NTE3047 Optoisolator TRIAC Driver Output Description: The NTE3047 optoisolator consists of a gallium arsenide infrared emitting diode, optically coupled to a silicon bilateral switch and is designed for applications requiring isolated TRIAC triggering, low current isolated AC switching, high electrical isolation (to 7500V peak), high detector standoff voltage, small size, and low cost. Applications: D Solenoid/Valve Controls D Lamp Ballasts D Motor Controls D Static AC Power Switch D Solid State Relays D Incandescent lamp Dimmers D Interfacing Microprocessors to 115VAC Preipherals Absolute Maximum Ratings: (TA = +25°C unless otherwise specified) Infrared Emitting Diode Reverse Voltage, VR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3V Continuous Forward Current, IF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60mA Total Power Dissipation (TA = +25°C, Negligible Power in Transistor), PD . . . . . . . . . . . . . . . 100mW Derate Above 25°C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.33mW/°C Output Driver Off–State Output Terminal Voltage, VDRM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250V Peak Repetitive Surge Current (PW = 1ms, 120pps), ITSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1A Total Power Dissipation (TA = +25°C), PD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300mW Derate Above 25°C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4mW/°C Total Device Isolation Surge Voltage (Peak AC Voltage, 60Hz, 5sec Duration, Note 1), VISO . . . . . . . . 7500VAC Total Power Dissipation (TA = +25°C), PD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330mW Derate Above 25°C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4mW/°C Junction Temperature Range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40° to +100°C Operating Ambient Temperature Range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40° to +85°C Storage Temperature Range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40° to +150°C Lead Temperature (During Soldering, 10s), TL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +260°C Note 1. Isolation surge voltage, VISO, is an internal device dielectric breakdown rating. For this test, Pin1 and Pin2 are common, and Pin4, Pin5, and Pin6 are common. Electrical Characteristics: (TA = +25°C unless otherwise specified) Parameter Symbol Test Conditions Min Typ Max Unit Input LED Reverse Leakage Current IR VR = 3V – 0.05 100 µA Forward Voltage VF IF = 10mA – 1.15 1.5 V Output Detector (IF = 0 unless otherwise specified) Peak Blocking Current, Either Direction IDRM Rated VDRM, Note 2 – 10 100 nA Peak On–State Voltage, Either Direction VTM ITM = 100mA Peak – 1.8 3.0 V Critical Rate of Rise of Off–State Voltage dv/dt Note 3 – 10 – V/µs Main Terminal Voltage = 3V, Note 4 – 8 15 mA – 100 – µA Coupled LED Trigger Current, Current Required to Latch Output IFT Holding Current, Either Direction IH Note 2. Test voltage must be applied within dv/dt rating. Note 3. This is static dv/dt. Commutating dv/dt is a function of the load–driving thyristor(s) only. Note 4. This device is guaranteed to trigger at an IF value les than or equal to max. IFT. Therefore, recommended operating IF lies between max. IFT (15mA) and absolute max. IF (60mA). 6 5 .260 (6.6) Max 1 2 Anode 1 6 Main Terminal Cathode 2 TRIAC Driver 5 Substrate Do Not Connect N.C. 3 4 Main Terminal 4 3 .070 (1.78) Max .350 (8.89) Max .200 (5.08) Max .085 (2.16) Max .300 (7.62) .350 (8.89) Max .100 (2.54)