ECG006 The Communications Edge TM Product Information InGaP HBT Gain Block Product Features x DC – 5.5 GHz x +15.5 dBm P1dB at 1 GHz x +32 dBm OIP3 at 1 GHz x 15 dB Gain at 1 GHz x 4.0 dB Noise Figure at 2 GHz x Available in SOT-363, SOT-86, and lead-free / green SOT-89 Package Styles x Internally matched to 50 : Applications x Mobile Infrastructure x CATV / DBS x W-LAN / ISM x RFID x Defense / Homeland Security x Fixed Wireless Product Description GND The ECG006 is a general-purpose buffer amplifier that offers high dynamic range in a low-cost surface-mount package. At 1000 MHz, the ECG006 typically provides 15 dB of gain, +32 dBm Output IP3, and +15.5 dBm P1dB. The ECG006 consists of Darlington pair amplifiers using the high reliability InGaP/GaAs HBT process technology and only requires DC-blocking capacitors, a bias resistor, and an inductive RF choke for operation. The device is ideal for wireless applications and is available in low-cost, surface-mountable plastic SOT-86, SOT-363, and SOT-89 packages. The ECG006 is also available in a leadfree/green/RoHS-compliant SOT-89 package. All devices are 100% RF and DC tested. 4 1 2 3 RF IN GND RF OUT ECG006B / ECG006B-G GND 4 RF In 3 RF Out 1 2 GND ECG006C The broadband MMIC amplifier can be directly applied to various current and next generation wireless technologies such as GPRS, GSM, CDMA, and W-CDMA. In addition, the ECG006 will work for other various applications within the DC to 5.5 GHz frequency range such as CATV and fixed wireless. Specifications (1) Parameter Functional Diagram GND 1 6 RF OUT GND 2 5 GND RF IN 3 4 GND ECG006F Typical Performance (4) Units Min MHz MHz dB dBm dBm MHz dB dB dB dB dBm dBm dB V mA DC Operational Bandwidth Test Frequency Gain Output P1dB Output IP3 (2) Test Frequency Gain Large-signal Gain (3) Input Return Loss Output Return Loss Output P1dB Output IP3 (2) Noise Figure Device Voltage Device Current 11.5 3.5 Typ 1000 15 +15.4 +32 2000 14 13 18 14 15.0 32 4.0 3.9 45 Max Parameter Units 5500 Frequency S21 S11 S22 Output P1dB Output IP3 (2) Noise Figure MHz dB dB dB dBm dBm dB Operating Case Temperature Storage Temperature Device Current RF Input Power (continuous) Junction Temperature 1900 14.2 -17.4 -14.5 +15 +30 3.7 2140 14 -18 -15 +15 +30 3.7 System. 4.3 Ordering Information Part No. Absolute Maximum Rating Parameter 900 15 -14 -13 +15.4 +32 3.7 4. Test conditions: T = 25º C, Supply Voltage = +5 V, Device Voltage = +3.9V, Rbias = 24.3 , 50 1. Test conditions unless otherwise noted: 25º C, Supply Voltage = +5 V, Rbias = 24.3 , 50 System. 2. 3OIP measured with two tones at an output power of +2 dBm/tone separated by 1 MHz. The suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule. 3. Large-signal gain is tested with an input power level of +2 dBm. Typical 500 15.5 -20 -16 +15.8 +32 3.7 Rating -40 to +85 qC -55 to +150 qC 150 mA +12 dBm +250 qC Description ECG006B InGaP HBT Gain Block ECG006B-G InGaP HBT Gain Block ECG006C ECG006F ECG006B-PCB ECG006C-PCB ECG006F-PCB InGaP HBT Gain Block (SOT-86 Pkg) InGaP HBT Gain Block (SOT-363 Pkg) 700 – 2400 MHz Fully Assembled Eval. Board 700 – 2400 MHz Fully Assembled Eval. Board 700 – 2400 MHz Fully Assembled Eval. Board (leaded SOT-89 Pkg) (lead-free/green/RoHS-compliant SOT-89 Pkg) Operation of this device above any of these parameters may cause permanent damage. Specifications and information are subject to change without notice WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: [email protected] Web site: www.wj.com December 2004 Rev 1 ECG006 The Communications Edge TM Product Information InGaP HBT Gain Block Typical Device RF Performance Supply Bias = +5 V, Rbias = 24.3 :, Icc = 45 mA Frequency S21 S11 S22 Output P1dB Output IP3 Noise Figure MHz dB dB dB dBm dBm dB 100 15.3 -20 -29 +15.8 +31 3.8 500 15.2 -18 -16 +15.4 +31.5 3.7 900 15.1 -14 -13 +15.2 +32 3.6 1900 14.5 -17 -14 +15.0 +30 3.6 2140 14.3 -18 -14 +14.9 +30 3.6 2400 14.1 -20 -15 +14.6 +29.6 3.6 3500 13.9 -17 -15 +14 5800 10.2 -12.5 -9.5 1. Test conditions: T = 25º C, Supply Voltage = +5 V, Device Voltage = +3.9 V, Rbias = 24.3 , Icc = 45 mA typical, 50 System. 2. 3OIP measured with two tones at an output power of +2 dBm/tone separated by 1 MHz. The suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule. 3. Data is shown as device performance only. Actual implementation for the desired frequency band will be determined by external components shown in the application circuit. 0 16 -5 14 12 10 S22 -15 -20 +25C 1000 -40C +85C 1500 2000 Frequency (MHz) 2500 S11 -25 3000 0 4 30 3.5 25 5 6 +25°C 1000 -40°C 1500 2000 Frequency (MHz) +85°C 2500 3000 4.0 5.0 P1dB vs. Frequency 16 3 2 500 2.0 3.0 Vde (V) 18 2.5 20 15 500 2 3 4 Frequency (GHz) 90 80 70 60 50 +25°C 40 30 20 10 0 0.0 1.0 Noise Figure vs. Frequency 35 NF (dB) OIP3 (dBm) OIP3 vs. Frequency 1 P1dB (dBm) 8 500 -10 Vde vs. Icc Icc (mA) S11, S22 vs. Frequency 18 S11, S22 (dB) Gain Gain vs. Frequency 14 12 10 1000 1500 8 500 2000 Frequency (MHz) +25°C 1000 -40°C 1500 2000 Frequency (MHz) +85°C 2500 3000 Specifications and information are subject to change without notice WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: [email protected] Web site: www.wj.com December 2004 Rev 1 ECG006 The Communications Edge TM Product Information InGaP HBT Gain Block Recommended Application Circuit ECG006C-PCB Vcc Icc = 45 mA R4 Bias Resistor C4 Bypass Capacitor C3 0.018 µF L1 RF Choke RF IN RF OUT ECG006 C2 Blocking Capacitor C1 Blocking Capacitor ECG006F-PCB ECG006B-PCB Reference Designator L1 C1, C2, C4 50 820 nH .018 µF Recommended Component Values Frequency (MHz) 500 900 1900 2200 220 nH 68 nH 27 nH 22 nH 1000 pF 100 pF 68 pF 68 pF 2500 18 nH 56 pF Recommended Bias Resistor Values Supply R1 value Size Voltage 5V 24.4 ohms 0805 6V 46.7 ohms 0805 8V 91 ohms 1210 9V 113 ohms 1210 10 V 136 ohms 2010 12 V 180 ohms 2010 3500 15 nH 39 pF 1. The proper values for the components are dependent upon the intended frequency of operation. 2. The following values are contained on the evaluation board to achieve optimal broadband performance: Ref. Desig. L1 C1, C2 C3 C4 R4 Value / Type 39 nH wirewound inductor 56 pF chip capacitor 0.018 PF chip capacitor Do Not Place 24.3: 1% tolerance Size 0603 0603 0603 The proper value for R1 is dependent upon the supply voltage and allows for bias stability over temperature. WJ recommends a minimum supply bias of +5 V. A 1% tolerance resistor is recommended. 0805 Specifications and information are subject to change without notice WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: [email protected] Web site: www.wj.com December 2004 Rev 1 ECG006 The Communications Edge TM Product Information InGaP HBT Gain Block ECG006B (SOT-89 Package) Mechanical Information This package may contain lead-bearing materials. The plating material on the leads is SnPb. Outline Drawing Product Marking The component will be marked with an “E006” designator with an alphanumeric lot code on the top surface of the package. Tape and reel specifications for this part are located on the website in the “Application Notes” section. MSL / ESD Rating ESD Rating: Value: Test: Standard: Class 1A Passes between 250 and 500V Human Body Model (HBM) JEDEC Standard JESD22-A114 MSL Rating: Level 3 at +235 C convection reflow Standard: JEDEC Standard J-STD-020 Mounting Config. Notes Land Pattern 1. Ground / thermal vias are critical for the proper performance of this device. Vias should use a .35mm (#80 / .0135” ) diameter drill and have a final plated thru diameter of .25 mm (.010” ). 2. Add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. 3. Mounting screws can be added near the part to fasten the board to a heatsink. Ensure that the ground / thermal via region contacts the heatsink. 4. Do not put solder mask on the backside of the PC board in the region where the board contacts the heatsink. 5. RF trace width depends upon the PC board material and construction. 6. Use 1 oz. Copper minimum. 7. All dimensions are in millimeters (inches). Angles are in degrees. Specifications and information are subject to change without notice WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: [email protected] Web site: www.wj.com December 2004 Rev 1 ECG006 The Communications Edge TM Product Information InGaP HBT Gain Block ECG006B-G (Green / Lead-free SOT-89 Package) Mechanical Information This package is lead-free/Green/RoHS-compliant. It is compatible with both lead-free (maximum 260qC reflow temperature) and leaded (maximum 245qC reflow temperature) soldering processes. The plating material on the leads is NiPdAu. Product Marking Outline Drawing The component will be marked with an “ E006G” designator with an alphanumeric lot code on the top surface of the package. Tape and reel specifications for this part are located on the website in the “ Application Notes” section. MSL / ESD Rating ESD Rating: Value: Test: Standard: Land Pattern Class 1A Passes between 250 and 500V Human Body Model (HBM) JEDEC Standard JESD22-A114 MSL Rating: Level 3 at +260 C convection reflow Standard: JEDEC Standard J-STD-020 Mounting Config. Notes 1. Ground / thermal vias are critical for the proper performance of this device. Vias should use a .35mm (#80 / .0135” ) diameter drill and have a final plated thru diameter of .25 mm (.010” ). 2. Add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. 3. Mounting screws can be added near the part to fasten the board to a heatsink. Ensure that the ground / thermal via region contacts the heatsink. 4. Do not put solder mask on the backside of the PC board in the region where the board contacts the heatsink. 5. RF trace width depends upon the PC board material and construction. 6. Use 1 oz. Copper minimum. 7. All dimensions are in millimeters (inches). Angles are in degrees. Specifications and information are subject to change without notice WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: [email protected] Web site: www.wj.com December 2004 Rev 1 ECG006 The Communications Edge TM Product Information InGaP HBT Gain Block ECG006C (SOT-86 Package) Mechanical Information Outline Drawing Product Marking The component will be marked with a twodigit numeric lot code followed by an “ N” designator on the top surface of the package. Tape and reel specifications for this part are located on the website in the “ Application Notes” section. MSL / ESD Rating ESD Rating: Value: Test: Standard: Class 1A Passes between 250 and 500V Human Body Model (HBM) JEDEC Standard JESD22-A114 MSL Rating: Level 1 at +235 C convection reflow Standard: JEDEC Standard J-STD-020 Land Pattern Mounting Config. Notes 1. Ground / thermal vias are critical for the proper performance of this device. Vias should use a .35mm (#80 / .0135” ) diameter drill and have a final plated thru diameter of .25 mm (.010” ). 2. Add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. 3. Mounting screws can be added near the part to fasten the board to a heatsink. Ensure that the ground / thermal via region contacts the heatsink. 4. Do not put solder mask on the backside of the PC board in the region where the board contacts the heatsink. 5. RF trace width depends upon the PC board material and construction. 6. Use 1 oz. Copper minimum. 7. All dimensions are in millimeters (inches). Angles are in degrees. Specifications and information are subject to change without notice WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: [email protected] Web site: www.wj.com December 2004 Rev 1 ECG006 The Communications Edge TM Product Information InGaP HBT Gain Block ECG006F (SOT-363 Package) Mechanical Information Outline Drawing Product Marking The component will be marked with a twodigit numeric lot code (shown as “ XX” ) followed with a “ 3” designator on the top surface of the package. Tape and reel specifications for this part are located on the website in the “ Application Notes” section. MSL / ESD Rating ESD Rating: Value: Test: Standard: Class 1A Passes between 250 and 500V Human Body Model (HBM) JEDEC Standard JESD22-A114 MSL Rating: Level 3 at +235 C convection reflow Standard: JEDEC Standard J-STD-020 Mounting Config. Notes 1. Ground / thermal vias are critical for the proper performance of this device. Vias should use a .35mm (#80 / .0135” ) diameter drill and have a final plated thru diameter of .25 mm (.010” ). 2. Add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. 3. Mounting screws can be added near the part to fasten the board to a heatsink. Ensure that the ground / thermal via region contacts the heatsink. 4. Do not put solder mask on the backside of the PC board in the region where the board contacts the heatsink. 5. RF trace width depends upon the PC board material and construction. 6. Use 1 oz. Copper minimum. 7. All dimensions are in millimeters (inches). Angles are in degrees. Land Pattern Specifications and information are subject to change without notice WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: [email protected] Web site: www.wj.com December 2004 Rev 1 ECG006 The Communications Edge TM Product Information InGaP HBT Gain Block Typical Device S-Parameters – ECG006B / ECG006B-G S-Parameters (Vdevice = +3.9 V, ICC = 45 mA, T = 25 C, calibrated to device leads) Freq (MHz) 50 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 S11 (dB) S11 (ang) S21 (dB) S21 (ang) S12 (dB) S12 (ang) S22 (dB) S22 (ang) -16.18 -16.13 -15.97 -15.79 -15.34 -14.99 -14.73 -14.29 -13.38 -11.80 -9.66 -7.85 -6.37 -2.18 -22.13 -44.58 -68.38 -96.24 -124.42 -153.90 174.59 141.41 110.87 85.53 63.77 47.01 15.76 15.57 15.21 14.80 14.57 14.34 14.02 13.65 13.22 12.66 12.00 11.20 10.36 178.02 160.12 141.76 124.56 108.50 91.11 74.20 56.77 39.56 22.19 5.48 -10.89 -26.75 -18.89 -18.77 -18.46 -17.94 -17.29 -16.69 -16.16 -15.76 -15.49 -15.29 -15.28 -15.43 -15.69 -0.38 -2.87 -5.33 -9.45 -14.37 -21.48 -29.16 -38.37 -47.75 -57.59 -68.56 -79.10 -89.87 -14.36 -14.40 -14.15 -13.78 -13.23 -12.79 -12.22 -11.63 -10.44 -9.04 -7.50 -6.12 -4.95 -2.29 -26.41 -51.57 -77.30 -104.15 -131.75 -160.58 170.65 143.61 117.68 96.34 76.71 59.58 Typical Device S-Parameters – ECG006C S-Parameters (Vdevice = +3.9 V, ICC = 45 mA, T = 25 C, calibrated to device leads) Freq (MHz) 50 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 S11 (dB) S11 (ang) S21 (dB) S21 (ang) S12 (dB) S12 (ang) S22 (dB) S22 (ang) -13.66 -13.64 -14.11 -15.20 -17.86 -20.46 -18.86 -17.20 -16.45 -17.31 -16.22 -13.68 -11.01 -1.22 -13.39 -23.99 -35.45 -52.47 -93.43 -135.97 -158.47 -171.80 166.84 136.42 110.91 97.79 15.30 15.23 15.01 14.72 14.44 14.06 13.53 12.99 12.38 11.76 11.25 10.56 9.95 178.47 164.32 149.00 134.06 119.89 105.18 91.27 77.75 65.03 52.68 40.65 28.09 17.28 -18.67 -18.59 -18.38 -17.99 -17.52 -17.12 -16.59 -16.21 -15.93 -15.73 -15.52 -15.42 -15.43 -0.33 0.29 0.78 0.29 -0.93 -3.33 -6.24 -10.91 -15.16 -19.74 -24.35 -29.98 -34.96 -12.25 -12.33 -12.52 -13.08 -14.31 -15.20 -15.01 -14.89 -14.50 -13.75 -12.08 -10.21 -8.73 -1.92 -20.62 -41.41 -62.51 -82.78 -99.71 -124.98 -157.99 170.24 147.52 133.59 119.31 106.39 Typical Device S-Parameters – ECG006F S-Parameters (Vdevice = +3.9 V, ICC = 45 mA, T = 25 C, calibrated to device leads) Freq (MHz) 50 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 S11 (dB) S11 (ang) S21 (dB) S21 (ang) S12 (dB) S12 (ang) S22 (dB) S22 (ang) -16.22 -14.87 -16.45 -16.41 -14.08 -12.50 -12.18 -11.70 -10.97 -10.24 -9.06 -8.32 -7.84 -0.52 -18.97 -51.46 -95.69 -118.65 -114.48 -126.96 -139.53 -158.51 178.62 161.58 150.77 140.56 15.76 15.63 15.51 15.22 14.79 14.48 14.14 13.94 13.57 13.03 12.33 11.60 10.95 178.32 165.77 151.31 137.15 123.39 112.93 100.74 88.52 75.28 62.14 51.12 42.08 33.72 -18.82 -18.87 -18.40 -18.07 -17.74 -17.16 -16.80 -16.16 -15.72 -15.50 -15.19 -15.22 -15.14 -0.82 1.49 1.44 0.35 -1.31 -2.57 -4.49 -8.66 -12.48 -19.07 -24.71 -28.00 -30.97 -14.16 -12.83 -14.19 -14.59 -13.52 -13.05 -12.19 -11.93 -11.00 -9.10 -7.50 -6.87 -6.78 -2.06 -24.91 -55.98 -93.37 -120.99 -122.53 -138.80 -159.41 174.63 151.63 139.14 136.14 137.51 Device S-parameters are available for download off of the website at: http://www.wj.com Specifications and information are subject to change without notice WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: [email protected] Web site: www.wj.com December 2004 Rev 1