TI SN75146D

SN75146
DUAL DIFFERENTIAL LINE RECEIVER
SLLS015B – FEBRUARY 1986 – REVISED MAY 1995
D
D
D
D
D
D
D
D
D
D
Meets or Exceeds the Requirements of
ANSI EIA / TIA-422-B and -423-B
Meets or Exceeds the Requirements of
ANSI EIA / TIA-232-E and ITU
Recommendation V.28 With External
Components
Meets Federal Standards 1020 and 1030
Built-in 5-MHz Low-Pass Filter
Operates From Single 5-V Power Supply
Wide Common-Mode Voltage Range
High Input Impedance
TTL-Compatible Outputs
8-Pin Dual-in-Line Package
Pinout Compatible With the µA9637 and
µA9639
D OR P PACKAGE
(TOP VIEW)
VCC
1OUT
2OUT
GND
1
8
2
7
3
6
4
5
1IN +
1IN –
2IN +
2IN –
THE SN75146 IS NOT RECOMMENDED
FOR NEW DESIGNS.
description
The SN75146 is a dual differential line receiver designed to meet ANSI Standards EIA / TIA-422-B and -423-B.
The receiver is designed to have a constant impedance with input voltages of ± 3 V to ± 25 V allowing it to meet
the requirements of EIA / TIA-232-E and ITU recommendation V.28 with the addition of an external bias resistor.
This receiver is designed for low-speed operation below 355 kHz and has a built-in 5-MHz low-pass filter to
attenuate high-frequency noise. The inputs are compatible with either a single-ended or a differential line
system and the outputs are TTL compatible. This device operates from a single 5-V power supply and is
supplied in both the 8-pin dual-in-line and small-outline packages.
The SN75146 is characterized for operation from 0°C to 70°C.
logic symbol†
1IN +
1IN –
2IN +
2IN –
8
logic diagram
1IN +
2
7
6
5
3
1OUT
1IN –
2IN +
2OUT
2IN –
8
7
6
5
2
3
1OUT
2OUT
† This symbol is in accordance with ANSI/IEEE Std 91-1984 and
IEC Publication 617-12.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  1995, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SN75146
DUAL DIFFERENTIAL LINE RECEIVER
SLLS015B – FEBRUARY 1986 – REVISED MAY 1995
schematics of inputs and outputs
EQUIVALENT OF EACH INPUT
TYPICAL OF ALL OUTPUTS
VCC
VCC
50 Ω NOM
R1
740 Ω NOM
Input
7.41 R1
Output
7.4 kΩ NOM
740 Ω NOM
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to 7 V
Input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 25 V
Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 25 V
Output voltage range, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to 5.5 V
Low-level output current, IOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA
Continuous total dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential input voltage, are with respect to the network ground terminal.
2. Differential input voltage is measured at the noninverting input with respect to the corresponding inverting input.
DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25°C
POWER RATING
OPERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
D
725 mW
5.8 mW/°C
464 mW
P
1000 mW
8.0 mW/°C
640 mW
recommended operating conditions
Supply voltage, VCC
MIN
NOM
MAX
UNIT
4.75
5
5.25
V
Common-mode input voltage, VIC
Operating free-air temperature, TA
2
0
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
25
±7
V
70
°C
SN75146
DUAL DIFFERENTIAL LINE RECEIVER
SLLS015B – FEBRUARY 1986 – REVISED MAY 1995
electrical characteristics over recommended ranges of supply voltage, common-mode input
voltage, and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
– 0.2‡
VIT
Threshold input voltage (VIT + and VIT –)
Vhys
VIB
Hysteresis (VIT + – VIT –)
VOH
VOL
High-level output voltage
II = 0
VID = 0.2 V,
Low-level output voltage
VID = – 0.2 V,
ri
Input resistance
VI = 3 V to 25 V or VI = – 3 V to – 25 V,,
See Note 4
II
Input current
VCC = 0 to 5.5 V,,
See Note 5
TYP†
MAX
0.2
– 0.4‡
See Note 3
0.4
70
Input bias voltage
2.4
2.5
3.5
V
V
0.35
0.5
V
78
7.8
10 5
10.5
kΩ
6
VI = 10 V
VI = – 10 V
V
mV
2
IO = – 1 mA
IO = 20 mA
UNIT
1.1
3.25
– 1.6
– 3.25
mA
IOS
Short-circuit output current§
VO = 0,
VID = 0.2 V
– 40
– 75 – 100
mA
ICC
Supply current
VID = – 0.5 V,
No load
35
50
mA
† All typical values are at VCC = 5 V, TA = 25°C.
‡ The algebraic convention, in which the less positive (more negative) limit is designated as minimum, is used in this data sheet for threshold levels
only.
§ Only one output should be shorted at a time, and duration of the short circuit should not exceed one second.
NOTES: 3. The expanded threshold parameter is tested with a 500-Ω resistor in series with each input.
4. ri is defined by ∆VI/∆II.
5. The input not under test is grounded.
switching characteristics, VCC = 5 V, TA = 25°C
PARAMETER
tPLH
tPHL
TEST CONDITIONS
Propagation delay time, low-to-high-level output
Propagation delay time, high-to-low-level output
CL = 30 pF,
pF
See Figure 1
MIN
TYP
MAX
UNIT
100
150
300
ns
100
150
300
ns
PARAMETER MEASUREMENT INFORMATION
VCC +
Output
VCC +
0.5 V
392 Ω
Input
51 Ω
Input
(see Note B)
50%
50%
– 0.5 V
tPLH
tPHL
VOH
CL = 30 pF
(see Note A)
3.92 kΩ
Output
1.5 V
1.5 V
VOL
VOLTAGE WAVEFORMS
TEST CIRCUIT
NOTES: A. CL includes probe and jig capacitance.
B. The input pulse is supplied by a generator having the following characteristics: tr ≤ 5 ns, tf ≤ 5 ns, PRR ≤ 300 kHz,
duty cycle = 50%.
Figure 1. Test Circuit and Voltage Waveforms
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SN75146
DUAL DIFFERENTIAL LINE RECEIVER
SLLS015B – FEBRUARY 1986 – REVISED MAY 1995
TYPICAL CHARACTERISTICS
OUTPUT VOLTAGE
vs
DIFFERENTIAL INPUT VOLTAGE
OUTPUT VOLTAGE
vs
DIFFERENTIAL INPUT VOLTAGE
ÁÁ
ÁÁ
3
ÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏÏ
ÏÏÏÏÏ
4
VCC = 4.75 V
TA = 25°C
V
VO
O – Output Voltage – V
V
VO
O – Output Voltage – V
4
VIC = 0
VIC = ± 7 V
2
1
VIC = 0
0
– 100
3
VIC = 0
VIC = ± 7 V
2
ÁÁ
ÁÁ
VIC = ± 7 V
0
50
– 50
VID – Differential Input Voltage – mV
100
VCC = 5.25 V
TA = 25°C
1
VIC = ± 7 V
0
– 100
VIC = 0
0
50
– 50
VID – Differential Input Voltage – mV
Figure 2
4
Figure 3
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
100
SN75146
DUAL DIFFERENTIAL LINE RECEIVER
SLLS015B – FEBRUARY 1986 – REVISED MAY 1995
APPLICATION INFORMATION
12 V
5V
R
1/2 uA9636
1/2 SN75146
–12 V
See Note A
V
NOTE A: In order to meet the input-impedance and open-circuit-input voltage requirements of
ANSI Standard EIA/TIA-232-E and ITU recommendation V.28 and ensure
open-circuit-input fail-safe operation, R and V are selected to satisfy the following
equations:
V
+ –1.1–3.3 Rri
3 kW
ǒǓ
volts
v R )i r v 7 kW
R r
i
Figure 4. EIA/TIA-232-E System Applications
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
SN75146
DUAL DIFFERENTIAL LINE RECEIVER
SLLS015B – FEBRUARY 1986 – REVISED MAY 1995
APPLICATION INFORMATION
5V
Twisted Pair
5V
1/2 SN75146
1/2 uA9638AC
5V
1/2 SN75146
Figure 5. EIA/TIA-422-B System Applications
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright  1998, Texas Instruments Incorporated