AD
1
C C C C Ri – Rj – c → Ri
SUBN
Rj, Ri
A
AE
1
– – – – Ri – Rj → Ri
Remarks
MSB is interpreted as
a sign in assembly
language
Zero-extension
Sign-extension
Add operation with
sign
MSB is interpreted as
a sign in assembly
language
Zero-extension
Sign-extension
Subtract operation with
carry
• Compare operation instructions (3 instructions)
Mnemonic
Type
OP
Cycle N Z V C
Operation
CMP
* CMP
Rj, Ri
#s5, Ri
A
C’
AA
A8
1
1
C C C C Ri – Rj
C C C C Ri – s5
CMP
CMP2
#i4, Ri
#i4, Ri
C
C
A8
A9
1
1
C C C C Ri + extu (i4)
C C C C Ri + extu (i4)
Remarks
MSB is interpreted as
a sign in assembly
language
Zero-extension
Sign-extension
• Logical operation instructions (12 instructions)
108
Mnemonic
Type
OP
Cycle N Z V C
AND
AND
ANDH
ANDB
Rj, Ri
Rj, @Ri
Rj, @Ri
Rj, @Ri
A
A
A
A
82
84
85
86
1
1 + 2a
1 + 2a
1 + 2a
CC
CC
CC
CC
–
–
–
–
–
–
–
–
Ri &
(Ri) &
(Ri) &
(Ri) &
= Rj
= Rj
= Rj
= Rj
Word
Word
Half word
Byte
OR
OR
ORH
ORB
Rj, Ri
Rj, @Ri
Rj, @Ri
Rj, @Ri
A
A
A
A
92
94
95
96
1
1 + 2a
1 + 2a
1 + 2a
CC
CC
CC
CC
–
–
–
–
–
–
–
–
Ri
(Ri)
(Ri)
(Ri)
|
|
|
|
= Rj
= Rj
= Rj
= Rj
Word
Word
Half word
Byte
EOR
EOR
EORH
EORB
Rj, Ri
Rj, @Ri
Rj, @Ri
Rj, @Ri
A
A
A
A
9A
9C
9D
9E
1
1 + 2a
1 + 2a
1 + 2a
CC
CC
CC
CC
–
–
–
–
–
–
–
–
Ri ^
(Ri) ^
(Ri) ^
(Ri) ^
= Rj
= Rj
= Rj
= Rj
Word
Word
Half word
Byte
Operation
Remarks
MB91133/MB91F133
• Bit manipulation arithmetic instructions (8 instructions)
Mnemonic
BANDL
BANDH
* BAND
BORL
BORH
* BOR
BEORL
BEORH
* BEOR
BTSTL
BTSTH
#u4, @Ri
(u4: 0 to 0FH)
#u4, @Ri
(u4: 0 to 0FH)
#u8, @Ri
#u4, @Ri
(u4: 0 to 0FH)
#u4, @Ri
(u4: 0 to 0FH)
#u8, @Ri
#u4, @Ri
(u4: 0 to 0FH)
#u4, @Ri
(u4: 0 to 0FH)
#u8, @Ri
Type
OP
Cycle N Z V C
C
80
1 + 2a – – – – (Ri) & = (F0H + u4)
Manipulate lower 4 bits
C
81
1 + 2a – – – – (Ri) & = ((u4<<4) + 0FH)
Manipulate upper 4 bits
–
*1
Remarks
– – – – (Ri) & = u8
C
90
1 + 2a – – – – (Ri) | = u4
Manipulate lower 4 bits
C
91
1 + 2a – – – – (Ri) | = (u4<<4)
Manipulate upper 4 bits
–
*2
– – – – (Ri) | = u8
C
98
1 + 2a – – – – (Ri) ^ = u4
Manipulate lower 4 bits
C
99
1 + 2a – – – – (Ri) ^ = (u4<<4)
Manipulate upper 4 bits
–
*3
#u4, @Ri
(u4: 0 to 0FH)
#u4, @Ri
(u4: 0 to 0FH)
Operation
– – – – (Ri) ^ = u8
C
88
2+a
0 C – – (Ri) & u4
Test lower 4 bits
C
89
2+a
C C – – (Ri) & (u4<<4)
Test upper 4 bits
*1: Assembler generates BANDL if result of logical operation “u8&0x0F” leaves an active (set) bit and generates
BANDH if “u8&0xF0” leaves an active bit. Depending on the value in the “u8” format, both BANDL and BANDH
may be generated.
*2: Assembler generates BORL if result of logical operation “u8&0x0F” leaves an active (set) bit and generates
BORH if “u8&0xF0” leaves an active bit.
*3: Assembler generates BEORL if result of logical operation “u8&0x0F” leaves an active (set) bit and generates
BEORH if “u8&0xF0” leaves an active bit.
• Add/subtract operation instructions (10 instructions)
Mnemonic
Type
OP
Cycle N Z V C
MUL
MULU
MULH
MULUH
Rj, Ri
Rj, Ri
Rj, Ri
Rj, Ri
A
A
A
A
AF
AB
BF
BB
5
5
3
3
CCC
CCC
CC–
CC–
DIVOS
DIVOU
DIV1
DIV2
DIV3
DIV4S
* DIV
Ri
Ri
Ri
Ri
E
E
E
E
E
E
97 – 4
97 – 5
97 – 6
97 – 7
9F – 6
9F – 7
Ri
*1
1
1
d
1
1
1
–
–
–
–
–
–
–
–
* DIVU
Ri
*2
–
–
–
C
C
–
–
C
–
–
–
–
–
–
–
–
–
–
–
Operation
Rj × Ri → MDH, MDL
Rj × Ri → MDH, MDL
Rj × Ri → MDL
Rj × Ri → MDL
–
–
C
C
–
–
C MDL/Ri → MDL,
MDL%Ri → MDH
– C – C MDL/Ri → MDL,
MDL%Ri → MDH
Remarks
32-bit × 32-bit = 64-bit
Unsigned
16-bit × 16-bit = 32-bit
Unsigned
Step calculation
32-bit/32-bit = 32-bit
Unsigned
*1: DIVOS, DIV1 × 32, DIV2, DIV3 and DIV4S are generated. A total instruction code length of 72 bytes.
*2: DIVOU and DIV1 × 32 are generated. A total instruction code length of 66 bytes.
109
MB91133/MB91F133
• Shift arithmetic instructions (9 instructions)
Mnemonic
Type
OP
Cycle N Z V C
Operation
Remarks
LSL
* LSL
LSL
LSL2
Rj, Ri
#u5, Ri
#u4, Ri
#u4, Ri
A
C’
C
C
B6
B4
B4
B5
1
1
1
1
CC
CC
CC
CC
–
–
–
–
C
C
C
C
Ri<<Rj → Ri
Ri<<u5 → Ri
Ri<<u4 → Ri
Ri<<(u4 + 16) → Ri
Logical shift
LSR
* LSR
LSR
LSR2
Rj, Ri
#u5, Ri
#u4, Ri
#u4, Ri
A
C’
C
C
B2
B0
B0
B1
1
1
1
1
CC
CC
CC
CC
–
–
–
–
C
C
C
C
Ri>>Rj → Ri
Ri>>u5 → Ri
Ri>>u4 → Ri
Ri>>(u4 + 16) → Ri
Logical shift
ASR
* ASR
ASR
ASR2
Rj, Ri
#u5, Ri
#u4, Ri
#u4, Ri
A
C’
C
C
BA
B8
B8
B9
1
1
1
1
CC
CC
CC
CC
–
–
–
–
C
C
C
C
Ri>>Rj → Ri
Ri>>u5 → Ri
Ri>>u4 → Ri
Ri>>(u4 + 16) → Ri
Logical shift
• Immediate value data transfer instruction (immediate value set/16-bit/32-bit immediate value transfer
instruction) (3 instructions)
Mnemonic
Type
OP
Cycle N Z V C
Operation
LDI: 32
LDI: 20
#i32, Ri
#i20, Ri
E
C
9F – 8
9B
3
2
– – – – i32 → Ri
– – – – i20 → Ri
LDI: 8
* LDI
#i8, Ri
# {i8 | i20 | i32}, Ri
*1
B
C0
1
– – – – i8 → Ri
{i8 | i20 | i32} → Ri
Remarks
Upper 12 bits are zeroextended
Upper 24 bits are zeroextended
*1: If an immediate value is given in absolute, assembler automatically makes i8, i20 or i32 selection.
If an immediate value contains relative value or external reference, assembler selects i32.
• Memory load instructions (13 instructions)
Mnemonic
Type
OP
Cycle N Z V C
Operation
(Rj) → Ri
(R13 + Rj) → Ri
(R14 + disp10) → Ri
(R15 + udisp6) → Ri
(R15) → Ri, R15 + = 4
(R15) → Rs, R15 + = 4
Remarks
LD
LD
LD
LD
LD
LD
@Rj, Ri
@(R13, Rj), Ri
@(R14, disp10), Ri
@(R15, udisp6), Ri
@R15 +, Ri
@R15 +, Rs
A
A
B
C
E
E
04
00
20
03
07 – 0
07 – 8
b
b
b
b
b
b
LD
@R15 +, PS
E
07 – 9
1+a+b
LDUH
LDUH
LDUH
@Rj, Ri
@(R13, Rj), Ri
@(R14, disp9), Ri
A
A
B
05
01
40
b
b
b
– – – – (Rj) → Ri
– – – – (R13 + Rj) → Ri
– – – – (R14 + disp9) → Ri
Zero-extension
Zero-extension
Zero-extension
LDUB
LDUB
LDUB
@Rj, Ri
@(R13, Rj), Ri
@(R14, disp8), Ri
A
A
B
06
02
60
b
b
b
– – – – (Rj) → Ri
– – – – (R13 + Rj) → Ri
– – – – (R14 + disp8) → Ri
Zero-extension
Zero-extension
Zero-extension
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
C C C C (R15) → PS, R15 + = 4
Rs: Special-purpose
register
Note: The relations between o8 field of TYPE-B and u4 field of TYPE-C in the instruction format and assembler
description from disp8 to disp10 are as follows:
disp8 → o8 = disp8:Each disp is a code extension.
disp9 → o8 = disp9>>1:Each disp is a code extension.
disp10 → o8 = disp10>>2:Each disp is a code extension.
udisp6 → u4 = udisp6>>2:udisp4 is a 0 extension.
110
MB91133/MB91F133
• Memory store instructions (13 instructions)
Mnemonic
Type
OP
Cycle N Z V C
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Operation
Ri → (Rj)
Ri → (R13 + Rj)
Ri → (R14 + disp10)
Ri → (R15 + usidp6)
R15 – = 4, Ri → (R15)
R15 – = 4, Rs → (R15)
Remarks
ST
ST
ST
ST
ST
ST
Ri, @Rj
Ri, @(R13, Rj)
Ri, @(R14, disp10)
Ri, @(R15, udisp6)
Ri, @–R15
Rs, @–R15
A
A
B
C
E
E
14
10
30
13
17 – 0
17 – 8
a
a
a
a
a
a
–
–
–
–
–
–
Word
Word
Word
ST
PS, @–R15
E
17 – 9
a
– – – – R15 – = 4, PS → (R15)
STH
STH
STH
Ri, @Rj
Ri, @(R13, Rj)
Ri, @(R14, disp9)
A
A
B
15
11
50
a
a
a
– – – – Ri → (Rj)
– – – – Ri → (R13 + Rj)
– – – – Ri → (R14 + disp9)
Half word
Half word
Half word
STB
STB
STB
Ri, @Rj
Ri, @(R13, Rj)
Ri, @(R14, disp8)
A
A
B
16
12
70
a
a
a
– – – – Ri → (Rj)
– – – – Ri → (R13 + Rj)
– – – – Ri → (R14 + disp8)
Byte
Byte
Byte
Rs: Special-purpose
register
Note: The relations between o8 field of TYPE-B and u4 field of TYPE-C in the instruction format and assembler
description from disp8 to disp10 are as follows:
disp8 → o8 = disp8:Each disp is a code extension.
disp9 → o8 = disp9>>1:Each disp is a code extension.
disp10 → o8 = disp10>>2:Each disp is a code extension.
udisp6 → u4 = udisp6>>2:udisp4 is a 0 extension.
• Transfer instructions between registers/special-purpose registers transfer instructions
(5 instructions)
Mnemonic
Type
OP
Cycle N Z V C
Operation
MOV
Rj, Ri
A
8B
1
– – – – Rj → Ri
MOV
Rs, Ri
A
B7
1
– – – – Rs → Ri
MOV
Ri, Rs
A
B3
1
– – – – Ri → Rs
MOV
MOV
PS, Ri
Ri, PS
E
E
17 – 1
07 – 1
1
c
– – – – PS → Ri
C C C C Ri → PS
Remarks
Transfer between
general-purpose
registers
Rs: Special-purpose
register
Rs: Special-purpose
register
111
MB91133/MB91F133
• Non-delay normal branch instructions (23 instructions)
Mnemonic
Type
OP
Cycle N Z V C
Operation
JMP
@Ri
E
97 – 0
2
– – – – Ri → PC
CALL
label12
F
D0
2
CALL
@Ri
E
97 – 1
2
– – – – PC + 2 → RP,
PC + 2 + rel11 × 2 → PC
– – – – PC + 2 → RP, Ri → PC
E
97 – 2
2
– – – – RP → PC
D
1F
3+3a
RET
INT
#u8
Remarks
Return
– – – – SSP – = 4, PS → (SSP),
SSP – = 4,
PC + 2 → (SSP),
0 → I flag,
0 → S flag,
(TBR + 3FC – u8 × 4) → PC
INTE
E
9F – 3 3 + 3a – – – – SSP – = 4, PS → (SSP),
For emulator
SSP – = 4,
PC + 2 → (SSP),
0 → S flag,
(TBR + 3D8 – u8 × 4) → PC
RETI
E
97 – 3 2 + 2a C C C C (R15) → PC, R15 – = 4,
(R15) → PS, R15 – = 4
BNO
BRA
BEQ
BNE
BC
BNC
BN
BP
BV
BNV
BLT
BGE
BLE
BGT
BLS
BHI
label9
label9
label9
label9
label9
label9
label9
label9
label9
label9
label9
label9
label9
label9
label9
label9
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
E1
E0
E2
E3
E4
E5
E6
E7
E8
E9
EA
EB
EC
ED
EE
EF
1
2
2/1
2/1
2/1
2/1
2/1
2/1
2/1
2/1
2/1
2/1
2/1
2/1
2/1
2/1
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Non-branch
PC + 2 + rel8 × 2 → PC
PCif Z = = 1
PCif Z = = 0
PCif C = = 1
PCif C = = 0
PCif N = = 1
PCif N = = 0
PCif V = = 1
PCif V = = 0
PCif V xor N = = 1
PCif V xor N = = 0
PCif (V xor N) or Z = = 1
PCif (V xor N) or Z = = 0
PCif C or Z = = 1
PCif C or Z = = 0
Notes: • “2/1” in cycle sections indicates that 2 cycles are needed for branch and 1 cycle needed for non-branch.
• The relations between rel8 field of TYPE-D and rel11 field of TYPE-F in the instruction format and
assembler discription label9 and label12 are as follows.
label9 → rel8 = (label9 – PC – 2)/2
label12 → rel11 = (label12 – PC – 2)/2
• RETI must be operated while S flag = 0.
112
MB91133/MB91F133
• Branch instructions with delays (20 instructions)
Mnemonic
Type
OP
Cycle N Z V C
Operation
JMP:D
@Ri
E
9F – 0
1
– – – – Ri → PC
CALL:D
label12
F
D8
1
CALL:D
@Ri
E
9F – 1
1
– – – – PC + 4 → RP,
PC + 2 + rel11 × 2 → PC
– – – – PC + 4 → RP, Ri → PC
E
9F – 2
1
– – – – RP → PC
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
F1
F0
F2
F3
F4
F5
F6
F7
F8
F9
FA
FB
FC
FD
FE
FF
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
RET:D
BNO:D
BRA:D
BEQ:D
BNE:D
BC:D
BNC:D
BN:D
BP:D
BV:D
BNV:D
BLT:D
BGE:D
BLE:D
BGT:D
BLS:D
BHI:D
label9
label9
label9
label9
label9
label9
label9
label9
label9
label9
label9
label9
label9
label9
label9
label9
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Remarks
Return
Non-branch
PC + 2 + rel8 × 2 → PC
PCif Z = = 1
PCif Z = = 0
PCif C = = 1
PCif C = = 0
PCif N = = 1
PCif N = = 0
PCif V = = 1
PCif V = = 0
PCif V xor N = = 1
PCif V xor N = = 0
PCif (V xor N) or Z = = 1
PCif (V xor N) or Z = = 0
PCif C or Z = = 1
PCif C or Z = = 0
Notes: • The relations between rel8 field of TYPE-D and rel11 field of TYPE-F in the instruction format and
assembler discription label9 and label12 are as follows.
label9 → rel8 = (label9 – PC – 2)/2
label12 → rel11 = (label12 – PC – 2)/2
• Delayed branch operation always executes next instruction (delay slot) before making a branch.
• Instructions allowed to be stored in the delay slot must meet one of the following conditions. If the other
instruction is stored, this device may operate other operation than defined.
The instruction described “1” in the other cycle column than branch instruction.
The instruction described “a”, “b”, “c” or “d” in the cycle column.
113
MB91133/MB91F133
• Direct addressing instructions
Mnemonic
Type
OP
Cycle N Z V C
Operation
Remarks
DMOV
DMOV
DMOV
DMOV
DMOV
DMOV
@dir10,
R13,
@dir10,
@R13+,
@dir10,
@R15+,
R13
@dir10
@R13+
@dir10
@–R15
@dir10
D
D
D
D
D
D
08
18
0C
1C
0B
1B
b
a
2a
2a
2a
2a
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
(dir10) → R13
R13 → (dir10)
(dir10) → (R13), R13 + = 4
(R13) → (dir10), R13 + = 4
R15 – = 4, (dir10) → (R15)
(R15) → (dir10), R15 + = 4
Word
Word
Word
Word
Word
Word
DMOVH
DMOVH
DMOVH
DMOVH
@dir9,
R13,
@dir9,
@R13+,
R13
@dir9
@R13+
@dir9
D
D
D
D
09
19
0D
1D
b
a
2a
2a
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
(dir9) → R13
R13 → (dir9)
(dir9) → (R13), R13 + = 2
(R13) → (dir9), R13 + = 2
Half word
Half word
Half word
Half word
DMOVB
DMOVB
DMOVB
DMOVB
@dir8,
R13,
@dir8,
@R13+,
R13
@dir8
@R13+
@dir8
D
D
D
D
0A
1A
0E
1E
b
a
2a
2a
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
(dir8) → R13
R13 → (dir8)
(dir8) → (R13), R13 + +
(R13) → (dir8), R13 + +
Byte
Byte
Byte
Byte
Note: The relations between the dir field of TYPE-D in the instruction format and the assembler description from
disp8 to disp10 are as follows:
disp8 → dir + disp8:Each disp is a code extension
disp9 → dir = disp9>>1:Each disp is a code extension
disp10 → dir = disp10>>2:Each disp is a code extension
• Resource instructions (2 instructions)
Mnemonic
Type
OP
Cycle N Z V C
Operation
Remarks
LDRES
@Ri+,
#u4
C
BC
a
– – – – (Ri) → u4 resource
Ri + = 4
u4: Channel number
STRES
#u4,
@Ri+
C
BD
a
– – – – u4 resource → (Ri)
Ri + = 4
u4: Channel number
• Co-processor instructions (4 instructions)
Mnemonic
COPOP
COPLD
COPST
COPSV
114
#u4, #CC, CRj, CRi
#u4, #CC, Rj, CRi
#u4, #CC, CRj, Ri
#u4, #CC, CRj, Ri
Type
OP
E
E
E
E
9F – C
9F – D
9F – E
9F – F
Cycle N Z V C
2+a
1 + 2a
1 + 2a
1 + 2a
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Operation
Calculation
Rj → CRi
CRj → Ri
CRj → Ri
Remarks
No error traps
MB91133/MB91F133
• Other instructions (16 instructions)
Type
OP
NOP
E
9F – A
1
– – – – No changes
ANDCCR #u8
ORCCR #u8
D
D
83
93
c
c
C C C C CCR and u8 → CCR
C C C C CCR or u8 → CCR
STILM
#u8
D
87
1
– – – – i8 → ILM
Set ILM immediate
value
ADDSP
#s10
D
A3
1
– – – – R15 + = s10
ADD SP instruction
EXTSB
EXTUB
EXTSH
EXTUH
Ri
Ri
Ri
Ri
E
E
E
E
97 – 8
97 – 9
97 – A
97 – B
1
1
1
1
–
–
–
–
LDM0
(reglist)
D
8C
*4
Load-multi R0 to R7
LDM1
(reglist)
D
8D
*4
* LDM
(reglist)
– – – – (R15) → reglist,
R15 increment
– – – – (R15) → reglist,
R15 increment
– – – – (R15 + +) → reglist,
STM0
(reglist)
D
8E
*
Store-multi R0 to R7
STM1
(reglist)
D
8F
*6
* STM2
(reglist)
*5
– – – – R15 decrement,
reglist → (R15)
– – – – R15 decrement,
reglist → (R15)
– – – – reglist → (R15 + +)
ENTER
#u10
*2
Mnemonic
LEAVE
XCHB
@Rj, Ri
*1
*3
Cycle N Z V C
–
6
–
–
–
–
–
–
–
–
–
–
–
–
–
Operation
Remarks
Sign extension 8 → 32 bits
Zero extension 8 → 32 bits
Sign extension 16 → 32 bits
Zero extension 16 → 32 bits
Load-multi R8 to R15
Load-multi R0 to R15
Store-multi R8 to R15
Store-multi R0 to R15
D
0F
1+a
– – – – R14 → (R15 – 4),
R15 – 4 → R14,
R15 – u10 → R15
Entrance processing
of function
E
9F – 9
b
– – – – R14 + 4 → R15,
(R15 – 4) → R14
Exit processing of
function
A
8A
2a
– – – – Ri → TEMP,
(Rj) → Ri,
TEMP → (Rj)
For SEMAFO
management
Byte data
*1: In the ADDSP instruction, the reference between u8 of TYPE-D in the instruction format and assembler
description s10 is as follows.
s10 → s8 = s10>>2
*2: In the ENTER instruction, the reference between i8 of TYPE-C in the instruction format and assembler
description u10 is as follows.
u10 → u8 = u10>>2
*3: If either of R0 to R7 is specified in reglist, assembler generates LDM0. If either of R8 to R15 is specified,
assembler generates LDM1. Both LDM0 and LDM1 may be generated.
*4: The number of cycles needed for execution of LDM0 (reglist) and LDM1 (reglist) is given by the following
calculation; a × (n – 1) + b + 1 when “n” is number of registers specified.
*5: If either of R0 to R7 is specified in reglist, assembler generates STM0. If either of R8 to R15 is specified,
assembler generates STM1. Both STM0 and STM1 may be generated.
*6: The number of cycles needed for execution of STM0 (reglist) and STM1 (reglist) is given by the following
calculation; a × n + 1 when “n” is number of registers specified.
115
MB91133/MB91F133
• 20-bit normal branch macro instructions
Mnemonic
Operation
Remarks
* CALL20
label20, Ri
Next instruction address → RP, label20 → PC
Ri: Temporary register
*1
* BRA20
* BEQ20
* BNE20
* BC20
* BNC20
* BN20
* BP20
* BV20
* BNV20
* BLT20
* BGE20
* BLE20
* BGT20
* BLS20
* BHI20
label20, Ri
label20, Ri
label20, Ri
label20, Ri
label20, Ri
label20, Ri
label20, Ri
label20, Ri
label20, Ri
label20, Ri
label20, Ri
label20, Ri
label20, Ri
label20, Ri
label20, Ri
label20 → PC
if (Z = = 1) then label20 → PC
ifs/Z = = 0
ifs/C = = 1
ifs/C = = 0
ifs/N = = 1
ifs/N = = 0
ifs/V = = 1
ifs/V = = 0
ifs/V xor N = = 1
ifs/V xor N = = 0
ifs/(V xor N) or Z = = 1
ifs/(V xor N) or Z = = 0
ifs/C or Z = = 1
ifs/C or Z = = 0
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
*2
*3
*3
*3
*3
*3
*3
*3
*3
*3
*3
*3
*3
*3
*3
*1: CALL20
(1) If label20 – PC – 2 is between –0x800 and +0x7fe, instruction is generated as follows;
CALL
label12
(2) If label20 – PC – 2 is outside of the range given in (1) or includes external reference symbol, instruction is
generated as follows;
LDI:20 #label20, Ri
CALL
@Ri
*2: BRA20
(1) If label20 – PC – 2 is between –0x100 and +0xfe, instruction is generated as follows;
BRA
label9
(2) If label20 – PC – 2 is outside of the range given in (1) or includes external reference symbol, instruction is
generated as follows;
LDI:20 #label20, Ri
JMP
@Ri
*3: Bcc20 (BEQ20 to BHI20)
(1) If label20 – PC – 2 is between –0x100 and +0xfe, instruction is generated as follows;
Bcc
label9
(2) If label20 – PC – 2 is outside of the range given in (1) or includes external reference symbol, instruction is
generated as follows;
Bxcc
false
xcc is a revolt condition of cc
LDI:20 #label20, Ri
JMP
@Ri
false:
116
MB91133/MB91F133
• 20-bit delayed branch macro instructions
Mnemonic
Operation
Remarks
* CALL20:D label20, Ri
Next instruction address + 2 → RP, label20 → PC
Ri: Temporary register
*1
* BRA20:D
* BEQ20:D
* BNE20:D
* BC20:D
* BNC20:D
* BN20:D
* BP20:D
* BV20:D
* BNV20:D
* BLT20:D
* BGE20:D
* BLE20:D
* BGT20:D
* BLS20:D
* BHI20:D
label20 → PC
if (Z = = 1) then label20 → PC
ifs/Z = = 0
ifs/C = = 1
ifs/C = = 0
ifs/N = = 1
ifs/N = = 0
ifs/V = = 1
ifs/V = = 0
ifs/V xor N = = 1
ifs/V xor N = = 0
ifs/(V xor N) or Z = = 1
ifs/(V xor N) or Z = = 0
ifs/C or Z = = 1
ifs/C or Z = = 0
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
*2
*3
*3
*3
*3
*3
*3
*3
*3
*3
*3
*3
*3
*3
*3
label20, Ri
label20, Ri
label20, Ri
label20, Ri
label20, Ri
label20, Ri
label20, Ri
label20, Ri
label20, Ri
label20, Ri
label20, Ri
label20, Ri
label20, Ri
label20, Ri
label20, Ri
*1: CALL20:D
(1) If label20 – PC – 2 is between –0x800 and +0x7fe, instruction is generated as follows;
CALL:D label12
(2) If label20 – PC – 2 is outside of the range given in (1) or includes external reference symbol, instruction is
generated as follows;
LDI:20 #label20, Ri
CALL:D @Ri
*2: BRA20:D
(1) If label20 – PC – 2 is between –0x100 and +0xfe, instruction is generated as follows;
BRA:D label9
(2) If label20 – PC – 2 is outside of the range given in (1) or includes external reference symbol, instruction is
generated as follows;
LDI:20 #label20, Ri
JMP:D @Ri
*3: Bcc20:D (BEQ20:D to BHI20:D)
(1) If label20 – PC – 2 is between –0x100 and +0xfe, instruction is generated as follows;
Bcc:D
label9
(2) If label20 – PC – 2 is outside of the range given in (1) or includes external reference symbol, instruction is
generated as follows;
Bxcc
false
xcc is a revolt condition of cc
LDI:20 #label20, Ri
JMP:D @Ri
false:
117
MB91133/MB91F133
• 32-bit normal macro branch instructions
Mnemonic
Operation
Remarks
* CALL32
label32, Ri
Next instruction address → RP, label32 → PC
Ri: Temporary register
*1
* BRA32
* BEQ32
* BNE32
* BC32
* BNC32
* BN32
* BP32
* BV32
* BNV32
* BLT32
* BGE32
* BLE32
* BGT32
* BLS32
* BHI32
label32, Ri
label32, Ri
label32, Ri
label32, Ri
label32, Ri
label32, Ri
label32, Ri
label32, Ri
label32, Ri
label32, Ri
label32, Ri
label32, Ri
label32, Ri
label32, Ri
label32, Ri
label32 → PC
if (Z = = 1) then label32 → PC
ifs/Z = = 0
ifs/C = = 1
ifs/C = = 0
ifs/N = = 1
ifs/N = = 0
ifs/V = = 1
ifs/V = = 0
ifs/V xor N = = 1
ifs/V xor N = = 0
ifs/(V xor N) or Z = = 1
ifs/(V xor N) or Z = = 0
ifs/C or Z = = 1
ifs/C or Z = = 0
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
*2
*3
*3
*3
*3
*3
*3
*3
*3
*3
*3
*3
*3
*3
*3
*1: CALL32
(1) If label32 – PC – 2 is between –0x800 and +0x7fe, instruction is generated as follows;
CALL
label12
(2) If label32 – PC – 2 is outside of the range given in (1) or includes external reference symbol, instruction is
generated as follows;
LDI:32 #label32, Ri
CALL
@Ri
*2: BRA32
(1) If label32 – PC – 2 is between –0x100 and +0xfe, instruction is generated as follows;
BRA
label9
(2) If label32 – PC – 2 is outside of the range given in (1) or includes external reference symbol, instruction is
generated as follows;
LDI:32 #label32, Ri
JMP
@Ri
*3: Bcc32 (BEQ32 to BHI32)
(1) If label32 – PC – 2 is between –0x100 and +0xfe, instruction is generated as follows;
Bcc
label9
(2) If label32 – PC – 2 is outside of the range given in (1) or includes external reference symbol, instruction is
generated as follows;
Bxcc
false
xcc is a revolt condition of cc
LDI:32 #label32, Ri
JMP
@Ri
false:
118
MB91133/MB91F133
• 32-bit delayed macro branch instructions
Mnemonic
Operation
Remarks
* CALL32:D label32, Ri
Next instruction address + 2 → RP, label32 → PC
Ri: Temporary register
*1
* BRA32:D
* BEQ32:D
* BNE32:D
* BC32:D
* BNC32:D
* BN32:D
* BP32:D
* BV32:D
* BNV32:D
* BLT32:D
* BGE32:D
* BLE32:D
* BGT32:D
* BLS32:D
* BHI32:D
label32 → PC
if (Z = = 1) then label32 → PC
ifs/Z = = 0
ifs/C = = 1
ifs/C = = 0
ifs/N = = 1
ifs/N = = 0
ifs/V = = 1
ifs/V = = 0
ifs/V xor N = = 1
ifs/V xor N = = 0
ifs/(V xor N) or Z = = 1
ifs/(V xor N) or Z = = 0
ifs/C or Z = = 1
ifs/C or Z = = 0
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
Ri: Temporary register
*2
*3
*3
*3
*3
*3
*3
*3
*3
*3
*3
*3
*3
*3
*3
label32, Ri
label32, Ri
label32, Ri
label32, Ri
label32, Ri
label32, Ri
label32, Ri
label32, Ri
label32, Ri
label32, Ri
label32, Ri
label32, Ri
label32, Ri
label32, Ri
label32, Ri
*1: CALL32:D
(1) If label32 – PC – 2 is between –0x800 and +0x7fe, instruction is generated as follows;
CALL:D label12
(2) If label32 – PC – 2 is outside of the range given in (1) or includes external reference symbol, instruction is
generated as follows;
LDI:32 #label32, Ri
CALL:D @Ri
*2: BRA32:D
(1) If label32 – PC – 2 is between –0x100 and +0xfe, instruction is generated as follows;
BRA:D label9
(2) If label32 – PC – 2 is outside of the range given in (1) or includes external reference symbol, instruction is
generated as follows;
LDI:32 #label32, Ri
JMP:D @Ri
*3: Bcc32:D (BEQ32:D to BHI32:D)
(1) If label32 – PC – 2 is between –0x100 and +0xfe, instruction is generated as follows;
Bcc:D
label9
(2) If label32 – PC – 2 is outside of the range given in (1) or includes external reference symbol, instruction is
generated as follows;
Bxcc
false
xcc is a revolt condition of cc
LDI:32 #label32, Ri
JMP:D @Ri
false:
119
MB91133/MB91F133
■ ORDERING INFORMATION
Part number
120
Package
MB91133PMT2-XXX
144-pin plastic LQFP
(FPT-144P-M08)
MB91133PBT-XXX
144-pin plastic FBGA
(BGA-144P-M01)
MB91F133PMT2
144-pin plastic LQFP
(FPT-144P-M08)
MB91F133PBT
144-pin plastic FBGA
(BGA-144P-M01)
MB91FV130CR-ES
299-pin ceramic PGA
(PGA-299)
Remarks
MB91133/MB91F133
■ PACKAGE DIMENSIONS
144-pin plastic FBGA
(BGA-144P-M01)
12.00±0.10(.472±.004)SQ
Note) Corner shape may differ from the diagram.
+0.20
+.008
1.25 –0.10 .049 –.004
(Mounting height)
0.38±0.10(.015±.004)
(Stand off)
10.40(.409)REF
0.80(.031)TYP
14
13
12
11
10
9
8
7
6
5
0.10(.004)
4
INDEX
3
2
1
P N M L K J H G F E D C B A
C0.80(.031)
C
144-Ø0.45±0.10
(144-Ø.018±.004)
0.08(.003)
M
1998 FUJITSU LIMITED B144001S-2C-2
Dimensions in mm (inches)
121
MB91133/MB91F133
144-pin plastic LQFP
(FPT-144P-M08)
1.70(.67)MAX
22.00±0.30(.866±.012)SQ
20.00±0.10(.787±.004)SQ
108
0(0)MIN
(STAND OFF)
73
109
72
17.50
(.686)
REF
21.00
(.827)
NOM
Details of "A" part
0.15(.006)
0.15(.006)
INDEX
0.15(.006)MAX
37
144
0.40(.016)MAX
"A"
LEAD No.
36
1
0.50(.0197)TYP
0.20±0.10
(.008±.004)
0.08(.003)
Details of "B" part
M
0.15±0.05
(.006±.002)
0
0.10(.004)
C
10˚
0.50±0.20(.020±.008)
"B"
1995 FUJITSU LIMITED F144019S-1C-2
Dimensions in mm (inches)
122
MB91133/MB91F133
FUJITSU LIMITED
For further information please contact:
Japan
FUJITSU LIMITED
Corporate Global Business Support Division
Electronic Devices
Shinjuku Dai-Ichi Seimei Bldg. 7-1,
Nishishinjuku 2-chome, Shinjuku-ku,
Tokyo 163-0721, Japan
Tel: +81-3-5322-3347
Fax: +81-3-5322-3386
http://edevice.fujitsu.com/
North and South America
FUJITSU MICROELECTRONICS, INC.
3545 North First Street,
San Jose, CA 95134-1804, U.S.A.
Tel: +1-408-922-9000
Fax: +1-408-922-9179
Customer Response Center
Mon. - Fri.: 7 am - 5 pm (PST)
Tel: +1-800-866-8608
Fax: +1-408-922-9179
http://www.fujitsumicro.com/
Europe
FUJITSU MICROELECTRONICS EUROPE GmbH
Am Siebenstein 6-10,
D-63303 Dreieich-Buchschlag,
Germany
Tel: +49-6103-690-0
Fax: +49-6103-690-122
http://www.fujitsu-fme.com/
Asia Pacific
FUJITSU MICROELECTRONICS ASIA PTE. LTD.
#05-08, 151 Lorong Chuan,
New Tech Park,
Singapore 556741
Tel: +65-281-0770
Fax: +65-281-0220
http://www.fmap.com.sg/
Korea
FUJITSU MICROELECTRONICS KOREA LTD.
1702 KOSMO TOWER, 1002 Daechi-Dong,
Kangnam-Gu,Seoul 135-280
Korea
Tel: +82-2-3484-7100
Fax: +82-2-3484-7111
F0101
 FUJITSU LIMITED Printed in Japan
All Rights Reserved.
The contents of this document are subject to change without notice.
Customers are advised to consult with FUJITSU sales
representatives before ordering.
The information and circuit diagrams in this document are
presented as examples of semiconductor device applications, and
are not intended to be incorporated in devices for actual use. Also,
FUJITSU is unable to assume responsibility for infringement of
any patent rights or other rights of third parties arising from the use
of this information or circuit diagrams.
The contents of this document may not be reproduced or copied
without the permission of FUJITSU LIMITED.
FUJITSU semiconductor devices are intended for use in standard
applications (computers, office automation and other office
equipments, industrial, communications, and measurement
equipments, personal or household devices, etc.).
CAUTION:
Customers considering the use of our products in special
applications where failure or abnormal operation may directly
affect human lives or cause physical injury or property damage, or
where extremely high levels of reliability are demanded (such as
aerospace systems, atomic energy controls, sea floor repeaters,
vehicle operating controls, medical devices for life support, etc.)
are requested to consult with FUJITSU sales representatives before
such use. The company will not be responsible for damages arising
from such use without prior approval.
Any semiconductor devices have inherently a certain rate of failure.
You must protect against injury, damage or loss from such failures
by incorporating safety design measures into your facility and
equipment such as redundancy, fire protection, and prevention of
over-current levels and other abnormal operating conditions.
If any products described in this document represent goods or
technologies subject to certain restrictions on export under the
Foreign Exchange and Foreign Trade Control Law of Japan, the
prior authorization by Japanese government should be required for
export of those products from Japan.