SN74LVC543A OCTAL REGISTERED TRANSCEIVER WITH 3-STATE OUTPUTS SCAS299F – JANUARY 1993 – REVISED JUNE 1998 D D D D D D D EPIC (Enhanced-Performance Implanted CMOS) Submicron Process Typical VOLP (Output Ground Bounce) < 0.8 V at VCC = 3.3 V, TA = 25°C Typical VOHV (Output VOH Undershoot) > 2 V at VCC = 3.3 V, TA = 25°C Power Off Disables Outputs, Permitting Live Insertion Supports Mixed-Mode Signal Operation on All Ports (5-V Input/Output Voltage With 3.3-V VCC) Latch-Up Performance Exceeds 250 mA Per JESD 17 Package Options Include Plastic Small-Outline (DW), Shrink Small-Outline (DB), and Thin Shrink Small-Outline (PW) Packages DB, DW, OR PW PACKAGE (TOP VIEW) LEBA OEBA A1 A2 A3 A4 A5 A6 A7 A8 CEAB GND 1 24 2 23 3 22 4 21 5 20 6 19 7 18 8 17 9 16 10 15 11 14 12 13 VCC CEBA B1 B2 B3 B4 B5 B6 B7 B8 LEAB OEAB description This octal registered transceiver is designed for 1.65-V to 3.6-V VCC operation. The SN74LVC543A contains two sets of D-type latches for temporary storage of data flowing in either direction. Separate latch-enable (LEAB or LEBA) and output-enable (OEAB or OEBA) inputs are provided for each register to permit independent control in either direction of data flow. The A-to-B enable (CEAB) input must be low to enter data from A or to output data from B. If CEAB is low and LEAB is low, the A-to-B latches are transparent; a subsequent low-to-high transition of LEAB places the A latches in the storage mode. With CEAB and OEAB both low, the 3-state B outputs are active and reflect the data present at the output of the A latches. Data flow for B to A is similar to that of A to B, but uses CEBA, LEBA, and OEBA. To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. Inputs can be driven from either 3.3-V or 5-V devices. This feature allows the use of these devices as translators in a mixed 3.3-V/5-V system environment. The SN74LVC543A is characterized for operation from –40°C to 85°C. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. EPIC is a trademark of Texas Instruments Incorporated. Copyright 1998, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN74LVC543A OCTAL REGISTERED TRANSCEIVER WITH 3-STATE OUTPUTS SCAS299F – JANUARY 1993 – REVISED JUNE 1998 FUNCTION TABLE† INPUTS OEAB A OUTPUT B CEAB LEAB H X X X Z X X H X Z L H L X L L L L B0‡ L L L L H H † A-to-B data flow is shown; B-to-A flow control is the same except that it uses CEBA, LEBA, and OEBA. ‡ Output level before the indicated steady-state input conditions were established logic symbol§ OEBA CEBA LEBA 2 1EN3 23 1 1C5 13 OEAB 11 CEAB 14 LEAB A1 A2 A3 A4 A5 A6 A7 A8 G1 2EN4 G2 2C6 3 4 3 1 5D 6D 1 4 21 5 20 6 19 7 18 8 17 9 16 10 15 § This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. 2 22 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 B1 B2 B3 B4 B5 B6 B7 B8 SN74LVC543A OCTAL REGISTERED TRANSCEIVER WITH 3-STATE OUTPUTS SCAS299F – JANUARY 1993 – REVISED JUNE 1998 logic diagram (positive logic) OEBA CEBA LEBA OEAB CEAB LEAB A1 2 23 1 13 11 14 C1 3 1D 22 B1 C1 1D To Seven Other Channels absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 6.5 V Input voltage range, VI: (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 6.5 V Voltage range applied to any output in the high-impedance or power-off state, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 6.5 V Voltage range applied to any output in the high or low state, VO (see Notes 1 and 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Continuous output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±100 mA Package thermal impedance, θJA (see Note 3): DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104°C/W DW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81°C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. The value of VCC is provided in the recommended operating conditions table. 3. The package thermal impedance is calculated in accordance with JESD 51. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 SN74LVC543A OCTAL REGISTERED TRANSCEIVER WITH 3-STATE OUTPUTS SCAS299F – JANUARY 1993 – REVISED JUNE 1998 recommended operating conditions (see Note 4) VCC Supply voltage VIH High-level input voltage Operating Data retention only VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 2.7 V to 3.6 V VCC = 1.65 V to 1.95 V VIL Low-level input voltage VI Input voltage VO Output voltage IOH Low level output current Low-level ∆t/∆v Input transition rise or fall rate MAX 3.6 1.5 0.65×VCC 1.7 UNIT V V 2 0.35×VCC 0.7 VCC = 2.3 V to 2.7 V VCC = 2.7 V to 3.6 V High level output current High-level IOL MIN 1.65 V 0.8 0 5.5 V High or low state 0 3 state 0 VCC 5.5 V VCC = 1.65 V VCC = 2.3 V –4 VCC = 2.7 V VCC = 3 V –12 –8 mA –24 VCC = 1.65 V VCC = 2.3 V 4 VCC = 2.7 V VCC = 3 V 12 8 mA 24 0 10 ns/V TA Operating free-air temperature –40 85 °C NOTE 4: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN74LVC543A OCTAL REGISTERED TRANSCEIVER WITH 3-STATE OUTPUTS SCAS299F – JANUARY 1993 – REVISED JUNE 1998 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS VCC 1.65 V to 3.6 V IOH = –100 µA IOH = –4 mA 1.65 V 2.3 V 1.7 2.7 V 2.2 3V 2.4 3V 2.2 12 mA IOH = –12 IOH = –24 mA IOL = 100 µA VOL II Ioff Control inputs IOZ‡ ICC ∆ICC Ci MAX UNIT V 1.65 V to 3.6 V 0.2 IOL = 4 mA IOL = 8 mA 1.65 V 0.45 2.3 V 0.7 IOL = 12 mA IOL = 24 mA 2.7 V 0.4 3V 0.55 VI = 0 to 5.5 V VI or VO = 5.5 V 3.6 V ±5 µA 0 ±10 µA VO = 0 to 5.5 V VI = VCC or GND 3.6 V ≤ VI ≤ 5.5 V§ 3.6 V ± 10 µA IO = 0 10 36V 3.6 One input at VCC – 0.6 V, Other inputs at VCC or GND Control inputs TYP† VCC–0.2 1.2 IOH = –8 mA VOH MIN 10 2.7 V to 3.6 V VI = VCC or GND Cio A or B ports VO = VCC or GND † All typical values are at VCC = 3.3 V, TA = 25°C. ‡ For I/O ports, the parameter IOZ includes the input leakage current. § This applies in the disabled state only. 500 V µA µA 3.3 V 4.5 pF 3.3 V 7.5 pF timing requirements over recommended operating free-air temperature range (unless otherwise noted) (see Figures 1 through 3) VCC = 1.8 V ± 0.15 V MIN tw tsu MAX VCC = 2.5 V ± 0.2 V MIN MAX VCC = 2.7 V MIN MAX VCC = 3.3 V ± 0.3 V MIN UNIT MAX Pulse duration ¶ ¶ 3.3 3.3 ns Setup time, data before LE↑ or CE↑ ¶ ¶ 1.6 1.6 ns ¶ ¶ 2.1 2.1 ns th Hold time, data after LE↑ or CE↑ ¶ This information was not available at the time of publication. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 SN74LVC543A OCTAL REGISTERED TRANSCEIVER WITH 3-STATE OUTPUTS SCAS299F – JANUARY 1993 – REVISED JUNE 1998 switching characteristics over recommended operating free-air temperature range (unless otherwise noted) (see Figures 1 through 3) PARAMETER tpd d ten tdi dis FROM (INPUT) A or B LE OE TO (OUTPUT) VCC = 1.8 V ± 0.15 V MIN MAX MIN MAX † † † † † † B or A A or B CE OE VCC = 2.5 V ± 0.2 V A or B CE VCC = 2.7 V MIN VCC = 3.3 V ± 0.3 V MAX MIN MAX † 8 1 7 † † 9.5 1.2 8.5 † † † 9.2 1.3 7.7 † † † † 9.3 1.3 8 † † † † 7.5 1 7 † † † † 7.5 1 7 UNIT ns ns ns † This information was not available at the time of publication. operating characteristics, TA = 25°C TEST CONDITIONS PARAMETER Cpd Power dissipation capacitance per transceiver Outputs enabled Outputs disabled f = 10 MHz VCC = 1.8 V ± 0.15 V VCC = 2.5 V ± 0.2 V VCC = 3.3 V ± 0.3 V TYP TYP TYP † † 49 † † 6 † This information was not available at the time of publication. 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 UNIT pF SN74LVC543A OCTAL REGISTERED TRANSCEIVER WITH 3-STATE OUTPUTS SCAS299F – JANUARY 1993 – REVISED JUNE 1998 PARAMETER MEASUREMENT INFORMATION VCC = 1.8 V ± 0.15 V 2 × VCC S1 1k Ω From Output Under Test Open GND CL = 30 pF (see Note A) 1k Ω TEST S1 tpd tPLZ/tPZL tPHZ/tPZH Open 2 × VCC Open LOAD CIRCUIT tw VCC Timing Input VCC/2 VCC/2 VCC/2 0V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VCC/2 VCC/2 0V tPLH Output Control (low-level enabling) tPLZ VCC VCC/2 VCC/2 VOL Output Waveform 2 S1 at Open (see Note B) VOL + 0.15 V VOL tPHZ tPZH VOH VCC/2 0V Output Waveform 1 S1 at 2 × VCC (see Note B) tPHL VCC/2 VCC VCC/2 tPZL VCC Input VOLTAGE WAVEFORMS PULSE DURATION th VCC Data Input VCC/2 0V 0V tsu Output VCC VCC/2 Input VCC/2 VOH VOH – 0.15 V 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2 ns, tf ≤ 2 ns. D. The outputs are measured one at a time with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. Figure 1. Load Circuit and Voltage Waveforms POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 SN74LVC543A OCTAL REGISTERED TRANSCEIVER WITH 3-STATE OUTPUTS SCAS299F – JANUARY 1993 – REVISED JUNE 1998 PARAMETER MEASUREMENT INFORMATION VCC = 2.5 V ± 0.2 V 2 × VCC S1 500 Ω From Output Under Test Open GND CL = 30 pF (see Note A) 500 Ω TEST S1 tpd tPLZ/tPZL tPHZ/tPZH Open 2 × VCC GND LOAD CIRCUIT tw VCC Timing Input VCC/2 VCC/2 VCC/2 0V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VCC/2 VCC/2 0V tPLH Output Control (low-level enabling) tPLZ VCC VCC/2 VCC/2 VOL Output Waveform 2 S1 at GND (see Note B) VOL + 0.15 V VOL tPHZ tPZH VOH VCC/2 0V Output Waveform 1 S1 at 2 × VCC (see Note B) tPHL VCC/2 VCC VCC/2 tPZL VCC Input VOLTAGE WAVEFORMS PULSE DURATION th VCC Data Input VCC/2 0V 0V tsu Output VCC VCC/2 Input VCC/2 VOH VOH – 0.15 V 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2 ns, tf ≤ 2 ns. D. The outputs are measured one at a time with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. Figure 2. Load Circuit and Voltage Waveforms 8 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN74LVC543A OCTAL REGISTERED TRANSCEIVER WITH 3-STATE OUTPUTS SCAS299F – JANUARY 1993 – REVISED JUNE 1998 PARAMETER MEASUREMENT INFORMATION VCC = 2.7 V AND 3.3 V ± 0.3 V 6V S1 500 Ω From Output Under Test Open GND CL = 50 pF (see Note A) 500 Ω TEST S1 tpd tPLZ/tPZL tPHZ/tPZH Open 6V GND tw LOAD CIRCUIT 2.7 V 2.7 V Timing Input 0V 0V VOLTAGE WAVEFORMS PULSE DURATION th 2.7 V Data Input 1.5 V 1.5 V 0V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES 1.5 V 1.5 V 0V tPLH tPHL VOH 1.5 V 2.7 V Output Control (low-level enabling) 1.5 V 1.5 V VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES tPLZ 3V Output Waveform 1 S1 at 6 V (see Note B) Output Waveform 2 S1 at GND (see Note B) 1.5 V 0V tPZL 2.7 V Output Input 1.5 V 1.5 V tsu Input 1.5 V 1.5 V tPZH VOL + 0.3 V VOL tPHZ 1.5 V VOH – 0.3 V VOH 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. D. The outputs are measured one at a time with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. Figure 3. Load Circuit and Voltage Waveforms POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 9 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 1998, Texas Instruments Incorporated