HY62UF16101C Series 64Kx16bit full CMOS SRAM Document Title 64K x16 bit 3.0V Super Low Power Full CMOS Slow SRAM Revision History Revision No History Draft Date Remark 03 Divide output load into two factors - tCLZ,tOLZ,tBLZ,tCHZ,tOHZ,tBHZ,tWHZ,tOW - Others Add marking information Dec.10. 2000 Final 04 Add 100ns speed Dec.27. 2000 Final This document is a general product description and is subject to change without notice. Hynix Semiconductor does not assume any responsibility for use of circuits described. No patent licenses are implied. Rev.04 /Dec. 00 Hynix Semiconductor HY62UF16101C Series DESCRIPTION FEATURES The HY62UF16101C is a high speed, super low power and 1M bit full CMOS SRAM organized as 65,536 words by 16bit. The HY62UF16101C uses high performance full CMOS process technology and designed for high speed low power circuit technology. It is particularly well suited for used in high density low power system application. This device has a data retention mode that guarantees data to remain valid at a minimum power supply voltage of 1.2V. • Fully static operation and Tri-state output • TTL compatible inputs and outputs • Battery backup(LL/SL-part) -. 1.2V(min) data retention • Standard pin configuration -. 48 - FBGA Product Voltage Speed No. (V) (ns) HY62UF16101C 2.7~3.3 55/70/85/100 HY62UF16101C-I 2.7~3.3 55/70/85/100 Note 1. Blank : Commercial, I : Industrial 2. Current value is max. Operation Current/Icc(mA) 3 3 PIN CONNECTION /LB Temperature (°C) 0~70 -40~85(I) BLOCK DIAGRAM NC /CS IO1 IO10 IO11 A5 A6 IO2 IO3 Vss IO12 NC A7 IO4 Vcc Vcc IO13 NC NC IO5 Vss IO15 IO14 A14 A15 IO6 IO7 IO16 NC A12 A13 /WE IO8 NC A9 MEMORY ARRAY 128K x 16 A15 A10 A11 NC /CS /OE /LB /UB /WE I/O16 CONTROL LOGIC 48-FBGA(Top View) I/O1 DATA I/O BUFFER A4 ROW DECODER WRITE DRIVER IO9 /UB A3 A0 SENSE AMP A2 COLUMNDECODER A1 ADD INPUT BUFFER /OE A0 A8 Standby Current(uA) LL SL 5 1 5 1 PIN DESCRIPTION Pin Name /CS /WE /OE /LB /UB Rev.04 /Dec. 00 Pin Function Chip Select Write Enable Output Enable Low Byte Control(I/O1~I/O8) Upper Byte Control(I/O9~I/O16) Pin Name I/O1~I/O16 A0~A15 Vcc Vss NC Pin Function Data Inputs / Outputs Address Inputs Power(2.7V~3.3V) Ground No Connection 2 HY62UF16101C Series ORDERING INFORMATION Part No. HY62UF16101CLLF HY62UF16101CLLF-I HY62UF16101CSLF HY62UF16101CSLF-I Speed 55/70/85/100 55/70/85/100 55/70/85/100 55/70/85/100 Power LL-part LL-part SL-part SL-part Temp. I I Package FBGA FBGA FBGA FBGA Note 1 Blank : Commercial, I : Industrial ABSOLUTE MAXIMUM RATING (1) Symbol VIN, VOUT Vcc TA Parameter Input/Output Voltage Power Supply Operating Temperature TSTG PD TSOLDER Storage Temperature Power Dissipation Lead Soldering Temperature & Time Rating -0.2 to 3.6 -0.2 to 4.6 0 to 70 -40 to 85 -55 to 150 1.0 260 10 Unit V V °C °C °C W °C sec Remark HY62UF16101C HY62UF16101C-I Note 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is stress rating only and the functional operation of the device under these or any other conditions above those indicated in the operation of this specification is not implied. Exposure to the absolute maximum rating conditions for extended period may affect reliability. TRUTH TABLE /CS /WE /OE /LB /UB H X L L L X X H H H X X H H L X H L X L H L L H L X H X L H L L H L L L L X Mode Deselected Deselected Output Disabled Output Disabled Read Write I/O I/O1~I/O8 High-Z High-Z High-Z High-Z DOUT Hi-Z DOUT DIN Hi-Z DIN I/O9~I/O16 High-Z High-Z High-Z High-Z Hi-Z DOUT DOUT Hi-Z DIN DIN Power Stand by Stand by Active Active Active Active Note: 1. H=VIH, L=VIL, X=don't care(VIH or VIL) 2. /UB, /LB(Upper, Lower Byte enable) These active LOW inputs allow individual bytes to be written or read. When /LB is LOW, data is written or read to the lower byte, I/O 1 -I/O 8. When /UB is LOW, data is written or read to the Upper byte, I/O 9 -I/O 16. Rev.04 /Dec. 00 2 HY62UF16101C Series RECOMMENDED DC OPERATING CONDITION Symbol Vcc Vss VIH VIL Parameter Supply Voltage Ground Input High Voltage Input Low Voltage Min. 2.7 0 2.2 -0.3(1) Typ. 3.0 0 - Max. 3.3 0 Vcc+0.3 0.6 Unit V V V V Note : 1. VIL = -1.5V for pulse width less than 30ns 2. Undershoots are sampled and not 100% tested. DC ELECTRICAL CHARACTERISTICS Vcc = 2.7V~3.3V, TA = 0°C to 70°C / -40°C to 85°C (I) Sym Parameter Test Condition ILI Input Leakage Current Vss < VIN < Vcc ILO Output Leakage Current Vss < VOUT < Vcc, /CS = VIH or /OE = VIH or /WE = VIL, /UB = /LB = VIH Icc Operating Power Supply /CS = VIL, VIN = VIH or VIL, Current II/O = 0mA ICC1 Average Operating Current /CS < 0.2V, 1us Cycle Time,100% Duty, II/O = 0mA, VIN < 0.2V /CS = VIL, VIN = VIH or VIL Cycle Time = Min. 100% Duty II/O = 0mA ISB TTL Standby Current /CS = VIH or (TTL Input) /UB = /LB = VIH, VIN = VIH or VIL ISB1 Standby Current /CS > Vcc - 0.2V or SL (CMOS Input) /UB = /LB > Vcc - 0.2V, VIN > Vcc - 0.2V or LL VIN < Vss + 0.2V VOL Output Low Voltage IOL = 2.1mA VOH Output High Voltage IOH = -1.0mA Min. -1 -1 Typ. - Max. 1 1 Unit uA uA - - 3 mA - - 5 mA - - 45 mA - - 0.5 mA - - 1 uA 0.5 5 uA - 0.4 - V V 2.4 Note : 1.Typical values are at Vcc = 3.0V, TA = 25°C 2.Typical values are sampled and not 100% tested. CAPACITANCE (Temp = 25°C, f= 1.0MHz) Symbol Parameter CIN Input Capacitance(Add, /CS, /UB, /LB, /WE, /OE) COUT Output Capacitance(I/O) Condition VIN = 0V VI/O = 0V Max. 8 10 Unit pF pF Note : These parameters are sampled and not 100% tested Rev.04 /Dec. 00 3 HY62UF16101C Series AC CHARACTERISTICS Vcc = 2.7~3.3V, TA = 0°C to 70°C / -40°C to 85°C (I), unless otherwise specified -55 -70 # Symbol Parameter Min Max Min Max 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 READ CYCLE tRC Read Cycle Time tAA Address Access Time tACS Chip Select Access Time tOE Output Enable to Output Valid tBA /LB, /UB Access Time tCLZ Chip Select to Output in Low Z tOLZ Output Enable to Output in Low Z tBLZ /LB, /UB Enable to Output in Low Z tCHZ Chip Deselection to Output in High Z tOHZ Out Disable to Output in High Z tBHZ /LB, /UB Disable to Output in High Z tOH Output Hold from Address Change WRITE CYCLE tWC Write Cycle Time tCW Chip Selection to End of Write tAW Address Valid to End of Write tBW /LB, /UB Valid to End of Write tAS Address Set-up Time tWP Write Pulse Width tWR Write Recovery Time tWHZ Write to Output in High Z tDW Data to Write Time Overlap tDH Data Hold from Write Time tOW Output Active from End of Write -85 -10 Min Max Min Max Unit 55 10 5 5 0 0 0 10 55 55 35 55 30 30 30 - 70 10 5 5 0 0 0 10 70 70 40 70 30 30 30 - 85 10 5 5 0 0 0 10 85 85 45 85 30 30 30 - 100 20 5 10 0 0 0 15 100 100 50 100 30 30 30 - ns ns ns ns ns ns ns ns ns ns ns ns 55 50 50 50 0 45 0 0 25 0 5 20 - 70 60 60 60 0 50 0 0 30 0 5 25 - 85 70 70 70 0 55 0 0 35 0 5 30 - 100 80 80 80 0 75 0 0 45 0 10 35 - ns ns ns ns ns ns ns ns ns ns ns AC TEST CONDITIONS TA = 0°C to 70°C / -40°C to 85°C (I), unless otherwise specified Parameter Input Pulse Level Input Rise and Fall Time Input and Output Timing Reference Level Output Load tCLZ,tOLZ,tBLZ,tCHZ,tOHZ,tBHZ,tWHZ,tOW Others Value 0.4V to 2.2V 5ns 1.5V CL = 5pF + 1TTL Load CL = 30pF + 1TTL Load AC TEST LOADS VTM=2.8V 1029 Ohm DOUT CL(1) 1728 Ohm Note 1. Including jig and scope capacitance Rev.04 /Dec. 00 4 HY62UF16101C Series TIMING DIAGRAM READ CYCLE 1(Note 1,4) tRC ADDR tAA tOH tACS /CS tCHZ(3) tBA /UB ,/ LB Data Out tBHZ(3) tOE /OE High-Z tOLZ(3) tBLZ(3) tCLZ(3) tOHZ(3) Data Valid READ CYCLE 2(Note 1,2,4) tRC ADDR tAA tOH tOH Data Out Previous Data Data Valid READ CYCLE 3(Note 1,2,4) /CS /UB, /LB tACS tCLZ(3) Data Out tCHZ(3) Data Valid Notes: A read occurs during the overlap of a low /OE, a high /WE, a low /CS1 and low /UB and/or /LB. 2. /OE = VIL 3. Transition is measured + 200mV from steady state voltage. This parameter is sampled and not 100% tested. 4. /CS in high for the standby, low for active /UB and /LB in high for the standby, low for active Rev.04 /Dec. 00 5 HY62UF16101C Series WRITE CYCLE 1(1,4,8) (/WE Controlled) tWC ADDR tWR(2) tCW /CS tAW tBW /UB,/LB tWP /WE tAS Data In tDW High-Z tDH Data Valid tWHZ(3,7) tOW (5) (6) Data Out WRITE CYCLE 2 (Note 1,4,8) (/CS Controlled) tWC ADDR tCW tAS tWR(2) /CS tAW tBW /UB,/LB tWP /WE tDW Data In Data Out High-Z tDH Data Valid High-Z Notes: 1. A write occurs during the overlap of a low /WE, a low /CS1 and low /UB and/or /LB. 2. tWR is measured from the earlier of /CS, /LB, /UB, or /WE going high to the end of write cycle. 3. During this period, I/O pins are in the output state so that the input signals of opposite phase to the output must not be applied. 4. If the /CS, /LB and /UB low transition occur simultaneously with the /WE low transition or after the /WE transition, outputs remain in a high impedance state. 5. Q(data out) is the same phase with the write data of this write cycle. 6. Q(data out) is the read data of the next address. 7. Transition is measured + 200mV from steady state. This parameter is sampled and not 100% tested. 8. /CS in high for the standby, low for active /UB and /LB in high for the standby, low for active Rev.04 /Dec. 00 6 HY62UF16101C Series DATA RETENTION ELECTRIC CHARACTERISTIC TA=0°C to 70°C / -40°C to 85°C (I) Symbol Parameter VDR Vcc for Data Retention ICCDR tCDR tR Data Retention Current Chip Deselect to Data Retention Time Operating Recovery Time Test Condition /CS > Vcc - 0.2V or /UB = /LB > Vcc-0.2V, VIN > Vcc - 0.2V or VIN < Vss + 0.2V Vcc=1.5V, /CS > Vcc - 0.2V, LL /UB = /LB > Vcc-0.2V, VIN > Vcc - 0.2V or SL VIN < Vss + 0.2V See Data Retention Timing Diagram Min 1.2 Typ - Max 3.3 Unit V - 0.5 2 uA - - 1 uA 0 - - ns tRC(2) - - ns Notes: 1. Typical values are under the condition of TA = 25°C. 2. tRC is read cycle time. DATA RETENTION TIMING DIAGRAM DATA RETENTION MODE VCC 2.7V tCDR tR VDR CS or /UB &/LB CS > VCC-0.2V or /UB = /LB > Vcc – 0.2V VSS Rev.04 /Dec. 00 7 HY62UF16101C Series PACKAGE INFORMATION 48ball Fine-Pitch Ball Grid Array Package(F) BOTTOM VIEW TOP VIEW B A A1 CORNER INDEX AREA 6 5 4 3 2 B1/2 1 A A B C D C C1 E F G C1/2 C1/2 H B1/2 B1 SIDE VIEW 5 E1 E2 C E SEATING PLANE A 4 r 3 D(DIAMETER) Note Symbol A B B1 C C1 D E E1 E2 r Rev.04 /Dec. 00 Min. 6.1 6.2 0.3 0.9 0.7 0.2 - Typ. 0.75 3.75 6.2 5.25 6.3 0.35 1.0 0.75 0.25 - Max. 6.3 6.4 0.4 1.1 0.8 0.3 0.1 1. DIMENSIONING AND TOLERANCING PER ASME Y14. SM-1994. 2. ALL DIMENSIONS ARE MILLIMETERS. 3. DIMENSION “D” IS MEASURED AT THE MAXIMUM SOLDER BALL DIAMETER IN A PLANE PARALLEL TO DATUM C. 4. PRIMARY DATUM C(SEATING PLANE) IS DEFINED BY THE CROWN OF THE SOLDER BALLS. 5. THIS IS A CONTROLLING DIMENSION. 8 HY62UF16101C Series MARKING INSTRUCTION Package FBGA Marking Example H Y U s s t x x x F x 6 1 1 C c y y w w p K O R x Index • HYUF611Cc c • ss : Part Name : Power Consumption -L -S : Low Low Power : Super Low Power : Speed - 55 - 70 - 85 - 10 : 55ns : 70ns : 85ns : 100ns • t : Temperature -C -I • yy : Year (ex : 00 = year 2000, 01= year 2001) • ww : Work Week ( ex : 12 = work week 12 ) • p : Process Code • xxxxx : Lot No. • KOR : Origin Country Note - Capital Letter - Small Letter : Fixed Item : Non-fixed Item Rev.04 /Dec. 00 : Industrial ( -0 ~ 70 °C ) : Industrial ( -40 ~ 85 °C ) 9