SN75ALS191 DUAL DIFFERENTIAL LINE DRIVER SLLS032B – DECEMBER 1987 – REVISED MAY 1995 D D D D D D D OR P PACKAGE (TOP VIEW) Meets or Exceeds the Requirements of ANSI Standard EIA/TIA-422-B and ITU Recommendation V.11 Designed to Operate at 20 Mbaud or Higher TTL-and CMOS-Input Compatibility Single 5-V Supply Operation Output Short-Circuit Protection Improved Replacement for the µA9638 VCC 1A 2A GND 1 8 2 7 3 6 4 5 1Y 1Z 2Y 2Z description The SN75ALS191 is a dual, high-speed, differential line driver designed to meet ANSI Standard EIA/TIA-422-B and ITU Recommendation V.11. The inputs are TTL- and CMOS-compatible and have input clamp diodes. Schottky-diode-clamped transistors minimize propagation delay time. This device operates from a single 5-V power supply and is supplied in eight-pin packages. The SN75ALS191 is characterized for operation from 0°C to 70°C. FUNCTION TABLE (each driver) OUTPUTS INPUTS A Y H H L L L H Z H = high level, L = low level, Z = high impedance logic symbol† 1A 2A 2 3 logic diagram (positive logic) 8 8 1Y 7 1Z 6 2Y 5 2Z 2 1A 7 6 3 2A 5 1Y 1Z 2Y 2Z † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 1995, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN75ALS191 DUAL DIFFERENTIAL LINE DRIVER SLLS032B – DECEMBER 1987 – REVISED MAY 1995 schematics of inputs and outputs EQUIVALENT OF EACH INPUT TYPICAL OF ALL OUTPUTS VCC VCC 40 kΩ NOM Input 10 Ω Output GND absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Continuous total dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values except differential output voltage (VOD) are with respect to network ground terminal. DISSIPATION RATING TABLE TA ≤ 25°C POWER RATING DERATING FACTOR ABOVE TA = 25°C TA = 70°C POWER RATING D 725 mW 5.8 mW/°C 464 mW P 1000 mW 8.0 mW/°C 640 mW PACKAGE recommended operating conditions Supply voltage, VCC High-level input voltage, VIH MIN NOM MAX UNIT 4.75 5 5.25 V 2 Low-level input voltage, VIL High-level output current, IOH Low-level output current, IOL Operating free-air temperature, TA 2 0 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 V 0.8 V – 50 mA 50 mA 70 °C SN75ALS191 DUAL DIFFERENTIAL LINE DRIVER SLLS032B – DECEMBER 1987 – REVISED MAY 1995 electrical characteristics over operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS VIK Input clamp voltage VCC = 4.75 V, II = –18 mA VOH High level output voltage High-level VCC = 4.75 V, VIL = 0.8 V VIH = 2 V, VOL Low-level output voltage VCC = 4.75 V, IOL = 40 mA VIH = 2 V, |VOD1| Differential output voltage VCC = 5.25 V, IO = 0 |VOD2| Differential output voltage ∆ |VOD| Change in magnitude of differential output voltage ‡ VOC Common-mode output voltage§ ∆ |VOC| Change in magnitude of common-mode output voltage ‡ IO Output current with power off MIN IOH = – 10 mA 2.5 IOH = – 40 mA 2 TYP† MAX UNIT –1 – 1.2 V 3.3 V VIL = 0.8 V, 0.5 V 2 VOD2 V 2 V RL = 100 Ω,, VCC = 4.75 V to 5.25 V,, See Figure 1 VO = 6 V VO = – 0.25 V VCC = 0 Input current IIL IOS Low-level input current High-level input current Short-circuit output current¶ V 3 V ± 0.4 V 0.1 100 – 0.1 – 100 µA ± 100 VO = – 0.25 V to 6 V II IIH ± 0.4 50 µA VI = 2.7 V 25 µA VI = 0.5 V 200 µA – 150 mA VCC = 5.25 V, VCC = 5.25 V, VI = 5.5 V VCC = 5.25 V, VCC = 5.25 V, VO = 0 – 50 ICC Supply current (all drivers) VCC = 5.25 V, No load, All inputs at 0 V 32 40 mA † All typical values are at VCC = 5 V and TA = 25°C. ‡ | VOD | and | VOC | are the changes in magnitude of VOD and VOC, respectively, that occur when the input is changed from a high level to a low level. § In ANSI Standard EIA/TIA-422-B, VOC, which is the average of the two output voltages with respect to ground, is called output offset voltage, VOS. ¶ Only one output at a time should be shorted, and duration of the short circuit should not exceed one second. switching characteristics over recommended operating free-air temperature range, VCC = 5 V PARAMETER td(OD) tt(OD) TEST CONDITIONS Differential-output delay time Differential-output transition time CL = 15 pF, RL = 100 Ω, See Figure 2 Skew MIN TYP# MAX 3.5 7 ns 3.5 7 ns 1.5 4 ns UNIT # Typical values are at TA = 25°C. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 SN75ALS191 DUAL DIFFERENTIAL LINE DRIVER SLLS032B – DECEMBER 1987 – REVISED MAY 1995 PARAMETER MEASUREMENT INFORMATION 50 Ω Input VOD2 50 Ω VOC Figure 1. Differential and Common-Mode Output Voltages 3V Input 1.5 V 1.5 V Y Output 0V td(OD) td(OD) CL RL = 100 Ω Generator (see Note A) 50 Ω 90% Differential Output 10% 10% tt(OD) Z Output CL CL = 15 pF (see Note B) 90% tt(OD) VOH Y Output 50% Skew 50% VOL Skew VOH Z Output TEST CIRCUIT 50% 50% VOLTAGE WAVEFORMS NOTES: A. The input pulse generator has the following characteristics: ZO = 50 Ω, PRR ≤ 500 kHz, tw = 100 ns, tr = ≤ 5 ns. B. CL includes probe and jig capacitance. Figure 2. Test Circuit and Voltage Waveforms 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 VOL IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 1998, Texas Instruments Incorporated