TI TMS320C5515AZCHA10

TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
TMS320C5515 Fixed-Point Digital Signal Processor
Check for Samples: TMS320C5515
1 Fixed-Point Digital Signal Processor
1.1
TMS320C5515 Features
• HIGHLIGHTS:
• High-Perf/Low-Power, C55x™ Fixed-Point DSP
– 16.67/13.33/10/8.33-ns Instruction Cycle Time
– 60-, 75-, 100-, 120-MHz Clock Rate
• 320K Bytes On-Chip RAM
• 16-/8-Bit External Memory Interface (EMIF)
• Two MultiMedia Card/Secure Digital I/Fs
• Serial-Port I/F (SPI) With Four Chip-Selects
• Four Inter-IC Sound (I2S Bus™)
• USB 2.0 Full- and High-Speed Device
• LCD Bridge With Asynchronous Interface
• Tightly-Coupled FFT Hardware Accelerator
• 10-Bit 4-Input SAR ADC
• Real-Time Clock (RTC) With Crystal Input
• Four Core Isolated Power Supply Domains
• Four I/O Isolated Power Supply Domains
• Three integrated LDOs
• Industrial Temperature Devices Available
• 1.05-V Core, 1.8/2.5/2.8/3.3-V I/Os
• 1.3-V Core, 1.8/2.5/2.8/3.3-V I/Os
• FEATURES:
• High-Performance, Low-Power, TMS320C55x™
Fixed-Point Digital Signal Processor
– 16.67-, 13.33, 10-, 8.33-ns Instruction Cycle
Time
– 60-, 75-, 100-, 120-MHz Clock Rate
– One/Two Instruction(s) Executed per Cycle
– Dual Multipliers [Up to 200 or 240 Million
Multiply-Accumulates per Second (MMACS)]
– Two Arithmetic/Logic Units (ALUs)
– Three Internal Data/Operand Read Buses
and Two Internal Data/Operand Write Buses
– Fully Software-Compatible With C55x
Devices
– Industrial Temperature Devices Available
• 320 K Bytes Zero-Wait State On-Chip RAM,
Composed of:
– 64K Bytes of Dual-Access RAM (DARAM),
8 Blocks of 4K x 16-Bit
– 256K Bytes of Single-Access RAM (SARAM),
32 Blocks of 4K x 16-Bit
• 128K Bytes of Zero Wait-State On-Chip ROM
(4 Blocks of 16K x 16-Bit)
• 4M x 16-Bit Maximum Addressable External
Memory Space (SDRAM/mSDRAM)
• 16-/8-Bit External Memory Interface (EMIF) with
Glueless Interface to:
– 8-/16-Bit NAND Flash, 1- and 4-Bit ECC
– 8-/16-Bit NOR Flash
– Asynchronous Static RAM (SRAM)
– SDRAM/mSDRAM (1.8-, 2,5-, and 3.3-V)
• Direct Memory Access (DMA) Controller
– Four DMA With 4 Channels Each
(16-Channels Total)
• Three 32-Bit General-Purpose Timers
– One Selectable as a Watchdog and/or GP
• Two MultiMedia Card/Secure Digital (MMC/SD)
Interfaces
• Universal Asynchronous Receiver/Transmitter
(UART)
• Serial-Port Interface (SPI) With Four
Chip-Selects
• Master/Slave Inter-Integrated Circuit (I2C Bus™)
• Four Inter-IC Sound (I2S Bus™) for Data
Transport
• Device USB Port With Integrated 2.0
High-Speed PHY that Supports:
– USB 2.0 Full- and High-Speed Device
• LCD Bridge With Asynchronous Interface
• Tightly-Coupled FFT Hardware Accelerator
• 10-Bit 4-Input Successive Approximation (SAR)
ADC
• Real-Time Clock (RTC) With Crystal Input, With
Separate Clock Domain, Separate Power
Supply
• Four Core Isolated Power Supply Domains:
Analog, RTC, CPU and Peripherals, and USB
• Four I/O Isolated Power Supply Domains: RTC
I/O, EMIF I/O, USB PHY, and DVDDIO
• Three integrated LDOs (DSP_LDO, ANA_LDO,
and USB_LDO) to power the isolated domains:
DSP Core, Analog, and USB Core, respectively
• Low-Power S/W Programmable Phase-Locked
Loop (PLL) Clock Generator
• On-Chip ROM Bootloader (RBL) to Boot From
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCT PREVIEW information concerns products in the formative
or design phase of development. Characteristic data and other
specifications are design goals. Texas Instruments reserves the right
to change or discontinue these products without notice.
Copyright © 2010, Texas Instruments Incorporated
PRODUCT PREVIEW
1
TMS320C5515
SPRS645 – JANUARY 2010
•
•
•
•
•
www.ti.com
NAND Flash, NOR Flash, SPI EEPROM, SPI
Serial Flash or I2C EEPROM
IEEE-1149.1 (JTAG™)
Boundary-Scan-Compatible
Up to 26 General-Purpose I/O (GPIO) Pins
(Multiplexed With Other Device Functions)
196-Terminal Pb-Free Plastic BGA (Ball Grid
Array) (ZCH Suffix)
1.05-V Core (60 or 75MHz), 1.8-V, 2.5-V, 2.8-V,
or 3.3-V I/Os
1.3-V Core (100, 120 MHz), 1.8-V, 2.5-V, 2.8-V, or
3.3-V I/Os
• Applications:
– Wireless Audio Devices (e.g., Headsets,
Microphones, Speakerphones, etc.)
– Echo Cancellation Headphones
– Portable Medical Devices
– Voice Applications
– Industrial Controls
– Fingerprint Biometrics
– Software Defined Radio
• Community Resources
– TI E2E Community
– TI Embedded Processors Wiki
PRODUCT PREVIEW
2
Fixed-Point Digital Signal Processor
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
1.2
SPRS645 – JANUARY 2010
Description
The TMS320C5515 is a member of TI's TMS320C5000™ fixed-point Digital Signal Processor (DSP)
product family and is designed for low-power applications.
The TMS320C5515 fixed-point DSP is based on the TMS320C55x™ DSP generation CPU processor
core. The C55x™ DSP architecture achieves high performance and low power through increased
parallelism and total focus on power savings. The CPU supports an internal bus structure that is
composed of one program bus, one 32-bit data read bus and two 16-bit data read buses, two 16-bit data
write buses, and additional buses dedicated to peripheral and DMA activity. These buses provide the
ability to perform up to four 16-bit data reads and two 16-bit data writes in a single cycle. The
TMS320C5515 also includes four DMA controllers, each with 4 channels, providing data movements for
16-independent channel contexts without CPU intervention. Each DMA controller can perform one 32-bit
data transfer per cycle, in parallel and independent of the CPU activity.
The C55x CPU supports a variable byte width instruction set for improved code density. The Instruction
Unit (IU) performs 32-bit program fetches from internal or external memory and queues instructions for the
Program Unit (PU). The Program Unit decodes the instructions, directs tasks to the Address Unit (AU) and
Data Unit (DU) resources, and manages the fully protected pipeline. Predictive branching capability avoids
pipeline flushes on execution of conditional instructions.
The general-purpose input and output functions along with the 10-bit SAR ADC provide sufficient pins for
status, interrupts, and bit I/O for LCD displays, keyboards, and media interfaces. Serial media is supported
through two MultiMedia Card/Secure Digital (MMC/SD) peripherals, four Inter-IC Sound (I2S Bus™)
modules, one Serial-Port Interface (SPI) with up to 4 chip selects, one I2C multi-master and slave
interface, and a Universal Asynchronous Receiver/Transmitter (UART) interface.
The C5515 peripheral set includes an external memory interface (EMIF) that provides glueless access to
asynchronous memories like EPROM, NOR, NAND, and SRAM, as well as to high-speed, high-density
memories such as synchronous DRAM (SDRAM) and mobile SDRAM (mSDRAM). Additional peripherals
include: a high-speed Universal Serial Bus (USB2.0) device mode only, and a real-time clock (RTC). This
device also includes three general-purpose timers with one configurable as a watchdog timer, and an
analog phase-locked loop (APLL) clock generator.
In addition, the C5515 includes a tightly-coupled FFT Hardware Accelerator. The tightly-coupled FFT
Hardware Accelerator supports 8 to 1024-point (in power of 2) real and complex-valued FFTs.
Furthermore, the C5515 includes three integrated LDOs (DSP_LDO, ANA_LDO, and USB_LDO) to power
different sections of the device. The DSP_LDO can provide 1.3 V or 1.05 V to the DSP core (CVDD). To
allow for lowest power operation, the programmer can shutdown the internal DSP_LDO cutting power to
the DSP core (CVDD) while an external supply provides power to the RTC (CVDDRTC and DVDDRTC). The
ANA_LDO is designed to provide 1.3 V to the DSP PLL (VDDA_PLL), SAR, and power management circuits
(VDDA_ANA). The USB_LDO provides 1.3 V to USB core digital (USB_VDD1P3) and PHY circuits
(USB_VDDA1P3). The RTC alarm interrupt or the WAKEUP pin can re-enable the internal DSP_LDO and
re-apply power to the DSP core.
The C5515 is supported by the industry’s award-winning eXpressDSP™, Code Composer Studio™
Integrated Development Environment (IDE), DSP/BIOS™, Texas Instruments’ algorithm standard, and the
industry’s largest third-party network. Code Composer Studio IDE features code generation tools including
a C Compiler and Linker, RTDX™, XDS100™, XDS510™, XDS560™ emulation device drivers, and
evaluation modules. The C5515 is also supported by the C55x DSP Library which features more than 50
foundational software kernels (FIR filters, IIR filters, FFTs, and various math functions) as well as chip
support libraries.
Fixed-Point Digital Signal Processor
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
3
PRODUCT PREVIEW
The C55x CPU provides two multiply-accumulate (MAC) units, each capable of 17-bit x 17-bit
multiplication and a 32-bit add in a single cycle. A central 40-bit arithmetic/logic unit (ALU) is supported by
an additional 16-bit ALU. Use of the ALUs is under instruction set control, providing the ability to optimize
parallel activity and power consumption. These resources are managed in the Address Unit (AU) and Data
Unit (DU) of the C55x CPU.
TMS320C5515
SPRS645 – JANUARY 2010
1.3
www.ti.com
Functional Block Diagram
Figure 1-1 shows the functional block diagram of the C5515 device.
DSP System
Input
Clock(s)
JTAG Interface
C55x™ DSP CPU
PLL/Clock
Generator
FFT Hardware
Accelerator
Power
Management
64 KB DARAM
Pin
Multiplexing
256 KB SARAM
128 KB ROM
Switched Central Resource (SCR)
Peripherals
Interconnect
PRODUCT PREVIEW
DMA
(x4)
Program/Data Storage
Serial Interfaces
I2S
(x4)
I2C
SPI
App-Spec
Display
Connectivity
10-Bit
SAR
ADC
LCD
Bridge
USB 2.0
PHY (HS)
[DEVICE]
NAND, NOR,
SRAM, mSDRAM
UART
MMC/SD
(x2)
System
RTC
GP Timer
(x2)
GP Timer
or WD
LDOs
Figure 1-1. TMS320C5515 Functional Block Diagram
4
Fixed-Point Digital Signal Processor
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
2
3
4
............... 1
1.1
TMS320C5515 Features ............................. 1
1.2
Description ........................................... 3
1.3
Functional Block Diagram ............................ 4
Device Overview ........................................ 6
2.1
Device Characteristics ............................... 6
2.2
C55x CPU ............................................ 8
2.3
Memory Map Summary ............................. 14
2.4
Pin Assignments .................................... 15
2.5
Terminal Functions ................................. 16
2.6
Device Support ..................................... 41
Device Configuration ................................. 44
3.1
System Registers ................................... 44
3.2
Power Considerations .............................. 45
3.3
Clock Considerations ............................... 49
3.4
Boot Sequence ..................................... 51
3.5
Configurations at Reset ............................ 54
3.6
Configurations After Reset ......................... 55
3.7
Multiplexed Pin Configurations ..................... 59
3.8
Debugging Considerations ......................... 62
Device Operating Conditions ....................... 65
Fixed-Point Digital Signal Processor
4.1
4.2
4.3
5
5.1
5.2
Parameter Information .............................. 70
Recommended Clock and Control Signal Transition
Behavior ............................................ 70
5.3
5.4
Power Supplies ..................................... 71
External Clock Input From RTC_XI, CLKIN, and
USB_MXI Pins ...................................... 73
5.5
......................................... 77
........... 80
Reset ............................................... 81
Wake-up Events, Interrupts, and XF ............... 85
External Memory Interface (EMIF) ................. 87
Multimedia Card/Secure Digital (MMC/SD) ....... 102
Real-Time Clock (RTC) ........................... 107
Inter-Integrated Circuit (I2C) ...................... 109
5.6
5.7
5.8
5.9
5.10
5.11
5.12
5.13
5.14
5.15
5.16
5.17
5.18
Absolute Maximum Ratings Over Operating Case
Temperature Range (Unless Otherwise Noted) .... 65
Recommended Operating Conditions .............. 66
Electrical Characteristics Over Recommended
Ranges of Supply Voltage and Operating
Temperature (Unless Otherwise Noted) ............ 67
Peripheral Information and Electrical
Specifications .......................................... 70
5.19
5.20
6
Clock PLLs
Direct Memory Access (DMA) Controller
Universal Asynchronous Receiver/Transmitter
(UART) ............................................ 114
...............................
Liquid Crystal Display Controller (LCDC) .........
Serial Port Interface (SPI) .........................
Universal Serial Bus (USB) 2.0 Controller ........
General-Purpose Timers ..........................
General-Purpose Input/Output ....................
IEEE 1149.1 JTAG ................................
Inter-IC Sound (I2S)
116
122
132
135
142
144
148
Mechanical Packaging and Orderable
Information ............................................ 150
6.1
Thermal Data for ZCH
6.2
Packaging Information
.............................
............................
Contents
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
150
150
5
PRODUCT PREVIEW
1
SPRS645 – JANUARY 2010
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
2 Device Overview
2.1
Device Characteristics
Table 2-1, provides an overview of the TMS320C5515 DSP. The tables show significant features of the
C5515 device, including the capacity of on-chip RAM, the peripherals, the CPU frequency, and the
package type with pin count. For more detailed information on the actual device P/N and maximum device
operating frequency, see Section 2.6.2, Device and Development-Support Tool Nomenclature.
Table 2-1. Characteristics of the C5515 Processor
HARDWARE FEATURES
C5515
Asynchronous (8/16-bit bus width) SRAM,
Flash (NOR, NAND),
SDRAM and Mobile SDRAM (16-bit bus width) (1)
Peripherals
External Memory Interface (EMIF)
Not all peripheral pins are
available at the same time
Flash Cards
(for more detail, see the
Device Configurations
DMA
section).
2 MMC/SD
Four DMA controllers each with four channels,
for a total of 16 channels
PRODUCT PREVIEW
Timers
2 32-Bit General-Purpose (GP) Timers
1 Additional Configurable as a 32-Bit GP Timer and/or a
Watchdog
UART
1 (with RTS/CTS flow control)
SPI
1 with 4 chip selects
I2C
1 (Master/Slave)
I2S
4 (Two Channel, Full Duplex Communication)
USB 2.0 (Device only)
High- and Full-Speed Device
256 byte read/write buffer, max 50-MHz clock for SD cards,
and signaling for DMA transfers
MMC/SD
LCD Bridge
1 (8-bit or 16-bit asynchronous parallel bus)
ADC (Successive Approximation [SAR])
1 (10-bit, 4-input, 16-ms conversion time)
Real-Time Clock (RTC)
1 (Crystal Input, Separate Clock Domain and Power Supply)
FFT Hardware Accelerator
1 (Supports 8 to 1024-point 16-bit real and complex FFT)
Up to 26 pins (with 1 Additional General-Purpose Output (XF)
and 4 Special-Purpose Outputs for Use With SAR)
General-Purpose Input/Output Port (GPIO)
Size (Bytes)
On-Chip Memory
•
•
•
Organization
JTAG BSDL_ID
JTAGID Register
(Value is: 0009_702F)
CPU Frequency
MHz
Cycle Time
ns
Voltage
320 KB RAM, 128KB ROM
64KB On-Chip Dual-Access RAM (DARAM)
256 KB On-Chip Single-Access RAM (SARAM)
128KB On-Chip Single-Access ROM (SAROM)
see Figure 5-43
1.05-V Core
60 or 75 MHz
1.3-V Core
100, 120 MHz
1.05-V Core
16.67, 13.3 ns
1.3-V Core
10, 8.33 ns
1.05 V (60, 75 MHz)
Core (V)
1.3 V (100, 120 MHz)
I/O (V)
LDOs
(1)
6
1.8 V, 2.5 V, 2.8 V, 3.3 V
DSP_LDO
1.3 V or 1.05 V, TBD mA max current for DSP CPU (CVDD)
ANA_LDO
1.3 V, TBD mA max current for PLL (VDDA_PLL), SAR, and
power management circuits (VDDA_ANA)
USB_LDO
1.3 V, TBD mA max current for USB core digital (USB_VDD1P3)
and PHY circuits (USB_VDDA1P3)
For more compatibility with SDRAM devices, see Section 5.9 , External Memory Interface (EMIF).
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Table 2-1. Characteristics of the C5515 Processor (continued)
HARDWARE FEATURES
Active @ Room Temp 25°C, 75% DMAC +
25% ADD (Typical Sine Wave Data
Switching)
0.15 mW/MHz @ 1.05 V, 60 or 75 MHz
0.22 mW/MHz @ 1.3 V, 100 or 120 MHz
Active @ Room Temp 25°C, 75% DMAC +
25% NOP (Typical Sine Wave Data
Switching)
0.14 mW/MHz @ 1.05 V, 60 or 75MHz
0.22 mW/MHz @ 1.3 V, 100 or 120 MHz
Active @ Room Temp 25°C, Hardware FFT
Accelerator 1024-pt FFT, ROM Execution
0.25 mW/MHz @ 1.05 V, 60 or 75 MHz
0.31 mW/MHz @ 1.3 V, 100 or 120 MHz
Standby (Master Clock Disabled) @ Room
Temp 25°C (DARAM and SARAM in Active
Mode)
0.26 mW @ 1.05 V
0.44 mW @ 1.3 V
Standby (Master Clock Disabled) @ Room
Temp 25°C (DARAM in Retention and
SARAM in Active Mode)
0.23 mW @ 1.05 V
0.40 mW @ 1.3 V
Standby (Master Clock Disabled) @ Room
Temp 25°C (DARAM in Active Mode and
SARAM in Retention)
0.15 mW @ 1.05 V
0.28 mW @ 1.3 V
PLL Options
Software Programmable Multiplier
BGA Package
10 x 10 mm
Process Technology
mm
Product Status
(2)
(2)
x4 to x4099 multiplier
196-Pin BGA (ZCH)
0.09 mm
Product Preview (PP),
Advance Information (AI),
or Production Data (PD)
PRODUCT PREVIEW
Power Characterization
C5515
PP
PRODUCT PREVIEW information concerns experimental products (designated as TMX) that are in the formative or design phase of
development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or
discontinue these products without notice.
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
7
TMS320C5515
SPRS645 – JANUARY 2010
2.2
www.ti.com
C55x CPU
The TMS320C5515 fixed-point digital signal processor (DSP) is based on the C55x CPU 3.3 generation
processor core. The C55x DSP architecture achieves high performance and low power through increased
parallelism and total focus on power savings. The CPU supports an internal bus structure that is
composed of one program bus, three data read buses (one 32-bit data read bus and two 16-bit data read
buses), two 16-bit data write buses, and additional buses dedicated to peripheral and DMA activity. These
buses provide the ability to perform up to four data reads and two data writes in a single cycle. Each DMA
controller can perform one 32-bit data transfer per cycle, in parallel and independent of the CPU activity.
The C55x CPU provides two multiply-accumulate (MAC) units, each capable of 17-bit x 17-bit
multiplication in a single cycle. A central 40-bit arithmetic/logic unit (ALU) is supported by an additional
16-bit ALU. Use of the ALUs is under instruction set control, providing the ability to optimize parallel
activity and power consumption. These resources are managed in the Address Unit (AU) and Data Unit
(DU) of the C55x CPU.
The C55x DSP generation supports a variable byte width instruction set for improved code density. The
Instruction Unit (IU) performs 32-bit program fetches from internal or external memory, stores them in a
128-byte Instruction Buffer Queue, and queues instructions for the Program Unit (PU). The Program Unit
decodes the instructions, directs tasks to AU and DU resources, and manages the fully protected pipeline.
Predictive branching capability avoids pipeline flushes on execution of conditional instructions calls.
PRODUCT PREVIEW
For more detailed information on the CPU, see the TMS320C55x CPU 3.0 CPU Reference Guide
(literature number SWPU073).
The C55x core of the C5515 can address 16M bytes of unified data and program space. It also addresses
64K words of I/O space. The C5515 includes three types of on-chip memory: 128 KB read-only memory
(ROM), 256 KB single-access random access memory (SARAM), 64 KB dual-access random access
memory (DARAM). The memory map is shown in Figure 2-1 .
8
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
2.2.1
SPRS645 – JANUARY 2010
On-Chip Dual-Access RAM (DARAM)
The DARAM is located in the byte address range 000000h − 00FFFFh and is composed of eight blocks of
4K words each (see Table 2-2). Each DARAM block can perform two accesses per cycle (two reads, two
writes, or a read and a write). The DARAM can be accessed by the internal program, data, or DMA buses.
(1)
2.2.2
CPU
BYTE ADDRESS RANGE
DMA CONTROLLER
BYTE ADDRESS RANGE
MEMORY BLOCK
000000h – 001FFFh
0001 0000h – 0001 1FFFh
DARAM 0 (1)
002000h – 003FFFh
0001 2000h – 0001 3FFFh
DARAM 1
004000h – 005FFFh
0001 4000h – 0001 5FFFh
DARAM 2
006000h – 007FFFh
0001 6000h – 0001 7FFFh
DARAM 3
008000h – 009FFFh
0001 8000h – 0001 9FFFh
DARAM 4
00A000h – 00BFFFh
0001 A000h – 0001 BFFFh
DARAM 5
00C000h – 00DFFFh
0001 C000h – 0001 DFFFh
DARAM 6
00E000h – 00FFFFh
0001 E000h – 0001 FFFFh
DARAM 7
The first 192 bytes are reserved for memory-mapped registers (MMRs). See Figure 2-1 ,
TMS320C5515 Memory Map Summary.
On-Chip Single-Access RAM (SARAM)
The SARAM is located at the byte address range 010000h – 04FFFF h and is composed of 32 blocks of
4K words each (see Table 2-3). Each SARAM block can perform one access per cycle (one read or one
write). SARAM can be accessed by the internal program, data, or DMA buses. SARAM is also accessed
by the USB and LCD DMA buses.
Table 2-3. SARAM Blocks
CPU
BYTE ADDRESS RANGE
DMA/USB CONTROLLER
BYTE ADDRESS RANGE
MEMORY BLOCK
010000h − 011FFFh
0009 0000h – 0009 1FFFh
SARAM 0
012000h − 013FFFh
0009 2000h – 0009 3FFFh
SARAM 1
014000h − 015FFFh
0009 4000h – 0009 5FFFh
SARAM 2
016000h − 017FFFh
0009 6000h – 0009 7FFFh
SARAM 3
018000h − 019FFFh
0009 8000h – 0009 9FFFh
SARAM 4
01A000h − 01BFFFh
0009 A000h – 0009 BFFFh
SARAM 5
01C000h − 01DFFFh
0009 C000h – 0009 DFFFh
SARAM 6
01E000h − 01FFFFh
0009 E000h – 0009 FFFFh
SARAM 7
020000h − 021FFFh
000A 0000h – 000A 1FFFh
SARAM 8
022000h − 023FFFh
000A 2000h – 000A 3FFFh
SARAM 9
024000h − 025FFFh
000A 4000h – 000A 5FFFh
SARAM 10
026000h − 027FFFh
000A 6000h – 000A 7FFFh
SARAM 11
028000h − 029FFFh
000A 8000h – 000A 9FFFh
SARAM 12
02A000h − 02BFFFh
000A A000h – 000A BFFFh
SARAM 13
02C000h − 02DFFFh
000A C000h – 000A DFFFh
SARAM 14
02E000h − 02FFFFh
000A E000h – 000A FFFFh
SARAM 15
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
9
PRODUCT PREVIEW
Table 2-2. DARAM Blocks
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
Table 2-3. SARAM Blocks (continued)
PRODUCT PREVIEW
(1)
2.2.3
CPU
BYTE ADDRESS RANGE
DMA/USB CONTROLLER
BYTE ADDRESS RANGE
MEMORY BLOCK
030000h − 031FFFh
000B 0000h – 000B 1FFFh
SARAM 16
032000h − 033FFFh
000B 2000h – 000B 3FFFh
SARAM 17
034000h − 035FFFh
000B 4000h – 000B 5FFFh
SARAM 18
036000h − 037FFFh
000B 6000h – 000B 7FFFh
SARAM 19
038000h − 039FFFh
000B 8000h – 000B 9FFFh
SARAM 20
03A000h − 03BFFFh
000B A000h – 000B BFFFh
SARAM 21
03C000h − 03DFFFh
000B C000h – 000B DFFFh
SARAM 22
03E000h − 03FFFFh
000B E000h – 000B FFFFh
SARAM 23
040000h – 041FFFh
000C 0000h – 000C 1FFFh
SARAM 24
042000h – 043FFFh
000C 2000h – 000C 3FFFh
SARAM 25
044000h – 045FFFh
000C 4000h – 000C 5FFFh
SARAM 26
046000h – 047FFFh
000C 6000h – 000C 7FFFh
SARAM 27
048000h – 049FFFh
000C 8000h – 000C 9FFFh
SARAM 28
04A000h – 04BFFFh
000C A000h – 000C BFFFh
SARAM 29
04C000h – 04DFFFh
000C C000h – 000C DFFFh
SARAM 30
04E000h – 04FFFFh
000C E000h – 000C FFFFh
SARAM 31 (1)
SARAM31 (byte address range: 0x4E000 – 0x4EFFF) is reserved for the bootloader. After the boot
process is complete, this memory space can be used.
On-Chip Read-Only Memory (ROM)
The zero-wait-state ROM is located at the byte address range FE0000h – FFFFFFh. The ROM is
composed of four 16K-word blocks, for a total of 128K bytes of ROM. The ROM address space can be
mapped by software to the external memory or to the internal ROM.
The standard C5515 device includes a Bootloader program resident in the ROM.
When the MPNMC bit field of the ST3 status register is cleared (by default), the byte address range
FE0000h – FFFFFFh is reserved for the on-chip ROM. When the MPNMC bit field of the ST3 status
register is set through software, the on-chip ROM is disabled and not present in the memory map, and
byte address range FE0000h – FFFFFFh is directed to external memory space. A hardware reset always
clears the MPNMC bit, so it is not possible to disable the ROM at reset. However, the software reset
instruction does not affect the MPNMC bit. The ROM can be accessed by the program and data buses.
Each on-chip ROM block is a one cycle per word access memory.
2.2.4
External Memory
The external memory space of the device is located at the byte address range 050000h – FFFFFFh. The
external memory space is divided into five chip select spaces: one dedicated to SDRAM and mobile
SDRAM (EMIF CS0 or CS[1:0] space), and the remainder (EMIF CS2 through CS5 space) dedicated to
asynchronous devices including flash. Each chip select space has a corresponding chip select pin (called
EMIF_CSx) that is activated during an access to the chip select space.
The external memory interface (EMIF) provides the means for the DSP to access external memories and
other devices including: mobile single data rate (SDR) synchronous dynamic RAM (SDRAM and
mSDRAM), NOR Flash, NAND Flash, and asynchronous static RAM (SRAM). Before accessing external
memory, you must configure the EMIF through its memory-mapped registers.
10
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
PRODUCT PREVIEW
The EMIF provides a configurable 16- or 8-bit data bus, an address bus width of up to 21-bits, and 5
dedicated chip selects, along with memory control signals. To maximize power savings, the I/O pin of the
EMIF can be operated at an independent voltage from the rest of other I/O pins on the device.
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
11
TMS320C5515
SPRS645 – JANUARY 2010
2.2.5
www.ti.com
I/O Memory
The C5515 DSP includes a 64K byte I/O space for the memory-mapped registers of the DSP peripherals
and system registers used for idle control, status monitoring and system configuration. I/O space is
separate from program/memory space and is accessed with separate instruction opcodes or via the
DMA's.
Table 2-4 lists the memory-mapped registers of the device. Note that not all addresses in the 64K byte I/O
space are used; these addresses should be treated as RESERVED and not accessed by the CPU nor
DMA. For the expanded tables of each peripheral, see Section 5, Peripheral Information and Electrical
Specifications of this document.
Some DMA controllers have access to the I/O-Space memory-mapped registers of the following
peripherals registers: I2C, UART, I2S, MMC/SD, EMIF, USB, and SAR ADC .
Before accessing any peripheral memory-mapped register, make sure the peripheral being accessed is
not held in reset via the Peripheral Reset Control Register (PRCR) and its internal clock is enabled via the
Peripheral Clock Gating Control Registers (PCGCR1 and PCGCR2).
Table 2-4. Peripheral I/O-Space Control Registers
PRODUCT PREVIEW
12
WORD ADDRESS
PERIPHERAL
0x0000 – 0x0004
Idle Control
0x0005 – 0x000D through 0x0803 – 0x0BFF
Reserved
0x0C00 – 0x0C7F
DMA0
0x0C80 – 0x0CFF
Reserved
0x0D00 – 0x0D7F
DMA1
0x0D80 – 0x0DFF
Reserved
0x0E00 – 0x0E7F
DMA2
0x0E80 – 0x0EFF
Reserved
0x0F00 – 0x0F7F
DMA3
0x0F80 – 0x0FFF
Reserved
0x1000 – 0x10DD
EMIF
0x10EE – 0x10FF through 0x1300 – 0x17FF
Reserved
0x1800 – 0x181F
Timer0
0x1820 – 0x183F
Reserved
0x1840 – 0x185F
Timer1
0x1860 – 0x187F
Reserved
0x1880 – 0x189F
Timer2
0x1900 – 0x197F
RTC
0x1980 – 0x19FF
Reserved
0x1A00 – 0x1A6C
I2C
0x1A6D – 0x1AFF
Reserved
0x1B00 – 0x1B1F
UART
0x1B80 – 0x1BFF
Reserved
0x1C00 – 0x1CFF
System Control
0x1D00 – 0x1FFF through 0x2600 – 0x27FF
Reserved
0x2800 – 0x2840
I2S0
0x2900 – 0x2940
I2S1
0x2A00 – 0x2A40
I2S2
0x2B00 – 0x2B40
I2S3
0x2C41 – 0x2DFF
Reserved
0x2E00 – 0x2E40
LCD
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Table 2-4. Peripheral I/O-Space Control Registers (continued)
WORD ADDRESS
PERIPHERAL
0x2E41 – 0x2FFF
Reserved
0x3000 – 0x300F
SPI
0x3010 – 0x39FF
Reserved
0x3A00 – 0x3A1F
MMC/SD0
0x3A20 – 0x3AFF
Reserved
0x3B00 – 0x3B1F
MMC/SD1
Reserved
0x7000 – 0x70FF
SAR and Analog Control Registers
0x7100 – 0x7FFF
Reserved
0x8000 – 0xFFFF
USB
PRODUCT PREVIEW
0x3B2F – 0x6FFF
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
13
TMS320C5515
SPRS645 – JANUARY 2010
2.3
www.ti.com
Memory Map Summary
The C5515 provides 16M bytes of total memory space composed of on-chip RAM, on-chip ROM, and
external memory space supporting a variety of memory types. The on-chip, dual-access RAM allows two
accesses to a given block during the same cycle. The C5515 supports 8 blocks of 4K words of
dual-access RAM. The on-chip, single-access RAM allows one access to a given block per cycle. The
C5515 supports 32 blocks of 4K words of single-access RAM.
The remainder of the memory map is divided into five external spaces, and on-chip ROM. Each external
space has a chip select decode signal (called CS0, CS[2:5]) that indicates an access to the selected
space. The external memory interface (EMIF) supports access to asynchronous memories such as SRAM,
NAND, or NOR and Flash, and mobile single data rate (mSDR) and single data rate (SDR) SDRAM.
The DSP memory is accessible by different master modules within the DSP, including the C55x CPU, the
four DMA controllers, LCD, and USB (see Figure 2-1 ).
CPU BYTE
DMA/USB/LCD
ADDRESS(A)
BYTE ADDRESS(A)
000000h
0001 0000h
0000C0h
0001 00C0h
MEMORY BLOCKS
MMR (Reserved)
PRODUCT PREVIEW
DARAM
010000h
BLOCK SIZE
(B)
(D)
64K Minus 192 Bytes
0009 0000h
256K Bytes
SARAM
050000h
0100 0000h
External-CS0 Space
800000h
C00000h
E00000h
F00000h
FE0000h
A.
B.
C.
D.
E.
8M Minus 320K Bytes SDRAM/mSDRAM
0200 0000h
External-CS2 Space
(C)
External-CS3 Space
(C)
2M Bytes Asynchronous
External-CS4 Space
(C)
1M Bytes Asynchronous
External-CS5 Space
(C)
1M Minus 128K Bytes Asynchronous
4M Bytes Asynchronous
0300 0000h
0400 0000h
0500 0000h
050E 0000h
ROM
(if MPNMC=0)
FFFFFFh
(C)(E)
External-CS5 Space
(if MPNMC=1)
(C)
128K Bytes Asynchronous (if MPNMC=1)
128K Bytes ROM (if MPNMC=0)
050F FFFFh
Address shown represents the first byte address in each block.
The first 192 bytes are reserved for memory-mapped registers (MMRs).
Out of the four DMA controllers, only DMA controller 3 has access to the external memory space.
The USB and LCD controllers do not have access to DARAM.
The CS0 space can be accessed by CS0 only or by CS0 and CS1.
Figure 2-1. TMS320C5515 Memory Map Summary
14
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
2.4
SPRS645 – JANUARY 2010
Pin Assignments
Extensive use of pin multiplexing is used to accommodate the largest number of peripheral functions in
the smallest possible package. Pin multiplexing is controlled using software programmable register
settings. For more information on pin muxing, see Section 3.7, Multiplexed Pin Configurations of this
document.
2.4.1
Pin Map (Bottom View)
P
EM_DQM1
DVDDEMIF
DVDDIO
LCD_
CS0_E0/
SPI_CS0
LCD_
RW_WRB/
SPI_CS2
LCD_D[0]/
SPI_RX
LCD_D[2]/
GP[12]
DVDDIO
LCD_D[5]/
GP[15]
LCD_D[7]/
GP[17]
LCD_D[9]/
I2S2_FS/
GP[19]/
SPI_CS0
LCD_D[11]/
I2S2_DX/
GP[27]/
SPI_TX
LCD_D[13]/
UART_CTS/
GP[29]/
I2S3_FS
LCD_D[15]/
UART_TXD/
GP[31]/
I2S3_DX
N
EM_A[15]/
GP[21]
EM_SDCKE
LCD_
EN_RDB/
SPI_CLK
LCD_
CS1_EN1/
SPI_CS1
LCD_RS/
SPI_CS3
LCD_D[1]/
SPI_TX
LCD_D[3]/
GP[13]
LCD_D[4]/
GP[14]
LCD_D[6]/
GP[16]
LCD_D[8]/
I2S2_CLK/
GP[18]/
SPI_CLK
LCD_D[10]/
I2S2_RX/
GP[20]/
SPI_RX
LCD_D[12]/
UART_RTS/
GP[28]/
I2S3_CLK
LCD_D[14]/
UART_RXD/
GP[30]/
I2S3_RX
DVDDIO
M
EM_A[14]
EM_D[5]
EM_SDCLK
EM_CS3
EMU1
TCK
TDO
XF
TRST
MMC0_D1/
I2S0_RX/
GP[3]
MMC0_CMD/
I2S0_FS/
GP[1]
MMC1_D1/
I2S1_RX/
GP[9]
MMC1_CLK/
I2S1_CLK/
GP[6]
MMC1_D0/
I2S1_DX/
GP[8]
L
EM_A[13]
EM_A[10]
EM_D[12]
EM_D[4]
CVDD
EMU0
TDI
TMS
MMC0_D0/
I2S0_DX/
GP[2]
MMC0_CLK/
I2S0_CLK/
GP[0]
MMC0_D3/
GP[5]
MMC0_D2/
GP[4]
MMC1_D3/
GP[11]
MMC1_CMD/
I2S1_FS/
GP[7]
K
EM_A[12]/
(CLE)
EM_A[11]/
(ALE)
EM_D[14]
EM_D[13]
EM_D[6]
EM_WAIT3
DVDDIO
VSS
VSS
CVDD
VSS
DVDDIO
VSS
MMC1_D2/
GP[10]
J
EM_A[8]
EM_A[9]
EM_A[20]/
GP[26]
EM_D[15]
DVDDEMIF
CVDD
VSS
VSS
VSS
RSV1
RSV2
USB_VBUS
USB_VDD1P3
USB_DM
H
EM_WE
EM_A[7]
EM_D[7]
EM_WAIT5
DVDDEMIF
VSS
DVDDEMIF
CVDD
USB_
VSSA1P3
USB_
VDDA1P3
USB_
VSSA3P3
USB_
VDDA3P3
USB_VSS1P3
USB_DP
G
EM_WAIT4
EM_A[18]/
GP[24]
EM_D[0]
EM_A[19]/
GP[25]
DVDDEMIF
VSS
VSS
USB_VDDPLL
USB_R1
F
EM_A[6]
EM_A[17]/
GP[23]
EM_D[2]
EM_D[9]
DVDDEMIF
CVDD
DVDDIO
DVDDRTC
VSS
VSS
USB_VSSOSC
USB_LDOO
LDOI
LDOI
E
EM_A[2]
EM_A[16]/
GP[22]
EM_D[8]
EM_OE
EM_D[1]
DVDDEMIF
INT1
WAKEUP
VSS
DSP_LDOO
VSS
VSS
VSS
VSS
D
EM_A[5]
EM_A[3]
EM_D[10]
EM_D[3]
EM_WAIT2
RESET
VSS
RTC_
CLKOUT
VSSA_PLL
GPAIN0
VSS
DSP_
LDO_EN
RSV16
RSV3
C
EM_A[4]
EM_A[1]
EM_CS4
EM_D[11]
EM_CS2
INT0
CLK_SEL
CVDDRTC
VSSRTC
VDDA_PLL
GPAIN3
RSV0
RSV5
RSV4
B
EM_BA[1]
EM_A[0]
EM_CS0
EM_SDCAS
EM_DQM0
EM_R/W
SCL
SDA
RTC_XI
VSSA_ANA
GPAIN2
LDOI
BG_CAP
VSSA_ANA
A
EM_BA[0]
DVDDEMIF
EM_CS5
EM_CS1
DVDDEMIF
EM_SDRAS
CLKOUT
CLKIN
RTC_XO
VDDA_ANA
GPAIN1
ANA_LDOO
VSS
VSS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
USB_VSSREF USB_VSSPLL USB_VDDOSC USB_M12XI
USB_M12XO
Figure 2-2. C5515 Pin Map
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
15
PRODUCT PREVIEW
Figure 2-2 shows the bottom view of the package pin assignments.
TMS320C5515
SPRS645 – JANUARY 2010
2.5
www.ti.com
Terminal Functions
The terminal functions tables (Table 2-5 through Table 2-22) identify the external signal names, the
associated pin (ball) numbers along with the mechanical package designator, the pin type, whether the pin
has any internal pullup or pulldown resistors or bus-holders, and a functional pin description. For more
detailed information on device configuration, peripheral selection, multiplexed/shared pins, and debugging
considerations, see the Device Configuration section of this data manual.
For proper device operation, external pullup/pulldown resistors may be required on some pins.
Section 3.8.1, Pullup/Pulldown Resistors discusses situations where external pullup/pulldown resistors are
required.
PRODUCT PREVIEW
16
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Table 2-5. Oscillator/PLL Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
DESCRIPTION
DSP clock output signal. For debug purposes, the CLKOUT pin can be used to tap
different clocks within the DSP clock generator. The SRC bits in the CLKOUT
Control Source Register (CCSSR) can be used to specify the CLKOUT pin source.
Additionally, the slew rate of the CLKOUT pin can be controlled by the Output
Slew Rate Control Register (OSRCR) [0x1C16].
CLKOUT
A7
O/Z
–
DVDDIO
BH
The CLKOUT pin is enabled/disabled through the CLKOFF bit in the CPU ST3_55
register. When disabled, the CLKOUT pin is placed in high-impedance (Hi-Z). At
reset the CLKOUT pin is enabled until the beginning of the boot sequence, when
the on-chip Bootloader sets CLKOFF = 1 and the CLKOUT pin is disabled (Hi-Z).
For more information on the ST3_55 register, see the TMS320C55x 3.0 CPU
Reference Guide (literature number: SWPU073).
Input clock. This signal is used to input an external clock when the 32-KHz on-chip
oscillator is not used as the DSP clock (pin CLK_SEL = 1). For boot purposes, the
CLKIN frequency is assumed to be either 11.2896, 12, or 12.288 MHz.
The CLK_SEL pin (C7) selects between the 32-KHz crystal clock or CLKIN.
A8
I
–
DVDDIO
BH
When the CLK_SEL pin is low, this pin should be tied to ground (VSS). When
CLK_SEL is high, this pin should be driven by an external clock source.
If CLK_SEL is high, this pin is used as the reference clock for the clock generator
and during bootup the bootloader bypasses the PLL and assumes the CLKIN
frequency is one of the following frequencies: 11.2896-, 12-, or 12.288-MHz. With
these frequencies in mind, the bootloader sets the SPI clock rates at 500 KHz and
the I2C clock rate at 400 KHz.
CLK_SEL
C7
I
–
DVDDIO
BH
Clock input select. This pin selects between the 32-KHz crystal clock or CLKIN.
0 = 32-KHz on-chip oscillator drives the RTC timer and the DSP clock generator
while CLKIN is ignored.
1 = CLKIN drives the DSP clock generator and the 32-KHz on-chip oscillator
drives only the RTC timer.
This pin is not allowed to change during device operation; it must be tied high or
low at the board.
(1)
(2)
(3)
VDDA_PLL
C10
PWR
see Section 4.2,
1.3-V Analog PLL power supply for the system clock generator.
ROC
VSSA_PLL
D9
GND
see Section 4.2,
Analog PLL ground for the system clock generator.
ROC
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, BH = Bus Holder
IPD = Internal pulldown, IPU = Internal pullup. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 3.8.1 , Pullup/Pulldown Resistors.
Specifies the operating I/O supply voltage for each signal
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
17
PRODUCT PREVIEW
CLKIN
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
Table 2-6. Real-Time Clock (RTC) Terminal Functions
SIGNAL
NAME
RTC_XO
NO.
A9
TYPE (1)
I
OTHER (2)
(3)
–
CVDDRTC
DESCRIPTION
Real-time clock oscillator output. This pin operates at the RTC core voltage,
CVDDRTC, and supports a 32.768-kHz crystal.
If the RTC oscillator is not used, it can be disabled by connecting RTC_XI to
CVDDRTC and RTC_XO to ground (VSS). A voltage must still be applied to CVDDRTC
(see Section 4.2, Recommended Operating Conditions).
Note: When RTC oscillator is disabled, the RTC registers (I/O address range 1900h
– 197Fh) are not accessible.
RTC_XI
B9
I
–
CVDDRTC
Real-time clock oscillator input.
If the RTC oscillator is not used, it can be disabled by connecting RTC_XI to
CVDDRTC and RTC_XO to ground (VSS). A voltage must still be applied to CVDDRTC
(see Section 4.2, Recommended Operating Conditions).
Note: When RTC oscillator is disabled, the RTC registers (I/O address range 1900h
– 197Fh) are not accessible.
PRODUCT PREVIEW
RTC_CLKOUT
D8
O/Z
WAKEUP
E8
I/O/Z
(1)
(2)
(3)
18
–
DVDDRTC
–
DVDDRTC
Real-time clock output pin. This pin operates at DVDDRTC voltage. The
RTC_CLKOUT pin is enabled/disabled through the RTCCLKOUTEN bit in the RTC
Power Management Register (RTCPMGT). At reset, the RTC_CLKOUT pin is
disabled (high-impedance [Hi-Z]).
The pin is used to WAKEUP the core from idle condition. This pin defaults to an
input at CVDDRTC powerup, but can also be configured as an active-low open-drain
output signal to wakeup an external device from an RTC alarm.
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, BH = Bus Holder
IPD = Internal pulldown, IPU = Internal pullup. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 3.8.1 , Pullup/Pulldown Resistors.
Specifies the operating I/O supply voltage for each signal
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Table 2-7. RESET, Interrupts, and JTAG Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
DESCRIPTION
RESET
External Flag Output. XF is used for signaling other processors in
multiprocessor configurations or XF can be used as a fast
general-purpose output pin.
XF
RESET
M8
O/Z
D6
I
–
DVDDIO
BH
IPU
DVDDIO
BH
XF is set high by the BSET XF instruction and XF is set low by the
BCLR XF instruction or by writing to bit 13 of the ST1_55 register. At
reset, the XF pin will be high. For more information on the ST1_55
register, see the TMS320C55x 3.0 CPU Reference Guide (literature
number: SWPU073).
Device reset. RESET causes the DSP to terminate execution and loads
the program counter with the contents of the reset vector. When
RESET is brought to a high level, the reset vector in ROM at FFFF00h
forces the program execution to branch to the location of the on-chip
ROM bootloader.
RESET affects the various registers and status bits.
The IPU resistor on this pin can be enabled or disabled via the
PDINHIBR2 register but will be forced ON when RESET is asserted.
TMS
TDO
TDI
TCK
(1)
(2)
(3)
L8
M7
I
O/Z
L7
M6
I
I
IPU
DVDDIO
BH
IEEE standard 1149.1 test mode select. This serial control input is
clocked into the TAP controller on the rising edge of TCK.
If the emulation header is located greater than 6 inches from the
device, TMS must be buffered. In this case, the input buffer for TMS
needs a pullup resistor connected to DVDDIO to hold these signals at a
known value when the emulator is not connected. A resistor value of
4.7 kΩ or greater is suggested. For board design guidelines related to
the emulation header, see the XDS560 Emulator Technical Reference
(literature number: SPRU589).
The IPU resistor on this pin can be enabled or disabled via the
PDINHIBR2 register.
–
DVDDIO
BH
IEEE standard 1149.1 test data output. The contents of the selected
register (instruction or data) are shifted out of TDO on the falling edge
of TCK. TDO is in the high-impedance (Hi-Z) state except when the
scanning of data is in progress.
For board design guidelines related to the emulation header, see the
XDS560 Emulator Technical Reference (literature number: SPRU589).
If the emulation header is located greater than 6 inches from the
device, TDO must be buffered.
IPU
DVDDIO
BH
IEEE standard 1149.1 test data input. TDI is clocked into the selected
register (instruction or data) on a rising edge of TCK.
If the emulation header is located greater than 6 inches from the
device, TDI must be buffered. In this case, the input buffer for TDI
needs a pullup resistor connected to DVDDIO to hold this signal at a
known value when the emulator is not connected. A resistor value of
4.7 kΩ or greater is suggested.
The IPU resistor on this pin can be enabled or disabled via the
PDINHIBR2 register.
IPU
DVDDIO
BH
IEEE standard 1149.1 test clock. TCK is normally a free-running clock
signal with a 50% duty cycle. The changes on input signals TMS and
TDI are clocked into the TAP controller, instruction register, or selected
test data register on the rising edge of TCK. Changes at the TAP output
signal (TDO) occur on the falling edge of TCK.
If the emulation header is located greater than 6 inches from the
device, TCK must be buffered.
For board design guidelines related to the emulation header, see the
XDS560 Emulator Technical Reference (literature number: SPRU589).
The IPU resistor on this pin can be enabled or disabled via the
PDINHIBR2 register.
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, BH = Bus Holder
IPD = Internal pulldown, IPU = Internal pullup. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 3.8.1 , Pullup/Pulldown Resistors.
Specifies the operating I/O supply voltage for each signal
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
19
PRODUCT PREVIEW
JTAG
[For more detailed information on emulation header design guidelines, see the XDS560 Emulator Technical Reference (literature number:
SPRU589).]
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
Table 2-7. RESET, Interrupts, and JTAG Terminal Functions (continued)
SIGNAL
NAME
TRST
EMU1
PRODUCT PREVIEW
EMU0
NO.
M9
M5
L6
TYPE (1)
I
I/O/Z
I/O/Z
OTHER (2)
(3)
DESCRIPTION
IPD
DVDDIO
BH
IEEE standard 1149.1 reset signal for test and emulation logic. TRST,
when high, allows the IEEE standard 1149.1 scan and emulation logic
to take control of the operations of the device. If TRST is not connected
or driven low, the device operates in its functional mode, and the IEEE
standard 1149.1 signals are ignored. The C5515 will not operate
properly if this reset pin is never asserted low.
For board design guidelines related to the emulation header, see the
XDS560 Emulator Technical Reference (literature number: SPRU589).
It is recommended that an external pulldown resistor be used in
addition to the IPD -- especially if there is a long trace to an emulation
header.
IPU
DVDDIO
BH
Emulator 1 pin. EMU1 is used as an interrupt to or from the emulator
system and is defined as input/output by way of the emulation logic.
For board design guidelines related to the emulation header, see the
XDS560 Emulator Technical Reference (literature number: SPRU589).
An external pullup to DVDDIO is required to provide a signal rise time of
less than 10 msec. A 4.7-kΩ resistor is suggested for most applications.
For board design guidelines related to the emulation header, see the
XDS560 Emulator Technical Reference (literature number: SPRU589).
The IPU resistor on this pin can be enabled or disabled via the
PDINHIBR2 register.
IPU
DVDDIO
BH
Emulator 0 pin. When TRST is driven low and then high, the state of
the EMU0 pin is latched and used to connect the JTAG pins (TCK,
TMS, TDI, TDO) to either the IEEE1149.1 Boundary-Scan TAP (when
the latched value of EMU0 = 0) or to the DSP Emulation TAP (when the
latched value of EMU0 = 1). Once TRST is high, EMU0 is used as an
interrupt to or from the emulator system and is defined as input/output
by way of the emulation logic.
An external pullup to DVDDIO is required to provide a signal rise time of
less than 10 msec. A 4.7-kΩ resistor is suggested for most applications.
For board design guidelines related to the emulation header, see the
XDS560 Emulator Technical Reference (literature number: SPRU589).
The IPU resistor on this pin can be enabled or disabled via the
PDINHIBR2 register.
EXTERNAL INTERRRUPTS
20
INT1
E7
I
IPU
DVDDIO
BH
INT0
C6
I
IPU
DVDDIO
BH
External interrupt inputs (INT1 and INT0). These pins are maskable via
their specific Interrupt Mask Register (IMR1, IMR0) and the interrupt
mode bit. The pins can be polled and reset by their specific Interrupt
Flag Register (IFR1, IFR0).
The IPU resistor on these pins can be enabled or disabled via the
PDINHIBR2 register.
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Table 2-8. External Memory Interface (EMIF) Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
DESCRIPTION
EMIF FUNCTIONAL PINS: ASYNC (NOR, SRAM, and NAND)
EM_A[20]/GP[26]
J3
I/O/Z
IPD
DVDDEMIF
BH
This pin is multiplexed between EMIF and GPIO. For EMIF, this pin is the EMIF
external address pin 20.
Mux control via the A20_MODE bit in the EBSR (see Figure 3-4).
The IPD resistor on this pin can be enabled or disabled via the PDINHIBR2 register.
This pin is multiplexed between EMIF and GPIO. For EMIF, this pin is the EMIF
external address pin 19.
Mux control via the A19_MODE bit in the EBSR (see Figure 3-4).
The IPD resistor on this pin can be enabled or disabled via the PDINHIBR2 register.
EM_A[19]/GP[25]
G4
I/O/Z
IPD
DVDDEMIF
BH
EM_A[18]/GP[24]
G2
I/O/Z
IPD
DVDDEMIF
BH
This pin is multiplexed between EMIF and GPIO. For EMIF, this pin is the EMIF
external address pin 18.
Mux control via the A18_MODE bit in the EBSR (see Figure 3-4).
The IPD resistor on this pin can be enabled or disabled via the PDINHIBR2 register.
EM_A[17]/GP[23]
F2
I/O/Z
IPD
DVDDEMIF
BH
This pin is multiplexed between EMIF and GPIO. For EMIF, this pin is the EMIF
external address pin 17.
Mux control via the A17_MODE bit in the EBSR (see Figure 3-4).
The IPD resistor on this pin can be enabled or disabled via the PDINHIBR2 register.
EM_A[16]/GP[22]
E2
I/O/Z
IPD
DVDDEMIF
BH
This pin is multiplexed between EMIF and GPIO. For EMIF, this pin is the EMIF
external address pin 16.
Mux control via the A16_MODE bit in the EBSR (see Figure 3-4).
The IPD resistor on this pin can be enabled or disabled via the PDINHIBR2 register.
EM_A[15]/GP[21]
N1
I/O/Z
IPD
DVDDEMIF
BH
This pin is multiplexed between EMIF and GPIO. For EMIF, this pin is the EMIF
external address pin 15.
Mux control via the A15_MODE bit in the EBSR (see Figure 3-4).
The IPD resistor on this pin can be enabled or disabled via the PDINHIBR2 register.
EM_A[14]
M1
I/O/Z
DVDDEMIF
BH
This pin is the EMIF external address pin 14.
EM_A[13]
L1
I/O/Z
DVDDEMIF
BH
This pin is the EMIF external address pin 13.
EM_A[12]/(CLE)
K1
I/O/Z
DVDDEMIF
BH
This pin is the EMIF external address pin 12. When interfacing with NAND Flash,
this pin also acts as Command Latch Enable (CLE).
EM_A[11]/(ALE)
K2
I/O/Z
DVDDEMIF
BH
This pin is the EMIF external address pin 11. When interfacing with NAND Flash,
this pin also acts as Address Latch Enable (ALE).
EM_A[10]
L2
I/O/Z
DVDDEMIF
BH
This pin is the EMIF external address pin 10.
EM_A[9]
J2
I/O/Z
DVDDEMIF
BH
This pin is the EMIF external address pin 9.
EM_A[8]
J1
I/O/Z
DVDDEMIF
BH
This pin is the EMIF external address pin 8.
EM_A[7]
H2
I/O/Z
DVDDEMIF
BH
This pin is the EMIF external address pin 7.
EM_A[6]
F1
I/O/Z
DVDDEMIF
BH
This pin is the EMIF external address pin 6.
EM_A[5]
D1
I/O/Z
DVDDEMIF
BH
This pin is the EMIF external address pin 5.
EM_A[4]
C1
I/O/Z
DVDDEMIF
BH
This pin is the EMIF external address pin 4.
EM_A[3]
D2
I/O/Z
DVDDEMIF
BH
This pin is the EMIF external address pin 3.
(1)
(2)
(3)
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, BH = Bus Holder
IPD = Internal pulldown, IPU = Internal pullup. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 3.8.1 , Pullup/Pulldown Resistors.
Specifies the operating I/O supply voltage for each signal
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
21
PRODUCT PREVIEW
Note: When accessing 8-bit Asynchronous memory, pins EM_A[20:0] should be
connected to memory address pins [22:2] and EM_BA[1:0] should be connected to
memory addresss pins [1:0]. For 16-bit Asynchronous memory, pins EM_A[20:0]
should be connected to memory address pins [20:1] and EM_BA[1] should be
connected to memory addresss pin [0].
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
Table 2-8. External Memory Interface (EMIF) Terminal Functions (continued)
SIGNAL
PRODUCT PREVIEW
22
TYPE (1)
OTHER (2)
(3)
DESCRIPTION
NAME
NO.
EM_A[2]
E1
I/O/Z
DVDDEMIF
BH
This pin is the EMIF external address pin 2.
EM_A[1]
C2
I/O/Z
DVDDEMIF
BH
This pin is the EMIF external address pin 1.
EM_A[0]
B2
I/O/Z
DVDDEMIF
BH
This pin is the EMIF external address pin 0.
I/O/Z
DVDDEMIF
BH
EMIF 16-bit bi-directional bus.
EM_D[15]
J4
EM_D[14]
K3
EM_D[13]
K4
EM_D[12]
L3
EM_D[11]
C4
EM_D[10]
D3
EM_D[9]
F4
EM_D[8]
E3
EM_D[7]
H3
EM_D[6]
K5
EM_D[5]
M2
EM_D[4]
L4
EM_D[3]
D4
EM_D[2]
F3
EM_D[1]
E5
EM_D[0]
G3
EM_CS5
A3
O/Z
DVDDEMIF
BH
EMIF chip select 5 output for use with asynchronous memories (i.e., NOR flash,
NAND flash, or SRAM).
EM_CS4
C3
O/Z
DVDDEMIF
BH
EMIF chip select 4 output for use with asynchronous memories (i.e., NOR flash,
NAND flash, or SRAM).
EM_CS3
M4
O/Z
DVDDEMIF
BH
EMIF NAND chip select 3 output for use with asynchronous memories (i.e., NOR
flash, NAND flash, or SRAM).
EM_CS2
C5
O/Z
DVDDEMIF
BH
EMIF NAND chip select 2 output for use with asynchronous memories (i.e., NOR
flash, NAND flash, or SRAM).
EM_WE
H1
O/Z
DVDDEMIF
BH
EMIF asynchronous memory write enable output
EM_OE
E4
O/Z
DVDDEMIF
BH
EMIF asynchronous memory read enable output
EM_R/W
B6
O/Z
DVDDEMIF
BH
EMIF asynchronous read/write output
EM_DQM1
P1
O/Z
DVDDEMIF
BH
EMIF asynchronous data write strobes and byte enables or EMIF SDRAM and
mSDRAM data mask bits.
EM_DQM0
B5
O/Z
DVDDEMIF
BH
EM_BA[1]
B1
O/Z
DVDDEMIF
BH
EM_BA[0]
A1
O/Z
DVDDEMIF
BH
EM_WAIT5
H4
I
DVDDEMIF
BH
EMIF wait state extension input 5 for EM_CS5
EM_WAIT4
G1
I
DVDDEMIF
BH
EMIF wait state extension input 4 for EM_CS4
EM_WAIT3
K6
I
DVDDEMIF
BH
EMIF wait state extension input 3 for EM_CS3
EMIF asynchronous bank address
16-bit wide memory: EM_BA[1] forms the device address[0] and BA[0] forms device
address [23].
8-bit wide memory: EM_BA[1] forms the device address[1] and BA[0] forms device
address [0].
EMIF SDRAM and mSDRAM bank address.
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Table 2-8. External Memory Interface (EMIF) Terminal Functions (continued)
SIGNAL
NAME
NO.
EM_WAIT2
D5
TYPE (1)
I
OTHER (2)
(3)
DVDDEMIF
BH
DESCRIPTION
EMIF wait state extension input 2 for EM_CS2
EMIF FUNCTIONAL PINS: SDRAM and mSDRAM ONLY
A4
O/Z
DVDDEMIF
BH
EMIF SDRAM/mSDRAM chip select 1 output
EM_CS0
B3
O/Z
DVDDEMIF
BH
EMIF SDRAM/mSDRAM chip select 0 output
EM_SDCLK
M3
O/Z
DVDDEMIF
BH
EMIF SDRAM/mSDRAM clock
EM_SDCKE
N2
O/Z
DVDDEMIF
BH
EMIF SDRAM/mSDRAM clock enable
EM_SDRAS
A6
O/Z
DVDDEMIF
BH
EMIF SDRAM/mSDRAM row address strobe
EM_SDCAS
B4
O/Z
DVDDEMIF
BH
EMIF SDRAM/mSDRAM column strobe
PRODUCT PREVIEW
EM_CS1
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
23
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
Table 2-9. Inter-Integrated Circuit (I2C) Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
DESCRIPTION
I2C
(1)
(2)
(3)
SCL
B7
I/O/Z
DVDDIO
BH
SDA
B8
I/O/Z
DVDDIO
BH
This pin is the I2C clock output. Per the I2C standard, an external pullup is required
on this pin.
This pin is the I2C bidirectional data signal. Per the I2C standard, an external pullup
is required on this pin.
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, BH = Bus Holder
IPD = Internal pulldown, IPU = Internal pullup. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 3.8.1 , Pullup/Pulldown Resistors.
Specifies the operating I/O supply voltage for each signal
Table 2-10. Inter-IC Sound (I2S0 – I2S3) Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
DESCRIPTION
Interface 0 (I2S0)
PRODUCT PREVIEW
MMC0_D0/
I2S0_DX/
GP[2]
L9
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between MMC0, I2S0, and GPIO.
For I2S, it is I2S0 transmit data output I2S0_DX.
Mux control via the SP0MODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR1 register.
MMC0_CLK/
I2S0_CLK/
GP[0]
L10
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between MMC0, I2S0, and GPIO.
For I2S, it is I2S0 clock input/output I2S0_CLK.
Mux control via the SP0MODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR1 register.
MMC0_D1/
I2S0_RX/
GP[3]
M10
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between MMC0, I2S0, and GPIO.
For I2S, it is I2S0 receive data input I2S0_RX.
Mux control via the SP0MODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR1 register.
MMC0_CMD/
I2S0_FS/
GP[1]
M11
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between MMC0, I2S0, and GPIO.
For I2S, it is I2S0 frame synchronization input/output I2S0_FS.
Mux control via the SP0MODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR1 register.
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between MMC1, I2S1, and GPIO.
For I2S, it is I2S1 transmit data output I2S1_DX.
Mux control via the SP1MODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR1 register.
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between MMC1, I2S1, and GPIO.
For I2S, it is I2S1 clock input/output I2S1_CLK.
Mux control via the SP1MODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR1 register.
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between MMC1, I2S1, and GPIO.
For I2S, it is I2S1 receive data input I2S1_RX.
Mux control via the SP1MODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR1 register.
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed betweenn MMC1, I2S2, and GPIO.
For I2S, it is I2S1 frame synchronization input/output I2S1_FS.
Mux control via the SP1MODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR1 register.
Interface 1 (I2S1)
MMC1_D0/
I2S1_DX/
GP[8]
MMC1_CLK/
I2S1_CLK/
GP[6]
MMC1_D1/
I2S1_RX/
GP[9]
MMC1_CMD/
I2S1_FS/
GP[7]
(1)
(2)
(3)
24
M14
M13
M12
L14
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, BH = Bus Holder
IPD = Internal pulldown, IPU = Internal pullup. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 3.8.1 , Pullup/Pulldown Resistors.
Specifies the operating I/O supply voltage for each signal
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Table 2-10. Inter-IC Sound (I2S0 – I2S3) Terminal Functions (continued)
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
DESCRIPTION
Interface 2 (I2S2)
LCD_D[11]/
I2S2_DX/
GP[27]/
SPI_TX
LCD_D8]/
I2S2_CLK/
GP[18]/
SPI_CLK
P12
N10
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge, I2S2, GPIO, and SPI.
For I2S, it is I2S2 transmit data output I2S2_DX.
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge, I2S2, GPIO, and SPI.
For I2S, it is I2S2 clock input/output I2S2_CLK.
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
This pin is multiplexed between LCD Bridge, I2S2, GPIO, and SPI.
For I2S, it is I2S2 receive data input I2S2_RX.
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
LCD_D[10]/
I2S2_RX/
GP[20]/
SPI_RX
N11
I/O/Z
IPD
DVDDIO
BH
LCD_D[9]/
I2S2_FS/
GP[19]/
SPI_CS0
P11
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge, I2S2, and GPIO.
For I2S, it is I2S2 frame synchronization input/output I2S2_FS.
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
P14
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge, UART, GPIO, and I2S3.
For I2S, it is I2S3 transmit data output I2S3_DX.
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
LCD_D[12]/
UART_RTS/
GP[28]/
I2S3_CLK
N12
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge, UART, GPIO, and I2S3.
For I2S, it is I2S3 clock input/output I2S3_CLK.
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
LCD_D[14]/
UART_RXD/
GP[30]/
I2S3_RX
N13
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge, UART, GPIO, and I2S3.
For I2S, it is I2S3 receive data input I2S3_RX.
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
LCD_D[13]/
UART_CTS/
GP[29]/
I2S3_FS
P13
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge, UART, GPIO, and I2S3.
For I2S, it is I2S3 frame synchronization input/output I2S3_FS.
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
PRODUCT PREVIEW
Interface 3 (I2S3)
LCD_D[15]/
UART_TXD/
GP[31]/
I2S3_DX
25
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
Table 2-11. Serial Peripheral Interface (SPI) Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
DESCRIPTION
Serial Port Interface (SPI)
PRODUCT PREVIEW
LCD_CS0_E0/
SPI_CS0
P4
I/O/Z
DVDDIO
BH
This pin is multiplexed between LCD Bridge and SPI.
Mux control via the PPMODE bits in the EBSR.
For SPI, this pin is SPI chip select SPI_CS0.
LCD_D[9]/
I2S2_FS/
GP[19]/
SPI_CS0
P11
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge, I2S2, GPIO, and SPI.
Mux control via the PPMODE bits in the EBSR.
For SPI, this pin is SPI chip select SPI_CS0.
The IPD resistor on this pin can be enabled or disabled via the PDINHIBR3 register.
LCD_CS1_E1/
SPI_CS1
N4
I/O/Z
DVDDIO
BH
This pin is multiplexed between LCD Bridge and SPI.
Mux control via the PPMODE bits in the EBSR.
For SPI, this pin is SPI chip select SPI_CS1.
LCD_RW_WRB/
SPI_CS2
P5
I/O/Z
DVDDIO
BH
This pin is multiplexed between LCD Bridge and SPI.
Mux control via the PPMODE bits in the EBSR.
For SPI, this pin is SPI chip select SPI_CS2.
LCD_RS/
SPI_CS3
N5
I/O/Z
DVDDIO
BH
This pin is multiplexed between LCD Bridge and SPI.
Mux control via the PPMODE bits in the EBSR.
For SPI, this pin is SPI chip select SPI_CS3.
LCD_EN_RDB/
SPI_CLK
N3
O/Z
DVDDIO
BH
This pin is multiplexed between LCD Bridge and SPI.
Mux control via the PPMODE bits in the EBSR.
For SPI, this pin is clock output SPI_CLK.
This pin is multiplexed between LCD Bridge, I2S2, GPIO, and SPI.
Mux control via the PPMODE bits in the EBSR.
For SPI, this pin is clock output SPI_CLK.
The IPD resistor on this pin can be enabled or disabled via the PDINHIBR3 register.
(1)
(2)
(3)
26
LCD_D8]/
I2S2_CLK/
GP[18]/
SPI_CLK
N10
I/O/Z
IPD
DVDDIO
BH
LCD_D[1]/
SPI_TX
N6
I/O/Z
DVDDIO
BH
This pin is multiplexed between LCD Bridge and SPI.
Mux control via the PPMODE bits in the EBSR.
For SPI, this pin is SPI transmit data output.
LCD_D[11]/
I2S2_DX/
GP[27]/
SPI_TX
P12
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge, I2S2, GPIO, and SPI.
Mux control via the PPMODE bits in the EBSR.
For SPI, this pin is SPI transmit data output.
The IPD resistor on this pin can be enabled or disabled via the PDINHIBR3 register.
LCD_D[0]/
SPI_RX
P6
I/O/Z
DVDDIO
BH
This pin is multiplexed between LCD Bridge and SPI.
Mux control via the PPMODE bits in the EBSR.
For SPI this pin is SPI receive data input.
LCD_D[10]/
I2S2_RX/
GP[20]/
SPI_RX
N11
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge, I2S2, GPIO, and SPI.
Mux control via the PPMODE bits in the EBSR.
For SPI this pin is SPI receive data input.
The IPD resistor on this pin can be enabled or disabled via the PDINHIBR3 register.
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, BH = Bus Holder
IPD = Internal pulldown, IPU = Internal pullup. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 3.8.1 , Pullup/Pulldown Resistors.
Specifies the operating I/O supply voltage for each signal
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Table 2-12. UART Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
DESCRIPTION
LCD_D[15]/
UART_TXD/
GP[31]/
I2S3_DX
LCD_D[13]/
UART_CTS/
GP[29]/
I2S3_FS
LCD_D[12]/
UART_RTS/
GP[28]/
I2S3_CLK
(1)
(2)
(3)
N13
P14
P13
N12
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge, UART, GPIO, and I2S3.
When used by UART, it is the receive data input UART_RXD.
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge, UART, GPIO, and I2S3.
In UART mode, it is the transmit data output UART_TXD.
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge, UART, GPIO, and I2S3.
In UART mode, it is the clear to send input UART_CTS.
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge, UART, GPIO, and I2S3.
In UART mode, it is the ready to send output UART_RTS.
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, BH = Bus Holder
IPD = Internal pulldown, IPU = Internal pullup. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 3.8.1 , Pullup/Pulldown Resistors.
Specifies the operating I/O supply voltage for each signal
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
27
PRODUCT PREVIEW
UART
LCD_D[14]/
UART_RXD/
GP[30]/
I2S3_RX
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
Table 2-13. USB2.0 Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
DESCRIPTION
USB 2.0
12-MHz crystal oscillator input.
USB_MXI
G13
I
USB_VDDOSC
USB_MXO
G14
O
USB_VDDOSC
When the USB peripheral is not used, USB_MXI should be connected to ground
(VSS).
12-MHz crystal oscillator output.
When the USB peripheral is not used, USB_MXO should be left unconnected.
3.3-V power supply for USB oscillator.
PRODUCT PREVIEW
USB_VDDOSC
G12
S
see
Section 4.2,
ROC
USB_VSSOSC
F11
S
see
Section 4.2,
ROC
Ground for USB oscillator.
USB_VBUS
J12
A I/O
see
Section 4.2,
ROC
USB power detect. 5-V input that signifies that VBUS is connected.
When the USB peripheral is not used, the USB_VBUS signal should be connected
to ground (VSS).
USB_DP
H14
A I/O
USB_VDDA3P3
USB bi-directional Data Differential signal pair [positive/negative].
USB_DM
J14
A I/O
USB_VDDA3P3
When the USB peripheral is not used, the USB_DP and USB_DM signals should
both be tied to ground (VSS).
USB_R1
G9
A I/O
USB_VDDA3P3
When the USB peripheral is not used, USB_VDDOSC should be connected to ground
(VSS).
External resistor connect. Reference current output. This must be connected via a
10-kΩ ±1% resistor to USB_VSSREF and be placed as close to the device as
possible.
When the USB peripheral is not used, the USB_R1 signal should be connected via
a 10-kΩ resistor to USB_VSSREF.
(1)
(2)
(3)
28
Ground for reference current. This must be connected via a 10-kΩ ±1% resistor to
USB_R1.
When the USB peripheral is not used, the USB_VSSREF signal should be connected
directly to ground (Vss).
USB_VSSREF
G10
GND
see
Section 4.2,
ROC
USB_VDDA3P3
H12
S
see
Section 4.2,
ROC
USB_VSSA3P3
H11
GND
see
Section 4.2,
ROC
USB_VDDA1P3
H10
S
see
Section 4.2,
ROC
USB_VSSA1P3
H9
GND
see
Section 4.2,
ROC
USB_VDD1P3
J13
S
see
Section 4.2,
ROC
USB_VSS1P3
H13
GND
see
Section 4.2,
ROC
Digital core ground for USB phy.
USB_VDDPLL
G8
S
see
Section 4.2,
ROC
3.3 V USB Analog PLL power supply.
When the USB peripheral is not used, the USB_VDDPLL signal should be connected
to ground (VSS).
Analog 3.3 V power supply for USB PHY.
When the USB peripheral is not used, the USB_VDDA3P3 signal should be
connected to ground (VSS).
Analog ground for USB PHY.
Analog 1.3 V power supply for USB PHY. [For high-speed sensitive analog circuits]
When the USB peripheral is not used, the USB_VDDA1P3 signal should be
connected to ground (VSS).
Analog ground for USB PHY [For high speed sensitive analog circuits].
1.3-V digital core power supply for USB PHY.
When the USB peripheral is not used, the USB_VDD1P3 signal should be connected
to ground (VSS).
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, BH = Bus Holder
IPD = Internal pulldown, IPU = Internal pullup. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 3.8.1 , Pullup/Pulldown Resistors.
Specifies the operating I/O supply voltage for each signal
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Table 2-13. USB2.0 Terminal Functions (continued)
SIGNAL
NO.
USB_VSSPLL
G11
TYPE (1)
GND
OTHER (2)
(3)
see
Section 4.2,
ROC
DESCRIPTION
USB Analog PLL ground.
PRODUCT PREVIEW
NAME
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
29
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
Table 2-14. LCD Bridge Terminal Functions
SIGNAL
TYPE (1)
OTHER (2)
(3)
DESCRIPTION
NO.
LCD_EN_RDB/
SPI_CLK
N3
O/Z
DVDDIO
BH
This pin is multiplexed between LCD Bridge and SPI.
For LCD Bridge, this pin is either LCD Bridge read/write enable (MPU68 mode) or
read strobe (MPU80 mode).
Mux control via the PPMODE bits in the EBSR.
LCD_CS0_E0/
SPI_CS0
P4
I/O/Z
DVDDIO
BH
This pin is multiplexed between LCD Bridge and SPI.
For LCD Bridge, this pin is either LCD Bridge chip select 0 (MPU68 and MPU80
modes) or enable 0 (HD44780 mode).
Mux control via the PPMODE bits in the EBSR.
LCD_CS1_E1/
SPI_CS1
N4
I/O/Z
DVDDIO
BH
This pin is multiplexed between LCD Bridge and SPI.
For LCD Bridge, this pin is either LCD Bridge chip select 1 (MPU68 and MPU80
modes) or enable 1 (HD44780 mode).
Mux control via the PPMODE bits in the EBSR.
LCD_RW_WRB/
SPI_CS2
P5
I/O/Z
DVDDIO
BH
This pin is multiplexed between LCD Bridge and SPI.
For LCD, this pin is either LCD Bridge read/write select (HD44780 and MPU68
modes) or write strobe (MPU80 mode).
Mux control via the PPMODE bits in the EBSR,.
LCD_RS/
SPI_CS3
N5
I/O/Z
DVDDIO
BH
This pin is multiplexed between LCD Bridge and SPI.
For LCD, this pin is the LCD Bridge address set-up.
Mux control via the PPMODE bits in the EBSR.
LCD_D[15]/
UART_TXD/
GP[31]/
I2S3_DX
P14
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge, UART, GPIO, and I2S3.
For LCD Bridge, it is LCD data pin 15.
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
LCD_D[14]/
UART_RXD/
GP[30]/
I2S3_RX
N13
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge, UART, GPIO, and I2S3.
For LCD Bridge, it is LCD data pin 14.
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
LCD_D[13]/
UART_CTS/
GP[29]/
I2S3_FS
P13
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge, UART, GPIO, and I2S3.
For LCD Bridge, it is LCD data pin 13.
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
LCD_D[12]/
UART_RTS/
GP[28]/
I2S3_CLK
N12
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge, I2S2, and GPIO.
For LCD Bridge, it is LCD data pin 12.
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
LCD_D[11]/
I2S2_DX/
GP[27]/
SPI_TX
P12
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge, I2S2, GPIO, and SPI.
For LCD Bridge, it is LCD data pin 11.
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
LCD_D[10]/
I2S2_RX/
GP[20]/
SPI_RX
N11
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge, I2S2, GPIO, and SPI.
For LCD Bridge, it is LCD data pin 10.
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
LCD_D[9]/
I2S2_FS/
GP[19]/
SPI_CS0
P11
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge, I2S2, GPIO, and SPI.
For LCD Bridge, it is LCD data pin 9.
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge, I2S2, GPIO, and SPI.
For LCD Bridge, it is LCD data pin 8.
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge and GPIO.
For LCD Bridge, it is LCD data pin 7.
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
PRODUCT PREVIEW
NAME
LCD_D[8]/
I2S2_CLK
GP[18]/
SPI_CLK
LCD_D[7]/
GP[17]
(1)
(2)
(3)
30
N10
P10
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, BH = Bus Holder
IPD = Internal pulldown, IPU = Internal pullup. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 3.8.1 , Pullup/Pulldown Resistors.
Specifies the operating I/O supply voltage for each signal
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Table 2-14. LCD Bridge Terminal Functions (continued)
TYPE (1)
OTHER (2)
(3)
DESCRIPTION
NAME
NO.
LCD_D[6]/
GP[16]
N9
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge and GPIO.
For LCD Bridge, it is LCD data pin 6.
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
LCD_D[5]/
GP[15]
P9
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge and GPIO.
For LCD Bridge, it is LCD data pin 5.
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge and GPIO.
For LCD Bridge, it is LCD data pin 4.
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge and GPIO.
For LCD Bridge, it is LCD data pin 3.
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
This pin is multiplexed between LCD Bridge and GPIO.
For LCD Bridge, it is LCD data pin 2.
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
LCD_D[4]/
GP[14]
LCD_D[3]/
GP[13]
N8
N7
LCD_D[2]/
GP[12]
P7
I/O/Z
IPD
DVDDIO
BH
LCD_D[1]/
SPI_TX
N6
I/O/Z
DVDDIO
BH
This pin is multiplexed between LCD Bridge and SPI.
For LCD Bridge, it is LCD data pin 1.
Mux control via the PPMODE bits in the EBSR.
LCD_D[0]/
SPI_RX
P6
I/O/Z
DVDDIO
BH
This pin is multiplexed between LCD Bridge and SPI.
For LCD Bridge, it is LCD data pin 0.
Mux control via the PPMODE bits in the EBSR.
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
PRODUCT PREVIEW
SIGNAL
31
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
Table 2-15. MMC1/SD Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
DESCRIPTION
MMC/SD
MMC1_CLK/
I2S1_CLK/
GP[6]
PRODUCT PREVIEW
(1)
(2)
(3)
M13
O
IPD
DVDDIO
BH
This pin is multiplexed between MMC1, I2S1, and GPIO.
For MMC/SD, this is the MMC1 data clock output MMC1_CLK.
Mux control via the SP1MODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR1 register.
This pin is multiplexed between MMC1, I2S1, and GPIO.
For MMC/SD, this is the MMC1 command I/O output MMC1_CMD.
Mux control via the SP1MODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR1 register.
MMC1_CMD/
I2S1_FS/
GP[7]
L14
O
IPD
DVDDIO
BH
MMC1_D3/
GP[11]
L13
I/O/Z
IPD
DVDDIO
BH
MMC1_D2/
GP[10]
K14
I/O/Z
IPD
DVDDIO
BH
MMC1_D1/
I2S1_RX/
GP[9]
M12
I/O/Z
IPD
DVDDIO
BH
MMC1_D0/
I2S1_DX/
GP[8]
M14
I/O/Z
IPD
DVDDIO
BH
The MMC1_D3 and MMC1_D2 pins are multiplexed between MMC1 and GPIO.
The MMC1_D1 and MMC1_D0 pins are multiplexed between MMC1, I2S1, and
GPIO.
In MMC/SD mode, all these pins are the MMC1 nibble wide bi-directional data bus.
Mux control via the SP1MODE bits in the EBSR.
The IPD resistor on these pins can be enabled or disabled via the PDINHIBR1
register.
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, BH = Bus Holder
IPD = Internal pulldown, IPU = Internal pullup. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 3.8.1 , Pullup/Pulldown Resistors.
Specifies the operating I/O supply voltage for each signal
Table 2-16. MMC0/SD Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
DESCRIPTION
MMC/SD
(1)
(2)
(3)
32
MMC0_CLK/
I2S0_CLK/
GP[0]
L10
O
IPD
DVDDIO
BH
This pin is multiplexed between MMC0, I2S0, and GPIO.
For MMC/SD, this is the MMC0 data clock output MMC0_CLK.
Mux control via the SP0MODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR1 register.
MMC0_CMD/
I2S0_FS/
GP[1]
M11
O
IPD
DVDDIO
BH
This pin is multiplexed between MMC0, I2S0, and GPIO.
For MMC/SD, this is the MMC0 command I/O output MMC0_CMD.
Mux control via the SP0MODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR1 register.
MMC0_D3/
GP[5]
L11
I/O/Z
IPD
DVDDIO
BH
MMC0_D2/
GP[4]
L12
I/O/Z
IPD
DVDDIO
BH
MMC0_D1/
I2S0_RX/
GP[3]
M10
I/O/Z
IPD
DVDDIO
BH
MMC0_D0/
I2S0_DX/
GP[2]
L9
I/O/Z
IPD
DVDDIO
BH
The MMC0_D3 and MMC0_D2 pins are multiplexed between MMC0 and GPIO.
The MMC0_D1 and MMC0_D0 pins are multiplexed between MMC0, I2S0, and
GPIO.
In MMC/SD mode, these pins are the MMC0 nibble wide bi-directional data bus.
Mux control via the SP0MODE bits in the EBSR.
The IPD resistor on these pins can be enabled or disabled via the PDINHIBR1
register.
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, BH = Bus Holder
IPD = Internal pulldown, IPU = Internal pullup. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 3.8.1 , Pullup/Pulldown Resistors.
Specifies the operating I/O supply voltage for each signal
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Table 2-17. 10-Bit SAR ADC Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
DESCRIPTION
GPAIN0
GPAIN1
GPAIN2
GPAIN3
(1)
(2)
(3)
D10
A11
B11
C11
I/O
I/O
I/O
I/O
VDDA_ANA
VDDA_ANA
GPAIN1: General -Purpose Output and Analog Input pin 1. This pin is connected to
ADC Channel 3. GPAIN1 can be used as a general-purpose output if certain
requirements are met (see Note: below). GPAIN1 can accommodate input voltages
from 0 V to VDDA_ANA.
Note: If the ANA_LDO is used to supply power to VDDA_ANA, this pin must not be
used as a general-purpose output (driving high) since the max current capability
(see the ISD parameter in Section 4.3, Electrical Characteristics Over Recommended
Ranges of Supply Voltage and Operating Temperature) of the ANA_LDO can be
exceeded. Doing so may result in the on-chip power-on reset (POR) resetting the
chip.
VDDA_ANA
GPAIN2: General -Purpose Output and Analog Input pin 2. This pin is connected to
ADC Channel 4. GPAIN2 can be used as a general-purpose output if certain
requirements are met (see Note: below). GPAIN2 can accommodate input voltages
from 0 V to VDDA_ANA.
Note: If the ANA_LDO is used to supply power to VDDA_ANA, this pin must not be
used as a general-purpose output (driving high) since the max current capability
(see the ISD parameter in Section 4.3, Electrical Characteristics Over Recommended
Ranges of Supply Voltage and Operating Temperature) of the ANA_LDO can be
exceeded. Doing so may result in the on-chip POR resetting the chip.
VDDA_ANA
GPAIN3: General -Purpose Output and Analog Input pin 3. This pin is connected to
ADC Channel 5. GPAIN3 can be used as a general-purpose output if certain
requirements are met (see Note: below). GPAIN3 can accommodate input voltages
from 0 V to VDDA_ANA.
Note: If the ANA_LDO is used to supply power to VDDA_ANA, this pin must not be
used as a general-purpose output (driving high) since the max current capability
(see the ISD parameter in Section 4.3, Electrical Characteristics Over Recommended
Ranges of Supply Voltage and Operating Temperature) of the ANA_LDO can be
exceeded. Doing so may result in the on-chip POR resetting the chip.
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, BH = Bus Holder
IPD = Internal pulldown, IPU = Internal pullup. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 3.8.1 , Pullup/Pulldown Resistors.
Specifies the operating I/O supply voltage for each signal
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
33
PRODUCT PREVIEW
SAR ADC
GPAIN0: General -Purpose Output and Analog Input pin 0. This pin is demuxed
internally into ADC Channels 0, 1, & 2. GPAIN0 can also be used as a
general-purpose open-drain output. This pin is unique among the GPAIN pins in that
it is the only pin that is 3.6 V-tolerant to support measuring a battery voltage.
GPAIN0 can accommodate input voltages from 0 V to 3.6 V; although, the ADC is
unable to accept signals greater than VDDA_ANA without clamping. ADC Channel 1 is
capable of switching in an internal resistor divider that has a divide ratio of
approximately 1/8.
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
Table 2-18. GPIO Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
DESCRIPTION
General-Purpose Input/Output
External Flag Output. XF is used for signalling other processors in multiprocessor
configurations or XF can be used as a fast general-purpose output pin.
XF
MMC0_CLK/
I2S0_CLK/
GP[0]
MMC0_CMD/
I2S0_FS/
GP[1]
MMC0_D0/
I2S0_DX/
GP[2]
PRODUCT PREVIEW
MMC0_D1/
I2S0_RX/
GP[3]
MMC0_D2/
GP[4]
L9
M10
L12
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between MMC0, I2S0, and GPIO.
For GPIO, it is general-purpose input/output pin 0 (GP[0]).
Mux control via the SP0MODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR1 register.
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between MMC0, I2S0, and GPIO.
For GPIO, it is general-purpose input/output pin 1 (GP[1]).
Mux control via the SP0MODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR1 register.
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between MMC0, I2S0, and GPIO.
For GPIO, it is general-purpose input/output pin 2 (GP[2]).
Mux control via the SP0MODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR1 register.
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between MMC0, I2S0, and GPIO.
For GPIO, it is general-purpose input/output pin 3 (GP[3]).
Mux control via the SP0MODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR1 register.
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between MMC0 and GPIO.
For GPIO, it is general-purpose input/output pin 4 (GP[4]).
Mux control via the SP0MODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR1 register.
This pin is multiplexed between MMC0 and GPIO.
For GPIO, it is general-purpose input/output pin 5 (GP[5]).
Mux control via the SP0MODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR1 register.
XF is set high by the BSET XF instruction and XF is set low by the BCLR XF
instruction or by writing to bit 13 of the ST1_55 register. At reset, the XF pin will be
high. For more information on the ST1_55 register, see the TMS320C55x 3.0 CPU
Reference Guide (literature number: SWPU073).
L11
I/O/Z
MMC1_CLK/
I2S1_CLK/
GP[6]
M13
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between MMC1, I2S1, and GPIO.
For GPIO, it is general-purpose input/output pin 6 (GP[6]).
Mux control via the SP1MODE bits in the EBSR.
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between MMC1, I2S1, and GPIO.
For GPIO, it is general-purpose input/output pin 7 (GP[7]).
Mux control via the SP1MODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR1 register.
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between MMC1, I2S1, and GPIO.
For GPIO, it is general-purpose input/output pin 8 (GP[8]).
Mux control via the SP1MODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR1 register.
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between MMC1, I2S1, and GPIO.
For GPIO, it is general-purpose input/output pin 9 (GP[9]).
Mux control via the SP1MODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR1 register.
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between MMC1 and GPIO.
For GPIO, it is general-purpose input/output pin 10 (GP[10]).
Mux control via the SP1MODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR1 register.
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between MMC1 and GPIO.
For GPIO, it is general-purpose input/output pin 11 (GP[11]).
Mux control via the SP1MODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR1 register.
MMC1_D1/
I2S1_RX/
GP[9]
MMC1_D2/
GP[10]
MMC1_D3/
GP[11]
34
M11
–
DVDDIO
BH
IPD
DVDDIO
BH
MMC1_D0/
I2S1_DX/
GP[8]
(3)
L10
O/Z
MMC0_D3/
GP[5]
MMC1_CMD/
I2S1_FS/
GP[7]
(1)
(2)
M8
L14
M14
M12
K14
L13
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, BH = Bus Holder
IPD = Internal pulldown, IPU = Internal pullup. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 3.8.1 , Pullup/Pulldown Resistors.
Specifies the operating I/O supply voltage for each signal
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Table 2-18. GPIO Terminal Functions (continued)
TYPE (1)
OTHER (2)
(3)
DESCRIPTION
NAME
NO.
LCD_D[2]/
GP[12]
P7
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge and GPIO.
For GPIO, it is general-purpose input/output pin 12 (GP[12]).
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
LCD_D[3]/
GP[13]
N7
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge and GPIO.
For GPIO, it is general-purpose input/output pin 13 (GP[13]).
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge and GPIO.
For GPIO, it is general-purpose input/output pin 14 (GP[14]).
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge and GPIO.
For GPIO, it is general-purpose input/output pin 15 (GP[15]).
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge and GPIO.
For GPIO, it is general-purpose input/output pin 16 (GP[16]).
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge and GPIO.
For GPIO, it is general-purpose input/output pin 17 (GP[17]).
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge and GPIO.
For GPIO, it is general-purpose input/output pin 18 (GP[18]).
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge, I2S2, and GPIO.
For GPIO, it is general-purpose input/output pin 19 (GP[19]).
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
This pin is multiplexed between LCD Bridge, I2S2, GPIOand SPI.
For GPIO, it is general-purpose input/output pin 20 (GP[20]).
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
LCD_D[4]/
GP[14]
LCD_D[5]/
GP[15]
LCD_D[6]/
GP[16]
LCD_D[7]/
GP[17]
LCD_D8]/
I2S2_CLK/
GP[18]/
SPI_CLK
LCD_D[9]/
I2S2_FS/
GP[19]/
SPI_CS0
N8
P9
N9
P10
N10
P11
LCD_D[10]/
I2S2_RX/
GP[20]/
SPI_RX
N11
I/O/Z
IPD
DVDDIO
BH
EM_A[15]/GP[21]
N1
I/O/Z
IPD
DVDDEMIF
BH
This pin is multiplexed between EMIF and GPIO.
For GPIO, it is general-purpose input/output pin 21 (GP[21]).
Mux control via the A15_MODE bit in the EBSR.
The IPD resistor on this pin can be enabled or disabled via the PDINHIBR2 register.
EM_A[16]/GP[22]
E2
I/O/Z
IPD
DVDDEMIF
BH
This pin is multiplexed between EMIF and GPIO.
For GPIO, it is general-purpose input/output pin 22 (GP[22]).
Mux control via the A16_MODE bit in the EBSR.
The IPD resistor on this pin can be enabled or disabled via the PDINHIBR2 register.
EM_A[17]/GP[23]
F2
I/O/Z
IPD
DVDDEMIF
BH
This pin is multiplexed between EMIF and GPIO.
For GPIO, it is general-purpose input/output pin 23 (GP[23]).
Mux control via the A17_MODE bit in the EBSR.
The IPD resistor on this pin can be enabled or disabled via the PDINHIBR2 register.
EM_A[18]/GP[24]
G2
I/O/Z
IPD
DVDDEMIF
BH
This pin is multiplexed between EMIF and GPIO.
For GPIO, it is general-purpose input/output pin 24 (GP[24]).
Mux control via the A18_MODE bit in the EBSR.
The IPD resistor on this pin can be enabled or disabled via the PDINHIBR2 register.
EM_A[19]/GP[25]
G4
I/O/Z
IPD
DVDDEMIF
BH
This pin is multiplexed between EMIF and GPIO.
For GPIO, it is general-purpose input/output pin 25 (GP[25]).
Mux control via the A19_MODE bit in the EBSR.
The IPD resistor on this pin can be enabled or disabled via the PDINHIBR2 register.
EM_A[20]/GP[26]
J3
I/O/Z
IPD
DVDDEMIF
BH
This pin is multiplexed between EMIF and GPIO.
For GPIO, it is general-purpose input/output pin 26 (GP[26]).
Mux control via the A20_MODE bit in the EBSR.
The IPD resistor on this pin can be enabled or disabled via the PDINHIBR2 register.
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
35
PRODUCT PREVIEW
SIGNAL
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
Table 2-18. GPIO Terminal Functions (continued)
SIGNAL
OTHER (2)
(3)
DESCRIPTION
NO.
LCD_D[11]/
I2S2_DX/
GP[27]/
SPI_TX
P12
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge, I2S2, GPIO, and SPI.
For GPIO, it is general-purpose input/output pin 27 (GP[27]).
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
LCD_D[12]/
UART_RTS/
GP[28]/
I2S3_CLK
N12
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge, UART, GPIO, and I2S3.
For GPIO, it is general-purpose input/output pin 28 (GP[28]).
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge, UART, GPIO, and I2S3.
For GPIO, it is general-purpose input/output pin 29 (GP[29]).
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge, UART, GPIO, and I2S3.
For GPIO, it is general-purpose input/output pin 30 (GP[30]).
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
I/O/Z
IPD
DVDDIO
BH
This pin is multiplexed between LCD Bridge, UART, GPIO, and I2S3.
For GPIO, it is general-purpose input/output pin 31 (GP[31]).
Mux control via the PPMODE bits in the EBSR. The IPD resistor on this pin can be
enabled or disabled via the PDINHIBR3 register.
LCD_D[13]/
UART_CTS/
GP[29]/
I2S3_FS
LCD_D[14]/
UART_RXD/
GP[30]/
I2S3_RX
PRODUCT PREVIEW
LCD_D[15]/
UART_TXD/
GP[31]/
I2S3_DX
36
TYPE (1)
NAME
P13
N13
P14
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Table 2-19. Regulators and Power Management Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
DESCRIPTION
DSP_LDOO
E10
LDOI
F14,
F13,
B12
DSP_LDO_EN
USB_LDOO
ANA_LDOO
BG_CAP
(1)
(2)
(3)
D12
F12
A12
B13
S
S
LDO inputs. The LDOI pins must be connected to the same power supply source
with a voltage range of 1.8 V to 3.6 V. These pins supply power to the internal
LDOs, the bandgap reference generator circuits, and serve as the I/O supply for
some input pins.
I
DSP_LDO enable input. This signal is not intended to be dynamically switched.
0 = DSP_LDO is enabled. The internal POR monitors the DSP_LDOO pin voltage
and generates the internal POWERGOOD signal.
1 = DSP_LDO is disabled. The internal POR voltage monitoring is also disabled.
The internal POWERGOOD signal is forced high and the external reset signal on
the RESET pin (D6) is the only source of the device reset. Note, C5505 device's
internal reset signal is generated as the AND of the RESET pin and the internal
POWERGOOD signal.
–
LDOI
S
USB_LDO output. This output provides a regulated 1.3 V output and up to TBD mA
of current (see the ISD parameter in Section 4.3, Electrical Characteristics Over
Recommended Ranges of Supply Voltage and Operating Temperature). For proper
device operation, this pin must be connected to a 1 mF ~ 2 mF decoupling capacitor
to VSS. For more detailed information, see Section 5.3.4, Power-Supply Decoupling.
This LDO is intended to supply power to the USB_ VDD1P3, USB_VDDA1P3 pins and
not external devices.
S
ANA_LDO output. This output provides a regulated 1.3 V output and up to TBD mA
of current (see the ISD parameter in Section 4.3, Electrical Characteristics Over
Recommended Ranges of Supply Voltage and Operating Temperature).
For proper device operation, this pin must be connected to an ~ 1.0 mF decoupling
capacitor to VSS. For more detailed information, see Section 5.3.4, Power-Supply
Decoupling. This LDO is intended to supply power to the VDDA_ANA and VDDA_PLL
pins and not external devices.
O
Bandgap reference filter signal. For proper device operation, this pin needs to be
bypassed with a 0.1 mF capacitor to analog ground (VSSA_ANA).
This external capacitor provides filtering for stable reference voltages & currents
generated by the bandgap circuit. The bandgap produces the references for use by
the System PLL, SAR, and POR circuits.
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, BH = Bus Holder
IPD = Internal pulldown, IPU = Internal pullup. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 3.8.1 , Pullup/Pulldown Resistors.
Specifies the operating I/O supply voltage for each signal
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
37
PRODUCT PREVIEW
Regulators
DSP_LDO output. When enabled, this output provides a regulated 1.3 V or 1.05 V
output and up to TBD mA of current (see the ISD parameter in Section 4.3, Electrical
Characteristics Over Recommended Ranges of Supply Voltage and Operating
Temperature). The DSP_LDO is intended to supply current to the digital core circuits
only (CVDD) and not external devices For proper device operation, the external
decoupling capacitor of this pin should be 5uF ~ 10uF. For more detailed
information, see Section 5.3.4, Power-Supply Decoupling.
When disabled, this pin is in the high-impedance (Hi-Z) state.
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
Table 2-20. Reserved and No Connects Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
DESCRIPTION
Reserved
(1)
(2)
(3)
RSV0
C12
I
RSV1
J10
PWR
RSV2
J11
PWR
–
LDOI
Reserved. For proper device operation, this pin must be tied directly to VSS.
Reserved. For proper device operation, this pin must be tied directly to CVDD.
Reserved. For proper device operation, this pin must be tied directly to CVDD.
RSV3
D14
I
–
LDOI
RSV4
C14
I
–
LDOI
Reserved. For proper device operation, this pin must be tied directly to VSS.
RSV5
C13
I
–
LDOI
Reserved. For proper device operation, this pin must be tied directly to VSS.
RSV16
D13
I
–
LDOI
Reserved. For proper device operation, this pin must be directly tied to either VSS or
LDOI or tied via a 10-kΩ resistor to either VSS or LDOI.
Reserved. For proper device operation, this pin must be tied directly to VSS.
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, BH = Bus Holder
IPD = Internal pulldown, IPU = Internal pullup. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 3.8.1 , Pullup/Pulldown Resistors.
Specifies the operating I/O supply voltage for each signal
PRODUCT PREVIEW
Table 2-21. Supply Voltage Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
DESCRIPTION
SUPPLY VOLTAGES
F6
H8
CVDD
J6
PWR
1.05-V Digital Core supply voltage (60 or 75 MHz)
1.3-V Digital Core supply voltage (100 or 120 MHz)
PWR
1.8-V, 2.5-V, 2.8-V, or 3.3-V I/O power supply for non-EMIF and non-RTC I/Os
PWR
1.8-V, 2.5-V, 2.8-V, or 3.3-V EMIF I/O power supply
K10
L5
F7
K7
DVDDIO
K12
N14
P3
P8
A2
A5
E6
F5
DVDDEMIF
G5
H5
H7
J5
P2
(1)
(2)
(3)
38
CVDDRTC
C8
PWR
1.05-V thru 1.3-V RTC digital core and RTC oscillator power supply.
DVDDRTC
F8
PWR
1.8-V, 2.5-V, 2.8-V, or 3.3-V I/O power supply for RTC_CLOCKOUT and WAKEUP
pins.
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, BH = Bus Holder
IPD = Internal pulldown, IPU = Internal pullup. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 3.8.1 , Pullup/Pulldown Resistors.
Specifies the operating I/O supply voltage for each signal
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Table 2-21. Supply Voltage Terminal Functions (continued)
TYPE (1)
OTHER (2)
(3)
DESCRIPTION
NAME
NO.
VDDA_PLL
C10
PWR
see
Section 4.2,
ROC
1.3-V Analog PLL power supply for the system clock generator.
USB_VDDPLL
G8
S
see
Section 4.2,
ROC
3.3 V USB Analog PLL power supply.
When the USB peripheral is not used, the USB_VDDPLL signal should be connected
to ground (VSS).
J13
S
see
Section 4.2,
ROC
1.3-V digital core power supply for USB PHY.
USB_VDD1P3
H10
S
see
Section 4.2,
ROC
Analog 1.3 V power supply for USB PHY. [For high-speed sensitive analog circuits]
USB_VDDA1P3
H12
S
see
Section 4.2,
ROC
Analog 3.3 V power supply for USB PHY.
USB_VDDA3P3
G12
S
see
Section 4.2,
ROC
3.3-V power supply for USB oscillator.
USB_VDDOSC
VDDA_ANA
A10
PWR
When the USB peripheral is not used, the USB_VDD1P3 signal should be connected
to ground (VSS).
When the USB peripheral is not used, the USB_VDDA1P3 signal should be
connected to ground (VSS).
When the USB peripheral is not used, the USB_VDDA3P3 signal should be
connected to ground (VSS).
When the USB peripheral is not used, USB_VDDOSC should be connected to
ground (VSS).
1.3-V supply for power management and 10-bit SAR ADC
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
39
PRODUCT PREVIEW
SIGNAL
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
Table 2-22. Ground Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
DESCRIPTION
A13
A14
D7
D11
E9
E11
E12
E13
E14
F9
VSS
F10
GND
Ground pins
G6
G7
H6
J7
PRODUCT PREVIEW
J8
J9
K8
K9
K11
K13
VSS_RTC
40
Ground pin for RTC digital core and RTC oscillator power supply.
VSSA_PLL
D9
GND
USB_VSSPLL
G11
GND
see
Section 4.2,
ROC
USB Analog PLL ground.
USB_VSS1P3
H13
GND
see
Section 4.2,
ROC
Digital core ground for USB phy.
USB_VSSA1P3
H9
GND
see
Section 4.2,
ROC
Analog ground for USB PHY [For high speed sensitive analog circuits].
USB_VSSA3P3
H11
GND
see
Section 4.2,
ROC
Analog ground for USB PHY.
USB_VSSOSC
F11
S
see
Section 4.2,
ROC
Ground for USB oscillator.
GND
see
Section 4.2,
ROC
Ground for reference current. This must be connected via a 10-kΩ ±1% resistor to
USB_R1.
When the USB peripheral is not used, the USB_VSSREF signal should be connected
directly to ground (Vss).
VSSA_ANA
(3)
GND
see
Section 4.2,
ROC
USB_VSSREF
(1)
(2)
C9
G10
B10
B14
GND
Analog PLL ground for the system clock generator.
Ground pins for power management (POR & Bandgap circuits) and 10-bit SAR ADC
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, BH = Bus Holder
IPD = Internal pulldown, IPU = Internal pullup. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 3.8.1 , Pullup/Pulldown Resistors.
Specifies the operating I/O supply voltage for each signal
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
2.6
2.6.1
SPRS645 – JANUARY 2010
Device Support
Development Support
TI offers an extensive line of development tools for the TMS320C55x DSP platform, including tools to
evaluate the performance of the processors, generate code, develop algorithm implementations, and fully
integrate and debug software and hardware modules. The tool's support documentation is electronically
available within the Code Composer Studio™ Integrated Development Environment (IDE).
The following products support development of TMS320C55x fixed-point DSP-based applications:
Hardware Development Tools:
Extended Development System (XDS™) Emulator
For a complete listing of development-support tools for the TMS320C55x DSP platform, visit the Texas
Instruments web site on the Worldwide Web at http://www.ti.com uniform resource locator (URL). For
information on pricing and availability, contact the nearest TI field sales office or authorized distributor.
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
41
PRODUCT PREVIEW
Software Development Tools:
Code Composer Studio™ Integrated Development Environment (IDE): Version 3.3 or later
C/C++/Assembly Code Generation, and Debug plus additional development tools
Scalable, Real-Time Foundation Software (DSP/BIOS™ Version 5.33 or later), which provides the
basic run-time target software needed to support any DSP application.
TMS320C5515
SPRS645 – JANUARY 2010
2.6.2
www.ti.com
Device and Development-Support Tool Nomenclature
To designate the stages in the product development cycle, TI assigns prefixes to the part numbers of all
DSP devices and support tools. Each DSP commercial family member has one of three prefixes: TMX,
TMP, or TMS (e.g.,TMS320C5515AZCHA12). Texas Instruments recommends two of three possible prefix
designators for its support tools: TMDX and TMDS. These prefixes represent evolutionary stages of
product development from engineering prototypes (TMX/TMDX) through fully qualified production
devices/tools (TMS/TMDS).
Device development evolutionary flow:
TMX
Experimental device that is not necessarily representative of the final device's electrical
specifications.
TMP
Final silicon die that conforms to the device's electrical specifications but has not completed
quality and reliability verification.
TMS
Fully-qualified production device.
Support tool development evolutionary flow:
PRODUCT PREVIEW
TMDX
Development-support product that has not yet completed Texas Instruments internal
qualification testing.
TMDS
Fully qualified development-support product.
TMX and TMP devices and TMDX development-support tools are shipped against the following
disclaimer:
"Developmental product is intended for internal evaluation purposes."
TMS devices and TMDS development-support tools have been characterized fully, and the quality and
reliability of the device have been demonstrated fully. TI's standard warranty applies.
Predictions show that prototype devices (TMX or TMP) have a greater failure rate than the standard
production devices. Texas Instruments recommends that these devices not be used in any production
system because their expected end-use failure rate still is undefined. Only qualified production devices are
to be used.
TI device nomenclature also includes a suffix with the device family name. This suffix indicates the
package type (for example, ZCH), and the temperature range (for example, "Blank" is the commercial
temperature range).
Figure 2-3 provides a legend for reading the complete device name for any DSP platform member.
42
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
TMS 320
C
5515
A
ZCH
A
12
PREFIX
TMX = Experimental device
TMS = Qualified device
DEVICE MAXIMUM OPERATING FREQUENCY
10 = 60 MHz at 1.05 V, 100 MHZ at 1.3 V
12 = 75 MHz at 1.05 V, 120 MHZ at 1.3 V
DEVICE FAMILY
320 = TMS320™ DSP family
TEMPERATURE RANGE
Blank = 0 ° C to 70° C, Commercial Temperature
A = –40° C to 85° C, Industrial Temperature
TECHNOLOGY
C = Dual-supply CMOS
PACKAGE TYPE
ZCH = 196-pin plastic BGA, with Pb-Free
soldered balls [Green]
DEVICE
C55x™ DSP: 5515
5514
SILICON REVISION
Revision 2.0
PRODUCT PREVIEW
Figure 2-3. TMS320C5515 Device Nomenclature
Device Overview
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
43
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
3 Device Configuration
3.1
System Registers
The system registers are used to configure the device and monitor its status. Brief descriptions of the
various system registers are shown in Table 3-1.
Table 3-1. Idle Control, Status, and System Registers
PRODUCT PREVIEW
44
CPU WORD
ADDRESS
ACRONYM
0001h
ICR
Idle Control Register
Idle Status Register
COMMENTS
Register Description
0002h
ISTR
1C00h
EBSR
1C02h
PCGCR1
Peripheral Clock Gating Control Register 1
1C03h
PCGCR2
Peripheral Clock Gating Control Register 2
1C04h
PSRCR
Peripheral Software Reset Counter Register
1C05h
PRCR
Peripheral Reset Control Register
1C14h
TIAFR
Timer Interrupt Aggregation Flag Register
1C16h
ODSCR
1C17h
PDINHIBR1
Pull-Down Inhibit Register 1
1C18h
PDINHIBR2
Pull-Down Inhibit Register 2
1C19h
PDINHIBR3
Pull-Down Inhibit Register 3
1C1Ah
DMA0CESR1
DMA0 Channel Event Source Register 1
see Section 3.6.1 of this
document.
External Bus Selection Register
Output Drive Strength Control Register
1C1Bh
DMA0CESR2
DMA0 Channel Event Source Register 2
1C1Ch
DMA1CESR1
DMA1 Channel Event Source Register 1
1C1Dh
DMA1CESR2
DMA1 Channel Event Source Register 2
1C26h
ECDR
EMIF Clock Divider Register
1C28h
RAMSLPMDCNTLR1
RAM Sleep Mode Control Register 1
1C2Eh
RAMSLPMDCNTLR2
RAM Sleep Mode Control Register 2
1C30h
DMAIFR
DMA Interrupt Flag Register
1C31h
DMAIER
DMA Interrupt Enable Register
1C32h
USBSCR
USB System Control Register
1C33h
ESCR
EMIF System Control Register
1C36h
DMA2CESR1
DMA2 Channel Event Source Register 1
1C37h
DMA2CESR2
DMA2 Channel Event Source Register 2
1C38h
DMA3CESR1
DMA3 Channel Event Source Register 1
1C39h
DMA3CESR2
DMA3 Channel Event Source Register 2
1C3Ah
CLKSTOP
7004h
LDOCNTL
Peripheral Clock Stop Request/Acknowledge Register
LDO Control Register
Device Configuration
see Section 3.2.1.3 of this
document.
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
3.2
SPRS645 – JANUARY 2010
Power Considerations
The C5515 provides several means of managing power consumption.
To
•
•
•
•
•
•
•
•
•
LDO Configuration
The C5515 includes three Low-Dropout Regulators (LDOs) which can be used to regulate the power
supplies of the analog PLL and SAR ADC/Power Management (ANA_LDO), Digital Core (DSP_LDO), and
USB Core (USB_LDO).
These LDOs are controlled by a combination of pin configuration and register settings. For more detailed
information see the following sections.
3.2.1.1
LDO Input
The LDOI pins (B12, F13, F14) provide the power to the internal Analog LDO, DSP LDO, USB LDO, the
bandgap reference generator, and some I/O input pins, and can range from 1.8 V to 3.6 V. The Bandgap
provides accurate voltage and current references to the POR, LDOs, PLL, and SAR; therefore, for proper
device operation, power must always be applied to the LDOI pins even if the LDO outputs are not used.
3.2.1.2
LDO Outputs
The ANA_LDOO pin (A12) is the output of the internal ANA_LDO and can provide regulated 1.3 V power
of up to TBD mA. The ANA_LDOO is intended to be connected, on the board, to the VDDA_ANA and
VDDA_PLL pins to provide power to the 10-bit SAR ADC, Power Management Circuits, and System PLL.
VDDA_ANA and VDDA_PLL may be powered by this LDO output, which is recommended, to take advantage of
device's power management techniques, or by an external power supply. The ANA_LDO cannot be
disabled individually (see Section 3.2.1.3, LDO Control).
The DSP_LDOO pin (E10) is the output of the internal DSP_LDO and provides software-selectable
regulated 1.3 V or regulated 1.05 V power of up to TBD mA. The DSP_LDOO is intended to be
connected, on the board, to the CVDD pins. In this configuration, the DSP_LDO_EN pin should be tied to
the board VSS, thus enabling the DSP_LDO. Optionally, the CVDD pins may be powered by an external
power supply; in this configuration the DSP_LDO_EN pin should be tied (high) to LDOI, disabling
DSP_LDO. The DSP_LDO_EN also affects how reset is generated to the chip (for more details, see the
DSP_LDO_EN pin description in Table 2-19, Regulators and Power Management Terminal Functions).
When the DSP_LDO is disabled, its output pin is in a high-impedance state. Note: DSP_LDO_EN is not
intended to be changed dynamically.
The USB_LDOO pin (F12) is the output of the internal USB_LDO and provides regulated 1.3 V,
software-switchable (on/off) power of up to TBD mA. The USB_LDOO is intended to be connected, on the
board, to the USB_VDD1P3 and USB_VDDA1P3 pins to provide power to portions of the USB. Optionally, the
USB_VDD1P3 and USB_VDDA1P3 may be powered by an external power supply and the USB_LDO can be
left disabled. When the USB_LDO is disabled, its output pin is in a high-impedance state.
Device Configuration
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
45
PRODUCT PREVIEW
3.2.1
minimize power consumption, the C5515 divides its circuits into nine main isolated supply domains:
LDOI (LDOs and Bandgap Power Supply)
Analog POR, SAR, and PLL (VDDA_ANA and VDDA_PLL)
RTC Core (CVDD_RTC)
Digital Core (CVDD)
USB Core (USB_ VDD1P3 and USB_VDDA1P3)
USB PHY and USB PLL (USB_VDDOSC, USB_VDDA3P3, and USB_VDDPLL)
EMIF I/O (DVDDEMIF)
RTC I/O (DVDDRTC)
Rest of the I/O (DVDDIO)
TMS320C5515
SPRS645 – JANUARY 2010
3.2.1.3
www.ti.com
LDO Control
All three LDOs can be simultaneously disabled via software by writing to either the BG_PD bit or the
LDO_PD bit in the RTCPMGT register (seeFigure 3-1). When the LDOs are disabled via this mechanism,
the only way to re-enable them is by asserting the WAKEUP signal pin (which must also have been
previously enabled to allow wakeup), or by a previously enabled and configured RTC alarm, or by cycling
power to the CVDDRTC pin.
ANA_LDO: The ANA_LDO is only disabled by the BG_PD and the LDO_PD mechanism described above.
Otherwise, it is always enabled.
DSP_LDO: The DSP_LDO can be statically disabled by the DSP_LDO_EN pin as described
Section 3.2.1.2, LDO Outputs above. It can be also dynamically disabled via the BG_PD and the LDO_PD
mechanism described above. The DSP_LDO can change its output voltage dynamically by software via
the DSP_LDO_V bit in the LDOCNTL register (see Figure 3-2). The DSP_LDO output voltage is set to 1.3
V at reset.
USB_LDO: The USB_LDO can be independently and dynamically enabled or disabled by software via the
USB_LDO_EN bit in the LDOCNTL register (see Figure 3-2). The USB _LDO is disabled at reset.
Table 3-4 shows the ON/OFF control of each LDO and its register control bit configurations.
PRODUCT PREVIEW
46
Device Configuration
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
15
8
Reserved
R-0
7
4
3
2
1
0
Reserved
5
WU_DOUT
WU_DIR
BG_PD
LDO_PD
RTCCLKOUTE
N
R-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Figure 3-1. RTC Power Management Register (RTCPMGT) [1930h]
Table 3-2. RTCPMGT Register Bit Descriptions
NAME
RESERVED
Reserved. Read-only, writes have no effect.
4
WU_DOUT
Wakeup output, active low/open-drain.
0 = WAKEUP pin driven low.
1 = WAKEUP pin is in high-impedance (Hi-Z).
3
2
WU_DIR
BG_PD
DESCRIPTION
Wakeup pin direction control.
0 = WAKEUP pin configured as a input.
1 = WAKEUP pin configured as a output.
Note: When the WAKEUP pin is configured as an input, it is active high. When the WAKEUP pin is
conifgured as an output, is an open-drain that is active low and should be externally pulled-up via a
10-kΩ resistor to DVDDRTC. WU_DIR must be configured as an input to allow the WAKEUP pin to
wake the device up from idle modes.
Bandgap, on-chip LDOs, and the analog POR power down bit.
This bit shuts down the on-chip LDOs (ANA_LDO, DSP_LDO, and USB_LDO), the Analog POR,
and Bandgap reference. BG_PD and LDO_PD are only intended to be used when the internal
LDOs supply power to the chip. If the internal LDOs are bypassed and not used then the BG_PD
and LDO_PD power down mechanisms should not be used since POR gets powered down and the
POWERGOOD signal is not generated properly.
After this bit is asserted, the on-chip LDOs, Analog POR, and the Bandgap reference can be
re-enabled by the WAKEUP pin (high) or the RTC alarm interrupt. The Bandgap circuit will take
about 100 msec to charge the external 0.1 uF capacitor via the internal 326-kΩ resistor.
0 = On-chip LDOs, Analog POR, and Bandgap reference are enabled.
1 = On-chip LDOs, Analog POR, and Bandgap reference are disabled (shutdown).
1
LDO_PD
On-chip LDOs and Analog POR power down bit.
This bit shuts down the on-chip LDOs (ANA_LDO, DSP_LDO, and USB_LDO) and the Analog
POR. BG_PD and LDO_PD are only intended to be used when the internal LDOs supply power to
the chip. If the internal LDOs are bypassed and not used then the BG_PD and LDO_PD power
down mechanisms should not be used since POR gets powered down and the POWERGOOD
signal is not generated properly.
After this bit is asserted, the on-chip LDOs and Analog POR can be re-enabled by the WAKEUP
pin (high) or the RTC alarm interrupt. This bit keeps the Bandgap reference turned on to allow a
faster wake-up time with the expense power consumption of the Bandgap reference.
0 = On-chip LDOs and Analog POR are enabled.
1 = On-chip LDOs and Analog POR are disabled (shutdown).
0
RTCCLKOUTEN
Clockout output enable bit.
0 = Clock output disabled.
1 = Clock output enabled.
Device Configuration
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
47
PRODUCT PREVIEW
BIT
15:5
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
15
8
Reserved
R-0
7
1
0
Reserved
2
DSP_LDO_V
USB_LDO_EN
R-0
R/W-0
R/W-0
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Figure 3-2. LDO Control Register (LDOCNTL) [7004h]
Table 3-3. LDOCNTL Register Bit Descriptions
BIT
NAME
15:2
RESERVED
Reserved. Read-only, writes have no effect.
DESCRIPTION
1
DSP_LDO_V
DSP_LDO voltage select bit.
0 = DSP_LDOO is regulated to 1.3 V.
1 = DSP_LDOO is regulated to 1.05 V.
0
USB_LDO_EN
USB_LDO enable bit.
0 = USB_LDO output is disabled. USB_LDOO pin is placed in high-impedance (Hi-Z) state.
1 = USB_LDO output is enabled. USB_LDOO is regulated to 1.3 V.
PRODUCT PREVIEW
Table 3-4. LDO Controls Matrix
RTCPMGT Register
(0x1930)
48
LDOCNTL Register
(0x7004)
BG_PD Bit
LDO_PD Bit
USB_LDO_EN Bit
DSP_LDO_EN
(Pin D12)
ANA_LDO
DSP_LDO
USB_LDO
1
Don't Care
Don't Care
Don't Care
OFF
OFF
OFF
Don't Care
1
Don't Care
Don't Care
OFF
OFF
OFF
0
0
0
Low
ON
ON
OFF
0
0
0
High
ON
OFF
OFF
0
0
1
Low
ON
ON
ON
Device Configuration
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
3.3
SPRS645 – JANUARY 2010
Clock Considerations
The system clock, which is used by the CPU and most of the DSP peripherals, is controlled by the system
clock generator. The system clock generator features a software-programmable PLL multiplier and several
dividers. The clock generator accepts an input reference clock from the CLKIN pin or the output clock of
the 32.768-KHz real-time clock (RTC) oscillator. The selection of the input reference clock is based on the
state of the CLK_SEL pin. The CLK_SEL pins is required to be statically tied high or low and cannot
change dynamically after reset.
In addition, the DSP requires a reference clock for USB applications. The USB reference clock is
generated using a dedicated on-chip oscillator with a 12-MHz external crystal connected to the USB_MXI
and USB_MXO pins.
The RTC oscillator generates a clock when a 32.768-KHz crystal is connected to the RTC_XI and
RTC_XO pins. The 32.768-KHz crystal can be disabled if CLKIN is used as the clock source for the DSP.
However, when the RTC oscillator is disabled, the RTC peripheral will not operate and the RTC registers
(I/O address range 1900h – 197Fh) will not be accessible. This includes the RTC power management
register (RTCPMGT) which controls the RTCLKOUT and WAKEUP pins. To disable the RTC oscillator,
connect the RTC_XI pin to CVDDRTC and the RTC_XO pin to ground.
For more information on crystal specifications for the RTC oscillator and the USB oscillator, see
Section 5.4, External Clock Input From RTC_XI, CLKIN, and USB_MXI Pins.
3.3.1
Clock Configurations After Device Reset
After reset, the on-chip Bootloader programs the system clock generator based on the input clock selected
via the CLK_SEL pin. If CLK_SEL = 0, the Bootloader programs the system clock generator and sets the
system clock to 12.288 MHz (multiply the 32.768-kHz RTC oscillator clock by 375). If CLK_SEL = 1, the
Bootloader bypasses the system clock generator altogether and the system clock is driven by the CLKIN
pin. In this case, the CLKIN frequency is expected to be 11.2896 MHz, 12.0 MHz, or 12.288 MHz. While
the bootloader tries to boot from the USB (currently not supported), the clock generator will be
programmed to output approximately 36 MHz.
3.3.1.1
Device Clock Frequency
After the boot process is complete, the user is allowed to re-program the system clock generator to bring
the device up to the desired clock frequency and the desired peripheral clock state (clock gating or not).
The user must adhere to various clock requirements when programming the system clock generator. For
more information, see Section 5.5, Clock PLLs.
Note: The on-chip Bootloader allows for DSP registers to be configured during the boot process.
However, this feature must not be used to change the output frequency of the system clock generator
during the boot process. Timer0 is also used by the bootloader to allow for 200 ms of BG_CAP settling
time. The bootloader register modification feature must not modify the Timer0 registers.
3.3.1.2
Peripheral Clock State
The clock and reset state of each of peripheral is controlled through a set of system registers. The
peripheral clock gating control registers (PCGCR1 and PCGCR2) are used to enable and disable
peripheral clocks. The peripheral software reset counter register (PSRCR) and the peripheral reset control
register (PRCR) are used to assert and de-assert peripheral reset signals.
At hardware reset, all of the peripheral clocks are off to conserve power. After hardware reset, the DSP
boots via the bootloader code in ROM. During the boot process, the bootloader queries each peripheral to
Device Configuration
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
49
PRODUCT PREVIEW
The USB reference clock is not required if the USB peripheral is not being used. To completely disable the
USB oscillator, connect the USB_MXI pin to ground (VSS) and leave the USB_MXO pin unconnected. The
USB oscillator power pins (USB_VDDOSC and USB_VSSOSC) should also be connected to ground.
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
determine if it can boot from that peripheral. In other words, it reads each peripheral looking for a valid
boot image file. At that time, the individual peripheral clocks will be enabled for the query and then
disabled again when the bootloader is finished with the peripheral. By the time the bootloader releases
control to the user code, all peripheral clocks will be off and all domains in the ICR, except the CPU
domain, will be idled.
3.3.1.3
USB Oscillator Control
The USB oscillator is controlled through the USB system control register (USBSCR). To enable the
oscillator, the USBOSCDIS and USBOSCBIASDIS bits must be cleared to 0. The user must wait until the
USB oscillator stabilizes before proceeding with the USB configuration. The USB oscillator stabilization
time is typically 100 ms, with a 10 ms maximum (Note: the startup time is highly dependent on the ESR
and capacitive load on the crystal).
PRODUCT PREVIEW
50
Device Configuration
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
3.4
SPRS645 – JANUARY 2010
Boot Sequence
The boot sequence is a process by which the device's on-chip memory is loaded with program and data
sections from an external image file (in flash memory, for example). The boot sequence also allows,
optionally, for some of the device's internal registers to be programmed with predetermined values. The
boot sequence is started automatically after each device reset. For more details on device reset, see
Section 5.7, Reset.
The C5515 Bootloader follows the following steps as shown in Figure 3-3
1. Immediately after reset, the CPU fetches the reset vector from 0xFFFF00. MP/MC is 0 by default, so
0xFFFF00 is mapped to internal ROM. The PLL is in bypass mode.
2. Set CLKOUT slew rate control to slow slew rate.
3. Idle all peripherals, MPORT and HWA.
4. If CLK_SEL = 0, the Bootloader powers up the PLL and sets its output frequency to 12.288 MHz (with
a 375x multiplier using VP = 749, VS = 0, input divider disabled, output divide-by-8 enabled, and output
divider enabled with VO = 0). If CLK_SEL = 1, the Bootloader keeps the PLL bypassed.
5. Apply manufacturing trim to the bandgap references.
6. Disable CLKOUT.
7. Test for NOR boot on all asynchronous CS spaces (EM_CS[2:5]) with 16-bit access:
(a) Check the first 2 bytes read from boot signature.
(b) If the boot signature is not valid, go to step 8.
(c) Set Register Configuration, if present in boot image.
(d) Attempt NOR boot, go to step 15.
8. Test for NAND boot on all asynchronous CS spaces (EM_CS[2:5]) with 8-bit access:
(a) Check the first 2 bytes read from boot table for a boot signature match.
(b) If the boot signature is not valid, go to step 9.
(c) Set Register Configuration, if present in boot image.
(d) Attempt NAND boot, go to step 15.
9. Test for 16-bit and 24-bit SPI EEPROM boot on SPI_CS[0] with 500-KHz clock rate and for Parallel
Port Mode on External bus Selection Register set to 5, then set to 6:
(a) Check the first 2 bytes read from boot table for a boot signature match using 16-bit address mode.
(b) If the boot signature is not valid, read the first 2 bytes again using 24-bit address mode.
(c) If the boot signature is not valid from either case (16-bit and 24-bit address modes), go to step 10.
(d) Set Register Configuration, if present in boot image.
(e) Attempt SPI Serial Memory boot, go to step 15.
10. Test for I2C EEPROM boot with a 7-bit slave address 0x50 and 400-kHz clock rate.
(a) Check the first 2 bytes read from boot table for a boot signature match.
(b) If the boot signature is not valid, go to step 11.
(c) Set Register Configuration, if present in boot image.
(d) Attempt I2C EEPROM boot, go to step 15.
11. Test for MMC/SD boot --- For more information on MMC/SD boot, contact your local sales
representative.
12. Set the PLL output to approximately 36 MHz. If CLK_SEL = 1, CLKIN multiplied by 3x, ; if CLK_SEL =
0, CLKIN is multiplied by 1125x.
13. Test for USB boot --- For more information on USB boot, contact your local sales representative.
Device Configuration
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
51
PRODUCT PREVIEW
There are several methods by which the memory and register initialization can take place. Each of these
methods is referred to as a boot mode. At reset, the device cycles through different boot modes until an
image is found with a valid boot signature. The on-chip Bootloader allows the DSP registers to be
configured during the boot process, if the optional register configuration section is present in the boot
image (see Figure 3-3 ). For more information on the boot modes supported, see Section 3.4.1, Boot
Modes.
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
14. If the boot signature is not valid, then go back to step 14 and repeat.
15. Enable TIMER0 to start counting 200 ms.
16. Ensure a minimum of 200 ms has elapsed since step 15 before proceeding to execute the bootloaded
code.
17. Jump to the entry point specified in the boot image.
CLK SEL = 1
?
No
Setup PLL to
x375
Yes
Internal Configuration
NOR Boot
?
Yes
No
PRODUCT PREVIEW
NAND Boot
?
Yes
No
SPI Boot
?
Yes
No
Set Register
Configuration
I2C Boot
?
No
MMC/SD0 Boot
(Not Supported)
?
Yes
Copy Boot
Image Sections
to System
Memory
Start Timer0 to Count
200 ms
USB Boot
(Not Supported)
?
Has Timer0
Counter Expired
?
No
Yes
Jump to Stored
Execution Point
Figure 3-3. Bootloader Software Architecture
3.4.1
Boot Modes
The C5515 DSP supports the following boot modes in the following device order: NOR Flash, NAND
Flash, SPI 16-bit EEPROM, SPI 24-bit Flash, I2C EEPROM, and MMC/SD card. The boot mode is
determined by checking for a valid boot signature on each supported boot device. The first boot device
with a valid boot signature will be used to load and execute the user code. If none of the supported boot
devices have a valid boot signature, the Bootloader goes into an endless loop checking the USB boot
mode and the device must be reset to look for another valid boot image in the supported boot modes.
Note: For detailed information on MMC/SD and USB boot modes, contact your local sales representative.
52
Device Configuration
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
3.4.2
SPRS645 – JANUARY 2010
Boot Configuration
After reset, the on-chip Bootloader programs the system clock generator based on the input clock selected
via the CLK_SEL pin. If CLK_SEL = 0, the Bootloader programs the system clock generator and sets the
system clock to 12.288 MHz (multiply the 32.768-KHz RTC oscillator clock by 375). If CLK_SEL = 1, the
Bootloader bypasses the system clock generator altogether and the system clock is driven by the CLKIN
pin.
Note:
• When CLK_SEL =1, the CLKIN frequency is expected to be 11.2896 MHz, 12.0 MHz, or 12.288 MHz.
• The on-chip Bootloader allows for DSP registers to be configured during the boot process. However,
this feature must not be used to change the output frequency of the system clock generator during the
boot process. Timer0 is also used by the bootloader to allow for 200 ms of BG_CAP settling time. The
bootloader register modification feature must not modify the Timer0 registers.
3.4.3
DSP Resources Used By the Bootloader
The Bootloader uses SARAM block 31 for the storing of temporary data. This block of memory is reserved
during the boot process. However, after the boot process is complete, it can be used by the user
application.
Device Configuration
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
53
PRODUCT PREVIEW
After hardware reset, the DSP boots via the bootloader code in ROM. During the boot process, the
bootloader queries each peripheral to determine if it can boot from that peripheral. At that time, the
individual peripheral clocks will be enabled for the query and then disabled when the bootloader is finished
with the peripheral. By the time the bootloader releases control to the user code, all peripheral clocks will
be "off" and all domains in the ICR, except the CPU domain, will be idled.
TMS320C5515
SPRS645 – JANUARY 2010
3.5
www.ti.com
Configurations at Reset
Some device configurations are determined at reset. The following subsections give more details.
3.5.1
Device and Peripheral Configurations at Device Reset
Table 3-5 summarizes the device boot and configuration pins that are required to be statically tied high,
tied low, or left unconnected during device operation. For proper device operation, a device reset should
be initiated after changing any of these pin functions.
Table 3-5. Default Functions Affected by Device Configuration Pins
SIGNAL NO.
IPU/IPD
FUNCTIONAL DESCRIPTION
DSP_LDO_EN
D12
–
DSP_LDO enable input.
This signal is not intended to be dynamically
switched.
0 = DSP_LDO is enabled. The internal DSP LDO
is enabled to regulate power on the DSP_LDOO
pin at either 1.3 V or 1.05 V according to the
LDO_DSP_V bit in the LDOCNTL register, see
Figure 3-2). At power-on-reset, the internal POR
monitors the DSP_LDOO pin voltage and
generates the internal POWERGOOD signal
when the DSP_LDO voltage is above a minimum
threshold voltage. The internal device reset is
generated by the AND of POWERGOOD and the
RESET pin.
1 = DSP_LDO is disabled and the DSP_LDOO
pin is in high-impedance (Hi-Z). The internal
voltage monitoring on the DSP_LDOO is
bypassed and the internal POWERGOOD signal
is immediately set high. The RESET pin (D6) will
act as the sole reset source for the device. If an
external power supply is used to provide power to
CVDD, then DSP_LDO_EN should be tied to
LDOI, DSP_LDOO should be left unconnected,
and the RESET pin must be asserted
appropriately for device initialization after
powerup.
PRODUCT PREVIEW
CONFIGURATION PINS
Note: to pullup this pin, connect it to the same
supply as LDOI pins.
CLK_SEL
C7
–
Clock input select.
0 = 32-KHz on-chip oscillator drives the RTC
timer and the DSP clock generator. CLKIN is
ignored.
1 = CLKIN drives the DSP clock generator and
the 32-KHz on-chip oscillator drives only the RTC
timer.
This pin is not allowed to change during device
operation; it must be tied to DVDDIO or GND at
the board.
For proper device operation, external pullup/pulldown resistors may be required on these device
configuration pins. For discussion on situations where external pullup/pulldown resistors are required, see
Section 3.8.1, Pullup/Pulldown Resistors.
This device also has RESERVED pins that need to be configured correctly for proper device operation
(statically tied high, tied low, or left unconnected at all times). For more details on these pins, see
Table 2-20, Reserved and No Connects Terminal Functions.
54
Device Configuration
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
3.6
SPRS645 – JANUARY 2010
Configurations After Reset
The following sections provide details on configuring the device after reset. Multiplexed pin functions are
selected by software after reset. For more details on multiplexed pin function control, see Section 3.7,
Multiplexed Pin Configurations.
3.6.1
External Bus Selection Register (EBSR)
The External Bus Selection Register (EBSR) determines the mapping of the LCD controller, I2S2, I2S3,
UART, SPI, and GPIO signals to 21 signals of the external parallel port pins. It also determines the
mapping of the I2S or MMC/SD ports to serial port 1 pins and serial port 2 pins. The EBSR register is
located at port address 0x1C00. Once the bit fields of this register are changed, the routing of the signals
takes place on the next CPU clock cycle.
Before modifying the values of the external bus selection register, you must clock gate all affected
peripherals through the Peripheral Clock Gating Control Register . After the external bus selection register
has been modified, you must reset the peripherals before using them through the Peripheral Software
Reset Counter Register.
After the boot process is complete, the external bus selection register must be modified only once, during
device configuration. Continuously switching the EBSR configuration is not supported.
15
14
12
11
10
9
8
Reserved
PPMODE
SP1MODE
SP0MODE
R-0
R/W-000
R/W-00
R/W-00
7
6
5
4
3
2
1
0
Reserved
Reserved
A20_MODE
A19_MODE
A18_MODE
A17_MODE
A16_MODE
A15_MODE
R-0
R-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Figure 3-4. External Bus Selection Register (EBSR) [1C00h]
Device Configuration
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
55
PRODUCT PREVIEW
Additionally, the EBSR controls the function of the upper bits of the EMIF address bus. Pins EM_A[20:15]
can be individually configured as GPIO pins through the Axx_MODE bits. When Axx_MODE = 1, the
EM_A[xx] pin functions as a GPIO pin. When Axx_MODE = 0, the EM_A[xx] pin retains its EMIF
functionality.
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
Table 3-6. EBSR Register Bit Descriptions
BIT
NAME
15
RESERVED
Reserved. Read-only, writes have no effect.
PPMODE
Parallel Port Mode Control Bits. These bits control the pin multiplexing of the LCD Controller, SPI,
UART, I2S2, I2S3, and GP[31:27, 20:18] pins on the parallel port. For more details, see Table 3-7,
LCD Controller, SPI, UART, I2S2, I2S3, and GP[31:27, 20:18] Pin Multiplexing.
000 = Mode 0 (16-bit LCD Controller). All 21 signals of the LCD Bridge module are routed to the 21
external signals of the parallel port.
001 = Mode 1 (SPI, GPIO, UART, and I2S2). 7 signals of the SPI module, 6 GPIO signals, 4
signals of the UART module and 4 signals of the I2S2 module are routed to the 21 external signals
of the parallel port.
010 = Mode 2 (8-bit LCD Controller and GPIO). 8-bits of pixel data of the LCD Controller module
and 8 GPIO are routed to the 21 external signals of the parallel port.
011 = Mode 3 (8-bit LCD Controller, SPI, and I2S3). 8-bits of pixel data of the LCD Controller
module, 4 signals of the SPI module, and 4 signals of the I2S3 module are routed to the 21 external
signals of the parallel port.
100 = Mode 4 (8-bit LCD Controller, I2S2, and UART). 8-bits of pixel data of the LCD Controller
module, 4 siignals of the I2S2 module, and 4 signals of the UART module are routed to the 21
external signals of the parallel port.
101 = Mode 5 (8-bit LCD Controller, SPI, and UART). 8-bits of pixel data of the LCD Controller
module, 4 signals of the SPI module, and 4 signals of the UART module are routed to the 21
external signals of the parallel port.
110 = Mode 6 (SPI, I2S2, I2S3, and GPIO). 7 signals of the SPI module, 4 signals of the I2S2
module, 4 signals of the I2S3 module, and 6 GPIO are routed to the 21 external signals of the
parallel port.
111 = Reserved.
SP1MODE
Serial Port 1 Mode Control Bits. The bits control the pin multiplexing of the MMC1, I2S1, and GPIO
pins on serial port 1. For more details, see Table 3-8, MMC1, I2S1 , and GP[11:6] Pin Multiplexing.
00 = Mode 0 (MMC/SD1 ). All 6 signals of the MMC/SD1 module are routed to the 6 external
signals of the serial port 1 .
01 = Mode 1 (I2S1 and GP[11:10]). 4 signals of the I2S1 module and 2 GP[11:10] signals are
routed to the 6 external signals of the serial port 1.
10 = Mode 2 (GP[11:6]). 6 GPIO signals (GP[11:6]) are routed to the 6 external signals of the serial
port 1.
11 = Reserved.
9:8
SP0MODE
Serial Port 0 Mode Control Bits. The bits control the pin multiplexing of the MMC0, I2S0, and GPIO
pins on serial port 0. For more details, see Section 3.7.1.3, MMC0, I2S0, and GP[5:0] Pin
Multiplexing.
00 = Mode 0 (MMC/SD0). All 6 signals of the MMC/SD0 module are routed to the 6 external signals
of the serial port 0.
01 = Mode 1 (I2S0 and GP[5:0]). 4 signals of the I2S0 module and 2 GP[5:4] signals are routed to
the 6 external signals of the serial port 0.
10 = Mode 2 (GP[5:0]). 6 GPIO signals (GP[5:0]) are routed to the 6 external signals of the serial
port 0.
11 = Reserved.
7
RESERVED
Reserved. Read-only, writes have no effect.
6
RESERVED
Reserved. Read-only, writes have no effect.
5
A20_MODE
A20 Pin Mode Bit. This bit controls the pin mulitplexing of the EMIF address 20 (EM_A[20]) and
general-purpose input/output pin 26 (GP[26]) pin functions.
0 = Pin function is EMIF address pin 20 (EM_A[20]).
1 = Pin function is general-purpose input/output pin 26 (GP[26]).
4
A19_MODE
A19 Pin Mode Bit. This bit controls the pin mulitplexing of the EMIF address 19 (EM_A[19]) and
general-purpose input/output pin 25 (GP[25]) pin functions.
0 = Pin function is EMIF address pin 19 (EM_A[19]).
1 = Pin function is general-purpose input/output pin 25 (GP[25]).
A18_MODE
A18 Pin Mode Bit. This bit controls the pin mulitplexing of the EMIF address 18 (EM_A[18]) and
general-purpose input/output pin 24 (GP[24]) pin functions.
0 = Pin function is EMIF address pin 18 (EM_A[18]).
1 = Pin function is general-purpose input/output pin 24 (GP[24]).
A17_MODE
A17 Pin Mode Bit. This bit controls the pin mulitplexing of the EMIF address 17 (EM_A[17]) and
general-purpose input/output pin 23 (GP[23]) pin functions. For more details, see Table 3-9,
EM_A[20:16] and GP[26:21] Pin Multiplexing.
0 = Pin function is EMIF address pin 17 (EM_A[17]).
1 = Pin function is general-purpose input/output pin 23 (GP[23]).
14:12
PRODUCT PREVIEW
11:10
3
2
56
DESCRIPTION
Device Configuration
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Table 3-6. EBSR Register Bit Descriptions (continued)
BIT
1
0
3.6.2
NAME
DESCRIPTION
A16_MODE
A16 Pin Mode Bit. This bit controls the pin mulitplexing of the EMIF address 16 (EM_A[16]) and
general-purpose input/output pin 22 (GP[22]) pin functions. For more details, see Table 3-9,
EM_A[20:16] and GP[26:21] Pin Multiplexing.
0 = Pin function is EMIF address pin 16 (EM_A[16]).
1 = Pin function is general-purpose input/output pin 22 (GP[22]).
A15_MODE
A15 Pin Mode Bit. This bit controls the pin mulitplexing of the EMIF address 15 (EM_A[15]) and
general-purpose input/output pin 21 (GP[21]) pin functions. For more details, see Table 3-9,
EM_A[20:16] and GP[26:21] Pin Multiplexing.
0 = Pin function is EMIF address pin 15 (EM_A[15]).
1 = Pin function is general-purpose input/output pin 21 (GP[21]).
LDO Control Register [7004h]
When the DSP_LDO is enabled by the DSP_LDO_EN pin [D12], by default, the DSP_LDOO voltage is set
to 1.3 V. The DSP_LDOO voltage can be programmed to be either 1.05 V or 1.3 V via the DSP_LDO_V
bit (bit 1) in the LDO Control Register (LDOCNTL).
For more detailed information on the LDOs, see Section 3.2.1 LDO Configuration.
3.6.3
EMIF and USB System Control Registers (ESCR and USBSCR) [1C33h and 1C32h]
After reset, by default, the CPU performs 16-bit accesses to the EMIF and USB registers and data space.
To perform 8-bit accesses to the EMIF data space, the user must set the BYTEMODE bits to 01b for the
"high byte" or 10b for the "low byte" in the EMIF System Control Register (ESCR). Similarly, the
BYTEMODE bits in the USB System Control Register (USBSCR) must also be configured for byte access.
3.6.4
Peripheral Clock Gating Control Registers (PCGCR1 and PCGCR2) [1C02h and 1C03h]
After hardware reset, the DSP executes the on-chip bootloader from ROM. As the bootloader executes, it
selectively enables the clock of the peripheral being queried for a valid boot. If a valid boot source is not
found, the bootloader disables the clock to that peripheral and moves on to the next peripheral in the boot
order. After the boot process is complete, all of the peripheral clocks will be off and all domains in the ICR,
except for the CPU domain, will be idled (this includes the MPORT and HWA). The user must enable the
clocks to the peripherals and CPU ports that are going to be used. The peripheral clock gating control
registers (PCGCR1 and PCGCR2) are used to enable and disable the peripheral clocks.
3.6.5
Pullup/Pulldown Inhibit Registers (PDINHIBR1/2/3) [1C17h, 1C18h, and 1C19h,
respectively]
Each internal pullup and pulldown (IPU/IPD) resistor on the C5515 DSP, except for the IPD on TRST, can
be individually controlled through the IPU/IPD registers (PDINHIBR1 [1C17h] , PDINHIBR2 [1C18h], and
PDINHIBR3 [1C19h]). To minimize power consumption, internal pullup or pulldown resistors should be
disabled in the presence of an external pullup or pulldown resistor or external driver. Section 3.8.1,
Pullup/Pulldown Resistors, describes other situations in which an pullup and pulldown resistors are
required.
When CVDD is powered down, pullup and pulldown resistors will be forced disabled and an internal
bus-holder will be enabled. For more detailed information, see Section 5.3.2, Digital I/O Behavior When
Core Power (CVDD) is Down.
Device Configuration
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
57
PRODUCT PREVIEW
At reset, the USB_LDO is turned off. The USB_LDO can be enabled via the USBLDOEN bit (bit 0) in the
LDOCNTL register.
TMS320C5515
SPRS645 – JANUARY 2010
3.6.6
www.ti.com
Output Slew Rate Control Register (OSRCR) [1C16h]
To provide the lowest power consumption setting, the DSP has configurable slew rate control on the EMIF
and CLKOUT output pins. The output slew rate control register (OSRCR) is used to set a subset of the
device I/O pins, namely CLKOUT and EMIF pins, to either fast or slow slew rate. The slew rate feature is
implemented by staging/delaying turn-on times of the parallel p-channel drive transistors and parallel
n-channel drive transistors of the output buffer. In the slow slew rate configuration, the delay is longer, but
ultimately the same number of parallel transistors are used to drive the output high or low. Thus, the drive
strength is ultimately the same. The slower slew rate control can be used for power savings and has the
greatest effect at lower DVDDIO voltages.
PRODUCT PREVIEW
58
Device Configuration
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
3.7
SPRS645 – JANUARY 2010
Multiplexed Pin Configurations
The C5515 DSP uses pin multiplexing to accommodate a larger number of peripheral functions in the
smallest possible package, providing the ultimate flexibility for end applications. The external bus selection
register (EBSR) controls all the pin multiplexing functions on the device.
3.7.1
Pin Multiplexing Details
This section discusses how to program the external bus selection register (EBSR) to select the desired
peripheral functions and pin muxing. See the individual pin mux sections for pin muxing details for a
specific muxed pin. After changing any of the pin mux control registers, it will be necessary to reset the
peripherals that are affected.
3.7.1.1
LCD Controller, SPI, UART, I2S2, I2S3, and GP[31:27, 20:18] Pin Multiplexing [EBSR.PPMODE
Bits]
PRODUCT PREVIEW
The LCD Controller, SPI, UART, I2S2, I2S3, and GPIO signal muxing is determined by the value of the
PPMODE bit fields in the External Bus Selection Register (EBSR) register. For more details on the actual
pin functions, see Table 3-7 .
Device Configuration
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
59
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
Table 3-7. LCD Controller, SPI, UART, I2S2, I2S3, and GP[31:27, 20:18] Pin Multiplexing
PDINHIBR3
REGISTER
BIT
FIELDS (1)
EBSR PPMODE BITS
PIN NAME
LCD_EN_RDB/SPI_CLK
MODE 2
MODE 3
MODE 4
MODE 5
MODE 6
000
001
010
011
100
101
110
PRODUCT PREVIEW
LCD_EN_RDB
SPI_CLK
LCD_EN_RDB
LCD_EN_RDB
LCD_EN_RDB
LCD_EN_RDB
SPI_CLK
LCD_D[0]
SPI_RX
LCD_D[0]
LCD_D[0]
LCD_D[0]
LCD_D[0]
SPI_RX
LCD_D[1]/SPI_TX
LCD_D[1]
SPI_TX
LCD_D[1]
LCD_D[1]
LCD_D[1]
LCD_D[1]
SPI_TX
P2PD
LCD_D[2]/GP[12]
LCD_D[2]
GP[12]
LCD_D[2]
LCD_D[2]
LCD_D[2]
LCD_D[2]
GP[12]
P3PD
LCD_D[3]/GP[13]
LCD_D[3]
GP[13]
LCD_D[3]
LCD_D[3]
LCD_D[3]
LCD_D[3]
GP[13]
P4PD
LCD_D[4]/GP[14]
LCD_D[4]
GP[14]
LCD_D[4]
LCD_D[4]
LCD_D[4]
LCD_D[4]
GP[14]
P5PD
LCD_D[5]/GP[15]
LCD_D[5]
GP[15]
LCD_D[5]
LCD_D[5]
LCD_D[5]
LCD_D[5]
GP[15]
P6PD
LCD_D[6]/GP[16]
LCD_D[6]
GP[16]
LCD_D[6]
LCD_D[6]
LCD_D[6]
LCD_D[6]
GP[16]
P7PD
LCD_D[7]/GP[17]
LCD_D[7]
GP[17]
LCD_D[7]
LCD_D[7]
LCD_D[7]
LCD_D[7]
GP[17]
P8PD
LCD_D[8]/I2S2_CLK/GP[18]/SPI_CLK
LCD_D[8]
I2S2_CLK
GP[18]
SPI_CLK
I2S2_CLK
SPI_CLK
I2S2_CLK
P9PD
LCD_D[9]/I2S2_FS/GP[19]/SPI_CS0
LCD_D[9]
I2S2_FS
GP[19]
SPI_CS0
I2S2_FS
SPI_CS0
I2S2_FS
P10PD
LCD_D[10]/I2S2_RX/GP[20]/SPI_RX
LCD_D[10]
I2S2_RX
GP[20]
SPI_RX
I2S2_RX
SPI_RX
I2S2_RX
P11PD
LCD_D[11]/I2S2_DX/GP[27]/SPI_TX
LCD_D[11]
I2S2_DX
GP[27]
SPI_TX
I2S2_DX
SPI_TX
I2S2_DX
P12PD
LCD_D[12]/UART_RTS/GP[28]/I2S3_CLK
LCD_D[12]
UART_RTS
GP[28]
I2S3_CLK
UART_RTS
UART_RTS
I2S3_CLK
P13PD
LCD_D[13]/UART_CTS/GP[29]/I2S3_FS
LCD_D[13]
UART_CTS
GP[29]
I2S3_FS
UART_CTS
UART_CTS
I2S3_FS
P14PD
LCD_D[14]/UART_RXD/GP[30]/I2S3_RX
LCD_D[14]
UART_RXD
GP[30]
I2S3_RX
UART_RXD
UART_RXD
I2S3_RX
P15PD
LCD_D[15]/UART_TXD/GP[31]/I2S3_DX
LCD_D[15]
UART_TXD
GP[31]
I2S3_DX
UART_TXD
UART_TXD
I2S3_DX
LCD_CS0_E0/SPI_CS0
LCD_CS0_E0
SPI_CS0
LCD_CS0_E0
LCD_CS0_E0
LCD_CS0_E0
LCD_CS0_E0
SPI_CS0
LCD_CS1_E1/SPI_CS1
LCD_CS1_E1
SPI_CS1
LCD_CS1_E1
LCD_CS1_E1
LCD_CS1_E1
LCD_CS1_E1
SPI_CS1
LCD_RW_WRB
SPI_CS2
LCD_RW_WRB
LCD_RW_WRB
LCD_RW_WRB
LCD_RW_WRB
SPI_CS2
LCD_RS
SPI_CS3
LCD_RS
LCD_RS
LCD_RS
LCD_RS
SPI_CS3
LCD_RS/SPI_CS3
60
MODE 1
LCD_D[0]/SPI_RX
LCD_RW_WRB/SPI_CS2
(1)
MODE 0
The pin names with PDINHIBR3 register bit field references can have the pulldown resister enabled or disabled via this register.
Device Configuration
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
3.7.1.2
SPRS645 – JANUARY 2010
MMC1, I2S1, and GP[11:6] Pin Multiplexing [EBSR.SP1MODE Bits]
The MMC1, I2S1, and GPIO signal muxing is determined by the value of the SP1MODE bit fields in the External Bus Selection Register (EBSR)
register. For more details on the actual pin functions, see Table 3-8 .
Table 3-8. MMC1, I2S1, and GP[11:6] Pin Multiplexing
(1)
PIN NAME
MODE 0
MODE 1
MODE 2
00
01
10
S10PD
MMC1_CLK/I2S1_CLK/GP[6]
MMC1_CLK
I2S1_CLK
GP[6]
S11PD
MMC1_CMD/I2S1_FS/GP[7]
MMC1_CMD
I2S1_FS
GP[7]
S12PD
MMC1_D0/I2S1_DX/GP[8]
MMC1_D0
I2S1_DX
GP[8]
S13PD
MMC1_D1/I2S1_RX/GP[9]
MMC1_D1
I2S1_RX
GP[9]
S14PD
MMC1_D2/GP[10]
MMC1_D2
GP[10]
GP[10]
S15PD
MMC1_D3/GP[11]
MMC1_D3
GP[11]
GP[11]
PRODUCT PREVIEW
EBSR SP1MODE BITS
PDINHIBR1
REGISTER
BIT FIELDS (1)
The pin names with PDINHIBR1 register bit field references can have the pulldown register enabled or disabled via this register.
Device Configuration
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
61
TMS320C5515
SPRS645 – JANUARY 2010
3.7.1.3
www.ti.com
MMC0, I2S0, and GP[5:0] Pin Multiplexing [EBSR.SP0MODE Bits]
The MMC0, I2S0, and GPIO signal muxing is determined by the value of the SP0MODE bit fields in the
External Bus Selection Register (EBSR) register. For more details on the actual pin functions, see
Table 3-9.
Table 3-9. MMC0, I2S0, and GP[5:0] Pin Multiplexing
EBSR SP0MODE BITS
PDINHIBR1
REGISTER
BIT FIELDS (1)
(1)
PIN NAME
MODE 0
MODE 1
MODE 2
00
01
10
S00PD
MMC0_CLK/I2S0_CLK/GP[0]
MMC0_CLK
I2S0_CLK
GP[0]
S01PD
MMC0_CMD/I2S0_FS/GP[1]
MMC0_CMD
I2S0_FS
GP[1]
S02PD
MMC0_D0/I2S0_DX/GP[2]
MMC0_D0
I2S0_DX
GP[2]
S03PD
MMC0_D1/I2S0_RX/GP[3]
MMC0_D1
I2S0_RX
GP[3]
S04PD
MMC0_D2/GP[4]
MMC0_D2
GP[4]
GP[4]
S05PD
MMC0_D3/GP[5]
MMC0_D3
GP[5]
GP[5]
The pin names with PDINHIBR1 register bit field references can have the pulldown register enabled or disabled via this register.
3.7.1.4
EMIF EM_A[20:15] and GP[26:21] Pin Multiplexing [EBSR.Axx_MODE bits]
PRODUCT PREVIEW
The EMIF Address and GPIO signal muxing is determined by the value of the A20_MODE, A19_MODE,
A18_MODE, A17_MODE, A16_MODE, and A15_MODE bit fields in the External Bus Selection Register
(EBSR) register. For more details on the actual pin functions, see Table 3-10.
Table 3-10. EM_A[20:16] and GP[26:21] Pin Multiplexing
PIN NAME
Axx_MODE BIT
0
1
EM_A[15]/GP[21]
EM_A[15]
GP[21]
EM_A[16]/GP[22]
EM_A[16]
GP[22]
EM_A[17]/GP[23]
EM_A[17]
GP[23]
EM_A[18]/GP[24]
EM_A[18]
GP[24]
EM_A[19]/GP[25]
EM_A[19]
GP[25]
EM_A[20]/GP[26]
EM_A[20]
GP[26]
3.8
3.8.1
Debugging Considerations
Pullup/Pulldown Resistors
Proper board design should ensure that input pins to the C5515 DSP always be at a valid logic level and
not floating. This may be achieved via pullup/pulldown resistors. The DSP features internal pullup (IPU)
and internal pulldown (IPD) resistors on many pins, including all GPIO pins, to eliminate the need, unless
otherwise noted, for external pullup/pulldown resistors.
An external pullup/pulldown resistor may need to be used in the following situations:
• Configuration Pins: An external pullup/pulldown resistor is recommended to set the desired value/state
(see the configuration pins listed in Table 3-5, Default Functions Affected by Device Configuration
Pins). Note that some configuration pins must connected directly to ground or to a specific supply
voltage.
• Other Input Pins: If the IPU/IPD does not match the desired value/state, use an external
pullup/pulldown resistor to pull the signal to the opposite rail.
62
Device Configuration
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
For the configuration pins (listed in Table 3-5, Default Functions Affected by Device Configuration Pins), if
they are both routed out and 3-stated (not driven), it is strongly recommended that an external
pullup/pulldown resistor be implemented. In addition, applying external pullup/pulldown resistors on the
configuration pins adds convenience to the user in debugging and flexibility in switching operating modes.
Tips for choosing an external pullup/pulldown resistor:
• Consider the total amount of current that may pass through the pullup or pulldown resistor. Make sure
to include the leakage currents of all the devices connected to the net, as well as any internal pullup or
pulldown (IPU/IPD) resistors.
• Decide a target value for the net. For a pulldown resistor, this should be below the lowest VIL level of
all inputs connected to the net. For a pullup resistor, this should be above the highest VIH level of all
inputs on the net. A reasonable choice would be to target the VOL or VOH levels for the logic family of
the limiting device; which, by definition, have margin to the VIL and VIH levels.
• Select a pullup/pulldown resistor with the largest possible value; but, which can still ensure that the net
will reach the target pulled value when maximum current from all devices on the net is flowing through
the resistor. The current to be considered includes leakage current plus, any other internal and
external pullup/pulldown resistors on the net.
• For bidirectional nets, there is an additional consideration which sets a lower limit on the resistance
value of the external resistor. Verify that the resistance is small enough that the weakest output buffer
can drive the net to the opposite logic level (including margin).
• Remember to include tolerances when selecting the resistor value.
• For pullup resistors, also remember to include tolerances on the DVDD rail.
For most systems, a 1-kΩ resistor can be used to oppose the IPU/IPD while meeting the above criteria.
Users should confirm this resistor value is correct for their specific application.
For most systems, a 20-kΩ resistor can be used to compliment the IPU/IPD on the configuration pins
while meeting the above criteria. Users should confirm this resistor value is correct for their specific
application.
For more detailed information on input current (II), and the low-/high-level input voltages (VIL and VIH) for
the C5515 DSP, see Section 4.3, Electrical Characteristics Over Recommended Ranges of Supply
Voltage and Operating Temperature.
For the internal pullup/pulldown resistors for all device pins, see the peripheral/system-specific terminal
functions table in this document.
3.8.2
Bus Holders
The C5515 has special I/O bus-holder structures to ensure pins are not left floating when CVDD power is
removed while I/O power is applied. When CVDD is "ON", the bus-holders are disabled and the internal
pullups or pulldowns, if applicable, function normally. But when CVDD is "OFF" and the I/O supply is "ON",
the bus-holders become enabled and any applicable internal pullups and pulldowns are disabled.
The bus-holders are weak drivers on the pin and, for as long as CVDD is "OFF" and I/O power is "ON",
they hold the last state on the pin. If an external device is strongly driving C5515 I/O pin to the opposite
state then the bus-holder will flip state to match the external driver and DC current will stop.
This bus-holder feature prevents unnecessary power consumption when CVDD is "OFF"and I/O supply is
"ON". For example, current caused by undriven pins (input buffer oscillation) and/or DC current flowing
through pullups or pulldowns.
Device Configuration
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
63
PRODUCT PREVIEW
When an external pullup or pulldown resistor is used on a pin, the pin’s internal pullup or pulldown resistor
should be disabled through the Pullup/Pulldown Inhibit Registers (PDINHIBR1/2/3) [1C17h, 1C18h, and
1C19h, respectively] to minimize power consumption.
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
If external pullup or pulldown resistors are implemented, then care should be taken that those
pullup/pulldown resistors can exceed the internal bus-holder's max current and thereby cause the
bus-holder to flip state to match the state of the external pullup or pulldown. Otherwise, DC current will
flow unnecessarily. When CVDD power is applied, the bus holders are disabled (for further details on bus
holders, see Section 5.3.2,Digital I/O Behavior When Core Power (CVDD) is Down..
3.8.3
CLKOUT Pin
For debug purposes, the DSP includes a CLKOUT pin which can be used to tap different clocks within the
clock generator. The SRC bits of the CLKOUT Control Source Register (CCSSR) can be used to specify
the source for the CLKOUT pin.
Note: the bootloader disables the CLKOUT pin via CLKOFF bit in the ST3_55 CPU register.
For more information on the ST3_55 CPU register, see the TMS320C55x 3.0 CPU Reference Guide
(literature number: SWPU073).
PRODUCT PREVIEW
64
Device Configuration
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
4 Device Operating Conditions
For the device maximum operating frequency, see Section 2.6.2, Device and Development-Support Tool
Nomenclature.
Absolute Maximum Ratings Over Operating Case Temperature Range (Unless
Otherwise Noted) (1)
Supply voltage ranges:
Input and Output voltage ranges:
Operating case temperature ranges, Tc:
Digital Core (CVDD, CVDDRTC, USB_VDD1P3) (2)
–0.5 V to 1.7 V
I/O, 1.8 V, 2.5 V, 2.8 V, 3.3 V (DVDDIO, DVDDEMIF,
DVDDRTC) 3.3V USB supplies USB PHY (USB_VDDOSC,
USB_VDDPLL, USB_VDDA3P3) (2)
–0.5 V to 4.2 V
LDOI
–0.5 V to 4.2 V
Analog, 1.3 V (VDDA_PLL, USB_VDDA1P3, VDDA_ANA) (2)
–0.5 V to 1.7 V
VI I/O, All pins with DVDDIO or DVDDEMIF or USB_VDDOSC
or USB_VDDPLLor USB_VDDA3P3 as supply source
–0.5 V to 4.2 V
VO I/O, All pins with DVDDIO or DVDDEMIF or
USB_VDDOSCor USB_VDDPLLor USB_VDDA3P3 as supply
source
–0.5 V to 4.2 V
RTC_XI and RTC_XO
–0.5 V to 1.7 V
VI and VO, GPAIN[0]
–0.5 V to 4.2 V
VI and VO, GPAIN[3:1]
–0.5 V to 1.7 V
VO, BG_CAP
–0.5 V to 1.7 V
ANA_LDOO, DSP_LDOO, and USB_LDOO
–0.5 V to 1.7 V
Commercial Temperature (default)
Industrial Temperature
0°C to 70°C
-40°C to 85°C
Storage temperature range, Tstg
(default)
Device Operating Life
Power-On Hours (POH)
Commercial Temperature
100, 000 POH
Industrial Temperature
100, 000 POH
(1)
(2)
–65°C to 150°C
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values are with respect to VSS.
Device Operating Conditions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
65
PRODUCT PREVIEW
4.1
TMS320C5515
SPRS645 – JANUARY 2010
4.2
www.ti.com
Recommended Operating Conditions
Core Supplies
MIN
NOM
MAX
UNIT
0.998
1.05
1.15
V
1.24
1.3
1.43
V
0.998
1.05
1.43
V
CVDD
Supply voltage, Digital Core
CVDDRTC
Supply voltage, RTC and RTC OSC
USB_VDD1P3
Supply voltage, Digital USB
1.24
1.3
1.43
V
USB_VDDA1P3
Supply voltage, 1.3 V Analog USB
1.24
1.3
1.43
V
VDDA_ANA
Supply voltage, 1.3 V SAR and Pwr Mgmt
1.24
1.3
1.43
V
VDDA_PLL
Supply voltage, 1.3 V System PLL
1.24
1.3
1.43
V
USB_VDDPLL
Supply voltage, 3.3 V USB PLL
2.97
3.3
3.63
V
Supply voltage, I/O, 3.3 V
2.97
3.3
3.63
V
Supply voltage, I/O, 2.8 V
2.52
2.8
3.08
V
Supply voltage, I/O, 2.5 V
2.25
2.5
2.75
V
Supply voltage, I/O, 1.8 V
1.65
1.8
1.98
V
USB_VDDOSC
Supply voltage, I/O, 3.3 V USB OSC
2.97
3.3
3.63
V
USB_VDDA3P3
Supply voltage, I/O, 3.3 V Analog USB PHY
2.97
3.3
3.63
V
LDOI
Supply voltage, Analog Pwr Mgmt and LDO Inputs
3.6
V
VSS
Supply ground, Digital I/O
VSSRTC
Supply ground, RTC
USB_VSSOSC
Supply ground, USB OSC
USB_VSSPLL
Supply ground, USB PLL
USB_VSSA3P3
Supply ground, 3.3 V Analog USB PHY
USB_VSSA1P3
Supply ground, USB 1.3 V Analog USB PHY
0
V
USB_VSSREF
Supply ground, USB Reference Current
VSSA_PLL
Supply ground, System PLL
USB_VSS1P3
Supply ground, 1.3 V Digital USB PHY
VSSA_ANA
Supply ground, SAR and Pwr Mgmt
DVDDIO
DVDDEMIF
DVDDRTC
I/O Supplies
PRODUCT PREVIEW
GND
60 or 75 MHz
100 or 120 MHz
32.768 KHz
1.8
0
0
VIH
(1)
High-level input voltage, 3.3, 2.8, 2.5, 1.8 V I/O (except
GPAIN[3:0] pins) (2)
0.7 * DVDD
DVDD + 0.3
V
VIL
(1)
Low-level input voltage, 3.3, 2.8, 2.5, 1.8 V I/O (except
GPAIN[3:0] pins) (2)
-0.3
0.3 * DVDD
V
(3)
-0.3
3.6
V
-0.3
VDDA_ANA + 0.3
V
0
70
°C
Input voltage, GPAIN0 pin
VIN
Input voltage, GPAIN[3:1] pins
Tc
Operating case temperature
Default
(Commercial)
(Industrial)
FSYSCLK1
(1)
(2)
(3)
66
DSP Operating Frequency (SYSCLK1)
-40
85
1.05 V
0
60 or 75
MHz
°C
1.3 V
0
100 or 120
MHz
DVDD refers to the pin I/O supply voltage. To determine the I/O supply voltage for each pin, see Section 2.5 , Terminal Functions.
The I2C pin SDA and SCL do not feature fail-safe I/O buffers. These pin could potentially draw current when the DVDDIO is powered
down. Due to the fact that different voltage devices can be connected to I2C bus and the I2C inputs are LVCMOS, the level of logic 0
(low) and logic 1 (high) are not fixed and depend on DVDDIO.
The GNDON bit in the SARPINCTRL register should be set to "1" before SAR channels 0, 1, or 2 are enabled via the CHSEL bit in the
SARCTRL register, when VIN greater than VDDA_ANA.
Device Operating Conditions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
Electrical Characteristics Over Recommended Ranges of Supply Voltage and
Operating Temperature (Unless Otherwise Noted)
PARAMETER
VOH
VOL
VHYS
(6) (7)
(6) (7)
IIH/
IIL (7)
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
MAX
High speed: USB_DN and
USB_DP (2)
360
440
UNIT
V
mV
High-level output voltage, 3.3, 2.8,
2.5, 1.8 V I/O (except GPAIN[3:0]
pins)
IO = IOH
0.8 * DVDD
V
High-level output voltage,
GPAIN[3:1] pins
IO = IOH
0.8 * VDDA_ANA
V
Full speed: USB_DN and
USB_DP (2)
0.0
0.3
V
High speed: USB_DN and
USB_DP (2)
–10
10
mV
Low-level output voltage, 3.3, 2.8,
2.5, 1.8V I/O (except I2C and
GPAIN[3:0] pins)
IO = IOL
Low-level output voltage, I2C
pins (3)
VDD > 2 V, IO L = 3 mA
Low-level output voltage,
GPAIN[3:0] pins
IO = IOL
(4)
0
0.2 * DVDD
V
0.4
V
0.2 * VDDA_ANA
V
DVDD = 3.3 V
162
mV
DVDD = 2.5 V
141
mV
DVDD = 1.8 V
122
mV
USB_LDOO voltage
TBD
1.3
1.43
V
ANA_LDOO voltage
TBD
1.3
1.43
V
DSP_LDO_V bit in the LDOCNTL register = 1
TBD
1.3
1.43
V
DSP_LDO_V bit in the LDOCNTL register = 0
TBD
1.05
1.15
DSP_LDO shutdown current (5)
LDOI = VMIN
TBD
mA
ANA_LDO shutdown current (5)
LDOI = VMIN
TBD
mA
USB_LDO shutdown current (5)
LDOI = VMIN
TBD
Input current [DC] (except
WAKEUP, I2C, and GPAIN[3:0]
pins)
Input current [DC] (except
WAKEUP, I2C, and GPAIN[3:0]
pins
Input current [DC], ALL pins
V
mA
-5
+5
mA
DVDD = 3.3 V with internal pullup enabled (8)
-59 to -161
mA
DVDD = 2.5 V with internal pullup enabled (8)
-31 to -93
mA
DVDD = 1.8 V with internal pullup enabled (8)
-14 to -44
Input only pin, internal pulldown or pullup disabled
IIHPD
TYP
USB_VDDA3P3
Input only pin, internal pulldown or pullup disabled
IILPU
MIN
2.8
DSP_LDOO voltage
ISD
(1)
Full speed: USB_DN and
USB_DP (2)
Input hysteresis
VLDO
TEST CONDITIONS
-5
mA
+5
mA
DVDD = 3.3 V with internal pulldown enabled (8)
52 to 158
mA
DVDD = 2.5 V with internal pulldown enabled (8)
27 to 83
mA
DVDD = 1.8 V with internal pulldown enabled (8)
11 to 35
mA
VI = VSS to DVDD with internal pullups and pulldowns
disabled.
-5
PRODUCT PREVIEW
4.3
SPRS645 – JANUARY 2010
+5
mA
For test conditions shown as MIN, MAX, or TYP, use the appropriate value specified in the recommended operating conditions table.
The USB I/Os adhere to the Universal Bus Specification Revision 2.0 (USB2.0 spec).
VDD is the voltage to which the I2C bus pullup resistors are connected.
Applies to all input pins except WAKEUP, I2C pins, GPAIN[3:0], RTC_XI, and USB_MXI.
ISD is the amount of current the LDO is ensured to deliver before shutting down to protect itself.
II applies to input-only pins and bi-directional pins. For input-only pins, II indicates the input leakage current. For bi-directional pins, II
indicates the input leakage current and off-state (Hi-Z) output leakage current.
When CVDD power is "ON", the pin bus-holders are disabled. For more detailed information, see Section 5.3.2 , Digital I/O Behavior
When Core Power (CVDD) is Down)
Applies only to pins with an internal pullup (IPU) or pulldown (IPD) resistor.
Device Operating Conditions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
67
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
Electrical Characteristics Over Recommended Ranges of Supply Voltage and Operating Temperature
(Unless Otherwise Noted) (continued)
PARAMETER
TEST CONDITIONS
(1)
All Pins (except USB, EMIF, CLKOUT, and
GPAIN[3:0] pins)
EMIF pins
IOH
(7)
High-level output current [DC]
CLKOUT pin
GPAIN[3:1] pins
(GPAIN0 is open-drain
and cannot drive high)
MIN
IOL (7)
Low-level output current [DC]
CLKOUT pin
PRODUCT PREVIEW
GPAIN[3:0]
IOZ
(10)
I/O Off-state output current
MAX
mA
DVDD = 3.3 V
-6
mA
DVDD = 1.8 V
-5
mA
DVDD = 3.3 V
-6
mA
DVDD = 1.8 V
-4
mA
DVDD = VDDA_ANA = 1.3 V,
External Regulator (9)
-4
mA
DVDD = VDDA_ANA = 1.3 V,
Internal Regulator (9)
-100
mA
+4
mA
DVDD = 3.3 V
+6
mA
DVDD = 1.8 V
+5
mA
DVDD = 3.3 V
+6
mA
DVDD = 1.8 V
+4
mA
DVDD = VDDA_ANA = 1.3 V,
external regulator
+4
mA
DVDD = VDDA_ANA = 1.3 V,
internal regulator (9)
+4
mA
mA
All Pins (except USB and GPAIN[3:0])
-10
+10
GPAIN[3:0] pins
-10
+10
IOLBH
Bus Holder pull low current when CVDD is powered "OFF"
IOHBH
Bus Holder pull high current when CVDD is powered "OFF"
UNIT
-4
All Pins (except USB, EMIF, CLKOUT, and
GPAIN[3:0] pins)
EMIF pins
TYP
+TBD
mA
mA
-TBD
mA
(9)
When the ANA_LDO supplies VDDA_ANA, it is not recommended to use the GPAIN[3:1] signals for general-purpose outputs (driving high).
The ISD parameter of the ANA_LDO is too low to drive any realistic load on the GPAIN[3:1] pins while also supplying the PLL through
VDDA_PLL and the SAR through VDDA_ANA.
(10) IOZ applies to output-only pins, indicating off-state (Hi-Z) output leakage current.
68
Device Operating Conditions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Electrical Characteristics Over Recommended Ranges of Supply Voltage and Operating Temperature
(Unless Otherwise Noted) (continued)
PARAMETER
TEST CONDITIONS
(1)
MIN
TYP
MAX
UNIT
0.22
mW/MHz
Active, CVDD = 1.05 V, DSP clock = 60 or 75 MHz
Room Temp (25 °C), 75% DMAC + 25% ADD
(typical data switching)
0.15
mW/MHz
Active, CVDD = 1.3 V, DSP clock = 100 or 120 MHz
Room Temp (25 °C), 75% DMAC + 25% NOP
(typical sine wave data switching)
0.22
mW/MHz
Active, CVDD = 1.05 V, DSP clock = 60 or 75 MHz
Room Temp (25 °C), 75% DMAC + 25% NOP
(typical data switching)
0.14
mW/MHz
Active, CVDD = 1.3 V, DSP clock = 100 or 120 MHz
Room Temp (25 °C), Hardware FFT Accelerator
1024-pt FFT, ROM execution
0.31
mW/MHz
Active, CVDD = 1.05 V, DSP clock = 60 or 75 MHz
Room Temp (25 °C), Hardware FFT Accelerator
1024-pt FFT, ROM execution
0.25
mW/MHz
Standby, CVDD = 1.3 V, Master clock disabled,
Room Temp (25 °C), DARAM and SARAM in active
mode
0.44
mW
Standby, CVDD = 1.05 V, Master clock disabled,
Room Temp (25 °C), DARAM and SARAM in active
mode
0.26
mW
Standby, CVDD = 1.3 V, Master clock disabled,
Room Temp (25 °C), DARAM in retention and
SARAM in active mode
0.40
mW
Standby, CVDD = 1.05 V, Master clock disabled,
Room Temp (25 °C), DARAM in retention and
SARAM in active mode
0.23
mW
Standby, CVDD = 1.3 V, Master clock disabled,
Room Temp (25 °C), DARAM in active mode and
SARAM in retention
0.28
mW
Standby, CVDD = 1.05 V, Master clock disabled,
Room Temp (25 °C), DARAM in active mode and
SARAM in retention
0.15
mW
Analog PLL (VDDA_PLL) supply
current
VDDA_PLL = 1.37 V
Room Temp (25 °C), Phase detector = 170 kHz,
VCO = 120 MHz
0.7
SAR Analog (VDDA_ANA) supply
current
VDDA_ANA = 1.37 V, SAR clock = 2 MHz, Temp
(70 °C)
Core (CVDD) supply current
ICDD
1.2
mA
1
mA
CI
Input capacitance
4
pF
Co
Output capacitance
4
pF
Device Operating Conditions
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
PRODUCT PREVIEW
Active, CVDD = 1.3 V, DSP clock = 100 or 120 MHz
Room Temp (25 °C), 75% DMAC + 25% ADD
(typical sine wave data switching)
69
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
5 Peripheral Information and Electrical Specifications
5.1
Parameter Information
Tester Pin Electronics
42 Ω
Data Sheet Timing Reference Point
3.5 nH
Output
Under
Test
Transmission Line
Z0 = 50 Ω
(see Note)
4.0 pF
Device Pin
(see Note)
1.85 pF
NOTE: The data sheet provides timing at the device pin. For output timing analysis, the tester pin electronics and its transmission line effects must be
taken into account. A transmission line with a delay of 2 ns can be used to produce the desired transmission line effect. The transmission line is
intended as a load only. It is not necessary to add or subtract the transmission line delay (2 ns) from the data sheet timings.
Input requirements in this data sheet are tested with an input slew rate of < 4 Volts per nanosecond (4 V/ns) at the device pin.
PRODUCT PREVIEW
Figure 5-1. 3.3-V Test Load Circuit for AC Timing Measurements
The load capacitance value stated is only for characterization and measurement of AC timing signals. This
load capacitance value does not indicate the maximum load the device is capable of driving.
5.1.1
1.8-V, 2.5-V, 2.8-V, and 3.3-V Signal Transition Levels
All rise and fall transition timing parameters are referenced to VIL MAX and VIH MIN for input clocks, VOL
MAX and VOH MIN for output clocks.
Vref = VIH MIN (or VOH MIN)
Vref = VIL MAX (or VOL MAX)
Figure 5-2. Rise and Fall Transition Time Voltage Reference Levels
5.1.2
3.3-V Signal Transition Rates
All timings are tested with an input edge rate of 4 volts per nanosecond (4 V/ns).
5.1.3
Timing Parameters and Board Routing Analysis
The timing parameter values specified in this data manual do not include delays by board routings. As a
good board design practice, such delays must always be taken into account. Timing values may be
adjusted by increasing/decreasing such delays. TI recommends utilizing the available I/O buffer
information specification (IBIS) models to analyze the timing characteristics correctly. To properly use IBIS
models to attain accurate timing analysis for a given system, see the Using IBIS Models for Timing
Analysis application report (literature number SPRA839). If needed, external logic hardware such as
buffers may be used to compensate any timing differences.
5.2
Recommended Clock and Control Signal Transition Behavior
All clocks and control signals must transition between VIH and VIL (or between VIL and VIH) in a monotonic
manner.
70
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
5.3
SPRS645 – JANUARY 2010
Power Supplies
The C5515 includes four core voltage-level supplies (CVDD, CVDDRTC, USB_VDD1P3, USB_VDDA1P3), and
several I/O supplies (DVDDIO, DVDDEMIF, DVDDRTC, USB_VDDOSC, and USB_VDDA3P3), as well as several
analog supplies (LDOI, VDDA_PLL, VDDA_ANA, and USB_VDDPLL). Some TI power-supply devices include
features that facilitate power sequencing—for example, Auto-Track and Slow-Start/Enable features. For
more information regarding TI's power management products and suggested devices to power TI DSPs,
visit www.ti.com/processorpower.
5.3.1
Power-Supply Sequencing
The C5515 includes four core voltage-level supplies (CVDD, CVDDRTC, USB_VDD1P3, USB_VDDA1P3), and
several I/O supplies including—LDOI, DVDDIO, DVDDEMIF, DVDDRTC, USB_VDDOSC, and USB_VDDA3P3
The I/O design allows either the core supplies (CVDD, CVDDRTC, USB_VDD1P3, USB_VDDA1P3) or the I/O
supplies (LDOI, DVDDIO, DVDDEMIF, DVDDRTC, USB_VDDOSC, and USB_VDDA3P3) to be powered up for an
indefinite period of time while the other supply is not powered if the following constraints are met:
1. All maximum ratings and recommended operating conditions are satisfied.
2. All warnings about exposure to maximum rated and recommended conditions, particularly junction
temperature are satisfied. These apply to power transitions as well as normal operation.
3. Bus contention while core supplies are powered must be limited to 100 hours over the projected
lifetime of the device.
4. Bus contention while core supplies are powered down does not violate the absolute maximum ratings.
If the USB subsystem is not used, the USB Core (USB_VDD1P3, USB_VDDA1P3) and USB PHY and I/O level
supplies (USB_VDDOSC, USB_VDDA3P3, and USB_VDDPLL) can be powered off.
Note: If the device is powered up with the USB cable connected to an active USB host and the USB PHY
(USB_VDDA3P3) is powered up before the USB Core (USB_VDD1P3,USB_VDDA1P3), the USB Core must be
powered within 100 msec after the USB host detects the device has been attached.
A supply bus is powered up when the voltage is within the recommended operating range. It is powered
down when the voltage is below that range, either stable or while in transition.
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
71
PRODUCT PREVIEW
The C5515 does not require a specific power-up sequence. However, if the DSP_LDO is disabled
(DSP_LDO_EN = high) and an external regulator supplies power to the CPU Core (CVDD), the external
reset signal (RESET) must be held asserted until all of the supply voltages reach their valid operating
ranges.
TMS320C5515
SPRS645 – JANUARY 2010
5.3.2
www.ti.com
Digital I/O Behavior When Core Power (CVDD) is Down
With some exceptions (listed below), all digital I/O pins on the C5515 have special features to allow
powering down of the Digital Core Domain (CVDD) without causing I/O contentions or floating inputs at the
pins (see Figure 5-3). The C5515 device asserts the internal signal called HHV high when power has been
removed from the Digital Core Domain (CVDD). Asserting the internal HHV signal causes the following
conditions to occur in any order:
• All output pin strong drivers to go to the high-impedance (Hi-Z) state
• Weak bus holders to be enabled to hold the pin at a valid high or low
• The internal pullups or pulldowns (IPUs/IPDs) on the I/O pins will be disabled
The exception pins that do not have this special feature are:
• Pins driven by the CVDD_RTC Power Domain [This power domain is "Always On"; therefore, the pins
driven by CVDD_RTC do not need these special features]:
– RTC_XI, RTC_XO, RTC_CLKOUT, and WAKEUP
• USB Pins:
– USB_DP, USB_DM, USB_R1, USB_VBUS, USB_MXI, and USB_MXO
• Pins for the Analog Block:
– GPAIN[3:0], DSP_LDO_EN, and BG_CAP
PRODUCT PREVIEW
DVDD
Y
PAD
A
GZ
hhvgz
HHV
OR
HHV
PI
OR
hhvpi
HHV
Figure 5-3. Bus Holder I/O Circuit
72
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
5.3.3
SPRS645 – JANUARY 2010
Power-Supply Design Considerations
Core and I/O supply voltage regulators should be located close to the DSP (or DSP array) to minimize
inductance and resistance in the power delivery path. Additionally, when designing for high-performance
applications utilizing the C5515 device, the PC board should include separate power planes for core, I/O,
VDDA_ANA and VDDA_PLL (which can share the same PCB power plane), and ground; all bypassed with
high-quality low-ESL/ESR capacitors.
5.3.4
Power-Supply Decoupling
In order to properly decouple the supply planes from system noise, place capacitors (caps) as close as
possible to the C5515 . These caps need to be no more than 1.25 cm maximum distance from the C5515
power pins to be effective. Physically smaller caps, such as 0402, are better but need to be evaluated
from a yield/manufacturing point-of-view. Parasitic inductance limits the effectiveness of the decoupling
capacitors, therefore physically smaller capacitors should be used while maintaining the largest available
capacitance value.
As with the selection of any component, verification of capacitor availability over the product's production
lifetime should be considered.
On the C5515 the recommended decoupling capacitance for the DSP core supplies should be 1 mF in
parallel with 0.01-mF capacitor per supply pin.
5.3.5
LDO Input Decoupling
The LDO inputs should follow the same decoupling guidelines as other power-supply pins above.
5.3.6
LDO Output Decoupling
The LDO circuits implement a voltage feedback control system which has been designed to optimize gain
and stability tradeoffs. As such, there are design assumptions for the amount of capacitance on the LDO
outputs. For proper device operation, the following external decoupling capacitors should be used when
the on-chip LDOs are enabled:
• ANA_LDOO– 1mF
• DSP_LDOO – 5mF ~ 10mF
• USB_LDOO – 1mF ~ 2mF
5.4
External Clock Input From RTC_XI, CLKIN, and USB_MXI Pins
The C5515 DSP includes two options to provide an external clock input to the system clock generator:
• Use the on-chip real-time clock (RTC) oscillator with an external 32.768-kHz crystal connected to the
RTC_XI and RTC_XO pins.
• Use an external 11.2896-, 12.0-, or 12.288-MHz LVCMOS clock input fed into the CLKIN pin that
operates at the same voltage as the DVDDIO supply (1.8-, 2.5-, 2.8-, or 3.3-V).
The CLK_SEL pin determines which input is used as the clock source for the system clock generator, For
more details, see Section 3.5.1, Device and Peripheral Configurations at Device Reset. The crystal for the
RTC oscillator is not required if CLKIN is used as the system reference clock; however, the RTC must still
be powered. The RTC registers starting at I/O address 1900h will not be accessible without an RTC clock.
This includes the RTC Power Management Register which provides control to the on-chip LDOs and
WAKEUP and RTC_CLKOUT pins. Section 5.4.1, Real-Time Clock (RTC) On-Chip Oscillator With
External Crystal provides more details on using the RTC on-chip oscillator with an external crystal.
Section 5.4.2, CLKIN Pin With LVCMOS-Compatible Clock Input provides details on using an external
LVCMOS-compatible clock input fed into the CLKIN pin.
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
73
PRODUCT PREVIEW
Larger caps for each supply can be placed further away for bulk decoupling. Large bulk caps (on the order
of 10 mF) should be furthest away, but still as close as possible. Large caps for each supply should be
placed outside of the BGA footprint.
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
Additionally, the USB requires a reference clock generated using a dedicated on-chip oscillator with a
12-MHz external crystal connected to the USB_MXI and USB_MXO pins. The USB reference clock is not
required if the USB peripheral is not being used. Section 5.4.3, USB On-Chip Oscillator With External
Crystal provides details on using the USB on-chip oscillator with an external crystal.
5.4.1
Real-Time Clock (RTC) On-Chip Oscillator With External Crystal
The on-chip oscillator requires an external 32.768-kHz crystal connected across the RTC_XI and RTC_XO
pins, along with two load capacitors, as shown in Figure 5-4. The external crystal load capacitors must be
connected only to the RTC oscillator ground pin (VSSRTC). Do not connect to board ground (VSS). Position
the VSS lead on the board between RTC_XI and RTC_XO as a shield to reduce direct capacitance
between RTC_XI and RTC_XO leads on the board. The CVDDRTC pin can be connected to the same
power supply as CVDD , or may be connected to a different supply that meets the recommended operating
conditions (see Section 4.2), if desired.
PRODUCT PREVIEW
RTC_XI
RTC_XO
VSSRTC
VSS
CVDDRTC
CVDD
Crystal
32.768 kHz
C1
C2
0.998-1.43 V
1.05/1.3 V
Figure 5-4. 32.768-kHz RTC Oscillator
The crystal should be in fundamental-mode function, and parallel resonant, with a maximum effective
series resistance (ESR) specified in Table 5-1. The load capacitors, C1 and C2, are the total capacitance
of the circuit board and components, excluding the IC and crystal. The load capacitors values are usually
approximately twice the value of the crystal's load capacitance, CL, which is specified in the crystal
manufacturer's datasheet and should be chosen such that the equation is satisfied. All discrete
components used to implement the oscillator circuit should be placed as close as possible to the
associated oscillator pins (RTC_XI and RTC_XO) and to the VSSRTC pin.
CL =
C1 C2
(C1 + C2 )
Table 5-1. Input Requirements for Crystal on the 32.768-kHz RTC Oscillator
PARAMETER
Start-up time (from power up until oscillating at stable frequency of
32.768-kHz) (1)
Oscillation frequency
(1)
74
MIN
NOM
0.2
MAX
2
32.768
UNIT
sec
kHz
ESR
100
Maximum shunt capacitance
1.6
kΩ
pF
Maximum crystal drive
1.0
mW
The startup time is highly dependent on the ESR and the capacitive load of the crystal.
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
5.4.2
SPRS645 – JANUARY 2010
CLKIN Pin With LVCMOS-Compatible Clock Input (Optional)
Note: If CLKIN is not used, the pin must be tied low.
A LVCMOS-compatible clock input of a frequency less than 24 MHz can be fed into the CLKIN pin for use
by the DSP system clock generator. The external connections are shown in Figure 5-5 and Figure 5-6.
The bootloader assumes that the CLKIN pin is connected to the LVCMOS-compatible clock source with a
frequency of 11.2896-, 12.0-, or 12.288-MHz. These frequencies were selected to support boot mode
peripheral speeds of 500 KHz for SPI and 400 KHz for I2C. These clock frequencies are achieved by
dividing the CLKIN value by 25 for SPI and by 32 for I2C. If a faster external clock is input, then these
boot modes will run at faster clock speeds. If the system design utilizes faster peripherals or these boot
modes are not used, CLKIN values higher than 12.288 MHz can be used. Note: the CLKIN pin operates
at the same voltage as the DVDDIO supply (1.8-, 2.5-, 2.8-, or 3.3-V).
In this configuration the RTC oscillator can be optionally disabled by connecting RTC_XI to CVDDRTC and
RTC_XO to ground (VSS). However, when the RTC oscillator is disabled the RTC registers starting at I/O
address 1900h will not be accessible. This includes the RTC Power Management Register which provides
control to the on-chip LDOs and WAKEUP and RTC_CLKOUT pins. Note: the RTC must still be powered
even if the RTC oscillator is disabled.
RTC_XI
CLKIN
RTC_XO
VSSRTC
CVDDRTC
VSS
PRODUCT PREVIEW
For more details on the RTC on-chip oscillator, see Section 5.4.1, Real-Time Clock (RTC) On-Chip
Oscillator With External Crystal.
CVDD
Crystal
32.768 kHz
C1
C2
0.998-1.43 V
1.05/1.3 V
Figure 5-5. LVCMOS-Compatible Clock Input With RTC Oscillator Enabled
CLKIN
RTC_XI
CVDDRTC
RTC_XO
VSS
VSSRTC
0.998-1.43 V
CVDD
1.05/1.3 V
Figure 5-6. LVCMOS-Compatible Clock Input With RTC Oscillator Disabled
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
75
TMS320C5515
SPRS645 – JANUARY 2010
5.4.3
www.ti.com
USB On-Chip Oscillator With External Crystal (Optional)
When using the USB, the USB on-chip oscillator requires an external 12-MHz crystal connected across
the USB_MXI and USB_MXO pins, along with two load capacitors, as shown in Figure 5-7. The external
crystal load capacitors must be connected only to the USB oscillator ground pin (USB_VSSOSC). Do not
connect to board ground (VSS). The USB_VDDOSC pin can be connected to the same power supply as
USB_VDDA3P3.
The USB on-chip oscillator can be permanently disabled, via tie-offs, if the USB peripheral is not being
used. To permanently disable the USB oscillator, connect the USB_MXI pin to ground (VSS) and leave the
USB_MXO pin unconnected. The USB oscillator power pins (USB_VDDOSC and USB_VSSOSC) should also
be connected to ground.
USB_MXI
USB_MXO
USB_VSSOSC
USB_VDDOSC
VSS
USB_VDDA3P3
Crystal
12 MHz
PRODUCT PREVIEW
C1
C2
3.3 V
3.3 V
Figure 5-7. 12-MHz USB Oscillator
76
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
The crystal should be in fundamental-mode operation, and parallel resonant, with a maximum effective
series resistance (ESR) specified in Table 5-2. The load capacitors, C1 and C2 are the total capacitance
of the circuit board and components, excluding the IC and crystal. The load capacitor value is usually
approximately twice the value of the crystal's load capacitance, CL, which is specified in the crystal
manufacturer's datasheet and should be chosen such that the equation below is satisfied. All discrete
components used to implement the oscillator circuit should be placed as close as possible to the
associated oscillator pins (USB_MXI and USB_MXO) and to the USB_VSSOSC pin.
CL =
C1 C2
(C1 + C2 )
Table 5-2. Input Requirements for Crystal on the 12-MHz USB Oscillator
MIN
Start-up time (from power up until oscillating at stable frequency of
12 MHz) (1)
Oscillation frequency
NOM
MAX
0.100
10
12
ms
MHz
ESR
(2)
Frequency stability
Maximum shunt capacitance
Maximum crystal drive
(1)
(2)
UNIT
100
Ω
±100
ppm
5
pF
330
mW
The startup time is highly dependent on the ESR and the capacitive load of the crystal.
If the USB is used, a 12-MHz, ±100-ppm crystal is recommended.
5.5
Clock PLLs
The C5515 DSP uses a software-programmable PLL to generate frequencies required by the CPU, DMA,
and peripherals. The reference clock for the PLL is taken from either the CLKIN pin or the RTC on-chip
oscillator (as specified through the CLK_SEL pin).
5.5.1
PLL Device-Specific Information
There is a minimum and maximum operating frequency for CLKIN, PLLOUT, and the system clock
(SYSCLK). The system clock generator must be configured not to exceed any of these constraints
documented in this section (certain combinations of external clock inputs, internal dividers, and PLL
multiply ratios are not supported).
Table 5-3. PLLC1 Clock Frequency Ranges
CLOCK SIGNAL NAME
CVDD = 1.05 V
MIN
MAX
CVDD = 1.3 V
MIN
MAX
UNIT
CLKIN (1)
11.2896
12
12.288
11.2896
12
12.288
MHz
RTC Clock
32.768
32.768
KHz
PLLIN
32.768
170
32.768
170
KHz
PLLOUT
60
120
60
120
MHz
SYSCLK
0.032768
60 or 75
0.032768
100 or 120
MHz
PLL_LOCKTIME
(1)
4
4
ms
These CLKIN values are used when the CLK_SEL pin = 1.
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
77
PRODUCT PREVIEW
PARAMETER
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
The PLL has lock time requirements that must be followed. The PLL lock time is the amount of time
needed for the PLL to complete its phase-locking sequence.
5.5.2
Clock PLL Considerations With External Clock Sources
If the CLKIN pin is used to provide the reference clock to the PLL, to minimize the clock jitter a single
clean power supply should power both the C5515 device and the external clock oscillator circuit. The
minimum CLKIN rise and fall times should also be observed. For the input clock timing requirements, see
Section 5.5.3, Clock PLL Electrical Data/Timing (Input and Output Clocks).
Rise/fall times, duty cycles (high/low pulse durations), and the load capacitance of the external clock
source must meet the device requirements in this data manual (see Section 4.3, Electrical Characteristics
Over Recommended Ranges of Supply Voltage and Operating Temperature, and Section 5.5.3, Clock
PLL Electrical Data/Timing (Input and Output Clocks).
5.5.3
Clock PLL Electrical Data/Timing (Input and Output Clocks)
Table 5-4. Timing Requirements for CLKIN (1)
(2)
(see Figure 5-8)
PRODUCT PREVIEW
CVDD = 1.05 V
NO.
MIN
CVDD = 1.3 V
NOM
MAX
MIN
88.577,
83.333,
or
81.380
NOM
MAX
88.577,
83.333,
or
81.380
UNIT
1
tc(CLKIN)
Cycle time, external
clock driven on
CLKIN
2
tw(CLKINH)
Pulse width, CLKIN
high
0.466 * tc(CLKIN)
0.466 * tc(CLKIN)
ns
3
tw(CLKINL)
Pulse width, CLKIN
low
0.466 * tc(CLKIN)
0.466 * tc(CLKIN)
ns
4
tt(CLKIN)
Transition time,
CLKIN
(1)
(2)
4
ns
4
ns
The CLKIN frequency and PLL multiply factor should be chosen such that the resulting clock frequency is within the specific range for
CPU operating frequency.
The reference points for the rise and fall transitions are measured at VIL MAX and VIH MIN.
1
1
4
2
CLKIN
3
4
Figure 5-8. CLKIN Timing
78
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Table 5-5. Switching Characteristics Over Recommended Operating Conditions for CLKOUT (1)
(see Figure 5-9)
NO
.
CVDD = 1.05 V
PARAMETER
(2)
CVDD = 1.3 V
MIN
MAX
MIN
MAX
P
16.67 or
13.33 (3)
P
10 or
8.3 (3)
UNIT
1
tc(CLKOUT)
Cycle time, CLKOUT
2
tw(CLKOUTH)
Pulse duration, CLKOUT high
0.466 *
tc(CLKOUT)
0.466 *
tc(CLKOUT)
ns
3
tw(CLKOUTL)
Pulse duration, CLKOUT low
0.466 *
tc(CLKOUT)
0.466 *
tc(CLKOUT)
ns
(4)
4
tt(CLKOUTR)
Transition time (rise), CLKOUT
5
tt(CLKOUTF)
Transition time (fall), CLKOUT (4)
(1)
(2)
(3)
(4)
ns
5
5
ns
5
5
ns
The reference points for the rise and fall transitions are measured at VOL MAX and VOH MIN.
P = 1/SYSCLK clock frequency in nanoseconds (ns). For example, when SYSCLK frequency is 100 MHz, use P = 10 ns.
Value is maximum device frequency dependant (for more information, see Section 2.6.2 , Device and Development-Support Tool
Nomenclature).
Transition time is measured with the slew rate set to FAST and DVDDIO = 1.65 V. (For more detailed information, see the Section 3.6.6 ,
Output Slew Rate Control Register (OSRCR) [1C16h].).
2
PRODUCT PREVIEW
5
1
CLKOUT
3
4
Figure 5-9. CLKOUT Timing
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
79
TMS320C5515
SPRS645 – JANUARY 2010
5.6
www.ti.com
Direct Memory Access (DMA) Controller
The DMA controller is used to move data among internal memory, external memory, and peripherals
without intervention from the CPU and in the background of CPU operation.
The DSP includes a total of four DMA controllers. Aside from the DSP resources they can access, all four
DMA controllers are identical.
The DMA controller has the following features:
• Operation that is independent of the CPU.
• Four channels, which allow the DMA controller to keep track of the context of four independent block
transfers.
• Event synchronization. DMA transfers in each channel can be made dependent on the occurrence of
selected events.
• An interrupt for each channel. Each channel can send an interrupt to the CPU on completion of the
programmed transfer.
• Ping-Pong mode allows the DMA controller to keep track of double buffering context without CPU
intervention.
• A dedicated clock idle domain. The four device DMA controllers can be put into a low-power state by
independently turning off their input clocks.
PRODUCT PREVIEW
5.6.1
DMA Channel Synchronization Events
The DMA controllers allow activity in their channels to be synchronized to selected events. The DSP
supports 20 separate synchronization events and each channel can be tied to separate sync events
independent of the other channels. Synchronization events are selected by programming the CHnEVT
field in the DMAn channel event source registers (DMAnCESR1 and DMAnCESR2).
80
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
5.7
SPRS645 – JANUARY 2010
Reset
The C5515 has two main types of reset: hardware reset and software reset.
Hardware reset is responsible for initializing all key states of the device. It occurs whenever the RESET
pin is asserted or when the internal power-on-reset (POR) circuit deasserts an internal signal called
POWERGOOD. C5515 device's internal POR is a voltage comparator that monitors the DSP_LDOO pin
voltage and generates the internal POWERGOOD signal when the DSP_LDO is enabled externally by the
DSP_LDO_EN pin. POWERGOOD is asserted when the DSP_LDOO voltage is above a minimum
threshold voltage provided by the bandgap. When the DSP_LDO is disabled (DSP_LDO_EN is high), the
internal voltage comparator becomes inactive, and the POWERGOOD signal logic level is immediately set
high. The RESET pin and the POWERGOOD signal are internally combined with a logical AND gate to
produce an (active low) hardware reset (see Figure 5-10, Power-On Reset Timing Requirements and
Figure 5-11, Reset Timing Requirements).
The C5515 RTC has one additional type of reset, a power-on-reset (POR) for the registers in the RTC
core. This POR monitors the voltage of CVDD_RTC and resets the RTC registers when power is first applied
to the RTC core.
5.7.1
Power-On Reset (POR) Circuits
The C5515 device includes two power-on reset (POR) circuits, one for the RTC (RTC POR) and another
for the rest of the chip (MAIN POR).
5.7.1.1
RTC Power-On Reset (POR)
The RTC POR ensures that the flip-flops in the CVDD_RTC power domain have an initial state upon
powerup. In particular, the RTCNOPWR register is reset by this POR and is used to indicate that the RTC
time registers need to be initialized with the current time and date when power is first applied.
5.7.1.2
Main Power-On Reset (POR)
The C5515 device includes an analog power-on reset (POR) circuit that keeps the DSP in reset until
specific voltages have reached predetermined levels. When the DSP_LDO is enabled externally by the
DSP_LDO_EN pin, the output of the POR circuit, POWERGOOD, is held low until the following conditions
are satisfied:
• LDOI is powered and the bandgap is active for at least approximately 8 ms
• VDD_ANA is powered for at least approximately 4 ms
• DSP_LDOO is above a threshold of approximately 950 mV (see Note:)
Once these conditions are met, the internal POWERGOOD signal is set high. The POWERGOOD signal
is internally combined with the RESET pin signal, via an AND-gate, to produce the DSP subsystem's
global reset. This global reset is the hardware reset for the whole chip, except the RTC. When the global
reset is deasserted (high), the boot sequence starts. For more detailed information on the boot sequence,
see Section 3.4, Boot Sequence.
When the DSP_LDO is disabled (DSP_LDO_EN pin = 1), the voltage monitoring on the DSP_LDOO pin is
de-activated and the POWERGOOD signal is immediately set high. The RESET pin will be the sole
source of hardware reset.
Note: The POR comparator has hysteresis, so the threshold voltage becomes approximately 850 mV after
POWERGOOD signal is set high.
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
81
PRODUCT PREVIEW
There are two types of software reset: the CPU's software reset instruction and the software control of the
peripheral reset signals. For more information on the CPU's software reset instruction, see the
TMS320C55x CPU 3.0 CPU Reference Guide (literature number: SWPU073). In all C5515 documentation,
all references to "reset" refer to hardware reset. Any references to software reset will explicitly state
software reset.
TMS320C5515
SPRS645 – JANUARY 2010
5.7.1.3
www.ti.com
Reset Pin (RESET)
The C5515 can receive an external reset signal on the RESET pin. As specified above in Section 5.7.1.2,
Main Power-On Reset, the RESET pin is combined with the internal POWERGOOD signal, that is
generated by the MAIN POR, via an AND-gate. The output of the AND gate provides the hardware reset
to the chip. The RESET pin may be tied high and the MAIN POR can provide the hardware reset in case
DSP_LDO is enabled (DSP_LDO_EN = 0), but an external hardware reset must be provided via the
RESET pin when the DSP_LDO is disabled (DSP_LDO_EN = 1).
Once the hardware reset is applied, the DSP clock generator is enabled and the DSP starts the boot
sequence. For more information on the boot sequence, see Section 3.4, Boot Sequence.
5.7.2
Pin Behaviors at Reset
PRODUCT PREVIEW
During normal operation, pins are controlled by the respective peripheral selected in the External Bus
Selection Register (EBSR) register. During power-on reset and reset, the behavior of the output pins
changes and is categorized as follows:
• High Group: EM_CS4, EM_CS5, EM_CS2, EM_CS3, EM_DQM0, EM_DQM1, EM_OE, EM_WE,
LCD_RS/SPI_CS3, RSV15, RSV14, XF
• Low
Group:
LCD_EN_RDB/SPI_CLK,
EM_R/W,
MMC0_CLK/I2S0_CLK/GP[0],
MMC1_CLK/I2S1_CLK/GP[6], RSV12
• Z
Group: EM_D[15:0],
EMU[1:0],
SCL,
SDA, LCD_D[0]/SPI_RX, LCD_D[1]/SPI_TX,
LCD_D[10]/I2S2_RX/GP[20]/SPI_RX,
LCD_D[11]/I2S2_DX/GP[27]/SPI_TX,
LCD_D[12]/I2S2_RTS/GP[28]/I2S3_CLK,
LCD_D[13]/I2S2_CTS/GP[29]/I2S3_RS,
LCD_D[14]/I2S2_RXD/GP[30]/I2S3_RX, LCD_D[15]/I2S2_TXD/GP[31]/I2S3_DX, LCD_D[2]/GP[12],
LCD_D[3]/GP[13], LCD_D[4]/GP[14], LCD_D[5]/GP[15], LCD_D[6]/GP[16], LCD_D[7]/GP[17],
LCD_D[8]/I2S2_CLK/GP[18]/SPI_CLK,LCD_D[9]/I2S2_FS/GP[19]/SPI_CS0,
RTC_CLKOUT,
MMC0_CMD/I2S0_FS/GP[1],
MMC0_D0/I2S0_DX/GP[2],
MMC0_D1/I2S0_RX/GP[3],
MMC0_D2/GP[4],
MMC0_D3/GP[5],
MMC1_CMD/I2S1_FS/GP[7],
MMC1_D0/I2S1_DX/GP[8],MMC1_D1/I2S1_RX/GP[9],MMC1_D2/GP[10], MMC1_D3/GP[11], TDO,
WAKEUP
• CLKOUT Group: CLKOUT, LCD_CS1_E1/SPI_CS1
• SYNCH 0→1 Group: LCD_CS0_E0/SPI_CS0, LCD_RW_WRB/SPI_CS2, RSV13
• SYNCH 1→0 Group: RSV10, RSV11
• SYNCH X→1 Group: EM_BA[1:0]
• SYNCH X→0 Group: EM_A[20:0]
82
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
5.7.3
SPRS645 – JANUARY 2010
Reset Electrical Data/Timing
Table 5-6. Timing Requirements for Reset (1) (see Figure 5-10 and Figure 5-10)
CVDD = 1.05 V
NO.
1
(1)
MIN
tw(RSTL)
Pulse duration, RESET low
CVDD = 1.3 V
MAX
3P
MIN
MAX
3P
UNIT
ns
(1)P = 1/SYSCLK clock frequency in ns. For example, if SYSCLK = 12 MHz, use P = 83.3 ns. In IDLE3 mode the system clock
generator is bypassed and the SYSCLK frequency is equal to either CLKIN or the RTC clock frequency depending on CLK_SEL.
POWERGOOD
(Internal)
RESET
PRODUCT PREVIEW
POWERGOOD and RESET
(Internal)
LOW Group
HIGH Group
Z Group
SYNCH X→ 0
Group
SYNCH X→ 1
Group
SYNCH 0→ 1
Group
SYNCH 1→ 0
Group
CLKOUT
64k + 8 clocks if CLK_SEL = 1,
32 + 8 clocks if CLK_SEL = 0
Figure 5-10. Power-On Reset Timing Requirements
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
83
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
POWERGOOD
(Internal)
RESET
POWERGOOD and RESET
(Internal)
LOW Group
HIGH Group
Z Group
SYNCH X → 0
Group
PRODUCT PREVIEW
SYNCH X → 1
Group
SYNCH 0 → 1
Group
SYNCH 1 → 0
Group
CLKOUT
64k + 8 clocks if CLK_SEL = 1,
32 + 8 clocks if CLK_SEL = 0
Figure 5-11. Reset Timing Requirements
84
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
5.8
SPRS645 – JANUARY 2010
Wake-up Events, Interrupts, and XF
The C5515 device has a number of interrupts to service the needs of its peripherals. The interrupts can be
selectively enabled or disabled.
5.8.1
Interrupts Electrical Data/Timing
Table 5-7. Timing Requirements for Interrupts (1) (see Figure 5-12)
CVDD = 1.05 V
CVDD = 1.3 V
NO.
MIN
(1)
UNIT
MAX
1
tw(INTH)
Pulse duration, interrupt high CPU active
2P
ns
2
tw(INTL)
Pulse duration, interrupt low CPU active
2P
ns
P = 1/SYSCLK clock frequency in ns. For example, when running parts at 100 MHz, use P = 10 ns. For example, when running parts at
120 MHz, use P = 8.3 ns.
INTx
2
Figure 5-12. External Interrupt Timings
5.8.2
Wake-Up From IDLE Electrical Data/Timing
Table 5-8. Timing Requirements for Wake-Up From IDLE (see Figure 5-13)
CVDD = 1.05 V
CVDD = 1.3 V
NO.
MIN
1
tw(WKPL)
Pulse duration, WAKEUP or INTx low, SYSCLKDIS = 1
UNIT
MAX
10
ns
Table 5-9. Switching Characteristics Over Recommended Operating Conditions For Wake-Up From
IDLE (1) (2)
(see Figure 5-13)
NO.
CVDD = 1.05 V
CVDD = 1.3 V
PARAMETER
MIN
2
td(WKEVTH-C
KLGEN)
Delay time, wake-up event high to CPU
active
UNIT
MAX
IDLE3 Mode with SYSCLKDIS = 1,
WAKEUP or INTx event, CLK_SEL =
1
P
ns
IDLE3 Mode with SYSCLKDIS = 1,
WAKEUP or INTx event, CLK_SEL =
0
C
ns
3P
ns
IDLE2 Mode; INTx event
(1)
(2)
TYP
P = 1/SYSCLK clock frequency in ns. For example, when running parts at 100 MHz, P = 10 ns.
C = 1/RTCCLK= 30.5 ms. RTCCLK is the clock output of the 32.768-kHz RTC oscillator.
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
85
PRODUCT PREVIEW
1
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
2
CLKOUT
1
WAKEUP
INTx
A.
B.
C.
D.
INT[1:0] can only be used as a wake-up event for IDLE3 and IDLE2 modes.
RTC interrupt (internal signal) can be used as wake-up event for IDLE3 and IDLE2 modes.
Any unmasked interrupt can be used to exit the IDLE2 mode.
CLKOUT reflects either the CPU clock, SAR, USB PHY, or PLL clock dependent on the setting of the CLOCKOUT
Clock Source Register. For this diagram, CLKOUT refers to the CPU clock.
Figure 5-13. Wake-Up From IDLE Timings
5.8.3
XF Electrical Data/Timing
PRODUCT PREVIEW
Table 5-10. Switching Characteristics Over Recommended Operating Conditions For XF (1)
(see Figure 5-14)
NO.
1
(1)
(2)
CVDD = 1.05 V
CVDD = 1.3 V
PARAMETER
td(XF)
(2)
Delay time, CLKOUT high to XF high
MIN
MAX
0
10.2
UNIT
ns
P = 1/SYSCLK clock frequency in ns. For example, when running parts at 100 MHz, P = 10 ns.
C = 1/RTCCLK= 30.5 ms. RTCCLK is the clock output of the 32.768-kHz RTC oscillator.
(A)
CLKOUT
1
XF
A.
CLKOUT reflects either the CPU clock, SAR, USB PHY, or PLL clock dependent on the setting of the CLOCKOUT
Clock Source Register. For this diagram, CLKOUT refers to the CPU clock.
Figure 5-14. XF Timings
86
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
5.9
SPRS645 – JANUARY 2010
External Memory Interface (EMIF)
C5515 supports several memories and external device interfaces, including: NOR Flash, NAND Flash,
SRAM, Non-Mobile SDRAM, and Mobile SDRAM (mSDRAM).
Note: The C5515 can support non-mobile SDRAM under certain circumstances. The C5515 always uses
mobile SDRAM initialization but it is able to support SDRAM memories that ignore the BA0 and BA1 pins
for the 'load mode register' command. During the mobile SDRAM initialization, the device issues the 'load
mode register' initialization command to two different addresses that differ in only the BA0 and BA1
address bits. These registers are the Extended Mode register and the Mode register. The Extended mode
register exists only in mSDRAM and not in non-mSDRAM. If a non-mobile SDRAM memory ignores bits
BA0 and BA1, the second loaded register value overwrites the first, leaving the desired value in the Mode
register and the non-mobile SDRAM will work with device.
The EM_A[20:15] address signals are multiplexed with the GPIO peripheral and controlled by the External
Bus Selection Register (EBSR). For more detail on the pin muxing, see the Section 3.6.1, External Bus
Selection Register (EBSR).
5.9.1
EMIF Asynchronous Memory Support
The EMIF supports asynchronous:
• SRAM memories
• NAND Flash memories
• NOR Flash memories
The EMIF data bus can be configured for both 8- or 16-bit width. The device supports up to 21 address
lines and four external wait/interrupt inputs. Up to four asynchronous chip selects are supported by EMIF
(EM_CS[5:2]).
Each chip select has the following individually programmable attributes:
• Data bus width
• Read cycle timings: setup, hold, strobe
• Write cycle timings: setup, hold, strobe
• Bus turn around time
• Extended Wait Option With Programmable Timeout
• Select Strobe Option
• NAND flash controller supports 1-bit and 4-bit ECC calculation on blocks of 512 bytes
5.9.2
EMIF Mobile Synchronous DRAM Memory Supported
The EMIF supports 16-bit non-mobile and mobile single data rate (SDR) SDRAM in addition to the
asynchronous memories listed in Section 5.9.1, EMIF Asynchronous Memory Support. The supported
SDRAM and mobile SDRAM configurations are:
• One, two, and four bank SDRAM/mSDRAM devices
• Supports devices with eight, nine, ten, and eleven column addresses
• CAS latency of two or three clock cycles
• 16-bit data-bus width
• 3.3/2.8/2.5/1.8 -V LVCMOS interface that is separate from the rest of the chip I/Os.
• One (EMA_CS0) or two (EMA_CS[1:0]) chip selects
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
87
PRODUCT PREVIEW
The EMIF provides an 8-bit or 16-bit data bus, an address bus width up to 21 bits, and 6 chip selects,
along with memory control signals.
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
Additionally, the SDRAM/mSDRAM interface of EMIF supports placing the SDRAM/mSDRAM in
"Self-Refresh" and "Powerdown Modes". Self-Refresh mode allows the SDRAM/mSDRAM to be put into a
low-power state while still retaining memory contents; since the SDRAM/mSDRAM will continue to refresh
itself even without clocks from the DSP. Powerdown mode achieves even lower power, except the DSP
must periodically wake the SDRAM/mSDRAM up and issue refreshes if data retention is required. To
achieve the lowest power consumption, the SDRAM/mSDRAM interface has configurable slew rate on the
EMIF pins.
5.9.3
EMIF Peripheral Register Description(s)
Table 5-11 shows the EMIF registers.
Table 5-11. External Memory Interface (EMIF) Peripheral Registers (1)
HEX ADDRESS
RANGE
PRODUCT PREVIEW
(1)
88
ACRONYM
REGISTER NAME
1000h
REV
1001h
STATUS
Revision Register
Status Register
1004h
AWCCR1
Asynchronous Wait Cycle Configuration Register 1
1005h
AWCCR2
Asynchronous Wait Cycle Configuration Register 2
1008h
SDCR1
SDRAM/mSDRAM Configuration Register 1
1009h
SDCR2
SDRAM/mSDRAM Configuration Register 2
100Ch
SDRCR
SDRAM/mSDRAM Refresh Control Register
1010h
ACS2CR1
Asynchronous CS2 Configuration Register 1
1011h
ACS2CR2
Asynchronous CS2 Configuration Register 2
1014h
ACS3CR1
Asynchronous CS3 Configuration Register 1
1015h
ACS3CR2
Asynchronous CS3 Configuration Register 2
1018h
ACS4CR1
Asynchronous CS4 Configuration Register 1
1019h
ACS4CR2
Asynchronous CS4 Configuration Register 2
101Ch
ACS5CR1
Asynchronous CS5 Configuration Register 1
101Dh
ACS5CR2
Asynchronous CS5 Configuration Register 2
1020h
SDTIMR1
SDRAM/mSDRAM Timing Register 1
1021h
SDTIMR2
SDRAM/mSDRAM Timing Register 2
103Ch
SDSRETR
SDRAM/mSDRAM Self Refresh Exit Timing Register
1040h
EIRR
EMIF Interrupt Raw Register
1044h
EIMR
EMIF Interrupt Mask Register
1048h
EIMSR
EMIF Interrupt Mask Set Register
104Ch
EIMCR
EMIF Interrupt Mask Clear Register
1060h
NANDFCR
NAND Flash Control Register
1064h
NANDFSR1
NAND Flash Status Register 1
1065h
NANDFSR2
NAND Flash Status Register 2
1068h
PGMODECTRL1
Page Mode Control Register 1
1069h
PGMODECTRL2
Page Mode Control Register 2
1070h
NCS2ECC1
NAND Flash CS2 1-Bit ECC Register 1
1071h
NCS2ECC2
NAND Flash CS2 1-Bit ECC Register 2
1074h
NCS3ECC1
NAND Flash CS3 1-Bit ECC Register 1
1075h
NCS3ECC2
NAND Flash CS3 1-Bit ECC Register 2
1078h
NCS4ECC1
NAND Flash CS4 1-Bit ECC Register 1
1079h
NCS4ECC2
NAND Flash CS4 1-Bit ECC Register 2
107Ch
NCS5ECC1
NAND Flash CS5 1-Bit ECC Register 1
Before reading or writing to the EMIF registers, be sure to set the BYTEMODE bits to 00b in the EMIF system control register to enable
word accesses to the EMIF registers.
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Table 5-11. External Memory Interface (EMIF) Peripheral Registers
ACRONYM
REGISTER NAME
107Dh
NCS5ECC2
NAND Flash CS5 1-Bit ECC Register 2
10BCh
NAND4BITECCLOAD
NAND Flash 4-Bit ECC Load Register
10C0h
NAND4BITECC1
NAND Flash 4-Bit ECC Register 1
10C1h
NAND4BITECC2
NAND Flash 4-Bit ECC Register 2
10C4h
NAND4BITECC3
NAND Flash 4-Bit ECC Register 3
10C5h
NAND4BITECC4
NAND Flash 4-Bit ECC Register 4
10C8h
NAND4BITECC5
NAND Flash 4-Bit ECC Register 5
10C9h
NAND4BITECC6
NAND Flash 4-Bit ECC Register 6
10CCh
NAND4BITECC7
NAND Flash 4-Bit ECC Register 7
10CDh
NAND4BITECC8
NAND Flash 4-Bit ECC Register 8
10D0h
NANDERRADD1
NAND Flash 4-Bit ECC Error Address Register 1
10D1h
NANDERRADD2
NAND Flash 4-Bit ECC Error Address Register 2
10D4h
NANDERRADD3
NAND Flash 4-Bit ECC Error Address Register 3
10D5h
NANDERRADD4
NAND Flash 4-Bit ECC Error Address Register 4
10D8h
NANDERRVAL1
NAND Flash 4-Bit ECC Error Value Register 1
10D9h
NANDERRVAL2
NAND Flash 4-Bit ECC Error Value Register 2
10DCh
NANDERRVAL3
NAND Flash 4-Bit ECC Error Value Register 3
10DDh
NANDERRVAL4
NAND Flash 4-Bit ECC Error Value Register 4
Copyright © 2010, Texas Instruments Incorporated
(continued)
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
PRODUCT PREVIEW
HEX ADDRESS
RANGE
(1)
89
TMS320C5515
SPRS645 – JANUARY 2010
5.9.4
www.ti.com
EMIF Electrical Data/Timing CVDD = 1.05 V, DVDDEMIF = 3.3/2.8/2.5/1.8 V
Table 5-12. Timing Requirements for EMIF SDRAM/mSDRAM Interface (see Figure 5-15 and Figure 5-16)
CVDD = 1.05 V
DVDDEMIF = 3.3/2.8/2.5
V
NO.
MIN
19
tsu(DV-CLKH)
Input setup time, read data valid on EM_D[15:0] before
EM_SDCLK rising
20
th(CLKH-DIV)
Input hold time, read data valid on EM_D[15:0] after
EM_SDCLK rising
MAX
CVDD = 1.05 V
DVDDEMIF = 1.8 V UNIT
MIN
MAX
TBD
TBD
ns
1.2
1
ns
Table 5-13. Switching Characteristics Over Recommended Operating Conditions for EMIF
SDRAM/mSDRAM Interface (1) (see Figure 5-15 and Figure 5-16)
NO.
PARAMETER
CVDD = 1.05 V
DVDDEMIF = 3.3/2.8/2.5
V
MIN
MAX
PRODUCT PREVIEW
1
tc(CLK)
Cycle time, EMIF clock EM_SDCLK
2
tw(CLK)
Pulse width, EMIF clock EM_SDCLK high or low
3
td(CLKH-CSV)
Delay time, EM_SDCLK rising to EMA_CS[1:0] valid
TBD
4
toh(CLKH-CSIV)
Output hold time, EM_SDCLK rising to EMA_CS[1:0]
invalid
TBD
5
td(CLKH-DQMV)
Delay time, EM_SDCLK rising to EM_DQM[1:0] valid
TBD
6
toh(CLKH-DQMIV)
Output hold time, EM_SDCLK rising to EM_DQM[1:0]
invalid
TBD
7
td(CLKH-AV)
Delay time, EM_SDCLK rising to EM_A[20:0] and
EM_BA[1:0] valid
TBD
8
toh(CLKH-AIV)
Output hold time, EM_SDCLK rising to EM_A[20:0] and
EM_BA[1:0] invalid
TBD
9
td(CLKH-DV)
Delay time, EM_SDCLK rising to EM_D[15:0] valid
TBD
10
toh(CLKH-DIV)
Output hold time, EM_SDCLK rising to EM_D[15:0]
invalid
TBD
11
td(CLKH-RASV)
Delay time, EM_SDCLK rising to EM_SDRAS valid
TBD
12
toh(CLKH-RASIV)
Output hold time, EM_CLK rising to EM_SDRAS invalid
TBD
13
td(CLKH-CASV)
Delay time, EM_SDCLK rising to EM_SDCAS valid
TBD
14
toh(CLKH-CASIV)
Output hold time, EM_SDCLK rising to EM_SDCAS
invalid
TBD
15
td(CLKH-WEV)
Delay time, EM_SDCLK rising to EM_WE valid
TBD
16
toh(CLKH-WEIV)
Output hold time, EM_SDCLK rising to EM_WE invalid
TBD
17
tdis(CLKH-DHZ)
Delay time, EM_SDCLK rising to EM_D[15:0] Hi-Z
18
tena(CLKH-DLZ)
Output hold time, EM_SDCLK rising to EM_D[15:0]
driving
TBD
21
td(CLKH-CKEV)
Delay time, EM_SDCLK rising to EM_SDCKE valid
TBD
22
toh(CLKH-WEIV)
Output hold time, EM_SDCLK rising to EM_SDCKE
invalid
TBD
(1)
90
E
CVDD = 1.05 V
DVDDEMIF = 1.8 V
MIN
MAX
E
3
ns
3
TBD
TBD
ns
15
TBD
TBD
TBD
TBD
15
TBD
15
TBD
15
TBD
15
TBD
TBD
TBD
TBD
TBD
ns
ns
TBD
TBD
ns
ns
TBD
TBD
ns
ns
TBD
TBD
TBD
ns
ns
TBD
TBD
ns
ns
TBD
TBD
ns
ns
TBD
TBD
ns
ns
TBD
TBD
UNIT
ns
ns
TBD
ns
ns
E = EM_SDCLK period in ns. EM_SDCLK is selected either as SYSCLK or SYSCLK/2. For example, when SYSCLK is selected and set
to 100 MHz, E = 10 ns. When operating the SDRAM/mSDRAM with DVDDEMIF = 3.3 V, 2.8 V, or 2.5 V, the maximum SDRAM/mSDRAM
clock rate is equal to the System clock rate. When operating the SDRAM/mSDRAM at DVDDEMIF = 1.8 V, the maximum
SDRAM/mSDRAM clock rate is half of the System clock rate.
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Table 5-14. Timing Requirements for EMIF Asynchronous Memory (1) (see Figure 5-17, Figure 5-19, and
Figure 5-20)
CVDD = 1.05 V
DVDDEMIF = 3.3/2.8/2.5/1.8 V
NO.
MIN
NOM
UNIT
MAX
READS and WRITES
2
tw(EM_WAIT)
Pulse duration, EM_WAITx assertion and deassertion
2E
ns
14.5
ns
READS
12
tsu(EMDV-EMOEH)
Setup time, EM_D[15:0] valid before EM_OE high
13
th(EMOEH-EMDIV)
Hold time, EM_D[15:0] valid after EM_OE high
14
tsu (EMOEL-EMWAIT)
Setup Time, EM_WAITx asserted before end of Strobe Phase (2)
0
ns
4E + 13
ns
4E + 13
ns
WRITES
26
(1)
E = SYSCLK period in ns, if EMIF is set for "full rate" or E = SYSCLK/2 period in ns, if EMIF is set for "half rate" as defined by bit 14 of
the EMIF Status register (0x1001h). For example, when EMIF is set to full rate and SYSCLK is selected and set to 100 MHz, E = 10 ns.
Setup before end of STROBE phase (if no extended wait states are inserted) by which EM_WAITx must be asserted to add extended
wait states. Figure 5-19 and Figure 5-20 describe EMIF transactions that include extended wait states inserted during the STROBE
phase. However, cycles inserted as part of this extended wait period should not be counted; the 4E requirement is to the start of where
the HOLD phase would begin if there were no extended wait cycles.
PRODUCT PREVIEW
(2)
tsu (EMWEL-EMWAIT) Setup Time, EM_WAITx asserted before end of Strobe Phase (2)
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
91
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
Table 5-15. Switching Characteristics Over Recommended Operating Conditions for EMIF Asynchronous Memory (1)
Figure 5-20) (3)
NO.
(2)
(see Figure 5-18 and
CVDD = 1.05 V
DVDDEMIF = 3.3/2.8/2.5/1.8 V
PARAMETER
MIN
UNIT
NOM
MAX
READS and WRITES
1
td(TURNAROUND)
Turn around time
(TA)*E - 13
(TA)*E
(TA)*E + 13
ns
EMIF read cycle time (EW = 0)
(RS+RST+RH)*E - 13
EMIF read cycle time (EW = 1)
(RS+RST+RH+(EWC*16))*E 13
(RS+RST+RH)*E
(RS+RST+RH)*E + 13
ns
(RS+RST+RH+(EWC*16))*E
(RS+RST+RH+(EWC*16))*E
+139
ns
Output setup time, EM_CS[5:2] low to EM_OE low (SS = 0)
Output setup time, EM_CS[5:2] low to EM_OE low (SS = 1)
(RS)*E-13
(RS)*E
(RS)*E+13
ns
-13
0
+13
ns
Output hold time, EM_OE high to EM_CS[5:2] high (SS = 0)
(RH)*E - 13
(RH)*E
(RH)*E + 13
ns
Output hold time, EM_OE high to EM_CS[5:2] high (SS = 1)
-13
0
+13
ns
READS
PRODUCT PREVIEW
3
tc(EMRCYCLE)
4
tsu(EMCEL-EMOEL)
5
th(EMOEH-EMCEH)
6
tsu(EMBAV-EMOEL)
Output setup time, EM_BA[1:0] valid to EM_OE low
(RS)*E-13
(RS)*E
(RS)*E+13
ns
7
th(EMOEH-EMBAIV)
Output hold time, EM_OE high to EM_BA[1:0] invalid
(RH)*E-13
(RH)*E
(RH)*E+13
ns
8
tsu(EMBAV-EMOEL)
Output setup time, EM_A[20:0] valid to EM_OE low
(RS)*E-13
(RS)*E
(RS)*E+13
ns
9
th(EMOEH-EMAIV)
Output hold time, EM_OE high to EM_A[20:0] invalid
(RH)*E-13
(RH)*E
(RH)*E+13
ns
EM_OE active low width (EW = 0)
(RST)*E-13
(RST)*E
(RST)*E+13
ns
EM_OE active low width (EW = 1)
(RST+(EWC*16))*E-13
(RST+(EWC*16))*E
(RST+(EWC*16))*E+13
ns
4E-13
4E
4E+13
ns
EMIF write cycle time (EW = 0)
(WS+WST+WH)*E-13
(WS+WST+WH)*E
(WS+WST+WH)*E+13
ns
EMIF write cycle time (EW = 1)
(WS+WST+WH+(EWC*16))*E 13
(WS+WST+WH+(EWC*16))*E
(WS+WST+WH+(EWC*16))*E +
13
ns
Output setup time, EM_CS[5:2] low to EM_WE low (SS = 0)
(WS)*E - 13
(WS)*E
(WS)*E + 13
ns
Output setup time, EM_CS[5:2] low to EM_WE low (SS = 1)
-13
0
+13
ns
Output hold time, EM_WE high to EM_CS[5:2] high (SS = 0)
(WH)*E-13
(WH)*E
(WH)*E+13
ns
Output hold time, EM_WE high to EM_CS[5:2] high (SS = 1)
-13
0
+13
ns
10
tw(EMOEL)
11
td(EMWAITH-EMOEH)
Delay time from EM_WAITx deasserted to EM_OE high
WRITES
15
tc(EMWCYCLE)
16
tsu(EMCSL-EMWEL)
17
th(EMWEH-EMCSH)
18
tsu(EMBAV-EMWEL)
Output setup time, EM_BA[1:0] valid to EM_WE low
(WS)*E-13
(WS)*E
(WS)*E+13
ns
19
th(EMWEH-EMBAIV)
Output hold time, EM_WE high to EM_BA[1:0] invalid
(WH)*E-13
(WH)*E
(WH)*E+13
ns
20
tsu(EMAV-EMWEL)
Output setup time, EM_A[20:0] valid to EM_WE low
(WS)*E-13
(WS)*E
(WS)*E+13
ns
21
th(EMWEH-EMAIV)
Output hold time, EM_WE high to EM_A[20:0] invalid
(WH)*E-13
(WH)*E
(WH)*E+13
ns
(1)
(2)
(3)
92
TA = Turn around, RS = Read setup, RST = Read strobe, RH = Read hold, WS = Write setup, WST = Write strobe, WH = Write hold, MEWC = Maximum external wait cycles. These
parameters are programmed via the Asynchronous Configuration and Asynchronous Wait Cycle Configuration Registers.
E = SYSCLK period in ns, if EMIF is set for "full rate" or E = SYSCLK/2 period in ns, if EMIF is set for "half rate" as defined by bit 14 of the EMIF Status register (0x1001h). For example,
when EMIF is set to full rate and SYSCLK is selected and set to 100 MHz, E = 10 ns.
EWC = external wait cycles determined by EM_WAITx input signal. EWC supports the following range of values EWC[256-1]. Note that the maximum wait time before timeout is specified
by bit field MEWC in the Asynchronous Wait Cycle Configuration Register.
Peripheral Information and Electrical Specifications
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Table 5-15. Switching Characteristics Over Recommended Operating Conditions for EMIF Asynchronous Memory
Figure 5-20 ) (3) (continued)
CVDD = 1.05 V
DVDDEMIF = 3.3/2.8/2.5/1.8 V
PARAMETER
MIN
NOM
UNIT
MAX
EM_WE active low width (EW = 0)
(WST)*E-13
(WST)*E
(WST)*E+13
ns
EM_WE active low width (EW = 1)
(WST+(EWC*16))*E-13
(WST+(EWC*16))*E
(WST+(EWC*16))*E+13
ns
3E-13
4E
4E+13
ns
Output setup time, EM_D[15:0] valid to EM_WE low
(WS)*E-13
(WS)*E
(WS)*E+13
ns
Output hold time, EM_WE high to EM_D[15:0] invalid
(WH)*E-13
(WH)*E
(WH)*E+13
ns
22
tw(EMWEL)
23
td(EMWAITH-EMWEH)
Delay time from EM_WAITx deasserted to EM_WE high
24
tsu(EMDV-EMWEL)
25
th(EMWEH-EMDIV)
5.9.5
(see Figure 5-18 and
PRODUCT PREVIEW
NO.
(1) (2)
EMIF Electrical Data/Timing CVDD = 1.3 V, DVDDEMIF = 3.3/2.8/2.5/1.8 V
Peripheral Information and Electrical Specifications
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
93
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
Table 5-16. Timing Requirements for EMIF SDRAM/mSDRAM Interface (see Figure 5-15 and Figure 5-16)
CVDD = 1.3 V
DVDDEMIF = 3.3/2.8/2.5
V
NO.
MIN
19
tsu(DV-CLKH)
Input setup time, read data valid on EM_D[15:0] before
EM_SDCLK rising
20
th(CLKH-DIV)
Input hold time, read data valid on EM_D[15:0] after
EM_SDCLK rising
MAX
CVDD = 1.3 V
DVDDEMIF = 1.8 V UNI
T
MIN
MAX
TBD
TBD
ns
1.1
1
ns
Table 5-17. Switching Characteristics Over Recommended Operating Conditions for EMIF
SDRAM/mSDRAM Interface (1) (see Figure 5-15 and Figure 5-16)
NO.
PARAMETER
CVDD = 1.3 V
DVDDEMIF = 3.3/2.8/2.5
V
MIN
MAX
CVDD = 1.3 V
DVDDEMIF = 1.8 V
MIN
UNIT
MAX
PRODUCT PREVIEW
1
tc(CLK)
Cycle time, EMIF clock EM_SDCLK
E
E
ns
2
tw(CLK)
Pulse width, EMIF clock EM_SDCLK high or low
3
3
ns
3
td(CLKH-CSV)
Delay time, EM_SDCLK rising to EMA_CS[1:0] valid
TBD
4
toh(CLKH-CSIV)
Output hold time, EM_SDCLK rising to EMA_CS[1:0]
invalid
TBD
5
td(CLKH-DQMV)
Delay time, EM_SDCLK rising to EM_DQM[1:0] valid
TBD
6
toh(CLKH-DQMIV)
Output hold time, EM_SDCLK rising to EM_DQM[1:0]
invalid
TBD
7
td(CLKH-AV)
Delay time, EM_SDCLK rising to EM_A[20:0] and
EM_BA[1:0] valid
TBD
8
toh(CLKH-AIV)
Output hold time, EM_SDCLK rising to EM_A[20:0] and
EM_BA[1:0] invalid
TBD
9
td(CLKH-DV)
Delay time, EM_SDCLK rising to EM_D[15:0] valid
TBD
10
toh(CLKH-DIV)
Output hold time, EM_SDCLK rising to EM_D[15:0]
invalid
TBD
11
td(CLKH-RASV)
Delay time, EM_SDCLK rising to EM_SDRAS valid
TBD
12
toh(CLKH-RASIV)
Output hold time, EM_CLK rising to EM_SDRAS invalid
TBD
13
td(CLKH-CASV)
Delay time, EM_SDCLK rising to EM_SDCAS valid
TBD
14
toh(CLKH-CASIV)
Output hold time, EM_SDCLK rising to EM_SDCAS
invalid
TBD
15
td(CLKH-WEV)
Delay time, EM_SDCLK rising to EM_WE valid
TBD
16
toh(CLKH-WEIV)
Output hold time, EM_SDCLK rising to EM_WE invalid
TBD
17
tdis(CLKH-DHZ)
Delay time, EM_SDCLK rising to EM_D[15:0] Hi-Z
18
tena(CLKH-DLZ)
Output hold time, EM_SDCLK rising to EM_D[15:0]
driving
TBD
21
td(CLKH-CKEV)
Delay time, EM_SDCLK rising to EM_SDCKE valid
TBD
toh(CLKH-WEIV)
Output hold time, EM_SDCLK rising to EM_SDCKE
invalid
TBD
22
(1)
94
TBD
TBD
TBD
TBD
TBD
TBD
ns
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
ns
ns
TBD
TBD
TBD
ns
ns
TBD
TBD
ns
ns
TBD
TBD
TBD
ns
ns
TBD
TBD
ns
ns
TBD
TBD
ns
ns
TBD
TBD
ns
ns
ns
TBD
ns
ns
E = EM_SDCLK period in ns. EM_SDCLK is selected either as SYSCLK or SYSCLK/2. For example, when SYSCLK is selected and set
to 100 MHz, E = 10 ns. When operating the SDRAM/mSDRAM with DVDDEMIF = 3.3 V, 2.8 V, or 2.5 V, the maximum SDRAM/mSDRAM
clock rate is equal to the System clock rate. When operating the SDRAM/mSDRAM at DVDDEMIF = 1.8 V, the maximum
SDRAM/mSDRAM clock rate is half of the System clock rate.
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Table 5-18. Timing Requirements for EMIF Asynchronous Memory (1) (see Figure 5-17, Figure 5-19, and
Figure 5-20)
CVDD = 1.3 V
DVDDEMIF = 3.3/2.8/2.5/1.8 V
NO.
MIN
NOM
UNIT
MAX
READS and WRITES
2
tw(EM_WAIT)
Pulse duration, EM_WAITx assertion and deassertion
2E
ns
11
ns
READS
12
tsu(EMDV-EMOEH)
Setup time, EM_D[15:0] valid before EM_OE high
13
th(EMOEH-EMDIV)
Hold time, EM_D[15:0] valid after EM_OE high
14
tsu (EMOEL-EMWAIT)
Setup Time, EM_WAITx asserted before end of Strobe Phase (2)
0
ns
4E + 7.5
ns
4E + 7.5
ns
WRITES
26
(1)
E = SYSCLK period in ns, if EMIF is set for "full rate" or E = SYSCLK/2 period in ns, if EMIF is set for "half rate" as defined by bit 14 of
the EMIF Status register (0x1001h). For example, when EMIF is set to full rate and SYSCLK is selected and set to 100/120 MHz, E =
10/8.33 ns, respectively.
Setup before end of STROBE phase (if no extended wait states are inserted) by which EM_WAITx must be asserted to add extended
wait states. Figure 5-19 and Figure 5-20 describe EMIF transactions that include extended wait states inserted during the STROBE
phase. However, cycles inserted as part of this extended wait period should not be counted; the 4E requirement is to the start of where
the HOLD phase would begin if there were no extended wait cycles.
PRODUCT PREVIEW
(2)
tsu (EMWEL-EMWAIT) Setup Time, EM_WAITx asserted before end of Strobe Phase (2)
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
95
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
Table 5-19. Switching Characteristics Over Recommended Operating Conditions for EMIF Asynchronous Memory (1)
Figure 5-19, and Figure 5-20)
NO.
(2) (3)
(see Figure 5-17,
CVDD = 1.3 V
DVDDEMIF = 3.3/2.8/2.5/1.8 V
PARAMETER
MIN
UNIT
NOM
MAX
READS and WRITES
1
td(TURNAROUND)
Turn around time
(TA)*E - 7.5
(TA)*E
(TA)*E + 7.5
ns
EMIF read cycle time (EW = 0)
(RS+RST+RH)*E - 7.5
EMIF read cycle time (EW = 1)
(RS+RST+RH+(EWC*16))*E 7.5
(RS+RST+RH)*E
(RS+RST+RH)*E + 7.5
ns
(RS+RST+RH+(EWC*16))*E
(RS+RST+RH+(EWC*16))*E +
7.5
ns
Output setup time, EM_CS[5:2] low to EM_OE low (SS = 0)
Output setup time, EM_CS[5:2] low to EM_OE low (SS = 1)
(RS)*E - 7.5
(RS)*E
(RS)*E + 7.5
ns
-7.5
0
+7.5
ns
Output hold time, EM_OE high to EM_CS[5:2] high (SS = 0)
(RH)*E - 7.5
(RH)*E
(RH)*E + 7.5
ns
Output hold time, EM_OE high to EM_CE[5:2] high (SS = 1)
-7.5
0
+7.5
ns
READS
PRODUCT PREVIEW
3
tc(EMRCYCLE)
4
tsu(EMCSL-EMOEL)
5
th(EMOEH-EMCSH)
6
tsu(EMBAV-EMOEL)
Output setup time, EM_BA[1:0] valid to EM_OE low
(RS)*E - 7.5
(RS)*E
(RS)*E + 7.5
ns
7
th(EMOEH-EMBAIV)
Output hold time, EM_OE high to EM_BA[1:0] invalid
(RH)*E - 7.5
(RH)*E
(RH)*E + 7.5
ns
8
tsu(EMAV-EMOEL)
Output setup time, EM_A[20:0] valid to EM_OE low
(RS)*E - 7.5
(RS)*E
(RS)*E + 7.5
ns
9
th(EMOEH-EMAIV)
Output hold time, EM_OE high to EM_A[20:0] invalid
(RH)*E - 7.5
(RH)*E
(RH)*E + 7.5
ns
EM_OE active low width (EW = 0)
(RST)*E - 7.5
(RST)*E
(RST)*E + 7.5
ns
EM_OE active low width (EW = 1)
(RST+(EWC*16))*E - 7.5
(RST+(EWC*16))*E
(RST+(EWC*16))*E + 7.5
ns
4E - 7.5
4E
4E + 7.5
ns
EMIF write cycle time (EW = 0)
(WS+WST+WH)*E - 7.5
(WS+WST+WH)*E
(WS+WST+WH)*E + 7.5
ns
EMIF write cycle time (EW = 1)
(WS+WST+WH+(EWC*16))*E 7.5
(WS+WST+WH+(EWC*16))*E
(WS+WST+WH+(EWC*16))*E +
7.5
ns
Output setup time, EM_CS[5:2] low to EM_WE low (SS = 0)
(WS)*E - 7.5
(WS)*E
(WS)*E +7. 5
ns
Output setup time, EM_CS[5:2] low to EM_WE low (SS = 1)
-7.5
0
+7.5
ns
Output hold time, EM_WE high to EM_CS[5:2] high (SS = 0)
(WH)*E - 7.5
(WH)*E
(WH)*E + 7.5
ns
Output hold time, EM_WE high to EM_CS[5:2] high (SS = 1)
-7.5
0
+7.5
ns
10
tw(EMOEL)
11
td(EMWAITH-EMOEH)
Delay time from EM_WAITx deasserted to EM_OE high
WRITES
15
tc(EMWCYCLE)
16
tsu(EMCSL-EMWEL)
17
th(EMWEH-EMCSH)
18
tsu(EMBAV-EMWEL)
Output setup time, EM_BA[1:0] valid to EM_WE low
(WS)*E - 7.5
(WS)*E
(WS)*E + 7.5
ns
19
th(EMWEH-EMBAIV)
Output hold time, EM_WE high to EM_BA[1:0] invalid
(WH)*E - 7.5
(WH)*E
(WH)*E + 7.5
ns
20
tsu(EMAV-EMWEL)
Output setup time, EM_A[20:0] valid to EM_WE low
(WS)*E - 7.5
(WS)*E
(WS)*E + 7.5
ns
21
th(EMWEH-EMAIV)
Output hold time, EM_WE high to EM_A[20:0] invalid
(WH)*E - 7.5
(WH)*E
(WH)*E + 7.5
ns
(1)
(2)
(3)
96
TA = Turn around, RS = Read setup, RST = Read strobe, RH = Read hold, WS = Write setup, WST = Write strobe, WH = Write hold, MEWC = Maximum external wait cycles. These
parameters are programmed via the Asynchronous Configuration and Asynchronous Wait Cycle Configuration Registers.
E = SYSCLK period in ns, if EMIF is set for "full rate" or E = SYSCLK/2 period in ns, if EMIF is set for "half rate" as defined by bit 14 of the EMIF Status register (0x1001h). For example,
when EMIF is set to full rate and SYSCLK is selected and set to 100/120 MHz, E = 10/8.33, respectively ns.
EWC = external wait cycles determined by EM_WAITx input signal. EWC supports the following range of values EWC[256-1]. Note that the maximum wait time before timeout is specified
by bit field MEWC in the Asynchronous Wait Cycle Configuration Register.
Peripheral Information and Electrical Specifications
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Table 5-19. Switching Characteristics Over Recommended Operating Conditions for EMIF Asynchronous Memory
Figure 5-19 , and Figure 5-20 ) (continued)
(see Figure 5-17 ,
CVDD = 1.3 V
DVDDEMIF = 3.3/2.8/2.5/1.8 V
PARAMETER
MIN
NOM
UNIT
MAX
EM_WE active low width (EW = 0)
(WST)*E - 7.5
(WST)*E
(WST)*E + 7.5
ns
EM_WE active low width (EW = 1)
(WST+(EWC*16))*E - 7.5
(WST+(EWC*16))*E
(WST+(EWC*16))*E + 7.5
ns
3E - 7.5
4E
4E + 7.5
ns
Output setup time, EM_D[15:0] valid to EM_WE low
(WS)*E - 7.5
(WS)*E
(WS)*E + 7.5
ns
Output hold time, EM_WE high to EM_D[15:0] invalid
(WH)*E - 7.5
(WH)*E
(WH)*E + 7.5
ns
22
tw(EMWEL)
23
td(EMWAITH-EMWEH)
Delay time from EM_WAITx deasserted to EM_WE high
24
tsu(EMDV-EMWEL)
25
th(EMWEH-EMDIV)
BASIC mSDRAM
WRITE OPERATION
1
2
PRODUCT PREVIEW
NO.
(1) (2) (3)
2
EM_SDCLK
3
4
EM_CS[1:0]
5
6
EM_DQM[1:0]
7
8
7
8
EM_BA[1:0]
EM_A[20:0]
9
10
EM_D[15:0]
11
12
EM_SDRAS
13
EM_SDCAS
15
16
EM_WE
Figure 5-15. EMIF Basic SDRAM/mSDRAM Write Operation
Peripheral Information and Electrical Specifications
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
97
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
BASIC mSDRAM
READ OPERATION
1
2
2
EM_SDCLK
3
4
EM_CS[1:0]
5
6
EM_DQM[1:0]
7
8
7
8
EM_BA[1:0]
PRODUCT PREVIEW
EM_A[20:0]
19
17
20
2 EM_CLK Delay
18
EM_D[15:0]
11
12
EM_SDRAS
13
14
EM_SDCAS
EM_WE
Figure 5-16. EMIF Basic SDRAM/mSDRAM Read Operation
98
Peripheral Information and Electrical Specifications
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
3
1
EM_CS[5:2]
EM_BA[1:0]
EM_A[20:0]
4
8
5
9
6
7
PRODUCT PREVIEW
10
EM_OE
13
12
EM_D[15:0]
EM_WE
Figure 5-17. Asynchronous Memory Read Timing for EMIF
Peripheral Information and Electrical Specifications
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
99
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
15
1
EM_CS[5:2]
EM_BA[1:0]
EM_A[20:0]
16
17
18
19
20
PRODUCT PREVIEW
22
21
EM_WE
25
24
EM_D[15:0]
EM_OE
Figure 5-18. Asynchronous Memory Write Timing for EMIF
100
Peripheral Information and Electrical Specifications
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
EM_CS[5:2]
SETUP
STROBE
Extended Due to EM_WAITx
STROBE HOLD
EM_BA[1:0]
EM_A[20:0]
EM_D[15:0]
14
11
EM_OE
EM_WAITx
Asserted
2
PRODUCT PREVIEW
2
Deasserted
Figure 5-19. EM_WAITx Read Timing Requirements
EM_CS[5:2]
SETUP
STROBE
Extended Due to EM_WAITx
STROBE HOLD
EM_BA[1:0]
EM_A[20:0]
EM_D[15:0]
28
25
EM_WE
2
EM_WAITx
Asserted
2
Deasserted
Figure 5-20. EM_WAITx Write Timing Requirements
Peripheral Information and Electrical Specifications
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
101
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
5.10 Multimedia Card/Secure Digital (MMC/SD)
The C5515 includes two MMC/SD controllers which are compliant with MMC V3.31, Secure Digital Part 1 Physical Layer Specification V2.0, and
Secure Digital Input Output (SDIO) V3.3 specifications. The MMC/SD card controller supports these industry standards and assumes the reader is
familiar with these standards.
Each C5515 MMC/SD Controller has the following features:
• Multimedia Card/Secure Digital (MMC/SD) protocol support
• Programmable clock frequency
• 512 bit Read/Write FIFO to lower system overhead
• Slave DMA transfer capability
PRODUCT PREVIEW
The MMC/SD card controller transfers data between the CPU and DMA controller on one side and MMC/SD card on the other side. The CPU and
DMA controller can read/write the data in the card by accessing the registers in the MMC/SD controller.
The MMC/SD controller on this device, does not support the SPI mode of operation.
5.10.1
MMC/SD Peripheral Register Description(s)
Table 5-20 and Table 5-21 shows the MMC/SD registers. The MMC/SD0 registers start at address 0x3A00 and the MMC/SD1 registers start at
address 0x3B00.
102
Peripheral Information and Electrical Specifications
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Table 5-20. MMC/SD0 Registers
HEX ADDRESS RANGE
ACRONYM
3A00h
MMCCTL
MMC Control Register
REGISTER NAME
3A04h
MMCCLK
MMC Memory Clock Control Register
3A08h
MMCST0
MMC Status Register 0
3A0Ch
MMCST1
MMC Status Register 1
3A10h
MMCIM
3A14h
MMCTOR
MMC Response Time-Out Register
3A18h
MMCTOD
MMC Data Read Time-Out Register
3A1Ch
MMCBLEN
MMC Block Length Register
3A20h
MMCNBLK
MMC Number of Blocks Register
3A24h
MMCNBLC
MMC Number of Blocks Counter Register
3A28h
MMCDRR1
MMC Data Receive 1 Register
3A29h
MMCDRR2
MMC Data Receive 2 Register
3A2Ch
MMCDXR1
MMC Data Transmit 1 Register
3A2Dh
MMCDXR2
MMC Data Transmit 2 Register
3A30h
MMCCMD
MMC Command Register
3A34h
MMCARGHL
MMC Argument Register
3A38h
MMCRSP0
MMC Response Register 0
3A39h
MMCRSP1
MMC Response Register 1
3A3Ch
MMCRSP2
MMC Response Register 2
3A3Dh
MMCRSP3
MMC Response Register 3
3A40h
MMCRSP4
MMC Response Register 4
3A41h
MMCRSP5
MMC Response Register 5
3A44h
MMCRSP6
MMC Response Register 6
3A45h
MMCRSP7
MMC Response Register 7
3A48h
MMCDRSP
MMC Data Response Register
MMC Command Index Register
3A50h
MMCCIDX
3A64h – 3A70h
–
3A74h
MMCFIFOCTL
PRODUCT PREVIEW
MMC Interrupt Mask Register
Reserved
MMC FIFO Control Register
Peripheral Information and Electrical Specifications
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
103
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
Table 5-21. MMC/SD1 Registers
HEX ADDRESS
RANGE
ACRONYM
3B00h
MMCCTL
MMC Control Register
3B04h
MMCCLK
MMC Memory Clock Control Register
3B08h
MMCST0
MMC Status Register 0
3B0Ch
MMCST1
MMC Status Register 1
PRODUCT PREVIEW
104
REGISTER NAME
3B10h
MMCIM
3B14h
MMCTOR
MMC Interrupt Mask Register
MMC Response Time-Out Register
3B18h
MMCTOD
MMC Data Read Time-Out Register
3B1Ch
MMCBLEN
MMC Block Length Register
3B20h
MMCNBLK
MMC Number of Blocks Register
3B24h
MMCNBLC
MMC Number of Blocks Counter Register
3B28h
MMCDRR1
MMC Data Receive 1 Register
3B29h
MMCDRR2
MMC Data Receive 2 Register
3B2Ch
MMCDXR1
MMC Data Transmit 1 Register
3B2Dh
MMCDXR2
MMC Data Transmit 2 Register
3B30h
MMCCMD
MMC Command Register
3B34h
MMCARGHL
MMC Argument Register
3B38h
MMCRSP0
MMC Response Register 0
3B39h
MMCRSP1
MMC Response Register 1
3B3Ch
MMCRSP2
MMC Response Register 2
3B3Dh
MMCRSP3
MMC Response Register 3
3B40h
MMCRSP4
MMC Response Register 4
3B41h
MMCRSP5
MMC Response Register 5
3B44h
MMCRSP6
MMC Response Register 6
3B45h
MMCRSP7
MMC Response Register 7
3B48h
MMCDRSP
MMC Data Response Register
3B50h
MMCCIDX
MMC Command Index Register
3B74h
MMCFIFOCTL
MMC FIFO Control Register
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
5.10.2 MMC/SD Electrical Data/Timing
Table 5-22. Timing Requirements for MMC/SD (see Figure 5-21 and Figure 5-24)
NO.
CVDD = 1.3 V
CVDD = 1.05 V
FAST MODE
STD MODE
MIN
MAX
MIN
UNIT
MAX
1
tsu(CMDV-CLKH)
Setup time, MMCx_CMD data input valid before MMCx_CLK high
3
3
ns
2
th(CLKH-CMDV)
Hold time, MMCx_CMD data input valid after MMCx_CLK high
3
3
ns
3
tsu(DATV-CLKH)
Setup time, MMC_Dx data input valid before MMCx_CLK high
3
3
ns
4
th(CLKH-DATV)
Hold time, MMC_Dx data input valid after MMCx_CLK high
3
3
ns
Table 5-23. Switching Characteristics Over Recommended Operating Conditions for MMC Output (1) (see
Figure 5-21 and Figure 5-24)
PARAMETER
CVDD = 1.3 V
CVDD = 1.05 V
FAST MODE
STD MODE
UNIT
MIN
MAX
MIN
MAX
7
f(CLK)
Operating frequency, MMCx_CLK
0
50 (2)
0
25 (2)
MHz
8
f(CLK_ID)
Identfication mode frequency, MMCx_CLK
0
400
0
400
kHz
9
tw(CLKL)
Pulse width, MMCx_CLK low
7
10
10
tw(CLKH)
Pulse width, MMCx_CLK high
7
10
11
tr(CLK)
Rise time, MMCx_CLK
TBD
10
ns
12
tf(CLK)
Fall time, MMCx_CLK
TBD
10
ns
13
td(MDCLKL-CMDIV)
Delay time, MMCx_CLK low to MMC_CMD data output invalid
14
td(MDCLKL-CMDV)
Delay time, MMCx_CLK low to MMC_CMD data output valid
15
td(MDCLKL-DATIV)
Delay time, MMCx_CLK low to MMC_Dx data output invalid
td(MDCLKL-DATV)
Delay time, MMCx_CLK low to MMC_Dx data output valid
16
(1)
(2)
-4
ns
ns
-4
ns
4
5
-4
-4
ns
ns
4
5
ns
For MMC/SD, the parametric values are measured at DVDDIO = 3.3 V.
Use this value or SYS_CLK/2 whichever is smaller.
7
9
10
MMCx_CLK
13
14
VALID
MMCx_CMD
Figure 5-21. MMC/SD Host Command Write Timing
9
10
7
MMCx_CLK
4
4
3
MMCx_Dx
Start
3
D0
D1
Dx
End
Figure 5-22. MMC/SD Card Response Timing
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
105
PRODUCT PREVIEW
NO.
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
9
7
10
MMCx_CLK
1
2
MMCx_CMD
START
XMIT
Valid
Valid
Valid
END
Figure 5-23. MMC/SD Host Write Timing
7
9
10
MMCx_CLK
15
16
MMCx_DAT
VALID
PRODUCT PREVIEW
Figure 5-24. MMC/SD Data Write Timing
106
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
5.11 Real-Time Clock (RTC)
The C5515 RTC provides the following features:
• 100-year calendar up to year 2099.
• Counts seconds, minutes, hours, day of the week, date, month, and year with leap year compensation
• Millisecond time correction
• Binary-coded-decimal (BCD) representation of time, calendar, and alarm
• 24-hour clock mode
• Second, minute, hour, day, or week alarm interrupt
• Periodic interrupt: every millisecond, second, minute, hour, or day
• Alarm interrupt: precise time of day
• Single interrupt to the DSP CPU
• 32.768-kHz crystal oscillator with frequency calibration
Control of the RTC is maintained through a set of I/O memory mapped registers (see Table 5-24). Note
that any write to these registers will be synchronized to the RTC 32.768-KHz clock; thus, the CPU must
run at least 3X faster than the RTC. Writes to these registers will not be evident until the next two
32.768-KHz clock cycles later. Furthermore, if the RTC Oscillator is disabled, no RTC register can be
written to.
The RTC has its own power-on-reset (POR) circuit which resets the registers in the RTC core domain
when power is first applied to the CVDD_RTC power pin. The RTC flops are not reset by the device'sRESET
pin nor the digital core's POR (powergood signal) which monitors the DSP_LDOO voltage.
The scratch registers in the RTC can be used to take advantage of this unique reset domain to keep track
of when the DSP boots and whether the RTC time registers have already been initialized to the current
clock time or whether the software needs to go into a routine to prompt the user to set the time/date.
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
107
PRODUCT PREVIEW
The C5515 includes a Real-Time Clock (RTC) with its own separated power supply and isolation circuits.
The separate supply and isolation circuits allow the RTC to run while the rest of the C5515 device (Core
and I/O) is powered off. All RTC registers are preserved (except for RTC Control and RTC Update
Registers) and the counter continues to operate when the device is powered off. The RTC also has the
capability to wakeup the device from idle states via alarms, periodic interrupts, or an external WAKEUP
input. Additionally, the RTC is able to output an alarm or periodic interrupt on the WAKEUP pin to cause
external power management to re-enable power to the DSP Core and I/O.
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
5.11.1 RTC Peripheral Register Description(s)
Table 5-24 shows the RTC registers.
Table 5-24. Real-Time Clock (RTC) Registers
HEX ADDRESS
RANGE
ACRONYM
REGISTER NAME
1900h
RTCINTEN
1901h
RTCUPDATE
RTC Interrupt Enable Register
RTC Update Register
1904h
RTCMIL
Milliseconds Register
1905h
RTCMILA
Milliseconds Alarm Register
1908h
RTCSEC
Seconds Register
1909h
RTCSECA
190Ch
RTCMIN
Seconds Alarm Register
Minutes Register
190Dh
RTCMINA
Minutes Alarm Register
1910h
RTCHOUR
Hours Register
1911h
RTCHOURA
PRODUCT PREVIEW
1914h
RTCDAY
1915h
RTCDAYA
1918h
RTCMONTH
Hours Alarm Register
Days Register
Days Alarm Register
Months Register
1919h
RTCMONTHA
191Ch
RTCYEAR
Months Alarm Register
191Dh
RTCYEARA
1920h
RTCINTFL
1921h
RTCNOPWR
RTC Lost Power Status Register
1924h
RTCINTREG
RTC Interrupt Register
1928h
RTCDRIFT
Years Register
Years Alarm Register
RTC Interrupt Flag Register
RTC Compensation Register
192Ch
RTCOSC
1930h
RTCPMGT
RTC Oscillator Register
RTC Power Management Register
1960h
RTCSCR1
RTC LSW Scratch Register 1
1961h
RTCSCR2
RTC MSW Scratch Register 2
1964h
RTCSCR3
RTC LSW Scratch Register 3
1965h
RTCSCR4
RTC MSW Scratch Register 4
5.11.1.1 RTC Electrical Data/Timing
For more detailed information on RTC electrical timings, specifically WAKEUP, see the Section 5.7.3,
Reset Electrical Data/Timing.
108
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
5.12 Inter-Integrated Circuit (I2C)
The inter-integrated circuit (I2C) module provides an interface between C5515 and other devices
compliant with Philips Semiconductors Inter-IC bus (I2C-bus™) specification version 2.1. External
components attached to this 2-wire serial bus can transmit/receive 2 to 8-bit data to/from the DSP through
the I2C module. The I2C port does not support CBUS compatible devices.
The I2C module clock must be in the range from 6.7 MHz to 13.3 MHz. This is necessary for proper
operation of the I2C module. With the I2C module clock in this range, the noise filters on the SDA and
SCL pins suppress noise that has a duration of 50 ns or shorter. The I2C module clock is derived from the
DSP clock divided by a programmable prescaler.
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
109
PRODUCT PREVIEW
The I2C port supports the following features:
• Compatible with Philips I2C Specification Revision 2.1 (January 2000)
• Data Transfer Rate from 10 kbps to 400 kbps (Philips Fast-Mode Rate)
• Noise Filter to Remove Noise 50 ns or Less
• Seven- and Ten-Bit Device Addressing Modes
• Master (Transmit/Receive) and Slave (Transmit/Receive) Functionality
• One Read DMA Event and One Write DMA Event, which can be used by the DMA Controller
• One Interrupt that can be used by the CPU
• Slew-Rate Limited Open-Drain Output Buffers
TMS320C5515
SPRS645 – JANUARY 2010
5.12.1
www.ti.com
I2C Peripheral Register Description(s)
Table 5-25 shows the Inter-Integrated Circuit (I2C) registers.
Table 5-25. Inter-Integrated Circuit (I2C) Registers
HEX ADDRESS
RANGE
ACRONYM
1A00h
ICOAR
I2C Own Address Register
1A04h
ICIMR
I2C Interrupt Mask Register
1A08h
ICSTR
I2C Interrupt Status Register
1A0Ch
ICCLKL
I2C Clock Low-Time Divider Register
1A10h
ICCLKH
I2C Clock High-Time Divider Register
1A14h
ICCNT
I2C Data Count Register
1A18h
ICDRR
I2C Data Receive Register
1A1Ch
ICSAR
I2C Slave Address Register
1A20h
ICDXR
I2C Data Transmit Register
1A24h
ICMDR
I2C Mode Register
PRODUCT PREVIEW
110
REGISTER NAME
1A28h
ICIVR
I2C Interrupt Vector Register
1A2Ch
ICEMDR
I2C Extended Mode Register
1A30h
ICPSC
I2C Prescaler Register
1A34h
ICPID1
I2C Peripheral Identification Register 1
1A38h
ICPID2
I2C Peripheral Identification Register 2
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
5.12.2
SPRS645 – JANUARY 2010
I2C Electrical Data/Timing
Table 5-26. Timing Requirements for I2C Timings (1) (see Figure 5-25)
CVDD = 1.05 V
CVDD = 1.3 V
STANDARD
MODE
MIN
(2)
(3)
(4)
(5)
(6)
MIN
MAX
1
tc(SCL)
Cycle time, SCL
10
2.5
µs
2
tsu(SCLH-SDAL)
Setup time, SCL high before SDA low (for a repeated START
condition)
4.7
0.6
µs
3
th(SCLL-SDAL)
Hold time, SCL low after SDA low (for a START and a repeated
START condition)
4
0.6
µs
4
tw(SCLL)
Pulse duration, SCL low
4.7
1.3
µs
5
tw(SCLH)
Pulse duration, SCL high
4
0.6
µs
6
tsu(SDAV-SCLH)
Setup time, SDA valid before SCL high
250
100 (2)
(3)
(3)
7
(1)
MAX
UNIT
FAST MODE
th(SDA-SCLL)
Hold time, SDA valid after SCL low
0
8
tw(SDAH)
Pulse duration, SDA high between STOP and START
conditions
4.7
9
tr(SDA)
Rise time, SDA (5)
1000
20 + 0.1Cb
300
ns
10
tr(SCL)
Rise time, SCL (5)
1000
20 + 0.1Cb
300
ns
11
tf(SDA)
Fall time, SDA (5)
300
20 + 0.1Cb
300
ns
12
tf(SCL)
Fall time, SCL (5)
300
20 + 0.1Cb
300
ns
13
tsu(SCLH-SDAH)
Setup time, SCL high before SDA high (for STOP condition)
14
tw(SP)
Pulse duration, spike (must be suppressed)
15
Cb
(6)
Capacitive load for each bus line
0
ns
0.9
(4)
1.3
4
(6)
(6)
(6)
(6)
µs
0.6
0
400
µs
µs
50
ns
400
pF
The I2C pins SDA and SCL do not feature fail-safe I/O buffers. These pins could potentially draw current when the device is powered
down. Also these pins are not 3.6 V-tolerant (their VIH cannot go above DVDDIO + 0.3 V).
A Fast-mode I2C-bus™ device can be used in a Standard-mode I2C-bus system, but the requirement tsu(SDA-SCLH)≥ 250 ns must then be
met. This will automatically be the case if the device does not stretch the LOW period of the SCL signal. If such a device does stretch
the LOW period of the SCL signal, it must output the next data bit to the SDA line tr max + tsu(SDA-SCLH)= 1000 + 250 = 1250 ns
(according to the Standard-mode I2C-Bus Specification) before the SCL line is released.
A device must internally provide a hold time of at least 300 ns for the SDA signal (referred to the VIHmin of the SCL signal) to bridge the
undefined region of the falling edge of SCL.
The maximum th(SDA-SCLL) has only to be met if the device does not stretch the low period [tw(SCLL)] of the SCL signal.
The rise/fall times are measured at 30% and 70% of DVDDIO. The fall time is only slightly influenced by the external bus load (Cb) and
external pullup resistor. However, the rise time (tr) is mainly determined by the bus load capacitance and the value of the pullup resistor.
The pullup resistor must be selected to meet the I2C rise and fall time values specified.
Cb = total capacitance of one bus line in pF. If mixed with HS-mode devices, faster fall-times are allowed.
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
111
PRODUCT PREVIEW
NO.
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
11
9
SDA
6
8
14
4
13
5
10
SCL
1
12
3
2
7
3
Stop
Start
Repeated
Start
Stop
Figure 5-25. I2C Receive Timings
PRODUCT PREVIEW
112
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Table 5-27. Switching Characteristics for I2C Timings (1) (see Figure 5-26)
CVDD = 1.05 V
CVDD = 1.3 V
PARAMETER
STANDARD
MODE
MIN
16
(1)
(2)
MAX
UNIT
FAST MODE
MIN
MAX
tc(SCL)
Cycle time, SCL
10
2.5
µs
17
td(SCLH-SDAL)
Delay time, SCL high to SDA low (for a repeated START
condition)
4.7
0.6
µs
18
td(SDAL-SCLL)
Delay time, SDA low to SCL low (for a START and a repeated
START condition)
4
0.6
µs
19
tw(SCLL)
Pulse duration, SCL low
4.7
1.3
µs
20
tw(SCLH)
Pulse duration, SCL high
4
0.6
µs
21
td(SDAV-SCLH)
Delay time, SDA valid to SCL high
250
100
22
tv(SCLL-SDAV)
Valid time, SDA valid after SCL low
0
0
23
tw(SDAH)
Pulse duration, SDA high between STOP and START
conditions
4.7
1.3
24
tr(SDA)
Rise time, SDA (2)
1000
20 + 0.1Cb
300
ns
25
tr(SCL)
Rise time, SCL (2)
1000
20 + 0.1Cb
300
ns
26
tf(SDA)
Fall time, SDA (2)
300
20 + 0.1Cb
300
ns
27
tf(SCL)
Fall time, SCL (2)
300
20 + 0.1Cb
300
ns
28
td(SCLH-SDAH)
Delay time, SCL high to SDA high (for STOP condition)
29
Cp
Capacitance for each I2C pin
10
pF
4
(1)
(1)
(1)
(1)
ns
0.9
µs
0.6
10
µs
µs
Cb = total capacitance of one bus line in pF. If mixed with HS-mode devices, faster fall-times are allowed.
The rise/fall times are measured at 30% and 70% of DVDDIO. The fall time is only slightly influenced by the external bus load (Cb) and
external pullup resistor. However, the rise time (tr) is mainly determined by the bus load capacitance and the value of the pullup resistor.
The pullup resistor must be selected to meet the I2C rise and fall time values specified.
26
24
SDA
21
23
19
28
20
25
SCL
16
27
18
17
22
18
Stop
Start
Repeated
Start
Stop
Figure 5-26. I2C Transmit Timings
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
113
PRODUCT PREVIEW
NO.
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
5.13 Universal Asynchronous Receiver/Transmitter (UART)
The UART performs serial-to-parallel conversions on data received from an external peripheral device and
parallel-to-serial conversions on data transmitted to an external peripheral device via a serial bus.
PRODUCT PREVIEW
The C5515 has one UART peripheral with the following features:
• Programmable baud rates (frequency pre-scale values from 1 to 65535)
• Fully programmable serial interface characteristics:
– 5, 6, 7, or 8-bit characters
– Even, odd, or no PARITY bit generation and detection
– 1, 1.5, or 2 STOP bit generation
• 16-byte depth transmitter and receiver FIFOs:
– The UART can be operated with or without the FIFOs
– 1, 4, 8, or 14 byte selectable receiver FIFO trigger level for autoflow control and DMA
• DMA signaling capability for both received and transmitted data
• CPU interrupt capability for both received and transmitted data
• False START bit detection
• Line break generation and detection
• Internal diagnostic capabilities:
– Loopback controls for communications link fault isolation
– Break, parity, overrun, and framing error simulation
• Programmable autoflow control using CTS and RTS signals
5.13.1 UART Peripheral Register Description(s)
Table 5-28 shows the UART registers.
Table 5-28. UART Registers
HEX ADDRESS
RANGE
ACRONYM
1B00h
RBR
Receiver Buffer Register (read only)
1B00h
THR
Transmitter Holding Register (write only)
1B02h
IER
Interrupt Enable Register
1B04h
IIR
Interrupt Identification Register (read only)
1B04h
FCR
FIFO Control Register (write only)
1B06h
LCR
Line Control Register
114
REGISTER NAME
1B08h
MCR
Modem Control Register
1B0Ah
LSR
Line Status Register
1B0Ch
MSR
Modem Status Register
1B0Eh
SCR
Scratch Register
1B10h
DLL
Divisor LSB Latch
1B12h
DLH
Divisor MSB Latch
1B18h
PWREMU_MGMT
Power and Emulation Management Register
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
5.13.2 UART Electrical Data/Timing [Receive/Transmit]
Table 5-29. Timing Requirements for UART Receive (1) (2) (see Figure 5-27)
CVDD = 1.05 V
NO.
CVDD = 1.3 V
MIN
MAX
MIN
MAX
UNIT
4
tw(URXDB)
Pulse duration, receive data bit (UART_RXD) [15/30/100 pF]
U - 3.5
U+3
U - 3.5
U+3
ns
5
tw(URXSB)
Pulse duration, receive start bit [15/30/100 pF]
U - 3.5
U+3
U - 3.5
U+3
ns
U = UART baud time = 1/programmed baud rate.
These parametric values are measured at DVDDIO = 3.3 V, 2.75 V, and 2.5 V
Table 5-30. Switching Characteristics Over Recommended Operating Conditions for UART Transmit (1)
(see Figure 5-27)
NO.
1
2
3
(1)
(2)
CVDD = 1.05 V
PARAMETER
MIN
CVDD = 1.3 V
MAX
f(baud)
Maximum programmable bit rate
tw(UTXDB)
Pulse duration, transmit data bit (UART_TXD) [15/30/100
pF]
U - 3.5
U+4
tw(UTXSB)
Pulse duration, transmit start bit [15/30/100 pF]
U - 3.5
U+4
MIN
3.75
MAX
(2)
UNIT
6.25
MHz
U - 3.5
U+4
ns
U - 3.5
U+4
ns
PRODUCT PREVIEW
(1)
(2)
U = UART baud time = 1/programmed baud rate.
These parametric values are measured at DVDDIO = 3.3 V, 2.75 V, and 2.5 V
3
2
UART_TXD
Start
Bit
Data Bits
5
4
UART_RXD
Start
Bit
Data Bits
Figure 5-27. UART Transmit/Receive Timing
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
115
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
5.14 Inter-IC Sound (I2S)
The C5515 I2S peripherals allow serial transfer of full-duplex streaming data, usually audio data, between
the device and an external I2S peripheral device such as an audio codec.
The C5515 supports 4 independent dual-channel I2S peripherals, each with the following features:
• Full-duplex (transmit and receive) dual-channel communication
• Double buffered data registers that allow for continuous data streaming
• I2S/Left-justified and DSP data format with a data delay of 1 or 2 bits
• Data word-lengths of 8, 10, 12, 14, 16, 18, 20, 24, or 32 bits
• Ability to sign-extend received data samples for easy use in signal processing algorithms
• Programmable polarity for both frame synchronization and bit clocks
• Stereo (in I2S/Left-justified or DSP data formats) or mono (in DSP data format) mode
• Detection of over-run, under-run, and frame-sync error conditions
5.14.1
I2S Peripheral Register Description(s)
Table 5-31 through Table 5-34 show the I2S0 through I2S3 registers.
Table 5-31. I2S0 Registers
PRODUCT PREVIEW
HEX ADDRESS
RANGE
ACRONYM
REGISTER NAME
2800h
I2S0SCTRL
I2S0 Serializer Control Register
2804h
I2S0SRATE
I2S0 Sample Rate Generator Register
2808h
I2S0TXLT0
I2S0 Transmit Left Data 0 Register
2809h
I2S0TXLT1
I2S0 Transmit Left Data 1 Register
280Ch
I2S0TXRT0
I2S0 Transmit Right Data 0 Register
280Dh
I2S0TXRT1
I2S0 Transmit Right Data 1 Register
2810h
I2S0INTFL
I2S0 Interrupt Flag Register
2814h
I2S0INTMASK
I2S0 Interrupt Mask Register
2828h
I2S0RXLT0
I2S0 Receive Left Data 0 Register
2829h
I2S0RXLT1
I2S0 Receive Left Data 1 Register
282Ch
I2S0RXRT0
I2S0 Receive Right Data 0 Register
282Dh
I2S0RXRT1
I2S0 Receive Right Data 1 Register
Table 5-32. I2S1 Registers
HEX ADDRESS
RANGE
116
ACRONYM
REGISTER NAME
2900h
I2S1SCTRL
I2S1 Serializer Control Register
2904h
I2S1SRATE
I2S1 Sample Rate Generator Register
2908h
I2S1TXLT0
I2S1 Transmit Left Data 0 Register
2909h
I2S1TXLT1
I2S1 Transmit Left Data 1 Register
290Ch
I2S1TXRT0
I2S1 Transmit Right Data 0 Register
290Dh
I2S1TXRT1
I2S1 Transmit Right Data 1 Register
2910h
I2S1INTFL
I2S1 Interrupt Flag Register
2914h
I2S1INTMASK
I2S1 Interrupt Mask Register
2928h
I2S1RXLT0
I2S1 Receive Left Data 0 Register
2929h
I2S1RXLT1
I2S1 Receive Left Data 1 Register
292Ch
I2S1RXRT0
I2S1 Receive Right Data 0 Register
292Dh
I2S1RXRT1
I2S1 Receive Right Data 1 Register
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Table 5-33. I2S2 Registers
HEX ADDRESS
RANGE
ACRONYM
REGISTER NAME
2A00h
I2S2SCTRL
I2S2 Serializer Control Register
2A04h
I2S2SRATE
I2S2 Sample Rate Generator Register
2A08h
I2S2TXLT0
I2S2 Transmit Left Data 0 Register
2A09h
I2S2TXLT1
I2S2 Transmit Left Data 1 Register
2A0Ch
I2S2TXRT0
I2S2 Transmit Right Data 0 Register
2A0Dh
I2S2TXRT1
I2S2 Transmit Right Data 1 Register
2A10h
I2S2INTFL
I2S2 Interrupt Flag Register
2A14h
I2S2INTMASK
I2S2 Interrupt Mask Register
2A28h
I2S2RXLT0
I2S2 Receive Left Data 0 Register
2A29h
I2S2RXLT1
I2S2 Receive Left Data 1 Register
2A2Ch
I2S2RXRT0
I2S2 Receive Right Data 0 Register
2A2Dh
I2S2RXRT1
I2S2 Receive Right Data 1 Register
HEX ADDRESS
RANGE
ACRONYM
REGISTER NAME
2B00h
I2S3SCTRL
I2S3 Serializer Control Register
2B04h
I2S3SRATE
I2S3 Sample Rate Generator Register
2B08h
I2S3TXLT0
I2S3 Transmit Left Data 0 Register
2B09h
I2S3TXLT1
I2S3 Transmit Left Data 1 Register
2B0Ch
I2S3TXRT0
I2S3 Transmit Right Data 0 Register
2B0Dh
I2S3TXRT1
I2S3 Transmit Right Data 1 Register
2B10h
I2S3INTFL
I2S3 Interrupt Flag Register
2B14h
I2S3INTMASK
I2S3 Interrupt Mask Register
2B28h
I2S3RXLT0
I2S3 Receive Left Data 0 Register
2B29h
I2S3RXLT1
I2S3 Receive Left Data 1 Register
2B2Ch
I2S3RXRT0
I2S3 Receive Right Data 0 Register
2B2Dh
I2S3RXRT1
I2S3 Receive Right Data 1 Register
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
PRODUCT PREVIEW
Table 5-34. I2S3 Registers
117
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
5.14.2 I2S Electrical Data/Timing
Table 5-35. Timing Requirements for I2S [I/O = 3.3 V, 2.8 V, and 2.5 V] (1) (see Figure 5-28)
MASTER
NO.
CVDD = 1.05 V
MIN
MAX
SLAVE
CVDD = 1.3 V
MIN
CVDD = 1.05 V
CVDD = 1.3 V
MIN
MIN
MAX
MAX
UN
IT
MAX
40 or
2P (1)
40 or
2P (1)
40 or 2P (1)
40 or 2P (1)
(2)
ns
1
tc(CLK)
Cycle time, I2S_CLK
2
tw(CLKH)
Pulse duration, I2S_CLK high
20
20
20
20
ns
3
tw(CLKL)
Pulse duration, I2S_CLK low
20
20
20
20
ns
tsu(RXV-CLKH)
Setup time, I2S_RX valid before
I2S CLK high (CLKPOL = 0)
5
5
TBD
TBD
ns
tsu(RXV-CLKL)
Setup time, I2S_RX valid before
I2S_CLK low (CLKPOL = 1)
5
5
TBD
TBD
ns
th(CLKH-RXV)
Hold time, I2S_RX valid after
I2S_CLK high (CLKPOL = 0)
TBD
TBD
TBD
TBD
ns
th(CLKL-RXV)
Hold time, I2S_RX valid after
I2S_CLK low (CLKPOL = 1)
TBD
TBD
TBD
TBD
ns
tsu(FSV-CLKH)
Setup time, I2S_FS valid before
I2S_CLK high (CLKPOL = 0)
–
–
15
15
ns
tsu(FSV-CLKL)
Setup time, I2S_FS valid before
I2S_CLK low (CLKPOL = 1)
–
–
15
15
ns
th(CLKH-FSV)
Hold time, I2S_FS valid after
I2S_CLK high (CLKPOL = 0)
–
–
tw(CLKH) +
TBD (3)
tw(CLKH) +
TBD (3)
ns
th(CLKL-FSV)
Hold time, I2S_FS valid after
I2S_CLK low (CLKPOL = 1)
–
–
tw(CLKL) +
TBD (3)
tw(CLKL) +
TBD (3)
ns
7
8
PRODUCT PREVIEW
9
10
(1)
(2)
(3)
118
(2)
(2)
(2)
P = SYSCLK period in ns. For example, when running parts at 100 MHz, use P = 10 ns.
Use whichever value is greater.
In Slave Mode, I2S_FS is required to be latched on both edges of I2S input clock (I2S_CLK).
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Table 5-36. Timing Requirements for I2S [I/O = 1.8 V] (1) (see Figure 5-28)
NO.
CVDD = 1.05 V
MIN
CVDD = 1.3 V
MIN
50 or
2P (1)
40 or
2P (1)
1
tc(CLK)
Cycle time, I2S_CLK
2
tw(CLKH)
Pulse duration, I2S_CLK high
25
20
3
tw(CLKL)
Pulse duration, I2S_CLK low
25
20
tsu(RXV-CLKH)
Setup time, I2S_RX valid before
I2S CLK high (CLKPOL = 0)
5
tsu(RXV-CLKL)
Setup time, I2S_RX valid before
I2S_CLK low (CLKPOL = 1)
th(CLKH-RXV)
CVDD = 1.05 V
CVDD = 1.3 V
MIN
MIN
MAX
50 or 2P
(1)
MAX
40 or 2P
UN
IT
MAX
(1)
(2)
ns
25
20
ns
25
20
ns
5
TBD
TBD
ns
5
5
TBD
TBD
ns
Hold time, I2S_RX valid after
I2S_CLK high (CLKPOL = 0)
TBD
TBD
TBD
TBD
ns
th(CLKL-RXV)
Hold time, I2S_RX valid after
I2S_CLK low (CLKPOL = 1)
TBD
TBD
TBD
TBD
ns
tsu(FSV-CLKH)
Setup time, I2S_FS valid before
I2S_CLK high (CLKPOL = 0)
–
–
15
15
ns
tsu(FSV-CLKL)
Setup time, I2S_FS valid before
I2S_CLK low (CLKPOL = 1)
–
–
15
15
ns
th(CLKH-FSV)
Hold time, I2S_FS valid after
I2S_CLK high (CLKPOL = 0)
–
–
tw(CLKH) +
TBD (3)
tw(CLKH) +
TBD (3)
ns
th(CLKL-FSV)
Hold time, I2S_FS valid after
I2S_CLK low (CLKPOL = 1)
–
–
tw(CLKL) +
TBD (3)
tw(CLKL) +
TBD (3)
ns
7
8
9
10
(1)
(2)
(3)
MAX
SLAVE
(2)
(2)
(2)
P = SYSCLK period in ns. For example, when running parts at 100 MHz, use P = 10 ns.
Use whichever value is greater.
In Slave Mode, I2S_FS is required to be latched on both edges of I2S input clock (I2S_CLK).
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
119
PRODUCT PREVIEW
MASTER
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
Table 5-37. Switching Characteristics Over Recommended Operating Conditions for I2S Output
[I/O = 3.3 V, 2.8 V, or 2.5 V] (see Figure 5-28)
MASTER
NO
.
PARAMETER
CVDD = 1.05 V
MIN
1
2
3
4
MIN
MAX
CVDD = 1.05 V
MIN
MAX
CVDD = 1.3 V
MIN
UN
IT
MAX
40 or
2P (1) (2)
40 or
2P (1) (2)
40 or
2P (1) (2)
40 or
2P (1) (2)
ns
Pulse duration, I2S_CLK high (CLKPOL = 0)
20
20
20
20
ns
Pulse duration, I2S_CLK low (CLKPOL = 1)
20
20
20
20
ns
tw(CLKL)
Pulse duration, I2S_CLK low (CLKPOL = 0)
20
20
20
20
ns
tw(CLKH)
Pulse duration, I2S_CLK high (CLKPOL = 1)
20
20
20
20
ns
tdmax(CLKL-
Output Delay time, I2S_CLK low to I2S_DX
valid (CLKPOL = 0)
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
ns
Output Delay time, I2S_CLK high to I2S_DX
valid (CLKPOL = 1)
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
ns
Delay time, I2S_CLK low to I2S_FS valid
(CLKPOL = 0)
TBD
TBD
TBD
TBD
–
–
ns
Delay time, I2S_CLK high to I2S_FS valid
(CLKPOL = 1)
TBD
TBD
TBD
TBD
–
–
ns
tc(CLK)
Cycle time, I2S_CLK
tw(CLKH)
tw(CLKL)
DXV)
tdmax(CLKHDXV)
tdmax(CLKL5
MAX
SLAVE
CVDD = 1.3 V
FSV)
tdmax(CLKHFSV)
PRODUCT PREVIEW
(1)
(2)
P = SYSCLK period in ns. For example, when running parts at 100 MHz, use P = 10 ns.
Use whichever value is greater.
120
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Table 5-38. Switching Characteristics Over Recommended Operating Conditions for I2S Output
[I/O = 1.8 V] (see Figure 5-28)
MASTER
NO
.
PARAMETER
CVDD = 1.05 V
MIN
2
3
4
MIN
MAX
MIN
UN
IT
MAX
40 or
2P (1) (2)
50 or
2P (1) (2)
40 or
2P (1) (2)
ns
Pulse duration, I2S_CLK high (CLKPOL = 0)
25
20
25
20
ns
Pulse duration, I2S_CLK low (CLKPOL = 1)
25
20
25
20
ns
tw(CLKL)
Pulse duration, I2S_CLK low (CLKPOL = 0)
25
20
25
20
ns
tw(CLKH)
Pulse duration, I2S_CLK high (CLKPOL = 1)
25
20
25
20
ns
tdmax(CLKL-
Output Delay time, I2S_CLK low to I2S_DX
valid (CLKPOL = 0)
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
ns
Output Delay time, I2S_CLK high to I2S_DX
valid (CLKPOL = 1)
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
ns
Delay time, I2S_CLK low to I2S_FS valid
(CLKPOL = 0)
TBD
TBD
TBD
TBD
–
–
ns
Delay time, I2S_CLK high to I2S_FS valid
(CLKPOL = 1)
TBD
TBD
TBD
TBD
–
–
ns
Cycle time, I2S_CLK
tw(CLKH)
tw(CLKL)
DXV)
tdmax(CLKHtdmax(CLKLFSV)
tdmax(CLKHFSV)
(1)
(2)
MAX
CVDD = 1.3 V
50 or
2P (1) (2)
tc(CLK)
DXV)
5
MIN
CVDD = 1.05 V
P = SYSCLK period in ns. For example, when running parts at 100 MHz, use P = 10 ns.
Use whichever value is greater.
1
2
PRODUCT PREVIEW
1
MAX
SLAVE
CVDD = 1.3 V
3
I2S_CLK
(CLKPOL = 0)
I2S_CLK
(CLKPOL = 1)
5
I2S_FS
(Output, MODE = 1)
8
9
I2S_FS
(Input, MODE = 0)
4
I2S_DX
6
7
I2S_RX
Figure 5-28. I2S Input and Output Timings
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
121
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
5.15 Liquid Crystal Display Controller (LCDC)
The C5515 includes a LCD Interface Display Driver (LIDD) controller.
The LIDD Controller supports the asynchronous LCD interface and has the following features:
• Provides full-timing programmability of control signals and output data
Note: Raster mode is not supported on this device.
The LCD controller is responsible for generating the correct external timing. The DMA engine provides a
constant flow of data from the frame buffer(s) to the external LCD panel via the LIDD controller. In
addition, CPU access is provided to read and write registers.
5.15.1 LCDC Peripheral Register Description(s)
Table 5-39 shows the LCDC peripheral registers.
Table 5-39. LCD Controller Registers
CPU WORD
ADDRESS
ACRONYM
REGISTER DESCRIPTION
PRODUCT PREVIEW
2E00h
LCDREVMIN
LCD Minor Revision Register
2E01h
LCDREVMAJ
LCD Major Revision Register
2E04h
LCDCR
LCD Control Register
2E08h
LCDSR
LCD Status Register
2E0Ch
LCDLIDDCR
2E10h
LCDLIDDCS0CONFIG0
LCD LIDD CS0 Configuration Register 0
2E11h
LCDLIDDCS0CONFIG1
LCD LIDD CS0 Configuration Register 1
2E14h
LCDLIDDCS0ADDR
LCD LIDD CS0 Address Read/Write Register
2E18h
LCDLIDDCS0DATA
LCD LIDD CS0 Data Read/Write Register
2E1Ch
LCDLIDDCS1CONFIG0
LCD LIDD CS1 Configuration Register 0
2E1Dh
LCDLIDDCS1CONFIG1
LCD LIDD CS1 Configuration Register 1
2E20h
LCDLIDDCS1ADDR
LCD LIDD CS1 Address Read/Write Register
LCD LIDD CS1 Data Read/Write Register
LCD LIDD Control Register
2E24h
LCDLIDDCS1DATA
2E28h – 2E3Ah
—
2E40h
LCDDMACR
2E44h
LCDDMAFB0BAR0
LCD DMA Frame Buffer 0 Base Address Register 0
2E45h
LCDDMAFB0BAR1
LCD DMA Frame Buffer 0 Base Address Register 1
2E48h
LCDDMAFB0CAR0
LCD DMA Frame Buffer 0 Ceiling Address Register 0
2E49h
LCDDMAFB0CAR1
LCD DMA Frame Buffer 0 Ceiling Address Register 1
2E4Ch
LCDDMAFB1BAR0
LCD DMA Frame Buffer 1 Base Address Register 0
2E4Dh
LCDDMAFB1BAR1
LCD DMA Frame Buffer 1 Base Address Register 1
2E50h
LCDDMAFB1CAR0
LCD DMA Frame Buffer 1 Ceiling Address Register 0
2E51h
LCDDMAFB1CAR1
LCD DMA Frame Buffer 1 Ceiling Address Register 1
122
Reserved
LCD DMA Control Register
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
5.15.2 LCDC Electrical Data/Timing
Table 5-40. Timing Requirements for LCD LIDD Mode (1) (see Figure 5-29 through Figure 5-36)
CVDD = 1.05 V
NO
MIN
CVDD = 1.3 V
MAX
MIN
MAX
UNIT
16
tsu(LCD_D-CLK)
Setup time, LCD_D[15:0] valid
before LCD_CLK rising edge
27
42
ns
17
th(CLK-LCD_D)
Hold time, LCD_D[15:0] valid after
LCD_CLK rising edge
0
0
ns
(1)
Over operating free-air temperature range (unless otherwise noted)
Table 5-41. Switching Characteristics Over Recommended Operating Conditions for LCD LIDD Mode (see
Figure 5-29 through Figure 5-36)
CVDD = 1.05 V
PARAMETER
MIN
4
td(LCD_D_V)
Delay time, LCD_CLK rising edge
to LCD_D[15:0] valid (write)
5
td(LCD_D_I)
Delay time, LCD_CLK rising edge
to LCD_D[15:0] invalid (write)
6
td(LCD_E_A)
Delay time, LCD_CLK rising edge
to LCD_CSx_Ex low
7
td(LCD_E_I)
Delay time, LCD_CLKrising edge
to LCD_CSx_Ex high
8
td(LCD_A_A)
Delay time, LCD_CLKrising edge
to LCD_RS low
9
td(LCD_A_I)
Delay time, LCD_CLK rising edge
to LCD_RS high
10
td(LCD_W_A)
Delay time, LCD_CLK rising edge
to LCD_RW_WRB low
11
td(LCD_W_I)
Delay time, LCD_CLK rising edge
to LCD_RW_WRB high
12
td(LCD_STRB_A)
Delay time, LCD_CLK rising edge
to LCD_EN_RDB high
13
td(LCD_STRB_I)
Delay time, LCD_CLK rising edge
to LCD_EN_RDB low
14
td(LCD_D_Z)
Delay time, LCD_CLK rising edge
to LCD_D[15:0] in 3-state
15
td(Z_LCD_D)
Delay time, LCD_CLK rising edge
to LCD_D[15:0] valid from 3-state
Copyright © 2010, Texas Instruments Incorporated
CVDD = 1.3 V
MAX
MIN
5
-6
7
-6
5
-6
-6
-6
-6
-6
-6
-6
ns
ns
ns
7
-6
5
ns
ns
7
5
ns
ns
7
5
UNIT
ns
7
5
-6
MAX
ns
ns
7
-6
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
ns
ns
123
PRODUCT PREVIEW
NO
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
W_SU
(0 to 31)
LCD_CLK
[Internal]
CS_DELAY
(0 to 3)
W_STROBE
(1 to 63)
R_SU
(0 to 31)
R_HOLD
(1 to 15)
W_HOLD
(1 to 15)
4
CS_DELAY
(0 to 3)
R_STROBE
(1 to 63)
5
14
17
16
LCD_D[15:0]
15
Write Data
Data[7:0]
Read Status
8
9
LCD_RS
RS
10
11
LCD_RW_WRB
R/W
12
12
13
13
E0
E1
LCD_CSx_Ex
Figure 5-29. Character Display HD44780 Write
W_HOLD
(1–15)
PRODUCT PREVIEW
R_SU
(0–31)
R_STROBE
R_HOLD
CS_DELAY
(1–63)
(1–5)
(0-3)
(0–31)
W_SU
17
15
4
W_STROBE
CS_DELAY
(1–63)
(0 - 3)
LCD_CLK
[Internal]
14
16
LCD_D[7:0]
5
Data[7:0]
Write Instruction
Read
Data
8
9
RS
LCD_RS
10
11
LCD_RW_WRB
R/W
12
12
13
LCD_CSx_Ex
13
E0
E1
Figure 5-30. Character Display HD44780 Read
124
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
W_HOLD
(1-15)
W_HOLD
(1-15)
W_SU
W_STROBE
(0-31)
(1-63)
CS_DELAY
W_SU
(0-3)
(0-31)
W_STROBE
CS_DELAY
(0-3)
(1-63)
LCD_CLK
[Internal]
4
LCD_D[15:0]
5
4
Write Address
Write Data
7
6
Data[15:0]
6
7
CS0
CS1
9
8
RS
LCD_RS
10
11
PRODUCT PREVIEW
LCD_CSx_Ex
(async mode)
5
11
10
R/W
LCD_RW_WRB
12
13
12
13
EN
LCD_EN_RDB
Figure 5-31. Micro-Interface Graphic Display 6800 Write
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
125
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
W_HOLD
(1-15)
W_SU
(0-31)
W_STROBE
R_SU
(0-31)
CS_DELAY
(1-63)
R_STROBE
(1-63
(0-3)
R_HOLD
CS_DELAY
(1-15)
(0-3)
17
15
LCD_CLK
[Internal]
5
4
LCD_D[15:0]
14
16
Write Address
Data[15:0]
6
7
Read
Data
6
LCD_CSx_Ex
(Async Mode)
7
CS0
CS1
9
8
LCD_RS
RS
PRODUCT PREVIEW
10
11
LCD_RW_WRB
R/W
12
13
12
13
LCD_EN_RDB
EN
Figure 5-32. Micro-Interface Graphic Display 6800 Read
126
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
R_SU
(0-31)
R_SU
(0-31)
R_STROBE R_HOLD CS_DELAY
(1-63)
(1-15)
(0-3)
16
17
15
R_STROBE R_HOLD CS_DELAY
(1-63)
(1-15)
(0-3)
17
15
LCD_CLK
[Internal]
14
16
14
LCD_D[15:0]
Read
Data
6
7
Read
Status
6
7
CS0
CS1
8
9
LCD_RS
RS
LCD_RW_WRB
R/W
12
13
12
PRODUCT PREVIEW
LCD_CSx_Ex
(Async Mode)
Data[15:0]
13
EN
LCD_EN_RDB
Figure 5-33. Micro-Interface Graphic Display 6800 Status
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
127
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
W_HOLD
(1-15)
W_HOLD
(1-15)
W_SU
W_STROBE
CS_DELAY
W_SU
(0-31)
(1-63)
(0-3)
(0-31)
W_STROBE
CS_DELAY
(1-63)
(0 - 3)
LCD_CLK
[Internal]
4
LCD_D[15:0]
LCD_CSx_Ex
(Async Mode)
5
4
Write Address
5
DATA[15:0]
Write Data
7
6
6
7
CS0
CS1
8
9
LCD_RS
RS
PRODUCT PREVIEW
10
11
10
11
LCD_RW_WRB
WRB
LCD_EN_RDB
RDB
Figure 5-34. Micro-Interface Graphic Display 8080 Write
128
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
W_HOLD
(1-15)
W_SU
(0-31)
W_STROBE
R_SU
(0-31)
CS_DELAY
(1-63)
R_STROBE
(0-3)
R_HOLD
CS_DELAY
(1-63)
(1-15)
(0-3)
16
17
15
LCD_CLK
[Internal]
4
LCD_D[15:0]
14
Data[15:0]
Write Address
6
7
6
Read
Data
7
CS0
CS1
9
8
LCD_RS
RS
10
PRODUCT PREVIEW
LCD_CSx_Ex
(async mode)
5
11
WRB
LCD_RW_WRB
12
13
RDB
LCD_EN_RDB
Figure 5-35. Micro-Interface Graphic Display 8080 Read
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
129
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
R_SU
(0-31)
R_SU
(0-31)
R_STROBE
(1-63)
R_HOLD
(1-15)
CS_DELAY
R_STROBE R_HOLD
(0-3)
(1-63)
(1-15)
16
17
CS_DELAY
(0-3)
LCD_CLK
[Internal]
14
16
17
15
14
15
Data[15:0]
LCD_D[15:0]
Read Data
Read Status
7
6
6
7
LCD_CSx_Ex
CS0
CS1
8
9
PRODUCT PREVIEW
LCD_RS
RS
LCD_RW_WRB
WRB
12
13
12
13
RDB
LCD_PCLK
Figure 5-36. Micro-Interface Graphic Display 8080 Status
130
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
5.15.2.1 10-Bit SAR ADC
The C5515 includes a 10-bit SAR ADC using a switched capacitor architecture which converts an analog
input signal to a digital value at a maximum rate of 62.5-k samples per second (ksps) for use by the DSP.
This SAR module supports six channels that are connected to four general purpose analog pins (GPAIN
[3:0]) which can be used as general purpose outputs.
The C5515 SAR supports the following features:
• Up to 62.5 ksps (2-MHz clock with 32 cycles per conversion)
• Single conversion and continuous back-to-back conversion modes
• Interrupt driven or polling conversion or DMA event generation
• Internal configurable bandgap reference voltages of 1 V or 0.8 V; or external Vref of VDDA_ANA
• One 3.6-V Tolerant analog input (GPAIN0) with internal voltage division for conversion of battery
voltage
• Software controlled power down
• Individually configurable general-purpose digital outputs
5.15.2.1.1 SAR ADC Peripheral Register Description(s)
Table 5-42. SAR Analog Control Registers
CPU WORD
ADDRESS
ACRONYM
REGISTER DESCRIPTION
7012h
SARCTRL
SAR A/D Control Register
7014h
SARDATA
SAR A/D Data Register
7016h
SARCLKCTRL
SAR A/D Clock Control Register
7018h
SARPINCTRL
SAR A/D Reference and Pin Control Register
701Ah
SARGPOCTRL
SAR A/D GPO Control Register
5.15.2.1.2 SAR ADC Electrical Data/Timing
Table 5-43. Switching Characteristics Over Recommended Operating Conditions for ADC Characteristics
NO.
PARAMETER
CVDD = 1.3 V
CVDD = 1.05 V
MIN
TYP
UNIT
MAX
1
tC(SCLC)
Cycle time, ADC internal conversion clock
3
td(CONV)
Delay time, ADC conversion time
4
SDNL
Static differential non-linearity error (DNL measured for 9 bits)
5
SINL
Static integral non-linearity error
6
Zset
Zero-scale offset error
2
LSB
7
Fset
Full-scale offset error
2
LSB
8
Analog input impedance
9
Signal-to-noise ratio
Copyright © 2010, Texas Instruments Incorporated
2
32tC(SCLC)
MHz
ns
±0.6
LSB
±1
LSB
1
MΩ
54
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
dB
131
PRODUCT PREVIEW
Table 5-42 shows the SAR ADC peripheral registers.
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
5.16 Serial Port Interface (SPI)
The C5515 serial port interface (SPI) is a high-speed synchronous serial input/output port that allows a
serial bit stream of programmed length (1 to 32 bits) to be shifted into and out of the device at a
programmed bit-transfer rate. The SPI supports multi-chip operation of up to four SPI slave devices. The
SPI can operate as a master device only, slave mode is not supported.
The SPI is normally used for communication between the DSP and external peripherals. Typical
applications include an interface to external I/O or peripheral expansion via devices such as shift registers,
display drivers, SPI EEPROMs, and analog-to-digital converters.
PRODUCT PREVIEW
The SPI has the following features:
• Programmable divider for serial data clock generation
• Four pin interface (SPI_CLK, SPI_CSn, SPI_RX, and SPI_TX)
• Programmable data length (1 to 32 bits)
• 4 external chip select signals
• Programmable transfer or frame size (1 to 4096 characters)
• Optional interrupt generation on character completion
• Programmable SPI_CSn to SPI_TX delay from 0 to 3 SPI_CLK cycles
• Programmable signal polarities
• Programmable active clock edge
• Internal loopback mode for testing
5.16.1 SPI Peripheral Register Description(s)
Table 5-44 shows the SPI registers.
Table 5-44. SPI Module Registers
132
CPU
WORD
ADDRESS
ACRONYM
3000h
SPICDR
Clock Divider Register
3001h
SPICCR
Clock Control Register
3002h
SPIDCR1
Device Configuration Register 1
3003h
SPIDCR2
Device Configuration Register 2
3004h
SPICMD1
Command Register 1
3005h
SPICMD2
Command Register 2
3006h
SPISTAT1
Status Register 1
3007h
SPISTAT2
Status Register 2
3008h
SPIDAT1
Data Register 1
3009h
SPIDAT2
Data Register 2
REGISTER NAME
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
5.16.2 SPI Electrical Data/Timing
Table 5-45. Timing Requirements for SPI input (see Figure 5-37 through Figure 5-40)
MIN
30
19
ns
Pulse duration, SPI_CLK low
30
19
ns
Setup time, SPI_RX valid before SPI_CLK high, SPI Mode 0
16.5
11
ns
Setup time, SPI_RX valid before SPI_CLK low, SPI Mode 1
16.5
11
ns
Setup time, SPI_RX valid before SPI_CLK high, SPI Mode 2
16.5
11
ns
Setup time, SPI_RX valid before SPI_CLK high, SPI Mode 3
16.5
11
ns
Hold time, SPI_RX vaild after SPI_CLK high, SPI Mode 0
0
0
ns
Hold time, SPI_RX vaild after SPI_CLK low, SPI Mode 1
0
0
ns
Hold time, SPI_RX vaild after SPI_CLK low, SPI Mode 2
0
0
ns
Hold time, SPI_RX vaild after SPI_CLK high, SPI Mode 3
0
0
ns
tw(SCLKH)
7
tw(SCLKL)
(1)
(2)
UNIT
Pulse duration, SPI_CLK high
6
th(SCLK-SRXV)
MAX
ns
Cycle time, SPI_CLK
9
MIN
40 or
4P (1) (2)
tC(SCLK)
tsu(SRXV-SCLK)
MAX
66.4 or
4P (1) (2)
5
8
CVDD = 1.3 V
P = SYSCLK period in ns. For example, when running parts at 100 MHz, use P = 10 ns.
Use whichever value is greater.
Table 5-46. Switching Characteristics Over Recommended Operating Conditions for SPI Outputs
(see Figure 5-37 through Figure 5-40)
NO.
1
2
3
(1)
CVDD = 1.05 V
PARAMETER
td(SCLK-STXV)
CVDD = 1.3 V
UNIT
MIN
MAX
MIN
MAX
Delay time, SPI_CLK low to SPI_TX vaild, SPI
Mode 0
-5
9
-5
5.5
ns
Delay time, SPI_CLK high to SPI_TX vaild, SPI
Mode 1
-5
9
-5
5.5
ns
Delay time, SPI_CLK high to SPI_TX vaild, SPI
Mode 2
-5
9
-5
5.5
ns
Delay time, SPI_CLK low to SPI_TX vaild, SPI
Mode 3
-5
9
-5
5.5
ns
tC - 8 + D (1)
ns
td(SPICS-SCLK)
Delay time, SPI_CS active to SPI_CLK active
toh(SCLKI-SPICSI)
Output hold time, SPI_CS inactive to SPI_CLK
inactive
tC - 8 + D (1)
0.5tC - 2.5
0.5tC - 2.5
ns
D is the programable data delay in ns. Data delay can be programmed to 0, 1, 2, or 3 SPICLK clock cycles.
4
6
5
SPI_CLK
1
SPI_TX
B0
SPI_RX
B1
B0
B1
7
2
Bn-2
Bn-1
Bn-2
Bn-1
8
3
SPI_CS
A.
B.
Character length is programmable between 1 and 32 bits; 8-bit character length shown.
Polarity of SPI_CSn is configurable, active-low polarity is shown.
Figure 5-37. SPI Mode 0 Transfer (CKPn = 0, CKPHn = 0)
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
133
PRODUCT PREVIEW
CVDD = 1.05 V
NO.
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
4
6
5
SPI_CLK
1
B0
SPI_TX
B1
SPI_RX
7
2
B1
Bn-2
Bn-1
B1
Bn-2
Bn-1
8
3
SPI_CS
A.
B.
Character length is programmable between 1 and 32 bits; 8-bit character length shown.
Polarity of SPI_CSn is configurable, active-low polarity is shown.
Figure 5-38. SPI Mode 1 Transfer (CKPn = 0, CKPHn = 1)
4
5
6
SPI_CLK
1
SPI_TX
B0
B1
SPI_RX
B0
B1
Bn-2
Bn-1
Bn-2
7
2
Bn-1
3
8
PRODUCT PREVIEW
SPI_CS
A.
B.
Character length is programmable between 1 and 32 bits; 8-bit character length shown.
Polarity of SPI_CSn is configurable, active-low polarity is shown.
Figure 5-39. SPI Mode 2 Transfer (CKPn = 1, CKPHn = 0)
4
5
6
SPI_CLK
1
B0
SPI_TX
B0
SPI_RX
SPI_CS
A.
B.
2
7
B1
Bn-2
Bn-1
B1
Bn-2
Bn-1
8
3
Character length is programmable between 1 and 32 bits; 8-bit character length shown.
Polarity of SPI_CSn is configurable, active-low polarity is shown.
Figure 5-40. SPI Mode 3 Transfer (CKPn = 1, CKPHn = 1)
134
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
5.17 Universal Serial Bus (USB) 2.0 Controller
The C5515 USB2.0 peripheral supports the following features:
• USB 2.0 peripheral at speeds high-speed (480 Mb/s) and full-speed (12 Mb/s)
• All transfer modes (control, bulk, interrupt, and isochronous asynchronous mode)
• 4 Transmit (TX) and 4 Receive (RX) Endpoints in addition to Control Endpoint 0
• FIFO RAM
– 4K endpoint
– Programmable size
• Integrated USB 2.0 High Speed PHY
• RNDIS mode for accelerating RNDIS type protocols using short packet termination over USB
PRODUCT PREVIEW
The USB2.0 peripheral on this device, does not support:
• Host Mode (Peripheral/Device Modes supported only)
• On-Chip Charge Pump
• On-the-Go (OTG) Mode
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
135
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
5.17.1 USB2.0 Peripheral Register Description(s)
Table 5-47 lists of the USB2.0 peripheral registers.
Table 5-47. Universal Serial Bus (USB) Registers (1)
CPU WORD
ADDRESS
ACRONYM
8000h
REVID1
Revision Identification Register 1
8001h
REVID2
Revision Identification Register 2
8004h
CTRLR
Control Register
REGISTER DESCRIPTION
8008h
STATR
Status Register
800Ch
EMUR
Emulation Register
8010h
MODER1
Mode Register 1
8011h
MODER2
Mode Register 2
PRODUCT PREVIEW
8014h
AUTOREQ
8018h
SRPFIXTIME1
Auto Request Register
SRP Fix Time Register 1
8019h
SRPFIXTIME2
SRP Fix Time Register 2
801Ch
TEARDOWN1
Teardown Register 1
801Dh
TEARDOWN2
Teardown Register 2
8020h
INTSRCR1
USB Interrupt Source Register 1
8021h
INTSRCR2
USB Interrupt Source Register 2
8024h
INTSETR1
USB Interrupt Source Set Register 1
8025h
INTSETR2
USB Interrupt Source Set Register 2
8028h
INTCLRR1
USB Interrupt Source Clear Register 1
8029h
INTCLRR2
USB Interrupt Source Clear Register 2
802Ch
INTMSKR1
USB Interrupt Mask Register 1
802Dh
INTMSKR2
USB Interrupt Mask Register 2
8030h
INTMSKSETR1
USB Interrupt Mask Set Register 1
8031h
INTMSKSETR2
USB Interrupt Mask Set Register 2
8034h
INTMSKCLRR1
USB Interrupt Mask Clear Register 1
8035h
INTMSKCLRR2
USB Interrupt Mask Clear Register 2
8038h
INTMASKEDR1
USB Interrupt Source Masked Register 1
8039h
INTMASKEDR2
USB Interrupt Source Masked Register 2
803Ch
EOIR
8040h
INTVECTR1
USB Interrupt Vector Register 1
8041h
INTVECTR2
USB Interrupt Vector Register 2
8050h
GREP1SZR1
Generic RNDIS EP1Size Register 1
8051h
GREP1SZR2
Generic RNDIS EP1Size Register 2
8054h
GREP2SZR1
Generic RNDIS EP2 Size Register 1
8055h
GREP2SZR2
Generic RNDIS EP2 Size Register 2
8058h
GREP3SZR1
Generic RNDIS EP3 Size Register 1
8059h
GREP3SZR2
Generic RNDIS EP3 Size Register 2
805Ch
GREP4SZR1
Generic RNDIS EP4 Size Register 1
805Dh
GREP4SZR2
Generic RNDIS EP4 Size Register 2
8401h
FADDR_POWER
8402h
INTRTX
Interrupt Register for Endpoint 0 plus Transmit Endpoints 1 to 4
8405h
INTRRX
Interrupt Register for Receive Endpoints 1 to 4
8406h
INTRTXE
Interrupt enable register for INTRTX
USB End of Interrupt Register
Common USB Registers
(1)
136
Function Address Register, Power Management Register
Before reading or writing to the USB registers, be sure to set the BYTEMODE bits to "00b" in the USB system control register to enable
word accesses to the USB registers .
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Table 5-47. Universal Serial Bus (USB) Registers
CPU WORD
ADDRESS
ACRONYM
(continued)
REGISTER DESCRIPTION
8409h
INTRRXE
840Ah
INTRUSB_INTRUSBE
840Dh
FRAME
840Eh
(1)
Interrupt Enable Register for INTRRX
Interrupt Register for Common USB Interrupts, Interrupt Enable Register
Frame Number Register
Index Register for Selecting the Endpoint Status and Control Registers, Register to
Enable the USB 2.0 Test Modes
INDEX_TESTMODE
USB Indexed Registers
8412h
Maximum Packet Size for Peripheral/Host Transmit Endpoint. (Index register set to
select Endpoints 1-4)
TXMAXP_INDX
Control Status Register for Endpoint 0 in Peripheral Mode. (Index register set to
select Endpoint 0)
PERI_CSR0_INDX
PERI_TXCSR_INDX
8415h
8416h
8419h
Control Status Register for Peripheral Transmit Endpoint. (Index register set to select
Endpoints 1-4)
Maximum Packet Size for Peripheral/Host Receive Endpoint. (Index register set to
select Endpoints 1-4)
RXMAXP_INDX
PERI_RXCSR_INDX
Control Status Register for Peripheral Receive Endpoint. (Index register set to select
Endpoints 1-4)
COUNT0_INDX
Number of Received Bytes in Endpoint 0 FIFO. (Index register set to select Endpoint
0)
Number of Bytes in Host Receive Endpoint FIFO. (Index register set to select
Endpoints 1- 4)
RXCOUNT_INDX
841Ah
-
Reserved
841Dh
-
Reserved
841Eh
CONFIGDATA_INDC
(Upper byte of 841Eh)
8421h
FIFO0R1
Transmit and Receive FIFO Register 1 for Endpoint 0
8422h
FIFO0R2
Transmit and Receive FIFO Register 2 for Endpoint 0
8425h
FIFO1R1
Transmit and Receive FIFO Register 1 for Endpoint 1
8426h
FIFO1R2
Transmit and Receive FIFO Register 2 for Endpoint 1
8429h
FIFO2R1
Transmit and Receive FIFO Register 1 for Endpoint 2
Returns details of core configuration. (index register set to select Endpoint 0)
USB FIFO Registers
842Ah
FIFO2R2
Transmit and Receive FIFO Register 2 for Endpoint 2
842Dh
FIFO3R1
Transmit and Receive FIFO Register 1 for Endpoint 3
842Eh
FIFO3R2
Transmit and Receive FIFO Register 2 for Endpoint 3
8431h
FIFO4R1
Transmit and Receive FIFO Register 1 for Endpoint 4
8432h
FIFO4R2
Transmit and Receive FIFO Register 2 for Endpoint 4
Dynamic FIFO Control Registers
8461h
8462h
-
Reserved
TXFIFOSZ_RXFIFOSZ
Transmit Endpoint FIFO Size, Receive Endpoint FIFO Size (Index register set to
select Endpoints 1-4)
8465h
TXFIFOADDR
Transmit Endpoint FIFO Address (Index register set to select Endpoints 1-4)
8466h
RXFIFOADDR
Receive Endpoint FIFO Address (Index register set to select Endpoints 1-4)
846Dh
-
Reserved
Control and Status Register for Endpoint 0
8501h
-
8502h
PERI_CSR0
8505h
-
Reserved
8506h
-
Reserved
8509h
COUNT0
850Ah
-
Copyright © 2010, Texas Instruments Incorporated
Reserved
Control Status Register for Peripheral Endpoint 0
Number of Received Bytes in Endpoint 0 FIFO
Reserved
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
137
PRODUCT PREVIEW
8411h
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
Table 5-47. Universal Serial Bus (USB) Registers
CPU WORD
ADDRESS
ACRONYM
(1)
(continued)
REGISTER DESCRIPTION
850Dh
-
850Eh
CONFIGDATA
(Upper byte of 850Eh)
Reserved
8511h
TXMAXP
8512h
PERI_TXCSR
Returns details of core configuration.
Control and Status Register for Endpoint 1
8515h
RXMAXP
8516h
PERI_RXCSR
8519h
RXCOUNT
Maximum Packet Size for Peripheral/Host Transmit Endpoint
Control Status Register for Peripheral Transmit Endpoint (peripheral mode)
Maximum Packet Size for Peripheral/Host Receive Endpoint
Control Status Register for Peripheral Receive Endpoint (peripheral mode)
Number of Bytes in the Receiving Endpoint's FIFO
851Ah
-
Reserved
851Dh
-
Reserved
851Eh
-
Reserved
8521h
TXMAXP
8522h
PERI_TXCSR
8525h
RXMAXP
8526h
PERI_RXCSR
8529h
RXCOUNT
852Ah
-
Reserved
852Dh
-
Reserved
852Eh
-
Control and Status Register for Endpoint 2
Maximum Packet Size for Peripheral/Host Transmit Endpoint
Control Status Register for Peripheral Transmit Endpoint (peripheral mode)
PRODUCT PREVIEW
Maximum Packet Size for Peripheral/Host Receive Endpoint
Control Status Register for Peripheral Receive Endpoint (peripheral mode)
Number of Bytes in Host Receive endpoint FIFO
Reserved
Control and Status Register for Endpoint 3
8531h
TXMAXP
8532h
PERI_TXCSR
8535h
RXMAXP
8536h
PERI_RXCSR
Maximum Packet Size for Peripheral/Host Transmit Endpoint
Control Status Register for Peripheral Transmit Endpoint (peripheral mode)
Maximum Packet Size for Peripheral/Host Receive Endpoint
Control Status Register for Peripheral Receive Endpoint (peripheral mode)
8539h
RXCOUNT
853Ah
-
Number of Bytes in Host Receive endpoint FIFO
Reserved
853Dh
-
Reserved
853Eh
-
Reserved
Control and Status Register for Endpoint 4
8541h
TXMAXP
8542h
PERI_TXCSR
8545h
RXMAXP
8546h
PERI_RXCSR
8549h
RXCOUNT
Maximum Packet Size for Peripheral/Host Transmit Endpoint
Control Status Register for Peripheral Transmit Endpoint (peripheral mode)
Maximum Packet Size for Peripheral/Host Receive Endpoint
Control Status Register for Peripheral Receive Endpoint (peripheral mode)
Number of Bytes in Host Receive endpoint FIFO
854Ah
-
Reserved
854Dh
-
Reserved
854Eh
-
Reserved
9000h
-
Reserved
9001h
-
Reserved
CPPI DMA (CMDA) Registers
138
9004h
TDFDQ
9008h
DMAEMU
CDMA Teardown Free Descriptor Queue Control Register
9800h
TXGCR1[0]
Transmit Channel 0 Global Configuration Register 1
9801h
TXGCR2[0]
Transmit Channel 0 Global Configuration Register 2
9808h
RXGCR1[0]
Receive Channel 0 Global Configuration Register 1
CDMA Emulation Control Register
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Table 5-47. Universal Serial Bus (USB) Registers
ACRONYM
(continued)
REGISTER DESCRIPTION
9809h
RXGCR2[0]
980Ch
RXHPCR1A[0]
Receive Channel 0 Global Configuration Register 2
Receive Channel 0 Host Packet Configuration Register 1 A
980Dh
RXHPCR2A[0]
Receive Channel 0 Host Packet Configuration Register 2 A
9810h
RXHPCR1B[0]
Receive Channel 0 Host Packet Configuration Register 1 B
9811h
RXHPCR2B[0]
Receive Channel 0 Host Packet Configuration Register 2 B
9820h
TXGCR1[1]
Transmit Channel 1 Global Configuration Register 1
9821h
TXGCR2[1]
Transmit Channel 1 Global Configuration Register 2
9828h
RXGCR1[1]
Receive Channel 1 Global Configuration Register 1
9829h
RXGCR2[1]
Receive Channel 1 Global Configuration Register 2
982Ch
RXHPCR1A[1]
Receive Channel 1 Host Packet Configuration Register 1 A
982Dh
RXHPCR2A[1]
Receive Channel 1 Host Packet Configuration Register 2 A
9830h
RXHPCR1B[1]
Receive Channel 1 Host Packet Configuration Register 1 B
9831h
RXHPCR2B[1]
Receive Channel 1 Host Packet Configuration Register 2 B
9840h
TXGCR1[2]
Transmit Channel 2 Global Configuration Register 1
9841h
TXGCR2[2]
Transmit Channel 2 Global Configuration Register 2
9848h
RXGCR1[2]
Receive Channel 2 Global Configuration Register 1
9849h
RXGCR2[2]
Receive Channel 2 Global Configuration Register 2
984Ch
RXHPCR1A[2]
Receive Channel 2 Host Packet Configuration Register 1 A
984Dh
RXHPCR2A[2]
Receive Channel 2 Host Packet Configuration Register 2 A
9850h
RXHPCR1B[2]
Receive Channel 2 Host Packet Configuration Register 1 B
9851h
RXHPCR2B[2]
Receive Channel 2 Host Packet Configuration Register 2 B
9860h
TXGCR1[3]
Transmit Channel 3 Global Configuration Register 1
9861h
TXGCR2[3]
Transmit Channel 3 Global Configuration Register 2
9868h
RXGCR1[3]
Receive Channel 3 Global Configuration Register 1
9869h
RXGCR2[3]
Receive Channel 3 Global Configuration Register 2
986Ch
RXHPCR1A[3]
Receive Channel 3 Host Packet Configuration Register 1 A
986Dh
RXHPCR2A[3]
Receive Channel 3 Host Packet Configuration Register 2 A
9870h
RXHPCR1B[3]
Receive Channel 3 Host Packet Configuration Register 1 B
9871h
RXHPCR2B[3]
Receive Channel 3 Host Packet Configuration Register 2 B
A000h
DMA_SCHED_CTRL1
CDMA Scheduler Control Register 1
A001h
DMA_SCHED_CTRL2
CDMA Scheduler Control Register 1
A800h + 4 × N
ENTRYLSW[N]
A801h + 4 × N
ENTRYMSW[N]
PRODUCT PREVIEW
CPU WORD
ADDRESS
(1)
CDMA Scheduler Table Word N Registers LSW (N = 0 to 63)
CDMA Scheduler Table Word N Registers MSW (N = 0 to 63)
Queue Manager (QMGR) Registers
C000h
-
Reserved
C001h
-
Reserved
C008h
DIVERSION1
Queue Manager Queue Diversion Register 1
C009h
DIVERSION2
Queue Manager Queue Diversion Register 2
C020h
FDBSC0
Queue Manager Free Descriptor/Buffer Starvation Count Register 0
C021h
FDBSC1
Queue Manager Free Descriptor/Buffer Starvation Count Register 1
C024h
FDBSC2
Queue Manager Free Descriptor/Buffer Starvation Count Register 2
C025h
FDBSC3
Queue Manager Free Descriptor/Buffer Starvation Count Register 3
C028h
FDBSC4
Queue Manager Free Descriptor/Buffer Starvation Count Register 4
C029h
FDBSC5
Queue Manager Free Descriptor/Buffer Starvation Count Register 5
C02Ch
FDBSC6
Queue Manager Free Descriptor/Buffer Starvation Count Register 6
C02Dh
FDBSC7
Queue Manager Free Descriptor/Buffer Starvation Count Register 7
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
139
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
Table 5-47. Universal Serial Bus (USB) Registers
(1)
(continued)
PRODUCT PREVIEW
CPU WORD
ADDRESS
ACRONYM
C080h
LRAM0BASE1
Queue Manager Linking RAM Region 0 Base Address Register 1
C081h
LRAM0BASE2
Queue Manager Linking RAM Region 0 Base Address Register 2
C084h
LRAM0SIZE
C085h
-
C088h
LRAM1BASE1
Queue Manager Linking RAM Region 1 Base Address Register 1
C089h
LRAM1BASE2
Queue Manager Linking RAM Region 1 Base Address Register 2
C090h
PEND0
Queue Manager Queue Pending 0
C091h
PEND1
Queue Manager Queue Pending 1
C094h
PEND2
Queue Manager Queue Pending 2
C095h
PEND3
Queue Manager Queue Pending 3
C098h
PEND4
Queue Manager Queue Pending 4
C099h
PEND5
Queue Manager Queue Pending 5
D000h + 16 × R
QMEMRBASE1[R]
Queue Manager Memory Region R Base Address Register 1 (R = 0 to 15)
D001h + 16 × R
QMEMRBASE2[R]
Queue Manager Memory Region R Base Address Register 2 (R = 0 to 15)
D004h + 16 × R
QMEMRCTRL1[R]
Queue Manager Memory Region R Control Register (R = 0 to 15)
D005h + 16 × R
QMEMRCTRL2[R]
Queue Manager Memory Region R Control Register (R = 0 to 15)
E000h + 16 × N
CTRL1A
Queue Manager Queue N Control Register 1A (N = 0 to 63)
E001h + 16 × N
CTRL2A
Queue Manager Queue N Control Register 2A (N = 0 to 63)
E004h + 16 × N
CTRL1B
Queue Manager Queue N Control Register 1B (N = 0 to 63)
E005h + 16 × N
CTRL2B
Queue Manager Queue N Control Register 2B (N = 0 to 63)
E008h + 16 × N
CTRL1C
Queue Manager Queue N Control Register 1C (N = 0 to 63)
E009h + 16 × N
CTRL2C
Queue Manager Queue N Control Register 2C (N = 0 to 63)
E00Ch + 16 × N
CTRL1D
Queue Manager Queue N Control Register 1D (N = 0 to 63)
E00Dh + 16 × N
CTRL2D
Queue Manager Queue N Control Register 2D (N = 0 to 63)
E800h + 16 × N
QSTAT1A
Queue Manager Queue N Status Register 1A (N = 0 to 63)
E801h + 16 × N
QSTAT2A
Queue Manager Queue N Status Register 2A (N = 0 to 63)
E804h + 16 × N
QSTAT1B
Queue Manager Queue N Status Register 1B (N = 0 to 63)
E805h + 16 × N
QSTAT2B
Queue Manager Queue N Status Register 2B (N = 0 to 63)
E808h + 16 × N
QSTAT1C
Queue Manager Queue N Status Register 1C (N = 0 to 63)
E809h + 16 × N
QSTAT1C
Queue Manager Queue N Status Register 2C (N = 0 to 63)
140
REGISTER DESCRIPTION
Queue Manager Linking RAM Region 0 Size Register
Reserved
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
5.17.2 USB2.0 Electrical Data/Timing
Table 5-48. Switching Characteristics Over Recommended Operating Conditions for USB2.0 (see
Figure 5-41)
CVDD = 1.05 V
CVDD = 1.3 V
NO.
1
tr(D)
FULL SPEED
12 Mbps
Rise time, USB_DP and USB_DM signals (2)
(2)
HIGH SPEED
480 Mbps (1)
MIN
MAX
MIN
4
20
0.5
UNIT
MAX
ns
2
tf(D)
Fall time, USB_DP and USB_DM signals
4
20
0.5
3
trfM
Rise/Fall time, matching (3)
90
111
–
–
%
4
VCRS
Output signal cross-over voltage (2)
1.3
2
–
–
V
160
175
–
–
ns
(4)
7
tw(EOPT)
Pulse duration, EOP transmitter
8
tw(EOPR)
Pulse duration, EOP receiver (4)
9
t(DRATE)
Data Rate
10
ZDRV
Driver Output Resistance
40.5
11
ZINP
Receiver Input Impedance
100k
82
ns
–
12
49.5
ns
480
Mb/s
40.5
49.5
Ω
-
-
Ω
PRODUCT PREVIEW
(1)
(2)
(3)
(4)
PARAMETER
For more detailed informaton, see the Universal Serial Bus Specification, Revision 2.0, Chapter 7.
Full Speed and High Speed CL = 50 pF
tRFM = (tr/tf) x 100. [Excluding the first transaction from the Idle state.]
Must accept as valid EOP
USB_DM
VCRS
USB_DP
tper - tjr
90% VOH
10% VOL
tr
tf
Figure 5-41. USB2.0 Integrated Transceiver Interface Timing
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
141
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
5.18 General-Purpose Timers
The C5515 has three 32-bit software programmable Timers. Each timer can be used as a
general- purpose (GP) timer. Timer2 can be configured as either a GP or a Watchdog (WD) or both.
General-purpose timers are typically used to provide interrupts to the CPU to schedule periodic tasks or a
delayed task. A watchdog timer is used to reset the CPU in case it gets into an infinite loop. The GP
timers are 32-bit timers with a 13-bit prescaler that can divide the CPU clock and uses this scaled value as
a reference clock. These timers can be used to generate periodic interrupts. The Watchdog Timer is a
16-bit counter with a 16-bit prescaler used to provide a recovery mechanism for the device in the event of
a fault condition, such as a non-exiting code loop.
PRODUCT PREVIEW
The C5515 Timers support the following:
• 32-bit Programmable Countdown Timer
• 13-bit Prescaler Divider
• Timer Modes:
– 32-bit General-Purpose Timer
– 32-bit Watchdog Timer (Timer2 only)
• Auto Reload Option
• Generates Single Interrupt to CPU (The interrupt is individually latched to determine which timer
triggered the interrupt.)
• Generates Active Low Pulse to the Hardware Reset (Watchdog only)
• Interrupt can be Used for DMA Event
5.18.1 Timers Peripheral Register Description(s)
Table 5-49 through Table 5-52 show the Timer and Watchdog registers.
Table 5-49. Watchdog Timer Registers (Timer2 only)
CPU WORD
ADDRESS
ACRONYM
1880h
WDKCKLK
REGISTER DESCRIPTION
Watchdog Kick Lock Register
1882h
WDKICK
Watchdog Kick Register
1884h
WDSVLR
Watchdog Start Value Lock Register
1886h
WDSVR
Watchdog Start Value Register
Watchdog Enable Lock Register
1888h
WDENLOK
188Ah
WDEN
188Ch
WDPSLR
188Eh
WDPS
Watchdog Enable Register
Watchdog Prescale Lock Register
Watchdog Prescale Register
Table 5-50. General-Purpose Timer 0 Registers
CPU WORD
ADDRESS
ACRONYM
REGISTER DESCRIPTION
1810h
TCR
Timer 0 Control Register
1812h
TIMPRD1
Timer 0 Period Register 1
1813h
TIMPRD2
Timer 0 Period Register 2
1814h
TIMCNT1
Timer 0 Counter Register 1
1815h
TIMCNT2
Timer 0 Counter Register 2
Table 5-51. General-Purpose Timer 1 Registers
142
CPU WORD
ADDRESS
ACRONYM
1850h
TCR
REGISTER DESCRIPTION
Timer 1 Control Register
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Table 5-51. General-Purpose Timer 1 Registers (continued)
CPU WORD
ADDRESS
ACRONYM
1852h
TIMPRD1
Timer 1 Period Register 1
1853h
TIMPRD2
Timer 1 Period Register 2
1854h
TIMCNT1
Timer 1 Counter Register 1
1855h
TIMCNT2
Timer 1 Counter Register 2
REGISTER DESCRIPTION
Table 5-52. General-Purpose Timer 2 Registers
CPU WPRD
ADDRESS
ACRONYM
1890h
TCR
Timer 2 Control Register
1892h
TIMPRD1
Timer 2 Period Register 1
1893h
TIMPRD2
Timer 2 Period Register 2
1894h
TIMCNT1
Timer 2 Counter Register 1
1895h
TIMCNT2
Timer 2 Counter Register 2
PRODUCT PREVIEW
REGISTER DESCRIPTION
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
143
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
5.19 General-Purpose Input/Output
The GPIO peripheral provides general-purpose pins that can be configured as either inputs or outputs.
When configured as an output, you can write to an internal register to control the state driven on the
output pin. When configured as an input, you can detect the state of the input by reading the state of the
internal register. The GPIO can also be used to send interrupts to the CPU.
The C5515 GPIO peripheral supports the following:
• Up to 26 GPIOs plus 1 general-purpose output (XF) and 4 Special-Purpose Outputs for Use With SAR
• The 26 GPIO pins have internal pulldowns (IPDs) which can be individually disabled
• The 26 GPIOs can be configured to generate edge detected interrupts to the CPU on either the rising
or falling edge
C5515 GPIO pin functions are multiplexed with various other signals. For more detailed information on
what signals are multiplexed with the GPIO and how to configure them, see Section 2.5, Terminal
Functions and Section 3, Device Configuration of this document.
PRODUCT PREVIEW
144
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
5.19.1
SPRS645 – JANUARY 2010
General-Purpose Input/Output Peripheral Register Description(s)
The external parallel port interface includes a 16-bit general purpose I/O that can be individually
programmed as input or output with interrupt capability. Control of the general purpose I/O is maintained
through a set of I/O memory-mapped registers shown in Table 5-53.
Table 5-53. GPIO Registers
HEX ADDRESS
RANGE
ACRONYM
1C06h
IODIR1
GPIO Direction Register 1
1C07h
IODIR2
GPIO Direction Register 2
1C08h
IOINDATA1
GPIO Data In Register 1
GPIO Data In Register 2
1C09h
IOINDATA2
1C0Ah
IODATAOUT1
GPIO Data Out Register 1
1C0Bh
IODATAOUT2
GPIO Data Out Register 2
1C0Ch
IOINTEDG1
GPIO Interrupt Edge Trigger Enable Register 1
1C0Dh
IOINTEDG2
GPIO Interrupt Edge Trigger Enable Register 2
1C0Eh
IOINTEN1
GPIO Interrupt Enable Register 1
1C0Fh
IOINTEN2
GPIO Interrupt Enable Register 2
1C10h
IOINTFLG1
GPIO Interrupt Flag Register 1
1C11h
IOINTFLG2
GPIO Interrupt Flag Register 2
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
PRODUCT PREVIEW
REGISTER NAME
145
TMS320C5515
SPRS645 – JANUARY 2010
5.19.2
www.ti.com
GPIO Peripheral Input/Output Electrical Data/Timing
Table 5-54. Timing Requirements for GPIO Inputs (1) (see Figure 5-42)
CVDD = 1.05 V
CVDD = 1.3 V
NO.
MIN
1
tw(ACTIVE)
2
(1)
tw(INACTIVE)
2C (1)
Pulse duration, GPIO input/external interrupt pulse active
Pulse duration, GPIO input/external interrupt pulse inactive
C
UNIT
MAX
(2)
ns
(1) (2)
ns
The pulse width given is sufficient to get latched into the GPIO_IFR register and to generate an interrupt. However, if a user wants to
have the device recognize the GPIO changes through software polling of the GPIO Data In (GPIO_DIN) register, the GPIO duration
must be extended to allow the device enough time to access the GPIO register through the internal bus.
C = SYSCLK period in ns. For example, when running parts at 100 MHz, use C = 10 ns.
(2)
Table 5-55. Switching Characteristics Over Recommended Operating Conditions for GPIO Outputs
(see Figure 5-42)
NO.
CVDD = 1.05 V
CVDD = 1.3 V
PARAMETER
MIN
PRODUCT PREVIEW
(1)
(2)
UNIT
MAX
3
tw(GPOH)
Pulse duration, GP[x] output high
3C (1)
(2)
ns
4
tw(GPOL)
Pulse duration, GP[x] output low
3C (1)
(2)
ns
This parameter value should not be used as a maximum performance specification. Actual performance of back-to-back accesses of the
GPIO is dependent upon internal bus activity.
C = SYSCLK period in ns. For example, when running parts at 100 MHz, use C = 10 ns.
2
GP[x] Input
(With IOINTEDGy = 0)
1
2
GP[x] Input
(With IOINTEDGy = 1)
1
4
3
GP[x] Output
Figure 5-42. GPIO Port Timing
146
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
5.19.3
SPRS645 – JANUARY 2010
GPIO Peripheral Input Latency Electrical Data/Timing
Table 5-56. Timing Requirements for GPIO Input Latency (1)
CVDD = 1.05 V
CVDD = 1.3 V
NO
.
1
tL(GPI)
Latency, GP[x] input
UNIT
MAX
Polling GPIO_DIN register
5
cyc
Polling GPIO_IFR register
7
cyc
Interrupt Detection
8
cyc
The pulse width given is sufficient to generate a CPU interrupt. However, if a user wants to have C5515 recognize the GP[x] input
changes through software polling of the GPIO register, the GP[x] input duration must be extended to allow device enough time to access
the GPIO register through the internal bus.
PRODUCT PREVIEW
(1)
MIN
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
147
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
5.20 IEEE 1149.1 JTAG
The JTAG interface is used for Boundary-Scan testing and emulation of the C5515 device.
TRST should only to be deasserted when it is necessary to use a JTAG controller to debug the device or
exercise the device's boundary scan functionality.
The C5515 includes an internal pulldown (IPD) on the TRST pin to ensure that TRST will always be
asserted upon power up and the device's internal emulation logic will always be properly initialized. It is
also recommended that an external pulldown be added to ensure proper device operation when an
emulation or boundary scan JTAG controller is not connected to the JTAG pins. JTAG controllers from
Texas Instruments actively drive TRST high. However, some third-party JTAG controllers may not drive
TRST high but expect the use of a pullup resistor on TRST. When using this type of JTAG controller,
assert TRST to initialize the device after powerup and externally drive TRST high before attempting any
emulation or boundary scan operations. The C5515 device will not operate properly if TRST is not
asserted low during powerup.
5.20.1
JTAG ID (JTAGID) Register Description(s)
Table 5-57. JTAG ID Register
PRODUCT PREVIEW
HEX ADDRESS RANGE
ACRONYM
N/A
JTAGID
REGISTER NAME
JTAG Identification Register
COMMENTS
Read-only. Provides 32-bit
JTAG ID of the device.
The JTAG ID register is a read-only register that identifies to the customer the JTAG/Device ID. The
register hex value for C5515 is: 0x01B8F E02F. For the actual register bit names and their associated bit
field descriptions, see Figure 5-43 and Table 5-58.
31-28
27-12
11-1
0
VARIANT (4-Bit)
PART NUMBER (16-Bit)
MANUFACTURER (11-Bit)
LSB
R-0001
R-1011 1000 1111 1110
R-0000 0010 111
R-1
LEGEND: R = Read, W = Write, n = value at reset
Figure 5-43. JTAG ID Register Description - C5515 Register Value - 0x01B8F E02F
148
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
TMS320C5515
www.ti.com
SPRS645 – JANUARY 2010
Table 5-58. JTAG ID Register Selection Bit Descriptions
BIT
NAME
31:28
VARIANT
DESCRIPTION
27:12
PART NUMBER
11-1
MANUFACTURER
0
LSB
Variant (4-Bit) value. C5515 value: 0001.
Part Number (16-Bit) value. C5515 value: 1011 1000 1111 1110.
Manufacturer (11-Bit) value. C5515 value: 0000 0010 111.
LSB. This bit is read as a "1" for C5515 .
5.20.2 JTAG Test_port Electrical Data/Timing
Table 5-59. Timing Requirements for JTAG Test Port (see Figure 5-44)
CVDD = 1.05 V
CVDD = 1.3 V
MIN
UNIT
MAX
2
tc(TCK)
Cycle time, TCK
60
ns
3
tw(TCKH)
Pulse duration, TCK high
24
ns
4
tw(TCKL)
Pulse duration, TCK low
24
ns
5
tsu(TDIV-TCKH)
Setup time, TDI valid before TCK high
10
ns
6
tsu(TMSV-TCKH)
Setup time, TMS valid before TCK high
6
ns
7
th(TCKH-TDIV)
Hold time, TDI valid after TCK high
5
ns
8
th(TCKH-TDIV)
Hold time, TMS valid after TCK high
4
ns
Table 5-60. Switching Characteristics Over Recommended Operating Conditions for JTAG Test Port
(see Figure 5-44)
NO.
CVDD = 1.05 V
CVDD = 1.3 V
PARAMETER
MIN
1
td(TCKL-TDOV)
Delay time, TCK low to TDO valid
UNIT
MAX
30.5
ns
2
3
4
TCK
1
1
TDO
7
5
TDI
6
8
TMS
Figure 5-44. JTAG Test-Port Timing
Copyright © 2010, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
149
PRODUCT PREVIEW
NO.
TMS320C5515
SPRS645 – JANUARY 2010
www.ti.com
6 Mechanical Packaging and Orderable Information
The following table(s) show the thermal resistance characteristics for the PBGA–ZCH mechanical
package.
6.1
Thermal Data for ZCH
Table 6-1. Thermal Resistance Characteristics (PBGA Package) [ZCH]
＝C/W (1)
AIR FLOW
(m/s) (2)
1S0P
6.74
N/A
1S0P
14.5
N/A
2S2P
13.8
1S0P
57.0
2S2P
33.4
NO.
1
2
3
RΘJC
Junction-to-case
RΘJB
Junction-to-board
RΘJA
Junction-to-free air
4
0.00
0.50
5
RΘJMA
6
1.00
Junction-to-moving air
2.00
7
3.00
PRODUCT PREVIEW
8
0.09
9
0.00
0.50
10
PsiJT
Junction-to-package top
1.00
11
2.00
12
3.00
13
13.7
14
15
0.00
0.50
PsiJB
Junction-to-board
1.00
16
2.00
17
3.00
(1)
(2)
6.2
These measurements were conducted in a JEDEC defined 2S2P system and will change based on environment as well as application.
For more information, see these EIA/JEDEC standards – EIA/JESD51-2, Integrated Circuits Thermal Test Method Environment
Conditions - Natural Convection (Still Air) and JESD51-7, High Effective Thermal Conductivity Test Board for Leaded Surface Mount
Packages.
m/s = meters per second
Packaging Information
The following packaging information and addendum reflect the most current data available for the
designated device(s). This data is subject to change without notice and without revision of this document.
150
Mechanical Packaging and Orderable Information
Submit Documentation Feedback
Product Folder Link(s): TMS320C5515
Copyright © 2010, Texas Instruments Incorporated
PACKAGE OPTION ADDENDUM
www.ti.com
23-Jan-2010
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TMS320C5515AZCH10
ACTIVE
NFBGA
ZCH
196
184
TBD
Call TI
Call TI
TMS320C5515AZCH12
ACTIVE
NFBGA
ZCH
196
184
TBD
Call TI
Call TI
TMS320C5515AZCHA10
ACTIVE
NFBGA
ZCH
196
184
TBD
Call TI
Call TI
TMX320C5515AZCH12
ACTIVE
NFBGA
ZCH
196
184
Green (RoHS &
no Sb/Br)
SNAGCU
Lead/Ball Finish
MSL Peak Temp (3)
Level-3-260C-168 HR
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DLP® Products
www.dlp.com
Communications and
Telecom
www.ti.com/communications
DSP
dsp.ti.com
Computers and
Peripherals
www.ti.com/computers
Clocks and Timers
www.ti.com/clocks
Consumer Electronics
www.ti.com/consumer-apps
Interface
interface.ti.com
Energy
www.ti.com/energy
Logic
logic.ti.com
Industrial
www.ti.com/industrial
Power Mgmt
power.ti.com
Medical
www.ti.com/medical
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Space, Avionics &
Defense
www.ti.com/space-avionics-defense
RF/IF and ZigBee® Solutions www.ti.com/lprf
Video and Imaging
www.ti.com/video
Wireless
www.ti.com/wireless-apps
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2010, Texas Instruments Incorporated