SN74LVCZ161284A 19-BIT IEEE STD 1284 TRANSLATION TRANSCEIVER WITH ERROR-FREE POWER UP www.ti.com SCES358B – SEPTEMBER 2001 – REVISED MAY 2005 FEATURES • • • • • • • • DGG PACKAGE (TOP VIEW) Power-On Reset (POR) Prevents Printer Errors When Printer Is Turned On, But No Valid Signal Is at Pins A9–A13 Operates From 3 V to 3.6 V 1.4-kΩ Pullup Resistors Integrated on All Open-Drain Outputs Eliminate the Need for Discrete Resistors Designed for IEEE Std 1284-I (Level-1 Type) and IEEE Std 1284-II (Level-2 Type) Electrical Specifications Flow-Through Architecture Optimizes PCB Layout Ioff and Power-Up 3-State Support Hot Insertion Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II ESD Protection Exceeds JESD 22 – 4000-V Human-Body Model (A114-A) – 350-V Machine Model (A115-A) – 1500-V Charged-Device Model (C101) DESCRIPTION/ORDERING INFORMATION The SN74LVCZ161284A is designed for 3-V to 3.6-V VCC operation. This device provides asynchronous two-way communication between data buses. The control-function implementation minimizes external timing requirements. HD A9 A10 A11 A12 A13 VCC A1 A2 GND A3 A4 A5 A6 GND A7 A8 VCC PERI LOGIC IN A14 A15 A16 A17 HOST LOGIC OUT 1 48 2 47 3 46 4 45 5 44 6 43 7 42 8 41 9 40 10 39 11 38 12 37 13 36 14 35 15 34 16 33 17 32 18 31 19 30 20 29 21 28 22 27 23 26 24 25 DIR Y9 Y10 Y11 Y12 Y13 VCC CABLE B1 B2 GND B3 B4 B5 B6 GND B7 B8 VCC CABLE PERI LOGIC OUT C14 C15 C16 C17 HOST LOGIC IN This device has eight bidirectional bits; data can flow in the A-to-B direction when the direction-control (DIR) input is high and in the B-to-A direction when DIR is low. This device also has five drivers that drive the cable side and four receivers. The SN74LVCZ161284A has one receiver dedicated to the HOST LOGIC line and a driver to drive the PERI LOGIC line. The output drive mode is determined by the high-drive (HD) control pin. When HD is high, the outputs are in a totem-pole configuration and in an open-drain configuration when HD is low. This meets the drive requirements as specified in the IEEE Std 1284-I (level-1 type) and IEEE Std 1284-II (level-2 type) parallel peripheral-interface specifications. Except for HOST LOGIC IN and peripheral logic out (PERI LOGIC OUT), all cable-side pins have a 1.4-kΩ integrated pullup resistor. The pullup resistor is switched off if the associated output driver is in the low state or if the output voltage is above VCC CABLE. If VCC CABLE is off, PERI LOGIC OUT is set to low. The device has two supply voltages. VCC is designed for 3-V to 3.6-V operation. VCC CABLE supplies the inputs and output buffers of the cable side only and is designed for 3-V to 3.6-V and for 4.7-V to 5.5-V operation. Even when VCC CABLE is 3 V to 3.6 V, the cable-side I/O pins are 5-V tolerant. ORDERING INFORMATION PACKAGE (1) TA 0°C to 70°C (1) TSSOP – DGG Tape and reel ORDERABLE PART NUMBER SN74LVCZ161284AGR TOP-SIDE MARKING LVCZ161284A Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2001–2005, Texas Instruments Incorporated SN74LVCZ161284A 19-BIT IEEE STD 1284 TRANSLATION TRANSCEIVER WITH ERROR-FREE POWER UP www.ti.com SCES358B – SEPTEMBER 2001 – REVISED MAY 2005 DESCRIPTION/ORDERING INFORMATION (CONTINUED) The power-on reset (POR) ensures that the Y outputs (Y9–Y13) stay in the high state after power on until an associated input (A9–A13) goes high. When an associated input goes high, all Y outputs are activated, and noninverting signals of the associated inputs are driven through Y outputs. This special feature prevents printer system errors caused by deasserting the BUSY signal in the cable at power on. FUNCTION TABLE INPUTS 2 DIR HD L L L H H L H H OUTPUT MODE Open drain A9–A13 to Y9–Y13 and PERI LOGIC IN to PERI LOGIC OUT Totem pole B1–B8 to A1–A8 and C14–C17 to A14–A17 Totem pole B1–B8 to A1–A8, A9–A13 to Y9–Y13, PERI LOGIC IN to PERI LOGIC OUT, and C14–C17 to A14–A17 Open drain A1–A8 to B1–B8, A9–A13 to Y9–Y13, and PERI LOGIC IN to PERI LOGIC OUT Totem pole C14–C17 to A14–A17 Totem pole A1–A8 to B1–B8, A9–A13 to Y9–Y13, C14–C17 to A14–A17, and PERI LOGIC IN to PERI LOGIC OUT SN74LVCZ161284A 19-BIT IEEE STD 1284 TRANSLATION TRANSCEIVER WITH ERROR-FREE POWER UP www.ti.com SCES358B – SEPTEMBER 2001 – REVISED MAY 2005 LOGIC DIAGRAM VCC CABLE DIR HD 42 See Note A 48 See Note A 1 See Note B B1–B8 A1–A8 A9–A13 Y9–Y13 See Note C PERI LOGIC IN 19 30 C14–C17 A14–A17 HOST LOGIC OUT PERI LOGIC OUT 24 25 HOST LOGIC IN NOTES: A. The PMOS transistors prevent backdriving current from the signal pins to VCC CABLE when VCC CABLE is open or at GND. The PMOS transistor is turned off when the associated driver is in the low state. B. The PMOS transistor prevents backdriving current from the signal pins to VCC CABLE when VCC CABLE is open or at GND. C. Active input detection circuit forces Y9–Y13 to the high state after power on, until one of the A9–A13 pins goes high (see below). D A9 A10 A11 A12 A13 Timer Q OUT C R Power-On Reset Active Input Detection Circuit 3 SN74LVCZ161284A 19-BIT IEEE STD 1284 TRANSLATION TRANSCEIVER WITH ERROR-FREE POWER UP www.ti.com SCES358B – SEPTEMBER 2001 – REVISED MAY 2005 Absolute Maximum Ratings (1) over operating free-air temperature range (unless otherwise noted) MIN MAX VCC CABLE Supply voltage range –0.5 7 V VCC Supply voltage range –0.5 4.6 V Cable side (2) (3) –2 7 –0.5 VCC + 0.5 UNIT VI VO Input and output voltage range IIK Input clamp current VI < 0 –20 mA IOK Output clamp current VO < 0 –50 mA Except PERI LOGIC OUT ±50 IO Continuous output current Peripheral side (2) PERI LOGIC OUT Output high sink current θJA Package thermal impedance (4) Tstg Storage temperature range (1) (2) (3) (4) mA ±100 Continuous current through each VCC or GND ISK V ±200 VO = 5.5 V and VCC CABLE = 3 V –65 mA 65 mA 70 °C/W 150 °C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. The ac input voltage pulse duration is limited to 40 ns if the amplitude is greater than –0.5 V. The package thermal impedance is calculated in accordance with JESD 51-7. Recommended Operating Conditions (1) MIN MAX UNIT VCC CABLE Supply voltage for the cable side, VCC CABLE ≥ VCC 3 5.5 V VCC Supply voltage 3 3.6 V A, B, DIR, and HD VIH High-level input voltage C14–C17 2.3 HOST LOGIC IN 2.6 PERI LOGIC IN VIL Low-level input voltage VI Input voltage VO Open-drain output voltage IOH High-level output current 2 2 A, B, DIR, and HD 0.8 C14–C17 0.8 HOST LOGIC IN 1.6 PERI LOGIC IN 0.8 Peripheral side 0 VCC Cable side 0 5.5 HD low 0 5.5 HD high, B and Y outputs –4 (1) 4 Operating free-air temperature V mA 14 A outputs and HOST LOGIC OUT 4 PERI LOGIC OUT TA V –0.5 B and Y outputs Low-level output current V –14 A outputs and HOST LOGIC OUT PERI LOGIC OUT IOL V mA 84 0 70 All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. °C SN74LVCZ161284A 19-BIT IEEE STD 1284 TRANSLATION TRANSCEIVER WITH ERROR-FREE POWER UP www.ti.com SCES358B – SEPTEMBER 2001 – REVISED MAY 2005 Electrical Characteristics over recommended operating free-air temperature range, VCC CABLE = 5 V (unless otherwise noted) PARAMETER ∆Vt Hysteresis (VT+ – VT–) VOH VOL IOH = –14 mA HD high, A outputs, and HOST LOGIC OUT IOH = –4 mA PERI LOGIC OUT IOH = –0.5 mA B and Y outputs IOL = 14 mA Ioff UNIT V 0.2 3V 2.23 3.3 V (2) 2.4 3V IOH = –50 µA 2.4 3.15 V 3.1 V (2) 4.5 3.3 V 2.8 0.77 IOL = 50 µA 0.2 3V IOL = 4 mA 04 IOL = 84 mA V 0.9 VI = VCC 50 µA –3.5 mA VI = VCC or GND 3.6 V ±1 µA A1–A8 VO = VCC or GND 3.6 V ±20 µA VO = VCC CABLE 3.6 V 50 µA VO = GND (pullup resistors) 3.6 V (3) –3.5 mA VO = GND (pullup resistors) 3.6 V (3) –3.5 mA 350 µA –5 mA B and Y outputs B and Y outputs VI = GND (pullup resistors) 3.6 V (3) All inputs except B or C inputs Open-drain Y outputs IOZPD MAX 0.8 HD high, B and Y outputs B outputs IOZPU 3.3 V C inputs C inputs MIN TYP (1) 0.4 HOST LOGIC IN PERI LOGIC OUT IOZ VCC All inputs except C inputs and HOST LOGIC IN A outputs and HOST LOGIC OUT II TEST CONDITIONS VO = 5.5 V 0 to 1.5 V (4) VO = GND VO = 5.5 V 0 to 1.5 V (4) VO = GND Power-down input leakage, except A1–A8 or B1–B8 inputs VI or VO = 0 to 3.6 V Power-down output leakage, B1–B8 and Y9–Y13 outputs VI or VO = 0 to 5.5 V µA –5 mA 100 µA 0 (3) 100 3.6 V (5) VI = GND (12 × pullup) ICC 350 VI = VCC, IO = 0 45 3.6 V 70 3.6 V 0.8 mA Ci All inputs VI = VCC or GND 3.3 V 3 pF Cio I/O ports VO = VCC or GND 3.3 V 7 pF ZO Cable side IOH = –35 mA 3.3 V 45 R pullup Cable side VO = 0 V (in high-impedance state) 3.3 V (1) (2) (3) (4) (5) 1.15 Ω 1.65 kΩ Typical values are measured at VCC = 3.3 V, VCC CABLE = 5 V, and TA = 25°C. VCC CABLE = 4.7 V VCC CABLE = 3.6 V Connect the VCC pin and the VCC CABLE pin. VCC CABLE = 4.7 V 5 SN74LVCZ161284A 19-BIT IEEE STD 1284 TRANSLATION TRANSCEIVER WITH ERROR-FREE POWER UP www.ti.com SCES358B – SEPTEMBER 2001 – REVISED MAY 2005 Switching Characteristics over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 2 and Figure 3) FROM (INPUT) TO (OUTPUT) Totem pole A1–A8 B1–B8 Totem pole A9–A13 Y9–Y13 Totem pole B1–B8 A1–A8 Totem pole C14–C17 A14–A17 Totem pole PERI LOGIC IN PERI LOGIC OUT Totem pole HOST LOGIC IN HOST LOGIC OUT PARAMETER tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL tslew Totem pole B1–B8 and Y9–Y13 outputs tPZH tPHZ ten–tdis tPHZ tPLZ tr, tf Open drain tsk(o) (2) (1) (2) MIN TYP (1) MAX 1 22 1 22 1 20 1 20 1 10 1 10 1 11 1 11 1 13 1 13 1 13 1 13 0.05 0.4 20 HD B1–B8, Y9–Y13, and PERI LOGIC OUT 1 1 15 DIR A1–A8 1 15 1 15 1 15 DIR B1–B8 A1–A13 B1–B8 or Y9–Y13 A1–A8 or B1–B8 B1–B8 or A1–A8 1 2.5 UNIT ns ns ns ns ns ns V/ns ns ns ns 120 ns 10 ns Typical values are measured at VCC = 3.3 V, VCC CABLE = 5 V, and TA = 25°C. Skew is measured at 1/2 (VOH + VOL) for signals switching in the same direction. Operating Characteristics VCC = 3.3 V, TA = 25°C PARAMETER Cpd Power dissipation capacitance VCC = 3.3 V VCC CABLE = 5 V TA = 25°C TYP = 80 ns TEST CONDITIONS Outputs enabled CL = 0, f = 10 MHz TYP UNIT 45 pF VCC and VCC CABLE An (one of A9–A13) 50% VCC Initial Activation Time Y9–Y13, Other Than Yn 50% VCC CABLE One of pins A9–A13 is switched as shown above, and the other four inputs are forced at low state. Figure 1. Error-Free Circuit Timing 6 SN74LVCZ161284A 19-BIT IEEE STD 1284 TRANSLATION TRANSCEIVER WITH ERROR-FREE POWER UP www.ti.com SCES358B – SEPTEMBER 2001 – REVISED MAY 2005 PARAMETER MEASUREMENT INFORMATION VCC CABLE CL = 50 pF (see Note A) 62 Ω TP1 2.7 V Input (see Note B) 0V tf1 Sink Load From B or Y Output Under Test 95% (VCC CABLE = 5 V0.5 V) 50% (VCC CABLE = 5 V0.5 V) Output (see Note B) tr1 Source Load CL = 50 pF (see Note A) 62 Ω Output (see Note B) 1.9 V (VCC CABLE = 5 V0.5 V) 0.4 V VOLTAGE WAVEFORMS MEASURED AT TP1 SLEW RATE WAVEFORMS (B8−B1 AND Y13−Y9) SLEW RATE A-TO-B OR A-TO-Y LOAD (TOTEM POLE) VCC CABLE 2.7 V Input (see Note C) TP1 1.4 V 1.4 V 0V 500 Ω From B or Y Output CL = 50 pF (see Note A) 2V Output (see Note C) VOH 2V 0.8 V 0.8 V tr VOL tf VOLTAGE WAVEFORMS MEASURED AT TP1, B SIDE A-TO-B LOAD OR A-TO-Y LOAD (OPEN DRAIN) NOTES: A. CL includes probe and jig capacitance. B. When VCC CABLE is 3.3 V 0.3 V, slew rate is measured between 0.4 V and 0.9 V for the rising edge and between 2.4 V and 1.9 V for the falling edge. When VCC CABLE is 5 V 0.5 V, slew rate is measured between 0.4 V and 1.9 V for the rising edge and between 95% VCC CABLE and 50% VCC CABLE for the falling edge. tslew fall VCC 95% 50% t f1 C. D. E. F. G. tslew rise 1.9 V – 0.4 V tr1 Input rise (tr) and fall (tf) times are 3 ns. Rise and fall times (open drain) are <120 ns. The outputs are measured one at a time, with one transition per measurement. tPLZ and tPHZ are the same as tdis. tPZL and tPZH are the same as ten. tPLH and tPHL are the same as tpd. Figure 2. Load Circuits and Voltage Waveforms 7 SN74LVCZ161284A 19-BIT IEEE STD 1284 TRANSLATION TRANSCEIVER WITH ERROR-FREE POWER UP www.ti.com SCES358B – SEPTEMBER 2001 – REVISED MAY 2005 PARAMETER MEASUREMENT INFORMATION VCC × 2 V 500 Ω From Output Under Test S1 When Measuring the Cable Side, VCC CABLE × 2 V Open GND CL = 50 pF (see Note A) 500 Ω LOAD CIRCUIT Input (see Note B) 1.4 V 0V tPLH tPHL 50% VCC 2.7 V 1.4 V 1.4 V 0V tPZL tPLZ Output Waveform 1 S1 at VCC × 2 V (see Note C) VOH 1.4 V VOL + 0.3 V tPZH VOH Output S1 Open VCC × 2 V GND Output Control 2.7 V 1.4 V TEST tPLH/tPHL tPLZ/tPZL tPHZ/tPZH 50% VCC VOL VOL tPHZ Output Waveform 2 S1 at GND (see Note C) VOH − 0.3 V 1.4 V VOH 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES (B to A) B-TO-A LOAD (TOTEM POLE) VCC CABLE CL = 50 pF (see Note A) 500 Ω TP1 From B or Y Output Under Test tw 2.7 V Input (see Note D) Sink Load 1.4 V 1.4 V 0V tPHL tPLH tPLH tPHL VOH Source Load Output 500 Ω VOL + 1.4 V CL = 50 pF (see Note A) VOH − 1.4 V VOL VOLTAGE WAVEFORMS MEASURED AT TP1 PROPAGATION DELAY TIMES (A to B) A-TO-B LOAD OR A-TO-Y LOAD (TOTEM POLE) NOTES: A. CL includes probe and jig capacitance. B. Input rise and fall times are 3 ns. C. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control. D. Input rise and fall times are 3 ns. Pulse duration is 150 ns < tw < 10 µs. E. The outputs are measured one at a time, with one transition per measurement. F. tPLZ and tPHZ are the same as tdis. G. tPZL and tPZH are the same as ten. H. tPLH and tPHL are the same as tpd. Figure 3. Load Circuits and Voltage Waveforms 8 PACKAGE OPTION ADDENDUM www.ti.com 27-Sep-2007 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty 74LVCZ161284AGRG4 ACTIVE TSSOP DGG 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LVCZ161284AGR ACTIVE TSSOP DGG 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 25-Jan-2008 TAPE AND REEL BOX INFORMATION Device SN74LVCZ161284AGR Package Pins DGG 48 Site Reel Diameter (mm) Reel Width (mm) A0 (mm) B0 (mm) K0 (mm) P1 (mm) SITE 41 330 24 8.6 15.8 1.8 12 Pack Materials-Page 1 W Pin1 (mm) Quadrant 24 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 25-Jan-2008 Device Package Pins Site Length (mm) Width (mm) Height (mm) SN74LVCZ161284AGR DGG 48 SITE 41 346.0 346.0 41.0 Pack Materials-Page 2 MECHANICAL DATA MTSS003D – JANUARY 1995 – REVISED JANUARY 1998 DGG (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 48 PINS SHOWN 0,27 0,17 0,50 48 0,08 M 25 6,20 6,00 8,30 7,90 0,15 NOM Gage Plane 1 0,25 24 0°– 8° A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 48 56 64 A MAX 12,60 14,10 17,10 A MIN 12,40 13,90 16,90 DIM 4040078 / F 12/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID RF/IF and ZigBee® Solutions amplifier.ti.com dataconverter.ti.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lprf Applications Audio Automotive Broadband Digital Control Medical Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/medical www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright 2008, Texas Instruments Incorporated