TI TAS5508CPAG

TAS5508C
8-Channel Digital Audio PWM Processor
Data Manual
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Literature Number: SLES257
September 2010
TAS5508C
SLES257 – SEPTEMBER 2010
www.ti.com
Contents
1
2
3
2
............................................................................................................... 9
1.1
Features ...................................................................................................................... 9
1.2
Overview .................................................................................................................... 10
1.3
TAS5508C System Diagrams ............................................................................................ 12
Description ....................................................................................................................... 15
2.1
Physical Characteristics .................................................................................................. 15
2.1.1
Terminal Assignments ......................................................................................... 15
2.1.2
Ordering Information ........................................................................................... 15
2.1.3
PIN Descriptions ................................................................................................ 16
2.2
TAS5508C Functional Description ...................................................................................... 17
2.2.1
Power Supply ................................................................................................... 18
2.2.2
Clock, PLL, and Serial Data Interface ....................................................................... 18
2.2.2.1
Serial Audio Interface .............................................................................. 18
2
2.2.3
I C Serial-Control Interface ................................................................................... 19
2.2.4
Device Control .................................................................................................. 19
2.2.5
Digital Audio Processor (DAP) ................................................................................ 19
2.2.5.1
TAS5508C Audio-Processing Configurations .................................................. 19
2.2.5.2
TAS5508C Audio Signal-Processing Functions ................................................ 20
2.3
TAS5508C DAP Architecture ............................................................................................ 21
2.3.1
TAS5508C DAP Architecture Diagrams ..................................................................... 21
2.3.2
I 2C Coefficient Number Formats ............................................................................. 24
2.3.2.1
28-Bit 5.23 Number Format ....................................................................... 24
2.3.2.2
48-Bit 25.23 Number Format ..................................................................... 26
2.3.2.3
TAS5508C Audio Processing .................................................................... 27
2.4
Input Crossbar Mixer ...................................................................................................... 28
2.5
Biquad Filters .............................................................................................................. 28
2.6
Bass and Treble Controls ................................................................................................ 29
2.7
Volume, Automute, and Mute ............................................................................................ 30
2.8
Automute and Mute ....................................................................................................... 30
2.9
Loudness Compensation ................................................................................................. 31
2.9.1
Loudness Example ............................................................................................. 32
2.10 Dynamic Range Control (DRC) .......................................................................................... 33
2.10.1 DRC Implementation ........................................................................................... 36
2.10.2 Compression/Expansion Coefficient Computation Engine Parameters ................................. 36
2.10.2.1 Threshold Parameter Computation .............................................................. 37
2.10.2.2 Offset Parameter Computation ................................................................... 37
2.10.2.3 Slope Parameter Computation ................................................................... 38
2.11 Output Mixer ............................................................................................................... 38
2.12 PWM ........................................................................................................................ 39
2.12.1 DC Blocking (High-Pass Enable/Disable) ................................................................... 40
2.12.2 De-Emphasis Filter ............................................................................................. 40
2.12.3 Power-Supply Volume Control (PSVC) ...................................................................... 40
2.12.4 AM Interference Avoidance ................................................................................... 41
TAS5508C Controls and Status ........................................................................................... 43
3.1
I2C Status Registers ....................................................................................................... 43
3.1.1
General Status Register (0x01) ............................................................................... 43
Introduction PWM
Contents
Copyright © 2010, Texas Instruments Incorporated
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
3.2
3.1.2
Error Status Register (0x02) .................................................................................. 43
TAS5508C Pin Controls .................................................................................................. 43
................................................................................................. 43
3.2.2
Power Down (PDN) ............................................................................................ 45
3.2.3
Back-End Error (BKND_ERR) ................................................................................ 46
3.2.4
Speaker/Headphone Selector (HP_SEL) .................................................................... 46
3.2.5
Mute (MUTE) .................................................................................................... 46
3.3
Device Configuration Controls ........................................................................................... 47
3.3.1
Channel Configuration Registers ............................................................................. 47
3.3.2
Headphone Configuration Registers ......................................................................... 48
3.3.3
Audio System Configurations ................................................................................. 48
3.3.3.1
Using Line Outputs in 6-Channel Configurations .............................................. 49
3.3.4
Recovery from Clock Error .................................................................................... 49
3.3.5
Power-Supply Volume-Control Enable ....................................................................... 49
3.3.6
Volume and Mute Update Rate ............................................................................... 49
3.3.7
Modulation Index Limit ......................................................................................... 50
3.3.8
Interchannel Delay .............................................................................................. 50
3.4
Master Clock and Serial Data Rate Controls .......................................................................... 50
3.4.1
PLL Operation ................................................................................................... 51
3.5
Bank Controls .............................................................................................................. 51
3.5.1
Manual Bank Selection ........................................................................................ 52
3.5.2
Automatic Bank Selection ..................................................................................... 52
3.5.2.1
Coefficient Write Operations While Automatic Bank Switch Is Enabled .................... 52
3.5.3
Bank Set ......................................................................................................... 52
3.5.4
Bank-Switch Timeline .......................................................................................... 52
3.5.5
Bank-Switching Example 1 .................................................................................... 53
3.5.6
Bank-Switching Example 2 .................................................................................... 53
Electrical Specifications ..................................................................................................... 55
4.1
Absolute Maximum Ratings .............................................................................................. 55
4.2
Dissipation Rating Table (High-k Board, 105°C Junction) ........................................................... 55
4.3
Dynamic Performance At Recommended Operating Conditions at 25°C .......................................... 55
4.4
Recommended Operating Conditions .................................................................................. 55
4.5
Electrical Characteristics ................................................................................................. 56
4.6
PWM Operation ............................................................................................................ 56
4.7
Switching Characteristics ................................................................................................. 56
4.7.1
Clock Signals .................................................................................................... 56
4.7.2
Serial Audio Port ................................................................................................ 57
4.7.3
I2C Serial Control Port Operation ............................................................................. 58
4.7.4
Reset Timing (RESET) ......................................................................................... 59
4.7.5
Power-Down (PDN) Timing ................................................................................... 59
4.7.6
Back-End Error (BKND_ERR) ................................................................................ 60
4.7.7
Mute Timing (MUTE) ........................................................................................... 60
4.7.8
Headphone Select (HP_SEL) ................................................................................. 61
4.7.9
Volume Control ................................................................................................. 62
4.8
Serial Audio Interface Control and Timing ............................................................................. 62
4.8.1
I 2S Timing ....................................................................................................... 62
4.8.2
Left-Justified Timing ............................................................................................ 63
3.2.1
4
Reset (RESET)
Copyright © 2010, Texas Instruments Incorporated
Contents
3
TAS5508C
SLES257 – SEPTEMBER 2010
.......................................................................................... 64
.................................................................. 65
5.1
General I2C Operation .................................................................................................... 65
5.2
Single- and Multiple-Byte Transfers ..................................................................................... 65
5.3
Single-Byte Write .......................................................................................................... 66
5.4
Multiple-Byte Write ........................................................................................................ 66
5.5
Incremental Multiple-Byte Write ......................................................................................... 67
5.6
Single-Byte Read .......................................................................................................... 67
5.7
Multiple-Byte Read ........................................................................................................ 68
Serial-Control I2C Register Summary ................................................................................... 69
Serial-Control Interface Register Definitions ......................................................................... 73
7.1
Clock Control Register (0x00) ........................................................................................... 73
7.2
General Status Register 0 (0x01) ....................................................................................... 73
7.3
Error Status Register (0x02) ............................................................................................. 74
7.4
System Control Register 1 (0x03) ....................................................................................... 74
7.5
System Control Register 2 (0x04) ....................................................................................... 74
7.6
Channel Configuration Control Registers (0x05–0x0C) .............................................................. 74
7.7
Headphone Configuration Control Register (0x0D) ................................................................... 75
7.8
Serial Data Interface Control Register (0x0E) ......................................................................... 75
7.9
Soft Mute Register (0x0F) ................................................................................................ 76
7.10 Automute Control Register (0x14) ....................................................................................... 77
7.11 Automute PWM Threshold and Back-End Reset Period Register (0x15) .......................................... 78
7.12 Modulation Index Limit Register (0x16) ................................................................................. 79
7.13 Interchannel Delay Registers (0x1B–0x22) ............................................................................ 79
7.14 Channel Offset Register (0x23) .......................................................................................... 79
7.15 Bank-Switching Command Register (0x40) ............................................................................ 80
7.16 Input Mixer Registers, Channels 1–8 (0x41–0x48) ................................................................... 80
7.17 Bass Management Registers (0x49–0x50) ............................................................................ 84
7.18 Biquad Filter Register (0x51–0x88) ..................................................................................... 84
7.19 Bass and Treble Bypass Register, Channels 1–8 (0x89–0x90) ..................................................... 85
7.20 Loudness Registers (0x91–0x95) ....................................................................................... 85
7.21 DRC1 Control Registers, Channels 1–7 (0x96) ....................................................................... 86
7.22 DRC2 Control Register, Channel 8 (0x97) ............................................................................. 87
7.23 DRC1 Data Registers (0x98–0x9C) ..................................................................................... 87
7.24 DRC2 Data Registers (0x9D–0xA1) .................................................................................... 88
7.25 DRC Bypass Registers (0xA2–0xA9) ................................................................................... 88
7.26 8×2 Output Mixer Registers (0xAA–0xAF) ............................................................................. 88
7.27 8×3 Output Mixer Registers (0xB0–0xB1) ............................................................................. 89
7.28 Volume Biquad Register (0xCF) ......................................................................................... 91
7.29 Volume, Treble, and Bass Slew Rates Register (0xD0) ............................................................. 92
7.30 Volume Registers (0xD1–0xD9) ......................................................................................... 92
7.31 Bass Filter Set Register (0xDA) ......................................................................................... 94
7.32 Bass Filter Index Register (0xDB) ....................................................................................... 95
7.33 Treble Filter Set Register (0xDC) ....................................................................................... 96
7.34 Treble Filter Index (0xDD) ................................................................................................ 97
7.35 AM Mode Register (0xDE) ............................................................................................... 97
4.8.3
5
6
7
4
www.ti.com
Right-Justified Timing
I2C Serial-Control Interface (Slave Address 0x36)
Contents
Copyright © 2010, Texas Instruments Incorporated
TAS5508C
www.ti.com
8
SLES257 – SEPTEMBER 2010
........................................................................................... 99
........................................................................................ 99
7.38 Incremental Multiple-Write Append Register (0xFE) .................................................................. 99
TAS5508C Example Application Schematic ......................................................................... 101
7.36
PSVC Range Register (0xDF)
7.37
General Control Register (0xE0)
Copyright © 2010, Texas Instruments Incorporated
Contents
5
TAS5508C
SLES257 – SEPTEMBER 2010
www.ti.com
List of Figures
1-1
TAS5508C Functional Structure................................................................................................ 12
1-2
Typical TAS5508C Application (DVD Receiver)
1-3
2-1
2-2
2-3
2-4
2-5
2-6
2-7
2-8
2-9
2-10
2-11
2-12
2-13
2-14
2-15
2-16
2-17
2-18
2-19
2-20
2-21
2-22
4-1
4-2
4-3
4-4
4-5
4-6
4-7
4-8
4-9
4-10
4-11
5-1
5-2
5-3
5-4
5-5
6
.............................................................................
Recommended TAS5508C and TAS5121 Channel Configuraton .........................................................
TAS5508C DAP Architecture With I2C Registers (Fs ≤ 96 kHz) ...........................................................
TAS5508C Architecture With I2C Registers (Fs = 176.4 kHz or Fs = 192 kHz) .........................................
TAS5508C Detailed Channel Processing .....................................................................................
5.23 Format .......................................................................................................................
Conversion Weighting Factors—5.23 Format to Floating Point ............................................................
Alignment of 5.23 Coefficient in 32-Bit I2C Word.............................................................................
25.23 Format ......................................................................................................................
Alignment of 5.23 Coefficient in 32-Bit I2C Word.............................................................................
Alignment of 25.23 Coefficient in Two 32-Bit I2C Words ....................................................................
TAS5508C Digital Audio Processing ..........................................................................................
Input Crossbar Mixer .............................................................................................................
Biquad Filter Structure ...........................................................................................................
Automute Threshold .............................................................................................................
Loudness Compensation Functional Block Diagram ........................................................................
Loudness Example Plots ........................................................................................................
DRC Positioning in TAS5508C Processing Flow ............................................................................
Dynamic Range Compression (DRC) Transfer Function Structure ........................................................
Output Mixers .....................................................................................................................
De-Emphasis Filter Characteristics ............................................................................................
Power-Supply and Digital Gains (Log Space) ................................................................................
Power-Supply and Digital Gains (Linear Space) .............................................................................
Block Diagrams of Typical Systems Requiring TAS5508C Automatic AM Interference-Avoidance Circuit ..........
Slave Mode Serial Data Interface Timing .....................................................................................
SCL and SDA Timing ............................................................................................................
Start and Stop Conditions Timing ..............................................................................................
Reset Timing ......................................................................................................................
Power-Down Timing .............................................................................................................
Error Recovery Timing ...........................................................................................................
Mute Timing .......................................................................................................................
HP_SEL Timing...................................................................................................................
I2S 64-Fs Format .................................................................................................................
Left-Justified 64-Fs Format .....................................................................................................
Right-Justified 64-Fs Format ....................................................................................................
Typical I2C Sequence ............................................................................................................
Single-Byte Write Transfer ......................................................................................................
Multiple-Byte Write Transfer ....................................................................................................
Single-Byte Read Transfer ......................................................................................................
Multiple-Byte Read Transfer ....................................................................................................
List of Figures
12
13
23
24
24
25
25
25
26
26
27
28
28
29
31
32
33
34
35
39
40
41
41
42
57
58
58
59
59
60
60
62
63
63
64
65
66
67
68
68
Copyright © 2010, Texas Instruments Incorporated
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
List of Tables
2-1
Serial Data Formats .............................................................................................................. 19
2-2
TAS5508C Audio Processing Feature Sets
2-3
2-4
2-5
2-6
2-7
2-8
3-1
3-2
3-3
3-4
3-5
3-6
3-7
3-8
3-9
7-1
7-2
7-3
7-4
7-5
7-6
7-7
7-8
7-9
7-10
7-11
7-12
7-13
7-14
7-15
7-16
7-17
7-18
7-19
7-20
7-21
7-22
7-23
7-24
7-25
7-26
7-27
7-28
7-29
7-30
..................................................................................
Contents of One 20-Byte Biquad Filter Register (Default = All-Pass) .....................................................
Bass and Treble Filter Selections ..............................................................................................
Linear Gain Step Size ...........................................................................................................
Default Loudness Compensation Parameters ................................................................................
Loudness Function Parameters ................................................................................................
DRC Recommended Changes From TAS5508C Defaults .................................................................
Device Outputs During Reset ...................................................................................................
Values Set During Reset ........................................................................................................
Device Outputs During Power Down ..........................................................................................
Device Outputs During Back-End Error .......................................................................................
Description of the Channel Configuration Registers (0x05 to 0x0C) ......................................................
Recommended TAS5508C Configurations for Texas Instruments Power Stages .......................................
Audio System Configuration (General Control Register 0xE0) .............................................................
Volume Ramp Rates in ms .....................................................................................................
Interchannel Delay Default Values .............................................................................................
Clock Control Register Format .................................................................................................
General Status Register Format................................................................................................
Error Status Register Format ...................................................................................................
System Control Register 1 Format .............................................................................................
System Control Register 2 Format .............................................................................................
Channel Configuration Control Register Format .............................................................................
Headphone Configuration Control Register Format .........................................................................
Serial Data Interface Control Register Format ...............................................................................
Soft Mute Register Format ......................................................................................................
Automute Control Register Format.............................................................................................
Automute PWM Threshold and Back-End Reset Period Register Format................................................
Modulation Index Limit Register Format ......................................................................................
Interchannel Delay Register Format ...........................................................................................
Channel Offset Register Format................................................................................................
Bank-Switching Command Register Format ..................................................................................
Channel 1–8 Input Mixer Register Format ....................................................................................
Bass Management Register Format ...........................................................................................
Biquad Filter Register Format ..................................................................................................
Contents of One 20-Byte Biquad Filter Register (Default = All-Pass) .....................................................
Channel 1–8 Bass and Treble Bypass Register Format ....................................................................
Loudness Register Format ......................................................................................................
Channel 1–7 DCR1 Control Register Format.................................................................................
Channel-8 DRC2 Control Register Format ...................................................................................
DRC1 Data Register Format ....................................................................................................
DRC2 Data Register Format ....................................................................................................
DRC Bypass Register Format ..................................................................................................
Output Mixer Register Format (Upper 4 Bytes) ..............................................................................
Output Mixer Register Format (Lower 4 Bytes) ..............................................................................
Output Mixer Register Format (Upper 4 Bytes) ..............................................................................
Output Mixer Register Format (Middle 4 Bytes) ..............................................................................
Copyright © 2010, Texas Instruments Incorporated
List of Tables
21
29
30
30
32
33
34
43
44
45
46
47
48
49
50
50
73
73
74
74
74
75
75
75
76
77
78
79
79
79
80
81
84
84
85
85
85
86
87
87
88
88
89
89
90
90
7
TAS5508C
SLES257 – SEPTEMBER 2010
www.ti.com
7-31
Output Mixer Register Format (Lower 4 Bytes) .............................................................................. 90
7-32
Volume Biquad Register Format (Default = All-Pass) ....................................................................... 91
7-33
Volume Gain Update Rate (Slew Rate) ....................................................................................... 92
7-34
Treble and Bass Gain Step Size (Slew Rate) ................................................................................ 92
7-35
Volume Register Format
7-36
Master and Individual Volume Controls ....................................................................................... 93
7-37
Channel 8 (Subwoofer) .......................................................................................................... 94
7-38
Channels 6 and 5 (Right and Left Lineout in 6-Channel Configuration; Right and Left Surround in 8-Channel
Configuration) ..................................................................................................................... 94
7-39
Channels 4 and 3 (Right and Left Rear) ...................................................................................... 94
7-40
Channels 7, 2, and 1 (Center, Right Front, and Left Front)................................................................. 95
7-41
Bass Filter Index Register Format
7-42
Bass Filter Indexes ............................................................................................................... 95
7-43
Channel 8 (Subwoofer) .......................................................................................................... 96
7-44
Channels 6 and 5 (Right and Left Lineout in 6-Channel Configuration; Right and Left Surround in 8-Channel
Configuration) ..................................................................................................................... 96
7-45
Channels 4 and 3 (Right and Left Rear) ...................................................................................... 96
7-46
Channels 7, 2, and 1 (Center, Right Front, and Left Front)................................................................. 96
7-47
Treble Filter Index Register Format ............................................................................................ 97
7-48
Treble Filter Indexes ............................................................................................................. 97
7-49
AM Mode Register Format ...................................................................................................... 97
7-50
AM Tuned Frequency Register in BCD Mode (Lower 2 Bytes of 0xDE) .................................................. 98
7-51
AM Tuned Frequency Register in Binary Mode (Lower 2 Bytes of 0xDE) ................................................ 98
7-52
PSVC Range Register Format
7-53
8
........................................................................................................
.............................................................................................
.................................................................................................
General Control Register Format ..............................................................................................
List of Tables
92
95
99
99
Copyright © 2010, Texas Instruments Incorporated
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
8-Channel Digital Audio PWM Processor
Check for Samples: TAS5508C
1
Introduction PWM
1.1
Features
1234
• General Features
– Automated Operation With an Easy-to-Use
Control Interface
– I2C Serial-Control Slave Interface
– Integrated AM Interference-Avoidance
Circuitry
– Single, 3.3-V Power Supply
– 64-Pin TQFP Package
– 5-V Tolerant Inputs
• Audio Input/Output
– Automatic Master Clock Rate and Data
Sample Rate Detection
– Eight Serial Audio Input Channels
– Eight PWM Audio Output Channels
Configurable as Six Channels With Stereo
Lineout or Eight Channels
– Line Output Is a PWM Output to Drive an
External Differential-Input Operational
Amplifier
– Headphone PWM Output to Drive an External
Differential Amplifier Like the TPA112
– PWM Outputs Support Single-Ended and
Bridge-Tied Loads
– 32-, 38-, 44.1-, 48-, 88.2-, 96-, 176.4-, and
192-kHz Sampling Rates
– Data Formats: 16-, 20-, or 24-Bit
Left-Justified, I2S, or Right-Justified Input
Data
– 64-Fs Bit-Clock Rate
– 128-, 192-, 256-, 384-, 512-, and 768-Fs
Master Clock Rates (Up to a Maximum of
50 MHz)
• Audio Processing
– 48-Bit Processing Architecture With 76 Bits
of Precision for Most Audio Processing
Features
– Volume Control Range 36 dB to –127 dB
• Master Volume Control Range of 18 dB to
–100 dB
• Eight Individual Channel Volume Control
Ranges of 18 dB to –127 dB
– Programmable Soft Volume and Mute
Update Rates
– Four Bass and Treble Tone Controls with
±18-dB Range, Selectable Corner
Frequencies, and Second-Order Slopes
• L, R, and C
• LS, RS
• LR, RR
• Sub
– Configurable Loudness Compensation
– Two Dynamic Range Compressors With Two
Thresholds, Two Offsets, and Three Slopes
– Seven Biquads Per Channel
– Full 8×8 Input Crossbar Mixer. Each
Signal-Processing Channel Input Can Be
Any Ratio of the Eight Input Channels.
– 8×2 Output Mixer – Channels 1–6. Each
Output Can Be Any Ratio of Any Two
Signal-Processed Channels.
– 8×3 Output Mixer – Channels 7 and 8. Each
Output Can Be Any Ratio of Any Three
Signal-Processed Channels.
– Three Coefficient Sets Stored on the Device
Can Be Selected Manually or Automatically
(Based on Specific Data Rates).
– DC Blocking Filters
– Able to Support a Variety of Bass
Management Algorithms
• PWM Processing
– 32-Bit Processing PWM Architecture With 40
Bits of Precision
– 8× Oversampling With Fifth-Order Noise
Shaping at 32 kHz–48 kHz, 4× Oversampling
at 88.2 kHz and 96 kHz, and 2× Oversampling
at 176.4 kHz and 192 kHz
– >102-dB Dynamic Range
– THD+N < 0.1%
– 20-Hz–20-kHz, Flat Noise Floor for 44.1-, 48-,
88.2-, 96-, 176.4-, and 192-kHz Data Rates
– Digital De-Emphasis for 32-, 44.1-, and
48-kHz Data Rates
– Flexible Automute Logic With Programmable
Threshold and Duration for Noise-Free
1
2
3
4
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PurePath Digital is a trademark of Texas Instruments.
Matlab is a trademark of Math Works, Inc.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2010, Texas Instruments Incorporated
TAS5508C
SLES257 – SEPTEMBER 2010
www.ti.com
Operation
– Intelligent AM Interference-Avoidance
System Provides Clear AM Reception
– Power-Supply Volume Control (PSVC)
1.2
Support for Enhanced Dynamic Range in
High-Performance Applications
– Adjustable Modulation Limit
Overview
The TAS5508C is an 8-channel digital pulse-width modulator (PWM) that provides both advanced
performance and a high level of system integration. The TAS5508C is designed to interface seamlessly
with most audio digital signal processors. The TAS5508C automatically adjusts control configurations in
response to clock and data rate changes and idle conditions. This enables the TAS5508C to provide an
easy-to-use control interface with relaxed timing requirements.
The TAS5508C can drive eight channels of H-bridge power stages. Texas Instruments H-bridge parts
TAS5111, TAS5112, or TAS5182 with FETs are designed to work seamlessly with the TAS5508C. The
TAS5508C supports both single-ended or bridge-tied load configurations. The TAS5508C also provides a
high-performance, differential output to drive an external, differential-input, analog headphone amplifier
(such as the TPA112).
The TAS5508C uses AD modulation operating at a 384-kHz switching rate for 48-, 96-, and 192-kHz data.
The 8× oversampling combined with the fifth-order noise shaper provides a broad, flat noise floor and
excellent dynamic range from 20 Hz to 20 kHz.
The TAS5508C is a clocked slave-only device. The TAS5508C receives MCLK, SCLK, and LRCLK from
other system components. The TAS5508C accepts master clock rates of 128, 192, 256, 384, 512, and
768 Fs. The TAS5508C accepts a 64-Fs bit clock.
The TAS5508C allows for extending the dynamic range by providing a power-supply volume control
(PSVC) output signal.
10
Introduction PWM
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
MUTE
HP_SEL
BKND_ERR
RESET
PDN
SCL
I2 C
Serial
Control
I/F
Clock, PLL, and Serial Data I/F
SDA
SDIN1
SDIN2
SDIN3
SDIN4
PLL_FLTM
PLL_FLTP
OSC CAP
SCLK
LRCLK
MCLK
XTL_OUT
XTL_IN
AVSS
AVDD
DVSS
DVDD
VRD_PLL
VRA_PLL
VBGAP
AVDD_REF
AVSS_PLL
AVDD_PLL
VR_PLL
Device
Control
Power Supply
8 × 8 Crossbar Mixer
8
9
DAP Control
4
Volume
Control
8
8
2
2
8
8
DC
De Interpolate SRC NS PWM
Block Emph
0
7
Soft Soft Loud
Det Biquads Tone Vol Comp DRC
DC
De Interpolate SRC NS PWM
Block Emph
DC
De Interpolate SRC NS PWM
Block Emph
DC
De Interpolate SRC NS PWM
Block Emph
DC
De Interpolate SRC NS PWM
Block Emph
DC
De Interpolate SRC NS PWM
Block Emph
DC
De Interpolate SRC NS PWM
Block Emph
PWM Section
DC
De Interpolate SRC NS PWM
Block Emph
8 × 2 Crossbar Mixer
0
7
Soft Soft Loud
Det Biquads Tone Vol Comp DRC
0
7
Soft Soft Loud
Det Biquads Tone Vol Comp DRC
0
7
Soft Soft Loud
Det Biquads Tone Vol Comp DRC
0
7
Soft Soft Loud
Det Biquads Tone Vol Comp DRC
0
7
Soft Soft Loud
Det Biquads Tone Vol Comp DRC
0
7
Soft Soft Loud DRC
Det Biquads Tone Vol Comp
0
7
Soft Soft Loud
Det Biquads Tone Vol Comp DRC
Digital Audio Processor
PSVC
PSVC
VALID
PWM AP and AM6 R Surround
PWM R Lineout
PWM AP and AM5 L Surround
PWM L Lineout
PWM AP and AM8
Subwoofer
PWM AP and AM7 Center
PWM AP and AM4 R Rear
PWM AP and AM3 L Rear
PWM AP and AM2 R Front
PWM AP and AM1 L Front
PWM_HPP and MR
PWM_HPP and ML
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
Output Control
PWM Control
System Control
B0011-01
Figure 1-1. TAS5508C Functional Structure
Introduction PWM
11
TAS5508C
SLES257 – SEPTEMBER 2010
1.3
www.ti.com
TAS5508C System Diagrams
Typical applications for the TAS5508C are 6- to 8-channel audio systems such as DVD or AV receivers.
Figure 1-2 shows the basic system diagram of the DVD receiver.
Power Supply
AM
FM
T uner
T exas Instruments
Digital Audio Amplifier
T AS5508C
DVD Loader
MPEG Decoder
Front-Panel Controls
Figure 1-2. Typical TAS5508C Application (DVD Receiver)
Figure 1-3 shows the recommended channel configuration when using the TAS5508C with the TAS5121
power stage. Note that each channel is normally dedicated to a particular function.
12
Introduction PWM
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
TAS5508C
Figure 1-3. Recommended TAS5508C and TAS5121 Channel Configuraton
Introduction PWM
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
13
TAS5508C
SLES257 – SEPTEMBER 2010
14
www.ti.com
Introduction PWM
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
2
Description
2.1
Physical Characteristics
2.1.1
Terminal Assignments
RESEVED
MCLK
PWM_HPPR
PWM_HPMR
PWM_HPPL
PWM_HPML
PWM_P_6
PWM_M_6
PWM_P_5
PWM_M_5
DVDD_PWM
DVSS_PWM
PWM_P_8
PWM_M_8
PWM_P_7
PWM_M_7
PAG PACKAGE
(TOP VIEW)
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
VRA_PLL
PLL_FLT_RET
PLL_FLTM
PLL_FLTP
AVSS
AVSS
VRD_PLL
AVSS_PLL
AVDD_PLL
VBGAP
RESET
HP_SEL
PDN
MUTE
DVDD
DVSS
1
48
2
47
3
46
4
45
5
44
6
43
7
42
8
41
9
40
10
39
11
38
12
37
13
36
14
35
15
34
16
33
VR_PWM
PWM_P_4
PWM_M_4
PWM_P_3
PWM_M_3
PWM_P_2
PWM_M_2
PWM_P_1
PWM_M_1
VALID
DVSS
BKND_ERR
DVDD
DVSS
DVSS
VR_DIG
VR_DPLL
OSC_CAP
XTL_OUT
XTL_IN
RESERVED
RESERVED
RESERVED
SDA
SCL
LRCLK
SCLK
SDIN4
SDIN3
SDIN2
SDIN1
PSVC
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
P0010-01
2.1.2
Ordering Information
TA
PLASTIC 64-PIN PQFP (PN)
0°C to 70°C
TAS5508CPAG
Description
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
15
TAS5508C
SLES257 – SEPTEMBER 2010
2.1.3
www.ti.com
PIN Descriptions
PIN
NAME
NO.
AVDD_PLL
TYPE (1)
5-V
TOLERANT
TERMINATION (2)
DESCRIPTION
9
P
3.3-V analog power supply for PLL. This terminal can be connected to the same
power source used to drive power terminal DVDD, but to achieve low PLL jitter,
this terminal should be bypassed to AVSS_PLL with a 0.1-mF low-ESR
capacitor.
5, 6
P
Analog ground
AVSS_PLL
8
P
Analog ground for PLL. This terminal should reference the same ground as
terminal DVSS, but to achieve low PLL jitter, ground noise at this terminal must
be minimized. The availability of the AVSS terminal allows a designer to use
optimizing techniques such as star ground connections, separate ground planes,
or other quiet ground-distribution techniques to achieve a quiet ground reference
at this terminal.
BKND_ERR
37
DI
15, 36
P
3.3-V digital power supply
54
P
3.3-V digital power supply for PWM
16, 34,
35, 38
P
Digital ground
AVSS
DVDD
DVDD_PWM
DVSS
Pullup
Active-low. A back-end error sequence is generated by applying logic low to this
terminal. The BKND_ERR results in no change to any system parameters, with
all H-bridge drive signals going to a hard-mute (M) state.
DVSS_PWM
53
P
HP_SEL
12
DI
5V
LRCLK
26
DI
5V
MCLK
63
DI
5V
Pulldown
MCLK is a 3.3-V master clock input. The input frequency of this clock can range
from 4 MHz to 50 MHz.
MUTE
14
DI
5V
Pullup
Soft mute of outputs, active-low (muted signal = a logic low, normal operation =
a logic high). The mute control provides a noiseless volume ramp to silence.
Releasing mute provides a noiseless ramp to previous volume.
OSC_CAP
18
AO
PDN
13
DI
5V
Pullup
PLL_FLT_RET
2
AO
PLL external filter return
PLL_FLTM
3
AO
PLL negative input. Connected to PLL_FLT_RTN via an RC network
PLL_FLTP
4
AI
PLL positive input. Connected to PLL_FLT_RTN via an RC network
PSVC
32
O
Power-supply volume control PWM output
PWM_HPML
59
DO
PWM left-channel headphone (differential –)
PWM_HPMR
61
DO
PWM right-channel headphone (differential –)
PWM_HPPL
60
DO
PWM left-channel headphone (differential +)
PWM_HPPR
62
DO
PWM right-channel headphone (differential +)
PWM_M_1
40
DO
PWM 1 output (differential –)
PWM_M_2
42
DO
PWM 2 output (differential –)
PWM_M_3
44
DO
PWM 3 output (differential –)
PWM_M_4
46
DO
PWM 4 output (differential –)
PWM_M_5
55
DO
PWM 5 output (differential –)
PWM_M_6
57
DO
PWM 6 output (differential –)
PWM_M_7
49
DO
PWM 7 (lineout L) output (differential –)
PWM_M_8
51
DO
PWM 8 (lineout R) output (differential –)
PWM_P_1
41
DO
PWM 1 output (differential +)
PWM_P_2
43
DO
PWM 2 output (differential +)
PWM_P_3
45
DO
PWM 3 output (differential +)
PWM_P_4
47
DO
PWM 4 output (differential +)
(1)
(2)
16
Digital ground for PWM
Pullup
Headphone in/out selector. When a logic low is applied, the headphone is
selected (speakers are off). When a logic high is applied, speakers are selected
(headphone is off).
Serial-audio data left/right clock (sampling-rate clock)
Oscillator capacitor
Power down, active-low. PDN powers down all logic and stops all clocks
whenever a logic low is applied. The internal parameters are preserved through
a power-down cycle, as long as RESET is not active. The duration for system
recovery from power down is 100 ms.
Type: A = analog; D = 3.3-V digital; P = power/ground/decoupling; I = input; O = output
All pullups are 200-mA weak pullups and all pulldowns are 200-mA weak pulldowns. The pullups and pulldowns are included to ensure
proper input logic levels if the terminals are left unconnected (pullups => logic-1 input; pulldowns => logic-0 input). Devices that drive
inputs with pullups must be able to sink 200 mA, while maintaining a logic-0 drive level. Devices that drive inputs with pulldowns must be
able to source 200 mA, while maintaining a logic-1 drive level.
Description
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
PIN
NAME
NO.
TYPE (1)
5-V
TOLERANT
TERMINATION (2)
DESCRIPTION
PWM_P_5
56
DO
PWM 5 output (differential +)
PWM_P_6
58
DO
PWM 6 output (differential +)
PWM_P_7
50
DO
PWM 7 (lineout L) output (differential +)
PWM_P_8
52
DO
PWM 8 (lineout R) output (differential +)
RESERVED
21, 22,
23, 64
Connect to digital ground
RESET
11
DI
5V
SCL
25
DI
5V
I2C serial-control clock input/output
SCLK
27
DI
5V
Serial-audio data clock (shift clock) input
SDA
24
DIO
5V
I2C serial-control data-interface input/output
SDIN1
31
DI
5V
Pulldown
Serial-audio data input 1 is one of the serial-data input ports. SDIN1 supports
four discrete (stereo) data formats and is capable of inputting data at 64 Fs.
SDIN2
30
DI
5V
Pulldown
Serial-audio data input 2 is one of the serial-data input ports. SDIN2 supports
four discrete (stereo) data formats and is capable of inputting data at 64 Fs.
SDIN3
29
DI
5V
Pulldown
Serial-audio data input 3 is one of the serial-data input ports. SDIN3 supports
four discrete (stereo) data formats and is capable of inputting data at 64 Fs.
SDIN4
28
DI
5V
Pulldown
Serial-audio data input 4 is one of the serial-data input ports. SDIN4 supports
four discrete (stereo) data formats and is capable of inputting data at 64 Fs.
VALID
39
DO
VBGAP
10
P
Band-gap voltage reference. A pinout of the internally regulated 1.2-V reference.
Typically has a 1-nF low-ESR capacitor between VBGAP and AVSS_PLL. This
terminal must not be used to power external devices.
VR_DIG
33
P
Voltage reference for 1.8-V digital core supply. A pinout of the internally
regulated 1.8-V power used by digital core logic. A 4.7-mF low-ESR capacitor (3)
should be connected between this terminal and DVSS. This terminal must not
be used to power external devices.
VR_DPLL
17
P
Voltage reference for 1.8-V digital PLL supply. A pinout of the internally
regulated 1.8-V power used by digital PLL logic. A 0.1-mF low-ESR capacitor (3)
should be connected between this terminal and DVSS_CORE. This terminal
must not be used to power external devices.
VR_PWM
48
P
Voltage reference for 1.8-V digital PWM core supply. A pinout of the internally
regulated 1.8-V power used by digital PWM core logic. A 0.1-mF low-ESR
capacitor (3) should be connected between this terminal and DVSS_PWM. This
terminal must not be used to power external devices.
VRA_PLL
1
P
Voltage reference for 1.8-V PLL analog supply. A pinout of the internally
regulated 1.8-V power used by PLL logic. A 0.1-mF low-ESR capacitor (3) should
be connected between this terminal and AVSS_PLL. This terminal must not be
used to power external devices.
VRD_PLL
7
P
Voltage reference for 1.8-V PLL digital supply. A pinout of the internally
regulated 1.8-V power used by PLL logic. A 0.1-mF low-ESR capacitor (3) should
be connected between this terminal and AVSS_PLL. This terminal must not be
used to power external devices.
XTL_IN
20
AI
XTL_OUT and XTL_IN are the only LVCMOS terminals on the device. They
provide a reference clock for the TAS5508C via use of an external
fundamental-mode crystal. XTL_IN is the 1.8-V input port for the oscillator
circuit. A 13.5-MHz crystal (HCM49) is recommended.
XTL_OUT
19
AO
XTL_OUT and XTL_IN are the only LVCMOS terminals on the device. They
provide a reference clock for the TAS5508C via use of an external
fundamental-mode crystal. XTL_OUT is the 1.8-V output drive to the crystal. A
13.5-MHz crystal (HCM49) is recommended.
(3)
2.2
Pullup
System reset input, active-low. A system reset is generated by applying a logic
low to this terminal. RESET is an asynchronous control signal that restores the
TAS5508C to its default conditions, sets the valid output low, and places the
PWM in the hard mute (M) state. Master volume is immediately set to full
attenuation. On the release of RESET, if PDN is high, the system performs a 4to 5-ms device initialization and sets the volume at mute.
Output indicating validity of PWM outputs, active-high
If desired, low-ESR capacitance values can be implemented by paralleling two or more ceramic capacitors of equal value. Paralleling
capacitors of equal value provides an extended high-frequency supply decoupling. This approach avoids the potential of producing
parallel resonance circuits that have been observed when paralleling capacitors of different values.
TAS5508C Functional Description
Figure 2-1 shows the TAS5508C functional structure. The following sections describe the TAS5508C
functional blocks:
• Power supply
Description
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
17
TAS5508C
SLES257 – SEPTEMBER 2010
•
•
•
•
2.2.1
www.ti.com
Clock, PLL, and serial data interface
I2C serial-control interface
Device control
Digital audio processor (DAP)
Power Supply
The power-supply section contains supply regulators that provide analog and digital regulated power for
various sections of the TAS5508C. The analog supply supports the analog PLL, whereas digital supplies
support the digital PLL, the digital audio processor (DAP), the pulse-width modulator (PWM), and the
output control (reclocker). The regulators can also be turned off when terminals RESET and PDN are both
low.
2.2.2
Clock, PLL, and Serial Data Interface
The TAS5508C is a clocked slave-only device that requires the use of an external 13.5-MHz crystal. It
accepts MCLK, SCLK, and LRCLK as inputs only.
The TAS5508C uses the external crystal to provide a time base for:
• Continuous data and clock error detection and management
• Automatic data-rate detection and configuration
• Automatic MCLK-rate detection and configuration (automatic bank switching)
• Supporting I2C operation/communication while MCLK is absent
The TAS5508C automatically handles clock errors, data-rate changes, and master-clock frequency
changes without requiring intervention from an external system controller. This feature significantly
reduces system complexity and design.
2.2.2.1
Serial Audio Interface
The TAS5508C operates as a slave-only/receive-only serial data interface in all modes. The TAS5508C
has four PCM serial data interfaces to permit eight channels of digital data to be received though the
SDIN1, SDIN2, SDIN3, and SDIN4 inputs. The serial audio data is in MSB-first, 2s-complement format.
The serial data input interface of the TAS5508C can be configured in right-justified, I2S, or left-justified
modes. The serial data interface format is specified using the I2C data-interface control register. The
supported formats and word lengths are shown in Table 2-1.
18
Description
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
Table 2-1. Serial Data Formats
RECEIVE SERIAL DATA FORMAT
WORD LENGTH
Right-justified
16
Right-justified
20
Right-justified
24
I2S
16
2
I S
20
I2S
24
Left-justified
16
Left-justified
20
Left-justified
24
Serial data is input on SDIN1, SDIN2, SDIN3, and SDIN4. The TAS5508C accepts 16-, 20-, or 24-bit
serial data at 32, 38, 44.1, 48, 88.2, 96, 176.4, or 192 kHz in left-justified, I2S, or right-justified format.
Data is input using a 64-Fs SCLK clock and an MCLK rate of 128, 192, 256, 384, 512, or 768 Fs, up to a
maximum of 50 MHz. The clock speed and serial data format are I2C configurable.
I 2C Serial-Control Interface
2.2.3
The TAS5508C has an I2C serial-control slave interface (address 0x36) to receive commands from a
system controller. The serial-control interface supports both normal-speed (100 kHz) and high-speed (400
kHz) operations without wait states. Because the TAS5508C has a crystal time base, this interface
operates even when MCLK is absent.
The serial control interface supports both single-byte and multiple-byte read/write operations for status
registers and the general control registers associated with the PWM. However, for the DAP
data-processing registers, the serial control interface also supports multiple-byte (4-byte) write operations.
The I2C supports a special mode which permits I2C write operations to be broken up into multiple
data-write operations that are multiples of 4 data bytes. These are 6-byte, 10-byte, 14-byte, 18-byte, etc.,
write operations that are composed of a device address, read/write bit, subaddress, and any multiple of 4
bytes of data. This permits the system to incrementally write large register values without blocking other
I2C transactions. In order to use this feature, the first block of data is written to the target I2C address, and
each subsequent block of data is written to a special append register (0xFE) until all the data is written
and a stop bit is sent. An incremental read operation is not supported.
2.2.4
Device Control
The TAS5508C control section provides the control and sequencing for the TAS5508C. The device control
provides both high- and low-level control for the serial control interface, clock and serial data interfaces,
digital audio processor, and pulse-width modulator sections.
2.2.5
Digital Audio Processor (DAP)
The DAP arithmetic unit is used to implement all audio-processing functions: soft volume, loudness
compensation, bass and treble processing, dynamic range control, channel filtering, input and output
mixing. Figure 2-3 shows the TAS5508C DAP architecture.
The DAP accepts 24-bit data from the serial data interface and outputs 32-bit data to the PWM section.
The DAP supports two configurations, one for 32-kHz to 96-kHz data and one for 176.4-kHz to 192-kHz
data.
2.2.5.1
TAS5508C Audio-Processing Configurations
The 32-kHz to 96-kHz configuration supports eight channels of data processing that can be configured
either as eight channels, or as six channels with two channels for separate stereo line outputs.
Description
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
19
TAS5508C
SLES257 – SEPTEMBER 2010
www.ti.com
The 176.4-kHz to 192-kHz configuration supports three channels of signal processing with five channels
passed though (or derived from the three processed channels).
To support efficiently the processing requirements of both multichannel 32-kHz to 96-kHz data and the
2-channel 176.4-kHz and 192-kHz data, the TAS5508C has separate audio-processing features for
32-kHz to 96-kHz data rates and for 176.4 kHz and 192 kHz. See Table 2-2 for a summary of TAS5508C
processing feature sets.
2.2.5.2
TAS5508C Audio Signal-Processing Functions
The DAP provides 10 primary signal-processing functions:
1. The data-processing input has a full 8×8 input crossbar mixer. This enables each input to be any ratio
of the eight input channels.
2. Two I2C programmable threshold detectors in each channel support automute.
3. Seven biquads per channel
4. Four soft bass and treble tone controls with ±18-dB range, programmable corner frequencies, and
second-order slopes. In 8-channel mode, bass and treble controls are normally configured as follows:
– Bass and treble 1: Channel 1 (left), channel 2 (right), and channel 7 (center)
– Bass and treble 2: Channel 3 (left surround) and channel 4 (right surround)
– Bass and treble 3: Channel 5 (left back surround) and channel 6 (right back surround)
– Bass and treble 4: Channel 8 (subwoofer)
5. Individual channel and master volume controls. Each control provides an adjustment range of 18 dB to
–127 dB. This permits a total volume device control range of 36 dB to –127 dB plus mute. The master
volume control can be configured to control six or eight channels. The DAP soft volume and mute
update interval is I2C programmable. The update is performed at a fixed rate regardless of the sample
rate.
6. Programmable loudness compensation that is controlled via the combination of the master and
individual volume settings.
7. Two dual-threshold dual-rate dynamic range compressors (DRCs). The volume gain values provided
are used as input parameters using the maximum RMS (master volume × individual channel volume).
8. 8×2 output mixer (channels 1–6). Each output can be any ratio of any two signal-processed channels.
9. 8×3 output mixer (channels 7 and 8). Each output can be any ratio of any three signal-processed
channels.
10. The DAP maintains three sets of coefficient banks that are used to maintain separate sets of
sample-rate-dependent parameters for the biquad, tone controls, loudness, and DRC in RAM. These
can be set to be automatically selected for one or more data sample rates or can be manually selected
under I2C program control. This feature enables coefficients for different sample rates to be stored in
the TAS5508C and then selected when needed.
20
Description
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
Table 2-2. TAS5508C Audio Processing Feature Sets
FEATURE
32 kHz–96 kHz
8-CHANNEL FEATURE SET
Signal-processing channels
8
Pass-through channels
Master volume
176.4- and 192-kHz
FEATURE SET
6+2
3
1 for 6 channels
1 for 3 channels
N/A
1 for 8 channels
Individual channel volume
controls
Bass and treble tone
controls
32 kHz–96 kHz
6 + 2 LINEOUT FEATURE SET
5
8
Four bass and treble tone controls
with ±18-dB range, programmable
corner frequencies, and secondorder slopes
L, R, and C (Ch1, 2, and 7)
LS, RS (Ch3 and 4)
LBS, RBS (Ch5 and 6)
Sub (Ch8)
Biquads
3
Four bass and treble tone controls
with ±18-dB range, programmable
corner frequencies, and secondorder slopes
L, R, and C (Ch1, 2, and 7)
LS, RS (Ch3 and 4)
Sub (Ch8)
Line L and R (Ch5 and 6)
Two bass and treble tone
controls with ±18-dB range,
programmable corner
frequencies, and second-order
slopes
L and R (Ch1 and 2)
Sub (Ch8)
56
21
Dynamic range
compressors
DRC1 for seven satellites and
DRC2 for sub
Input/output mapping/
mixing
Each of the three signalprocessing channels or the five
pass-though channel inputs can
Each of the eight signal-processing channel inputs can be any ratio of the be any ratio of the eight input
eight input channels.
channels.
Each of the eight outputs can be any ratio of any two processed channels. Each of the eight outputs can be
any ratio of any of the three
processed channels or five
bypass channels.
DC-blocking filters
(implemented in PWM
section)
Eight channels
Digital de-emphasis
(implemented in PWM
section)
Loudness
Eight channels for 32 kHz,
44.1 kHz, and 48 kHz
Eight channels
Number of coefficient sets
stored
2.3
2.3.1
DRC1 for five satellites and DRC2
for sub (Ch5 and 6 uncompressed)
DRC1 for two satellites and
DRC2 for sub
Six channels for 32 kHz, 44.1 kHz,
and 48 kHz
Six channels
N/A
Three channels
Three additional coefficient sets can be stored in memory.
TAS5508C DAP Architecture
TAS5508C DAP Architecture Diagrams
Figure 2-1 shows the TAS5508C DAP architecture for Fs = 96 kHz. Note the TAS5508C bass
management architecture shown in channels 1, 2, 7, and 8. Note that the I2C registers are shown to help
the designer configure the TAS5508C.
Figure 2-2 shows the TAS5508C architecture for Fs = 176.4 kHz or Fs = 192 kHz. Note that only channels
1, 2, and 8 contain all the features. Channels 3–7 are pass-through except for master volume control.
Figure 2-3 shows TAS5508C detailed channel processing. The output mixer is 8×2 for channels 1–6 and
8×3 for channels 7 and 8.
Description
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
21
TAS5508C
SLES257 – SEPTEMBER 2010
www.ti.com
Master Vol
(0xD9)
SDIN1-L (L) (1)
SDIN1-R (R)
SDIN2-L (LS)
SDIN2-R (RS)
SDIN3-L (LBS)
SDIN3-R (RBS)
SDIN4-L (C)
SDIN4-R (LFE)
A
B
C
D
E
F
G
H
SDIN1-L (L)
SDIN1-R (R) (1)
SDIN2-L (LS)
SDIN2-R (RS)
SDIN3-L (LBS)
SDIN3-R (RBS)
SDIN4-L (C)
SDIN4-R (LFE)
A
B
C
D
E
F
G
H
SDIN1-L (L)
SDIN1-R (R)
SDIN2-L (LS) (1)
SDIN2-R (RS)
SDIN3-L (LBS)
SDIN3-R (RBS)
SDIN4-L (C)
SDIN4-R (LFE)
A
B
C
D
E
F
G
H
SDIN1-L (L)
SDIN1-R (R)
SDIN2-L (LS)
SDIN2-R (RS) (1)
SDIN3-L (LBS)
SDIN3-R (RBS)
SDIN4-L (C)
SDIN4-R (LFE)
A
B
C
D
E
F
G
H
SDIN1-L (L)
SDIN1-R (R)
SDIN2-L (LS)
SDIN2-R (RS)
SDIN3-L (LBS) (1)
SDIN3-R (RBS)
SDIN4-L (C)
SDIN4-R (LFE)
A
B
C
D
E
F
G
H
SDIN1-L (L)
SDIN1-R (R)
SDIN2-L (LS)
SDIN2-R (RS)
SDIN3-L (LBS)
SDIN3-R (RBS) (1)
SDIN4-L (C)
SDIN4-R (LFE)
A
B
C
D
E
F
G
H
SDIN1-L (L)
SDIN1-R (R)
SDIN2-L (LS)
SDIN2-R (RS)
SDIN3-L (LBS)
SDIN3-R (RBS)
SDIN4-L (C) (1)
SDIN4-R (LFE)
A
B
C
D
E
F
G
H
IP Mixer 1
(I2C 0x41)
8×8
Crossbar
Input Mixer
7 DAP 1
BQ
(0x51−
0x57)
Bass and
Treble 1
(0xDA−
0xDD)
DAP 1
Volume
(0xD1)
Master Vol
(0xD9)
IP Mixer 2
(I2C 0x42)
8×8
Crossbar
Input Mixer
7 DAP 2
BQ
(0x58−
0x5E)
Bass and
Treble 1
(0xDA−
0xDD)
DAP 2
Volume
(0xD2)
Master Vol
(0xD9)
IP Mixer 3
(I2C 0x43)
8×8
Crossbar
Input Mixer
7 DAP 3
BQ
(0x5F−
0x65)
Bass and
Treble 2
(0xDA−
0xDD)
DAP 3
Volume
(0xD3)
Master Vol
(0xD9)
IP Mixer 4
(I2C 0x44)
8×8
Crossbar
Input Mixer
7 DAP 4
BQ
(0x66−
0x6C)
Bass and
Treble 2
(0xDA−
0xDD)
DAP 4
Volume
(0xD4)
Master Vol
(0xD9)
IP Mixer 5
(I2C 0x45)
8×8
Crossbar
Input Mixer
7 DAP 5
BQ
(0x6D−
0x73)
Bass and
Treble 3
(0xDA−
0xDD)
DAP 5
Volume
(0xD5)
Master Vol
(0xD9)
IP Mixer 6
(I2C 0x46)
8×8
Crossbar
Input Mixer
7 DAP 6
BQ
(0x74−
0x7A)
Coeff = 0 (lin), (I2C 0x4E)
Bass and
Treble 3
(0xDA−
0xDD)
Master Vol
(0xD9)
Coeff = 0 (lin), (I2C 0x4B)
IP Mixer 7
(I2C 0x47)
8×8
Crossbar
Input Mixer
2 DAP 7
BQ
(0x7B−
0x7C)
Coeff = 1 (lin)
(I2C 0x4D)
DAP 6
Volume
(0xD6)
5 DAP 7
BQ
(0x7D−
0x81)
Bass and
Treble 1
(0xDA−
0xDD)
DAP 7
Volume
(0xD7)
Max Vol
Loudness
(0x91−
0x95)
DRC1
(0x96−
0x9C)
OP Mixer 1
(I2C 0xAA)
8 × 2 Output
Mixer
L to
PWM1
DRC1
(0x96−
0x9C)
OP Mixer 2
(I2C 0xAB)
8 × 2 Output
Mixer
R to
PWM2
DRC1
(0x96−
0x9C)
OP Mixer 3
(I2C 0xAC)
8 × 2 Output
Mixer
LS to
PWM3
DRC1
(0x96−
0x9C)
OP Mixer 4
(I2C 0xAD)
8 × 2 Output
Mixer
RS to
PWM4
DRC1
(0x96−
0x9C)
OP Mixer 5
(I2C 0xAE)
8 × 2 Output
Mixer
LBS to
PWM5
DRC1
(0x96−
0x9C)
OP Mixer 6
(I2C 0xAF)
8 × 2 Output
Mixer
RBS to
PWM6
DRC1
(0x96−
0x9C)
OP Mixer 7
(I2C 0xB0)
8 × 3 Output
Mixer
C to
PWM7
DRC2
(0x9D−
0xA1)
OP Mixer 8
(I2C 0xB1)
8 × 3 Output
Mixer
Sub to
PWM8
Max Vol
Loudness
(0x91−
0x95)
Max Vol
Loudness
(0x91−
0x95)
Max Vol
Loudness
(0x91−
0x95)
Max Vol
Loudness
(0x91−
0x95)
Max Vol
Loudness
(0x91−
0x95)
Max Vol
Loudness
(0x91−
0x95)
Coeff = 0 (lin), (I2C 0x4C)
Coeff = 0 (lin), (I2C 0x49)
SDIN1-L (L)
SDIN1-R (R)
SDIN2-L (LS)
SDIN2-R (RS)
SDIN3-L (LBS)
SDIN3-R (RBS)
SDIN4-L (C)
SDIN4-R (LFE) (1)
A
B
C
D
E
F
G
H
IP Mixer 8
(I2C 0x48)
8×8
Crossbar
Input Mixer
2 DAP 8
BQ
(0x82−
0x83)
Coeff = 1 (lin)
(I2C 0x50)
Master Vol
(0xD9)
Coeff = 0 (lin)
(I2C 0x4A)
5 DAP 8
BQ
(0x84−
0x88)
Bass and
Treble 4
(0xDA−
0xDD)
DAP 8
Volume
(0xD8)
Max Vol
Loudness
(0x91−
0x95)
Coeff = 0 (lin), (I2C 0x4F)
(1)
B0014-01
Default inputs
Figure 2-1. TAS5508C DAP Architecture With I2C Registers (Fs ≤ 96 kHz)
22
Description
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
Master Vol
(0xD9)
(1)
SDIN1-L (L)
SDIN1-R (R)
SDIN2-L (LS)
SDIN2-R (RS)
SDIN3-L (LBS)
SDIN3-R (RBS)
SDIN4-L (C)
SDIN4-R (LFE)
SDIN1-L (L)
(1)
SDIN1-R (R)
SDIN2-L (LS)
SDIN2-R (RS)
SDIN3-L (LBS)
SDIN3-R (RBS)
SDIN4-L (C)
SDIN4-R (LFE)
SDIN1-L (L)
SDIN1-R (R)
(1)
SDIN2-L (LS)
SDIN2-R (RS)
SDIN3-L (LBS)
SDIN3-R (RBS)
SDIN4-L (C)
SDIN4-R (LFE)
SDIN1-L (L)
SDIN1-R (R)
SDIN2-L (LS)
(1)
SDIN2-R (RS)
SDIN3-L (LBS)
SDIN3-R (RBS)
SDIN4-L (C)
SDIN4-R (LFE)
SDIN1-L (L)
SDIN1-R (R)
SDIN2-L (LS)
SDIN2-R (RS)
(1)
SDIN3-L (LBS)
SDIN3-R (RBS)
SDIN4-L (C)
SDIN4-R (LFE)
SDIN1-L (L)
SDIN1-R (R)
SDIN2-L (LS)
SDIN2-R (RS)
SDIN3-L (LBS)
(1)
SDIN3-R (RBS)
SDIN4-L (C)
SDIN4-R (LFE)
SDIN1-L (L)
SDIN1-R (R)
SDIN2-L (LS)
SDIN2-R (RS)
SDIN3-L (LBS)
SDIN3-R (RBS)
(1)
SDIN4-L (C)
SDIN4-R (LFE)
SDIN1-L (L)
SDIN1-R (R)
SDIN2-L (LS)
SDIN2-R (RS)
SDIN3-L (LBS)
SDIN3-R (RBS)
SDIN4-L (C)
(1)
SDIN4-R (LFE)
A
B
C
D
E
F
G
H
A
B
C
D
E
F
G
H
A
B
C
D
E
F
G
H
A
B
C
D
E
F
G
H
A
B
C
D
E
F
G
H
A
B
C
D
E
F
G
H
A
B
C
D
E
F
G
H
A
B
C
D
E
F
G
H
IP Mixer 1
2
(I C 0x41)
8´8
Crossbar
Input Mixer
4BQ
(0x51–
0x54)
Bass and
Treble 1
(0xDA–
0xDD)
DAP 1
Volume
(0xD1)
Master Vol
(0xD9)
IP Mixer 2
2
(I C 0x42)
8´8
Crossbar
Input Mixer
4BQ
(0x58–
0x5B)
Bass and
Treble 1
(0xDA–
0xDD)
DAP 2
Volume
(0xD2)
Max Vol
Loudness
(0x91–
0x95)
DRC1
(0x96–
0x9C)
OP Mixer 1
2
(I C 0xAA)
8´2
Output Mixer
L to
PWM1
Max Vol
Loudness
(0x91–
0x95)
DRC1
(0x96–
0x9C)
OP Mixer 2
2
(I C 0xAB)
8´2
Output Mixer
R to
PWM2
Master Vol
(0xD9)
IP Mixer 3
2
(I C 0x43)
8´8
Crossbar
Input Mixer
DAP 3
Volume
(0xD3)
3BQ
(0x5F–
0x61)
DRC1
(0x96–
0x9C)
OP Mixer 3
2
(I C 0xAC)
8´2
Output Mixer
LS to
PWM3
Master Vol
(0xD9)
IP Mixer 4
2
(I C 0x44)
8´8
Crossbar
Input Mixer
DAP 4
Volume
(0xD4)
3BQ
(0x66–
0x68)
DRC1
(0x96–
0x9C)
OP Mixer 4
2
(I C 0xAD)
8´2
Output Mixer
RS to
PWM4
Master Vol
(0xD9)
IP Mixer 5
2
OP Mixer 5
DAP 5
Volume
(0xD5)
(I C 0x45)
8´8
Crossbar
Input Mixer
2
(I C 0xAE)
8´2
Output Mixer
LBS to
PWM5
Master Vol
(0xD9)
IP Mixer 6
2
OP Mixer 6
DAP 6
Volume
(0xD6)
(I C 0x46)
8´8
Crossbar
Input Mixer
2
(I C 0xAF)
8´2
Output Mixer
RBS to
PWM6
Master Vol
(0xD9)
IP Mixer 7
2
(I C 0x47)
8´8
Crossbar
Input Mixer
DAP 7
Volume
(0xD7)
3BQ
(0x7B–
0x7D)
Master Vol
(0xD9)
IP Mixer 8
2
(I C 0x48)
8´8
Crossbar
Input Mixer
4BQ
(0x82–
0x85)
Bass and
Treble 4
(0xDA–
0xDD)
DAP 8
Volume
(0xD8)
DRC1
(0x96–
0x9C)
OP Mixer 7
2
(I C 0xB0)
8´3
Output Mixer
C to
PWM7
Max Vol
Loudness
(0x91–
0x95)
DRC2
(0x9D–
0xA1)
OP Mixer 8
2
(I C 0xB1)
8´3
Output Mixer
Sub to
PWM8
B0015-03
(1)
Default inputs
Figure 2-2. TAS5508C Architecture With I2C Registers (Fs = 176.4 kHz or Fs = 192 kHz)
Description
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
23
TAS5508C
SLES257 – SEPTEMBER 2010
www.ti.com
A_to_ipmix
Left
Master
Volume
A
B
SDIN1
Right
B_to_ipmix
Channel Volume
C_to_ipmix
Left
C
D
SDIN2
Right
E_to_ipmix
E
SDIN3
7
Biquads
in
Series
Input
Mixer
Bass
and
Treble
Inline
F_to_ipmix
Output
Gain
Output Mixer Sums
Any Two Channels
Bass
and
Treble
F
Right
DRC
Bypass
Loudness
D_to_ipmix
Left
Max
Volume
Bass and Treble
Bypass
PrePostVolume Volume
DRC
32-Bit
Trunc
DRC
Inline
PWM
Proc
PWM
Output
1 Other
Channel Output
From 7 Available
G_to_ipmix
Left
G
SDIN4
H
Right
H_to_ipmix
B0016-01
Figure 2-3. TAS5508C Detailed Channel Processing
I 2C Coefficient Number Formats
2.3.2
The architecture of the TAS5508C is contained in ROM resources within the TAS5508C and cannot be
altered. However, mixer gain, level offset, and filter tap coefficients, which can be entered via the I2C bus
interface, provide a user with the flexibility to set the TAS5508C to a configuration that achieves
system-level goals.
The firmware is executed in a 48-bit, signed, fixed-point arithmetic machine. The most significant bit of the
48-bit data path is a sign bit, and the 47 lower bits are data bits. Mixer gain operations are implemented
by multiplying a 48-bit, signed data value by a 28-bit, signed gain coefficient. The 76-bit, signed output
product is then truncated to a signed, 48-bit number. Level offset operations are implemented by adding a
48-bit, signed offset coefficient to a 48-bit, signed data value. In most cases, if the addition results in
overflowing the 48-bit, signed number format, saturation logic is used. This means that if the summation
results in a positive number that is greater than 0x7FFF FFFF FFFF (the spaces are used to ease the
reading of the hexadecimal number), the number is set to 0x7FFF FFFF FFFF. If the summation results in
a negative number that is less than 0x8000 0000 0000, the number is set to 0x8000 0000 0000.
2.3.2.1
28-Bit 5.23 Number Format
All mixer gain coefficients are 28-bit coefficients using a 5.23 number format. Numbers formatted as 5.23
numbers have 5 bits to the left of the binary point and 23 bits to the right of the binary point. This is shown
in Figure 2-4.
24
Description
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
2−23 Bit
2−4 Bit
2−1 Bit
20 Bit
23 Bit
Sign Bit
S_xxxx.xxxx_xxxx_xxxx_xxxx_xxxx_xxx
M0007-01
Figure 2-4. 5.23 Format
The decimal value of a 5.23 format number can be found by following the weighting shown in Figure 2-5. If
the most significant bit is logic 0, the number is a positive number, and the weighting shown yields the
correct number. If the most significant bit is a logic 1, then the number is a negative number. In this case,
every bit must be inverted, a 1 added to the result, and then the weighting shown in Figure 2-5 applied to
obtain the magnitude of the negative number.
23 Bit
22 Bit
20 Bit
2−1 Bit
2−4 Bit
2−23 Bit
(1 or 0) y 23 + (1 or 0) y 22 + … + (1 or 0) y 20 + (1 or 0) y 2−1 + … + (1 or 0) y 2−4 + … + (1 or 0) y 2−23
M0008-01
Figure 2-5. Conversion Weighting Factors—5.23 Format to Floating Point
Gain coefficients, entered via the I2C bus, must be entered as 32-bit binary numbers. The format of the
32-bit number (4-byte or 8-digit hexadecimal number) is shown in Figure 2-6.
Fraction
Digit 6
Sign
Bit
Integer
Digit 1
u
u
u
u
Coefficient
Digit 8
S
x
x
x
Coefficient
Digit 7
Fraction
Digit 1
x. x
x
x
Coefficient
Digit 6
Fraction
Digit 2
x
x
x
x
Coefficient
Digit 5
Fraction
Digit 3
x
x
x
x
Coefficient
Digit 4
Fraction
Digit 4
x
x
x
Fraction
Digit 5
x
x
Coefficient
Digit 3
x
x
x
Coefficient
Digit 2
0
x
x
x
x
Coefficient
Digit 1
u = unused or don’t care bits
Digit = hexadecimal digit
M0009-01
2
Figure 2-6. Alignment of 5.23 Coefficient in 32-Bit I C Word
As Figure 2-6 shows, the hexadecimal (hex) value of the integer part of the gain coefficient cannot be
Description
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
25
TAS5508C
SLES257 – SEPTEMBER 2010
www.ti.com
concatenated with the hex value of the fractional part of the gain coefficient to form the 32-bit I2C
coefficient. The reason is that the 28-bit coefficient contains 5 bits of integer, and thus the integer part of
the coefficient occupies all of one hex digit and the most significant bit of the second hex digit. In the same
way, the fractional part occupies the lower three bits of the second hex digit, and then occupies the other
five hex digits (with the eighth digit being the zero-valued most significant hex digit).
2.3.2.2
48-Bit 25.23 Number Format
All level adjustment and threshold coefficients are 48-bit coefficients using a 25.23 number format.
Numbers formatted as 25.23 numbers have 25 bits to the left of the decimal point and 23 bits to the right
of the decimal point. This is shown in Figure 2-7.
2−23 Bit
2−10 Bit
2−1 Bit
20 Bit
216 Bit
222 Bit
223 Bit
Sign Bit
S_xxxx_xxxx_xxxx_xxxx_xxxx_xxxx.xxxx_xxxx_xxxx_xxxx_xxxx_xxx
M0007-02
Figure 2-7. 25.23 Format
Figure 2-8 shows the derivation of the decimal value of a 48-bit 25.23 format number.
223 Bit
222 Bit
20 Bit
2−1 Bit
2−23 Bit
(1 or 0) y 223 + (1 or 0) y 222 + … + (1 or 0) y 20 + (1 or 0) y 2−1 + … + (1 or 0) y 2−23
M0008-02
2
Figure 2-8. Alignment of 5.23 Coefficient in 32-Bit I C Word
Two 32-bit words must be sent over the I2C bus to download a level or threshold coefficient into the
TAS5508C. The alignment of the 48-bit, 25.23 formatted coefficient in the 8-byte (two 32-bit words) I2C
word is shown in Figure 2-9.
26
Description
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
Integer
Digit 4
(Bits 211 − 29)
Sign
Bit
Integer
Digit 1
u
u
u
u
Coefficient
Digit 16
u
u
u
u
Coefficient
Digit 15
u
u
u
u
Coefficient
Digit 14
u
u
u
u
Coefficient
Digit 13
S
x
x
x
Coefficient
Digit 12
Integer
Digit 2
x
x
x
x
Coefficient
Digit 11
Integer
Digit 3
x
x
x
x
Coefficient
Digit 10
x
Word 1
(MostSignificant
Word)
x
Fraction
Digit 6
Integer
Digit 5
x
x
Coefficient
Digit 9
Integer
Digit 4
(Bit 28)
x
x
x
x
Coefficient
Digit 8
Integer
Digit 6
x
x
x
x
Coefficient
Digit 7
Fraction
Digit 1
x. x
x
x
Coefficient
Digit 6
Fraction
Digit 2
x
x
x
x
Coefficient
Digit 5
Fraction
Digit 3
x
x
x
x
Coefficient
Digit 4
Fraction
Digit 4
x
x
x
x
Coefficient
Digit 3
Fraction
Digit 5
x
x
x
x
Coefficient
Digit 2
0
x
x
x
x
Word 2
(LeastSignificant
Word)
Coefficient
Digit 1
u = unused or don’t care bits
Digit = hexadecimal digit
M0009-02
Figure 2-9. Alignment of 25.23 Coefficient in Two 32-Bit I2C Words
2.3.2.3
TAS5508C Audio Processing
The TAS5508C digital audio processing is designed so that noise produced by filter operations is
maintained below the smallest signal amplitude of interest, as shown in Figure 2-10. The TAS5508C
achieves this low noise level by increasing the precision of the signal representation substantially above
the number of bits that are absolutely necessary to represent the input signal.
Similarly, the TAS5508C carries additional precision in the form of overflow bits to permit the value of
intermediate calculations to exceed the input precision without clipping. The TAS5508C advanced digital
audio processor achieves both of these important performance capabilities by using a high-performance
digital audio processing architecture with a 48-bit data path, 28-bit filter coefficients, and a 76-bit
accumulator.
Description
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
27
TAS5508C
SLES257 – SEPTEMBER 2010
www.ti.com
Ideal Input
Possible Outputs
Desired Output
Values Retained by
Overflow Bits
Overflow
Maximum Signal Amplitude
Filter
Operation
Signal
Bits
Input
Reduced
SNR
Signal
Output
Signal
Bits
Output
Noise Floor With No
Additional Precision
Noise Floor as a Result
of Additional Precision
M0010-01
Figure 2-10. TAS5508C Digital Audio Processing
2.4
Input Crossbar Mixer
The TAS5508C has a full 8×8 input crossbar mixer. This mixer permits each signal processing channel
input to be any ratio of any of the eight input channels, as shown in Figure 2-11. The control parameters
for the input crossbar mixer are programmable via the I2C interface. See the Input Mixer Registers
(0x41–0x48, Channels 1–8), Section 7.16, for more information.
Gain Coefficient
28
48
SDIN1-L
Gain Coefficient
48
28
48
48
SUM
SDIN1-R
w
w
w
Gain Coefficient
48
28
48
SDIN4-R
M0011-01
Figure 2-11. Input Crossbar Mixer
2.5
Biquad Filters
For 32-kHz to 96-kHz data, the TAS5508C provides 56 biquads across the eight channels (seven per
channel).
For 176.4-kHz and 192-kHz data, the TAS5508C has 21 biquads across the three channels (seven per
channel). All of the biquad filters are second-order direct form I structure.
28
Description
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
The direct form I structure provides a separate delay element and mixer (gain coefficient) for each node in
the biquad filter. Each mixer output is a signed 76-bit product of a signed 48-bit data sample (25.23 format
number) and a signed 28-bit coefficient (5.23 format number), as shown in Figure 2-12. The 76-bit ALU in
the TAS5508C allows the 76-bit resolution to be retained when summing the mixer outputs (filter
products).
The five 28-bit coefficients for the each of the 56 biquads are programmable via the I2C interface. See
Table 2-3.
b0
28
48
76
76
b1
z
–1
a1
28
48
76
–1
76
–1
48
a2
28
48
z
28
b2
z
48
Magnitude
Truncation
S
z
28
76
76
–1
48
M0012-01
Figure 2-12. Biquad Filter Structure
All five coefficients for one biquad filter structure are written to one I2C register containing 20 bytes (or five
32-bit words). The structure is the same for all biquads in the TAS5508C. Registers 0x51–0x88 show all
the biquads in the TAS5508C. Note that u[31:28] bits are unused and default to 0x0.
Table 2-3. Contents of One 20-Byte Biquad Filter Register (Default = All-Pass)
2.6
INITIALIZATION GAIN COEFFICIENT VALUE
DESCRIPTION
REGISTER FIELD CONTENTS
DECIMAL
HEX
b0 coefficient
u[31:28], b0[27:24], b0[23:16], b0[15:8], b0[7:0]
1.0
0x00, 0x80, 0x00, 0x00
b1 coefficient
u[31:28], b1[27:24], b1[23:16], b1[15:8], b1[7:0]
0.0
0x00, 0x00, 0x00, 0x00
b2 coefficient
u[31:28], b2[27:24], b2[23:16], b2[15:8], b2[7:0]
0.0
0x00, 0x00, 0x00, 0x00
a1 coefficient
u[31:28], a1[27:24], a1[23:16], a1[15:8], a1[7:0]
0.0
0x00, 0x00, 0x00, 0x00
a2 coefficient
u[31:28], a2[27:24], a2[23:16], a2[15:8], a2[7:0]
0.0
0x00, 0x00, 0x00, 0x00
Bass and Treble Controls
From 32-kHz to 96-kHz data, the TAS5508C has four bass and treble tone controls. Each control has a
±18-dB control range with selectable corner frequencies and second-order slopes. These controls operate
four channel groups:
• L, R, and C (channels 1, 2, and 7)
• LS, RS (channels 3 and 4)
• LBS, RBS (alternatively called L and R lineout) (channels 5 and 6)
• Sub (channel 8)
For 176.4-kHz and 192-kHz data, the TAS5508C has two bass and treble tone controls. Each control has
a ±18-dB I2C control range with selectable corner frequencies and second-order slopes. These controls
operate two channel groups:
Description
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
29
TAS5508C
SLES257 – SEPTEMBER 2010
•
•
www.ti.com
L and R
Sub
The bass and treble filters use a soft update rate that does not produce artifacts during adjustment.
Table 2-4. Bass and Treble Filter Selections
3-dB CORNER FREQUENCIES
FS
(kHz)
FILTER SET 1
FILTER SET 2
FILTER SET 3
FILTER SET 4
FILTER SET 5
BASS
TREBLE
BASS
TREBLE
BASS
TREBLE
BASS
TREBLE
BASS
TREBLE
32
42
917
83
1833
125
3000
146
3667
167
4333
38
49
1088
99
2177
148
3562
173
4354
198
5146
44.1
57
1263
115
2527
172
4134
201
5053
230
5972
48
63
1375
125
2750
188
4500
219
5500
250
6500
88.2
115
2527
230
5053
345
8269
402
10106
459
11944
96
125
2750
250
5500
375
9000
438
11000
500
13000
176.4
230
5053
459
10106
689
16538
804
20213
919
23888
192
250
5500
500
11000
750
18000
875
22000
1000
26000
The I2C registers that control bass and treble are:
• Bass and treble bypass register (0x89–0x90, channels 1–8)
• Bass and treble slew rates (0xD0)
• Bass filter sets 1–5 (0xDA)
• Bass filter index (0xDB)
• Treble filter sets 1–5 (0xDC)
• Treble filter index (0xDD)
2.7
Volume, Automute, and Mute
The TAS5508C provides individual channel and master volume controls. Each control provides an
adjustment range of 18 dB to –100 dB in 0.25-dB increments. This permits a total volume device control
range of 36 dB to –100 dB plus mute. The master volume control can be configured to control six or eight
channels.
The TAS5508C has a master soft mute control that can be enabled by a terminal or I2C command. The
device also has individual channel soft mute controls that are enabled via I2C.
The soft volume and mute update rates are programmable. The soft adjustments are performed using a
soft-gain linear update with an I2C-programmable linear step size at a fixed temporal rate. The linear
soft-gain step size can be varied from 0.5 to 0.003906. Table 2-5 lists the linear gain step sizes.
Table 2-5. Linear Gain Step Size
STEP SIZE (GAIN)
0.5
0.25
0.125
0.0625
0.03125
0.015625
0.007813
0.003906
Time to go from 36.124 db to –127 dB in ms
10.67
21.33
42.67
85.34
170.67
340.35
682.70
1365.4
Time to go from 18.062 db to –127 dB in ms
1.33
2.67
5.33
10.67
21.33
42.67
85.33
170.67
Time to go from 0 db to –127 dB in ms
0.17
0.33
0.67
1.33
2.67
5.33
10.67
21.33
2.8
Automute and Mute
The TAS5508C has individual channel automute controls that are enabled via the I2C interface. Two
separate detectors can trigger the automute:
• Input automute: All channels are muted when all 8 inputs to the TAS5508C are less in magnitude than
the input threshold value for a programmable amount of time.
30
Description
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
•
SLES257 – SEPTEMBER 2010
Output automute: A single channel is muted when the output of the DAP section is less in magnitude
than the input threshold value for a programmable amount of time.
The detection period and thresholds for these two detectors are the same.
This time interval is selectable via I2C to be from 1 ms to 110 ms. The increments of time are 1, 2, 3, 4, 5,
10, 20, 30, 40, 50, 60, 70, 80, 90, 100, and 110 ms. This interval is independent of the sample rate. The
default value is mask programmable.
The input threshold value is an unsigned magnitude that is expressed as a bit position. This value is
adjustable via I2C. The range of the input threshold adjustment is from below the LSB (bit position 0) to
below bit position 12 in a 24-bit input-data word (bit positions 8 to 20 in the DSPE). This range provides an
input threshold that can be adjusted for 12 to 24 bits of data. The default value is mask programmable.
DVD Data Range
CD Data Range
24-Bit Input 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9
8
7
6
5
4
3
2
1
0
32 Bits in DSPE
Representation 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9
8
7
6
5
4
3
2
1
0
Threshold Range
M0013-01
Figure 2-13. Automute Threshold
The automute state is exited when the TAS5508C receives one sample that is greater than the output
threshold.
The output threshold can be one of two values:
• Equal to the input threshold
• 6 dB (one bit position) greater than the input threshold
The value for the output threshold is selectable via I2C. The default value is mask programmable.
The system latency enables the data value that is above the threshold to be preserved and output.
A mute command initiated by automute, master mute, individual I2C mute, the AM interference mute
sequence, or the bank-switch mute sequence overrides an unmute command or a volume command.
While a mute command is activated, the commanded channels transition to the mute state. When a
channel is unmuted, it goes to the last commanded volume setting that has been received for that
channel.
2.9
Loudness Compensation
The loudness compensation function compensates for the Fletcher-Munson loudness curves. The
TAS5508C loudness implementation tracks the volume control setting to provide spectral compensation
for weak low- or high-frequency response at low volume levels. For the volume tracking function, both
linear and logarithmic control laws can be implemented. Any biquad filter response can be used to provide
the desired loudness curve. The control parameters for the loudness control are programmable via the I2C
interface.
Description
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
31
TAS5508C
SLES257 – SEPTEMBER 2010
www.ti.com
The TAS5508C has a single set of loudness controls for the eight channels. In 6-channel mode, loudness
is available to the six speaker outputs and also to the line outputs. The loudness control input uses the
maximum individual master volume (V) to control the loudness that is applied to all channels. In the
192-kHz and 176.4-kHz modes, the loudness function is active only for channels 1, 2, and 8.
V
Audio In
Audio Out
Loudness
Biquad
H(z)
Loudness Function = f(V)
V
B0017-01
Figure 2-14. Loudness Compensation Functional Block Diagram
Loudness function = f(V) = G ×[2(Log V) × LG + LO] + O or alternatively,
Loudness function = f(V) = G × [VLG × 2LO] + O
For example, for the default values LG = –0.5, LO = 0, G = 1, and O = 0, then:
Loudness function = 1/SQRT(V), which is the recommended transfer function for loudness. So,
Audio out = (audio in) × V + H(Z) × SQRT(V). Other transfer functions are possible.
Table 2-6. Default Loudness Compensation Parameters
DATA
FORMAT
I2C
SUBADDRESS
Gains audio
5.23
NA
Log2 (max volume)
Loudness function
5.23
NA
0000 0000
0.0
Loudness biquad
Controls shape of
loudness curves
5.23
0x95
b0 = 0000 D513
b1 = 0000 0000
b2 = 0FFF 2AED
a1 = 00FE 5045
a2 = 0F81 AA27
b0 = 0.006503
b1 = 0
b2 = –0.006503
a1 = 1.986825
a2 = –0.986995
LG
Gain (log space)
Loudness function
5.23
0x91
FFC0 0000
–0.5
LO
Offset (log space)
Loudness function
25.23
0x92
0000 0000
0
G
Gain
Switch to enable
loudness (ON = 1, OFF = 0)
5.23
0x93
0000 0000
0
O
Offset
Provides offset
25.23
0x94
0000 0000
0
LOUDNESS
TERM
DESCRIPTION
V
Max volume
Log V
H(Z)
2.9.1
USAGE
DEFAULT
HEX
FLOAT
NA
NA
Loudness Example
Problem: Due to the Fletcher-Munson phenomena, we want to compensate for low-frequency attenuation
near 60 Hz. The TAS5508C provides a loudness transfer function with EQ gain = 6, EQ center frequency
= 60 Hz, and EQ bandwidth = 60 Hz.
Solution: Using Texas Instruments ALE TAS5508C DSP tool, Matlab™, or other signal-processing tool,
develop a loudness function with the parameters listed in Table 2-7.
32
Description
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
Table 2-7. Loudness Function Parameters
DATA
FORMAT
I2C
SUBADDRESS
Controls shape of
Loudness curves
5.23
Loudness gain
Loudness function
LO
Loudness offset
G
Gain
O
Offset
LOUDNESS
TERM
DESCRIPTION
H(Z)
Loudness biquad
LG
USAGE
DEFAULT
HEX
FLOAT
0x95
b0 = 0000 8ACE
b1 = 0000 0000
b2 = FFFF 7532
a1 = FF01 1951
a2 = 007E E914
b0 = 0.004236
b1 = 0
b2 = –0.004236
a1 = –1.991415
a2 = 0.991488
5.23
0x91
FFC0 0000
–0.5
Loudness function
25.23
0x92
0000 0000
0
Switch to enable
loudness (ON = 1, OFF = 0)
5.23
0x93
0080 0000
1
Offset
25.23
0x94
0000 0000
0
See Figure 2-15 for the resulting loudness function at different gains.
20
Gain − dB
10
0
−10
−20
−30
−40
10
100
1k
10k
20k
f − Frequency − Hz
G001
Figure 2-15. Loudness Example Plots
2.10 Dynamic Range Control (DRC)
DRC provides both compression and expansion capabilities over three separate and definable regions of
audio signal levels. Programmable threshold levels set the boundaries of the three regions. Within each of
the three regions, a distinct compression or expansion transfer function can be established and the slope
of each transfer function is determined by programmable parameters. The offset (boost or cut) at the two
boundaries defining the three regions can also be set by programmable offset coefficients. The DRC
implements the composite transfer function by computing a 5.23-format gain coefficient from each sample
output from the rms estimator. This gain coefficient is then applied to a mixer element, whose other input
is the audio data stream. The mixer output is the DRC-adjusted audio data.
There are two distinct DRC blocks in the TAS5508C. DRC1 services channels 1–7 in the 8-channel mode
and channels 1–4 and 7 in the 6-channel mode. This DRC computes rms estimates of the audio data
streams on all channels that it controls. The estimates are then compared on a sample-by-sample basis
and the larger of the estimates is used to compute the compression/expansion gain coefficient. The gain
coefficient is then applied to the appropriate channel audio streams. DRC2 services only channel 8. This
DRC also computes an rms estimate of the signal level on channel 8 and this estimate is used to compute
the compression/expansion gain coefficient applied to the channel-8 audio stream.
Description
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
33
TAS5508C
SLES257 – SEPTEMBER 2010
www.ti.com
All of the TAS5508C default values for DRC can be used except for the DRC1 decay and DRC2 decay.
Table 2-8 shows the recommended time constants and their hex values. If the user wants to implement
other DRC functions, Texas Instruments recommends using the automatic loudspeaker equalization (ALE)
tool available from Texas Instruments. The ALE tool allows the user to select the DRC transfer function
graphically. It then outputs the TAS5508C hex coefficients for download to the TAS5508C.
Table 2-8. DRC Recommended Changes From TAS5508C Defaults
I2C
SUBADDRESS
0x98
REGISTER FIELDS
RECOMMENDED TIME
CONSTANT (ms)
DRC1 energy
5
RECOMMENDED
HEX VALUE
DRC1 (1 – energy)
0x9C
DRC1 attack
DRC1 decay
DRC2 energy
0000 883F
0000 883F
007F 77C0
007F 77C0
0001 538F
0000 00AE
007E AC70
007F FF51
5
DRC2 (1 – energy)
0xA1
0000 883F
007F 77C0
2
DRC1 (1 – decay)
0x9D
0000 883F
007F 77C0
5
DRC1 (1 – attack)
DRC2 attack
0000 883F
0000 883F
007F 77C0
007F 77C0
0000 883F
0000 883F
007F 77C0
007F 77C0
0001 538F
0000 00AE
007E AC70
007F FF51
5
DRC2 (1 – attack)
DRC2 decay
2
DRC2 (1 – decay)
DEFAULT HEX
Recommended DRC set-up flow if the defaults are used:
• After power up, load the recommended hex value for DRC1 and DRC2 decay and (1 – decay). See
Table 2-8.
• Enable either the pre-volume or post-volume DRC.
Recommended DRC set-up flow if the DRC design uses values different from the defaults:
• After power up, load all DRC coefficients per the DRC design.
• Enable either the pre-volume or post-volume DRC.
Figure 2-16 shows the positioning of the DRC block in the TAS5508C processing flow. As seen, the DRC
input can come either before or after soft volume control and loudness processing.
Master
Volume
Channel Volume
Max
Volume
Bass and Treble
Bypass
DRC
Bypass
Loudness
From Input Mixer
7
Biquads
in
Series
Bass
and
Treble
To Output Mixer
Bass
and
Treble
Inline
PrePostVolume Volume
DRC
Inline
DRC
B0016-02
Figure 2-16. DRC Positioning in TAS5508C Processing Flow
Figure 2-17 illustrates a typical DRC transfer function.
34
Description
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
DRC − Compensated Output
Region
0
Region
1
Region
2
k2
k1
1:1 Transfer Function
Implemented Transfer Function
k0
O2
O1
T1
T2
DRC Input Level
M0014-01
Figure 2-17. Dynamic Range Compression (DRC) Transfer Function Structure
The three regions shown in Figure 2-17 are defined by three sets of programmable coefficients:
• Thresholds T1 and T2 define region boundaries.
• Offsets O1 and O2 define the DRC gain coefficient settings at thresholds T1 and T2, respectively.
• Slopes k0, k1, and k2 define whether compression or expansion is to be performed within a given
region. The magnitudes of the slopes define the degree of compression or expansion to be performed.
The three sets of parameters are all defined in logarithmic space and adhere to the following rules:
• The maximum input sample into the DRC is referenced at 0 dB. All values below this maximum value
then have negative values in logarithmic (dB) space.
• The samples input into the DRC are 32-bit words and consist of the upper 32 bits of the 48-bit word
format used by the digital audio processor (DAP). The 48-bit DAP word is derived from the 32-bit serial
data received at the serial-audio receive port by adding 8 bits of headroom above the 32-bit word and
8 bits of computational precision below the 32-bit word. If the audio processing steps between the SAP
input and the DRC input result in no accumulative boost or cut, the DRC operates on the 8 bits of
headroom and the 24 MSBs of the audio sample. Under these conditions, a 0-dB (maximum value)
audio sample (0x7FFF FFFF) is seen at the DRC input as a –48-dB sample (8 bits × –6.02 dB/bit =
–48 dB).
• Thresholds T1 and T2 define, in dB, the boundaries of the three regions of the DRC, as referenced to
the rms value of the data into the DRC. Zero-valued threshold settings reference the maximum-valued
rms input into the DRC and negative-valued thresholds reference all other rms input levels.
Positive-valued thresholds have no physical meaning and are not allowed. In addition, zero-valued
threshold settings are not allowed.
Although the DRC input is limited to 32-bit words, the DRC itself operates using the 48-bit word format of
the DAP. The 32-bit samples input into the DRC are placed in the upper 32 bits of this 48-bit word space.
This means that the threshold settings must be programmed as 48-bit (25.23 format) numbers.
CAUTION
Zero-valued and positive-valued threshold settings are not allowed and cause
unpredictable behavior if used.
Description
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
35
TAS5508C
SLES257 – SEPTEMBER 2010
•
•
www.ti.com
Offsets O1 and O2 define, in dB, the attenuation (cut) or gain (boost) applied by the DRC-derived gain
coefficient at the threshold points T1 and T2, respectively. Positive offsets are defined as cuts, and
thus boost or gain selections are negative numbers. Offsets must be programmed as 48-bit (25.23
format) numbers.
Slopes k0, k1, and k2 define whether compression or expansion is to be performed within a given
region, and the degree of compression or expansion to be applied. Slopes are programmed as 28-bit
(5.23 format) numbers.
2.10.1 DRC Implementation
The three elements comprising the DRC include: (1) an rms estimator, (2) a compression/expansion
coefficient computation engine, and (3) an attack/decay controller.
• RMS estimator—This DRC element derives an estimate of the rms value of the audio data stream into
the DRC. For the DRC block shared by Ch1 and Ch2, two estimates are computed—an estimate of the
Ch1 audio data stream into the DRC, and an estimate of the Ch2 audio data stream into the DRC. The
outputs of the two estimators are then compared, sample-by-sample, and the larger-valued sample is
forwarded to the compression/expansion coefficient computation engine.
Two programmable parameters, ae and (1 – ae), set the effective time window over which the rms
estimate is made. For the DRC block shared by Ch1 and Ch2, the programmable parameters apply to
both rms estimators. The time window over which the rms estimation is computed can be determined
by:
*1
t
+
window
F ȏn(1 * ae)
S
•
•
Compression/expansion coefficient computation—This DRC element converts the output of the rms
estimator to a logarithmic number, determines the region where the input resides, and then computes
and outputs the appropriate coefficient to the attack/decay element. Seven programmable parameters,
T1, T2, O1, O2, k0, k1, and k2, define the three compression/expansion regions implemented by this
element.
Attack/decay control—This DRC element controls the transition time of changes in the coefficient
computed in the compression/expansion coefficient computation element. Four programmable
parameters define the operation of this element. Parameters ad and (1 – ad) set the decay or release
time constant to be used for volume boost (expansion). Parameters aa and (1 – aa) set the attack time
constant to be used for volume cuts. The transition time constants can be determined by:
*1
*1
ta +
t +
d
F ȏn(1 * aa)
F ȏn(1 * ad)
S
S
2.10.2 Compression/Expansion Coefficient Computation Engine Parameters
There are seven programmable parameters assigned to each DRC block: two threshold parameters—T1
and T2, two offset parameters—O1 and O2, and three slope parameters—k0, k1, and k2. The threshold
parameters establish the three regions of the DRC transfer curve, the offsets anchor the transfer curve by
establishing known gain settings at the threshold levels, and the slope parameters define whether a given
region is a compression or an expansion region
The audio input stream into the DRC must pass through DRC-dedicated programmable input mixers.
These mixers are provided to scale the 32-bit input into the DRC to account for the positioning of the
audio data in the 48-bit DAP word and the net gain or attenuation in signal level between the SAP input
and the DRC. The selection of threshold values must take the gain (attenuation) of these mixers into
account. The DRC implementation examples that follow illustrate the effect these mixers have on
establishing the threshold settings.
T2 establishes the boundary between the high-volume region and the mid-volume region. T1 establishes
the boundary between the mid-volume region and the low-volume region. Both thresholds are set in
logarithmic space, and which region is active for any given rms estimator output sample is determined by
the logarithmic value of the sample.
36
Description
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
Threshold T2 serves as the fulcrum or pivot point in the DRC transfer function. O2 defines the boost
(> 0 dB) or cut (< 0 dB) implemented by the DRC-derived gain coefficient for an rms input level of T2. If
O2 = 0 dB, the value of the derived gain coefficient is 1 (0x0080 0000 in 5.23 format). k2 is the slope of
the DRC transfer function for rms input levels above T2, and k1 is the slope of the DRC transfer function
for rms input levels below T2 (and above T1). The labeling of T2 as the fulcrum stems from the fact that
there cannot be a discontinuity in the transfer function at T2. The user can, however, set the DRC
parameters to realize a discontinuity in the transfer function at the boundary defined by T1. If no
discontinuity is desired at T1, the value for the offset term O1 must obey the following equation.
O1
+ |T1 * T2|
k1 ) O2 For ( |T1| w |T2| )
No Discontinuity
T1 and T2 are the threshold settings in dB, k1 is the slope for region 1, and O2 is the offset in dB at T2. If
the user chooses to select a value of O1 that does not obey the above equation, a discontinuity at T1 is
realized.
Decreasing in volume from T2, the slope k1 remains in effect until the input level T1 is reached. If, at this
input level, the offset of the transfer function curve from the 1 : 1 transfer curve does not equal O1, there
is a discontinuity at this input level as the transfer function is snapped to the offset called for by O1. If no
discontinuity is wanted, O1 and/or k1 must be adjusted so that the value of the transfer curve at input level
T1 is offset from the 1 : 1 transfer curve by the value O1. The examples that follow illustrate both
continuous and discontinuous transfer curves at T1.
Decreasing in volume from T1, starting at offset level O1, slope k0 defines the compression/expansion
activity in the lower region of the DRC transfer curve.
2.10.2.1 Threshold Parameter Computation
For thresholds,
TdB
= –6.0206TINPUT = –6.0206TSUB_ADDRESS_ENTRY
If, for example, it is desired to set T1 = –64 dB, then the subaddress entry required to set T1 to –64 dB is:
T1
+ *64 + 10.63
SUB_ADDRESS_ENTRY
*6.0206
T1 is entered as a 48-bit number in 25.23 format. Therefore:
T1 = 10.63
= 0 1010.1010 0001 0100 0111 1010 111
= 0x0000 0550 A3D7 in 25.23 format
2.10.2.2 Offset Parameter Computation
The offsets set the boost or cut applied by the DRC-derived gain coefficient at the threshold point. An
equivalent statement is that offsets represent the departure of the actual transfer function from a 1 : 1
transfer at the threshold point. Offsets are 25.23-formatted 48-bit logarithmic numbers. They are computed
by the following equation.
O
) 24.0824 dB
O
+ DESIRED
INPUT
6.0206
Gains or boosts are represented as negative numbers; cuts or attenuations are represented as positive
numbers. For example, to achieve a boost of 21 dB at threshold T1, the I2C coefficient value entered for
O1 must be:
Description
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
37
TAS5508C
SLES257 – SEPTEMBER 2010
www.ti.com
O1
INPUT
+ –21 dB ) 24.0824 dB + 0.51197555
6.0206
+ 0.1000_0011_0001_1101_0100
+ 0x00000041886A in 25.23 format
2.10.2.3 Slope Parameter Computation
In developing the equations used to determine the subaddress of the input value required to realize a
given compression or expansion within a given region of the DRC, the following convention is adopted.
DRC transfer = Input increase : Output increase
If the DRC realizes an output increase of n dB for every dB increase in the rms value of the audio into the
DRC, a 1 : n expansion is being performed. If the DRC realizes a 1-dB increase in output level for every
n-dB increase in the rms value of the audio into the DRC, an n : 1 compression is being performed.
k=n–1
For n : 1 compression, the slope k can be found by:
k+1
n*1
In both expansion (1 : n) and compression (n : 1), n is implied to be greater than 1. Thus, for expansion:
k = n – 1 means k > 0 for n > 1. Likewise, for compression,
appears that k must always lie in the range k > –1.
k+1
n*1
means –1 < k < 0 for n > 1. Thus, it
The DRC imposes no such restriction and k can be programmed to values as negative as –15.999. To
determine what results when such values of k are entered, it is first helpful to note that the compression
and expansion equations for k are actually the same equation. For example, a 1 : 2 expansion is also a
0.5 : 1 compression.
0.5 : 1 compression å k + 1 * 1 + 1
0.5
1 : 2 expansion å k + 2 * 1 + 1
As can be seen, the same value for k is obtained either way. The ability to choose values of k less than –1
allows the DRC to implement negative-slope transfer curves within a given region. Negative-slope transfer
curves are usually not associated with compression and expansion operations, but the definition of these
operations can be expanded to include negative-slope transfer functions. For example, if k = –4
1
Compression equation: k + *4 + 1
n *1 å n + * 3 å *0.3333 : 1 compression
Expansion equation: k + *4 + n * 1 å n + *3 å 1 : *3 expansion
With k = –4, the output decreases 3 dB for every 1 dB increase in the rms value of the audio into the
DRC. As the input increases in volume, the output decreases in volume.
2.11 Output Mixer
The TAS5508C provides an 8×2 output mixer for channels 1, 2, 3, 4, 5, and 6. For channels 7 and 8, the
TAS5508C provides an 8×3 output mixer. These mixers allow each output to be any ratio of any two (or
three) signal-processed channels. The control parameters for the output crossbar mixer are programmable
via the I2C interface.
38
Description
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
Gain Coefficient
28
Select
Output
N
48
Gain Coefficient
48
28
Select
Output
N
48
48
Output
1, 2, 3, 4, 5, or 6
Output
7 or 8
Gain Coefficient
28
Select
Output
N
48
Gain Coefficient
48
28
Select
Output
N
48
48
Gain Coefficient
48
28
Select
Output
N
48
M0011-02
Figure 2-18. Output Mixers
2.12 PWM
The TAS5508C has eight channels of high-performance digital PWM modulators that are designed to
drive switching output stages (back ends) in both single-ended (SE) and H-bridge (bridge-tied load)
configurations. The TAS5508C device uses noise-shaping and sophisticated, error-correction algorithms
to achieve high power efficiency and high-performance digital audio reproduction. The TAS5508C uses an
AD1 PWM modulation scheme combined with a fifth-order noise shaper to provide a 102-dB SNR from
20 Hz to 20 kHz.
The PWM section accepts 32-bit PCM data from the DAP and outputs eight PWM audio output channels
configurable as either:
• Six channels to drive power stages and two channels to drive a differential-input active filter to provide
a separately controllable stereo lineout
• Eight channels to drive power stages
The TAS5508C PWM section output supports both single-ended and bridge-tied loads.
The PWM section provides a headphone PWM output to drive an external differential amplifier like the
TPA112. The headphone circuit uses the PWM modulator for channels 1 and 2. The headphone does not
operate while the six or eight back-end drive channels are operating. The headphone is enabled via a
headphone-select terminal or I2C command.
The PWM section has individual channel dc blocking filters that can be enabled and disabled. The filter
cutoff frequency is less than 1 Hz.
The PWM section has individual channel de-emphasis filters for 32, 44.1, and 48 kHz that can be enabled
and disabled.
Description
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
39
TAS5508C
SLES257 – SEPTEMBER 2010
www.ti.com
The PWM section also contains the power-supply volume control (PSVC) PWM.
The interpolator, noise shaper, and PWM sections provide a PWM output with the following features:
• Up to 8× oversampling
– 8× at FS = 44.1 kHz, 48 kHz, 32 kHz, 38 kHz
– 4× at FS = 88.2 kHz, 96 kHz
– 2× at FS = 176.4 kHz, 192 kHz
• Fifth-order noise shaping
• 100-dB dynamic range 0–20 kHz (TAS5508C + TAS5111 system measured at speaker terminals)
• THD < 0.01%
• Adjustable maximum modulation limit of 93.8% to 99.2%
• 3.3-V digital signal
2.12.1 DC Blocking (High-Pass Enable/Disable)
Each input channel incorporates a first-order, digital, high-pass filter to block potential dc components. The
filter –3-dB point is approximately 0.89-Hz at the 44.1-kHz sampling rate. The high-pass filter can be
enabled and disabled via the I2C interface.
2.12.2 De-Emphasis Filter
Response – dB
For audio sources that have been pre-emphasized, a precision 50-ms/15-ms de-emphasis filter is provided
to support the sampling rates of 32 kHz, 44.1 kHz, and 48 kHz. Figure 2-19 shows a graph of the
de-emphasis filtering characteristics. De-emphasis is set using two bits in the system control register.
0
De-emphasis
−10
3.18 (50 µs)
10.6 (15 µs)
f – Frequency – kHz
M0015-01
Figure 2-19. De-Emphasis Filter Characteristics
2.12.3 Power-Supply Volume Control (PSVC)
The TAS5508C supports volume control both by conventional digital gain/attenuation and by a
combination of digital and analog gain/attenuation. Varying the H-bridge power-supply voltage performs
the analog volume control function. The benefits of using power-supply volume control (PSVC) are
reduced idle channel noise, improved signal resolution at low volumes, increased dynamic range, and
reduced radio frequency emissions at reduced power levels. The PSVC is enabled via I2C. When enabled,
the PSCV provides a PWM output that is filtered to provide a reference voltage for the power supply. The
power-supply adjustment range can be set for –12.04, –18.06, or –24.08 dB, to accommodate a range of
variable power-supply designs.
Figure 2-20 and Figure 2-21 show how power-supply and digital gains can be used together.
The volume biquad (0xCF) can be used to implement a low-pass filter in the digital volume control to
match the PSVC volume transfer function.
40
Description
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
SLES257 – SEPTEMBER 2010
Digital and Power-Supply Gain − dB
www.ti.com
30
20
10
Digital Gain
0
−10
−20
−30
Power-Supply Gain
−40
−50
−60
−80
−70
−60
−50
−40
−30
−20
−10
0
10
20
30
Desired Gain − dB
G002
Figure 2-20. Power-Supply and Digital Gains (Log Space)
Digital and Power-Supply Gain − dB
100
10
Digital Gain
1
0.1
Power-Supply Gain
0.01
0.001
0.0001
0.00001
0.0001
0.001
0.01
0.1
1
10
100
Desired Gain − Linear
G003
Figure 2-21. Power-Supply and Digital Gains (Linear Space)
2.12.4 AM Interference Avoidance
Digital amplifiers can degrade AM reception as a result of their RF emissions. Texas Instruments' patented
AM interference-avoidance circuit provides a flexible system solution for a wide variety of digital audio
architectures. During AM reception, the TAS5508C adjusts the radiated emissions to provide an
emission-clear zone for the tuned AM frequency. The inputs to the TAS5508C for this operation are the
tuned AM frequency, the IF frequency, and the sample rate. The sample rate is automatically detected.
Description
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
41
TAS5508C
SLES257 – SEPTEMBER 2010
Analog
Receiver
www.ti.com
ADC
PCM1802
Audio
DSP
TAS5508C
TAS5111
TAS5111
TAS5111
TAS5111
TAS5111
Audio DSP Provides the
Master and Bit Clocks
TAS5111
TAS5111
TAS5111
Digital
Receiver
Audio
DSP
TAS5508C
TAS5111
TAS5111
TAS5111
TAS5111
The Digital Receiver or the Audio DSP
Provides the Master and Bit Clocks
TAS5111
TAS5111
TAS5111
TAS5111
Figure 2-22. Block Diagrams of Typical Systems Requiring TAS5508C Automatic AM
Interference-Avoidance Circuit
42
Description
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
3
SLES257 – SEPTEMBER 2010
TAS5508C Controls and Status
The TAS5508C provides control and status information from both the I2C registers and device pins.
This section describes some of these controls and status functions. The I2C summary and detailed
register descriptions are contained in Section 6 and Section 7.
3.1
I2C Status Registers
The TAS5508C has two status registers that provide general device information. These are the general
status register 0 (0x01) and the error status register (0x02).
3.1.1
General Status Register (0x01)
•
•
•
3.1.2
Error Status Register (0x02)
•
•
•
3.2
Device identification code
Clip indicator – The TAS5508C has a clipping indicator. Writing to the register clears the indicator.
Bank switching is busy.
No internal errors (the valid signal is high)
A clock error has occurred – These are sticky bits that are cleared by writing to the register.
– LRCLK error – when the number of MCLKs per LRCLK is incorrect
– SCLK error – when the number of SCLKS per LRCLK is incorrect
– Frame slip – when the number of MCLKs per LRCLK changes by more than 10 MCLK cycles
– PLL phase-lock error
This error status register is normally used for system development only.
TAS5508C Pin Controls
The TAS5508C provide a number of terminal controls to manage the device operation. These controls
are:
• RESET
• PDN
• BKND_ERR
• HP_SEL
• MUTE
3.2.1
Reset (RESET)
The TAS5508C is placed in the reset mode either by the power-up reset circuitry when power is applied,
or by setting the RESET terminal low.
RESET is an asynchronous control signal that restores the TAS5508C to the hard mute state (M). Master
volume is immediately set to full attenuation (there is no ramp down). Reset initiates the device reset
without an MCLK input. As long as the RESET terminal is held low, the device is in the reset state. During
reset, all I2C and serial data bus operations are ignored.
Table 3-1 shows the device output signals while RESET is active.
Table 3-1. Device Outputs During Reset
SIGNAL
SIGNAL STATE
Valid
Low
PWM P-outputs
Low (M-state)
PWM M-outputs
Low (M-state)
TAS5508C Controls and Status
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
43
TAS5508C
SLES257 – SEPTEMBER 2010
www.ti.com
Table 3-1. Device Outputs During Reset (continued)
SIGNAL
SIGNAL STATE
SDA
Signal input (not driven)
Because RESET is an asynchronous signal, clicks and pops produced during the application (the leading
edge) of RESET cannot be avoided. However, the transition from the hard mute state (M) to the
operational state is performed using a quiet start-up sequence to minimize noise. This control uses the
PWM reset and unmute sequence to shut down and start up the PWM. A detailed description of these
sequences is contained in the PWM section. If a completely quiet reset or power-down sequence is
desired, MUTE should be applied before applying RESET.
The rising edge of the reset pulse begins device initialization before the transition to the operational mode.
During device initialization, all controls are reset to their initial states. Table 3-2 shows the default control
settings following a reset.
Table 3-2. Values Set During Reset
CONTROL
44
SETTING
Clock register
Not valid
High pass
Disabled
Unmute from clock error
Hard unmute
PSVC Hi-Z
Disabled
Post DAP detection automute
Enabled
Eight Ch PreDAP detection automute
Enabled
De-emphasis
De-emphasis disabled
Channel configuration control
Configured for the default setting
Headphone configuration control
Configured for the default setting
Serial data interface format
I2S 24 bit
Individual channel mute
No channels are muted
Automute delay
5 ms
Automute threshold 1
< 8 bits
Automute threshold 2
Same as automute threshold 1
Modulation limit
Maximum modulation limit of 97.7%
Six- (or eight – low) channel configuration
Eight channels
Slew rate limit
Disengaged for all channels
Interchannel delay
–32, 0, –16, 16, –24, 8, –8, –24
Shutdown PWM on error
Enabled
Volume and mute update rate
Volume ramp 85 ms
Treble and bass slew rate
Update every 1.31 ms
Bank switching
Manual bank selection is enabled
Auto bank switching map
All channels use bank 1
Biquad coefficients (5508)
Set to all pass
Input mixer coefficients
Input N -> Channel N, no attenuation
Output mixer coefficients
Channel N -> Output N, no attenuation
Subwoofer sum into Ch1 and Ch2 (5508)
Gain of 0
Ch1 and Ch2 sum in subwoofer (5508)
Gain of 0
Bass and treble bypass
Gain of 1
Bass and treble inline
Gain of 0
DRC bypass (5508)
Gain of 1
DRC inline (5508)
Gain of 0
DRC (5508)
DRC disabled, default values
TAS5508C Controls and Status
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
Table 3-2. Values Set During Reset (continued)
CONTROL
SETTING
Master volume
Mute
Individual channel volumes
0 dB
All bass and treble Indexes
0x12 neutral
Treble filter sets
Filter set 3
Bass filter sets
Filter set 3
Loudness (5508)
Loudness disabled, default values
AM interference enable
Disabled
AM interference IF
455
AM interference select sequence
1
Tuned frequency and mode
0000, BCD
Subwoofer PSVC control
Enabled
PSVC and PSVC range
Disabled/0 dB
After the initialization time, the TAS5508C starts the transition to the operational state with the master
volume set at mute.
Because the TAS5508C has an external crystal time base, following the release of RESET, the
TAS5508C sets the MCLK and data rates and performs the initialization sequences. The PWM outputs
are held at a mute state until the master volume is set to a value other than mute via I2C.
3.2.2
Power Down (PDN)
The TAS5508C can be placed into the power-down mode by holding the PDN terminal low. When the
power-down mode is entered, both the PLL and the oscillator are shut down. Volume is immediately set to
full attenuation (there is no ramp down). This control uses the PWM mute sequence that provides a low
click and pop transition to the hard mute state (M). A detailed description of the PWM mute sequence is
contained in the PWM section.
Power down is an asynchronous operation that does not require MCLK to go into the power-down state.
To initiate the power-up sequence requires MCLK to be operational and the TAS5508C to receive 5
MCLKs prior to the release of PDN.
As long as the PDN terminal is held low, the device is in the power-down state with the PWM outputs in a
hard mute (M) state. During power down, all I2C and serial data bus operations are ignored. Table 3-3
shows the device output signals while PDN is active.
Table 3-3. Device Outputs During Power Down
SIGNAL
SIGNAL STATE
Valid
Low
PWM P-outputs
M-state = low
PWM M-outputs
M-state = low
SDA
Signal input
PSVC
M-state = low
Following the application of PDN, the TAS5508C does not perform a quiet shutdown to prevent clicks and
pops produced during the application (the leading edge) of this command. The application of PDN
immediately performs a PWM stop. A quiet stop sequence can be performed by first applying MUTE
before PDN.
When PDN is released, the system goes to the end state specified by MUTE and BKND_ERR pins and
the I2C register settings.
TAS5508C Controls and Status
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
45
TAS5508C
SLES257 – SEPTEMBER 2010
www.ti.com
The crystal time base allows the TAS5508C to determine the CLK rates. Once these rates are
determined, the TAS5508C unmutes the audio.
3.2.3
Back-End Error (BKND_ERR)
Back-end error is used to provide error management for back-end error conditions. Back-end error is a
level-sensitive signal. Back-end error can be initiated by bringing the BKND_ERR terminal low for a
minimum 5 MCLK cycles. When BKND_ERR is brought low, the PWM sets either six or eight channels
into the PWM back-end error state. This state is described in Section 2.12. Once the back-end error
sequence is initiated, a delay of 5 ms is performed before the system starts the output re-initialization
sequence. After the initialization time, the TAS5508C begins normal operation. Back-end error does not
affect other PWM modulator operations.
The number of channels that are affected by the BKND_ERR signal depends on the 6-channel
configuration signal. If the I2C setting 6-channel configuration is false, the TAS5508C places all eight
PWM outputs in the PWM back-end error state, while not affecting any other internal settings or
operations. If the I2Csetting six configuration is true, the TAS5508C brings the PWM outputs 1–6 to a
back-end error state, while not affecting any other internal settings or operations. Table 3-4 shows the
device output signal states during back-end error.
Table 3-4. Device Outputs During Back-End Error
3.2.4
SIGNAL
SIGNAL STATE
Valid
Low
PWM P-outputs
M-state – low
PWM M-outputs
M-state – low
HPPWM P-outputs
M-state – low
HPPWM M-outputs
M-state – low
SDA
Signal input (not driven)
Speaker/Headphone Selector (HP_SEL)
The HP_SEL terminal enables the headphone output or the speaker outputs. The headphone output
receives the processed data output from DAP and PWM channels 1 and 2.
In 6-channel configuration, this feature does not affect the two lineout channels.
When low, the headphone output is enabled. In this mode, the speaker outputs are disabled. When high,
the speaker outputs are enabled and the headphone is disabled.
Changes in the pin logic level result in a state change sequence using soft mute to the hard mute (M)
state for both speaker and headphone followed by a soft unmute.
When HP_SEL is low, the configuration of channels 1 and 2 is defined by the headphone configuration
register. When HP_SEL is high, the channel-1 and -2 configuration registers define the configuration of
channels 1 and 2.
3.2.5
Mute (MUTE)
The mute control provides a noiseless volume ramp to silence. Releasing mute provides a noiseless ramp
to previous volume. The TAS5508C has both master and individual channel mute commands. A terminal
is also provided for the master mute. The active-low master mute I2C register and the MUTE terminal are
logically ORed together. If either is set to low, a mute on all channels is performed. The master mute
command operates on all channels regardless of whether the system is in the 6- or 8-channel
configuration.
When MUTE is invoked, the PWM output stops switching and then goes to an idle state.
46
TAS5508C Controls and Status
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
The master mute terminal is used to support a variety of other operations in the TAS5508C, such as
setting the interchannel delay, the biquad coefficients, the serial interface format, and the clock rates. A
mute command by the master mute terminal, individual I2C mute, the AM interference mute sequence, the
bank switch mute sequence, or automute overrides an unmute command or a volume command. While a
mute is active, the commanded channels are placed in a mute state. When a channel is unmuted, it goes
to the last commanded volume setting that has been received for that channel.
3.3
Device Configuration Controls
The TAS5508C provides a number of system configuration controls that are set at initialization and
following a reset.
• Channel configuration
• Headphone configuration
• Audio system configurations
• Recovery from clock error
• Power-supply volume-control enable
• Volume and mute update rate
• Modulation index limit
• Interchannel delay
• Master clock and data rate controls
• Bank controls
3.3.1
Channel Configuration Registers
For the TAS5508C to have full control of the power stages, registers 0x05 to 0x0C must be programmed
to reflect the proper power stage and how each one should be controlled. There are eight channel
configuration registers, one for each channel.
The primary reason for using these registers is that different power stages require different handling
during start-up, mute/unmute, shutdown, and error recovery. The TAS5508C must select the sequence
that gives the best click and pop performance and ensures that the bootstrap capacitor is charged
correctly during start-up. This sequence depends on which power stage is present at the TAS5508C
output.
Table 3-5. Description of the Channel Configuration Registers (0x05 to 0x0C)
BIT
DESCRIPTION
D7
Enable/disable error recovery sequence. In case the BKND_RECOVERY pin is pulled low, this register determines if this
channel is to follow the error recovery sequence or to continue with no interruption.
D6
Determines if the power stage needs the TAS5508C VALID pin to go low to reset the power stage. Some power stages can be
reset by a combination of PWM signals. For these devices, it is recommended to set this bit low, because the VALID pin is
shared for power stages. This provides better control of each power stage.
D5
Determines if the power stage needs the TAS5508C VALID pin to go low to mute the power stage. Some power stages can be
muted by a combination of PWM signals. For these devices, it is recommended to set this bit low, because the VALID pin is
shared for power stages. This provides better control of each power stage.
D4
Inverts the PWM output. Inverting the PWM output can be an advantage if the power stage input pin is opposite the TAS5508C
PWM pinout. This makes routing on the PCB easier. To keep the phase of the output, the speaker terminals must also be
inverted.
D3
The power stage TAS5182 has a special PWM input. To ensure that the TAS5508C has full control in all occasions, the PWM
output must be remapped.
D2
Can be used to handle click and pop for some applications.
D1
This bit is normally used together with D2. For some power stages, both PWM signals must be high to get the desired operation
of both speaker outputs to be low. This bit sets the PWM outputs high-high during mute.
D0
Not used
TAS5508C Controls and Status
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
47
TAS5508C
SLES257 – SEPTEMBER 2010
www.ti.com
Table 3-6 lists the optimal setting for each output-stage configuration. Note that the default value is
applicable in all configurations except the TAS5182 SE/BTL configuration.
Table 3-6. Recommended TAS5508C Configurations for Texas Instruments Power Stages
DEVICE
ERROR RECOVERY
CONFIGURATION
D7
D6
D5
D4
D3
D2
D1
D0
BTL
1
1
1
0
0
0
0
0
SE
1
1
1
0
0
0
0
0
BTL
0
1
1
0
0
0
0
0
SE
0
1
1
0
0
0
0
0
BTL
1
1
0
0
0
0
0
0
SE
1
1
0
0
0
0
0
0
BTL
0
1
0
0
0
0
0
0
RES
TAS5111
(default)
AUT
RES
TAS5112
AUT
TAS5182
RES
SE
0
1
0
0
0
0
0
0
BTL
1
1
1
0
1
0
0
0
SE
1
1
1
0
1
0
0
0
RES: To recover from a shutdown, the output stage requires VALID to go low.
AUT: The power stage can auto-recover from a shutdown.
BTL: Bridge-tied load configuration
SE: Single-ended configuration
3.3.2
Headphone Configuration Registers
The headphone configuration controls are identical to the speaker configuration controls. The headphone
configuration control settings are used in place of the speaker configuration control settings for channels 1
and 2 when the headphones are selected. However, only one configuration setting for headphones is
used, and that is the default setting.
3.3.3
Audio System Configurations
The TAS5508C can be configured to comply with various audio systems: 5.1-channel system, 6-channel
system, 7.1-channel system, and 8-channel system.
The audio system configuration is set in the general control register (0xE0). Bits D31–D4 must be zero
and D0 is don't care.
D3
Determines if SUB is to be controlled by PSVC
D2
Enables/disables power-supply volume control
D1
Sets number of speakers in the system, including possible line outputs
D3–D1 must be configured for the audio system in the application, as shown in Table 3-7.
48
TAS5508C Controls and Status
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
Table 3-7. Audio System Configuration (General Control Register 0xE0)
Audio System
3.3.3.1
D31–D4
D3
D2
D1
D0
6 channels or 5.1 not using PSVC
0
0
0
1
X
6 channels using PSVC
0
0
1
1
X
5.1 system using PSVC
0
1
1
1
X
8 channels or 7.1 not using PSVC (default)
0
0
0
0
X
8 channels using PSVC
0
0
1
0
X
7.1 system using PSVC
0
1
1
0
X
Using Line Outputs in 6-Channel Configurations
The audio system can be configured for a 6-channel configuration (with 2 lineouts) by writing a 1 to bit D1
of register 0xE0 (general control register). In this configuration, channel-5 and -6 processing are exactly
the same as the other channels, except that the master volume has no effect.
Note that in 6-channel configuration, channels 5 and 6 are unaffected by back-end error (BKND_ERR
goes low).
To
•
•
•
•
•
•
3.3.4
use channels 5 and 6 as unprocessed lineouts, the following setup should be done:
Channel-5 volume and channel-6 volume should be set for a constant output such as 0 dB.
Bass and treble for channels 5 and 6 can be used if desired.
DRC1 should be bypassed for channels 5 and 6.
If enabled, the loudness function shapes the response of channels 5 and 6. However, the amplitude of
5 and 6 is not used in determining the loudness response.
If a down mix is desired on channels 5 and 6 as lineout, the down mixing can be performed using the
channel-5 and channel-6 input mixers.
The operation of the channel-5 and -6 biquads is unaffected by the 6-/8-channel configuration setting.
Recovery from Clock Error
The TAS5508C can be set either to perform a volume ramp up during the recovery sequence of a clock
error or simply to come up in the last state (or desired state if a volume or tone update was in progress).
This feature is enabled via I2C system control register 0x03.
3.3.5
Power-Supply Volume-Control Enable
The power-supply volume control (PSVC) can be enabled and disabled via I2C register 0xE0. The
subwoofer PWM output can be configured to be controlled by the PSVC or digitally attenuated when
PSVC is enabled (for powered subwoofer configurations). Note that PSVC cannot be simultaneously
enabled along with unmute outputs after clock error feature.
3.3.6
Volume and Mute Update Rate
The TAS5508C has fixed soft volume and mute ramp durations. The ramps are linear. The soft volume
and mute ramp rates are adjustable by programming the I2C register 0xD0 for the appropriate number of
steps to be 512, 1024, or 2048. The update is performed at a fixed rate regardless of the sample rate.
• In normal speed, the update rate is 1 step every 4/Fs seconds.
• In double speed, the update is 1 step every 8/Fs seconds.
• In quad speed, the update is 1 step every 16/Fs seconds.
Because of processor loading, the update rate can increase for some increments by 1/Fs to 3/Fs.
However, the variance of the total time to go from 18 dB to mute is less than 25%.
TAS5508C Controls and Status
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
49
TAS5508C
SLES257 – SEPTEMBER 2010
www.ti.com
Table 3-8. Volume Ramp Rates in ms
SAMPLE RATE (kHz)
NUMBER OF STEPS
3.3.7
44.1, 88.2, 176.4
32, 48, 96, 192
512
46.44 ms
42.67 ms
1024
92.88 ms
85.33 ms
2048
185.76 ms
170.67 ms
Modulation Index Limit
PWM modulation is a linear function of the audio signal. When the audio signal is 0, the PWM modulation
is 50%. When the audio signal increases toward full scale, the PWM modulation increases toward 100%.
For negative signals, the PWM modulations fall below 50% toward 0%.
However, there is a limit to the maximum modulation possible. During the offtime period, the power stage
connected to the TAS5508C output needs to get ready for the next ontime period. The maximum possible
modulation is then set by the power stage requirements. All Texas Instruments power stages need
maximum modulation to be 97.7%. This is also the default setting of the TAS5508C. Default settings can
be changed in the modulation index register (0x16).
Note that no change should be made to this register when using Texas Instruments power stages.
3.3.8
Interchannel Delay
An 8-bit value can be programmed into each of the eight PWM interchannel delay registers to add a delay
per channel from 0 to 255 clock cycles. The delays correspond to cycles of the high-speed internal clock,
DCLK. The default values are shown in Table 3-9.
Table 3-9. Interchannel Delay Default Values
I2C SUBADDRESS
CHANNEL
INTERCHANNEL DELAY DEFAULT (DCLK PERIODS)
0x1B
1
–24
0x1C
2
0
0x1D
3
–16
0x1E
4
16
0x1F
5
–24
0x20
6
8
0x21
7
–8
0x22
8
24
This delay is generated in the PWM and can be changed at any time through the serial-control interface
I2C registers 0x1B–0x22. The absolute offset for channel 1 is set in I2C subaddress 0x23.
NOTE
If used correctly, setting the PWM channel delay can optimize the performance of a
PurePath Digital™ amplifier system . The setting is based on both the type of back-end
power device that is used and the layout. These values are set during initialization using the
I2C serial interface. Unless otherwise noted, use the default values given in Table 3-9.
3.4
Master Clock and Serial Data Rate Controls
The TAS5508C functions only as a receiver of the MCLK (master clock), SCLK (shift clock), and LRCLK
(left/right clock) signals that control the flow of data on the four serial data interfaces. The 13.5-MHz
external crystal allows the TAS5508C to detect MCLK and the data rate automatically.
50
TAS5508C Controls and Status
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
The MCLK frequency can be 64 × Fs, 128 × Fs, 196 × Fs, 256 × Fs, 384 × Fs, 512 × Fs, or 768 × Fs.
The TAS5508C operates with the serial data interface signals LRCLK and SCLK synchronized to MCLK.
However, there is no constraint as to the phase relationship of these signals. The TAS5508C accepts a
64 × Fs SCLK rate and a 1 × Fs LRCLK.
If the phase of SCLK or LRCLK drifts more than ±10 MCLK cycles since the last reset, the TAS5508C
senses a clock error and resynchronizes the clock timing.
The clock and serial data interface have several control parameters:
• MCLK ratio (64 Fs, 128 Fs, 196 Fs, 256 Fs, 384 Fs, 512 Fs, or 768 Fs) – I2C parameter
• Data rate (32, 38, 44.1,48, 88.2, 96, 176.4, 192 kHz) – I2C parameter
• AM mode enable/disable – I2C parameter
During AM interference avoidance, the clock control circuitry uses three other configuration inputs:
• Tuned AM frequency (for AM interference avoidance) (550 - 1750 kHz) – I2C parameter
• Frequency set select (1–4) – I2C parameter
• Sample rate – I2C parameter or auto-detected
3.4.1
PLL Operation
The TAS5508C uses two internal clocks generated by two internal phase-locked loops (PLLs), the digital
PLL (DPLL) and the analog PLL (APLL). The APLL provides the reference clock for the PWM. The DPLL
provides the reference clock for the digital audio processor and the control logic.
The master clock MCLK input provides the input reference clock for the APLL. The external 13.5-MHz
crystal provides the input reference clock for the DPLL. The crystal provides a time base to support a
number of operations, including the detection of the MCLK ratio, the data rate, and clock error conditions.
The crystal time base provides a constant rate for all controls and signal timing.
Even if MCLK is not present, the TAS5508C can receive and store I2C commands and provide status.
3.5
Bank Controls
The TAS5508C permits the user to specify and assign sample-rate-dependent parameters for biquad,
loudness, DRC, and tone in one of three banks that can be manually selected or selected automatically
based on the data sampling rate. Each bank can be enabled for one or more specific sample rates via I2C
bank control register 0x40. Each bank set holds the following values:
• Coefficients for seven biquads (7 × 5 = 35 coefficients) for each of the eight channels (registers
0x51–0x88)
• Coefficients for one loudness biquad (register 0x95)
• DRC1 energy and (1 – energy) values (register 0x98)
• DRC1 attack, (1 – attack), decay, (1 – decay) values (register 0x9C)
• DRC2 energy and (1 – energy) values (register 0x9D)
• DRC2 attack, (1 – attack), decay, (1 – decay) values (register 0xA1)
• Five bass filter-set selections (register 0xDA)
• Five treble filter-set selections (register 0xDC)
The default selection for bank control is manual bank with bank 1 selected. Note that if bank switching is
used, bank 2 and bank 3 must be programmed on power up, because the default values are all zeroes. If
bank switching is used and bank 2 and bank 3 are not programmed correctly, then the output of the
TAS5508C could be muted when switching to those banks.
TAS5508C Controls and Status
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
51
TAS5508C
SLES257 – SEPTEMBER 2010
3.5.1
www.ti.com
Manual Bank Selection
The three bank selection bits of the bank control register allow the appropriate bank to be manually
selected (000 = bank 1, 001 = bank 2, 010 = bank 3). In the manual mode, when a write occurs to the
biquad, DRC, or loudness coefficients, the currently selected bank is updated. If audio data is streaming to
the TAS5508C during a manual bank selection, the TAS5508C first performs a mute sequence, then
performs the bank switch, and finally restores the volume using an unmute sequence.
A mute command initiated by the bank-switch mute sequence overrides an unmute command or a volume
command. While a mute is active, the commanded channels are muted. When a channel is unmuted, the
volume level goes to the last commanded volume setting that has been received for that channel.
If MCLK or SCLK is stopped, the TAS5508C performs a bank-switch operation. If the clocks start up once
the manual bank-switch command has been received, the bank-switch operation is performed during the
5-ms, silent-start sequence.
3.5.2
Automatic Bank Selection
To enable automatic bank selection, a value of 3 is written into the bank selection bits of the bank control
register. Banks are associated with one or more sample rates by writing values into the bank 1 or bank 2
data-rate selection registers. The automatic bank selection is performed when a frequency change is
detected according to the following scheme:
1. The system scans bank-1 data-rate associations to see if bank 1 is assigned for that data rate.
2. If bank 1 is assigned, then the bank-1 coefficients are loaded.
3. If bank 1 is not assigned, the system scans bank 2 to see if bank 2 is assigned for that data rate.
4. If bank 2 is assigned, the bank 2 coefficients are loaded.
5. If bank 2 is not assigned, the system loads the bank 3 coefficients.
The default is that all frequencies are enabled for bank 1. This default is expressed as a value of all 1s in
the bank-1 auto-selection byte and all 0s in the bank-2 auto-selection byte.
3.5.2.1
Coefficient Write Operations While Automatic Bank Switch Is Enabled
In automatic mode, if a write occurs to the tone, EQ, DRC, or loudness coefficients, the bank that is
written to is the current bank.
3.5.3
Bank Set
Bank set is used to provide a secure way to update the bank coefficients in both the manual and
automatic switching modes without causing a bank switch to occur. Bank-set mode does not alter the
current bank register mapping. It simply enables any bank coefficients to be updated while inhibiting any
bank switches from taking place. In manual mode, this enables the coefficients to be set without switching
banks. In automatic mode, this prevents a clock error or data rate change from corrupting a bank
coefficient write.
To update the coefficients of a bank, a value of 4, 5, or 6 is written into in the bank selection-bits of the
bank control register. This enables the tone, EQ, DRC, and loudness coefficient values of bank 1, 2, or 3,
respectively, to be updated.
Once the coefficients of the bank have been updated, the bank-selection bits are then returned to the
desired manual or automatic bank-selection mode.
3.5.4
Bank-Switch Timeline
After a bank switch is initiated (manual or automatic), no I2C writes to the TAS5508C should occur before
a minimum of 186 ms. This value is determined by the volume ramp rates for a particular sample rate.
52
TAS5508C Controls and Status
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
3.5.5
SLES257 – SEPTEMBER 2010
Bank-Switching Example 1
Problem: The audio unit containing a TAS5508C needs to handle different audio formats with different
sample rates. Format #1 requires Fs = 32 kHz, format #2 requires Fs = 44.1 kHz, and format #3 requires
Fs = 48 kHz. The sample-rate-dependent parameters in the TAS5508C require different coefficients and
data depending on the sample rate.
Strategy: Use the TAS5508C bank-switching feature to allow for managing and switching three banks
associated with the three sample rates, 32 kHz (bank 1), 44.1 kHz (bank 2), and 48 kHz (bank 3).
One possible algorithm is to generate, load, and automatically manage bank switching for this problem:
1. Generate bank-related coefficients for sample rates of 32 kHz, 44.1 kHz, and 48 kHz, and include the
same in the microprocessor-based TAS5508C I2C firmware.
2. On TAS5508C power up or reset, the microprocessor runs the following TAS5508C initialization code:
(a) Update bank 1 (write 0x0004 8040 to register 0x40).
(b) Write bank-related I2C registers with appropriate values for bank 1.
(c) Write bank 2 (write 0x0005 8040 to register 0x40).
(d) Load bank-related I2C registers with appropriate values for bank 2.
(e) Write bank 3 (write 0x0006 8040 to register 0x40).
(f) Load bank-related I2C registers with appropriate values for bank 3.
(g) Select automatic bank switching (write 0x0003 8040 to register 0x40).
3. When the audio media changes, the TAS5508C automatically detects the incoming sample rate and
automatically switches to the appropriate bank.
In this example, any sample rates other than 32 kHz and 44.1 kHz use bank 3. If other sample rates are
used, then the banks must be set up differently.
3.5.6
Bank-Switching Example 2
Problem: The audio system uses all of the sample rates supported by the TAS5508C. How can the
automatic bank switching be set up to handle this situation?
Strategy: Use the TAS5508C bank-switching feature to allow for managing and switching three banks
associated with sample rates as follows:
• Bank 1: Coefficients for 32 kHz, 38 kHz, 44.1 kHz, and 48 kHz
• Bank 2: Coefficients for 88.2kHz and 96 kHz
• Bank 3: Coefficients for 176.4 kHz and 192 kHz
One possible algorithm is to generate, load, and automatically manage bank switching for this problem:
1. Generate bank-related coefficients for sample rates 48 kHz (bank 1), 96 kHz (bank 2), and 192 kHz
(bank 3) and include the same in the microprocessor-based TAS5508C I2C firmware.
2. On TAS5508C power up or reset, the microprocessor runs the following TAS5508C initialization code:
(a) Update bank 1 (write 0x0004 F00C to register 0x40).
(b) Write bank-related I2C registers with appropriate values for bank 1.
(c) Write bank 2 (write 0x0005 F00C to register 0x40).
(d) Load bank-related I2C registers with appropriate values for bank 2.
(e) Write bank 3 (write 0x0006 F00C to register 0x40).
(f) Load bank-related I2C registers with appropriate values for bank 3.
(g) Select automatic bank switching (write 0x0003 F00C to register 0x40).
3. When the audio media changes, the TAS5508C automatically detects the incoming sample rate and
automatically switches to the appropriate bank.
TAS5508C Controls and Status
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
53
TAS5508C
SLES257 – SEPTEMBER 2010
54
www.ti.com
TAS5508C Controls and Status
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
4
Electrical Specifications
4.1
Absolute Maximum Ratings (1)
Supply voltage, DVDD and DVD_PWM
–0.3 V to 3.6 V
Supply voltage, AVDD_PLL
–0.3 V to 3.6 V
3.3-V digital input
Input voltage
–0.5 V to DVDD + 0.5 V
5 V tolerant (2) digital input
1.8 V LVCMOS
–0.5 V to 6 V
(3)
–0.5 V to VREF (4) + 0.5 V
IIK
Input clamp current (VI < 0 or VI > 1.8 V
±20 mA
IOK
Output clamp current (VO < 0 or VO > 1.8 V)
±20 mA
TA
Operating free-air temperature
Tstg
Storage temperature range
(1)
(2)
(3)
(4)
4.2
4.3
0°C to 70°C
–65°C to 150°C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
5-V tolerant inputs are RESET, PDN, MUTE, HP_SEL, SCLK, LRCLK, MCLK, SDIN1, SDIN2, SDIN3, SDIN4, SDA, and SCL.
VRA_PLL, VRD_PLL, VR_DPLL, VR_DIG, VR_PWM
VREF is a 1.8-V supply derived from regulators internal to the TAS5508C chip. VREF is on terminals VRA_PLL, VRD_PLL, VR_DPLL,
VR_DIG, and VR_PWM. These terminals are provided to permit use of external filter capacitors, but should not be used to source power
to external devices.
Dissipation Rating Table (High-k Board, 105°C Junction)
PACKAGE
TA ≤ 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
PAG
1869 mW
23.36 mW/°C
818 mW
Dynamic Performance At Recommended Operating Conditions at 25°C
PARAMETER
TEST CONDITIONS
Dynamic range 32 kHz to 192 kHz
Total harmonic distortion
Frequency response
4.4
NOM
0.1%
TAS5508C ouput
0.01%
32-kHz to 96-kHz sample rates
±0.1
176.4, 192-kHz sample rates
±0.2
UNIT
dB
dB
Recommended Operating Conditions
MIN
NOM
MAX
Digital supply voltage, DVDD and DVDD_PWM
3
3.3
3.6
V
Analog supply voltage, AVDD_PLL
3
3.3
3.6
V
High-level input voltage
5-V tolerant (1)
2
V
1.26
3.3 V
0.8
5-V tolerant (1)
0.8
VIL
Low-level input voltage
TA
Operating ambient-air temperature range
TJ
Operating junction temperature range
UNIT
2
1.8-V LVCMOS (XTL_IN)
1.8-V (XTL_IN)
(1)
MAX
102
TAS5111 at 1 W
3.3 V
VIH
MIN
TAS5508C + TAS5111 A-weighted
V
0.54
0
–20
25
70
°C
105
°C
5-V tolerant inputs are RESET, PDN, MUTE, HP_SEL, SCLK, LRCLK, MCLK, SDIN1, SDIN2, SDIN3, SDIN4, SDA, and SCL.
Electrical Specifications
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
55
TAS5508C
SLES257 – SEPTEMBER 2010
4.5
www.ti.com
Electrical Characteristics
Over recommended operating conditions (unless otherwise noted)
PARAMETER
VOH
High-level output voltage
VOL
Low-level output voltage
IOZ
High-impedance output current
TEST CONDITIONS
3.3-V TTL and 5 V
(1)
tolerant
Low-level input current
High-level input current
0.5
1.8-V LVCMOS (XTL_OUT)
IOL = 0.75 mA
0.5
1.44
3.3-V TTL
±20
(2)
VI = VIL
±1
VI = VIL
±1
VI = 0 V, DVDD = 3 V
±1
3.3-V TTL
VI = VIH
±1
1.8-V LVCMOS (XTL_IN)
VI = VIH
±1
(2)
VI = 5.5 V, DVDD = 3 V
Digital supply voltage, DVDD
Input supply current
V
mA
mA
mA
±20
Fs = 48 kHz
140
Fs = 96 kHz
150
Fs = 192 kHz
155
Power down
Analog supply voltage, AVDD
(1)
(2)
V
IOL = 4 mA
1.8-V LVCMOS (XTL_IN)
UNIT
2.4
3.3-V TTL and 5 V (1) tolerant
5 V tolerant
IDD
MAX
IOH = –0.55 mA
5 V tolerant
IIH
TYP
1.8-V LVCMOS (XTL_OUT)
3.3-V TTL
IIL
IOH = –4 mA
MIN
mA
8
Normal
20
Power down
mA
2
5-V tolerant outputs are SCL and SDA.
5-V tolerant inputs are RESET, PDN, MUTE, HP_SEL, SCLK, LRCLK, MCLK, SDIN1, SDIN2, SDIN3, SDIN4, SDA, and SCL.
4.6
PWM Operation
Over recommended operating conditions
PARAMETER
Output sample rate 1×–8× oversampled
4.7
TEST CONDITIONS
MODE
VALUE
UNIT
384
kHz
8×, 4×, or 2× sample rate
352.8
kHz
8×, 4×, or 2× sample rate
384
kHz
32-kHz data rate ±4%
12× sample rate
44.1-, 88.2-, 176.4-kHz data rate ±4%
48-, 96-, 192-kHz data rate ±4%
Switching Characteristics
4.7.1
Clock Signals
PLL input parameters and external filter components over recommended operating conditions (unless otherwise noted) (1)
PARAMETER
fXTALI
Frequency, XTAL IN
fMCLKI
Frequency, MCLK (1/tcyc2)
TEST CONDITIONS
MIN
Only use 13.5-MHz crystal ≤1000 ppm
TYP
13.5
2
MCLK duty cycle
40%
50%
56
UNIT
MHz
50
MHz
60%
MCLK minimum high time
≥2-V MCLK = 49.152 MHz, within the min
and max duty cycle constraints
5
ns
MCLK minimum low time
≤0.8-V MCLK = 49.152 MHz, within the min
and max duty cycle constraints
5
ns
LRCLK allowable drift before LRCLK reset
(1)
MAX
10
MCLKs
External PLL filter capacitor C1
SMD 0603 Y5V
100
nF
External PLL filter capacitor C2
SMD 0603 Y5V
10
nF
External PLL filter resistor R
SMD 0603, metal film
200
Ω
External VRA_PLL decoupling
SMD, Y5V
100
nF
See the TAS5508C Example Application Schematic, Section 8.
Electrical Specifications
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
4.7.2
SLES257 – SEPTEMBER 2010
Serial Audio Port
Serial audio port slave mode over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
fSCLKIN SCLK input frequency
CL = 30 pF,SCLK = 64 × Fs
MIN
TYP
2.048
MAX
UNIT
12.288
MHz
tsu1
Setup time, LRCLK to SCLK rising edge
10
ns
th1
Hold time, LRCLK from SCLK rising edge
10
ns
tsu2
Setup time, SDIN to SCLK rising edge
10
ns
th2
Hold time, SDIN from SCLK rising edge
10
LRCLK frequency
32
48
192
SCLK duty cycle
40%
50%
60%
LRCLK duty cycle
40%
50%
60%
64
64
SCLK
edges
–1/4
1/4
SCLK
period
SCLK rising edges between LRCLK rising edges
LRCLK clock edge with respect to the falling edge of
SCLK
ns
kHz
SCLK
(Input)
th1
tsu1
LRCLK
(Input)
th2
tsu2
SDIN1
SDIN2
SDIN3
T0026-01
Figure 4-1. Slave Mode Serial Data Interface Timing
Electrical Specifications
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
57
TAS5508C
SLES257 – SEPTEMBER 2010
4.7.3
www.ti.com
I2C Serial Control Port Operation
Timing characteristics for I2C interface signals over recommended operating conditions
PARAMETER
TEST CONDITIONS
MIN
fSCL
Frequency, SCL
tw(H)
Pulse duration, SCL high
No wait states
0.6
tw(L)
Pulse duration, SCL low
1.3
tr
Rise time, SCL and SDA
tf
Fall time, SCL and SDA
tsu1
Setup time, SDA to SCL
th1
Hold time, SCL to SDA
t(buf)
tsu2
MAX
UNIT
400
kHz
ms
ms
300
ns
300
ns
100
ns
0
ns
Bus free time between stop and start condition
1.3
ms
Setup time, SCL to start condition
0.6
ms
th2
Hold time, start condition to SCL
0.6
ms
tsu3
Setup time, SCL to stop condition
0.6
CL
Load capacitance for each bus line
ms
400
tw(H)
tw(L)
pF
tf
tr
SCL
tsu1
th1
SDA
T0027-01
Figure 4-2. SCL and SDA Timing
SCL
t(buf)
th2
tsu2
tsu3
SDA
Start
Condition
Stop
Condition
T0028-01
Figure 4-3. Start and Stop Conditions Timing
58
Electrical Specifications
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
4.7.4
SLES257 – SEPTEMBER 2010
Reset Timing (RESET)
Control signal parameters over recommended operating conditions (unless otherwise noted)
PARAMETER
tr(DMSTATE)
Time to M-STATE low
tw(RESET)
Pulse duration, RESET active
tr(I2C_ready)
Time to enable I2C
tr(run)
Device start-up time
MIN
TYP
400
MAX
UNIT
370
ns
None
ns
3
ms
10
ms
NOTE: Because a crystal time base is used, the system determines the CLK rates. Once the data rate and master clock ratio
is determined, the system outputs audio if a master volume command is issued.
Figure 4-4. Reset Timing
4.7.5
Power-Down (PDN) Timing
Control signal parameters over recommended operating conditions (unless otherwise noted)
PARAMETER
tp(DMSTATE)
MIN
Number of MCLKs preceding the release of PDN
tsu
TYP
Time to M-STATE low
MAX
UNIT
300
ms
5
Device start-up time
120
ms
PDN
M-State
tp(DMSTATE) < 300 ms
tsu
T0030-01
Figure 4-5. Power-Down Timing
Electrical Specifications
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
59
TAS5508C
SLES257 – SEPTEMBER 2010
4.7.6
www.ti.com
Back-End Error (BKND_ERR)
Control signal parameters over recommended operating conditions (unless otherwise noted)
PARAMETER
tw(ER)
MIN
Pulse duration, BKND_ERR active
TYP
350
tp(valid_low)
MAX
UNIT
None
ns
<100
tp(valid_high)
I2C programmable to be between 1 to 10 ms
–25
ms
25
% of interval
tw(ER)
ERR_RCVRY
M-State
Normal
Operation
Normal
Operation
tp(valid_high)
tp(valid_low)
T0031-01
Figure 4-6. Error Recovery Timing
4.7.7
Mute Timing (MUTE)
Control signal parameters over recommended operating conditions (unless otherwise noted)
PARAMETER
td(VOL)
(1)
MIN
TYP
MAX
UNIT
Defined by rate setting (1)
Volume ramp time
ms
See the Volume Treble and Base Slew Rate Register (0xD0) , Section 7.29.
MUTE
VOLUME
M-State
Normal
Operation
Normal
Operation
td(VOL)
td(VOL)
T0032-01
Figure 4-7. Mute Timing
60
Electrical Specifications
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
4.7.8
SLES257 – SEPTEMBER 2010
Headphone Select (HP_SEL)
Control signal parameters over recommended operating conditions (unless otherwise noted)
PARAMETER
tw(MUTE)
Pulse duration, HP_SEL active
td(VOL)
Soft volume update time
t(SW)
Switchover time
(1)
MIN
MAX
350
None
UNIT
ns
Defined by rate setting (1)
0.2
ms
1
ms
See the Volume Treble and Base Slew Rate Register (0xD0) , Section 7.29.
HP_SEL
Spkr Volume
td(VOL)
HP Volume
td(VOL)
t(SW)
M-State
(Internal Device State)
HP_SEL
HP Volume
td(VOL)
Spkr Volume
td(VOL)
t(SW)
M-State
T0033-01
Figure 4-8. HP_SEL Timing
Electrical Specifications
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
61
TAS5508C
SLES257 – SEPTEMBER 2010
4.7.9
www.ti.com
Volume Control
Control signal parameters over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
Maximum attenuation before mute
Individual volume, master volume, or a
combination of both
Maximum gain
Individual volume, master volume
Maximum volume before the onset of clipping
0-dB input, any modulation limit
PSVC range
PSVC enabled
UNIT
–127
dB
18
dB
0
dB
12, 18, or 24
PSVC rate
dB
Fs
PSVC modulation
Single sided
PSVC quantization
2048
PSVC PWM modulation limits
4.8
MAX
6%
(120 : 2048)
PSVC range = 24 dB
Steps
95%
(1944 : 2048)
dB
Serial Audio Interface Control and Timing
4.8.1
I 2S Timing
I2S timing uses LRCLK to define when the data being transmitted is for the left channel and when it is for the
right channel. LRCLK is low for the left channel and high for the right channel. A bit clock running at 64 × Fs is
used to clock in the data. There is a delay of one bit clock from the time the LRCLK signal changes state to the
first bit of data on the data lines. The data is written MSB first and is valid on the rising edge of the bit clock. The
TAS5508C masks unused trailing data bit positions.
2
2-Channel I S (Philips Format) Stereo Input
32 Clks
LRCLK (Note Reversed Phase)
32 Clks
Right Channel
Left Channel
SCLK
SCLK
MSB
24-Bit Mode
23 22
LSB
9
8
5
4
5
4
1
0
1
0
1
0
MSB
LSB
23 22
9
8
5
4
19 18
5
4
1
0
15 14
1
0
1
0
20-Bit Mode
19 18
16-Bit Mode
15 14
T0034-01
2
Figure 4-9. I S 64-Fs Format
62
Electrical Specifications
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
4.8.2
SLES257 – SEPTEMBER 2010
Left-Justified Timing
Left-justified (LJ) timing uses LRCLK to define when the data being transmitted is for the left channel and when it
is for the right channel. LRCLK is high for the left channel and low for the right channel. A bit clock running at 64
× Fs is used to clock in the data. The first bit of data appears on the data lines at the same time LRCLK toggles.
The data is written MSB first and is valid on the rising edge of the bit clock. The TAS5508C masks unused
trailing data bit positions.
2-Channel Left-Justified Stereo Input
32 Clks
32 Clks
Left Channel
Right Channel
LRCLK
SCLK
SCLK
MSB
24-Bit Mode
23 22
LSB
9
8
5
4
5
4
1
0
1
0
1
0
MSB
LSB
23 22
9
8
5
4
19 18
5
4
1
0
15 14
1
0
1
0
20-Bit Mode
19 18
16-Bit Mode
15 14
T0034-02
Figure 4-10. Left-Justified 64-Fs Format
Electrical Specifications
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
63
TAS5508C
SLES257 – SEPTEMBER 2010
4.8.3
www.ti.com
Right-Justified Timing
Right-justified (RJ) timing uses LRCLK to define when the data being transmitted is for the left channel and when
it is for the right channel. LRCLK is high for the left channel and low for the right channel. A bit clock running at
64 × Fs is used to clock in the data. The first bit of data appears on the data lines eight bit-clock periods (for
24-bit data) after LRCLK toggles. In RJ mode the LSB of data is always clocked by the last bit clock before
LRCLK transitions. The data is written MSB first and is valid on the rising edge of the bit clock. The TAS5508C
masks unused leading data bit positions.
2-Channel Right-Justified (Sony Format) Stereo Input
32 Clks
32 Clks
Left Channel
Right Channel
LRCLK
SCLK
SCLK
MSB
24-Bit Mode
LSB
23 22
19 18
15 14
1
0
19 18
15 14
1
0
15 14
1
0
MSB
LSB
23 22
19 18
15 14
1
0
19 18
15 14
1
0
15 14
1
0
20-Bit Mode
16-Bit Mode
T0034-03
Figure 4-11. Right-Justified 64-Fs Format
64
Electrical Specifications
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
5
SLES257 – SEPTEMBER 2010
I2C Serial-Control Interface (Slave Address 0x36)
The TAS5508C has a bidirectional I2C interface that is compatible with the Inter-IC (I2C) bus protocol and
supports both 100-kbps and 400-kbps data transfer rates for single- and multiple-byte write and read
operations. This is a slave-only device that does not support a multimaster bus environment or wait state
insertion. The control interface is used to program the registers of the device and to read device status.
The TAS5508C supports the standard-mode I2C bus operation (100 kHz maximum) and the fast I2C bus
operation (400 kHz maximum). The TAS5508C performs all I2C operations without I2C wait cycles.
5.1
General I2C Operation
The I2C bus employs two signals—SDA (data) and SCL (clock)—to communicate between integrated
circuits in a system. Data is transferred on the bus serially, one bit at a time. The address and data can be
transferred in byte (8-bit) format, with the most significant bit (MSB) transferred first. In addition, each byte
transferred on the bus is acknowledged by the receiving device with an acknowledge bit. Each transfer
operation begins with the master device driving a start condition on the bus and ends with the master
device driving a stop condition on the bus. The bus uses transitions on SDA while the clock is high to
indicate start and stop conditions. A high-to-low transition on SDA indicates a start and a low-to-high
transition indicates a stop. Normal data bit transitions must occur within the low time of the clock period.
These conditions are shown in Figure 5-1. The master generates the 7-bit slave address and the
read/write (R/W) bit to open communication with another device and then wait for an acknowledge
condition. The TAS5508C holds SDA low during the acknowledge clock period to indicate an
acknowledgement. When this occurs, the master transmits the next byte of the sequence. Each device is
addressed by a unique 7-bit slave address plus R/W bit (1 byte). All compatible devices share the same
signals via a bidirectional bus using a wired-AND connection. An external pullup resistor must be used for
the SDA and SCL signals to set the high level for the bus.
SDA
R/
A
W
7-Bit Slave Address
7
6
5
4
3
2
1
0
8-Bit Register Address (N)
7
6
5
4
3
2
1
0
8-Bit Register Data For
Address (N)
A
7
6
5
4
3
2
1
8-Bit Register Data For
Address (N)
A
0
7
6
5
4
3
2
1
A
0
SCL
Start
Stop
T0035-01
2
Figure 5-1. Typical I C Sequence
There is no limit on the number of bytes that can be transmitted between start and stop conditions. When
the last word transfers, the master generates a stop condition to release the bus. A generic data transfer
sequence is shown in Figure 5-1.
The 7-bit address for the TAS5508C is 0011011.
5.2
Single- and Multiple-Byte Transfers
The serial-control interface supports both single-byte and multiple-byte read/write operations for status
registers and the general control registers associated with the PWM. However, for the DAP data
processing registers, the serial-control interface supports only multiple-byte (four-byte) read/write
operations.
During multiple-byte read operations, the TAS5508C responds with data, a byte at a time, starting at the
subaddress assigned, as long as the master device continues to respond with acknowledges. If a
particular subaddress does not contain 32 bits, the unused bits are read as logic 0.
Copyright © 2010, Texas Instruments Incorporated
I2C Serial-Control Interface (Slave Address 0x36)
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
65
TAS5508C
SLES257 – SEPTEMBER 2010
www.ti.com
During multiple-byte write operations, the TAS5508C compares the number of bytes transmitted to the
number of bytes that are required for each specific subaddress. If a write command is received for a
biquad subaddress, the TAS5508C expects to receive five 32-bit words. If fewer than five 32-bit data
words have been received when a stop command (or another start command) is received, the data
received is discarded. Similarly, if a write command is received for a mixer coefficient, the TAS5508C
expects to receive one 32-bit word.
Supplying a subaddress for each subaddress transaction is referred to as random I2C addressing. The
TAS5508C also supports sequential I2C addressing. For write transactions, if a subaddress is issued
followed by data for that subaddress and the 15 subaddresses that follow, a sequential I2C write
transaction has taken place, and the data for all 16 subaddresses is successfully received by the
TAS5508C. For I2C sequential write transactions, the subaddress then serves as the start address and the
amount of data subsequently transmitted, before a stop or start is transmitted, determines how many
subaddresses are written. As is true for random addressing, sequential addressing requires that a
complete set of data be transmitted. If only a partial set of data is written to the last subaddress, the data
for the last subaddress is discarded. However, all other data written is accepted; only the incomplete data
is discarded.
5.3
Single-Byte Write
As shown in Figure 5-2, a single-byte, data-write transfer begins with the master device transmitting a start
condition followed by the I2C device address and the read/write bit. The read/write bit determines the
direction of the data transfer. For a write data transfer, the read/write bit is a 0. After receiving the correct
I2C device address and the read/write bit, the TAS5508C device responds with an acknowledge bit. Next,
the master transmits the address byte or bytes corresponding to the TAS5508C internal memory address
being accessed. After receiving the address byte, the TAS5508C again responds with an acknowledge bit.
Next, the master device transmits the data byte to be written to the memory address being accessed. After
receiving the data byte, the TAS5508C again responds with an acknowledge bit. Finally, the master
device transmits a stop condition to complete the single-byte, data-write transfer.
Start
Condition
Acknowledge
A6
A5
A4
A3
A2
A1
A0
Acknowledge
R/W ACK A7
A6
A5
2
I C Device Address and
Read/Write Bit
A4
A3
A2
A1
Acknowledge
A0 ACK D7
D6
Subaddress
D5
D4
D3
D2
D1
D0 ACK
Stop
Condition
Data Byte
T0481-01
Figure 5-2. Single-Byte Write Transfer
5.4
Multiple-Byte Write
A multiple-byte, data-write transfer is identical to a single-byte, data-write transfer except that multiple data
bytes are transmitted by the master device to TAS5508C, as shown in Figure 5-3. After receiving each
data byte, the TAS5508C responds with an acknowledge bit.
Start
Condition
Acknowledge
A6
A5
2
A1
A0 R/W ACK A7
I C Device Address and
Read/Write Bit
A6
A5
A4
A3
Subaddress
A1
Acknowledge
Acknowledge
Acknowledge
Acknowledge
A0 ACK D7
D0 ACK D7
D0 ACK D7
D0 ACK
First Data Byte
Other Data Bytes
Last Data Byte
Stop
Condition
T0482-01
Figure 5-3. Multiple-Byte Write Transfer
66
I2C Serial-Control Interface (Slave Address 0x36)
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
Copyright © 2010, Texas Instruments Incorporated
TAS5508C
www.ti.com
5.5
SLES257 – SEPTEMBER 2010
Incremental Multiple-Byte Write
The I2C supports a special mode which permits I2C write operations to be broken up into multiple data
write operations that are multiples of four data bytes. These are 6-byte, 10-byte, 14-byte, 18-byte, etc.,
write operations that are composed of a device address, read/write bit, subaddress, and any multiple of
four bytes of data. This permits the system to write large register values incrementally without blocking
other I2C transactions.
This feature is enabled by the append subaddress function in the TAS5508C. This function enables the
TAS5508C to append four bytes of data to a register that was opened by a previous I2C register write
operation but has not received its complete number of data bytes. Because the length of the long registers
is a multiple of four bytes, using four-byte transfers has only an integral number of append operations.
When the correct number of bytes has been received, the TAS5508C starts processing the data.
The procedure to perform an incremental multibyte-write operation is as follows:
1. Start a normal I2C write operation by sending the device address, write bit, register subaddress, and
the first four bytes of the data to be written. At the end of that sequence, send a stop condition. At this
point, the register has been opened and accepts the remaining data that is sent by writing four-byte
blocks of data to the append subaddress (0xFE).
2. At a later time, one or more append data transfers are performed to incrementally transfer the
remaining number of bytes in sequential order to complete the register write operation. Each of these
append operations is composed of the device address, write bit, append subaddress (0xFE), and four
bytes of data followed by a stop condition.
3. The operation is terminated due to an error condition, and the data is flushed:
(a) If a new subaddress is written to the TAS5508C before the correct number of bytes are written.
(b) If more or fewer than four bytes are data written at the beginning or during any of the append
operations.
(c) If a read bit is sent.
5.6
Single-Byte Read
As shown in Figure 5-4, a single-byte, data-read transfer begins with the master device transmitting a start
condition followed by the I2C device address and the read/write bit. For the data-read transfer, both a write
and then a read are actually performed. Initially, a write is performed to transfer the address byte or bytes
of the internal memory address to be read. As a result, the read/write bit is a 0. After receiving the
TAS5508C address and the read/write bit, the TAS5508C responds with an acknowledge bit. In addition,
after sending the internal memory address byte or bytes, the master device transmits another start
condition followed by the TAS5508C address and the read/write bit again. This time the read/write bit is a
1, indicating a read transfer. After receiving the TAS5508C and the read/write bit the TAS5508C again
responds with an acknowledge bit. Next, the TAS5508C transmits the data byte from the memory address
being read. After receiving the data byte, the master device transmits a not acknowledge followed by a
stop condition to complete the single-byte, data-read transfer.
Repeat Start
Condition
Start
Condition
Acknowledge
A6
A5
A1
A0 R/W ACK A7
2
I C Device Address and
Read/Write Bit
Acknowledge
A6
A5
A4
Subaddress
A0 ACK
Not
Acknowledge
Acknowledge
A6
A5
A1
A0 R/W ACK D7
2
I C Device Address and
Read/Write Bit
D6
D1
Data Byte
D0 ACK
Stop
Condition
T0483-01
Figure 5-4. Single-Byte Read Transfer
Copyright © 2010, Texas Instruments Incorporated
I2C Serial-Control Interface (Slave Address 0x36)
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
67
TAS5508C
SLES257 – SEPTEMBER 2010
5.7
www.ti.com
Multiple-Byte Read
A multiple-byte, data-read transfer is identical to a single-byte, data-read transfer except that multiple data
bytes are transmitted by the TAS5508C to the master device, as shown in Figure 5-5. Except for the last
data byte, the master device responds with an acknowledge bit after receiving each data byte.
Repeat Start
Condition
Start
Condition
Acknowledge
A6
2
A0 R/W ACK A7
I C Device Address and
Read/Write Bit
Acknowledge
A6
A5
A6
A0 ACK
Subaddress
2
Acknowledge
Acknowledge
Acknowledge
Not
Acknowledge
A0 R/W ACK D7
D0 ACK D7
D0 ACK D7
D0 ACK
I C Device Address and
Read/Write Bit
First Data Byte
Other Data Bytes
Last Data Byte
Stop
Condition
T0484-01
Figure 5-5. Multiple-Byte Read Transfer
68
I2C Serial-Control Interface (Slave Address 0x36)
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
Copyright © 2010, Texas Instruments Incorporated
TAS5508C
www.ti.com
6
SLES257 – SEPTEMBER 2010
Serial-Control I2C Register Summary
The TAS5508C slave address is 0x36. See Serial-Control Interface Register Definitions, Section 7 for
complete bit definitions.
Note that u indicates unused bits.
I2C
SUBADDRESS
TOTAL
BYTES
0x00
1
Clock control register
Set data rate and MCLK frequency
1. Fs = 48 kHz
2. MCLK = 256 Fs = 12.288 MHz
0x01
1
General status register
Clip indicator and ID code for the
TAS5508C
0x01
0x02
1
Error status register
PLL, SCLK, LRCLK, and frame slip
errors
No errors
0x03
1
System control register 1
0x04
0x05–0x0C
1
1/reg.
REGISTER FIELDS
DESCRIPTION OF CONTENTS
DEFAULT STATE
PWM high pass, clock set, unmute
select, PSVC select
1.
2.
3.
4.
PWM high pass disabled
Auto clock set
Hard unmute on clock error recovery
PSVC Hi-Z disabled
Automute and de-emphasis control
1.
2.
3.
4.
5.
Automute time-out disabled
Post-DAP detection automute enabled
8-Ch device input detection automute enabled
Unmute threshold 6 dB over input
No de-emphasis
Configure channels 1, 2, 3, 4, 5, 6, 7,
and 8
1.
2.
3.
4.
5.
6.
7.
Enable back-end reset.
Valid low for reset
Valid low for mute
Normal BEPolarity
Do not remap the output for the TAS5182.
Do not go low-low in mute.
Do not remap Hi-Z state to low-low state.
Headphone configuration
control register
Configure headphone output
1.
2.
3.
4.
5.
6.
7.
Disable back-end reset sequence.
Valid does not have to be low for reset.
Valid does not have to be low for mute.
Normal BEPolarity
Do not remap output to comply with 5182.
Do not go low-low in mute.
Do not remap Hi-Z state to low-low state.
System control register 2
Channel configuration
control registers
0x0D
1
0x0E
1
Serial data interface control
register
Set serial data interface to
right-justified, I2S, or left-justified.
24-bit I2S
0x0F
1
Soft mute register
Soft mute for channels 1, 2, 3, 4, 5, 6,
7, and 8
Unmute all channels.
0x14
1
Automute control register
Set automute delay and threshold.
1. Set automute delay = 5 ms.
2. Set automute threshold less than bit 8.
0x15
1
Automute PWM threshold
and back-end reset period
register
Set PWM automute threshold; set
back-end reset period.
1. Set the PWM threshold the same as the
TAS5508C input threshold.
2. Set back-end reset period = 5 ms.
0x16
1
Modulation index limit
register
Set modulation index.
97.7%
0x10–0x13
Reserved
0x17–0x1A
Reserved
0x1B–0x22
1/reg.
Interchannel delay registers
Set interchannel delay.
0x23
1
Channel offset register
Absolute delay offset for channel 1
(0–255)
4
Bank-switching command
register
0x24–0x3F
0x40
Channel
Channel
Channel
Channel
Channel
Channel
Channel
Channel
1 delay
2 delay
3 delay
4 delay
5 delay
6 delay
7 delay
8 delay
= –23 DCLK periods
= 0 DCLK periods
= –16 DCLK periods
= 16 DCLK periods
= –24 DCLK periods
= 8 DCLK periods
= –8 DCLK periods
= 24 DCLK periods
Minimum absolute default = 0 DCLK periods
Reserved
Set up DAP coefficients bank
switching for banks 1, 2, and 3
Manual selection – bank 1
Serial-Control I2C Register Summary
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
69
TAS5508C
SLES257 – SEPTEMBER 2010
I2C
SUBADDRESS
TOTAL
BYTES
0x41–0x48
32/reg.
www.ti.com
REGISTER FIELDS
DEFAULT STATE
Input mixer registers,
Ch1–Ch8
8×8 input crossbar mixer setup
SDIN1 –
SDIN1 –
SDIN2 –
SDIN2 –
SDIN3 –
SDIN3 –
SDIN4 –
SDIN4 –
left to input mixer 1
right to input mixer 2
left to input mixer 3
right to input mixer 4
left to input mixer 5
right to input mixer 6
left to input mixer 7
right to input mixer 8
0x49
4
ipmix_1_to_ch8
Input mixer 1 to Ch8 mixer coefficient
0.0
0x4A
4
ipmix_2_to_ch8
Input mixer 1 to Ch8 mixer coefficient
0.0
0x4B
4
ipmix_7_to_ch2
Input mixer 7 to Ch2 mixer coefficient
0.0
0x4C
4
Ch7_bp_bq2
Bypass Ch7 biquad 2 coefficient
0.0
0x4D
4
Ch7_bq2
Ch7 biquad 2 coefficient
1.0
0x4E
4
ipmix_8_to_ch12
Ch8 biquad 2 output to Ch1 mixer and
Ch2 mixer coefficient
0.0
0x4F
4
Ch8_bp_bq2
Bypass Ch8 biquad 2 coefficient 0
0.0
0x50
4
Ch8_bq2
Ch8 biquad 2 coefficient
1.0
0x51–0x88
20/reg.
Biquad filter register
Ch1–Ch8 biquad filter coefficients
All biquads = All pass for all channels
0x89–0x90
8
Bass and treble bypass
register, Ch1–Ch8
Bypass bass and treble for Ch1–Ch8
Bass and treble bypassed for all channels
0x91
4
Loudness Log2 LG
Loudness Log2 LG
0.5
0x92
8
Loudness Log2 LO
Loudness Log2 LO
0.0
0x93
4
Loudness G
Loudness G
0.0
0x94
8
Loudness O
Loudness O
0.0
Loudness biquad coefficient b0
0x00, 0x00, 0xD5, 0x13
Loudness biquad coefficient b1
0x00, 0x00, 0x00, 0x00
Loudness biquad coefficient b2
0x0F, 0xFF, 0x2A, 0xED
Loudness biquad coefficient a0
0x00, 0xFE, 0x50, 0x45
Loudness biquad coefficient a1
0x0F, 0x81, 0xAA, 0x27
0x95
20
Loudness biquad
0x96
4
DRC1 control Ch1–Ch7
DRC1 control Ch1–Ch7
DRC1 disabled in Ch1–Ch7
0x97
4
DRC2 control register, Ch8
DRC2 control Ch8
DRC2 disabled in Ch8
Ch1–Ch7, DRC1 energy
DRC1 energy
0.0041579
Ch1–Ch7, DRC1 (1 –
energy)
DRC1 (1 – energy)
0.9958421
Ch1–Ch7 DRC1 threshold
T1
DRC1 threshold (T1) – upper 2 bytes
0x00, 0x00, 0x00, 0x00
DRC1 threshold (T1) – lower 4 bytes
0x0B, 0x20, 0xE2, 0xB2
Ch1–Ch7 DRC1 threshold
T2
DRC1 threshold (T2) – upper 2 bytes
0x00, 0x00, 0x00, 0x00
DRC1 threshold (T2) – lower 4 bytes
0x06, 0xF9, 0xDE, 0x58
Ch1–Ch7 , DRC1 slope k0
DRC1 slope (k0)
0x0F, 0xC0, 0x00, 0x00
Ch1–Ch7, DRC1 slope k1
DRC1 slope (k1)
0x0F, 0xC0, 0x00, 0x00
Ch1–Ch7 DRC1 slope k2
DRC1 slope (k2)
0x0F, 0x90, 0x00, 0x00
Ch1–Ch7 DRC1 offset 1
DRC1 offset 1 (O1) – upper 2 bytes
0x00, 0x00, 0xFF, 0xFF
DRC1 offset 1 (O1) – lower 4 bytes
0xFF, 0x82, 0x30, 0x98
DRC1 offset 2 (O2) – upper 2 bytes
0x00, 0x00, 0x00, 0x00
DRC1 offset 2 (O2) – lower 4 bytes
0x01, 0x95, 0xB2, 0xC0
Ch1–Ch7 DRC1 attack
DRC1 attack
0x00, 0x00, 0x88, 0x3F
Ch1–Ch7 DRC1 (1 – attack)
DRC1 (1 – attack)
0x00, 0x7F, 0x77, 0xC0
Ch1–Ch7 DRC1 decay
DRC1 decay
0x00, 0x00, 0x00, 0xAE
Ch1–Ch7 DRC1 (1 – decay)
DRC1 (1 – decay)
0x00, 0x7F, 0xFF, 0x51
Ch8 DRC2 energy
DRC2 energy
0x00, 0x00, 0x88, 0x3F
Ch8 DRC2 (1 – energy)
DRC2 (1 – energy)
0x00, 0x7F, 0x77, 0xC0
DRC2 threshold (T1) – upper 2 bytes
0x00, 0x00, 0x00, 0x00
DRC2 threshold (T1) – lower 4 bytes
0x0B, 0x20, 0xE2, 0xB2
DRC2 threshold (T2) – upper 2 bytes
0x00, 0x00, 0x00, 0x00
DRC2 threshold (T2) – lower 4 bytes
0x06, 0xF9, 0xDE, 0x58
0x98
0x99
0x9A
0x9B
0x9C
0x9D
8
16
12
16
16
8
Ch1–Ch7 DRC1 offset 2
Ch8 DRC2 threshold T1
0x9E
16
Ch8 DRC2 threshold T2
70
DESCRIPTION OF CONTENTS
Serial-Control I2C Register Summary
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
I2C
SUBADDRESS
TOTAL
BYTES
0x9F
12
REGISTER FIELDS
DESCRIPTION OF CONTENTS
Ch8 DRC2 slope k0
DRC2 slope (k0)
0x00, 0x40, 0x00, 0x00
Ch8 DRC2 slope k1
DRC2 slope (k1)
0x0F, 0xC0, 0x00, 0x00
Ch8 DRC2 slope k2
DRC2 slope (k2)
0x0F, 0x90, 0x00, 0x00
DRC2 offset (O1) – upper 2 bytes
0x00, 0x00, 0xFF, 0xFF
DRC2 offset (O1) – lower 4 bytes
0xFF, 0x82, 0x30, 0x98
DRC2 offset (O2) – upper 2 bytes
0x00, 0x00, 0x00, 0x00
DRC2 offset (O2) – lower 4 bytes
0x01, 0x95, 0xB2, 0xC0
Ch8 DRC2 attack
DRC 2 attack
0x00, 0x00, 0x88, 0x3F
Ch8 DRC2 (1 – attack)
DRC2 (1 – attack)
0x00, 0x7F, 0x77, 0xC0
Ch8 DRC2 decay
DRC2 decay
0x00, 0x00, 0x00, 0xAE
Ch8 DRC2 (1 – decay)
DRC2 (1 – decay)
0x00, 0x7F, 0xFF, 0x51
DRC bypass 1
Ch1 DRC1 bypass coefficient
1.0
DRC inline 1
Ch1 DRC1 inline coefficient
0.0
DRC bypass 2
Ch2 DRC1 bypass coefficient
1.0
DRC inline 2
Ch2 DRC1 inline coefficient
0.0
DRC bypass 3
Ch3 DRC1 bypass coefficient
1.0
DRC inline 3
Ch3 DRC1 inline coefficient
0.0
DRC bypass 4
Ch4 DRC1 bypass coefficient
1.0
DRC inline 4
Ch4 DRC1 inline coefficient
0.0
DRC bypass 5
Ch5 DRC1 bypass coefficient
1.0
DRC inline 5
Ch5 DRC1 inline coefficient
0.0
DRC bypass 6
Ch6 DRC1 bypass coefficient
1.0
DRC inline 6
Ch6 DRC1 inline coefficient
0.0
DRC bypass 7
Ch7 DRC1 bypass coefficient
1.0
DRC inline 7
Ch7 DRC1 inline coefficient
0.0
DRC bypass 8
Ch8 DRC2 bypass coefficient
1.0
DRC inline 8
Ch8 DRC2 inline coefficient
0.0
Ch8 DRC2 offset 1
0xA0
16
Ch8 DRC2 offset 2
0xA1
0xA2
0xA3
0xA4
0xA5
0xA6
0xA7
0xA8
16
8
8
8
8
8
8
8
DEFAULT STATE
0xA9
8
0xAA
8
sel op1–8 and mix to PWM1
Select 0 to 2 of eight channels to
output mixer 1
Mix channels to PWM1
0xAB
8
sel op1–8 and mix to PWM2
Select 0 to 2 of eight channels to
output mixer 2
Mix channels to PWM2
0xAC
8
sel op1–8 and mix to PWM3
Select 0 to 2 of eight channels to
output mixer 3
Mix channels to PWM3
0xAD
8
sel op1–8 and mix to PWM4
Select 0 to 2 of eight channels to
output mixer 4
Mix channels to PWM4
0xAE
8
sel op1–8 and mix to PWM5
Select 0 to 2 of eight channels to
output mixer 5
Mix channels to PWM5
0xAF
8
sel op1–8 and mix to PWM6
Select 0 to 2 of eight channels to
output mixer 6
Mix channels to PWM6
0xB0
12
sel op1–8 and mix to PWM7
Select 0 to 3 of eight channels to
output mixer 7
Mix channels to PWM7
0xB1
12
sel op1–8 and mix to PWM8
Select 0 to 3 of eight channels to
output mixer 8
Mix channels to PWM8
0xCF
20
Volume biquad
Volume biquad
All pass
0xD0
4
Volume, treble, and bass
slew rates register
u [31:24], u [23:16], u [15:12]
VSR[11:8], TBSR[7:0]
0x00, 0x00, 0x02, 0x3F
0xD1
4
Ch1 volume
Ch1 volume
0 dB
0xD2
4
Ch2 volume
Ch2 volume
0 dB
0xD3
4
Ch3 volume
Ch3 volume
0 dB
0xD4
4
Ch4 volume
Ch4 volume
0 dB
0xD5
4
Ch5 volume
Ch5 volume
0 dB
0xD6
4
Ch6 volume
Ch6 volume
0 dB
0xD7
4
Ch7 volume
Ch7 volume
0 dB
0xD8
4
Ch8 volume
Ch8 volume
0 dB
0xB2–0xCE
Reserved
Serial-Control I2C Register Summary
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
71
TAS5508C
SLES257 – SEPTEMBER 2010
I2C
SUBADDRESS
TOTAL
BYTES
www.ti.com
REGISTER FIELDS
DESCRIPTION OF CONTENTS
0xD9
4
Master volume
Master volume
Mute
0xDA
4
Bass filter set register
Bass filter set (all channels)
Filter set 3
0xDB
4
Bass filter index register
Bass filter level (all channels)
0 dB
0xDC
4
Treble filter set register
Treble filter set (all channels)
Filter set 3
0xDD
4
Treble filter index register
Treble filter level (all channels)
0 dB
0xDE
4
AM mode register
Set up AM mode for AM-interference
reduction
AM mode disabled
Select sequence 1
IF frequency = 455 kHz
Use BCD-tuned frequency
0xDF
4
PSVC range register
Set PSVC control range
12-dB control range
0xE0
4
General control register
6- or 8-channel configuration, PSVC
enable
8-channel configuration
Power-supply volume control disabled
0xE1–0xFD
0xFE
Reserved
4 (min)
Multiple-byte write-append
register
0xFF
72
DEFAULT STATE
Special register
N/A
Reserved
Serial-Control I2C Register Summary
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
7
SLES257 – SEPTEMBER 2010
Serial-Control Interface Register Definitions
Unless otherwise noted, the I2C register default values are in bold font.
Note that u indicates unused bits.
7.1
Clock Control Register (0x00)
Bit D1 is Don't Care.
Table 7-1. Clock Control Register Format
D7
D6
D5
D4
D3
D2
0
0
0
–
–
–
–
32-kHz data rate
0
0
1
–
–
–
–
38-kHz data rate
0
1
0
–
–
–
–
44.1-kHz data rate
0
1
1
–
–
–
–
48-kHz data rate
1
0
0
–
–
–
–
88.2-kHz data rate
1
0
1
–
–
–
–
96-kHz data rate
1
1
0
–
–
–
–
176.4-kHz data rate
1
1
1
–
–
–
–
192-kHz data rate
–
–
–
0
0
0
MCLK frequency = 64
–
–
–
0
0
1
MCLK frequency = 128
–
–
–
0
1
0
MCLK frequency = 192
–
–
–
0
1
1
MCLK frequency = 256
–
–
–
1
0
0
MCLK frequency = 384
–
–
–
1
0
1
MCLK frequency = 512
–
–
–
1
1
0
MCLK frequency = 768
–
–
–
1
1
1
–
–
–
–
–
–
1
Clock register is valid (read-only)
–
–
–
–
–
–
0
Clock register is not valid (read-only)
7.2
D1
D0
FUNCTION
Reserved
General Status Register 0 (0x01)
Table 7-2. General Status Register Format
D7
D6
D5
D4
D3
D2
D1
D0
1
–
–
–
–
–
–
–
Clip indicator
FUNCTION
–
1
–
–
–
–
–
–
Bank switching busy
–
–
0
0
0
0
0
1
Identification code for TAS5508C
Serial-Control Interface Register Definitions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
73
TAS5508C
SLES257 – SEPTEMBER 2010
7.3
www.ti.com
Error Status Register (0x02)
Note that the error bits are sticky bits that are not cleared by the hardware. This means that the software
must clear the register (write zeroes) and then read them to determine if there are any persistent errors.
Table 7-3. Error Status Register Format
D7
D6
D5
D4
D3
D2
D1
D0
1
–
–
–
–
–
–
–
PLL phase lock error
–
1
–
–
–
–
–
–
PLL auto lock error
–
–
1
–
–
–
–
–
SCLK error
–
–
–
1
–
–
–
–
LRCLK error
–
–
–
–
1
–
–
–
Frame slip
0
0
0
0
0
0
0
0
No errors
7.4
FUNCTION
System Control Register 1 (0x03)
Bits D5, D2, D1, and D0 are Don't Care.
Table 7-4. System Control Register 1 Format
D7
D6
0
1
D4
D3
–
–
–
PWM high pass disabled
–
–
–
PWM high pass enabled
–
–
0
Soft unmute on recovery from clock error
–
–
1
Hard unmute on recovery from clock error
–
–
–
1
PSVC Hi-Z enable
–
–
–
0
PSVC Hi-Z disable
7.5
D5
D2
D1
D0
Function
System Control Register 2 (0x04)
Bits D3 and D2 are Don't Care.
Table 7-5. System Control Register 2 Format
D7
D6
D5
D4
D1
D0
0
–
–
–
D3
D2
–
–
Reserved
Function
–
0
–
–
–
–
PWM automute detection enabled
–
1
–
–
–
–
PWM automute detection disabled
0
–
–
–
8-Ch device input detection automute enabled
–
–
1
–
–
–
8-Ch device input detection automute disabled
–
–
–
0
–
–
Unmute threshold 6 dB over input threshold
–
–
–
1
–
–
Unmute threshold equal to input threshold
–
–
–
–
0
0
No de-emphasis
–
–
–
–
0
1
De-emphasis for Fs = 32 kHz
–
–
–
–
1
0
De-emphasis for Fs = 44.1 kHz
–
–
–
–
1
1
De-emphasis for Fs = 48 kHz
7.6
Channel Configuration Control Registers (0x05–0x0C)
Channels 1, 2, 3, 4, 5, 6, 7, and 8 are mapped into 0x05, 0x06, 0x07, 0x08, 0x09, 0x0A, 0x0B, and 0x0C,
respectively.
Bit D0 is Don't Care.
74
Serial-Control Interface Register Definitions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
Table 7-6. Channel Configuration Control Register Format
D7
D6
D5
D4
D3
D2
D1
0
–
–
–
–
–
–
Disable back-end reset sequence for a channel – BEErrorRecEn
1
–
–
–
–
–
–
Enable back-end reset sequence for a channel
–
0
–
–
–
–
–
Valid does not have to be low for this channel to be reset BEValidRst
–
1
–
–
–
–
–
Valid must be low for this channel to be reset
–
–
0
–
–
–
–
Valid does not have to be low for this channel to be muted BEValidMute
–
–
1
–
–
–
–
Valid must be low for this channel to be muted
–
–
–
0
–
–
–
Normal BEPolarity
–
–
–
1
–
–
–
Switches PWM+ and PWM– and inverts audio signal
–
–
–
–
0
–
–
Do not remap output to comply with 5182 interface
–
–
–
–
1
–
–
Remap output to comply with 5182 interface
–
–
–
–
–
0
–
Do not go to low-low in mute – BELowMute
–
–
–
–
–
1
–
Go to low-low in mute
–
–
–
–
–
–
0
Do not remap Hi-Z state to low-low state – BE5111BsMute
–
–
–
–
–
–
1
Remap Hi-Z state to low-low state
7.7
D0
FUNCTION
Headphone Configuration Control Register (0x0D)
Bit D0 is Don't Care.
Table 7-7. Headphone Configuration Control Register Format
D7
D6
D5
D4
D3
D2
D1
0
–
–
–
–
–
–
Disable back-end reset sequence for a channel – BEErrorRecEn
1
–
–
–
–
–
–
Enable back-end reset sequence for a channel
–
0
–
–
–
–
–
Valid does not have to be low for this channel to be reset
BEValidRst
–
1
–
–
–
–
–
Valid must be low for this channel to be reset
–
–
0
–
–
–
–
Valid does not have to be low for this channel to be muted
BEValidMute
–
–
1
–
–
–
–
Valid must be low for this channel to be muted
–
–
–
0
–
–
–
Normal BEPolarity
–
–
–
1
–
–
–
Switches PWM+ and PWM– and inverts audio signal
–
–
–
–
0
–
–
Do not remap output to comply with 5182 interface
–
–
–
–
1
–
–
Remap output to comply with 5182 interface
–
–
–
–
–
0
–
Do not go to low-low in mute – BELowMute
–
–
–
–
–
1
–
Go to low-low in mute
–
–
–
–
–
–
0
Do not remap Hi-Z state to low-low state – BE5111BsMute
–
–
–
–
–
–
1
Remap Hi-Z state to low-low state
7.8
D0
FUNCTION
Serial Data Interface Control Register (0x0E)
Nine serial modes can be programmed via the I2C interface.
Table 7-8. Serial Data Interface Control Register Format
RECEIVE SERIAL DATA
INTERFACE FORMAT
WORD LENGTHS
D7–D4
D3
D2
D1
D0
Right-justified
16
0000
0
0
0
0
Right-justified
20
0000
0
0
0
1
Right-justified
24
0000
0
0
1
0
Serial-Control Interface Register Definitions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
75
TAS5508C
SLES257 – SEPTEMBER 2010
www.ti.com
Table 7-8. Serial Data Interface Control Register Format (continued)
RECEIVE SERIAL DATA
INTERFACE FORMAT
7.9
WORD LENGTHS
D7–D4
D3
D2
D1
D0
I2S
16
0000
0
0
1
1
I2S
20
0000
0
1
0
0
I2S
24
0000
0
1
0
1
Left-justified
16
0000
0
1
1
0
Left-justified
20
0000
0
1
1
1
Left-justified
24
0000
1
0
0
0
Reserved
0000
1
0
0
1
Reserved
0000
1
0
1
0
Reserved
0000
1
0
1
1
Reserved
0000
1
1
0
0
Reserved
0000
1
1
0
1
Reserved
0000
1
1
1
0
Reserved
0000
1
1
1
1
Soft Mute Register (0x0F)
Table 7-9. Soft Mute Register Format
76
D7
D6
D5
D4
D3
D2
D1
D0
FUNCTION
–
–
–
–
–
–
–
1
Soft mute channel 1
–
–
–
–
–
–
1
–
Soft mute channel 2
–
–
–
–
–
1
–
–
Soft mute channel 3
–
–
–
–
1
–
–
–
Soft mute channel 4
–
–
–
1
–
–
–
–
Soft mute channel 5
–
–
1
–
–
–
–
–
Soft mute channel 6
–
1
–
–
–
–
–
–
Soft mute channel 7
1
–
–
–
–
–
–
–
Soft mute channel 8
0
0
0
0
0
0
0
0
Unmute All Channels
Serial-Control Interface Register Definitions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
7.10 Automute Control Register (0x14)
Table 7-10. Automute Control Register Format
D7
D6
D5
D4
D3
D2
D1
D0
–
–
–
–
0
0
0
0
Set input automute and PWM automute delay to 1 ms
FUNCTION
–
–
–
–
0
0
0
1
Set input automute and PWM automute delay to 2 ms
–
–
–
–
0
0
1
0
Set input automute and PWM automute delay to 3 ms
–
–
–
–
0
0
1
1
Set input automute and PWM automute delay to 4 ms
–
–
–
–
0
1
0
0
Set input automute and PWM automute delay to 5 ms
–
–
–
–
0
1
0
1
Set input automute and PWM automute delay to 10 ms
–
–
–
–
0
1
1
0
Set input automute and PWM automute delay to 20 ms
–
–
–
–
0
1
1
1
Set input automute and PWM automute delay to 30 ms
–
–
–
–
1
0
0
0
Set input automute and PWM automute delay to 40 ms
–
–
–
–
1
0
0
1
Set input automute and PWM automute delay to 50 ms
–
–
–
–
1
0
1
0
Set input automute and PWM automute delay to 60 ms
–
–
–
–
1
0
1
1
Set input automute and PWM automute delay to 70ms
–
–
–
–
1
1
0
0
Set input automute and PWM automute delay to 80 ms
–
–
–
–
1
1
0
1
Set input automute and PWM automute delay to 90 ms
–
–
–
–
1
1
1
0
Set input automute and PWM automute delay to 100 ms
–
–
–
–
1
1
1
1
Set input automute and PWM automute delay to 110 ms
0
0
0
0
–
–
–
0
0
0
1
–
–
–
–
Set input automute threshold less than bit 1 (zero input signal), lowest
automute threshold.
0
0
1
0
–
–
–
–
Set input automute threshold less than bit 2
0
0
1
1
–
–
–
–
Set input automute threshold less than bit 3
0
1
0
0
–
–
–
–
Set input automute threshold less than bit 4
0
1
0
1
–
–
–
–
Set input automute threshold less than bit 5
0
1
1
0
–
–
–
–
Set input automute threshold less than bit 6
0
1
1
1
–
–
–
–
Set input automute threshold less than bit 7
1
0
0
0
–
–
–
–
Set input automute threshold less than bit 8
1
0
0
1
–
–
–
–
Set input automute threshold less than bit 9
1
0
1
0
–
–
–
–
Set input automute threshold less than bit 10
1
0
1
1
–
–
–
–
Set input automute threshold less than bit 11
1
1
0
0
–
–
–
–
Set input automute threshold less than bit 12
1
1
0
1
–
–
–
–
Set input automute threshold less than bit 13
1
1
1
0
–
–
–
–
Set input automute threshold less than bit 14
1
1
1
1
–
–
–
–
Set input automute threshold less than bit 15
Serial-Control Interface Register Definitions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
77
TAS5508C
SLES257 – SEPTEMBER 2010
www.ti.com
7.11 Automute PWM Threshold and Back-End Reset Period Register (0x15)
Table 7-11. Automute PWM Threshold and Back-End Reset Period Register Format
D7
D6
D5
D4
D3
D2
D1
D0
0
0
0
0
–
–
–
–
Set PWM automute threshold equal to input automute threshold
0
0
0
1
–
–
–
–
Set PWM automute threshold 1 bit more than input automute threshold
0
0
1
0
–
–
–
–
Set PWM automute threshold 2 bits more than input automute threshold
0
0
1
1
–
–
–
–
Set PWM automute threshold 3 bits more than input automute threshold
0
1
0
0
–
–
–
–
Set PWM automute threshold 4 bits more than input automute threshold
0
1
0
1
–
–
–
–
Set PWM automute threshold 5 bits more than input automute threshold
0
1
1
0
–
–
–
–
Set PWM automute threshold 6 bits more than input automute threshold
0
1
1
1
–
–
–
–
Set PWM automute threshold 7 bits more than input automute threshold
1
0
0
0
–
–
–
–
Set PWM automute threshold equal to input automute threshold
1
0
0
1
–
–
–
–
Set PWM automute threshold 1 bit less than input automute threshold
1
0
1
0
–
–
–
–
Set PWM automute threshold 2 bits less than input automute threshold
1
0
1
1
–
–
–
–
Set PWM automute threshold 3 bits less than input automute threshold
1
1
0
0
–
–
–
–
Set PWM automute threshold 4 bits less than input automute threshold
1
1
0
1
–
–
–
–
Set PWM automute threshold 5 bits less than input automute threshold
1
1
1
0
–
–
–
–
Set PWM automute threshold 6 bits less than input automute threshold
1
1
1
1
–
–
–
–
Set PWM automute threshold 7 bits less than input automute threshold
–
–
–
–
0
0
0
0
Set back-end reset period < 1 ms
–
–
–
–
0
0
0
1
Set back-end reset period 1 ms
–
–
–
–
0
0
1
0
Set back-end reset period 2 ms
–
–
–
–
0
0
1
1
Set back-end reset period 3 ms
–
–
–
–
0
1
0
0
Set back-end reset period 4 ms
–
–
–
–
0
1
0
1
Set back-end reset period 5 ms
–
–
–
–
0
1
1
0
Set back-end reset period 6 ms
–
–
–
–
0
1
1
1
Set back-end reset period 7 ms
–
–
–
–
1
0
0
0
Set back-end reset period 8 ms
–
–
–
–
1
0
0
1
Set back-end reset period 9 ms
–
–
–
–
1
0
1
0
Set back-end reset period 10 ms
–
–
–
–
1
0
1
1
Set back-end reset period 10 ms
–
–
–
–
1
1
X
X
Set back-end reset period 10 ms
78
FUNCTION
Serial-Control Interface Register Definitions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
7.12 Modulation Index Limit Register (0x16)
Bits D7–D3 are Don't Care.
Table 7-12. Modulation Index Limit Register Format
D7
D6
D5
D4
D3
D2
D1
D0
LIMIT
[DCLKs]
MIN WIDTH
[DCLKs]
MODULATION
INDEX
0
0
0
1
2
99.2%
0
0
1
2
4
98.4%
0
1
0
3
6
97.7%
0
1
1
4
8
96.9%
1
0
0
5
10
96.1%
1
0
1
6
12
95.3%
1
1
0
7
14
94.5%
1
1
1
8
16
93.8%
7.13 Interchannel Delay Registers (0x1B–0x22)
Channels 1, 2, 3, 4, 5, 6, 7, and 8 are mapped into 0x1B, 0x1C, 0x1D, 0x1E, 0x1F, 0x20, 0x21, and 0x22,
respectively.
Bits D1 and D0 are Don't Care.
Table 7-13. Interchannel Delay Register Format
D7
D6
D5
D4
D3
D2
0
0
0
0
0
0
D1
D0
Minimum absolute delay, 0 DCLK cycles, default for channel 1
FUNCTION
0
1
1
1
1
1
Maximum positive delay, 31 × 4 DCLK cycles
1
0
0
0
0
0
Maximum negative delay, –32 × 4 DCLK cycles
1
0
0
0
0
0
Default value for channel 1 = –32
0
0
0
0
0
0
Default value for channel 2 = 0
1
1
0
0
0
0
Default value for channel 3 = –16
0
1
0
0
0
0
Default value for channel 4 = 16
1
0
1
0
0
0
Default value for channel 5 = –24
0
0
1
0
0
0
Default value for channel 6 = 8
1
1
1
0
0
0
Default value for channel 7 = –8
0
1
1
0
0
0
Default value for channel 8 = 24
7.14 Channel Offset Register (0x23)
The channel offset register is mapped into 0x23.
Table 7-14. Channel Offset Register Format
D7
D6
D5
D4
D3
D2
D1
D0
0
0
0
0
0
0
0
0
Minimum absolute offset, 0 DCLK cycles, default for channel 1
Function
1
1
1
1
1
1
1
1
Maximum absolute offset, 255 DCLK cycles
Serial-Control Interface Register Definitions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
79
TAS5508C
SLES257 – SEPTEMBER 2010
www.ti.com
7.15 Bank-Switching Command Register (0x40)
Bits D31–D24, D22–D19 are Don't Care.
Table 7-15. Bank-Switching Command Register Format
D31
D30
D29
D28
D27
D26
D25
D24
FUNCTION
Unused bits
D23
D22
D21
D20
D19
D18
D17
D16
FUNCTION
–
0
0
0
Manual selection bank 1
–
0
0
1
Manual selection bank 2
–
0
1
0
Manual selection bank 3
–
0
1
1
Automatic bank selection
–
1
0
0
Update the values in bank 1
–
1
0
1
Update the values in bank 2
–
1
1
0
Update the values in bank 3
–
1
1
1
Update only the bank map
0
x
x
x
Update the bank map using values in D15–D0
1
x
x
x
Do not update the bank map using values in D15–D0
D15
D14
D13
D12
D11
D10
D9
D8
1
–
–
–
–
–
–
–
32-kHz data rate—use bank 1
FUNCTION
–
1
–
–
–
–
–
–
38-kHz data rate—use bank 1
–
–
1
–
–
–
–
–
44.1-kHz data rate—use bank 1
–
–
–
1
–
–
–
–
48-kHz data rate—use bank 1
–
–
–
–
1
–
–
–
88.2-kHz data rate—use bank 1
–
–
–
–
–
1
–
–
96-kHz data rate—use bank 1
–
–
–
–
–
–
1
–
176.4-kHz data rate—use bank 1
–
–
–
–
–
–
–
1
192-kHz data rate—use bank 1
1
1
1
1
1
1
1
1
Default
D7
D6
D5
D4
D3
D2
D1
D0
1
–
–
–
–
–
–
–
32-kHz data rate—use bank 2
–
1
–
–
–
–
–
–
38-kHz data rate—use bank 2
–
–
1
–
–
–
–
–
44.1-kHz data rate—use bank 2
–
–
–
1
–
–
–
–
48-kHz data rate—use bank 2
–
–
–
–
1
–
–
–
88.2-kHz data rate—use bank 2
–
–
–
–
–
1
–
–
96-kHz data rate—use bank 2
–
–
–
–
–
–
1
–
176.4-kHz data rate—use bank 2
–
–
–
–
–
–
–
1
192-kHz data rate—use bank 2
1
1
1
1
1
1
1
1
Default
FUNCTION
7.16 Input Mixer Registers, Channels 1–8 (0x41–0x48)
Input mixers 1, 2, 3, 4, 5, 6, 7, and 8 are mapped into registers 0x41, 0x42, 0x43, 0x44, 0x45, 0x46, 0x47,
and 0x48, respectively.
Each gain coefficient is in 28-bit (5.23) format so 0x80 0000 is a gain of 1. Each gain coefficient is written
as a 32-bit word with the upper four bits not used. For 8-gain coefficients, the total is 32 bytes.
Bold indicates the one channel that is passed through the mixer.
80
Serial-Control Interface Register Definitions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
Table 7-16. Channel 1–8 Input Mixer Register Format
I2C
SUBADDRESS
0x41
0x42
0x43
TOTAL
BYTES
REGISTER
FIELDS
DESCRIPTION OF CONTENTS
DEFAULT STATE
A_to_ipmix[1]
SDIN1-left (Ch1) A to input mixer 1 coefficient (default = 1)
u[31:28], A_1[27:24], A_1[23:16], A_1[15:8], A_1[7:0]
0x00, 0x80, 0x00, 0x00
B_to_ipmix[1]
SDIN1-right (Ch2) B to input mixer 1 coefficient (default = 0)
u[31:28], B_1[27:24], B_1[23:16], B_1[15:8], B_1[7:0]
0x00, 0x00, 0x00, 0x00
C_to_ipmix[1]
SDIN2-left (Ch3) C to input mixer 1 coefficient (default = 0)
u[31:28], C_1[27:24], C_1[23:16], C_1[15:8], C_1[7:0]
0x00, 0x00, 0x00, 0x00
D_to_ipmix[1]
SDIN2-right (Ch4) D to input mixer 1 coefficient (default = 0)
u[31:28], D_1[27:24], D_1[23:16], D_1[15:8], D_1[7:0]
0x00, 0x00, 0x00, 0x00
E_to_ipmix[1]
SDIN3-left (Ch5) E to input mixer 1 coefficient (default = 0)
u[31:28], E_1[27:24], E_1[23:16], E_1[15:8], E_1[7:0]
0x00, 0x00, 0x00, 0x00
F_to_ipmix[1]
SDIN3-right (Ch6) F to input mixer 1 coefficient (default = 0)
u[31:28], F_1[27:24], F_1[23:16], F_1[15:8], F_1[7:0]
0x00, 0x00, 0x00, 0x00
G_to_ipmix[1]
SDIN4-left (Ch7) G to input mixer 1 coefficient (default = 0)
u[31:28], G_1[27:24], G_1[23:16], G_1[15:8], G_1[7:0]
0x00, 0x00, 0x00, 0x00
H_to_ipmix[1]
SDIN4-right (Ch8) H to input mixer 1 coefficient (default = 0)
u[31:28], H_1[27:24], H_1[23:16], H_1[15:8], H_1[7:0]
0x00, 0x00, 0x00, 0x00
A_to_ipmix[2]
SDIN1-left (Ch1) A to input mixer 2 coefficient (default = 0)
u[31:28], A_2[27:24], A_2[23:16], A_2[15:8], A_2[7:0]
0x00, 0x00, 0x00, 0x00
B_to_ipmix[2]
SDIN1-right (Ch2) B to input mixer 2 coefficient (default = 1)
u[31:28], B_2[27:24], B_2[23:16], B_2[15:8], B_2[7:0]
0x00, 0x80, 0x00, 0x00
C_to_ipmix[2]
SDIN2-left (Ch3) C to input mixer 2 coefficient (default = 0)
u[31:28], C_2[27:24], C_2[23:16], C_2[15:8], C_2[7:0]
0x00, 0x00, 0x00, 0x00
D_to_ipmix[2]
SDIN2-right (Ch4) D to input mixer 2 coefficient (default = 0)
u[31:28], D_2[27:24], D_2[23:16], D_2[15:8], D_2[7:0]
0x00, 0x00, 0x00, 0x00
E_to_ipmix[2]
SDIN3-left (Ch5) E to input mixer 2 coefficient (default = 0)
u[31:28], E_2[27:24], E_2[23:16], E_2[15:8], E_2[7:0]
0x00, 0x00, 0x00, 0x00
F_to_ipmix[2]
SDIN3-right (Ch6) F to input mixer 2 coefficient (default = 0)
u[31:28], F_2[27:24], F_2[23:16], F_2[15:8], F_2[7:0]
0x00, 0x00, 0x00, 0x00
G_to_ipmix[2]
SDIN4-left (Ch7) G to input mixer 2 coefficient (default = 0)
u[31:28], G_2[27:24], G_2[23:16], G_2[15:8], G_2[7:0]
0x00, 0x00, 0x00, 0x00
H_to_ipmix[2]
SDIN4-right (Ch8) H to input mixer 2 coefficient (default = 0)
u[31:28], H_2[27:24], H_2[23:16], H_2[15:8], H_2[7:0]
0x00, 0x00, 0x00, 0x00
A_to_ipmix[3]
SDIN1-left (Ch1) A to input mixer 3 coefficient (default = 0)
u[31:28], A_3[27:24], A_3[23:16], A_3[15:8], A_3[7:0]
0x00, 0x00, 0x00, 0x00
B_to_ipmix[3]
SDIN1-right (Ch2) B to input mixer 3 coefficient (default = 0)
u[31:28], B_3[27:24], B_3[23:16], B_3[15:8], B_3[7:0]
0x00, 0x00, 0x00, 0x00
C_to_ipmix[3]
SDIN2-left (Ch3) C to input mixer 3 coefficient (default = 1)
u[31:28], C_3[27:24], C_3[23:16], C_3[15:8], C_3[7:0]
0x00, 0x80, 0x00, 0x00
D_to_ipmix[3]
SDIN2-right (Ch4) D to input mixer 3 coefficient (default = 0)
u[31:28], D_3[27:24], D_3[23:16], D_3[15:8], D_3[7:0]
0x00, 0x00, 0x00, 0x00
E_to_ipmix[3]
SDIN3-left (Ch5) E to input mixer 3 coefficient (default = 0)
u[31:28], E_3[27:24], E_3[23:16], E_3[15:8], E_3[7:0]
0x00, 0x00, 0x00, 0x00
F_to_ipmix[3]
SDIN3-right (Ch6) F to input mixer 3 coefficient (default = 0)
u[31:28], F_3[27:24], F_3[23:16], F_3[15:8], F_3[7:0]
0x00, 0x00, 0x00, 0x00
G_to_ipmix[3]
SDIN4-left (Ch7) G to input mixer 3 coefficient (default = 0)
u[31:28], G_3[27:24], G_3[23:16], G_3[15:8], G_3[7:0]
0x00, 0x00, 0x00, 0x00
H_to_ipmix[3]
SDIN4-right (Ch8) H to input mixer 3 coefficient (default = 0)
u[31:28], H_3[27:24], H_3[23:16], H_3[15:8], H_3[7:0]
0x00, 0x00, 0x00, 0x00
32
32
32
Serial-Control Interface Register Definitions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
81
TAS5508C
SLES257 – SEPTEMBER 2010
www.ti.com
Table 7-16. Channel 1–8 Input Mixer Register Format (continued)
2
I C
SUBADDRESS
0x44
0x45
0x46
82
TOTAL
BYTES
REGISTER
FIELDS
DESCRIPTION OF CONTENTS
DEFAULT STATE
A_to_ipmix[4]
SDIN1-left (Ch1) A to input mixer 4 coefficient (default = 0)
u[31:28], A_4[27:24], A_4[23:16], A_4[15:8], A_4[7:0]
0x00, 0x00, 0x00, 0x00
B_to_ipmix[4]
SDIN1-right (Ch2) B to input mixer 4 coefficient (default = 0)
u[31:28], B_4[27:24], B_4[23:16], B_4[15:8], B_4[7:0]
0x00, 0x00, 0x00, 0x00
C_to_ipmix[4]
SDIN2-left (Ch3) C to input mixer 4 coefficient (default = 0)
u[31:28], C_4[27:24], C_4[23:16], C_4[15:8], C_4[7:0]
0x00, 0x00, 0x00, 0x00
D_to_ipmix[4]
SDIN2-right (Ch4) D to input mixer 4 coefficient (default = 1)
u[31:28], D_4[27:24], D_4[23:16], D_4[15:8], D_4[7:0]
0x00, 0x80, 0x00, 0x00
E_to_ipmix[4]
SDIN3-left (Ch5) E to input mixer 4 coefficient (default = 0)
u[31:28], E_4[27:24], E_4[23:16], E_4[15:8], E_4[7:0]
0x00, 0x00, 0x00, 0x00
F_to_ipmix[4]
SDIN3-right (Ch6) F to input mixer 4 coefficient (default = 0)
u[31:28], F_4[27:24], F_4[23:16], F_4[15:8], F_4[7:0]
0x00, 0x00, 0x00, 0x00
G_to_ipmix[4]
SDIN4-left (Ch7) G to input mixer 4 coefficient (default = 0)
u[31:28], G_4[27:24], G_4[23:16], G_4[15:8], G_4[7:0]
0x00, 0x00, 0x00, 0x00
H_to_ipmix[4]
SDIN4-right (Ch8) H to input mixer 4 coefficient (default = 0)
u[31:28], H_4[27:24], H_4[23:16], H_4[15:8], H_4[7:0]
0x00, 0x00, 0x00, 0x00
A_to_ipmix[5]
SDIN1-left (Ch1) A to input mixer 5 coefficient (default = 0)
u[31:28], A_5[27:24], A_5[23:16], A_5[15:8], A_5[7:0]
0x00, 0x00, 0x00, 0x00
B_to_ipmix[5]
SDIN1-right (Ch2) B to input mixer 5 coefficient (default = 0)
u[31:28], B_5[27:24], B_5[23:16], B_5[15:8], B_5[7:0]
0x00, 0x00, 0x00, 0x00
C_to_ipmix[5]
SDIN2-left (Ch3) C to input mixer 5 coefficient (default = 0)
u[31:28], C_5[27:24], C_5[23:16], C_5[15:8], C_5[7:0]
0x00, 0x00, 0x00, 0x00
D_to_ipmix[5]
SDIN2-right (Ch4) D to input mixer 5 coefficient (default = 0)
u[31:28], D_5[27:24], D_5[23:16], D_5[15:8], D_5[7:0]
0x00, 0x00, 0x00, 0x00
E_to_ipmix[5]
SDIN3-left (Ch5) E to input mixer 5 coefficient (default = 1)
u[31:28], E_5[27:24], E_5[23:16], E_5[15:8], E_5[7:0]
0x00, 0x80, 0x00, 0x00
F_to_ipmix[5]
SDIN3-right (Ch6) F to input mixer 5 coefficient (default = 0)
u[31:28], F_5[27:24], F_5[23:16], F_5[15:8], F_5[7:0]
0x00, 0x00, 0x00, 0x00
G_to_ipmix[5]
SDIN4-left (Ch7) G to input mixer 5 coefficient (default = 0)
u[31:28], G_5[27:24], G_5[23:16], G_5[15:8], G_5[7:0]
0x00, 0x00, 0x00, 0x00
H_to_ipmix[5]
SDIN4-right (Ch8) H to input mixer 5 coefficient (default = 0)
u[31:28], H_5[27:24], H_5[23:16], H_5[15:8], H_5[7:0]
0x00, 0x00, 0x00, 0x00
A_to_ipmix[6]
SDIN1-left (Ch1) A to input mixer 6 coefficient (default = 0)
u[31:28], A_6[27:24], A_6[23:16], A_6[15:8], A_6[7:0]
0x00, 0x00, 0x00, 0x00
B_to_ipmix[6]
SDIN1-right (Ch2) B to input mixer 6 coefficient (default = 0)
u[31:28], B_6[27:24], B_6[23:16], B_6[15:8], B_6[7:0]
0x00, 0x00, 0x00, 0x00
C_to_ipmix[6]
SDIN2-left (Ch3) C to input mixer 6 coefficient (default = 0)
u[31:28], C_6[27:24], C_6[23:16], C_6[15:8], C_6[7:0]
0x00, 0x00, 0x00, 0x00
D_to_ipmix[6]
SDIN2-right (Ch4) D to input mixer 6 coefficient (default = 0)
u[31:28], D_6[27:24], D_6[23:16], D_6[15:8], D_6[7:0]
0x00, 0x00, 0x00, 0x00
E_to_ipmix[6]
SDIN3-left (Ch5) E to input mixer 6 coefficient (default = 0)
u[31:28], E_6[27:24], E_6[23:16], E_6[15:8], E_6[7:0]
0x00, 0x00, 0x00, 0x00
F_to_ipmix[6]
SDIN3-right (Ch6) F to input mixer 6 coefficient (default = 1)
u[31:28], F_6[27:24], F_6[23:16], F_6[15:8], F_6[7:0]
0x00, 0x80, 0x00, 0x00
G_to_ipmix[6]
SDIN4-left (Ch7) G to input mixer 6 coefficient (default = 0)
u[31:28], G_6[27:24], G_6[23:16], G_6[15:8], G_6[7:0]
0x00, 0x00, 0x00, 0x00
H_to_ipmix[6]
SDIN4-right (Ch8) H to input mixer 6 coefficient (default = 0)
u[31:28], H_6[27:24], H_6[23:16], H_6[15:8], H_6[7:0]
0x00, 0x00, 0x00, 0x00
32
32
32
Serial-Control Interface Register Definitions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
Table 7-16. Channel 1–8 Input Mixer Register Format (continued)
2
I C
SUBADDRESS
0x47
0x48
TOTAL
BYTES
REGISTER
FIELDS
DESCRIPTION OF CONTENTS
DEFAULT STATE
A_to_ipmix[7]
SDIN1-left (Ch1) A to input mixer 7 coefficient (default = 0)
u[31:28], A_7[27:24], A_7[23:16], A_7[15:8], A_7[7:0]
0x00, 0x00, 0x00, 0x00
B_to_ipmix[7]
SDIN1-right (Ch2) B to input mixer 7 coefficient (default = 0)
u[31:28], B_7[27:24], B_7[23:16], B_7[15:8], B_7[7:0]
0x00, 0x00, 0x00, 0x00
C_to_ipmix[7]
SDIN2-left (Ch3) C to input mixer 7 coefficient (default = 0)
u[31:28], C_7[27:24], C_7[23:16], C_7[15:8], C_7[7:0]
0x00, 0x00, 0x00, 0x00
D_to_ipmix[7]
SDIN2-right (Ch4) D to input mixer 7 coefficient (default = 0)
u[31:28], D_7[27:24], D_7[23:16], D_7[15:8], D_7[7:0]
0x00, 0x00, 0x00, 0x00
E_to_ipmix[7]
SDIN3-left (Ch5) E to input mixer 7 coefficient (default = 0)
u[31:28], E_7[27:24], E_7[23:16], E_7[15:8], E_7[7:0]
0x00, 0x00, 0x00, 0x00
F_to_ipmix[7]
SDIN3-right (Ch6) F to input mixer 7 coefficient (default = 0)
u[31:28], F_7[27:24], F_7[23:16], F_7[15:8], F_7[7:0]
0x00, 0x00, 0x00, 0x00
G_to_ipmix[7]
SDIN4-left (Ch7) G to input mixer 7 coefficient (default = 1)
u[31:28], G_7[27:24], G_7[23:16], G_7[15:8], G_7[7:0]
0x00, 0x80, 0x00, 0x00
H_to_ipmix[7]
SDIN4-right (Ch8) H to input mixer 7 coefficient (default = 0)
u[31:28], H_7[27:24], H_7[23:16], H_7[15:8], H_7[7:0]
0x00, 0x00, 0x00, 0x00
A_to_ipmix[8]
SDIN1-left (Ch1) A to input mixer 8 coefficient (default = 0)
u[31:28], A_8[27:24], A_8[23:16], A_8[15:8], A_8[7:0]
0x00, 0x00, 0x00, 0x00
B_to_ipmix[8]
SDIN1-right (Ch2) B to input mixer 8 coefficient (default = 0)
u[31:28], B_8[27:24], B_8[23:16], B_8[15:8], B_8[7:0]
0x00, 0x00, 0x00, 0x00
C_to_ipmix[8]
SDIN2-left (Ch3) C to input mixer 8 coefficient (default = 0)
u[31:28], C_8[27:24], C_8[23:16], C_8[15:8], C_8[7:0]
0x00, 0x00, 0x00, 0x00
D_to_ipmix[8]
SDIN2-right (Ch4) D to input mixer 8 coefficient (default = 0)
u[31:28], D_8[27:24], D_8[23:16], D_8[15:8], D_8[7:0]
0x00, 0x00, 0x00, 0x00
E_to_ipmix[8]
SDIN3-left (Ch5) E to input mixer 8 coefficient (default = 0)
u[31:28], E_8[27:24], E_8[23:16], E_8[15:8], E_8[7:0]
0x00, 0x00, 0x00, 0x00
F_to_ipmix[8]
SDIN3-right (Ch6) F to input mixer 8 coefficient (default = 0)
u[31:28], F_8[27:24], F_8[23:16], F_8[15:8], F_8[7:0]
0x00, 0x00, 0x00, 0x00
G_to_ipmix[8]
SDIN4-left (Ch7) G to input mixer 8 coefficient (default = 0)
u[31:28], G_8[27:24], G_8[23:16], G_8[15:8], G_8[7:0]
0x00, 0x00, 0x00, 0x00
H_to_ipmix[8]
SDIN4-right (Ch8) H to input mixer 8 coefficient (default = 1)
u[31:28], H_8[27:24], H_8[23:16], H_8[15:8], H_8[7:0]
0x00, 0x80, 0x00, 0x00
32
32
Serial-Control Interface Register Definitions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
83
TAS5508C
SLES257 – SEPTEMBER 2010
www.ti.com
7.17 Bass Management Registers (0x49–0x50)
Registers 0x49–0x50 provide configuration control for bass mangement.
Each gain coefficient is in 28-bit (5.23) format so 0x80 0000 is a gain of 1. Each gain coefficient is written
as a 32-bit word with the upper four bits not used.
Table 7-17. Bass Management Register Format
SUBADDRESS
TOTAL
BYTES
REGISTER
NAME
0x49
4
ipmix_1_to_ch8
Input mixer 1 to Ch8 mixer coefficient (default = 0)
u[31:28], ipmix18[27:24], ipmix18[23:16], ipmix18[15:8],
ipmix18[7:0]
0x00, 0x00, 0x00, 0x00
0x4A
4
ipmix_2_to_ch8
Input mixer 1 to Ch8 mixer coefficient (default = 0)
u[31:28], ipmix28[27:24], ipmix28[23:16], ipmix28[15:8],
ipmix28[7:0]
0x00, 0x00, 0x00, 0x00
0x4B
4
ipmix_7_to_ch12
Input mixer 7 to Ch1 and Ch2 mixer coefficient (default = 0)
u[31:28], ipmix72[27:24], ipmix72[23:16], ipmix72[15:8],
ipmix72[7:0]
0x00, 0x00, 0x00, 0x00
0x4C
4
Ch7_bp_bq2
Ch7 biquad-2 bypass coefficient (default = 0)
u[31:28], ch7_bp_bq2[27:24], ch7_bp_bq2[23:16],
ch7_bp_bq2[15:8], ch7_bp_bq2[7:0]
0x00, 0x00, 0x00, 0x00
0x4D
4
Ch7_bq2
Ch7 biquad-2 inline coefficient (default = 1)
u[31:28], ch6_bq2[27:24], ch6_bq2[23:16], ch6_bq2[15:8],
ch6_bq2[7:0]
0x00, 0x80, 0x00, 0x00
0x4E
4
ipmix_8_to_ch12
Ch8 biquad-2 output to Ch1 mixer and Ch2 mixer coefficient
(default = 0)
u[31:28], ipmix8_12[27:24], ipmix8_12[23:16],
ipmix8_12[15:8], ipmix8_12[7:0]
0x00, 0x00, 0x00, 0x00
0x4F
4
Ch8_bp_bq2
Ch8 biquad-2 bypass coefficient (default = 0)
u[31:28], ch8_bp_bq2[27:24], ch8_bp_bq2[23:16],
ch8_bp_bq2[15:8], ch8_bp_bq2[7:0]
0x00, 0x00, 0x00, 0x00
0x50
4
Ch8_bq2
Ch8 biquad-2 inline coefficient (default = 1)
u[31:28], ch7_bq2[27:24], ch7_bq2[23:16], ch7_bq2[15:8],
ch7_bq2[7:0]
0x00, 0x80, 0x00, 0x00
DESCRIPTION OF CONTENTS
DEFAULT STATE
7.18 Biquad Filter Register (0x51–0x88)
Table 7-18. Biquad Filter Register Format
I2C
SUBADDRESS
TOTAL
BYTES
84
REGISTER
NAME
DESCRIPTION OF CONTENTS
DEFAULT
STATE
0x51–0x57
20/reg.
Ch1_bq[1:7]
Ch1 biquads 1–7. See Table 7-19 for bit definition.
See Table 7-19
0x58–0x5E
20/reg.
Ch2_bq[1:7]
Ch2 biquads 1–7. See Table 7-19 for bit definition.
See Table 7-19
0x5F–0x65
20/reg.
Ch3_bq[1:7]
Ch3 biquads 1–7. See Table 7-19 for bit definition.
See Table 7-19
0x66–0x6C
20/reg.
Ch4_bq[1:7]
Ch4 biquads 1–7. See Table 7-19 for bit definition.
See Table 7-19
0x6D–0x73
20/reg.
Ch5_bq[1:7]
Ch5 biquads 1–7. See Table 7-19 for bit definition.
See Table 7-19
0x74–0x7A
20/reg.
Ch6_bq[1:7]
Ch6 biquads 1–7. See Table 7-19 for bit definition.
See Table 7-19
0x7B–0x81
20/reg.
Ch7_bq[1:7]
Ch7 biquads 1–7. See Table 7-19 for bit definition.
See Table 7-19
0x82–0x88
20/reg.
Ch8_bq[1:7]
Ch8 biquads 1–7. See Table 7-19 for bit definition.
See Table 7-19
Serial-Control Interface Register Definitions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
Each gain coefficient is in 28-bit (5.23) format so 0x80 0000 is a gain of 1. Each gain coefficient is written
as a 32-bit word with the upper four bits not used.
Table 7-19. Contents of One 20-Byte Biquad Filter Register (Default = All-Pass)
DESCRIPTION
DEFAULT GAIN COEFFICIENT VALUES
REGISTER FIELD CONTENTS
DECIMAL
HEX
b0 coefficient
u[31:28], b0[27:24], b0[23:16], b0[15:8], b0[7:0]
1.0
0x00, 0x80, 0x00, 0x00
b1 coefficient
u[31:28], b1[27:24], b1[23:16], b1[15:8], b1[7:0]
0.0
0x00, 0x00, 0x00, 0x00
b2 coefficient
u[31:28], b2[27:24], b2[23:16], b2[15:8], b2[7:0]
0.0
0x00, 0x00, 0x00, 0x00
a1 coefficient
u[31:28], a1[27:24], a1[23:16], a1[15:8], a1[7:0]
0.0
0x00, 0x00, 0x00, 0x00
a2 coefficient
u[31:28], a2[27:24], a2[23:16], a2[15:8], a2[7:0]
0.0
0x00, 0x00, 0x00, 0x00
7.19 Bass and Treble Bypass Register, Channels 1–8 (0x89–0x90)
Channels 1, 2, 3, 4, 5, 6, 7, and 8 are mapped into registers 0x89, 0x8A, 0x8B, 0x8C, 0x8D, 0x8E, 0x8F,
and 0x90, respectively. Eight bytes are written for each channel. Each gain coefficient is in 28-bit (5.23)
format so 0x80 0000 is a gain of 1. Each gain coefficient is written as a 32-bit word with the upper four bits
not used.
Table 7-20. Channel 1–8 Bass and Treble Bypass Register Format
REGISTER
NAME
Channel bass and
treble bypass
Channel bass and
treble inline
TOTAL
BYTES
8
CONTENTS
INITIALIZATION VALUE
u[31:28], bypass[27:24], bypass[23:16], bypass[15:8], bypass[7:0]
0x00, 0x80, 0x00, 0x00
u[31:28], inline[27:24], inline[23:16], inline[15:8], inline[7:0]
0x00, 0x00, 0x00, 0x00
7.20 Loudness Registers (0x91–0x95)
Table 7-21. Loudness Register Format
I2C SUB- TOTAL
ADDRESS BYTES
0x91
4
0x92
8
0x93
4
0x94
0x95
8
20
REGISTER NAME
DESCRIPTION OF CONTENTS
DEFAULT STATE
Loudness Log2 gain (LG)
u[31:28], LG[27:24], LG[23:16], LG[15:8], LG[7:0]
0xFF, 0xC0, 0x00, 0x00
Loudness Log2 offset (LO)
u[31:24], u[23:16], LO[15:8], LO[7:0]
0x00, 0x00, 0x00, 0x00
Loudness Log2 LO
LO[31:24], LO[23:16], LO[15:8], LO[7:0]
0x00, 0x00, 0x00, 0x00
Loudness gain (G)
u[31:28], G[27:24], G[23:16], G[15:8], G[7:0]
0x00, 0x00, 0x00, 0x00
Loudness offset upper
16 bits (O)
u[31:24], u[23:16], O[15:8], O[7:0]
0x00, 0x00, 0x00, 0x00
Loudness O offset lower 32
bits (O)
O[31:24], O[23:16], O[15:8], O[7:0]
0x00, 0x00, 0x00, 0x00
Loudness biquad (b0)
u[31:28], b0[27:24], b0[23:16], b0[15:8], b0[7:0]
0x00, 0x00, 0xD5, 0x13
Loudness biquad (b1)
u[31:28], b1[27:24], b1[23:16], b1[15:8], b1[7:0]
0x00, 0x00, 0x00, 0x00
Loudness biquad (b2)
u[31:28], b2[27:24], b2[23:16], b2[15:8], b2[7:0]
0x0F, 0xFF, 0x2A, 0xED
Loudness biquad (a1)
u[31:28], a1[27:24], a1[23:16], a1[15:8], a1[7:0]
0x00, 0xFE, 0x50, 0x45
Loudness biquad (a2)
u[31:28], a2[27:24], a2[23:16], a2[15:8], a2[7:0]
0x0F, 0x81, 0xAA, 0x27
Serial-Control Interface Register Definitions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
85
TAS5508C
SLES257 – SEPTEMBER 2010
www.ti.com
7.21 DRC1 Control Registers, Channels 1–7 (0x96)
Bits D31–D14 are Don't Care.
Table 7-22. Channel 1–7 DCR1 Control Register Format
D31
D30
D29
D28
D27
D26
D25
D24
FUNCTION
Unused bits
D23
D22
D21
D20
D19
D18
D17
D16
FUNCTION
Unused bits
D15
86
D14
D13
D12
D11
D10
D9
D8
FUNCTION
0
0
–
–
–
–
Channel 1 (node j): No DRC
0
1
–
–
–
–
Channel 1 (node j): Pre-volume DRC
1
0
–
–
–
–
Channel 1 (node j): Post-volume DRC
1
1
–
–
–
–
Channel 1 (node j): No DRC
–
–
0
0
–
–
Channel 2 (node I): No DRC
–
–
0
1
–
–
Channel 2 (node I): Pre-volume DRC
–
–
1
0
–
–
Channel 2 (node I): Post-volume DRC
–
–
1
1
–
–
Channel 2 (node i): No DRC
–
–
–
–
0
0
Channel 3 (node m): No DRC
–
–
–
–
0
1
Channel 3 (node m): Pre-volume DRC
–
–
–
–
1
0
Channel 3 (node m): Post-volume DRC
–
–
–
–
1
1
Channel 3 (node m): No DRC
D7
D6
D5
D4
D3
D2
D1
D0
0
0
–
–
–
–
–
–
Channel 4 (node n): No DRC
FUNCTION
0
1
–
–
–
–
–
–
Channel 4 (node n): Pre-volume DRC
1
0
–
–
–
–
–
–
Channel 4 (node n): Post-volume DRC
1
1
–
–
–
–
–
–
Channel 4 (node n): No DRC
–
–
0
0
–
–
–
–
Channel 5 (node o): No DRC
–
–
0
1
–
–
–
–
Channel 5 (node o): Pre-volume DRC
–
–
1
0
–
–
–
–
Channel 5 (node o): Post-volume DRC
–
–
1
1
–
–
–
–
Channel 5 (node o): No DRC
–
–
–
–
0
0
–
–
Channel 6 (node p): No DRC
–
–
–
–
0
1
–
–
Channel 6 (node p): Pre-volume DRC
–
–
–
–
1
0
–
–
Channel 6 (node p): Post-volume DRC
–
–
–
–
1
1
–
–
Channel 6 (node p): No DRC
–
–
–
–
–
–
0
0
Channel 7 (node q): No DRC
–
–
–
–
–
–
0
1
Channel 7 (node q): Pre-volume DRC
–
–
–
–
–
–
1
0
Channel 7 (node q): Post-volume DRC
–
–
–
–
–
–
1
1
Channel 7 (node q): No DRC
Serial-Control Interface Register Definitions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
7.22 DRC2 Control Register, Channel 8 (0x97)
Table 7-23. Channel-8 DRC2 Control Register Format
D1
D0
0
D31–D2
0
0
0
Channel 8 (node r): no DRC
FUNCTION
0
0
0
1
Channel 8 (node r): pre-volume DRC
0
0
1
0
Channel 8 (node r): post-volume DRC
0
0
1
1
Channel 8 (node r): no DRC
7.23 DRC1 Data Registers (0x98–0x9C)
DRC1 applies to channels 1, 2, 3, 4, 5, 6, and 7.
Table 7-24. DRC1 Data Register Format
I2C
SUBADDRESS
0x98
0x99
0x9A
0x9B
0x9C
TOTAL
BYTES
8
16
12
16
16
REGISTER NAME
DESCRIPTION OF CONTENTS
DEFAULT STATE
Channel 1, 2, 3, 4, 5, 6, and 7 DRC1
energy
u[31:28], E[27:24], E[23:16], E[15:8], E[7:0]
0x00, 0x00, 0x88, 0x3F
Channel 1, 2, 3, 4, 5, 6, and 7 DRC1
(1 – energy)
u[31:28], 1–E[27:24], 1–E[23:16], 1–E[15:8], 1–E[7:0]
0x00, 0x7F, 0x77, 0xC0
Channel 1, 2, 3, 4, 5, 6, and 7 DRC1
threshold upper 16 bits (T1)
u[31:24], u[23:16], T1[15:8], T1[7:0]
0x00, 0x00, 0x00, 0x00
Channel 1, 2, 3, 4, 5, 6, and 7 DRC1
threshold lower 32 bits (T1)
T1[31:24], T1[23:16], T1[15:8], T1[7:0]
0x0B, 0x20, 0xE2, 0xB2
Channel 1, 2, 3, 4, 5, 6, and 7 DRC1
threshold upper 16 bits (T2)
u[31:24], u[23:16], T2[15:8], T2[7:0]
0x00, 0x00, 0x00, 0x00
Channel 1, 2, 3, 4, 5, 6, and 7 DRC1
threshold lower 32 bits (T2)
T2[31:24], T2[23:16], T2[15:8], T2[7:0]
0x06, 0xF9, 0xDE, 0x58
Channel 1, 2, 3, 4, 5, 6, and 7 DRC1
slope (k0)
u[31:28], k0[27:24], k0[23:16], k0[15:8], k0[7:0]
0x00, 0x40, 0x00, 0x00
Channel 1, 2, 3, 4, 5, 6, and 7 DRC1
slope (k1)
u[31:28], k1[27:24], k1[23:16], k1[15:8], k1[7:0]
0x0F, 0xC0, 0x00, 0x00
Channel 1, 2, 3, 4, 5, 6, and 7 DRC1
slope (k2)
u[31:28], k2[27:24], k2[23:16], k2[15:8], k2[7:0]
0x0F, 0x90, 0x00, 0x00
Channel 1, 2, 3, 4, 5, 6, and 7 DRC1
offset 1 upper 16 bits (O1)
u[31:24], u[23:16], O1[15:8], O1[7:0]
0x00, 0x00, 0xFF, 0xFF
Channel 1, 2, 3, 4, 5, 6, and 7 DRC1
offset 1 lower 32 bits (O1)
O1[31:24], O1[23:16], O1[15:8], O1[7:0]
0xFF, 0x82, 0x30, 0x98
Channel 1, 2, 3, 4, 5, 6, and 7 DRC1
offset 2 upper 16 bits (O2)
u[31:24], u[23:16], O2[15:8], O2[7:0]
0x00, 0x00, 0x00, 0x00
Channel 1, 2, 3, 4, 5, 6, and 7 DRC1
offset 2 lower 32 bits (O2)
O2[31:24], O2[23:16], O2[15:8], O2[7:0]
0x01, 0x95, 0xB2, 0xC0
Channel 1, 2, 3, 4, 5, 6, and 7 DRC1
attack
u[31:28], A[27:24], A[23:16], A[15:8], A[7:0]
0x00, 0x00, 0x88, 0x3F
Channel 1, 2, 3, 4, 5, 6, and 7 DRC1
(1 – attack)
u[31:28], 1–A[27:24], 1–A[23:16], 1–A[15:8], 1–A[7:0]
0x00, 0x7F, 0x77, 0xC0
Channel 1, 2, 3, 4, 5, 6, and 7 DRC1
decay
u[31:28], D[27:24], D[23:16], D[15:8], D[7:0]
0x00, 0x00, 0x00, 0x56
Channel 1, 2, 3, 4, 5, 6, and 7 DRC1
(1 – decay)
u[31:28], 1–D[27:24], 1–D[23:16], 1–D[15:8], 1–D[7:0]
0x00, 0x3F, 0xFF, 0xA8
Serial-Control Interface Register Definitions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
87
TAS5508C
SLES257 – SEPTEMBER 2010
www.ti.com
7.24 DRC2 Data Registers (0x9D–0xA1)
DRC2 applies to channel 8.
Table 7-25. DRC2 Data Register Format
I2C
SUBADDRESS
TOTAL
BYTES
0x9D
8
0x9E
0x9F
0xA0
0xA1
16
12
16
16
REGISTER NAME
DESCRIPTION OF CONTENTS
DEFAULT STATE
Channel 8 DRC2 energy
u[31:28], E[27:24], E[23:16], E[15:8], E[7:0]
0x00, 0x00, 0x88, 0x3F
Channel 8 DRC2 (1 – energy)
u[31:28], 1–E[27:24], 1–E[23:16], 1–E[15:8], 1–E[7:0]
0x00, 0x7F, 0x77, 0xC0
Channel 8 DRC2 threshold
upper 16 bits (T1)
u[31:24], u[23:16], T1[15:8], T1[7:0]
0x00, 0x00, 0x00, 0x00
Channel 8 DRC2 threshold
lower 32 bits (T1)
T1[31:24], T1[23:16], T1[15:8], T1[7:0]
0x0B, 0x20, 0xE2, 0xB2
Channel 8 DRC2 threshold
upper 16 bits (T2)
u[31:24], u[23:16], T2[15:8], T2[7:0]
0x00, 0x00, 0x00, 0x00
Channel 8 DRC2 threshold
lower 32 bits (T2)
T2[31:24], T2[23:16], T2[15:8], T2[7:0]
0x06, 0xF9, 0xDE, 0x58
Channel 8 DRC2 slope (k0)
u[31:28], k0[27:24], k0[23:16], k0[15:8], k0[7:0]
0x00, 0x40, 0x00, 0x00
Channel 8 DRC2 slope (k1)
u[31:28], k1[27:24], k1[23:16], k1[15:8], k1[7:0]
0x0F, 0xC0, 0x00, 0x00
Channel 8 DRC2 slope (k2)
u[31:28], k2[27:24], k2[23:16], k2[15:8], k2[7:0]
0x0F, 0x90, 0x00, 0x00
Channel 8 DRC2 offset 1 upper u[31:24], u[23:16], O1[15:8], O1[7:0]
16 bits (O1)
0x00, 0x00, 0xFF, 0xFF
Channel 8 DRC2 offset 1 lower
32 bits (O1)
0xFF, 0x82, 0x30, 0x98
O1[31:24], O1[23:16], O1[15:8], O1[7:0]
Channel 8 DRC2 offset 2 upper u[31:24], u[23:16], O2[15:8], O2[7:0]
16 bits (O2)
0x00, 0x00, 0x00, 0x00
Channel 8 DRC2 offset 2 lower
32 bits (O2)
O2[31:24], O2[23:16], O2[15:8], O2[7:0]
0x01, 0x95, 0xB2, 0xC0
Channel 8 DRC2 attack
u[31:28], A[27:24], A[23:16], A[15:8], A[7:0]
0x00, 0x00, 0x88, 0x3F
Channel 8 DRC2 (1 – attack)
u[31:28], 1–A[27:24], 1–A[23:16], 1–A[15:8], 1–A[7:0]
0x00, 0x7F, 0x77, 0xC0
Channel 8 DRC2 decay
u[31:28], D[27:24], D[23:16], D[15:8], D[7:0]
0x00, 0x00, 0x00, 0x56
Channel 8 DRC2 (1 – decay)
u[31:28], 1–D[27:24], 1–D[23:16], 1–D[15:8], 1–D[7:0]
0x00, 0x3F, 0xFF, 0xA8
7.25 DRC Bypass Registers (0xA2–0xA9)
DRC bypass/inline for channels 1, 2, 3, 4, 5, 6, 7, and 8 are mapped into registers 0xA2, 0xA3, 0xA4,
0xA5, 0xA6, 0xA7, 0xA8, and 0xA9, respectively. Eight bytes are written for each channel. Each gain
coefficient is in 28-bit (5.23) format, so 0x0080 0000 is a gain of 1. Each gain coefficient is written as a
32-bit word with the upper 4 bits not used.
To enable DRC for a given channel (with unity gain), bypass = 0x0000 0000 and inline = 0x0080 0000.
To disable DRC for a given channel, bypass = 0x0080 0000 and inline = 0x0000 0000.
Table 7-26. DRC Bypass Register Format
REGISTER NAME
Channel bass DRC bypass
Channel DRC inline
TOTAL
BYTES
8
CONTENTS
INITIALIZATION VALUE
u[31:28], bypass[27:24], bypass[23:16], bypass[15:8], bypass[7:0]
0x00, 0x80, 0x00, 0x00
u[31:28], inline[27:24], inline[23:16], inline[15:8], inline[7:0]
0x00, 0x00, 0x00, 0x00
7.26 8×2 Output Mixer Registers (0xAA–0xAF)
Output mixers for channels 1–6 map to registers 0xAA–0xAF.
Total data per register is 8 bytes.
88
Serial-Control Interface Register Definitions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
Table 7-27. Output Mixer Register Format (Upper 4 Bytes)
D31
D30
D29
D28
D27
D26
D25
D24
FUNCTION
0
0
0
0
Select channel 1 to output mixer
0
0
0
1
Select channel 2 to output mixer
0
0
1
0
Select channel 3 to output mixer
0
0
1
1
Select channel 4 to output mixer
0
1
0
0
Select channel 5 to output mixer
0
1
0
1
Select channel 6 to output mixer
0
1
1
0
Select channel 7 to output mixer
0
1
1
1
Select channel 8 to output mixer
G27
G26
G25
G24
D23
D22
D21
D20
D19
D18
D17
D16
G23
G22
G21
G20
G19
G18
G17
G16
D15
D14
D13
D12
D11
D10
D9
D8
G15
G14
G13
G12
G11
G10
G9
G8
D7
D6
D5
D4
D3
D2
D1
D0
G7
G6
G5
G4
G3
G2
G1
G0
Selected channel gain (upper 4 bits)
FUNCTION
Selected channel gain (continued)
FUNCTION
Selected channel gain (continued)
FUNCTION
Selected channel gain (lower 8 bits)
Table 7-28. Output Mixer Register Format (Lower 4 Bytes)
D31
D30
D29
D28
D27
D26
D25
D24
FUNCTION
0
0
0
0
Select channel 1 to output mixer
0
0
0
1
Select channel 2 to output mixer
0
0
1
0
Select channel 3 to output mixer
0
0
1
1
Select channel 4 to output mixer
0
1
0
0
Select channel 5 to output mixer
0
1
0
1
Select channel 6 to output mixer
0
1
1
0
Select channel 7 to output mixer
0
1
1
1
Select channel 8 to output mixer
G27
G26
G25
G24
D23
D22
D21
D20
D19
D18
D17
D16
G23
G22
G21
G20
G19
G18
G17
G16
D15
D14
D13
D12
D11
D10
D9
D8
G15
G14
G13
G12
G11
G10
G9
G8
D7
D6
D5
D4
D3
D2
D1
D0
G7
G6
G5
G4
G3
G2
G1
G0
Selected channel gain (upper 4 bits)
FUNCTION
Selected channel gain (continued)
FUNCTION
Selected channel gain (continued)
FUNCTION
Selected channel gain (lower 8 bits)
7.27 8×3 Output Mixer Registers (0xB0–0xB1)
Output mixers for channels 7 and 8 map to registers 0xB0 and 0xB1, respectively.
Total data per register is 12 bytes.
Serial-Control Interface Register Definitions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
89
TAS5508C
SLES257 – SEPTEMBER 2010
www.ti.com
Table 7-29. Output Mixer Register Format (Upper 4 Bytes)
D31
D30
D29
D28
D27
D26
D25
D24
FUNCTION
0
0
0
0
Select channel 1 to output mixer
0
0
0
1
Select channel 2 to output mixer
0
0
1
0
Select channel 3 to output mixer
0
0
1
1
Select channel 4 to output mixer
0
1
0
0
Select channel 5 to output mixer
0
1
0
1
Select channel 6 to output mixer
0
1
1
0
Select channel 7 to output mixer
0
1
1
1
Select channel 8 to output mixer
G27
G26
G25
G24
D23
D22
D21
D20
D19
D18
D17
D16
G23
G22
G21
G20
G19
G18
G17
G16
D15
D14
D13
D12
D11
D10
D9
D8
G15
G14
G13
G12
G11
G10
G9
G8
D7
D6
D5
D4
D3
D2
D1
D0
G7
G6
G5
G4
G3
G2
G1
G0
Selected channel gain (upper 4 bits)
FUNCTION
Selected channel gain (continued)
FUNCTION
Selected channel gain (continued)
FUNCTION
Selected channel gain (lower 8 bits)
Table 7-30. Output Mixer Register Format (Middle 4 Bytes)
D31
D30
D29
D28
D27
D26
D25
D24
FUNCTION
0
0
0
0
Select channel 1 to output mixer
0
0
0
1
Select channel 2 to output mixer
0
0
1
0
Select channel 3 to output mixer
0
0
1
1
Select channel 4 to output mixer
0
1
0
0
Select channel 5 to output mixer
0
1
0
1
Select channel 6 to output mixer
0
1
1
0
Select channel 7 to output mixer
0
1
1
1
Select channel 8 to output mixer
G27
G26
G25
G24
D23
D22
D21
D20
D19
D18
D17
D16
G23
G22
G21
G20
G19
G18
G17
G16
D15
D14
D13
D12
D11
D10
D9
D8
G15
G14
G13
G12
G11
G10
G9
G8
D7
D6
D5
D4
D3
D2
D1
D0
G7
G6
G5
G4
G3
G2
G1
G0
Selected channel gain (upper 4 bits)
FUNCTION
Selected channel gain (continued)
FUNCTION
Selected channel gain (continued)
FUNCTION
Selected channel gain (lower 8 bits)
Table 7-31. Output Mixer Register Format (Lower 4 Bytes)
D31
D30
D29
D28
0
0
0
0
Select channel 1 to output mixer
0
0
0
1
Select channel 2 to output mixer
0
0
1
0
Select channel 3 to output mixer
0
0
1
1
Select channel 4 to output mixer
90
D27
D26
D25
D24
FUNCTION
Serial-Control Interface Register Definitions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
Table 7-31. Output Mixer Register Format (Lower 4 Bytes) (continued)
D31
D30
D29
D28
0
1
0
0
D27
D26
D25
D24
Select channel 5 to output mixer
0
1
0
1
Select channel 6 to output mixer
0
1
1
0
Select channel 7 to output mixer
0
1
1
1
Select channel 8 to output mixer
G27
G26
G25
G24
D23
D22
D21
D20
D19
D18
D17
D16
G23
G22
G21
G20
G19
G18
G17
G16
D15
D14
D13
D12
D11
D10
D9
D8
G15
G14
G13
G12
G11
G10
G9
G8
D7
D6
D5
D4
D3
D2
D1
D0
G7
G6
G5
G4
G3
G2
G1
G0
FUNCTION
Selected channel gain (upper 4 bits)
FUNCTION
Selected channel gain (continued)
FUNCTION
Selected channel gain (continued)
FUNCTION
Selected channel gain (lower 8 bits)
7.28 Volume Biquad Register (0xCF)
Each gain coefficient is in 28-bit (5.23) format so 0x80 0000 is a gain of 1. Each gain coefficient is written
as a 32-bit word with the upper four bits not used.
Table 7-32. Volume Biquad Register Format (Default = All-Pass)
DESCRIPTION
REGISTER FIELD CONTENTS
DEFAULT GAIN COEFFICIENT VALUES
DECIMAL
HEX
bo coefficient
u[31:28], b0[27:24], b0[23:16], b0[15:8], b0[7:0]
1.0
0x00, 0x80, 0x00, 0x00
b1 coefficient
u[31:28], b1[27:24], b1[23:16], b1[15:8], b1[7:0]
0.0
0x00, 0x00, 0x00, 0x00
b2 coefficient
u[31:28], b2[27:24], b2[23:16], b2[15:8], b2[7:0]
0.0
0x00, 0x00, 0x00, 0x00
a1 coefficient
u[31:28], a1[27:24], a1[23:16], a1[15:8], a1[7:0]
0.0
0x00, 0x00, 0x00, 0x00
a2 coefficient
u[31:28], a2[27:24], a2[23:16], a2[15:8], a2[7:0]
0.0
0x00, 0x00, 0x00, 0x00
Serial-Control Interface Register Definitions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
91
TAS5508C
SLES257 – SEPTEMBER 2010
www.ti.com
7.29 Volume, Treble, and Bass Slew Rates Register (0xD0)
Table 7-33. Volume Gain Update Rate (Slew Rate)
D31–D10
D9
D8
0
0
0
512-step update at 4 Fs, 42.6 ms at 48 kHz
FUNCTION
0
0
1
1024-step update at 4 Fs, 85.3 ms at 48 kHz
0
1
0
2048-step update at 4 Fs, 170 ms at 48 kHz
0
1
1
2048-step update at 4 Fs, 170 ms at 48 kHz
Table 7-34. Treble and Bass Gain Step Size (Slew Rate)
D7
D6
D5
D4
D3
D2
D1
D0
0
0
0
0
0
0
0
0
FUNCTION
0
0
0
0
0
0
1
1
0
0
0
0
0
1
0
0
Minimum rate – Updates every 0.083 ms (every LRCLK at 48 kHz)
0
0
1
0
0
0
0
0
Updates every 0.67 ms (32 LRCLKs at 48 kHz)
0
0
1
1
1
1
1
1
Default rate - Updates every 1.31 ms (63 LRCLKs at 48 kHz). This is the
maximum constant time that can be set for all sample rates.
1
1
1
1
1
1
1
1
Maximum rate – Updates every 5.08 ms (every 255 LRCLKs at 48 kHz)
No operation
7.30 Volume Registers (0xD1–0xD9)
Channels 1, 2, 3, 4, 5, 6, 7, and 8 are mapped into registers 0xD1, 0xD2, 0xD3, 0xD4, 0xD5, 0xD6, 0xD7,
and 0xD8, respectively. The default volume for all channels is 0 dB.
Master volume is mapped into register 0xD9. The default for the master volume is mute.
Bits D31–D12 are Don't Care.
Table 7-35. Volume Register Format
D31
D30
D29
D28
D27
D26
D25
D24
FUNCTION
Unused bits
D23
D22
D21
D20
D19
D18
D17
D16
FUNCTION
Unused bits
D15
92
D14
D13
D12
D11
D10
D9
D8
V11
V10
V9
V8
D7
D6
D5
D4
D3
D2
D1
D0
V7
V6
V5
V4
V3
V2
V1
V0
FUNCTION
Volume
FUNCTION
Volume
Serial-Control Interface Register Definitions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
Table 7-36. Master and Individual Volume Controls
VOLUME INDEX (H)
GAIN/INDEX
EXPECTED
ACTUAL
001
17.75
17.81
17.81
002
17.5
17.56
17.56
003
17.25
17.31
17.31
004
17
17.06
17.06
005
16.75
16.81
16.81
006
16.5
16.56
16.56
007
16.25
16.31
16.31
008
16
16.05
16.05
009
15.75
15.8
15.8
00A
15.5
15.55
15.55
00B
15.25
15.3
15.3
00C
15
15.05
15.05
00D
14.75
14.8
14.8
00E
14.5
14.55
14.55
00F
14.25
14.3
14.3
010
14
14.05
14.05
TO
044
1
1
1
045
0.75
0.75
0.75
046
0.5
0.5
0.5
047
0.25
0.25
0.25
048
0
0
0
049
–0.25
–0.25
–0.25
04A
–0.5
–0.5
–0.5
04B
–0.75
–0.75
–0.75
04C
–1
–1
–1
TO
240
–126
–126.43
–126.43
241
–126.25
–126.68
–126.99
242
–126.5
–126.93
–126.99
243
–126.75
–127.19
–127.59
244
–127
–127.44
–127.59
245
Mute
Mute
Mute
Mute
Mute
TO
3FF
Mute
Serial-Control Interface Register Definitions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
93
TAS5508C
SLES257 – SEPTEMBER 2010
www.ti.com
7.31 Bass Filter Set Register (0xDA)
Bits D31-D27, D23-D19, D15-D11, and D7-D3 are Don't Care.
Table 7-37. Channel 8 (Subwoofer)
D31
D30
D29
D28
D27
D26
D25
D24
0
0
0
0
0
0
0
0
No change
FUNCTION
0
0
0
0
0
0
0
1
Bass filter set 1
0
0
0
0
0
0
1
0
Bass filter set 2
0
0
0
0
0
1
1
1
Bass filter set 3
0
0
0
0
0
1
0
0
Bass filter set 4
0
0
0
0
0
1
0
1
Bass filter set 5
0
0
0
0
0
1
1
0
Reserved
0
0
0
0
0
1
1
1
Reserved
Table 7-38. Channels 6 and 5 (Right and Left Lineout in 6-Channel Configuration; Right and Left
Surround in 8-Channel Configuration)
D23
D22
D21
D20
D19
D18
D17
D16
0
0
0
0
0
0
0
0
No change
FUNCTION
0
0
0
0
0
0
0
1
Bass filter set 1
0
0
0
0
0
0
1
0
Bass filter set 2
0
0
0
0
0
1
1
1
Bass filter set 3
0
0
0
0
0
1
0
0
Bass filter set 4
0
0
0
0
0
1
0
1
Bass filter set 5
0
0
0
0
0
1
1
0
Reserved
0
0
0
0
0
1
1
1
Reserved
Table 7-39. Channels 4 and 3 (Right and Left Rear)
D15
D14
D13
D12
D11
D10
D9
D8
0
0
0
0
0
0
0
0
No change
0
0
0
0
0
0
0
1
Bass filter set 1
0
0
0
0
0
0
1
0
Bass filter set 2
0
0
0
0
0
1
1
1
Bass filter set 3
0
0
0
0
0
1
0
0
Bass filter set 4
0
0
0
0
0
1
0
1
Bass filter set 5
0
0
0
0
0
1
1
0
Reserved
0
0
0
0
0
1
1
1
Reserved
94
FUNCTION
Serial-Control Interface Register Definitions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
Table 7-40. Channels 7, 2, and 1 (Center, Right Front, and Left Front)
D7
D6
D5
D4
D3
D2
D1
D0
FUNCTION
0
0
0
0
0
0
0
0
No change
0
0
0
0
0
0
0
1
Bass filter set 1
0
0
0
0
0
0
1
0
Bass filter set 2
0
0
0
0
0
1
1
1
Bass filter set 3
0
0
0
0
0
1
0
0
Bass filter set 4
0
0
0
0
0
1
0
1
Bass filter set 5
0
0
0
0
0
1
1
0
Reserved
0
0
0
0
0
1
1
1
Reserved
7.32 Bass Filter Index Register (0xDB)
Index values above 0x24 are invalid.
Table 7-41. Bass Filter Index Register Format
I2C
SUBADDRESS
TOTAL
BYTES
REGISTER
NAME
0xDB
4
Bass filter index
(BFI)
DESCRIPTION OF CONTENTS
DEFAULT STATE
Ch8_BFI[31:24], Ch65_BFI[23:16], Ch43_BFI[15:8],
Ch721_BFI[7:0]
0x12, 0x12, 0x12, 0x12
Table 7-42. Bass Filter Indexes
BASS INDEX VALUE
ADJUSTMENT (dB)
BASS INDEX VALUE
ADJUSTMENT (dB)
0x00
18
0x13
–1
0x01
17
0x14
–2
0x02
16
0x15
–3
0x03
15
0x16
–4
0x04
14
0x17
–5
0x05
13
0x18
–6
0x06
12
0x19
–7
0x07
11
0x1A
–8
0x08
10
0x1B
–9
0x09
9
0x1C
–10
0x0A
8
0x1D
–11
0x0B
7
0x1E
–12
0x0C
6
0x1F
–13
0x0D
5
0x20
–14
0x0E
4
0x21
–15
0x0F
3
0x22
–16
0x10
2
0x23
–17
0x11
1
0x24
–18
0x12
0
Serial-Control Interface Register Definitions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
95
TAS5508C
SLES257 – SEPTEMBER 2010
www.ti.com
7.33 Treble Filter Set Register (0xDC)
Bits D31–D27 are Don't Care.
Table 7-43. Channel 8 (Subwoofer)
D31
D30
D29
D28
D27
D26
D25
D24
0
0
0
0
0
0
0
0
No change
FUNCTION
0
0
0
0
0
0
0
1
Treble filter set 1
0
0
0
0
0
0
1
0
Treble filter set 2
0
0
0
0
0
1
1
1
Treble filter set 3
0
0
0
0
0
1
0
0
Treble filter set 4
0
0
0
0
0
1
0
1
Treble filter set 5
0
0
0
0
0
1
1
0
Reserved
0
0
0
0
0
1
1
1
Reserved
Bits D23–D19 are Don't Care.
Table 7-44. Channels 6 and 5 (Right and Left Lineout in 6-Channel Configuration; Right and Left
Surround in 8-Channel Configuration)
D23
D22
D21
D20
D19
D18
D17
D16
0
0
0
0
0
0
0
0
No change
FUNCTION
0
0
0
0
0
0
0
1
Treble filter set 1
0
0
0
0
0
0
1
0
Treble filter set 2
0
0
0
0
0
1
1
1
Treble filter set 3
0
0
0
0
0
1
0
0
Treble filter set 4
0
0
0
0
0
1
0
1
Treble filter set 5
0
0
0
0
0
1
1
0
Reserved
0
0
0
0
0
1
1
1
Reserved
Bits D15–D11 are Don't Care.
Table 7-45. Channels 4 and 3 (Right and Left Rear)
D15
D14
D13
D12
D11
D10
D9
D8
0
0
0
0
0
0
0
0
No change
FUNCTION
0
0
0
0
0
0
0
1
Treble filter set 1
0
0
0
0
0
0
1
0
Treble filter set 2
0
0
0
0
0
1
1
1
Treble filter set 3
0
0
0
0
0
1
0
0
Treble filter set 4
0
0
0
0
0
1
0
1
Treble filter set 5
0
0
0
0
0
1
1
0
Reserved
0
0
0
0
0
1
1
1
Reserved
Bits D7–D3 are Don't Care.
Table 7-46. Channels 7, 2, and 1 (Center, Right Front, and Left Front)
96
D7
D6
D5
D4
D3
D2
D1
D0
0
0
0
0
0
0
0
0
No change
FUNCTION
0
0
0
0
0
0
0
1
Treble filter set 1
0
0
0
0
0
0
1
0
Treble filter set 2
Serial-Control Interface Register Definitions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
Table 7-46. Channels 7, 2, and 1 (Center, Right Front, and Left Front) (continued)
D7
D6
D5
D4
D3
D2
D1
D0
0
0
0
0
0
1
1
1
Treble filter set 3
FUNCTION
0
0
0
0
0
1
0
0
Treble filter set 4
0
0
0
0
0
1
0
1
Treble filter set 5
0
0
0
0
0
1
1
0
Reserved
0
0
0
0
0
1
1
1
Reserved
7.34 Treble Filter Index (0xDD)
Index values above 0x24 are invalid.
Table 7-47. Treble Filter Index Register Format
I2C
SUBADDRESS
TOTAL BYTES
0xDD
4
REGISTER
NAME
DESCRIPTION OF CONTENTS
Treble filter index (TFI)
DEFAULT STATE
Ch8_TFI[31:24], Ch65_TFI[23:16],
Ch43_TFI[15:8], Ch721_TFI[7:0]
0x12, 0x12, 0x12, 0x12
Table 7-48. Treble Filter Indexes
TREBLE INDEX VALUE
ADJUSTMENT (dB)
TREBLE INDEX VALUE
ADJUSTMENT (dB)
0x00
18
0x13
–1
0x01
17
0x14
–2
0x02
16
0x15
–3
0x03
15
0x16
–4
0x04
14
0x17
–5
0x05
13
0x18
–6
0x\06
12
0x19
–7
0x07
11
0x1A
–8
0x08
10
0x1B
–9
0x09
9
0x1C
–10
0x0A
8
0x1D
–11
0x0B
7
0x1E
–12
0x0C
6
0x1F
–13
0x0D
5
0x20
–14
0x0E
4
0x21
–15
0x0F
3
0x22
–16
0x10
2
0x23
–17
0x11
1
0x24
–18
0x12
0
7.35 AM Mode Register (0xDE)
Bits D31–D21 are Don't Care.
Table 7-49. AM Mode Register Format
D31
D30
D29
D28
D27
D26
D25
D24
FUNCTION
Unused bits
Serial-Control Interface Register Definitions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
97
TAS5508C
SLES257 – SEPTEMBER 2010
www.ti.com
Table 7-49. AM Mode Register Format (continued)
D31
D30
D29
D28
D27
D26
D25
D24
FUNCTION
D23
D22
D21
D20
D19
D18
D17
D16
FUNCTION
0
–
–
–
–
AM mode disabled
1
–
–
–
–
AM mode enabled
–
0
0
–
–
Select sequence 1
–
0
1
–
–
Select sequence 2
–
1
0
–
–
Select sequence 3
–
1
1
–
–
Select sequence 4
–
–
–
0
–
IF frequency = 455 kHz
–
–
–
1
–
IF frequency = 262.5 kHz
–
–
–
–
0
Use BCD-tuned frequency
–
–
–
–
1
Use binary-tuned frequency
Table 7-50. AM Tuned Frequency Register in BCD Mode (Lower 2 Bytes of 0xDE)
D15
D14
D13
D12
D11
D10
D9
D8
0
0
0
B0
–
–
–
–
BCD frequency (1000s kHz)
FUNCTION
–
–
–
–
B3
B2
B1
B0
BCD frequency (100s kHz)
0
0
0
0
0
0
0
0
D7
D6
D5
D4
D3
D2
D1
D0
B3
B2
B1
B0
–
–
–
–
BCD frequency (10s kHz)
–
–
–
–
B3
B2
B1
B0
BCD frequency (1s kHz)
0
0
0
0
0
0
0
0
Default value
FUNCTION
Default value
Table 7-51. AM Tuned Frequency Register in Binary Mode (Lower 2 Bytes of 0xDE)
D15
D14
D13
D12
D11
D10
D9
D8
0
0
0
0
0
B10
B9
B8
0
0
0
0
0
0
0
0
D7
D6
D5
D4
D3
D2
D1
D0
B7
B6
B5
B4
B3
B2
B1
B0
0
0
0
0
0
0
0
0
98
FUNCTION
Binary frequency (upper 3 bits)
Default value
FUNCTION
Binary frequency (lower 8 bits)
Default value
Serial-Control Interface Register Definitions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
SLES257 – SEPTEMBER 2010
7.36 PSVC Range Register (0xDF)
Bits D31–D2 are zero.
Table 7-52. PSVC Range Register Format
D31–D2
D1
D0
0
0
0
12.04-dB control range for PSVC
FUNCTION
0
0
1
18.06-dB control range for PSVC
0
1
0
24.08-dB control range for PSVC
0
1
1
Ignore – retain last value
7.37 General Control Register (0xE0)
Bits D31–D4 are zero. Bit D0 is Don't Care.
Table 7-53. General Control Register Format
D31–D4
D2
D1
0
D3
–
0
D0
8-channel configuration
FUNCTION
0
–
1
6-channel configuration
0
0
–
Power-supply volume control disabled
0
1
–
Power-supply volume control enabled
0
0
–
–
Subwoofer part of PSVC
0
1
–
–
Subwoofer separate from PSVC
7.38 Incremental Multiple-Write Append Register (0xFE)
This is a special register used to append data to a previously opened register.
Serial-Control Interface Register Definitions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
99
TAS5508C
SLES257 – SEPTEMBER 2010
100
www.ti.com
Serial-Control Interface Register Definitions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
TAS5508C
www.ti.com
8
SLES257 – SEPTEMBER 2010
TAS5508C Example Application Schematic
The following page contains an example application schematic for the TAS5508C.
TAS5508C Example Application Schematic
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TAS5508C
101
5
4
3
2
1
V-HBRIDGE
+3.3V +5.0V
/SD2_TAS5121
Left + Right Line Out
/LINE_OUT_ENABLE
/OTW_TAS5121
/SD1_TAS5121
GVDD
V-HBRIDGE
/TEMP_WARNING
GVDD
+5.0V
PWM_P_R
PWM_P
+3.3V
PWM_M_R
Phono socket
J950
LINE OUTPUT
4
3
2
1
/OE
OUT_R
/VALID
OUT_1
1
OUT_2
2
J600
PWM_M_L
RIGHT BACK
SURROUND
SPEAKER
OUTPUT
CH6 TAS5121 H-Bridge Output Stage
PWM_P_L
Phono socket
J951
D
PWM_M
/VALID_CH5+CH6
4
3
2
1
V-HBRIDGE
OUT_L
/SD2_TAS5121
2 Channel Line Out (TLV272)
/OTW_TAS5121
GND
+5.0V
Left + Right Headphone
/SHUTDOWN_TAS5121
/TEMP_WARNING
GVDD
PWM_P
PWM_M
+5.0V
R20 +3.3V
22.0R
1
2
J900
OUT_R
PWM_HPM_R
OUT_GND
PWM_HPP_R
Mini-Jack (3.5mm)
OUT_L
C25
220nF
OUT_2
2
C26
10uF
2
4
3
2
1
HEADPHONE OUTPUT
1
J500
LEFT BACK
SURROUND
SPEAKER
OUTPUT
V-HBRIDGE
2
PWM_HPP_L
/VALID
OUT_1
CH5 TAS5121 H-Bridge Output Stage
1
1
PWM_HPM_L
/VALID_CH5+CH6
D
GVDD
V-HBRIDGE
/SD2_TAS5121
/OTW_TAS5121
GND
2 Channel Headphone Design (TPA112)
/SHUTDOWN_TAS5121
GVDD
V-HBRIDGE
/TEMP_WARNING
GVDD
PWM_P
/VALID
PWM_M
OUT_1
1
/VALID
OUT_2
2
SUBWOOFER
SPEAKER
OUTPUT
J800
CH8 TAS5121 H-Bridge Output Stage
V-HBRIDGE
/SD1_TAS5121
/OTW_TAS5121
C
MCLK
/RESET_5518
1
/OTW_TAS5121
47
PWM_P
PLL_FLTM
PWM_M_4
46
PWM_M
OUT_1
1
4
PLL_FLTP
PWM_P_3
45
/VALID
OUT_2
2
5
AVSS
PWM_M_3
44
6
AVSS
PWM_P_2
43
7
VRD_PLL
PWM_M_2
42
8
AVSS_PLL
PWM_P_1
41
/SD2_TAS5121
9
AVDD_PLL
PWM_M_1
40
/OTW_TAS5121
TAS5508
10
VBGAP
VAILD
39
11
RESET
DVSS
38
BKND_ERR
37
DVDD
36
/PDN
13
PDN
14
MUTE
DVSS
35
15
DVDD
DVSS
34
16
DVSS
VR_DIG
33
/VALID
J400
V-HBRIDGE
/BKND_ERR
+3.3V
/VALID
/TEMP_WARNING
GVDD
PWM_M
OUT_1
1
/VALID
OUT_2
2
1
J300
LEFT
SURROUND
SPEAKER
OUTPUT
B
CH3 TAS5121 H-Bridge Output Stage
R18
1R
C23
10uF
1
/SD1_TAS5121
C24
100nF
2
C22
470nF
/OTW_TAS5121
/SHUTDOWN_TAS5121
GVDD
V-HBRIDGE
/TEMP_WARNING
GVDD
2
1
2
V-HBRIDGE
2
PSVC
GVDD
V-HBRIDGE
PWM_P
PWM_P
32
SDIN1
31
SDIN2
30
SDIN3
29
SDIN4
28
SCLK
27
LRCLK
26
SCL
25
SDA
24
RESERVED
23
RESERVED
22
RESERVED
21
XTL_IN
20
19
XTL_OUT
OSC_CAP
VR_DPLL
18
17
/SHUTDOWN_TAS5121
/VALID
/VALID
GND
1
1
RIGHT
SURROUND
SPEAKER
OUTPUT
CH4 TAS5121 H-Bridge Output Stage
1
PWM_M
OUT_1
1
/VALID
OUT_2
2
RIGHT
SPEAKER
OUTPUT
J200
C21
100nF
2
CH2 TAS5121 H-Bridge Output Stage
V-HBRIDGE
2
1
GVDD
GVDD
3
+3.3V
+5.0V +3.3V
/TEMP_WARNING
48
U1
CENTER
SPEAKER
OUTPUT
V-HBRIDGE
VR_PWM
/MUTE
2
GVDD
/SHUTDOWN_TAS5121
PWM_P_4
R14
1R
V-HBRIDGE
2
PLL_FLT_RET
HP_SEL
C20
100nF
OUT_2
VRA_PLL
/HP_SEL
C19
10uF
/VALID
2
2
GND
1
1
12
1
R13
3.30R
OUT_1
V-HBRIDGE
/SD2_TAS5121
1
B
C
PWM_M
2
50
51
52
53
54
55
56
57
58
59
60
61
62
49
PWM_M_7
PWM_P_7
PWM_M_8
PWM_P_8
DVSS_PWM
DVDD_PWM
PWM_M_5
PWM_P_5
PWM_M_6
PWM_P_6
PWM_HPML
PWM_HPPL
PWM_HPMR
63
PWM_HPPR
MCLK
64
C18
1nF
2
2
2
C17
100nF
GVDD
J700
1
1
1
1
2
C16
10uF
RESERVED
1
2
2
2
2
C12
100nF
/TEMP_WARNING
CH7 TAS5121 H-Bridge Output Stage
C29
100nF
2
2
C14
100nF
R12
2R
1
C15
100nF
C13
10nF
12
12
R11
200R
C11
100nF
+3.3V
1
1
1
1
2
R10
200R
GVDD
V-HBRIDGE
PWM_P
/VALID
C10
10nF
/SHUTDOWN_TAS5121
GND
/SD1_TAS5121
GND
PSVC
/OTW_TAS5121
/SHUTDOWN_TAS5121
GVDD
V-HBRIDGE
/TEMP_WARNING
GVDD
/RESET_5518
/RESET
SDIN3
/VALID
/BKND_ERR
/BKND_ERR
13.5MHz
/BKND_ERR
/BKND_ERR
2
PSVC
/SD1_TAS5121
PSVC
/SD1
/SD2_TAS5121
CONF_SEL
/VALID
/VALID_CH5+CH6
/LINE_OUT_ENABLE
CONF_SEL
/SD2
C27
15pF
/SD1_TAS5121
/SD1
SDIN4
C28
15pF
/LINE_OUT_ENABLE
/OTW_TAS5121
/OTW
1
OUT_2
2
J100
SDA
A
/SD2_TAS5121
/SD2
TAS5508 Example Application Schematic
/OTW_TAS5121
(Circuit is Subject To Change Without Notice)
/OTW
PSU and Interface Logic
5
LEFT
SPEAKER
OUTPUT
SCL
/VALID
/VALID_CH5+CH6
OUT_1
/VALID
LRCLK
2
R21
1M
PWM_M
CH1 TAS5121 H-Bridge Output Stage
SCLK
1
1
A
PSVC_MCPU
1
PSVC_MCPU
PWM_P
SDIN2
X10
/RESET_5518
2
+3.3V
+5.0V
GVDD
V-HBRIDGE
SDIN1
/RESET
4
3
2
1
PACKAGE OPTION ADDENDUM
www.ti.com
23-Sep-2010
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
Samples
(Requires Login)
TAS5508CPAG
ACTIVE
TQFP
PAG
64
160
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-4-260C-72 HR
Purchase Samples
TAS5508CPAGR
ACTIVE
TQFP
PAG
64
1500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-4-260C-72 HR
Purchase Samples
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
21-Sep-2010
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
TAS5508CPAGR
Package Package Pins
Type Drawing
TQFP
PAG
64
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
1500
330.0
24.4
Pack Materials-Page 1
13.0
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
13.0
1.5
16.0
24.0
Q2
PACKAGE MATERIALS INFORMATION
www.ti.com
21-Sep-2010
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TAS5508CPAGR
TQFP
PAG
64
1500
346.0
346.0
41.0
Pack Materials-Page 2
MECHANICAL DATA
MTQF006A – JANUARY 1995 – REVISED DECEMBER 1996
PAG (S-PQFP-G64)
PLASTIC QUAD FLATPACK
0,27
0,17
0,50
48
0,08 M
33
49
32
64
17
0,13 NOM
1
16
7,50 TYP
Gage Plane
10,20
SQ
9,80
12,20
SQ
11,80
0,25
0,05 MIN
1,05
0,95
0°– 7°
0,75
0,45
Seating Plane
0,08
1,20 MAX
4040282 / C 11/96
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-026
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DLP® Products
www.dlp.com
Communications and
Telecom
www.ti.com/communications
DSP
dsp.ti.com
Computers and
Peripherals
www.ti.com/computers
Clocks and Timers
www.ti.com/clocks
Consumer Electronics
www.ti.com/consumer-apps
Interface
interface.ti.com
Energy
www.ti.com/energy
Logic
logic.ti.com
Industrial
www.ti.com/industrial
Power Mgmt
power.ti.com
Medical
www.ti.com/medical
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Space, Avionics &
Defense
www.ti.com/space-avionics-defense
RF/IF and ZigBee® Solutions www.ti.com/lprf
Video and Imaging
www.ti.com/video
Wireless
www.ti.com/wireless-apps
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2010, Texas Instruments Incorporated