SM5009 series Crystal Oscillator Module ICs OVERVIEW The SM5009 series are crystal oscillator module ICs that incorporate low crystal current type oscillating circuit to limit oscillator-stage current, so that they can reduce crystal current lower than the existing products. Since the oscillating circuit has oscillator capacitors with excellent frequency response and feedback resistor built-in, just connecting crystal realizes stable fundamental oscillation responding up to 40MHz. The SM5009 series are ideal for SMD type crystal oscillator using a strip-shaped crystal blank. FEATURES ■ ■ ■ ■ ■ ■ ■ ■ Low crystal current oscillator Up to 40MHz operating frequency range (fundamental oscillation) Operating supply voltage range • 3V operation: 2.7 to 3.6V • 5V operation: 4.5 to 5.5V –40 to 85°C operating temperature range Oscillation capacitors CG, CD built-in Inverter amplifier feedback resistor built-in Standby function • Oscillator stops (AL series), high impedance in standby mode Low standby current ■ ■ ■ ■ ■ ■ ■ • Power-save pull-up resistor built-in (AL series) Frequency divider built-in (fO, fO/2, fO/4, fO/8, fO/16, fO/32 determined by internal connection) Output drive capability • AL×, AN×, AK×, CN×: 16mA (VDD = 4.5V) • AH×: 4mA (VDD = 4.5V) Output load: CL = 50pF max. Output duty level • CMOS level (1/2 VDD): AL×, AN×, AH×, CN× • TTL level (1.4V): AK× Molybdenum-gate CMOS process 8-pin SOP (SM5009×××S) Chip form (CF5009×××) SERIES CONFIGURATION Version1 CF5009AL1 CF5009AL2 CF5009AL3 CF5009AL4 CF5009AL5 CF5009AL6 CF5009AN1 CF5009AN2 CF5009AN3 CF5009AN4 CF5009AN5 CF5009AN6 CF5009CN1 CF5009CN2 CF5009AK1 CF5009AK2 CF5009AH1 CF5009AH2 CF5009AH3 CF5009AH4 3V operation 5V operation Recommended Recommended Output Output Output operating operating load3 (max) load3 (max) duty level frequency frequency [pF] [pF] range2 [MHz] range2 [MHz] Up to 40 50 Up to 40 50 CMOS CMOS Up to 40 30 Up to 40 50 CMOS/TTL Up to 30 15 Up to 30 50 CMOS – – Up to 40 15 TTL Up to 16 15 Up to 30 15 CMOS Standby mode Output frequency fO fO/2 fO/4 fO/8 fO/16 fO/32 fO fO/2 fO/4 fO/8 fO/16 fO/32 fO fO/2 fO fO/2 fO fO/2 fO/4 fO/8 INH Input level Oscillator stop function Output state CMOS Yes Hi-Z TTL No Hi-Z TTL No Hi-Z TTL No Hi-Z TTL No Hi-Z 1. Package devices (8-pin SOP) have designation SM5009×××S. 2. The recommended operating frequency is a yardstick value derived from the crystal used for NPC characteristics authentication. However, the oscillator frequency band is not guaranteed. Specifically, the characteristics can vary greatly due to crystal characteristics and mounting conditions, so the oscillation characteristics of components must be carefully evaluated. 3. Output load value is the maximum load capacitance that allows drive. APPLICATIONS ■ SMD type crystal oscillator module ORDERING INFORMATION Device SM5009×××S CF5009×××–1 Package 8-pin SOP Chip form NIPPON PRECISION CIRCUITS INC.—1 SM5009 series PAD LAYOUT PINOUT (Unit: µm) (Top view) Q VDD (920,1220) HA5009 Y (0,0) INH XT XT VSS INH 1 8 VDD XT 2 7 NC XT 3 6 NC VSS 4 5 Q X Chip size: 0.92 × 1.22 mm Chip thickness: 300 ± 30 µm Chip base: VDD level PIN DESCRIPTION and PAD DIMENSIONS Pad dimensions [µm] Number Name I/O Description 1 INH I 2 XT I 3 XT O Amplifier output. 4 VSS – Ground 5 Q O Output. Output frequency (fO, fO/2, fO/4, fO/8, fO/16, fO/32) determined by internal connection 6 NC – 7 NC – 8 VDD – X Y Output state control input. Standby mode when LOW, pull-up resistor built-in. In the case of the CF5009AL×, the oscillator stops and power-save pull-up resistor built in to reduce current consumption at standby mode. 195 212 Amplifier input. 385 212 575 212 766 212 765 1062 No connection – – No connection – – Supply voltage 162 1062 Crystal oscillator connection pins. Crystal oscillator connected between XT and XT NIPPON PRECISION CIRCUITS INC.—2 SM5009 series PACKAGE DIMENSIONS (Unit: mm) • 8-pin SOP 0.15 + 0.1 0.4 0.2 6.2 0.3 4.4 0.2 − 0.05 0.695typ 1.5 0.1 0.05 0.05 5.2 0.3 1.27 0 to 10 0.10 0.4 0.1 0.12 M BLOCK DIAGRAM VDD VSS XT CGp Rf CDp 1/2 1/2 1/2 1/2 1/2 XT CGn CDn Q INH Notes. The SM5009 series reduce crystal current by limiting driving current of oscillating-stage inverter and inhibiting oscillating amplitude. Depending on the characteristics of using crystal or the mounting condition, they may not oscillate normally. Please evaluate the oscillation start-up characteristics adequately with your actual device. NIPPON PRECISION CIRCUITS INC.—3 SM5009 series FUNCTIONAL DESCRIPTION Standby Function 5009 AL× series When INH goes LOW, the oscillator stops and the oscillator output on Q becomes high impedance. 5009AH×, AK×, AN×, CN× series When INH goes LOW, the output on Q becomes high impedance, but internally the oscillator does not stop. Version AL× series INH Q Oscillator HIGH (or open) Any fO , fO/2, fO/4, fO/8, fO/16 or fO/32 output frequency Normal operation LOW HIGH (or open) AH×, AK×, AN×, CN× series LOW High impedance Stopped Any fO , fO/2, fO/4, fO/8, fO/16 or fO/32 output frequency Normal operation High impedance Normal operation Power-save Pull-up Resistance (AL× series only) The INH pull-up resistance changes in response to the input level (HIGH or LOW). When INH goes LOW (standby state), the pull-up resistance becomes large to reduce the current consumption during standby. Current consumption and Output waveform with NPC’s standard crystal Cb L Ca f [MHz] R [Ω] L [mH] Ca [fF] Cb [pF] 30 17.2 4.36 6.46 2.26 40 16.8 2.90 5.47 2.08 R NIPPON PRECISION CIRCUITS INC.—4 SM5009 series SPECIFICATIONS Absolute Maximum Ratings VSS = 0V unless otherwise noted. Parameter Symbol Supply voltage range Rating Unit VDD Condition −0.5 to +7.0 V VIN −0.5 to VDD + 0.5 V Output voltage range VOUT −0.5 to VDD + 0.5 V Operating temperature range Topr −40 to +85 °C Input voltage range Storage temperature range Tstg Output current IOUT Power dissipation PD Chip form −65 to +150 8-pin SOP −55 to +125 8-pin SOP °C 25 mA 500 mW Recommended Operating Conditions VSS = 0V unless otherwise noted. Parameter Symbol Version AH× AK× Supply voltage VDD Condition min typ max f ≤ 30MHz 4.5 – 5.5 f ≤ 16MHz 2.7 – 3.3 f ≤ 40MHz 4.5 – 5.5 V f ≤ 40MHz 2.7 – 5.5 V f ≤ 30MHz 2.7 – 5.5 V f ≤ 40MHz 2.7 – 5.5 f ≤ 30MHz 2.3 – 2.7 f ≤ 20MHz 2.25 – 2.75 f ≤ 40MHz 2.7 – 5.5 8-pin SOP f ≤ 14.4MHz All version AH× AK× – 2.7 – VDD f ≤ 30MHz, 4.5V ≤ VDD ≤ 5.5V − 40 – + 85 − 20 – + 80 f ≤ 30MHz − 40 – + 85 30MHz < f ≤ 40MHz − 20 – + 80 f ≤ 40MHz, 2.7V ≤ VDD < 4.5V − 20 – + 80 f ≤ 40MHz, 4.5V ≤ VDD ≤ 5.5V − 40 – + 85 f ≤ 40MHz, 2.7V ≤ VDD < 4.5V − 20 – + 80 f ≤ 40MHz, 4.5V ≤ VDD ≤ 5.5V − 20 – + 80 AN× 8-pin SOP − 40 – + 85 f ≤ 30MHz, 2.7V ≤ VDD < 4.5V f ≤ 30MHz, 4.5V ≤ VDD ≤ 5.5V − 10 – + 70 f ≤ 30MHz, 4.5V ≤ VDD ≤ 5.5V − 40 – + 85 f ≤ 40MHz, 2.7V ≤ VDD ≤ 5.5V − 40 – + 85 f ≤ 30MHz, 2.3V ≤ VDD ≤ 2.7V − 20 – + 80 f ≤ 20MHz, 2.25V ≤ VDD ≤ 2.75V − 20 – + 80 f ≤ 40MHz, 2.7V ≤ VDD ≤ 5.5V − 20 – + 80 f ≤ 30MHz, 2.7V ≤ VDD ≤ 5.5V − 40 – + 85 f ≤ 14.4MHz, 2.4V ≤ VDD ≤ 2.7V − 20 – + 80 TOPR CN× 2.4 VSS f ≤ 16MHz, 2.7V ≤ VDD ≤ 3.6V Chip form Operating temperature V AN× AL× VIN Unit CN× Chip form Input voltage Rating Chip form AL× 8-pin SOP V V °C °C °C °C °C NIPPON PRECISION CIRCUITS INC.—5 SM5009 series Electrical Characteristics 5009AL× series 3V operation: VDD = 2.7 to 3.3V, VSS = 0V, Ta = −40 to 85°C unless otherwise noted. Rating Parameter Symbol Condition Unit min typ max HIGH-level output voltage VOH Q: Measurement cct 1, IOH = 8mA 2.2 – – V LOW-level output voltage VOL Q: Measurement cct 1, IOL = 8mA – – 0.4 V HIGH-level input voltage VIH INH 0.7VDD – – V LOW-level input voltage VIL INH – – 0.3VDD V – 10 IZ Q: Measurement cct 2, INH = LOW, VOH = VDD – Output leakage current Q: Measurement cct 2, INH = LOW, VOL = VSS – – 10 CF5009AL1 – 8 17 CF5009AL2 – 5 11 CF5009AL3 – 4 9 CF5009AL4 – 3 7 CF5009AL5 – 3 6 CF5009AL6 – 2 5 SM5009AL1S – 8 17 SM5009AL2S – 5 11 SM5009AL3S – 4 9 SM5009AL4S – 3 7 SM5009AL5S – 3 6 SM5009AL6S – 2 5 – 2 5 µA INH = open, Measurement cct 3, load cct 2, CL = 15pF, 40MHz crystal oscillator Current consumption IDD mA INH = open, Measurement cct 3, load cct 2, CL = 15pF, 40MHz crystal oscillator, Ta = –20 to +80°C Standby current IST µA INH = VSS, Measurement cct 3 RUP1 Measurement cct 4, VDD = 3V, INH = VSS 0.6 – 12 MΩ RUP2 Measurement cct 4, VDD = 3V, INH = 2.1V 40 – 200 kΩ Negative resistance −RL VDD = 3V, Ta = 25°C, 40MHz – –200 – Ω Feedback resistance Rf 0.4 – 1.1 MΩ 5.58 6 6.42 pF 9.3 10 10.7 pF INH pull-up resistance Built-in capacitance CG CD Measurement cct 5 Design value. A monitor pattern on a wafer is tested. NIPPON PRECISION CIRCUITS INC.—6 SM5009 series 5V operation: VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to 85°C unless otherwise noted. Rating Parameter Symbol Condition Unit min typ max HIGH-level output voltage VOH Q: Measurement cct 1, IOH = 16mA 4.0 – – V LOW-level output voltage VOL Q: Measurement cct 1, IOL = 16mA – – 0.4 V HIGH-level input voltage VIH INH 0.7VDD – – V LOW-level input voltage VIL INH – – 0.3VDD V – 10 IZ Q: Measurement cct 2, INH = LOW, VOH = VDD – Output leakage current Q: Measurement cct 2, INH = LOW, VOL = VSS – – 10 CF5009AL1 – 12 26 CF5009AL2 – 8 17 CF5009AL3 – 6 13 CF5009AL4 – 5 11 CF5009AL5 – 5 10 CF5009AL6 – 4 9 SM5009AL1S – 12 26 SM5009AL2S – 8 17 SM5009AL3S – 6 13 SM5009AL4S – 5 11 SM5009AL5S – 5 10 SM5009AL6S – 4 9 – 6 15 µA INH = open, Measurement cct 3, load cct 2, CL = 15pF, 40MHz crystal oscillator Current consumption IDD mA INH = open, Measurement cct 3, load cct 2, CL = 15pF, 40MHz crystal oscillator, Ta = –20 to +80°C Standby current IST µA INH = VSS, Measurement cct 3 RUP1 Measurement cct 4, VDD = 5V, INH = VSS 0.3 – 6 MΩ RUP2 Measurement cct 4, VDD = 5V, INH = 3.5V 40 – 200 kΩ Negative resistance −RL VDD = 5V, Ta = 25°C, 40MHz – –400 – Ω Feedback resistance Rf 0.4 – 1.1 MΩ 5.58 6 6.42 pF 9.3 10 10.7 pF INH pull-up resistance Built-in capacitance CG CD Measurement cct 5 Design value. A monitor pattern on a wafer is tested. NIPPON PRECISION CIRCUITS INC.—7 SM5009 series 5009AN×/CN× series 3V operation: VDD = 2.7 to 3.3V, VSS = 0V, Ta = −20 to 80°C unless otherwise noted. Rating Parameter Symbol Condition Unit SM5009AN1S, CF5009AN1 SM5009AN2S, CF5009AN2 HIGH-level output voltage VOH Q: Measurement cct 1, IOH = 8mA SM5009AN3S, CF5009AN3 SM5009AN4S, CF5009AN4 SM5009AN5S, CF5009AN5 SM5009AN6S, CF5009AN6 SM5009CN1S, CF5009CN1 SM5009CN2S, CF5009CN2 min typ max 2.2 – – V 2.1 – – – – 0.4 V LOW-level output voltage VOL Q: Measurement cct 1, IOL = 8mA HIGH-level input voltage VIH INH 2.0 – – V LOW-level input voltage VIL INH – – 0.3 V – 10 IZ Q: Measurement cct 2, INH = LOW, VOH = VDD – Output leakage current Q: Measurement cct 2, INH = LOW, VOL = VSS – – 10 SM5009AN1S, CF5009AN1 – 8 17 SM5009AN2S, CF5009AN2 – 5 11 SM5009AN3S, CF5009AN3 – 4 9 SM5009AN4S, CF5009AN4 – 3 7 SM5009AN5S, CF5009AN5 – 3 6 SM5009AN6S, CF5009AN6 – 2 5 SM5009CN1S, CF5009CN1 – 7 15 SM5009CN2S, CF5009CN2 – 4 9 INH = open, Measurement cct 3, load cct 2, CL = 15pF, 40MHz crystal oscillator Current consumption IDD INH = open, Measurement cct 3, load cct 2, CL = 15pF, 30MHz crystal oscillator, Ta = –10 to +70°C µA mA INH pull-up resistance RUP Measurement cct 4, VDD = 3V, INH = VSS 40 – 200 kΩ Negative resistance −RL VDD = 3V, Ta = 25°C, 40MHz – –100 – Ω Feedback resistance Rf 0.4 – 1.1 MΩ 5.58 6 6.42 pF 9.3 10 10.7 pF Built-in capacitance CG CD Measurement cct 5 Design value. A monitor pattern on a wafer is tested. NIPPON PRECISION CIRCUITS INC.—8 SM5009 series 5V operation: VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to 85°C unless otherwise noted. Rating Parameter HIGH-level output voltage Symbol VOH Condition Q: Measurement cct 1, IOH = 16mA Unit min typ max SM5009AN1S, CF5009AN1 SM5009AN2S, CF5009AN2 4.0 – – SM5009AN3S, CF5009AN3 SM5009AN4S, CF5009AN4 SM5009AN5S, CF5009AN5 SM5009AN6S, CF5009AN6 SM5009CN1S, CF5009CN1 SM5009CN2S, CF5009CN2 3.9 – – – – 0.4 V V LOW-level output voltage VOL Q: Measurement cct 1, IOL = 16mA HIGH-level input voltage VIH INH 2.0 – – V LOW-level input voltage VIL INH – – 0.8 V – 10 IZ Q: Measurement cct 2, INH = LOW, VOH = VDD – Output leakage current Q: Measurement cct 2, INH = LOW, VOL = VSS – – 10 CF5009AN1 – 12 26 CF5009AN2 – 8 17 CF5009AN3 – 6 13 CF5009AN4 – 5 11 CF5009AN5 – 5 10 CF5009AN6 – 4 9 SM5009AN1S – 12 26 SM5009AN2S – 8 17 SM5009AN3S – 6 13 SM5009AN4S – 5 11 SM5009AN5S – 5 10 SM5009AN6S – 4 9 SM5009CN1S, CF5009CN1 – 10 22 SM5009CN2S, CF5009CN2 – 7 15 INH = open, Measurement cct 3, load cct 2, CL = 15pF, 40MHz crystal oscillator Current consumption IDD INH = open, Measurement cct 3, load cct 2, CL = 15pF, 40MHz crystal oscillator, Ta = –20 to +80°C INH = open, Measurement cct 3, load cct 2, CL = 15pF, 30MHz crystal oscillator µA mA INH pull-up resistance RUP Measurement cct 4, VDD = 5V, INH = VSS 40 – 200 kΩ Negative resistance −RL VDD = 5V, Ta = 25°C, 40MHz – –210 – Ω Feedback resistance Rf 0.4 – 1.1 MΩ 5.58 6 6.42 pF 9.3 10 10.7 pF Built-in capacitance CG CD Measurement cct 5 Design value. A monitor pattern on a wafer is tested. NIPPON PRECISION CIRCUITS INC.—9 SM5009 series 5009AK× series VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to 85°C unless otherwise noted. Rating Parameter Symbol Condition Unit min typ max HIGH-level output voltage VOH Q: Measurement cct 1, IOH = 16mA 4.0 – – V LOW-level output voltage VOL Q: Measurement cct 1, IOL = 16mA – – 0.4 V HIGH-level input voltage VIH INH 2.0 – – V LOW-level input voltage VIL INH – – 0.8 V – 10 IZ Q: Measurement cct 2, INH = LOW, VOH = VDD – Output leakage current Q: Measurement cct 2, INH = LOW, VOL = VSS – – 10 SM5009AK1S – 12 26 CF5009AK1 – 12 26 SM5009AK2S – 8 17 CF5009AK2 – 8 17 Current consumption IDD INH = open, Measurement cct 3, load cct 1, CL = 15pF, 40MHz crystal oscillator, Ta = –20 to +80°C µA mA INH pull-up resistance RUP Measurement cct 4, VDD = 5V, INH = VSS 40 – 200 kΩ Negative resistance −RL VDD = 5V, Ta = 25°C, 40MHz – –210 – Ω Feedback resistance Rf 0.4 – 1.1 MΩ 5.58 6 6.42 pF 9.3 10 10.7 pF Built-in capacitance CG CD Measurement cct 5 Design value. A monitor pattern on a wafer is tested. NIPPON PRECISION CIRCUITS INC.—10 SM5009 series 5009AH× series 3V operation: VDD = 2.7 to 3.3V, VSS = 0V, Ta = −20 to 80°C unless otherwise noted. Rating Parameter Symbol Condition Unit min typ max HIGH-level output voltage VOH Q: Measurement cct 1, IOH = 2mA 2.2 – – V LOW-level output voltage VOL Q: Measurement cct 1, IOL = 2mA – – 0.4 V HIGH-level input voltage VIH INH 2.0 – – V LOW-level input voltage VIL INH – – 0.3 V – 10 IZ Q: Measurement cct 2, INH = LOW, VOH = VDD – Output leakage current Q: Measurement cct 2, INH = LOW, VOL = VSS – – 10 SM5009AH1S CF5009AH1 – 4.5 10 SM5009AH2S CF5009AH2 – 3 7 SM5009AH3S CF5009AH3 SM5009AH4S CF5009AH4 – 1.5 3.5 Current consumption IDD INH = open, Measurement cct 3, load cct 2, CL = 15pF, 16MHz crystal oscillator µA mA INH pull-up resistance RUP Measurement cct 4, VDD = 3V, INH = VSS 40 – 200 kΩ Negative resistance −RL VDD = 3V, Ta = 25°C, 16MHz – –450 – Ω Feedback resistance Rf 0.4 – 1.1 MΩ 5.58 6 6.42 pF 9.3 10 10.7 pF Built-in capacitance CG Measurement cct 5 Design value. A monitor pattern on a wafer is tested. CD 5V operation: VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to 85°C unless otherwise noted. Rating Parameter Symbol Condition Unit min typ max HIGH-level output voltage VOH Q: Measurement cct 1, IOH = 4mA 4.0 – – V LOW-level output voltage VOL Q: Measurement cct 1, IOL = 4mA – – 0.4 V HIGH-level input voltage VIH INH 2.0 – – V LOW-level input voltage VIL INH – – 0.8 V – 10 IZ Q: Measurement cct 2, INH = LOW, VOH = VDD – Output leakage current Q: Measurement cct 2, INH = LOW, VOL = VSS – – 10 SM5009AH1S CF5009AH1 – 9 20 SM5009AH2S CF5009AH2 – 6 13 SM5009AH3S CF5009AH3 SM5009AH4S CF5009AH4 – 4 9 Current consumption IDD INH = open, Measurement cct 3, load cct 2, CL = 15pF, 30MHz crystal oscillator µA mA INH pull-up resistance RUP Measurement cct 4, VDD = 5V, INH = VSS 40 – 200 kΩ Negative resistance −RL VDD = 5V, Ta = 25°C, 30MHz – –340 – Ω Feedback resistance Built-in capacitance Rf CG CD Measurement cct 5 0.4 – 1.1 MΩ 5.58 6 6.42 pF 9.3 10 10.7 pF Design value. A monitor pattern on a wafer is tested. NIPPON PRECISION CIRCUITS INC.—11 SM5009 series Switching Characteristics 5009AL× series 3V operation: VDD = 2.7 to 3.3V, VSS = 0V, Ta = −40 to 85°C unless otherwise noted. Rating Parameter Symbol tr1 Output rise time tr2 tr3 tf1 Output fall time tf2 tf3 Duty1 Output duty cycle1 Duty2 Output disable delay time2 tPLZ Output enable delay time2 tPZL Condition Unit min typ max Measurement cct 3, load cct 2, 0.1VDD to 0.9VDD , CL = 15pF – 3.5 9 Measurement cct 3, load cct 2, 0.1VDD to 0.9VDD , VDD = 2.3 to 2.7V, Ta = –20 to +80°C, CL = 15pF – 4 13 Measurement cct 3, load cct 2, 0.1VDD to 0.9VDD , CL = 30pF – 5 12 Measurement cct 3, load cct 2, 0.1VDD to 0.9VDD , VDD = 2.4 to 2.7V, Ta = –20 to +80°C, CL = 30pF – 5.5 16 Measurement cct 3, load cct 2, 0.1VDD to 0.9VDD , VDD = 3.0 to 3.6V, f ≤ 30MHz, CL = 50pF – 5 12 Measurement cct 3, load cct 2, 0.2VDD to 0.8VDD , VDD = 3.0 to 3.6V, f ≤ 40MHz, CL = 50pF – 3.5 12 Measurement cct 3, load cct 2, 0.9VDD to 0.1VDD , CL = 15pF – 3.5 9 Measurement cct 3, load cct 2, 0.9VDD to 0.1VDD , VDD = 2.3 to 2.7V, Ta = –20 to +80°C, CL = 15pF – 4 13 Measurement cct 3, load cct 2, 0.9VDD to 0.1VDD , CL = 30pF – 5 12 Measurement cct 3, load cct 2, 0.9VDD to 0.1VDD , VDD = 2.4 to 2.7V, Ta = –20 to +80°C, CL = 30pF – 5.5 16 Measurement cct 3, load cct 2, 0.9VDD to 0.1VDD , VDD = 3.0 to 3.6V, f ≤ 30MHz, CL = 50pF – 5 12 Measurement cct 3, load cct 2, 0.8VDD to 0.2VDD , VDD = 3.0 to 3.6V, f ≤ 40MHz, CL = 50pF – 3.5 12 Measurement cct 3, load cct 2, VDD = 3V, f ≤ 40MHz, Ta = 25°C, CL = 30pF 45 – 55 Measurement cct 3, load cct 2, VDD = 2.4V, f ≤ 14.4MHz, Ta = 25°C, CL = 30pF 40 – 60 CF5009AL× only, Measurement cct 3, load cct 2, VDD = 2.5V, f ≤ 30MHz, Ta = 25°C, CL = 15pF 40 – 60 CF5009AL× only, Measurement cct 3, load cct 2, VDD = 3.3V, f ≤ 30MHz, Ta = 25°C, CL = 50pF 45 – 55 CF5009AL× only, Measurement cct 3, load cct 2, VDD = 3.3V, f ≤ 40MHz, Ta = 25°C, CL = 50pF 40 – 60 – – 100 ns – – 100 ns CF5009AL× 40 – – SM5009AL×S 30 – – SM5009AL×S 40 – – VDD = 2.4 to 2.7V, SM5009AL×S 14.4 – – VDD = 2.3 to 2.7V, CF5009AL× 30 – – VDD = 2.25 to 2.75V, CF5009AL× 20 – – Measurement cct 6, load cct 2, VDD = 3V, Ta = 25°C, CL ≤ 15pF ns ns % Measurement cct 3 Measurement cct 3, Ta = –20 to +80°C Maximum operating frequency fmax Measurement cct 3, Ta = –20 to +80°C MHz 1. The duty cycle characteristic is checked the sample chips of each production lot. 2. Oscillator stop function is built-in. When INH goes LOW, normal output stops. When INH goes HIGH, normal output is not resumed until after the oscillator start-up time has elapsed. NIPPON PRECISION CIRCUITS INC.—12 SM5009 series 5V operation: VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to 85°C unless otherwise noted. Rating Parameter Symbol Condition tr1 Output rise time tr2 Measurement cct 3, load cct 2, 0.1VDD to 0.9VDD tr3 tf1 Output fall time tf2 Measurement cct 3, load cct 2, 0.9VDD to 0.1VDD tf3 Output duty cycle1 Duty Output disable delay time2 tPLZ Output enable delay time2 tPZL Maximum operating frequency Unit min typ max CL = 15pF – 2 4 CL = 30pF – 3.5 7 CL = 50pF – 4 8 CL = 15pF – 2 4 CL = 30pF – 3.5 7 CL = 50pF – 4 8 45 – 55 % – – 100 ns – – 100 ns CF5009AL× 40 – – SM5009AL×S 30 – – SM5009AL×S 40 – – Measurement cct 3, load cct 2, VDD = 5V, Ta = 25°C, CL = 50pF Measurement cct 6, load cct 2, VDD = 5V, Ta = 25°C, CL ≤ 15pF ns ns Measurement cct 3 fmax Measurement cct 3, Ta = –20 to +80°C MHz 1. The duty cycle characteristic is checked the sample chips of each production lot. 2. Oscillator stop function is built-in. When INH goes LOW, normal output stops. When INH goes HIGH, normal output is not resumed until after the oscillator start-up time has elapsed. NIPPON PRECISION CIRCUITS INC.—13 SM5009 series 5009AN×/CN× series 3V operation: VDD = 2.7 to 3.3V, VSS = 0V, Ta = −20 to 80°C unless otherwise noted. Rating Parameter Symbol tr1 Condition Measurement cct 3, load cct 2, 0.1VDD to 0.9VDD ,CL = 15pF Unit min typ max SM5009AN1S, CF5009AN1 SM5009AN2S, CF5009AN2 – 3.5 9 SM5009AN3S, CF5009AN3 SM5009AN4S, CF5009AN4 SM5009AN5S, CF5009AN5 SM5009AN6S, CF5009AN6 SM5009CN1S, CF5009CN1 SM5009CN2S, CF5009CN2 – 5 13 SM5009AN1S, CF5009AN1 SM5009AN2S, CF5009AN2 – 5 12 SM5009AN3S, CF5009AN3 SM5009AN4S, CF5009AN4 SM5009AN5S, CF5009AN5 SM5009AN6S, CF5009AN6 SM5009CN1S, CF5009CN1 SM5009CN2S, CF5009CN2 – 7 16 SM5009AN1S, CF5009AN1 SM5009AN2S, CF5009AN2 – 3.5 9 SM5009AN3S, CF5009AN3 SM5009AN4S, CF5009AN4 SM5009AN5S, CF5009AN5 SM5009AN6S, CF5009AN6 SM5009CN1S, CF5009CN1 SM5009CN2S, CF5009CN2 – 5 13 SM5009AN1S, CF5009AN1 SM5009AN2S, CF5009AN2 – 5 12 SM5009AN3S, CF5009AN3 SM5009AN4S, CF5009AN4 SM5009AN5S, CF5009AN5 SM5009AN6S, CF5009AN6 SM5009CN1S, CF5009CN1 SM5009CN2S, CF5009CN2 – 7 16 CL = 30 pF, SM5009AN×S, CF5009AN× 45 – 55 CL = 15 pF, SM5009CN×S, CF5009CN× 40 – 60 – – 100 ns – – 100 ns SM5009AN×S, CF5009AN× 40 – – Ta = –10 to +70°C, SM5009CN×S, CF5009CN× 30 – – Output rise time ns tr2 tf1 Measurement cct 3, load cct 2, 0.1VDD to 0.9VDD ,CL = 30pF Measurement cct 3, load cct 2, 0.9VDD to 0.1VDD ,CL = 15pF ns Output fall time tf2 Output duty cycle1 Duty Output disable delay time tPLZ Output enable delay time tPZL Maximum operating frequency fmax Measurement cct 3, load cct 2, 0.9VDD to 0.1VDD ,CL = 30pF Measurement cct 3, load cct 2, VDD = 3V, Ta = 25°C % Measurement cct 6, load cct 2, VDD = 3V, Ta = 25°C, CL ≤ 15pF Measurement cct 3 MHz 1. The duty cycle characteristic is checked the sample chips of each production lot. NIPPON PRECISION CIRCUITS INC.—14 SM5009 series 5V operation: VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to 85°C unless otherwise noted. Rating Parameter Symbol Condition tr1 Output rise time tr2 Measurement cct 3, load cct 2, 0.1VDD to 0.9VDD tr3 tf1 Output fall time tf2 Measurement cct 3, load cct 2, 0.9VDD to 0.1VDD tf3 Output duty cycle1 Duty Output disable delay time tPLZ Output enable delay time tPZL Maximum operating frequency fmax Unit min typ max CL = 15pF – 2 4 CL = 30pF – 3.5 7 CL = 50pF – 4 8 CL = 15pF – 2 4 CL = 30pF – 3.5 7 CL = 50pF – 4 8 45 – 55 % – – 100 ns – – 100 ns SM5009AN×S, CF5009AN× 40 – – SM5009CN×S, CF5009CN× 30 – – Measurement cct 3, load cct 2, VDD = 5V, Ta = 25°C, CL = 50pF Measurement cct 6, load cct 2, VDD = 5V, Ta = 25°C, CL ≤ 15pF Measurement cct 3 ns ns MHz 1. The duty cycle characteristic is checked the sample chips of each production lot. 5009AK× series VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to 85°C unless otherwise noted. Rating Parameter Symbol Condition Unit min typ max Output rise time tr Measurement cct 3, load cct 1, 0.4V to 2.4V, CL = 15pF – 2 6 ns Output fall time tf Measurement cct 3, load cct 1, 2.4V to 0.4V, CL = 15pF – 2 6 ns Measurement cct 3, load cct 1, VDD = 5V, Ta = 25°C, CL = 15pF 45 – 55 % – – 100 ns – – 100 ns Ta = –20 to +80°C 40 – – Ta = –40 to +85°C 30 – – Output duty cycle1 Duty Output disable delay time tPLZ Output enable delay time tPZL Maximum operating frequency fmax Measurement cct 6, load cct 1, VDD = 5V, Ta = 25°C, CL ≤ 15pF Measurement cct 3 MHz 1. The duty cycle characteristic is checked the sample chips of each production lot. NIPPON PRECISION CIRCUITS INC.—15 SM5009 series 5009AH× series 3V operation: VDD = 2.7 to 3.3V, VSS = 0V, Ta = −20 to 80°C unless otherwise noted. Rating Parameter Symbol Condition Unit min typ max Output rise time tr1 Measurement cct 3, load cct 2, 0.1VDD to 0.9VDD , CL = 15pF – 6 18 ns Output fall time tf1 Measurement cct 3, load cct 2, 0.9VDD to 0.1VDD , CL = 15pF – 6 18 ns Measurement cct 3, load cct 2, VDD = 3V, Ta = 25°C, CL = 15pF 45 – 55 % – – 100 ns – – 100 ns 16 – – MHz Output duty cycle1 Duty Output disable delay time tPLZ Output enable delay time tPZL Maximum operating frequency fmax Measurement cct 6, load cct 2, VDD = 3V, Ta = 25°C, CL ≤ 15pF Measurement cct 3 1. The duty cycle characteristic is checked the sample chips of each production lot. 5V operation: VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to 85°C unless otherwise noted. Rating Parameter Symbol Condition Unit min typ max Output rise time tr1 Measurement cct 3, load cct 2, 0.1VDD to 0.9VDD , CL = 15pF – 4 12 ns Output fall time tf1 Measurement cct 3, load cct 2, 0.9VDD to 0.1VDD , CL = 15pF – 4 12 ns Measurement cct 3, load cct 2, VDD = 5V, Ta = 25°C, CL = 15pF 45 – 55 % – – 100 ns – – 100 ns 30 – – MHz Output duty cycle1 Duty Output disable delay time tPLZ Output enable delay time tPZL Maximum operating frequency fmax Measurement cct 6, load cct 2, VDD = 5V, Ta = 25°C, CL ≤ 15pF Measurement cct 3 1. The duty cycle characteristic is checked the sample chips of each production lot. NIPPON PRECISION CIRCUITS INC.—16 SM5009 series MEASUREMENT CIRCUITS Measurement cct 1 Measurement cct 4 3.0V or 5.0V When measuring VOL VDD R3 VDD Signal Generator XT RUP = RUP1 Q R1 VSS When measuring VOH VDD XT input waveform (10MHz) 0V Q output VDD VOH 0V Q output VDD VOL 0V • 5009AK×, AL×, AN1, AN2 R1: 50Ω R2: 250Ω(VDD = 4.5V), 275Ω(VDD = 2.7V) R3: 256Ω(VDD = 4.5V), 288Ω(VDD = 2.7V) • 5009AN3 to AN6, CN× R1: 50Ω R2: 245Ω(VDD = 4.5V), 262Ω(VDD = 2.7V) R3: 256Ω(VDD = 4.5V), 288Ω(VDD = 2.7V) • 5009AH× R1: 50Ω R2: 1000Ω(VDD = 4.5V), 1100Ω(VDD = 2.7V) R3: 1025Ω(VDD = 4.5V), 1150Ω(VDD = 2.7V) R2 INH VSS V VIH VIL A VDD IPR (VIL = 0V) RUP2 = VDD VIH IPR VIH : 2.1V(V DD = 3.0V) VIH : 3.5V(V DD = 5.0V) IPR Measurement cct 5 VDD XT VDD IRf Rf = XT Measurement cct 2 VSS A IRf IZ VDD IZ A Q Measurement cct 6 VSS V VOH VOL VDD Signal Generator Measurement cct 3 R1 INH VDD X'tal Q XT VSS IDD IST A XT Q XT INH R1: 50Ω VSS NIPPON PRECISION CIRCUITS INC.—17 SM5009 series Load cct 1 Load cct 2 Q output R CL Q output (Including probe capacitance) CL (Including probe capacitance) CL = 15pF: DUTY, IDD, tr, tf R = 400Ω CL = 15pF: DUTY, IDD, tr1, tf1 CL = 30pF: tr2, tf2 CL = 50pF: tr3, tf3 Switching Time Measurement Waveform Output duty level (CMOS) 0.9VDD Q output 0.9VDD 0.1VDD 0.1VDD DUTY measurement voltage (0.5V DD ) TW tr tf Output duty level (TTL) Q output 2.4V 2.4V 0.4V 0.4V DUTY measurement voltage (1.4V ) TW tr tf Output duty cycle (CMOS) DUTY measurement voltage (0.5V DD) Q output TW T DUTY= TW/ T 100 (%) Output duty cycle (TTL) DUTY measurement voltage (1.4V ) Q output TW T DUTY= TW/ T 100 (%) NIPPON PRECISION CIRCUITS INC.—18 SM5009 series Output Enable/Disable Delay INH VIH VIL tPZL tPLZ Q output INH input waveform tr = tf 10ns Note (AL× series only): when the device is in standby, the oscillator stops. When standby is released, the oscillator starts and stable oscillator output occurs after a short delay. NIPPON PRECISION CIRCUITS INC.—19 SM5009 series Please pay your attention to the following points at time of using the products shown in this document. The products shown in this document (hereinafter “Products”) are not intended to be used for the apparatus that exerts harmful influence on human lives due to the defects, failure or malfunction of the Products. Customers are requested to obtain prior written agreement for such use from NIPPON PRECISION CIRCUITS INC. (hereinafter “NPC”). Customers shall be solely responsible for, and indemnify and hold NPC free and harmless from, any and all claims, damages, losses, expenses or lawsuits, due to such use without such agreement. NPC reserves the right to change the specifications of the Products in order to improve the characteristic or reliability thereof. NPC makes no claim or warranty that the contents described in this document dose not infringe any intellectual property right or other similar right owned by third parties. Therefore, NPC shall not be responsible for such problems, even if the use is in accordance with the descriptions provided in this document. Any descriptions including applications, circuits, and the parameters of the Products in this document are for reference to use the Products, and shall not be guaranteed free from defect, inapplicability to the design for the mass-production products without further testing or modification. Customers are requested not to export or re-export, directly or indirectly, the Products to any country or any entity not in compliance with or in violation of the national export administration laws, treaties, orders and regulations. Customers are requested appropriately take steps to obtain required permissions or approvals from appropriate government agencies. NIPPON PRECISION CIRCUITS INC. 4-3, Fukuzumi 2-chome, Koto-ku, Tokyo 135-8430, Japan Telephone: +81-3-3642-6661 Facsimile: +81-3-3642-6698 http://www.npc.co.jp/ Email: [email protected] NC9801GE 2003.07 NIPPON PRECISION CIRCUITS INC.—20