HOLTEK HT48C06

HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
Cost-Effective I/O Type 8-Bit MCU
Features
· Operating voltage:
· Buzzer driving pair and PFD supported
fSYS=4MHz: 2.2V~5.5V
fSYS=8MHz: 3.3V~5.5V
· HALT function and wake-up feature reduce power
consumption
· 13 bidirectional I/O lines
· Up to 0.5ms instruction cycle with 8MHz system clock
· An interrupt input shared with an I/O line
at VDD=5V
· 8-bit programmable timer/event counter with over-
· Allinstructionsinoneortwomachinecycles
flow interrupt and 8-stage prescaler
· 14-bit table read instruction
· On-chip crystal and RC oscillator
· Two-level subroutine nesting
· Watchdog Timer
· Bit manipulation instruction
· Program memory ROM:
· Powerful instructions:
512´14 for HT48R05A-1/HT48C05
1024´14 for HT48R06A-1/HT48C06
62 for HT48R05A-1/HT48C05
63 for HT48R06A-1/HT48C06
· Data memory RAM
· Low voltage reset function
32´8 for HT48R05A-1/HT48C05
64´8 for HT48R06A-1/HT48C06
· 16-pin SSOP package
18-pin DIP/SOP package
General Description
The advantages of low power consumption, I/O flexibility, timer functions, oscillator options, HALT and
wake-up functions, watchdog timer, buzzer driver, as
well as low cost, enhance the versatility of these devices
to suit a wide range of application possibilities such as
industrial control, consumer products, subsystem controllers, etc.
The HT48R05A-1/HT48C05 and HT48R06A-1/
HT48C06 are 8-bit high performance, RISC architecture microcontroller devices specifically designed for
cost-effective multiple I/O control product applications.
The mask version HT48C05 and HT48C06 are fully pin
and functionally compatible with the OTP version
HT48R05A-1 and HT48R06A-1 devices.
Block Diagram
IN T /P C 0
In te rru p t
C ir c u it
T M R C
S T A C K 0
P ro g ra m
R O M
S T A C K 1
P ro g ra m
C o u n te r
IN T C
M
T M R
U
P r e s c a le r
P C 0
In s tr u c tio n
R e g is te r
M
M P
U
X
D A T A
M e m o ry
W D T S
W D T P r e s c a le r
P B C
S T A T U S
P A C
Rev. 1.10
U
fS
Y S
/4
X
R C
O S C
P C 0 ~ P C 1
S
S
C 1
P O R T B
P B
S h ifte r
T im in g
G e n e ra to r
O S
R E
V D
V S
M
B Z /B Z
A L U
O S C 2
W D T
P O R T C
P C
M U X
Y S
P C 1
P C C
In s tr u c tio n
D e c o d e r
fS
T M R /P C 1
X
P A
A C C
P O R T A
P B 0 ~ P B 2
P A 0 ~ P A 7
D
1
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
Pin Assignment
P A 3
1
1 6
P A 3
1
1 8
P A 4
P A 4
P A 2
2
1 7
P A 5
P A 2
2
1 5
P A 5
P A 1
3
1 6
P A 6
P A 1
3
1 4
P A 6
P A 0
4
1 5
P A 7
P A 0
4
1 3
P A 7
P B 2
5
1 4
O S C 2
P B 0 /B Z
5
1 2
O S C 2
P B 1 /B Z
6
1 3
O S C 1
V S S
6
1 1
O S C 1
P B 0 /B Z
7
1 2
V D D
P C 0 /IN T
7
1 0
V D D
V S S
8
1 1
R E S
P C 1 /T M R
8
9
R E S
P C 0 /IN T
9
1 0
P C 1 /T M R
H T 4 8 R 0 5 A -1 /H T 4 8 C 0 5
H T 4 8 R 0 6 A -1 /H T 4 8 C 0 6
1 6 S S O P -A
H T 4 8 R 0 5 A -1 /H T 4 8 C 0 5
H T 4 8 R 0 6 A -1 /H T 4 8 C 0 6
1 8 D IP -A /S O P -A
Pad Assignment
P A 1
P A 2
P A 3
P A 4
P A 5
P A 6
1 8
1 7
1 6
1 5
1 4
1 3
1
P B 2
2
P B 1 /B Z
3
(0 ,0 )
P A 0
1 2
1 1
9
O S C 2
1 0
O S C 1
8
V D D
V S S
7
R E S
P B 0 /B Z
6
P C 1 /T M R
5
P C 0 /IN T
4
P A 7
* The IC substrate should be connected to VSS in the PCB layout artwork.
Pad Description
Pad Name
PA0~PA7
I/O
Options
Description
I/O
Pull-high*
Wake-up
Bidirectional 8-bit input/output port. Each bit can be configured as wake-up
input by options. Software instructions determine the CMOS output or
Schmitt trigger input with a pull-high resistor (determined by pull-high options).
Bidirectional 3-bit input/output port. Software instructions determine the
CMOS output or Schmitt trigger input with a pull-high resistor (determined by
pull-high options).
The PB0 and PB1 are pin-shared with the BZ and BZ, respectively. Once the
PB0 and PB1 are selected as buzzer driving outputs, the output signals come
from an internal PFD generator (shared with a timer/event counter).
PB0/BZ
PB1/BZ
PB2
I/O
Pull-high*
I/O or BZ/BZ
VSS
¾
¾
PC0/INT
PC1/TMR
Rev. 1.10
I/O
Pull-high*
Negative power supply, ground
Bidirectional I/O lines. Software instructions determine the CMOS output or
Schmitt trigger input with a pull-high resistor (determined by pull-high options). The external interrupt and timer input are pin-shared with the PC0 and
PC1, respectively. The external interrupt input is activated on a high to low
transition.
2
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
Pad Name
I/O
Options
Description
RES
I
¾
Schmitt trigger reset input. Active low
VDD
¾
¾
Positive power supply
OSC1
OSC2
I
O
Crystal
or RC
OSC1, OSC2 are connected to an RC network or Crystal (determined by options) for the internal system clock. In the case of RC operation, OSC2 is the
output terminal for 1/4 system clock.
* All pull-high resistors are controlled by an option bit.
Absolute Maximum Ratings
Supply Voltage ...........................VSS-0.3V to VSS+6.0V
Storage Temperature ............................-50°C to 125°C
Input Voltage..............................VSS-0.3V to VDD+0.3V
Operating Temperature...........................-40°C to 85°C
Note: These are stress ratings only. Stresses exceeding the range specified under ²Absolute Maximum Ratings² may
cause substantial damage to the device. Functional operation of this device at other conditions beyond those
listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability.
D.C. Characteristics
Symbol
Parameter
Ta=25°C
Test Conditions
VDD
Conditions
Min.
Typ.
Max.
Unit
¾
fSYS=4MHz
2.2
¾
5.5
V
¾
fSYS=8MHz
3.3
¾
5.5
V
¾
0.6
1.5
mA
¾
2
4
mA
¾
0.8
1.5
mA
¾
2.5
4
mA
¾
3
5
mA
¾
¾
5
mA
¾
¾
10
mA
¾
¾
1
mA
¾
¾
2
mA
¾
0
¾
0.3VDD
V
¾
¾
0.7VDD
¾
VDD
V
Input Low Voltage (RES)
¾
¾
0
¾
0.4VDD
V
VIH2
Input High Voltage (RES)
¾
¾
0.9VDD
¾
VDD
V
VLVR
Low Voltage Reset
¾
LVR enabled
2.7
3.0
3.3
V
4
8
¾
mA
10
20
¾
mA
-2
-4
¾
mA
-5
-10
¾
mA
VDD
Operating Voltage
IDD1
Operating Current (Crystal OSC)
IDD2
Operating Current (RC OSC)
IDD3
Operating Current (Crystal OSC)
ISTB1
Standby Current (WDT Enabled)
ISTB2
Standby Current (WDT Disabled)
VIL1
Input Low Voltage for I/O Ports,
TMR and INT
¾
VIH1
Input High Voltage for I/O Ports,
TMR and INT
VIL2
3V
5V
3V
5V
No load, fSYS=4MHz
No load, fSYS=8MHz
3V
No load, system HALT
5V
3V
No load, system HALT
5V
3V
IOL
I/O Port Sink Current
IOH
I/O Port Source Current
RPH
Pull-high Resistance
Rev. 1.10
5V
No load, fSYS=4MHz
5V
3V
5V
VOL=0.1VDD
VOH=0.9VDD
3V
¾
20
60
100
kW
5V
¾
10
30
50
kW
3
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
A.C. Characteristics
Symbol
fSYS1
fSYS2
fTIMER
Parameter
System Clock (Crystal OSC)
System Clock (RC OSC)
Timer I/P Frequency (TMR)
tWDTOSC Watchdog Oscillator Period
Ta=25°C
Test Conditions
Conditions
VDD
Min.
Typ.
Max.
Unit
¾
2.2V~5.5V
400
¾
4000
kHz
¾
3.3V~5.5V
400
¾
8000
kHz
¾
2.2V~5.5V
400
¾
4000
kHz
¾
3.3V~5.5V
400
¾
8000
kHz
¾
2.2V~5.5V
0
¾
4000
kHz
¾
3.3V~5.5V
0
¾
8000
kHz
3V
¾
45
90
180
ms
5V
¾
32
65
130
ms
11
23
46
ms
8
17
33
ms
3V
tWDT1
Watchdog Time-out Period (RC)
tWDT2
Watchdog Time-out Period
(System Clock)
¾
Without WDT prescaler
¾
1024
¾
tSYS
tRES
External Reset Low Pulse Width
¾
¾
1
¾
¾
ms
tSST
System Start-up Timer Period
¾
¾
1024
¾
tSYS
tINT
Interrupt Pulse Width
¾
1
¾
¾
ms
Rev. 1.10
Without WDT prescaler
5V
Wake-up from HALT
¾
4
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
Functional Description
Execution Flow
incremented by one. The program counter then points to
the memory word containing the next instruction code.
The system clock for the microcontroller is derived from
either a crystal or an RC oscillator. The system clock is
internally divided into four non-overlapping clocks. One
instruction cycle consists of four system clock cycles.
When executing a jump instruction, conditional skip execution, loading PCL register, subroutine call, initial reset, internal interrupt, external interrupt or return from
subroutine, the PC manipulates the program transfer by
loading the address corresponding to each instruction.
Instruction fetching and execution are pipelined in such
a way that a fetch takes an instruction cycle while decoding and execution takes the next instruction cycle.
However, the pipelining scheme causes each instruction to effectively execute in a cycle. If an instruction
changes the program counter, two cycles are required to
complete the instruction.
The conditional skip is activated by instructions. Once
the condition is met, the next instruction, fetched during
the current instruction execution, is discarded and a
dummy cycle replaces it to get the proper instruction.
Otherwise proceed with the next instruction.
The lower byte of the program counter (PCL) is a readable and writable register (06H). Moving data into the
PCL performs a short jump. The destination will be
within 256 locations.
Program Counter - PC
The program counter (PC) controls the sequence in
which the instructions stored in program ROM are executed and its contents specify full range of program
memory.
When a control transfer takes place, an additional
dummy cycle is required.
After accessing a program memory word to fetch an instruction code, the contents of the program counter are
S y s te m
C lo c k
T 1
T 2
T 3
T 4
T 1
T 2
T 3
T 4
T 1
T 2
T 3
T 4
O S C 2 ( R C o n ly )
P C
P C
P C + 1
F e tc h IN S T (P C )
E x e c u te IN S T (P C -1 )
P C + 2
F e tc h IN S T (P C + 1 )
E x e c u te IN S T (P C )
F e tc h IN S T (P C + 2 )
E x e c u te IN S T (P C + 1 )
Execution Flow
Mode
Program Counter
*9
*8
*7
*6
*5
*4
*3
*2
*1
*0
Initial Reset
0
0
0
0
0
0
0
0
0
0
External Interrupt
0
0
0
0
0
0
0
1
0
0
Timer/Event Counter Overflow
0
0
0
0
0
0
1
0
0
0
Loading PCL
*9
*8
@7
@6
@5
@4
@3
@2
@1
@0
Jump, Call Branch
#9
#8
#7
#6
#5
#4
#3
#2
#1
#0
Return from Subroutine
S9
S8
S7
S6
S5
S4
S3
S2
S1
S0
Skip
PC+2
Program Counter
Note: *9~*0: Program Counter bits
S9~S0: Stack register bits
#9~#0: Instruction code bits
@7~@0: PCL bits
For HT48R05A-1/HT48C05, the Program Counter is 9 bits wide, i.e. from *8~*0
For HT48R06A-1/HT48C06, the Program Counter is 10 bits wide, i.e. from *9~*0
Rev. 1.10
5
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
· Table location
Program Memory - ROM
The program memory is used to store the program instructions which are to be executed. It also contains
data, table, and interrupt entries, and is organized into
512´14 bits (HT48R05A-1/HT48C05) or 1024´14 bits
(HT48R06A-1/HT48C06), addressed by the program
counter and table pointer.
Any location in the program memory can be used as
look-up tables. The instructions ²TABRDC [m]² (the
current page, 1 page=256 words) and ²TABRDL [m]²
(the last page; However this statement is not valid for
the HT48R05A-1/HT48C05 devices) transfer the contents of the lower-order byte to the specified data
memory, and the higher-order byte to TBLH (08H).
Only the destination of the lower-order byte in the table is well-defined, the other bits of the table word are
transferred to the lower portion of TBLH, and the remaining 2 bits are read as ²0². The Table Higher-order
byte register (TBLH) is read only. The table pointer
(TBLP) is a read/write register (07H), which indicates
the table location. Before accessing the table, the location must be placed in TBLP. The TBLH is read only
and cannot be restored. If the main routine and the
ISR (Interrupt Service Routine) both employ the table
read instruction, the contents of the TBLH in the main
routine are likely to be changed by the table read instruction used in the ISR. Errors can occur. In other
words, using the table read instruction in the main routine and the ISR simultaneously should be avoided.
However, if the table read instruction has to be applied
in both the main routine and the ISR, the interrupt is
supposed to be disabled prior to the table read in-
Certain locations in the program memory are reserved
for special usage:
· Location 000H
This area is reserved for program initialization. After
chip reset, the program always begins execution at location 000H.
· Location 004H
This area is reserved for the external interrupt service
program. If the INT input pin is activated, the interrupt
is enabled and the stack is not full, the program begins
execution at location 004H.
· Location 008H
This area is reserved for the timer/event counter interrupt service program. If a timer interrupt results from a
timer/event counter overflow, and if the interrupt is enabled and the stack is not full, the program begins execution at location 008H.
H T 4 8 R 0 5 A -1 /H T 4 8 C 0 5
H T 4 8 R 0 6 A -1 /H T 4 8 C 0 6
In itia liz a tio n
V e c to r
In itia liz a tio n
V e c to r
E x te rn a l
In te rru p t V e c to r
E x te rn a l
In te rru p t V e c to r
T im e r /C o u n te r
In te rru p t V e c to r
T im e r /C o u n te r
In te rru p t V e c to r
0 0 0 H
0 0 4 H
0 0 8 H
1 F F H
2 0 0 H
N o t Im p le m e n te d
3 F F H
1 4 b its
1 4 b its
Program Memory
Instruction
Table Location
*9
*8
*7
*6
*5
*4
*3
*2
*1
*0
TABRDC [m]
P9
P8
@7
@6
@5
@4
@3
@2
@1
@0
TABRDL [m]
1
1
@7
@6
@5
@4
@3
@2
@1
@0
Table Location
Note: *9~*0: Table location bits
P9, P8: Current program counter bits
@7~@0: Table pointer bits
For HT48R05A-1/HT48C05, the table address location is 9 bits, i.e. from *8~*0
For HT48R06A-1/HT48C06, the table address location is 10 bits, i.e. from *9~*0
Rev. 1.10
6
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
7FH (HT48R06A-1/ HT48C06), is used for data and
control information under instruction commands.
struction. It will not be enabled until the TBLH has
been backed up. All table related instructions require
two cycles to complete the operation. These areas
may function as normal program memory depending
upon the requirements.
All of the data memory areas can handle arithmetic,
logic, increment, decrement and rotate operations directly. Except for some dedicated bits, each bit in the
data memory can be set and reset by ²SET [m].i² and
²CLR [m].i². They are also indirectly accessible through
memory pointer register (MP;01H).
Stack Register - STACK
This is a special part of the memory which is used to
save the contents of the program counter (PC) only. The
stack is organized into 2 levels and is neither part of the
data nor part of the program space, and is neither readable nor writable. The activated level is indexed by the
stack pointer (SP) and is neither readable nor writeable.
At a subroutine call or interrupt acknowledgment, the
contents of the program counter are pushed onto the
stack. At the end of a subroutine or an interrupt routine,
signaled by a return instruction (RET or RETI), the program counter is restored to its previous value from the
stack. After a chip reset, the SP will point to the top of the
stack.
Indirect Addressing Register
Location 00H is an indirect addressing register that is
not physically implemented. Any read/write operation of
[00H] accesses data memory pointed to by MP (01H).
Reading location 00H itself indirectly will return the result 00H. Writing indirectly results in no operation.
H T 4 8 R 0 5 A -1 /H T 4 8 C 0 5
0 0 H
In d ir e c t A d d r e s s in g R e g is te r
0 1 H
M P
0 2 H
0 3 H
If the stack is full and a non-masked interrupt takes
place, the interrupt request flag will be recorded but the
acknowledgment will be inhibited. When the stack
pointer is decremented (by RET or RETI), the interrupt
will be serviced. This feature prevents stack overflow allowing the programmer to use the structure more easily.
In a similar case, if the stack is full and a ²CALL² is subsequently executed, stack overflow occurs and the first
entry will be lost (only the most recent 2 return addresses are stored).
0 4 H
0 5 H
P C L
0 7 H
T B L P
0 8 H
T B L H
0 9 H
W D T S
0 A H
S T A T U S
0 B H
IN T C
0 C H
Data Memory - RAM
0 D H
T M R
0 E H
T M R C
S p e c ia l P u r p o s e
D A T A M E M O R Y
0 F H
The data memory is designed with 49´8 bits
(HT48R05A-1/HT48C05) or 81´8 bits (HT48R06A-1/
HT48C06). The data memory is divided into two functional groups: special function registers and general
purpose data memory 32´8 (HT48R05A-1/HT48C05)
or 64´8 (HT48R06A-1/HT48C06). Most are read/write,
but some are read only.
1 0 H
The special function registers include the indirect add re s s ing r egi s t er ( 0 0 H ) , t i m er / e v en t co u n t e r
(TMR;0DH), timer/event counter control register
(TMRC;0EH), program counter lower-order byte register (PCL;06H), memory pointer register (MP;01H), accumulator (ACC;05H), table pointer (TBLP;07H), table
higher-order byte register (TBLH;08H), status register
(STATUS;0AH), interrupt control register (INTC;0BH),
Watchdog Timer option setting register (WDTS;09H),
I/O registers (PA;12H, PB;14H, PC;16H) and I/O control
registers (PAC;13H, PBC;15H, PCC;17H). The remaining space before the 60H (HT48R05A-1/ HT48C05) or
40H (HT48R06A-1/ HT48C06) is reserved for future expanded usage and reading these locations will get
²00H². The general purpose data memory, addressed
from 60H to 7FH (HT48R05A-1/ HT48C05) or 40H to
1 8 H
Rev. 1.10
A C C
0 6 H
1 1 H
1 2 H
P A
1 3 H
P A C
1 4 H
P B
1 5 H
P B C
1 6 H
P C
1 7 H
P C C
1 9 H
: U n u s e d
1 A H
R e a d a s "0 0 "
1 B H
1 C H
1 D H
1 E H
1 F H
2 0 H
5 F H
6 0 H
G e n e ra l P u rp o s e
D A T A M E M O R Y
(3 2 B y te s )
7 F H
RAM Mapping for HT48R05A-1/HT48C05
7
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
· Rotation (RL, RR, RLC, RRC)
H T 4 8 R 0 6 A -1 /H T 4 8 C 0 6
0 0 H
In d ir e c t A d d r e s s in g R e g is te r
0 1 H
M P
· Increment and Decrement (INC, DEC)
· Branch decision (SZ, SNZ, SIZ, SDZ ....)
0 2 H
The ALU not only saves the results of a data operation
but also changes the status register.
0 3 H
0 4 H
0 5 H
A C C
0 6 H
P C L
0 7 H
T B L P
0 8 H
T B L H
0 9 H
W D T S
0 A H
S T A T U S
0 B H
IN T C
0 C H
0 D H
T M R
0 E H
T M R C
Status Register - STATUS
This 8-bit register (0AH) contains the zero flag (Z), carry
flag (C), auxiliary carry flag (AC), overflow flag (OV),
power down flag (PDF), and watchdog time-out flag
(TO). It also records the status information and controls
the operation sequence.
S p e c ia l P u r p o s e
D A T A M E M O R Y
With the exception of the TO and PDF flags, bits in the
status register can be altered by instructions like most
other registers. Any data written into the status register
will not change the TO or PDF flag. In addition operations related to the status register may give different results from those intended. The TO flag can be affected
only by system power-up, a WDT time-out or executing
the ²CLR WDT² or ²HALT² instruction. The PDF flag
can be affected only by executing the ²HALT² or ²CLR
WDT² instruction or a system power-up.
0 F H
1 0 H
1 1 H
1 2 H
P A
1 3 H
P A C
1 4 H
P B
1 5 H
P B C
1 6 H
P C
1 7 H
P C C
The Z, OV, AC and C flags generally reflect the status of
the latest operations.
1 8 H
1 9 H
: U n u s e d
1 A H
R e a d a s "0 0 "
1 B H
In addition, on entering the interrupt sequence or executing the subroutine call, the status register will not be
pushed onto the stack automatically. If the contents of
the status are important and if the subroutine can corrupt the status register, precautions must be taken to
save it properly.
1 C H
1 D H
1 E H
1 F H
2 0 H
Interrupt
3 F H
4 0 H
The device provides an external interrupt and internal
timer/event counter interrupts. The Interrupt Control
Register (INTC;0BH) contains the interrupt control bits
to set the enable or disable and the interrupt request
flags.
G e n e ra l P u rp o s e
D A T A M E M O R Y
(6 4 B y te s )
7 F H
RAM Mapping for HT48R06A-1/HT48C06
Once an interrupt subroutine is serviced, all the other interrupts will be blocked (by clearing the EMI bit). This
scheme may prevent any further interrupt nesting. Other
interrupt requests may happen during this interval but
only the interrupt request flag is recorded. If a certain interrupt requires servicing within the service routine, the
EMI bit and the corresponding bit of INTC may be set to
allow interrupt nesting. If the stack is full, the interrupt request will not be acknowledged, even if the related interrupt is enabled, until the SP is decremented. If
immediate service is desired, the stack must be prevented from becoming full.
The memory pointer register MP (01H) is a 7-bit register.
The bit 7 of MP is undefined and reading will return the
result ²1². Any writing operation to MP will only transfer
the lower 7-bit data to MP.
Accumulator
The accumulator is closely related to ALU operations. It
is also mapped to location 05H of the data memory and
can carry out immediate data operations. The data
movement between two data memory locations must
pass through the accumulator.
All these kinds of interrupts have a wake-up capability.
As an interrupt is serviced, a control transfer occurs by
pushing the program counter onto the stack, followed by
a branch to a subroutine at specified location in the program memory. Only the program counter is pushed onto
the stack. If the contents of the register or status register
Arithmetic and Logic Unit - ALU
This circuit performs 8-bit arithmetic and logic operations. The ALU provides the following functions:
· Arithmetic operations (ADD, ADC, SUB, SBC, DAA)
· Logic operations (AND, OR, XOR, CPL)
Rev. 1.10
8
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
or ²RETI² may be invoked. RETI will set the EMI bit to enable an interrupt service, but RET will not.
(STATUS) are altered by the interrupt service program
which corrupts the desired control sequence, the contents should be saved in advance.
Interrupts, occurring in the interval between the rising
edges of two consecutive T2 pulses, will be serviced on
the latter of the two T2 pulses, if the corresponding interrupts are enabled. In the case of simultaneous requests
the following table shows the priority that is applied.
These can be masked by resetting the EMI bit.
External interrupts are triggered by a high to low transition of INT and the related interrupt request flag (EIF; bit
4 of INTC) will be set. When the interrupt is enabled, the
stack is not full and the external interrupt is active, a subroutine call to location 04H will occur. The interrupt request flag (EIF) and EMI bits will be cleared to disable
other interrupts.
No.
The internal timer/event counter interrupt is initialized by
setting the timer/event counter interrupt request flag
(TF; bit 5 of INTC), caused by a timer overflow. When
the interrupt is enabled, the stack is not full and the TF
bit is set, a subroutine call to location 08H will occur. The
related interrupt request flag (TF) will be reset and the
EMI bit cleared to disable further interrupts.
Interrupt Source
Priority Vector
a
External Interrupt
1
04H
b
Timer/Event Counter Overflow
2
08H
The timer/event counter interrupt request flag (TF), external interrupt request flag (EIF), enable timer/event
counter bit (ETI), enable external interrupt bit (EEI) and
enable master interrupt bit (EMI) constitute an interrupt
control register (INTC) which is located at 0BH in the
data memory. EMI, EEI, ETI are used to control the enabling/disabling of interrupts. These bits prevent the requested interrupt from being serviced. Once the
interrupt request flags (TF, EIF) are set, they will remain
in the INTC register until the interrupts are serviced or
cleared by a software instruction.
During the execution of an interrupt subroutine, other interrupt acknowledgments are held until the ²RETI²
instruction is executed or the EMI bit and the related interrupt control bit are set to 1 (of course, if the stack is
not full). To return from the interrupt subroutine, ²RET²
Labels
Bits
Function
C
0
C is set if the operation results in a carry during an addition operation or if a borrow does not take
place during a subtraction operation; otherwise C is cleared. C is also affected by a rotate
through carry instruction.
AC
1
AC is set if the operation results in a carry out of the low nibbles in addition or no borrow from the
high nibble into the low nibble in subtraction; otherwise AC is cleared.
Z
2
Z is set if the result of an arithmetic or logic operation is zero; otherwise Z is cleared.
OV
3
OV is set if the operation results in a carry into the highest-order bit but not a carry out of the
highest-order bit, or vice versa; otherwise OV is cleared.
PDF
4
PDF is cleared by system power-up or executing the ²CLR WDT² instruction. PDF is set by executing the ²HALT² instruction.
TO
5
TO is cleared by system power-up or executing the ²CLR WDT² or ²HALT² instruction. TO is set
by a WDT time-out.
¾
6
Unused bit, read as ²0²
¾
7
Unused bit, read as ²0²
Status Register
Register
INTC
(0BH)
Bit No.
Label
0
EMI
Controls the master (global) interrupt (1= enabled; 0= disabled)
Function
1
EEI
Controls the external interrupt (1= enabled; 0= disabled)
2
ETI
Controls the timer/event counter interrupt (1= enabled; 0= disabled)
3
¾
Unused bit, read as ²0²
4
EIF
External interrupt request flag (1= active; 0= inactive)
5
TF
Internal timer/event counter request flag (1= active; 0= inactive)
6
¾
Unused bit, read as ²0²
7
¾
Unused bit, read as ²0²
INTC Register
Rev. 1.10
9
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
tor can also be connected between OSC1 and OSC2 to
get a frequency reference, but two external capacitors in
OSC1 and OSC2 are required (If the oscillating frequency is less than 1MHz).
It is recommended that a program does not use the
²CALL subroutine² within the interrupt subroutine. Interrupts often occur in an unpredictable manner or need
to be serviced immediately in some applications. If only
one stack is left and enabling the interrupt is not well
controlled, the original control sequence will be damaged once the ²CALL² operates in the interrupt subroutine.
The WDT oscillator is a free running on-chip RC oscillator, and no external components are required. Even if
the system enters the power down mode, the system
clock is stopped, but the WDT oscillator still works with a
period of approximately 65ms@5V. The WDT oscillator
can be disabled by options to conserve power.
Oscillator Configuration
There are two oscillator circuits in the microcontroller.
V
O S C 1
4 7 0 p F
O S C 2
C r y s ta l O s c illa to r
Watchdog Timer - WDT
D D
fS Y S /4
N M O S O p e n D r a in
The clock source of WDT is implemented by a dedicated
RC oscillator (WDT oscillator) or instruction clock (system clock divided by 4), decided by options. This timer is
designed to prevent a software malfunction or sequence
from jumping to an unknown location with unpredictable
results. The Watchdog Timer can be disabled by an option. If the Watchdog Timer is disabled, all the executions related to the WDT result in no operation.
O S C 1
O S C 2
R C O s c illa to r
System Oscillator
Once the internal WDT oscillator (RC oscillator with a
period of 65ms@5V normally) is selected, it is first divided by 256 (8-stage) to get the nominal time-out period of approximately 17ms@5V. This time-out period
may vary with temperatures, VDD and process variations. By invoking the WDT prescaler, longer time-out
periods can be realized. Writing data to WS2, WS1,
WS0 (bit 2,1,0 of the WDTS) can give different time-out
periods. If WS2, WS1, and WS0 are all equal to 1, the division ratio is up to 1:128, and the maximum time-out
period is 2.1s@5V seconds. If the WDT oscillator is disabled, the WDT clock may still come from the instruction
clock and operate in the same manner except that in the
HALT state the WDT may stop counting and lose its protecting purpose. In this situation the logic can only be restarted by external logic. The high nibble and bit 3 of the
WDTS are reserved for user¢s defined flags, which can
be used to indicate some specified status.
Both are designed for system clocks, namely the RC oscillator and the Crystal oscillator, which are determined
by the options. No matter what oscillator type is selected, the signal provides the system clock. The HALT
mode stops the system oscillator and ignores an external signal to conserve power.
If an RC oscillator is used, an external resistor between
OSC1 and VDD is required and the resistance must
range from 24kW to 1MW. The system clock, divided by
4, is available on OSC2, which can be used to synchronize external logic. The RC oscillator provides the most
cost effective solution. However, the frequency of oscillation may vary with VDD, temperatures and the chip itself due to process variations. It is, therefore, not
suitable for timing sensitive operations where an accurate oscillator frequency is desired.
If the Crystal oscillator is used, a crystal across OSC1
and OSC2 is needed to provide the feedback and phase
shift required for the oscillator, and no other external
components are required. Instead of a crystal, a resonaS y s te m
If the device operates in a noisy environment, using the
on-chip RC oscillator (WDT OSC) is strongly recommended, since the HALT will stop the system clock.
C lo c k /4
W D T P r e s c a le r
O p tio n
S e le c t
8 - b it C o u n te r
W D T
O S C
7 - b it C o u n te r
8 -to -1 M U X
W S 0 ~ W S 2
W D T T im e - o u t
Watchdog Timer
Rev. 1.10
10
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
WS2
WS1
WS0
Division Ratio
0
0
0
1:1
0
0
1
1:2
0
1
0
1:4
0
1
1
1:8
1
0
0
1:16
1
0
1
1:32
1
1
0
1:64
1
1
1
1:128
The port A wake-up and interrupt methods can be considered as a continuation of normal execution. Each bit
in port A can be independently selected to wake up the
device by the options. Awakening from an I/O port stimulus, the program will resume execution of the next instruction. If it is awakening from an interrupt, two
sequences may happen. If the related interrupt is disabled or the interrupt is enabled but the stack is full, the
program will resume execution at the next instruction. If
the interrupt is enabled and the stack is not full, the regular interrupt response takes place. If an interrupt request
flag is set to ²1² before entering the HALT mode, the
wake-up function of the related interrupt will be disabled.
Once a wake-up event occurs, it takes 1024 tSYS (system clock period) to resume normal operation. In other
words, a dummy period will be inserted after wake-up. If
the wake-up results from an interrupt acknowledgment,
the actual interrupt subroutine execution will be delayed
by one or more cycles. If the wake-up results in the next
instruction execution, this will be executed immediately
after the dummy period is finished.
WDTS Register
The WDT overflow under normal operation will initialize
²chip reset² and set the status bit ²TO². But in the HALT
mode, the overflow will initialize a ²warm reset², and
only the PC and SP are reset to zero. To clear the contents of WDT (including the WDT prescaler), three
methods are adopted; external reset (a low level to
RES), software instruction and a ²HALT² instruction.
The software instruction include ²CLR WDT² and the
other set - ²CLR WDT1² and ²CLR WDT2². Of these
two types of instruction, only one can be active depending on the option - ²CLR WDT times selection option². If
the ²CLR WDT² is selected (i.e. CLRWDT times equal
one), any execution of the ²CLR WDT² instruction will
clear the WDT. In the case that ²CLR WDT1² and ²CLR
WDT2² are chosen (i.e. CLRWDT times equal two),
these two instructions must be executed to clear the
WDT; otherwise, the WDT may reset the chip as a result
of time-out.
To minimize power consumption, all the I/O pins should
be carefully managed before entering the HALT status.
Reset
There are three ways in which a reset can occur:
· RES reset during normal operation
· RES reset during HALT
· WDT time-out reset during normal operation
The WDT time-out during HALT is different from other
chip reset conditions, since it can perform a ²warm re set² that resets only the PC and SP, leaving the other circuits in their original state. Some registers remain unchanged during other reset conditions. Most registers
are reset to the ²initial condition² when the reset conditions are met. By examining the PDF and TO flags, the
program can distinguish between different ²chip resets².
Power Down Operation - HALT
The HALT mode is initialized by the ²HALT² instruction
and results in the following...
· The system oscillator will be turned off but the WDT
oscillator keeps running (if the WDT oscillator is selected).
TO PDF
· The contents of the on chip RAM and registers remain
unchanged.
· WDT and WDT prescaler will be cleared and re-
counted again (if the WDT clock is from the WDT oscillator).
· AlloftheI/Oportsmaintaintheiroriginalstatus.
· The PDF flag is set and the TO flag is cleared.
The system can leave the HALT mode by means of an
external reset, an interrupt, an external falling edge signal on port A or a WDT overflow. An external reset
causes a device initialization and the WDT overflow performs a ²warm reset². After the TO and PDF flags are
examined, the reason for chip reset can be determined.
The PDF flag is cleared by system power-up or executing the ²CLR WDT² instruction and is set when executing the ²HALT² instruction. The TO flag is set if the WDT
time-out occurs, and causes a wake-up that only resets
the PC and SP; the others keep their original status.
Rev. 1.10
RESET Conditions
0
0
RES reset during power-up
u
u
RES reset during normal operation
0
1
RES wake-up HALT
1
u
WDT time-out during normal operation
1
1
WDT wake-up HALT
Note: ²u² means ²unchanged²
To guarantee that the system oscillator is started and
stabilized, the SST (System Start-up Timer) provides an
extra-delay of 1024 system clock pulses when the system reset (power-up, WDT time-out or RES reset) or the
system awakes from the HALT state.
When a system reset occurs, the SST delay is added
during the reset period. Any wake-up from HALT will enable the SST delay.
11
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
H A L T
V D D
R E S
tS
R E S
C o ld
R e s e t
R e s e t
Reset Timing Chart
V
S S T
1 0 - b it R ip p le
C o u n te r
O S C 1
D D
S y s te m
0 .0 1 m F *
1 0 0 k W
R e s e t
Reset Configuration
R E S
The functional unit chip reset status are shown below.
1 0 k W
0 .1 m F *
Reset Circuit
Note:
R e s e t
W D T
S T
S S T T im e - o u t
C h ip
W a rm
²*² Make the length of the wiring, which is connected to the RES pin as short as possible, to
avoid noise interference.
An extra option load time delay is added during system
reset (power-up, WDT time-out at normal mode or RES
reset).
PC
000H
Interrupt
Disable
Prescaler
Clear
WDT
Clear. After master reset,
WDT begins counting
Timer/Event Counter
Off
Input/Output Ports
Input mode
SP
Points to the top of the stack
The states of the registers is summarized in the table.
Reset
(Power On)
WDT time-out
(Normal Operation)
RES Reset
(Normal Operation)
RES Reset
(HALT)
WDT Time-out
(HALT)*
TMR
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
uuuu uuuu
TMRC
00-0 1000
00-0 1000
00-0 1000
00-0 1000
uu-u uuuu
000H
000H
000H
000H
000H
MP
-xxx xxxx
-uuu uuuu
-uuu uuuu
-uuu uuuu
-uuu uuuu
ACC
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
TBLP
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
TBLH
--xx xxxx
--uu uuuu
--uu uuuu
--uu uuuu
--uu uuuu
STATUS
--00 xxxx
--1u uuuu
--uu uuuu
--01 uuuu
--11 uuuu
INTC
--00 -000
--00 -000
--00 -000
--00 -000
--uu -uuu
WDTS
0000 0111
0000 0111
0000 0111
0000 0111
uuuu uuuu
PA
1111 1111
1111 1111
1111 1111
1111 1111
uuuu uuuu
PAC
1111 1111
1111 1111
1111 1111
1111 1111
uuuu uuuu
PB
---- -111
---- -111
---- -111
---- -111
---- -uuu
PBC
---- -111
---- -111
---- -111
---- -111
---- -uuu
PC
---- --11
---- --11
---- --11
---- --11
---- --uu
PCC
---- --11
---- --11
---- --11
---- --11
---- --uu
Register
Program
Counter
Note:
²*² means ²warm reset²
²u² means ²unchanged²
²x² means ²unknown²
Rev. 1.10
12
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
Timer/Event Counter
The TM0, TM1 bits define the operating mode. The
event count mode is used to count external events,
which means the clock source comes from an external
(TMR) pin. The timer mode functions as a normal timer
with the clock source coming from the fINT clock. The
pulse width measurement mode can be used to count
the high or low level duration of the external signal
(TMR). The counting is based on the fINT clock.
A timer/event counter (TMR) is implemented in the
microcontroller. The timer/event counter contains an 8-bit
programmable count-up counter and the clock may come
from an external source or the system clock.
Using external clock input allows the user to count external events, measure time internals or pulse widths, or
generate an accurate time base. While using the internal clock allows the user to generate an accurate time
base.
In the event count or timer mode, once the timer/event
counter starts counting, it will count from the current
contents in the timer/event counter to FFH. Once overflow occurs, the counter is reloaded from the timer/event
counter preload register and generates the interrupt request flag (TF; bit 5 of INTC) at the same time.
The timer/event counter can generate PFD signal by using external or internal clock and PFD frequency is determine by the equation fINT/[2´(256-N)].
There are 2 registers related to the timer/event counter;
TMR ([0DH]), TMRC ([0EH]). Two physical registers are
mapped to TMR location; writing TMR makes the starting value be placed in the timer/event counter preload
register and reading TMR retrieves the contents of the
timer/event counter. The TMRC is a timer/event counter
control register, which defines some options.
fS
Y S
In the pulse width measurement mode with the TON
and TE bits equal to one, once the TMR has received a
transient from low to high (or high to low if the TE bits is
²0²) it will start counting until the TMR returns to the original level and resets the TON. The measured result will
remain in the timer/event counter even if the activated
8 - s ta g e P r e s c a le r
f IN
8 -1 M U X
P S C 2 ~ P S C 0
D a ta B u s
T
T M 1
T M 0
T M R
T im e r /E v e n t C o u n te r
P r e lo a d R e g is te r
R e lo a d
T E
T M 1
T M 0
T O N
P u ls e W id th
M e a s u re m e n t
M o d e C o n tro l
T im e r /E v e n t
C o u n te r
O v e r flo w
to In te rru p t
1 /2
B Z
B Z
Timer/Event Counter
Label
(TMRC)
PSC0~PSC2
Bits
0~2
Function
To define the prescaler stages, PSC2, PSC1, PSC0=
000: fINT=fSYS/2
001: fINT=fSYS/4
010: fINT=fSYS/8
011: fINT=fSYS/16
100: fINT=fSYS/32
101: fINT=fSYS/64
110: fINT=fSYS/128
111: fINT=fSYS/256
TE
3
To define the TMR active edge of the timer/event counter
(0=active on low to high; 1=active on high to low)
TON
4
To enable or disable timer counting
(0=disabled; 1=enabled)
5
Unused bit, read as ²0²
6
7
To define the operating mode
01=Event count mode (external clock)
10=Timer mode (internal clock)
11=Pulse width measurement mode
00=Unused
¾
TM0
TM1
TMRC Register
Rev. 1.10
13
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
transient occurs again. In other words, only one cycle
measurement can be done. Until setting the TON, the
cycle measurement will function again as long as it receives further transient pulse. Note that, in this operating mode, the timer/event counter starts counting not
according to the logic level but according to the transient
edges. In the case of counter overflows, the counter is
reloaded from the timer/event counter preload register
and issues the interrupt request just like the other two
modes. To enable the counting operation, the timer ON
bit (TON; bit 4 of TMRC) should be set to 1. In the pulse
width measurement mode, the TON will be cleared automatically after the measurement cycle is completed.
But in the other two modes the TON can only be reset by
instructions. The overflow of the timer/event counter is
one of the wake-up sources. No matter what the operation mode is, writing a 0 to ETI can disable the interrupt
service.
Input/Output Ports
There are 13 bidirectional input/output lines in the
microcontroller, labeled from PA to PC, which are
mapped to the data memory of [12H], [14H] and [16H]
respectively. All of these I/O ports can be used for input
and output operations. For input operation, these ports
are non-latching, that is, the inputs must be ready at the
T2 rising edge of instruction ²MOV A,[m]² (m=12H, 14H
or 16H). For output operation, all the data is latched and
remains unchanged until the output latch is rewritten.
Each I/O line has its own control register (PAC, PBC,
PCC) to control the input/output configuration. With this
control register, CMOS output or Schmitt trigger input
with or without pull-high resistor structures can be reconfigured dynamically (i.e. on-the-fly) under software
control. To function as an input, the corresponding latch
of the control register must write ²1². The input source
also depends on the control register. If the control register bit is ²1², the input will read the pad state. If the control register bit is ²0², the contents of the latches will
move to the internal bus. The latter is possible in the
²read-modify-write² instruction.
In the case of timer/event counter OFF condition, writing
data to the timer/event counter preload register will also
reload that data to the timer/event counter. But if the
timer/event counter is turned on, data written to it will
only be kept in the timer/event counter preload register.
The timer/event counter will still operate until overflow
occurs. When the timer/event counter (reading TMR) is
read, the clock will be blocked to avoid errors. As clock
blocking may results in a counting error, this must be
taken into consideration by the programmer.
For output function, CMOS is the only configuration.
These control registers are mapped to locations 13H,
15H and 17H.
After a chip reset, these input/output lines remain at high
levels or floating state (dependent on pull-high options).
Each bit of these input/output latches can be set or
cleared by ²SET [m].i² and ²CLR [m].i² (m=12H, 14H or
16H) instructions.
The bit0~2 of the TMRC can be used to define the
pre-scaling stages of the internal clock sources of the
timer/event counter. The definitions are as shown. The
overflow signal of the timer/event counter can be used
to generate PFD signals for buzzer driving.
Some instructions first input data and then follow the
output operations. For example, ²SET [m].i², ²CLR
V
C o n tr o l B it
D a ta B u s
P U
Q
D
Q
C K
W r ite C o n tr o l R e g is te r
D D
S
C h ip R e s e t
R e a d C o n tr o l R e g is te r
P A 0 ~ P A 7
P B 0 ~ P B 2
P C 0 ~ P C 1
D a ta B it
Q
D
Q
C K
W r ite D a ta R e g is te r
S
( P B 0 , P B 1 O n ly )
M
P B 0
E X T
M
R e a d D a ta R e g is te r
U
U
X
B Z E N
( P B 0 , P B 1 O n ly )
X
S y s te m W a k e -u p
( P A o n ly )
O P 0 ~ O P 7
IN T fo r P C 0 O n ly
T M R
fo r P C 1 O n ly
Input/Output Ports
Rev. 1.10
14
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
[m].i², ²CPL [m]², ²CPLA [m]² read the entire port states
into the CPU, execute the defined operations
(bit-operation), and then write the results back to the
latches or the accumulator.
The PC0 and PC1 are pin-shared with INT, TMR and
pins respectively.
It is recommended that unused or not bonded out I/O
lines should be set as output pins by software instruction
to avoid consuming power under input floating state.
Each line of port A has the capability of waking-up the
device. The highest 6-bit of port C and 5 bits of port B
are not physically implemented; on reading them a ²0² is
returned whereas writing then results in a no-operation.
See Application note.
Low Voltage Reset - LVR
The microcontroller provides low voltage reset circuit in
order to monitor the supply voltage of the device. If the
supply voltage of the device is within the range
0.9V~VLVR, such as changing a battery, the LVR will automatically reset the device internally.
There is a pull-high option available for all I/O lines.
Once the pull-high option is selected, all I/O lines have
pull-high resistors. Otherwise, the pull-high resistors are
absent. It should be noted that a non-pull-high I/O line
operating in input mode will cause a floating state.
The LVR includes the following specifications:
· The low voltage (0.9V~VLVR) has to remain in their
original state to exceed 1ms. If the low voltage state
does not exceed 1ms, the LVR will ignore it and do not
perform a reset function.
The PB0 and PB1 are pin-shared with BZ and BZ signal,
respectively. If the BZ/BZ option is selected, the output
signal in output mode of PB0/PB1 will be the PFD signal
generated by timer/event counter overflow signal. The
input mode always remaining its original functions.
Once the BZ/BZ option is selected, the buzzer output
signals are controlled by PB0 data register only. The I/O
functions of PB0/PB1 are shown below.
PB0 I/O
I
I
I
I
PB1 I/O
I
O O O
PB0/PB1 Mode
x
C
B
PB0 Data
x
x
0
PB1 Data
RES signal to perform chip reset.
The relationship between VDD and VLVR is shown below.
V D D
5 .5 V
O O O O O O
I
I
B
C
B B C
B
B
1
D
0 1 D0 0
1
x
D
x
x
x
x x D1 x
x
I
I
I
D
0 B D0 0
B
PB1 Pad Status I
D
0
B
I
I
B
O P R
5 .5 V
I D1 0
V
L V R
3 .0 V
2 .2 V
0 .9 V
Note:
I: input; O: output; D, D0, D1: data;
B: buzzer option, BZ or BZ; x: don't care
C: CMOS output
V
V
I O O O
PB0 Pad Status I
Note:
· The LVR uses the ²OR² function with the external
VOPR is the voltage range for proper chip operation at 4MHz system clock.
D D
5 .5 V
V
L V R
L V R
D e te c t V o lta g e
0 .9 V
0 V
R e s e t S ig n a l
N o r m a l O p e r a tio n
R e s e t
R e s e t
*1
*2
Low Voltage Reset
Note:
*1: To make sure that the system oscillator has stabilized, the SST provides an extra delay of
1024 system clock pulses before entering the normal operation.
*2: Since low voltage has to be maintained in its original state and exceed 1ms, therefore 1ms
delay enters the reset mode.
Rev. 1.10
15
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
Options
The following table shows all kinds of options in the microcontroller. All of the options must be defined to ensure proper
system functioning.
Items
Options
1
WDT clock source: WDTOSC or fSYS/4
2
WDT function: enable or disable
3
LVR function: enable or disable
4
CLRWDT instruction(s): one or two clear WDT instruction(s)
5
System oscillator: RC or crystal
6
Pull-high resistors (PA~PC): none or pull-high
7
BZ function: enable or disable
8
PA0~PA7 wake-up: enable or disable
Rev. 1.10
16
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
Application Circuits
V
D D
0 .0 1 m F *
V D D
P A 0 ~ P A 7
R E S
P B 0 /B Z
P B 1 /B Z
P B 2
1 0 0 k W
0 .1 m F
1 0 k W
V
0 .1 m F *
V S S
P C 0 /IN T
P C 1 /T M R
D D
R
O S C
4 7 0 p F
O S C
C ir c u it
O S C 1
O S C 2
O S C 1
fS
Y S
/4
C 1
O S C 2
O S C 1
S e e R ig h t S id e
C 2
O S C 2
R 1
H T 4 8 R 0 5 A -1 /H T 4 8 C 0 5
H T 4 8 R 0 6 A -1 /H T 4 8 C 0 6
Note:
R C S y s te m O s c illa to r
2 4 k W < R O S C < 1 M W
O S C
C ry s ta l S y s te m
F o r th e v a lu e s ,
s e e ta b le b e lo w
O s c illa to r
C ir c u it
The resistance and capacitance for reset circuit should be designed to ensure that the VDD is stable and remains in a valid range of the operating voltage before bringing RES to high.
²*² Make the length of the wiring, which is connected to the RES pin as short as possible, to avoid noise
interference.
The following table shows the C1, C2 and R1 value according different crystal values. (For reference only)
Crystal or Resonator
C1, C2
R1
4MHz Crystal
0pF
10kW
4MHz Resonator
10pF
12kW
3.58MHz Crystal
0pF
10kW
3.58MHz Resonator
25pF
10kW
2MHz Crystal & Resonator
25pF
10kW
1MHz Crystal
35pF
27kW
480kHz Resonator
300pF
9.1kW
455kHz Resonator
300pF
10kW
429kHz Resonator
300pF
10kW
The function of the resistor R1 is to ensure that the oscillator will switch off should low voltage conditions occur. Such a low voltage, as mentioned here, is one which is less than the lowest value of the
MCU operating voltage. Note however that if the LVR is enabled then R1 can be removed.
Rev. 1.10
17
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
Instruction Set Summary
Description
Instruction
Cycle
Flag
Affected
Add data memory to ACC
Add ACC to data memory
Add immediate data to ACC
Add data memory to ACC with carry
Add ACC to data memory with carry
Subtract immediate data from ACC
Subtract data memory from ACC
Subtract data memory from ACC with result in data memory
Subtract data memory from ACC with carry
Subtract data memory from ACC with carry and result in data memory
Decimal adjust ACC for addition with result in data memory
1
1(1)
1
1
1(1)
1
1
1(1)
1
1(1)
1(1)
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
C
1
1
1
1(1)
1(1)
1(1)
1
1
1
1(1)
1
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Increment data memory with result in ACC
Increment data memory
Decrement data memory with result in ACC
Decrement data memory
1
1(1)
1
1(1)
Z
Z
Z
Z
Rotate data memory right with result in ACC
Rotate data memory right
Rotate data memory right through carry with result in ACC
Rotate data memory right through carry
Rotate data memory left with result in ACC
Rotate data memory left
Rotate data memory left through carry with result in ACC
Rotate data memory left through carry
1
1(1)
1
1(1)
1
1(1)
1
1(1)
None
None
C
C
None
None
C
C
Move data memory to ACC
Move ACC to data memory
Move immediate data to ACC
1
1(1)
1
None
None
None
Clear bit of data memory
Set bit of data memory
1(1)
1(1)
None
None
Mnemonic
Arithmetic
ADD A,[m]
ADDM A,[m]
ADD A,x
ADC A,[m]
ADCM A,[m]
SUB A,x
SUB A,[m]
SUBM A,[m]
SBC A,[m]
SBCM A,[m]
DAA [m]
Logic Operation
AND A,[m]
OR A,[m]
XOR A,[m]
ANDM A,[m]
ORM A,[m]
XORM A,[m]
AND A,x
OR A,x
XOR A,x
CPL [m]
CPLA [m]
AND data memory to ACC
OR data memory to ACC
Exclusive-OR data memory to ACC
AND ACC to data memory
OR ACC to data memory
Exclusive-OR ACC to data memory
AND immediate data to ACC
OR immediate data to ACC
Exclusive-OR immediate data to ACC
Complement data memory
Complement data memory with result in ACC
Increment & Decrement
INCA [m]
INC [m]
DECA [m]
DEC [m]
Rotate
RRA [m]
RR [m]
RRCA [m]
RRC [m]
RLA [m]
RL [m]
RLCA [m]
RLC [m]
Data Move
MOV A,[m]
MOV [m],A
MOV A,x
Bit Operation
CLR [m].i
SET [m].i
Rev. 1.10
18
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
Instruction
Cycle
Flag
Affected
Jump unconditionally
Skip if data memory is zero
Skip if data memory is zero with data movement to ACC
Skip if bit i of data memory is zero
Skip if bit i of data memory is not zero
Skip if increment data memory is zero
Skip if decrement data memory is zero
Skip if increment data memory is zero with result in ACC
Skip if decrement data memory is zero with result in ACC
Subroutine call
Return from subroutine
Return from subroutine and load immediate data to ACC
Return from interrupt
2
1(2)
1(2)
1(2)
1(2)
1(3)
1(3)
1(2)
1(2)
2
2
2
2
None
None
None
None
None
None
None
None
None
None
None
None
None
Read ROM code (current page) to data memory and TBLH
Read ROM code (last page) to data memory and TBLH
(This instruction is not valid for HT48R05A-1/HT48C05)
2(1)
2(1)
None
None
No operation
Clear data memory
Set data memory
Clear Watchdog Timer
Pre-clear Watchdog Timer
Pre-clear Watchdog Timer
Swap nibbles of data memory
Swap nibbles of data memory with result in ACC
Enter power down mode
1
1(1)
1(1)
1
1
1
1(1)
1
1
None
None
None
TO,PDF
TO(4),PDF(4)
TO(4),PDF(4)
None
None
TO,PDF
Mnemonic
Description
Branch
JMP addr
SZ [m]
SZA [m]
SZ [m].i
SNZ [m].i
SIZ [m]
SDZ [m]
SIZA [m]
SDZA [m]
CALL addr
RET
RET A,x
RETI
Table Read
TABRDC [m]
TABRDL [m]
Miscellaneous
NOP
CLR [m]
SET [m]
CLR WDT
CLR WDT1
CLR WDT2
SWAP [m]
SWAPA [m]
HALT
Note:
x: Immediate data
m: Data memory address
A: Accumulator
i: 0~7 number of bits
addr: Program memory address
Ö: Flag is affected
-: Flag is not affected
(1)
: If a loading to the PCL register occurs, the execution cycle of instructions will be delayed for one more cycle
(four system clocks).
(2)
: If a skipping to the next instruction occurs, the execution cycle of instructions will be delayed for one more
cycle (four system clocks). Otherwise the original instruction cycle is unchanged.
(3) (1)
:
(4)
Rev. 1.10
and (2)
: The flags may be affected by the execution status. If the Watchdog Timer is cleared by executing the
²CLR WDT1² or ²CLR WDT2² instruction, the TO and PDF are cleared.
Otherwise the TO and PDF flags remain unchanged.
19
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
Instruction Definition
ADC A,[m]
Add data memory and carry to the accumulator
Description
The contents of the specified data memory, accumulator and the carry flag are added simultaneously, leaving the result in the accumulator.
Operation
ACC ¬ ACC+[m]+C
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
ADCM A,[m]
Add the accumulator and carry to data memory
Description
The contents of the specified data memory, accumulator and the carry flag are added simultaneously, leaving the result in the specified data memory.
Operation
[m] ¬ ACC+[m]+C
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
ADD A,[m]
Add data memory to the accumulator
Description
The contents of the specified data memory and the accumulator are added. The result is
stored in the accumulator.
Operation
ACC ¬ ACC+[m]
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
ADD A,x
Add immediate data to the accumulator
Description
The contents of the accumulator and the specified data are added, leaving the result in the
accumulator.
Operation
ACC ¬ ACC+x
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
ADDM A,[m]
Add the accumulator to the data memory
Description
The contents of the specified data memory and the accumulator are added. The result is
stored in the data memory.
Operation
[m] ¬ ACC+[m]
Affected flag(s)
Rev. 1.10
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
20
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
AND A,[m]
Logical AND accumulator with data memory
Description
Data in the accumulator and the specified data memory perform a bitwise logical_AND operation. The result is stored in the accumulator.
Operation
ACC ¬ ACC ²AND² [m]
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
AND A,x
Logical AND immediate data to the accumulator
Description
Data in the accumulator and the specified data perform a bitwise logical_AND operation.
The result is stored in the accumulator.
Operation
ACC ¬ ACC ²AND² x
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
ANDM A,[m]
Logical AND data memory with the accumulator
Description
Data in the specified data memory and the accumulator perform a bitwise logical_AND operation. The result is stored in the data memory.
Operation
[m] ¬ ACC ²AND² [m]
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
CALL addr
Subroutine call
Description
The instruction unconditionally calls a subroutine located at the indicated address. The
program counter increments once to obtain the address of the next instruction, and pushes
this onto the stack. The indicated address is then loaded. Program execution continues
with the instruction at this address.
Operation
Stack ¬ PC+1
PC ¬ addr
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
CLR [m]
Clear data memory
Description
The contents of the specified data memory are cleared to 0.
Operation
[m] ¬ 00H
Affected flag(s)
Rev. 1.10
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
21
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
CLR [m].i
Clear bit of data memory
Description
The bit i of the specified data memory is cleared to 0.
Operation
[m].i ¬ 0
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
CLR WDT
Clear Watchdog Timer
Description
The WDT is cleared (clears the WDT). The power down bit (PDF) and time-out bit (TO) are
cleared.
Operation
WDT ¬ 00H
PDF and TO ¬ 0
Affected flag(s)
TO
PDF
OV
Z
AC
C
0
0
¾
¾
¾
¾
CLR WDT1
Preclear Watchdog Timer
Description
Together with CLR WDT2, clears the WDT. PDF and TO are also cleared. Only execution
of this instruction without the other preclear instruction just sets the indicated flag which implies this instruction has been executed and the TO and PDF flags remain unchanged.
Operation
WDT ¬ 00H*
PDF and TO ¬ 0*
Affected flag(s)
TO
PDF
OV
Z
AC
C
0*
0*
¾
¾
¾
¾
CLR WDT2
Preclear Watchdog Timer
Description
Together with CLR WDT1, clears the WDT. PDF and TO are also cleared. Only execution
of this instruction without the other preclear instruction, sets the indicated flag which implies this instruction has been executed and the TO and PDF flags remain unchanged.
Operation
WDT ¬ 00H*
PDF and TO ¬ 0*
Affected flag(s)
TO
PDF
OV
Z
AC
C
0*
0*
¾
¾
¾
¾
CPL [m]
Complement data memory
Description
Each bit of the specified data memory is logically complemented (1¢s complement). Bits
which previously contained a 1 are changed to 0 and vice-versa.
Operation
[m] ¬ [m]
Affected flag(s)
Rev. 1.10
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
22
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
CPLA [m]
Complement data memory and place result in the accumulator
Description
Each bit of the specified data memory is logically complemented (1¢s complement). Bits
which previously contained a 1 are changed to 0 and vice-versa. The complemented result
is stored in the accumulator and the contents of the data memory remain unchanged.
Operation
ACC ¬ [m]
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
DAA [m]
Decimal-Adjust accumulator for addition
Description
The accumulator value is adjusted to the BCD (Binary Coded Decimal) code. The accumulator is divided into two nibbles. Each nibble is adjusted to the BCD code and an internal
carry (AC1) will be done if the low nibble of the accumulator is greater than 9. The BCD adjustment is done by adding 6 to the original value if the original value is greater than 9 or a
carry (AC or C) is set; otherwise the original value remains unchanged. The result is stored
in the data memory and only the carry flag (C) may be affected.
Operation
If ACC.3~ACC.0 >9 or AC=1
then [m].3~[m].0 ¬ (ACC.3~ACC.0)+6, AC1=AC
else [m].3~[m].0 ¬ (ACC.3~ACC.0), AC1=0
and
If ACC.7~ACC.4+AC1 >9 or C=1
then [m].7~[m].4 ¬ ACC.7~ACC.4+6+AC1,C=1
else [m].7~[m].4 ¬ ACC.7~ACC.4+AC1,C=C
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
DEC [m]
Decrement data memory
Description
Data in the specified data memory is decremented by 1.
Operation
[m] ¬ [m]-1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
DECA [m]
Decrement data memory and place result in the accumulator
Description
Data in the specified data memory is decremented by 1, leaving the result in the accumulator. The contents of the data memory remain unchanged.
Operation
ACC ¬ [m]-1
Affected flag(s)
Rev. 1.10
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
23
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
HALT
Enter power down mode
Description
This instruction stops program execution and turns off the system clock. The contents of
the RAM and registers are retained. The WDT and prescaler are cleared. The power down
bit (PDF) is set and the WDT time-out bit (TO) is cleared.
Operation
PC ¬ PC+1
PDF ¬ 1
TO ¬ 0
Affected flag(s)
TO
PDF
OV
Z
AC
C
0
1
¾
¾
¾
¾
INC [m]
Increment data memory
Description
Data in the specified data memory is incremented by 1
Operation
[m] ¬ [m]+1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
INCA [m]
Increment data memory and place result in the accumulator
Description
Data in the specified data memory is incremented by 1, leaving the result in the accumulator. The contents of the data memory remain unchanged.
Operation
ACC ¬ [m]+1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
JMP addr
Directly jump
Description
The program counter are replaced with the directly-specified address unconditionally, and
control is passed to this destination.
Operation
PC ¬addr
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
MOV A,[m]
Move data memory to the accumulator
Description
The contents of the specified data memory are copied to the accumulator.
Operation
ACC ¬ [m]
Affected flag(s)
Rev. 1.10
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
24
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
MOV A,x
Move immediate data to the accumulator
Description
The 8-bit data specified by the code is loaded into the accumulator.
Operation
ACC ¬ x
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
MOV [m],A
Move the accumulator to data memory
Description
The contents of the accumulator are copied to the specified data memory (one of the data
memories).
Operation
[m] ¬ACC
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
NOP
No operation
Description
No operation is performed. Execution continues with the next instruction.
Operation
PC ¬ PC+1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
OR A,[m]
Logical OR accumulator with data memory
Description
Data in the accumulator and the specified data memory (one of the data memories) perform a bitwise logical_OR operation. The result is stored in the accumulator.
Operation
ACC ¬ ACC ²OR² [m]
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
OR A,x
Logical OR immediate data to the accumulator
Description
Data in the accumulator and the specified data perform a bitwise logical_OR operation.
The result is stored in the accumulator.
Operation
ACC ¬ ACC ²OR² x
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
ORM A,[m]
Logical OR data memory with the accumulator
Description
Data in the data memory (one of the data memories) and the accumulator perform a
bitwise logical_OR operation. The result is stored in the data memory.
Operation
[m] ¬ACC ²OR² [m]
Affected flag(s)
Rev. 1.10
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
25
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
RET
Return from subroutine
Description
The program counter is restored from the stack. This is a 2-cycle instruction.
Operation
PC ¬ Stack
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
RET A,x
Return and place immediate data in the accumulator
Description
The program counter is restored from the stack and the accumulator loaded with the specified 8-bit immediate data.
Operation
PC ¬ Stack
ACC ¬ x
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
RETI
Return from interrupt
Description
The program counter is restored from the stack, and interrupts are enabled by setting the
EMI bit. EMI is the enable master (global) interrupt bit.
Operation
PC ¬ Stack
EMI ¬ 1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
RL [m]
Rotate data memory left
Description
The contents of the specified data memory are rotated 1 bit left with bit 7 rotated into bit 0.
Operation
[m].(i+1) ¬ [m].i; [m].i:bit i of the data memory (i=0~6)
[m].0 ¬ [m].7
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
RLA [m]
Rotate data memory left and place result in the accumulator
Description
Data in the specified data memory is rotated 1 bit left with bit 7 rotated into bit 0, leaving the
rotated result in the accumulator. The contents of the data memory remain unchanged.
Operation
ACC.(i+1) ¬ [m].i; [m].i:bit i of the data memory (i=0~6)
ACC.0 ¬ [m].7
Affected flag(s)
Rev. 1.10
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
26
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
RLC [m]
Rotate data memory left through carry
Description
The contents of the specified data memory and the carry flag are rotated 1 bit left. Bit 7 replaces the carry bit; the original carry flag is rotated into the bit 0 position.
Operation
[m].(i+1) ¬ [m].i; [m].i:bit i of the data memory (i=0~6)
[m].0 ¬ C
C ¬ [m].7
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
RLCA [m]
Rotate left through carry and place result in the accumulator
Description
Data in the specified data memory and the carry flag are rotated 1 bit left. Bit 7 replaces the
carry bit and the original carry flag is rotated into bit 0 position. The rotated result is stored
in the accumulator but the contents of the data memory remain unchanged.
Operation
ACC.(i+1) ¬ [m].i; [m].i:bit i of the data memory (i=0~6)
ACC.0 ¬ C
C ¬ [m].7
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
RR [m]
Rotate data memory right
Description
The contents of the specified data memory are rotated 1 bit right with bit 0 rotated to bit 7.
Operation
[m].i ¬ [m].(i+1); [m].i:bit i of the data memory (i=0~6)
[m].7 ¬ [m].0
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
RRA [m]
Rotate right and place result in the accumulator
Description
Data in the specified data memory is rotated 1 bit right with bit 0 rotated into bit 7, leaving
the rotated result in the accumulator. The contents of the data memory remain unchanged.
Operation
ACC.(i) ¬ [m].(i+1); [m].i:bit i of the data memory (i=0~6)
ACC.7 ¬ [m].0
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
RRC [m]
Rotate data memory right through carry
Description
The contents of the specified data memory and the carry flag are together rotated 1 bit
right. Bit 0 replaces the carry bit; the original carry flag is rotated into the bit 7 position.
Operation
[m].i ¬ [m].(i+1); [m].i:bit i of the data memory (i=0~6)
[m].7 ¬ C
C ¬ [m].0
Affected flag(s)
Rev. 1.10
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
27
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
RRCA [m]
Rotate right through carry and place result in the accumulator
Description
Data of the specified data memory and the carry flag are rotated 1 bit right. Bit 0 replaces
the carry bit and the original carry flag is rotated into the bit 7 position. The rotated result is
stored in the accumulator. The contents of the data memory remain unchanged.
Operation
ACC.i ¬ [m].(i+1); [m].i:bit i of the data memory (i=0~6)
ACC.7 ¬ C
C ¬ [m].0
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
SBC A,[m]
Subtract data memory and carry from the accumulator
Description
The contents of the specified data memory and the complement of the carry flag are subtracted from the accumulator, leaving the result in the accumulator.
Operation
ACC ¬ ACC+[m]+C
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
SBCM A,[m]
Subtract data memory and carry from the accumulator
Description
The contents of the specified data memory and the complement of the carry flag are subtracted from the accumulator, leaving the result in the data memory.
Operation
[m] ¬ ACC+[m]+C
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
SDZ [m]
Skip if decrement data memory is 0
Description
The contents of the specified data memory are decremented by 1. If the result is 0, the next
instruction is skipped. If the result is 0, the following instruction, fetched during the current
instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle).
Operation
Skip if ([m]-1)=0, [m] ¬ ([m]-1)
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SDZA [m]
Decrement data memory and place result in ACC, skip if 0
Description
The contents of the specified data memory are decremented by 1. If the result is 0, the next
instruction is skipped. The result is stored in the accumulator but the data memory remains
unchanged. If the result is 0, the following instruction, fetched during the current instruction
execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle).
Operation
Skip if ([m]-1)=0, ACC ¬ ([m]-1)
Affected flag(s)
Rev. 1.10
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
28
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
SET [m]
Set data memory
Description
Each bit of the specified data memory is set to 1.
Operation
[m] ¬ FFH
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SET [m]. i
Set bit of data memory
Description
Bit i of the specified data memory is set to 1.
Operation
[m].i ¬ 1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SIZ [m]
Skip if increment data memory is 0
Description
The contents of the specified data memory are incremented by 1. If the result is 0, the following instruction, fetched during the current instruction execution, is discarded and a
dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with
the next instruction (1 cycle).
Operation
Skip if ([m]+1)=0, [m] ¬ ([m]+1)
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SIZA [m]
Increment data memory and place result in ACC, skip if 0
Description
The contents of the specified data memory are incremented by 1. If the result is 0, the next
instruction is skipped and the result is stored in the accumulator. The data memory remains unchanged. If the result is 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper
instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle).
Operation
Skip if ([m]+1)=0, ACC ¬ ([m]+1)
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SNZ [m].i
Skip if bit i of the data memory is not 0
Description
If bit i of the specified data memory is not 0, the next instruction is skipped. If bit i of the data
memory is not 0, the following instruction, fetched during the current instruction execution,
is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle).
Operation
Skip if [m].i¹0
Affected flag(s)
Rev. 1.10
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
29
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
SUB A,[m]
Subtract data memory from the accumulator
Description
The specified data memory is subtracted from the contents of the accumulator, leaving the
result in the accumulator.
Operation
ACC ¬ ACC+[m]+1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
SUBM A,[m]
Subtract data memory from the accumulator
Description
The specified data memory is subtracted from the contents of the accumulator, leaving the
result in the data memory.
Operation
[m] ¬ ACC+[m]+1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
SUB A,x
Subtract immediate data from the accumulator
Description
The immediate data specified by the code is subtracted from the contents of the accumulator, leaving the result in the accumulator.
Operation
ACC ¬ ACC+x+1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
SWAP [m]
Swap nibbles within the data memory
Description
The low-order and high-order nibbles of the specified data memory (1 of the data memories) are interchanged.
Operation
[m].3~[m].0 « [m].7~[m].4
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SWAPA [m]
Swap data memory and place result in the accumulator
Description
The low-order and high-order nibbles of the specified data memory are interchanged, writing the result to the accumulator. The contents of the data memory remain unchanged.
Operation
ACC.3~ACC.0 ¬ [m].7~[m].4
ACC.7~ACC.4 ¬ [m].3~[m].0
Affected flag(s)
Rev. 1.10
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
30
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
SZ [m]
Skip if data memory is 0
Description
If the contents of the specified data memory are 0, the following instruction, fetched during
the current instruction execution, is discarded and a dummy cycle is replaced to get the
proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle).
Operation
Skip if [m]=0
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SZA [m]
Move data memory to ACC, skip if 0
Description
The contents of the specified data memory are copied to the accumulator. If the contents is
0, the following instruction, fetched during the current instruction execution, is discarded
and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed
with the next instruction (1 cycle).
Operation
Skip if [m]=0
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SZ [m].i
Skip if bit i of the data memory is 0
Description
If bit i of the specified data memory is 0, the following instruction, fetched during the current
instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle).
Operation
Skip if [m].i=0
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
TABRDC [m]
Move the ROM code (current page) to TBLH and data memory
Description
The low byte of ROM code (current page) addressed by the table pointer (TBLP) is moved
to the specified data memory and the high byte transferred to TBLH directly.
Operation
[m] ¬ ROM code (low byte)
TBLH ¬ ROM code (high byte)
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
TABRDL [m]
Move the ROM code (last page) to TBLH and data memory
Description
The low byte of ROM code (last page) addressed by the table pointer (TBLP) is moved to
the data memory and the high byte transferred to TBLH directly.
Note that this instruction is not valid for HT48R05A-1/HT48C05
Operation
[m] ¬ ROM code (low byte)
TBLH ¬ ROM code (high byte)
Affected flag(s)
Rev. 1.10
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
31
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
XOR A,[m]
Logical XOR accumulator with data memory
Description
Data in the accumulator and the indicated data memory perform a bitwise logical Exclusive_OR operation and the result is stored in the accumulator.
Operation
ACC ¬ ACC ²XOR² [m]
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
XORM A,[m]
Logical XOR data memory with the accumulator
Description
Data in the indicated data memory and the accumulator perform a bitwise logical Exclusive_OR operation. The result is stored in the data memory. The 0 flag is affected.
Operation
[m] ¬ ACC ²XOR² [m]
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
XOR A,x
Logical XOR immediate data to the accumulator
Description
Data in the accumulator and the specified data perform a bitwise logical Exclusive_OR operation. The result is stored in the accumulator. The 0 flag is affected.
Operation
ACC ¬ ACC ²XOR² x
Affected flag(s)
Rev. 1.10
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
32
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
Package Information
16-pin SSOP (150mil) Outline Dimensions
9
1 6
A
B
1
8
C
C '
G
H
D
E
Symbol
Rev. 1.10
a
F
Dimensions in mil
Min.
Nom.
Max.
A
228
¾
244
B
150
¾
157
C
8
¾
12
C¢
189
¾
197
D
54
¾
60
E
¾
25
¾
F
4
¾
10
G
22
¾
28
H
7
¾
10
a
0°
¾
8°
33
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
18-pin DIP (300mil) Outline Dimensions
A
B
1 8
1 0
1
9
H
C
D
E
a
G
I
F
Symbol
A
Rev. 1.10
Dimensions in mil
Min.
Nom.
Max.
895
¾
915
B
240
¾
260
C
125
¾
135
D
125
¾
145
E
16
¾
20
F
50
¾
70
G
¾
100
¾
H
295
¾
315
I
335
¾
375
a
0°
¾
15°
34
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
18-pin SOP (300mil) Outline Dimensions
1 0
1 8
B
A
9
1
C
C '
G
H
D
E
Symbol
Rev. 1.10
a
F
Dimensions in mil
Min.
Nom.
Max.
A
394
¾
419
B
290
¾
300
C
14
¾
20
C¢
447
¾
460
D
92
¾
104
E
¾
50
¾
F
4
¾
¾
G
32
¾
38
H
4
¾
12
a
0°
¾
10°
35
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
Product Tape and Reel Specifications
Reel Dimensions
D
T 2
A
C
B
T 1
SSOP 16S
Symbol
Description
Dimensions in mm
A
Reel Outer Diameter
330±1.0
B
Reel Inner Diameter
62±1.5
C
Spindle Hole Diameter
13.0+0.5
-0.2
D
Key Slit Width
2.0±0.5
T1
Space Between Flange
12.8+0.3
-0.2
T2
Reel Thickness
18.2±0.2
SOP 18W
Symbol
Description
Dimensions in mm
A
Reel Outer Diameter
330±1.0
B
Reel Inner Diameter
62±1.5
C
Spindle Hole Diameter
13.0+0.5
-0.2
D
Key Slit Width
2.0±0.5
T1
Space Between Flange
24.8+0.3
-0.2
T2
Reel Thickness
30.2±0.2
Rev. 1.10
36
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
Carrier Tape Dimensions
P 0
D
P 1
t
E
F
W
C
D 1
B 0
P
K 0
A 0
SSOP 16S
Symbol
Description
Dimensions in mm
12.0+0.3
-0.1
W
Carrier Tape Width
P
Cavity Pitch
8.0±0.1
E
Perforation Position
1.75±0.1
F
Cavity to Perforation (Width Direction)
5.5±0.1
D
Perforation Diameter
1.55±0.1
D1
Cavity Hole Diameter
1.5+0.25
P0
Perforation Pitch
4.0±0.1
P1
Cavity to Perforation (Length Direction)
2.0±0.1
A0
Cavity Length
6.4±0.1
B0
Cavity Width
5.2±0.1
K0
Cavity Depth
2.1±0.1
t
Carrier Tape Thickness
C
Cover Tape Width
0.30±0.05
9.3
SOP 18W
Symbol
Description
Dimensions in mm
W
Carrier Tape Width
24.0+0.3
-0.1
P
Cavity Pitch
16.0±0.1
E
Perforation Position
1.75±0.1
F
Cavity to Perforation (Width Direction)
11.5±0.1
D
Perforation Diameter
1.5±0.1
D1
Cavity Hole Diameter
1.5+0.25
P0
Perforation Pitch
4.0±0.1
P1
Cavity to Perforation (Length Direction)
2.0±0.1
A0
Cavity Length
10.9±0.1
B0
Cavity Width
12.0±0.1
K0
Cavity Depth
2.8±0.1
t
Carrier Tape Thickness
0.3±0.05
C
Cover Tape Width
Rev. 1.10
21.3
37
June 9, 2004
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
Holtek Semiconductor Inc. (Headquarters)
No.3, Creation Rd. II, Science Park, Hsinchu, Taiwan
Tel: 886-3-563-1999
Fax: 886-3-563-1189
http://www.holtek.com.tw
Holtek Semiconductor Inc. (Taipei Sales Office)
4F-2, No. 3-2, YuanQu St., Nankang Software Park, Taipei 115, Taiwan
Tel: 886-2-2655-7070
Fax: 886-2-2655-7373
Fax: 886-2-2655-7383 (International sales hotline)
Holtek Semiconductor Inc. (Shanghai Sales Office)
7th Floor, Building 2, No.889, Yi Shan Rd., Shanghai, China 200233
Tel: 021-6485-5560
Fax: 021-6485-0313
http://www.holtek.com.cn
Holtek Semiconductor Inc. (Shenzhen Sales Office)
43F, SEG Plaza, Shen Nan Zhong Road, Shenzhen, China 518031
Tel:0755-83465589
Fax:0755-83465590
ISDN : 0755-8346559
Holtek Semiconductor Inc. (Beijing Sales Office)
Suite 1721, Jinyu Tower, A129 West Xuan Wu Men Street, Xicheng District, Beijing, China 100031
Tel:010-66410030, 66417751, 66417752
Fax:010-66410125
Holmate Semiconductor, Inc. (North America Sales Office)
46712 Fremont Blvd., Fremont, CA 94538
Tel: 510-252-9880
Fax: 510-252-9885
http://www.holmate.com
Copyright Ó 2004 by HOLTEK SEMICONDUCTOR INC.
The information appearing in this Data Sheet is believed to be accurate at the time of publication. However, Holtek assumes no responsibility arising from the use of the specifications described. The applications mentioned herein are used
solely for the purpose of illustration and Holtek makes no warranty or representation that such applications will be suitable
without further modification, nor recommends the use of its products for application that may present a risk to human life
due to malfunction or otherwise. Holtek¢s products are not authorized for use as critical components in life support devices
or systems. Holtek reserves the right to alter its products without prior notification. For the most up-to-date information,
please visit our web site at http://www.holtek.com.tw.
Rev. 1.10
38
June 9, 2004