MITEL MT9042

MT9042

Global Digital Trunk Synchronizer
Preliminary Information
Features
ISSUE 1
June 1994
Ordering Information
•
Provides T1 and E1 clocks, and ST-BUS/GCI
framing signals locked to an input reference of
either 8 kHz (frame pulse), 1.544 MHz (T1), or
2.048 MHz (E1)
•
Meets AT & T TR62411 and ETSI ETS 300 011
specifications for a 1.544 MHz (T1), or
2.048 MHz (E1) input reference
•
Provides Time Interval Error (TIE) correction to
suppress input reference rearrangement
transients
•
Typical unfiltered intrinsic output jitter is
0.013 UI peak-to-peak
•
Jitter attenuation of 15 dB @ 10 Hz,
34 dB @ 100 Hz and 50 dB @ 5 to 40 kHz
•
Low power CMOS technology
Applications
•
Synchronization and timing control for T1 and
E1 digital transmission links
•
ST-BUS clock and frame pulse sources
•
Primary Trunk Rate Converters
VDD
VSS
MT9042AP
28 Pin PLCC
-40 °C to +85 °C
Description
The MT9042 is a digital phase-locked loop (PLL)
designed to provide timing and synchronization
signals for T1 and E1 primary rate transmission links
that are compatible with ST-BUS/GCI frame
alignment timing requirements. The PLL outputs can
be synchronized to either a 2.048 MHz, 1.544 MHz,
or 8 kHz reference. The T1 and E1 outputs are fully
compliant with AT & T TR62411 (ACCUNET® T1.5)
and ETSI ETS 300 011 intrinsic jitter and jitter
transfer
specifications,
respectively,
when
synchronized to primary reference input clock rates
of either 1.544 MHz or 2.048 MHz.
The PLL also provides additional high speed output
clocks at rates of 3.088 MHz, 4.096 MHz, 8.192
MHz, and 16.384 MHz for backplane synchronization.
TRST
MCLKo
MCLKi
RST
C3
C1.5
PRI
SEC
C16
Reference
Select
MUX
TIE
Corrector
PLL
Interface
Circuit
C8
C4
C2
F0o
FP8-STB
FP8-GCI
RSEL
Automatic State
Machine
LOSS1
Divider
LOSS2
GTo
GTi
MS1
MS2
FSEL1
FSEL2
Figure 1 - Functional Block Diagram
3-97
MT9042
4 3 2 1 28 27 26
5
25
24
6
7
23
22
8
21
9
10
20
19
11
12 13 14 15 16 17 18
RSEL
MS1
MS2
LOSS1
LOSS2
GTo
GTi
C3
C2
C4
VSS
C8
C16
VDD
VDD
MCLKo
MCLKi
FP8-GCI
F0o
FP8-STB
C1.5
TRST
VSS
RST
FSEL1
FSEL2
PRI
SEC
Preliminary Information
Figure 2 - Pin Connections
Pin Description
Pin #
Name
1
VSS
2
TRST
TIE Circuit Reset (TTL compatible). When HIGH, the time interval error correction circuit is
alternately establishing the phase difference between the PRI and SEC reference inputs,
depending upon which input is selected as input for PLL synchronization. This information is
used to generate a virtual reference for input to the PLL. When LOW, the time interval error
correction circuit is bypassed.
3
SEC
Secondary Reference Input (TTL compatible). This input (either 8 kHz, 1.544 MHz, or
2.048 MHz as controlled by the input frequency selection pins) is used as an alternate
reference source for PLL synchronization.
4
PRI
Primary Reference Input (TTL compatible). This input (either 8 kHz, 1.544 MHz, or 2.048
MHz as controlled by the input frequency selection pins) is used as the primary reference
source for PLL synchronization.
5
VDD
Positive Supply Voltage. Nominally +5 volts.
6
MCLKo
Master Clock Oscillator Output. This is a CMOS buffered output used for driving a 20 MHz
crystal.
7
MCLKi
Master Clock Oscillator Input. This is a CMOS input for a 20 MHz crystal or crystal
oscillator. Signals should be DC coupled to this pin.
8
9
10
Description
Negative Power Supply Voltage. Nominally 0 Volts.
FP8-GCI Frame Pulse Output (CMOS compatible). This is an 8 kHz output framing pulse that
indicates the start of the active GCI-BUS frame. The pulse width is based upon the period of
the 8.192 MHz synchronization clock.
F0o
Frame Pulse Output (CMOS compatible). This is an 8 kHz output framing pulse that
indicates the start of the active ST-BUS frame. The pulse width is based upon the period of
the 4.096 MHz synchronization clock. This is an active low signal.
FP8-STB Frame Pulse Output (CMOS compatible). This is an 8 kHz output framing pulse that
indicates the start of the active ST-BUS frame. The pulse width is based upon the period of
the 8.192 MHz synchronization clock.
11
C1.5
Clock 1.544 MHz (CMOS compatible). This ouput is a 1.544 MHz (T1) output clock locked
to the selected reference input signal.
12
C3
Clock 3.088 MHz (CMOS compatible). This output is a 3.088 MHz output clock locked to
the selected reference input signal.
3-98
MT9042
Preliminary Information
Pin Description (continued)
Pin #
Name
Description
13
C2
Clock 2.048 MHz (CMOS compatible). This output is a 2.048 MHz (E1) output clock
locked to the selected reference input signal.
14
C4
Clock 4.096 MHz (CMOS compatible). This output is a 4.096 MHz output clock locked to
the selected reference input signal.
15
VSS
Negative Power Supply Voltage. Nominally 0 Volts.
16
C8
Clock 8.192 MHz (CMOS compatible). This output is an 8.192 MHz output clock locked to
the selected reference input signal.
17
C16
Clock 16.384 MHz (CMOS compatible). This output is a 16.384 MHz output clock locked
to the selected reference input signal.
18
VDD
Positive Supply Voltage. Nominally +5 volts.
19
GTi
Guard Time Input (TTL Level Schmitt Trigger). This TTL level Schmitt trigger input is
used to determine the threshold level of the RC generated (guard) time constant. This
function filters out unwanted rearrangements between the PRI and SEC reference input
signals.
20
GTo
Guard Time Output (CMOS compatible). This is a CMOS buffered output used to drive the
external RC generated (guard) time constant circuit.
21
LOSS2
Reference Loss Indicator - 2 Input (TTL compatible). This input, in conjunction with
LOSS1, comprises a set of signals which control the event driven state machine when the
PLL is operating in AUTOMATIC mode (see Table 4).
22
LOSS1
Reference Loss Indicator - 1 Input (TTL compatible). This input, in conjunction with
LOSS2, comprises a set of signals which control the event driven state machine when the
PLL is operating in AUTOMATIC mode (see Table 4).
23
MS2
Mode Select - 2 Input (TTL compatible). This input, in conjunction with MS1, selects the
PLL mode of operation (i.e.,NORMAL, HOLDOVER, FREERUN, or AUTOMATIC; see Table
1).
24
MS1
Mode Select - 1 Input (TTL compatible). This input, in conjunction with MS2, selects the
PLL mode of operation (i.e., NORMAL, HOLDOVER, FREERUN, or AUTOMATIC; see Table
1).
25
RSEL
Input Reference Select (TTL compatible). When LOW this input selects PRI as the
reference input signal, and when HIGH, selects SEC as the reference input signal (see Table
2).
26
FSEL2
Frequency Select - 2 Input (TTL compatible). This input, in conjunction with FSEL1,
selects the frequency of the input reference source (i.e., 8 kHz, 1.544 MHz, or 2.048 MHz;
see Table 3).
27
FSEL1
Frequency Select - 1 Input (TTL compatible). This input, in conjunction with FSEL2,
selects the frequency of the input reference source (i.e., 8 kHz, 1.544 MHz, or 2.048 MHz;
see Table 3).
28
RST
Reset (TTL compatible). This input (active LOW) puts the MT9042 in its reset state. To
guarantee proper operation, the device must be reset after power-up. The time constant for
a power-up reset circuit must be a minimum of five times the rise time of the power supply. In
normal operation, the RST pin must be held low for a minimum of 60 nsec to reset the
device.
3-99
MT9042
Preliminary Information
Functional Description
Modes of Operation
The MT9042 is a fully digital, phase-locked loop
designed to provide timing references to interface
circuits for T1 and E1 Primary Rate Digital
Transmission links. As shown in Figure 1, the PLL
consists of an input reference selection circuit (MUX),
a Time Interval Error corrector (TIE), and a PLL that
employs a high resolution Digitally Controlled
Oscillator (DCO) to generate the T1 and E1 outputs.
The MT9042 can operate in one of two modes,
MANUAL or AUTOMATIC, as controlled by mode
select pins MS1 and MS2 (see Table 1). In MANUAL
mode, the user is responsible for switching
references during NORMAL operation, as well as
forcing the PLL into FREERUN or HOLDOVER
states.
The MT9042 accepts two reference clock inputs,
primary (PRI) and secondary (SEC) both connected
to independent external reference sources, either of
which can be selected as reference for
synchronization by the reference select (RSEL)
input. The selected reference signal is then
regenerated by the TIE correction circuit and passed
as a virtual reference to the PLL. The TIE correction
circuit will limit phase jumps (as specified by AT & T
TR62411 and ETSI ETS 300 011) during
rearrangement between the external reference
clocks. This virtual reference is then used by the
PLL for synchronizing the output signals.
The interface circuit on the output of the DCO
generates 1.544 MHz (C1.5), 3.088 MHz (C3), 2.048
MHz (C2), 4.096 MHz (C4), 8.192 MHz (C8), 16.384
MHz (C16), and three 8 kHz frame pulses F0o, FP8STB, and FP8-GCI.
fref
Phase
Detector
Loop
Filter
DCO
fsync
When AUTOMATIC mode is selected, operation is
controlled by an internal state machine. Under state
machine control, input reference selection is
automatically based upon the input levels of LOSS1
and LOSS2.
MS2
MS1
Description of Operation
0
0
NORMAL (manual mode)
0
1
HOLDOVER (manual mode)
1
0
FREERUN (manual mode)
1
1
AUTOMATIC MODE
Table 3- Operating Modes of the MT9042
Manual Mode
In MANUAL mode operation, the input reference
selection is accomplished through a 2-to-1
multiplexer, which is controlled by the RSEL input
pin. As shown in Table 2, for MANUAL mode
operation RSEL=0 selects PRI as the primary
reference input, while RSEL=1 selects SEC as the
primary reference input.
Mode
RSEL
Reference Input
Selected
Manual
0
PRI
Manual
1
SEC
Automatic
0
state machine control
Automatic
1
state machine control, but
treats SEC as primary
and PRI as secondary
Divider
Figure 3 - PLL Block Diagram
As shown in Figure 3, the PLL of the MT9042
consists of a phase detector (PD), a loop filter, a high
resolution DCO, and a digital frequency divider. The
digitally controlled oscillator (DCO) is locked in
frequency (n x fref) to one of three possible reference
frequencies, configured using pins FSEL1 and
FSEL2. Combined with the reference select input
RSEL, the PLL is capable of providing a full range of
E1/T1 clock signals synchronized to either the
primary PRI or secondary SEC input. The loop filter
is a first order lowpass structure that provides
approximately a 2 Hz bandwidth.
3-100
Table 4- Reference Input Selection of the MT9042
There are three possible input frequencies for
selection as the primary reference clock. These are 8
kHz, 1.544 MHz or 2.048 MHz. Frequency selection
is controlled by the logic levels of FSEL1 and FSEL2,
as shown in Table 3. This variety of input frequencies
was chosen to allow the generation of all the
necessary T1 and E1 clocks from either a T1, E1 or
frame pulse reference source.
MT9042
Preliminary Information
Automatic Mode
In normal AUTOMATIC mode operation, the RSEL
input is set to 0. This will allow the state machine to
control PLL operation and select the reference input
based on the state of the LOSS1 and LOSS2 inputs
(see state transitions in Table 4). If the PRI reference
signal is lost (LOSS1 = HIGH, LOSS2 = LOW), then
the PLL will enter HOLDOVER mode immediately
and stay there for a time determined by the RC time
constant connected to the Guard Time input (GTi,
GTo).
The state machine will continue to monitor the LOSS1
input and will switch back to the PRI reference once
the primary reference becomes functional as indicated
by the LOSS1 input. A logic level HIGH on both the
LOSS1 or LOSS2 inputs indicates that none of the
external references are available. Under these
circumstances, the PLL will be switched into the
HOLDOVER state (within a specified rate of frame
slip) until a fuIly functional reference input is available.
R (Ω)
GTo
GTi
C (f)
FSEL
2
FSEL
1
Input Reference Frequency
0
0
Reserved
0
1
8 kHz
1
0
1.544 MHz
1
1
2.048 MHz
Table 5 - Input Frequency Selection of the MT9042
(a)
Time Interval Error Correction Circuit
(TIE)
VGTi
1.77v
tgt
time
(b)
Figure 4 - a) RC circuit for guard time,
b) exponential waveform on GTi
When the primary reference signal has not been
regained and the guard time has been exceeded, the
reference will be switched to SEC. The time
constant determined by the RC circuit connected to
the GTi input provides the hysteresis on automatic
switching between PRI and SEC during very short
interruptions of the primary reference signal. The
Guard Time, tgt, can be predicted using the step
response of an RC network. The capacitor voltage
on the RC circuit is described by an exponential
curve. When the capacitor voltage reaches the
positive going threshold of GTi (typically 1.77 volts
for Schmitt trigger TTL inputs, see Figure 4) a logic
HIGH level results. This causes the state machine to
move from the holdover state of PRI to the state of
using SEC as the input reference. The following
equation can be used to determine the Guard Time
tgt:
t gt
 Vdd – 1.77 
-
= – RC ln  -----------------------Vdd 

The TIE correction circuit generates a virtual input
synchronized to the selected primary input
reference. After a reference rearrangement the TIE
corrects the phase of this new reference in such a
way that the virtual input preserves its phase. In
other words, reference switching will not create
significant phase changes on the virtual input, and
therefore, the outputs of the PLL.
The TIE reset (TRST) aligns the falling edge of the
current input with the falling edge of the primary
input reference. When TRST is held LOW for at least
100 ns, the next falling edge of the reference input
becomes aligned and passes through the TIE circuit
without additional delay.
PLL Measures of Performance
To meet the requirements of AT & T TR62411 and
ETSI 300 011, the following PLL performance
parameters were measured:
• locking range and lock time
•
slip rate in holdover mode
•
free-run accuracy
•
maximum time interval error and slope
•
intrinsic jitter
•
jitter transfer function
•
output jitter spectrum
•
wander
3-101
MT9042
Preliminary Information
Description
Freerun
Normal
(PRI)
Normal
(SEC)
Holdover
(PRI)
Holdover
(SEC)
State
P1
P2
P3
P4a
P4b
Power On (RST=0
LOSS1=X LOSS2=X)
No change
Invalid state
Invalid state
Invalid state
Invalid state
LOSS1=0 LOSS2=0
P2
No change
P2
P2
P2
LOSS1=1 LOSS2=0
time loss < tgt
P3
P4a
ST.GD
No change
No change
P3
LOSS1=1 LOSS2=0
time loss > tgt
P3
Invalid state
No change
P3
P3
LOSS1=0 LOSS2=1
P2
No change
P2
P2
P2
LOSS1=1 LOSS2=1
No change
P4a
P4b
No change
No change
Where : ST.GD = Start guard time; X = Don’t care
Table 4 - State Table For Automatic Input Reference Selection and Operating Mode
Locking Range and Lock Time
The locking range of the PLL is the range that the
input reference frequency can be deviated from its
nominal frequency while the output signals maintain
synchronization. The relevant value is usually
specified in parts-per-million (ppm). For both the T1
and E1 outputs, lock was maintained while an 8 kHz
input was varied between 7900 Hz to 8100 Hz
(corresponding to ±12500 ppm). This is well beyond
the required ±100 ppm. The lock range of 12500
ppm also applies to 1.544 MHz and 2.048 MHz
reference inputs.
The lock time is a measure of how long it takes the
PLL to reach steady state frequency after a
frequency step on the reference input signal. The
locking time is measured by applying an 8000 Hz
signal to the primary reference and an 8000.8 Hz
(+100 ppm) to the secondary reference. The output
is monitored with a time interval analyzer during slow
periodic rearrangements on the reference inputs.
The lock time for both the T1 and E1 outputs is
approximately 311 ms, which is well below the
required lock time of 1.0 seconds.
Holdover and Freerun Accuracy
The holdover option of the PLL provides the user
with the capability of maintaining the integrity of
output signals when the input reference signals are
lost. Holdover performance is defined as the rate of
3-102
slip (i.e., amount of slip on 60 seconds) of the 8 kHz
reference input. For both the T1 and E1 outputs the
rate of slip was measured as a function of the input
reference frequency. The results measured over an
observation period of 60 seconds, are presented in
Table 5.
Reference Input
Frequency
% of Frame Pulse Slip
8 kHz
8%
1.544 MHz
58%
2.048 Hz
58%
Table 5 - Holdover Slip Rate (60 seconds)
The freerun accuracy of the PLL is a measure of how
accurately the PLL can reproduce the desired output
frequency. The freerun accuracy is a function of
master clock frequency which must be 20 MHz ±32
ppm in order to meet AT & T TR62411 and ETSI
specifications.
Maximum Time Interval Error (MTIE)
MTIE is a measure of the rate of change of phase on
the output signal due to a step in phase on the
reference input. The specification also clearly
indicates a peak constraint on the characteristic of
the output signal. The specification is uniquely a
function of the loop bandwidth (or loop delay) of the
PLL. AT & T TR62411 clearly indicates that a
MT9042
Preliminary Information
maximum time interval error should not exceed 1µs.
As well, during this transient response, the output
signal shall not change its phase position in time
faster than 81 ns per 1.326 ms observation period.
jitter of the device, hence attention to minimization of
master clock jitter is required.
For the case where the PRI and SEC reference
inputs are both at 8 kHz, but phase separated by
180° the maximum time interval recorded for input
rearrangement is 320 ns. For a 45 degree separation
of the reference inputs, an 85 Hz periodic
rearrangement indicated a measured slope of 10ns
per 1.326 ms observation period.
The jitter transfer function is a measure of the
transfer characteristics of the PLL to frequency
specific jitter on the referenced input of the PLL. It is
directly linked to the loop bandwidth and the
magnitude of the phase error suppression
characteristics of the PLL. It is measured by applying
jitter of specific magnitude and frequencies to the
input of the PLL, then measuring the magnitude of
the output jitter (both filtered and unfiltered) on the
T1 or E1 output.
Jitter Transfer Function
Jitter Performance
The output jitter of a digital trunk PLL is composed of
intrinsic jitter, measured using a jitter free reference
clock, and frequency dependent jitter, measured by
applying known levels of jitter on the references
clock. The jitter spectrum indicates the frequency
content of the output jitter.
Care must be taken when measuring the transfer
characteristics to ensure that critical jitter alias
frequencies are included in the measurement (i.e.,
for digital phase locked loops using an 8 kHz input).
Tables 8 and 9 provide measured results for the jitter
transfer characteristics of the PLL for both a 1.544
MHz and 2.048 MHz reference input clock. The
transfer characteristics for an 8 kHz reference input
will be the same.
Intrinsic Jitter
Intrinsic jitter is the jitter added to an output signal by
the processing device, in this case the enhanced
PLL. Tables 6 and 7 show the average measured
intrinsic jitter of the T1 and E1 outputs. Each
measurement is an average based upon a ±100 ppm
deviation (in steps of 20 ppm) on the input reference
clock. Jitter on the master clock will increase intrinsic
Figures 5 and 6 show the jitter attenuation
performance of the T1 and E1 outputs plotted
against AT & T TR62411 and ETSI requirements,
respectively.
Output Jitter in UIp-p
Reference Input
FLT0 Unfiltered
FLT1
10Hz - 8kHz
FLT2
10Hz - 40kHz
FLT3
8kHz - 40kHz
8 kHz
.011
.004
.006
.002
1.544 MHz
.011
.001
.002
.001
2.048 MHz
.011
.001
.002
.001
Table 6 -Typical Intrinsic Jitter for the T1 Output
Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing .
Output Jitter in UIp-p
Reference Input
FLT0 Unfiltered
FLT1
20Hz - 100kHz
FLT2
700Hz - 100kHz
8 kHz
.011
.002
.002
1.544 MHz
.011
.002
.002
2.048 MHz
.011
.002
.002
Table 7 - Typical Intrinsic Jitter for the E1 Output
Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing .
3-103
MT9042
Preliminary Information
Measured Jitter Output (UIp-p)
Input Jitter
Modulation
Frequency
(Hz)
Input Jitter
Magnitude
(UIp-p)
10
T1 Reference Input
E1 Reference Input
Output Jitter
Magnitude
(UIp-p)
Jitter
Attenuation
(dB)
Output Jitter
Magnitude
(UIp-p)
Jitter
Attenuation
(dB)
20
2.42
18.34
2.41
18.38
20
20
1.62
21.83
1.618
21.84
40
20
.900
26.94
.908
26.86
100
20
.375
34.54
.376
34.52
330
10
.060
44.44
.060
44.44
500
8
.032
47.96
.032
47.96
1000
7
.015
53.38
.015
53.38
5000
0.8
.003
48.52
.003
48.52
7900
1.044
.003
50.83
.003
50.83
7950
1.044
.003
50.83
.003
50.83
7980
1.044
.003
50.83
.003
50.83
7999
1.044
.003
50.83
.003
50.83
8001
1.044
.003
50.83
.003
50.83
8020
1.044
.003
50.83
.003
50.83
8050
1.044
.003
50.83
.003
50.83
8100
1.044
.003
50.83
.003
50.83
10000
0.4
.003
42.50
.003
42.50
Table 8 - Typical Jitter Transfer Function for the T1 Output
Notes
1) For input jitter from 10 kHz to 100 kHz, the jitter attenuation is of such magnitude that intrinsic jitter dominates the output
signal, rendering the jitter transfer function unmeasurable.
2) Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing.
3-104
MT9042
Preliminary Information
Measured Jitter Output (UIp-p)
Input Jitter
Modulation
Frequency
(Hz)
Input Jitter
Magnitude
(UIp-p)
10
T1 Reference Input
E1 Reference Input
Output Jitter
Magnitude
(UIp-p)
Jitter
Attenuation
(dB)
Output Jitter
Magnitude
(UIp-p)
Jitter
Attenuation
(dB)
1.5
.355
12.52
.351
12.62
20
1.5
.186
18.13
.185
18.18
40
1.5
.095
23.97
.096
23.88
100
1.5
.039
31.70
.039
31.70
200
1.5
.021
37.08
.020
37.50
400
1.5
.012
41.94
.012
41.94
1000
1.5
.006
47.96
.007
46.62
7900*
1.044
.002
54.35
.002
54.35
7950*
1.044
.002
54.35
.002
54.35
7980*
1.044
.002
54.35
.002
54.35
7999*
1.044
.002
54.35
.002
54.35
8001*
1.044
.002
54.35
.002
54.35
8020*
1.044
.002
54.35
.002
54.35
8050*
1.044
.002
54.35
.002
54.35
8100*
1.044
.002
54.35
.002
54.35
10000
0.35
.004
38.84
.003
41.34
100000
0.20
.004
33.98
.003
36.48
Table 9 - Typical Jitter Transfer Function for the E1 Output
Notes
1) For input jitter from 10 kHz to 100 kHz, the jitter attenuation is of such magnitude that intrinsic jitter dominates the output
signal, rendering the jitter transfer function unmeasurable.
2) Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing.
* Output jitter dominated by intrinsic jitter.
3-105
MT9042
Preliminary Information
0
b)
a)
10
JITTER ATTENUATION (dB)
SLOPE -20 dB PER DECADE
20
30
SLOPE -40 dB
PER DECADE
40
50
60
1
10
20
100
300
1K
10K
Frequency (Hz)
Figure 5 - Typical Jitter Attenuation for T1 Output
JITTER ATTENUATION (dB)
dB
-0.5
0
19.5
AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
AAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
AAA
AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAA
AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
AAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAA
-20
dB/decade
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
AAA
AAAA
AAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAA
10
40
Frequency (Hz)
400
Figure 6 - Typical Jitter Attenuation for E1 Output
3-106
10K
MT9042
Preliminary Information
Absolute Maximum Ratings*- Voltages are with respect to ground (VSS) unless otherwise stated.
Parameter
Symbol
Min
Max
Units
VDD
-0.3
7.0
V
VI
VSS-0.3
VDD+0.3
V
IIK/OK
±150
mA
1
Supply Voltage
2
Voltage on any pin
3
Input/Output Diode Current
4
Output Source or Sink Current
IO
±150
mA
5
DC Supply or Ground Current
IDD/ISS
±300
mA
6
Storage Temperature
125
°C
7
Package Power Dissipation
900
mW
TST
PLCC
-55
PD
* Exceeding these values may cause permanent damage. Functional operation under these conditions is not implied.
Recommended Operating Conditions - Voltages are with respect to ground (VSS) unless otherwise stated.
Characteristics
Sym
Min
Typ‡
Max
Units
5.0
5.5
V
1
Supply Voltage
VDD
4.5
2
Input HIGH Voltage
VIH
2.0
VDD
V
3
Input LOW Voltage
VIL
VSS
0.8
V
4
Operating Temperature
TA
-40
85
°C
25
Test Conditions
‡ Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing.
DC Electrical Characteristics -
Voltages are with respect to ground (VSS) unless otherwise stated.
VDD =5.0 V±10%; VSS =0V; TA =-40 to 85°C.
Characteristics
1
2
3
4
5
6
S
U
P
I
N
O
U
T
Supply Current
Sym
Min
Typ‡
Max
55
IDD
2.0
Units
Test Conditions
mA
Under operating condition
Input HIGH voltage
VIH
V
Input LOW voltage
VIL
Output current HIGH
IOH
-4
mA
VOH=2.4 V
Output current LOW
IOL
4
mA
VOL=0.4 V
Leakage current on all inputs
IIL
µA
VIN=VSS
0.8
10
V
‡ Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing.
3-107
MT9042
Preliminary Information
AC Electrical Characteristics (see Fig. 7)†-Voltages are with respect to ground (VSS) unless otherwise stated.
Characteristics
Sym
Min
Typ‡
Max
Units
Test Conditions
1
8 kHz reference clock period
tP8R
125
µs
2
1.544 MHz reference clock period
tP15R
648
ns
3
2.048 MHz reference clock period
tP20R
488
ns
Input to output propagation delay
with an 8 kHz reference clock
tPD8
183
ns
MCLKi =
20.000 000MHz
Input to output propagation delay
with a 1.544 MHz reference clock
tPD15
243
ns
MCLKi =
20.000 000MHz
Input to output propagation delay
with a 2.048 MHz reference clock
tPD20
183
ns
MCLKi =
20.000 000MHz
4
5
6
I
N
P
U
T
S
7
Input rise time (except MCLKi and
GTi)
8
ns
8
Input fall time (except MCLKi and
GTi)
8
ns
9
Delay between C1.5 and C2
tD-20-15
18
ns
10
Frame pulse F0o output pulse
width
tW-F0o
244
ns
11
Frame pulse F0o output rise time
tR-F0o
5
9
ns
Load = 85pF
12
Frame pulse F0o output fall time
tF-F0o
5
9
ns
Load = 85pF
13
Frame pulse FP8-STB output
pulse width
tW-FP8STB
122
14
Frame pulse FP8-STB output rise
time
tR-FP8STB
5
9
ns
15
Frame pulse FP8-STB output fall
time
tF-FP8STB
5
9
ns
Frame pulse FP8-GCI output
pulse width
tW-FP8GCI
122
Frame pulse FP8-GCI output rise
time
tR-FP8GCI
5
9
ns
Frame pulse FP8-GCI output fall
time
tF-FP8GCI
5
9
ns
16
17
18
O
U
T
P
U
T
S
ns
Load = 85pF
Load = 85pF
ns
Load = 85pF
Load = 85pF
19
C1.5 clock period
tP-C1.5
648
20
C1.5 clock output rise time
tRC1.5
5
9
ns
Load = 85pF
21
C1.5 clock output fall time
tFC1.5
5
9
ns
Load = 85pF
22
C1.5 clock output duty cycle
23
C3 clock period
24
ns
50
%
tP-C3
324
ns
C3 clock output rise time
tRC3
5
9
ns
Load = 85pF
25
C3 clock output fall time
tFC3
5
9
ns
Load = 85pF
26
C3 clock output duty cycle
27
C2 clock period
28
C2 clock output rise time
3-108
50
%
tP-C2
488
ns
tRC2
5
9
ns
Load = 85pF
MT9042
Preliminary Information
AC Electrical Characteristics (see Fig. 7)†-Voltages are with respect to ground (VSS) unless otherwise stated.
Characteristics
29
C2 clock output fall time
30
C2 clock output duty cycle
31
C4 clock period
32
33
34
35
36
37
38
†
O
U
T
P
U
T
S
Sym
Min
tFC2
Typ‡
Max
Units
5
9
ns
Test Conditions
Load = 85pF
50
%
tP-C4
244
ns
C4 clock output rise time
tRC4
5
9
ns
Load = 85pF
C4 clock output fall time
tFC4
5
9
ns
Load = 85pF
C4 clock output duty cycle
50
%
ns
C8 clock period
tP-C8
122
C8 clock output rise time
tRC8
5
9
ns
Load = 85pF
C8 clock output fall time
tFC8
5
9
ns
Load = 85pF
C8 clock output duty cycle
50
%
ns
39
C16 clock period
tP-C16
61
40
C16 clock output rise time
tRC16
5
9
ns
Load = 85pF
41
C16 clock output fall time
tFC16
5
9
ns
Load = 85pF
42
C16 clock output duty cycle
50
55
%
Duty cycle on
MCLKi =50%
43
-Timing is over recommended temperature & power supply voltages.
figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing.
‡ -Typical
3-109
MT9042
Preliminary Information
tPD-8
PRI- 8 kHz
tPD-20
PRI-2.048 MHz
tW-F0o
F0o
tW-FP8STB
FP8-STB
tW-FP8GCI
FP8-GCI
tP-C16
C16
tP-C8
C8
tP-C4
C4
tP-C2
C2
tP-C3
tD-20-15
C3
C1.5
tPD-15
PRI-1.544 MHz
tP-C1.5
Figure 7 - Timing Information for MT9042
3-110
MT9042
Preliminary Information
AC Electrical Characteristics (see Fig. 8)† - Voltages are with respect to ground (VSS) unless otherwise stated.
Characteristics
1 C
L
2
O
3 C
K
4
Sym
Min
Typ‡
Max
Units
Master clock input rise time
trMCLKi
4
ns
Master clock input fall time
tfMCLKi
4
ns
Master clock frequency
tpMCLKi
Duty Cycle of the master clock
19.99936
20
20.000640
MHz
40
50
60
%
Test Conditions
† Timing is over recommended temperature & power supply voltages
‡ Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing
tfMCLK
trMCLK
MCLKi
2.4V
1.5V
0.4V
Figure 8 - Master Clock Input
3-111
MT9042
Notes:
3-112
Preliminary Information