TI SN74ABT16853DLR

SN54ABT16853, SN74ABT16853
DUAL 8-BIT TO 9-BIT PARITY BUS TRANSCEIVERS
SCBS153B – OCTOBER 1992 – REVISED JANUARY 1997
D
D
D
D
D
D
D
D
D
D
SN54ABT16853 . . . WD PACKAGE
SN74ABT16853 . . . DGG OR DL PACKAGE
(TOP VIEW)
Members of the Texas Instruments
Widebus  Family
State-of-the-Art EPIC-ΙΙB  BiCMOS Design
Significantly Reduces Power Dissipation
Latch-Up Performance Exceeds 500 mA
Per JEDEC Standard JESD-17
Typical VOLP (Output Ground Bounce) < 1 V
at VCC = 5 V, TA = 25°C
Distributed VCC and GND Pin Configuration
Minimizes High-Speed Switching Noise
Flow-Through Architecture Optimizes
PCB Layout
High-Drive Outputs (–32-mA IOH, 64-mA IOL)
Parity-Error Flag With Parity
Generator/Checker
Latch for Storage of the Parity-Error Flag
Package Options Include Plastic 300-mil
Shrink Small-Outline (DL) and Thin Shrink
Small-Outline (DGG) Packages and 380-mil
Fine-Pitch Ceramic Flat (WD) Package
Using 25-mil Center-to-Center Spacings
1OEB
1LE
1ERR
GND
1A1
1A2
VCC
1A3
1A4
1A5
GND
1A6
1A7
1A8
2A1
2A2
2A3
GND
2A4
2A5
2A6
VCC
2A7
2A8
GND
2ERR
2LE
2OEB
description
The ’ABT16853 dual 8-bit to 9-bit parity
transceivers are designed for communication
between data buses. When data is transmitted
from the A bus to the B bus, a parity bit is
generated. When data is transmitted from the
B bus to the A bus, with its corresponding parity
bit, the open-collector parity-error (ERR) output
indicates whether or not an error in the B data has
occurred. The output-enable (OEA and OEB)
inputs can be used to disable the device so that
the buses are effectively isolated. The ’ABT16853
provide true data at the outputs.
1
56
2
55
3
54
4
53
5
52
6
51
7
50
8
49
9
48
10
47
11
46
12
45
13
44
14
43
15
42
16
41
17
40
18
39
19
38
20
37
21
36
22
35
23
34
24
33
25
32
26
31
27
30
28
29
1OEA
1CLR
1PARITY
GND
1B1
1B2
VCC
1B3
1B4
1B5
GND
1B6
1B7
1B8
2B1
2B2
2B3
GND
2B4
2B5
2B6
VCC
2B7
2B8
GND
2PARITY
2CLR
2OEA
A 9-bit parity generator/checker generates a parity-odd (PARITY) output and monitors the parity of the I/O ports
with the ERR flag. The parity-error output can be passed, sampled, stored, or cleared from the latch using the
latch-enable (LE) and clear (CLR) control inputs. When both OEA and OEB are low, data is transferred from
the A bus to the B bus, and inverted parity is generated. Inverted parity is a forced error condition that gives the
designer more system diagnostic capability.
To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup
resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
EPIC-ΙΙB and Widebus are trademarks of Texas Instruments Incorporated.
Copyright  1997, Texas Instruments Incorporated
UNLESS OTHERWISE NOTED this document contains PRODUCTION
DATA information current as of publication date. Products conform to
specifications per the terms of Texas Instruments standard warranty.
Production processing does not necessarily include testing of all
parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SN54ABT16853, SN74ABT16853
DUAL 8-BIT TO 9-BIT PARITY BUS TRANSCEIVERS
SCBS153B – OCTOBER 1992 – REVISED JANUARY 1997
description (continued)
The SN54ABT16853 is characterized for operation over the full military temperature range of –55°C to 125°C.
The SN74ABT16853 is characterized for operation from –40°C to 85°C.
FUNCTION TABLE
INPUTS
OUTPUT AND I/O
AI
Σ OF H
BI†
Σ OF H
A
B
NA
NA
A
B
NA
NA
CLR
LE
L
H
X
X
H
L
X
L
NA
H
L
H
H
NA
X
X
NA
NA
NC
Store error flag
X
X
L
H
X
X
X
NA
NA
H
Clear error-flag register
H
H
X
L
H
X
X
L
L Odd
X
L
H Even
H
L
H
L
X
X
Odd
Odd
Odd
Even
L
H
NA
H
L
A data to B bus and
generate parity
B data to A bus and
check parity
NC
X
Z
Z
Z
H
H
Isolation§
(parity check)
L
NA
NA
A
Even
H
L
NA = not applicable, NC = no change, X = don’t care
† Summation of high-level inputs includes PARITY along with Bi inputs.
‡ Output states shown assume ERR was previously high.
§ In this mode, ERR (when clocked) shows inverted parity of the A bus.
2
FUNCTION
OEA
Even
PARITY
ERR‡
OEB
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
NA
A data to B bus and
generate inverted parity
SN54ABT16853, SN74ABT16853
DUAL 8-BIT TO 9-BIT PARITY BUS TRANSCEIVERS
SCBS153B – OCTOBER 1992 – REVISED JANUARY 1997
logic diagram (each transceiver) (positive logic)
A1–A8
8
8x
8
B1–B8
EN
8x
8
EN
OEB
OEA
PARITY
8
8
MUX
1
1
2k
9
1
P
1
G1
ERR
LE
CLR
ERROR-FLAG FUNCTION TABLE
INPUTS
CLR
LE
L
L
H
L
L
H
H
H
INTERNAL
TO DEVICE
OUTPUT
POINT P
ERRn–1†
L
H
X
OUTPUT
ERR
L
H
L
X
X
L
L
H
H
H
X
X
H
L
L
H
H
X
FUNCTION
Pass
L
Sample
Clear
Store
† State of ERR before changes at CLR, LE, or point P
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SN54ABT16853, SN74ABT16853
DUAL 8-BIT TO 9-BIT PARITY BUS TRANSCEIVERS
SCBS153B – OCTOBER 1992 – REVISED JANUARY 1997
error-flag waveforms
H
OEB
L
H
OEA
L
Even
Bi + PARITY
Odd
H
LE
L
H
CLR
L
H
ERR
L
Pass
Store
Sample
Clear
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V
Input voltage range, VI (except I/O ports) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V
Voltage range applied to any output in the high or power-off state, VO . . . . . . . . . . . . . . . . . . . –0.5 V to 5.5 V
Current into any output in the low state, IO: SN54ABT16853 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 mA
SN74ABT16853 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 mA
Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –18 mA
Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA
Package thermal impedance, θJA (see Note 2): DGG package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81°C/W
DL package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74°C/W
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed.
2. The package thermal impedance is calculated in accordance with EIA/JEDEC Std JESD51.
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN54ABT16853, SN74ABT16853
DUAL 8-BIT TO 9-BIT PARITY BUS TRANSCEIVERS
SCBS153B – OCTOBER 1992 – REVISED JANUARY 1997
recommended operating conditions (see Note 3)
SN54ABT16853
VCC
VIH
Supply voltage
VIL
VI
Low-level input voltage
VOH
IOH
High-level output voltage
ERR
High-level output current
Except ERR
IOL
∆t/∆v
Low-level output current
High-level input voltage
SN74ABT16853
MIN
MAX
MIN
MAX
4.5
5.5
4.5
5.5
2
2
0.8
Input voltage
0
Input transition rise or fall rate
Outputs enabled
TA
Operating free-air temperature
NOTE 3: Unused pins (input or I/O) must be held high or low to prevent them from floating.
–55
UNIT
V
V
0.8
V
VCC
5.5
V
–24
–32
mA
48
64
mA
10
10
ns/V
85
°C
VCC
5.5
125
0
–40
V
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
VIK
VOH
All outputs
except ERR
TEST CONDITIONS
VCC = 4.5 V,
VCC = 4.5 V,
II = –18 mA
IOH = –3 mA
VCC = 5 V,
5V
VCC = 4
4.5
VOL
Vhys
IOH
Ioff
ICEX
II
IIL
IO‡
VCC = 4
4.5
5V
SN54ABT16853
MIN
–1.2
MAX
SN74ABT16853
MIN
–1.2
2.5
3
2.5
IOH = –3 mA
IOH = –24 mA
3
3.4
3
IOH = –32 mA
IOL = 24 mA
2*
MAX
–1.2
3
IOL = 64 mA
2.7
Outputs high
Control inputs
A or B ports
A or B ports
A or B ports
VCC = 4.5 V,
VCC = 0,
VOH = 5.5 V
VI or VO ≤ 4.5 V
VCC = 5.5 V,
VO = 5.5 V
VCC = 0,
VCC = 5.5 V,
VI = GND
VO = 2.5 V
0.55
0.3
0.55*
0.55
0.55
VCC =5.5 V,
VCC = 5.5 V,
VO = 2.7 V
VO = 0.5 V
VCC = 5.5 V,
IO = 0,
VI = VCC or GND
Outputs high
Outputs low
Outputs disabled
Ci
Control inputs
Cio
A or B ports
VI = 2.5 V or 0.5 V
VO = 2.5 V or 0.5 V
20
µA
±100
µA
µA
50
50
50
±1
±1
±1
±100
±100
±100
–50
–180
–50
–50
–180
–50
µA
–50
µA
–180
mA
50
50
50
µA
–50
–50
–50
µA
1.5
2
2
2
32
40
40
40
1
2
2
2
50
50
50
VCC = 5.5 V, One input at 3.4 V,
Other inputs at VCC or GND
∆ICC¶
20
±100
–100
V
mV
20
–50
V
2
0.25
VCC = 5
5.5
5 V,
V VI = VCC or GND
UNIT
V
2
100
ERR
IOZH§
IOZL§
ICC
TA = 25°C
MIN TYP†
MAX
mA
µA
3
pF
9
pF
* On products compliant to MIL-PRF-38535, this parameter does not apply.
† All typical values are at VCC = 5 V.
‡ Not more than one output should be tested at a time, and the duration of the test should not exceed one second.
§ The parameters IOZH and IOZL include the input leakage current.
¶ This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND.
PRODUCT PREVIEW information concerns products in the formative or
design phase of development. Characteristic data and other
specifications are design goals. Texas Instruments reserves the right to
change or discontinue these products without notice.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
SN54ABT16853, SN74ABT16853
DUAL 8-BIT TO 9-BIT PARITY BUS TRANSCEIVERS
SCBS153B – OCTOBER 1992 – REVISED JANUARY 1997
timing requirements over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted) (see Figure 1)
VCC = 5 V,
TA = 25°C
MIN
tw
Pulse duration
tsu
Setup time
th
Hold time
LE high or low
CLR low
A, B, and PARITY before LE↓
SN54ABT16853
MAX
MIN
MAX
SN74ABT16853
MIN
8.5
8.5
8.5
4
4
4
10
10
10
CLR before LE↓
0
0
0
A, B, and PARITY after LE↓
0
0
0
CLR after LE↓
0
0
0
UNIT
MAX
ns
ns
ns
switching characteristics over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted) (see Figure 1)
FROM
(INPUT)
TO
(OUTPUT)
tPLH
tPHL
A or B
B or A
tPLH
tPHL
A or OE
PARITY
tPLH
CLR
ERR
PARAMETER
tPZH
tPZL
OE
A or B
tPHZ
tPLZ
OE
A or B
tPZH
tPZL
OE
PARITY
tPHZ
tPLZ
OE
PARITY
tPLH
tPHL
LE
ERR
tPLH
tPHL
A B,
A,
B or PARITY
ERR
VCC = 5 V,
TA = 25°C
SN54ABT16853
MIN
TYP
MAX
MIN
MAX
MIN
MAX
1.5
2.5
3.3
1.5
4.2
1.5
4.1
2
3.1
3.9
2
4.5
2
4.3
2
4.6
5.9
2
7.3
2
7.1
2
4.8
6.2
2
7.6
2
7.2
2
3.7
5.1
2
5.9
2
5.7
2
3.9
4.9
2
5.8
2
5.6
2.5
4.3
5.1
2.5
6.2
2.5
6
2
3.6
4.5
2
5.5
2
5.4
1.5
3
3.8
1.5
4.7
1.5
4.3
2
3.6
5
2
5.8
2
5.7
2.5
4.4
5.8
2.5
6.7
2.5
6.5
1.5
3.2
4
1.5
4.8
1.5
4.7
1.5
2.9
3.7
1.5
4.2
1.5
4.1
2
3.5
4.2
2
5
2
4.8
2
3.4
4.4
2
5.2
2
4.9
2
4.5
6.3
2
7.5
2
7.2
2
4.8
6.3
2
7.7
2
7.4
PRODUCT PREVIEW information concerns products in the formative or
design phase of development. Characteristic data and other
specifications are design goals. Texas Instruments reserves the right to
change or discontinue these products without notice.
6
POST OFFICE BOX 655303
SN74ABT16853
• DALLAS, TEXAS 75265
UNIT
ns
ns
ns
ns
ns
ns
ns
ns
ns
SN54ABT16853, SN74ABT16853
DUAL 8-BIT TO 9-BIT PARITY BUS TRANSCEIVERS
SCBS153B – OCTOBER 1992 – REVISED JANUARY 1997
PARAMETER MEASUREMENT INFORMATION
7V
S1
500 Ω
From Output
Under Test
Open
GND
CL = 50 pF
(see Note A)
500 Ω
TEST
S1
tPLH/tPHL
tPLZ/tPZL
tPHZ/tPZH
Open
7V
Open
ERR
S1
tPHL (see Note E)
tPLH (see Note F)
7V
7V
LOAD CIRCUIT
3V
Timing Input
1.5 V
0V
tw
tsu
3V
th
3V
Input
1.5 V
1.5 V
Data Input
1.5 V
1.5 V
0V
0V
VOLTAGE WAVEFORMS
PULSE DURATION
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
3V
1.5 V
Input
1.5 V
0V
VOH
1.5 V
Output
1.5 V
VOL
VOH
Output
1.5 V
1.5 V
VOL
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
INVERTING AND NONINVERTING OUTPUTS
1.5 V
0V
tPLZ
Output
Waveform 1
S1 at 7 V
(see Note B)
tPLH
tPHL
1.5 V
tPZL
tPHL
tPLH
3V
Output
Control
Output
Waveform 2
S1 at Open
(see Note B)
1.5 V
tPZH
3.5 V
VOL + 0.3 V
VOL
tPHZ
1.5 V
VOH – 0.3 V
VOH
≈0V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
LOW- AND HIGH-LEVEL ENABLING
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns.
D. The outputs are measured one at a time with one transition per measurement.
E. tPHL is measured at 1.5 V.
F. tPLH is measured at VOL + 0.3 V.
Figure 1. Load Circuit and Voltage Waveforms
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
PACKAGE OPTION ADDENDUM
www.ti.com
27-Sep-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
74ABT16853DGGRE4
ACTIVE
TSSOP
DGG
56
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
74ABT16853DGGRG4
ACTIVE
TSSOP
DGG
56
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN74ABT16853DGGR
ACTIVE
TSSOP
DGG
56
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN74ABT16853DL
ACTIVE
SSOP
DL
56
20
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN74ABT16853DLG4
ACTIVE
SSOP
DL
56
20
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN74ABT16853DLR
ACTIVE
SSOP
DL
56
1000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN74ABT16853DLRG4
ACTIVE
SSOP
DL
56
1000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
22-Sep-2007
TAPE AND REEL BOX INFORMATION
Device
Package Pins
Site
Reel
Diameter
(mm)
Reel
Width
(mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
SN74ABT16853DGGR
DGG
56
SITE 41
330
24
8.6
15.6
1.8
12
24
Q1
SN74ABT16853DLR
DL
56
SITE 41
330
32
11.35
18.67
3.1
16
32
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
22-Sep-2007
Device
Package
Pins
Site
Length (mm)
Width (mm)
Height (mm)
SN74ABT16853DGGR
DGG
56
SITE 41
346.0
346.0
0.0
SN74ABT16853DLR
DL
56
SITE 41
346.0
346.0
0.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties
may be subject to additional restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Telephony
www.ti.com/telephony
Low Power
Wireless
www.ti.com/lpw
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated