TI ADS1281IPWRG4

 AD
ADS1281
®
S1
28
1
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
High-Resolution Analog-to-Digital Converter
FEATURES
DESCRIPTION
1
• High Resolution:
– 130dB SNR (250SPS)
– 127dB SNR (500SPS)
• High Accuracy:
– THD: –122dB (typ), –115dB (max)
– INL: 0.6ppm
• Inherently Stable Modulator with Fast
Responding Over-Range Detection
• Flexible Digital Filter:
– Sinc + FIR + IIR (Selectable)
– Linear or Minimum Phase Response
– Programmable High-Pass Filter
– Selectable FIR Data Rates:
– 250SPS to 4kSPS
• Filter Bypass Option
• Low Power Consumption:
– Operating: 12mW
– Shutdown: 10µW
• Calibration Engine for Offset and
Gain Correction
• Synchronization Input
• Analog Supply:
– Unipolar (+5V) or Bipolar (±2.5V)
• Digital Supply: 1.8V to 3.3V
2
APPLICATIONS
•
•
•
Energy Exploration
Seismic Monitoring
High-Accuracy Instrumentation
AVDD VREFN
VREFP
The ADS1281 is an extremely high-performance,
single-chip
analog-to-digital
converter
(ADC)
designed for the demanding needs of energy
exploration and seismic monitoring environments.
The single-chip design promotes board area savings
for improvements in high-density applications.
The converter uses a fourth-order, inherently stable,
delta-sigma (ΔΣ) modulator that provides outstanding
noise and linearity performance. The modulator is
used either in conjunction with the on-chip digital
filter, or can be bypassed for use with
post-processing filters.
The digital filter consists of sinc and finite impulse
response (FIR) low-pass stages followed by an
infinite impulse response (IIR) high-pass filter (HPF)
stage. Selectable decimation provides data rates from
250 to 4000 samples per second (SPS). The FIR
low-pass stage provides both linear and minimum
phase response. The HPF features an adjustable
corner frequency. On-chip gain and offset scaling
registers support system calibration.
The synchronization input (SYNC) can be used to
synchronize the conversions of multiple ADS1281s.
The SYNC input also accepts a clock input for
continuous alignment of conversions from an external
source.
Together, the modulator and filter dissipate only
12mW. The ADS1281 is available in a compact
TSSOP-24 package and is fully specified from –40°C
to +85°C, with a maximum operating range to
+125°C.
DVDD
ADS1281
AINP
4th-Order
DS
Modulator
AINN
Programmable
Digital Filter
Calibration
CLK
Serial
Interface
SCLK
DOUT
DIN
DRDY
Control
SYNC
RESET
PWDN
Over-Range
Modulator Output
3
AVSS
DGND
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2007, Texas Instruments Incorporated
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ORDERING INFORMATION
For the most current package and ordering information see the Package Option Addendum at the end of this
document, or see the TI web site at www.ti.com.
ABSOLUTE MAXIMUM RATINGS (1)
Over operating free-air temperature range, unless otherwise noted.
ADS1281
UNIT
AVDD to AVSS
–0.3 to +5.5
V
AVSS to DGND
–2.8 to +0.3
V
DVDD to DGND
–0.3 to +3.9
V
100, momentary
mA
10, continuous
mA
AVSS – 0.3 to AVDD + 0.3
V
Input current
Input current
Analog input voltage
Digital input voltage to DGND
–0.3 to DVDD + 0.3
V
+150
°C
Operating temperature range
–40 to +125
°C
Storage temperature range
–60 to +150
°C
Maximum junction temperature
(1)
2
Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may
degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those specified is not implied.
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
ELECTRICAL CHARACTERISTICS
Limit specifications at –40°C to +85°C, typical specifications at +25°C, AVDD = +2.5V, AVSS = –2.5V, fCLK (1) = 4.096MHz, VREFP = +2.5V,
VREFN = –2.5V, DVDD = +3.3V, and fDATA = 1000SPS, unless otherwise noted.
ADS1281
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
ANALOG INPUTS
Full-scale input voltage
VIN = AINP – AINN
Absolute input range
AINP or AINN
±VREF/2
AVSS – 0.1
Differential input impedance
V
AVDD + 0.1
V
55
kΩ
AC PERFORMANCE
fDATA = 250SPS
130
fDATA = 500SPS
Signal-to-noise ratio (2)
SNR
fDATA = 1000SPS
127
120
fDATA = 2000SPS
118
THD
Spurious-free dynamic
range (3)
SFDR
dB
121
fDATA = 4000SPS
Total harmonic distortion
124
–122
VIN = 31.25Hz, –0.5dBFS
–115
dB
123
dB
DC PERFORMANCE
Resolution
No missing codes
Data rate
Integral nonlinearity (4)
fDATA
INL
31
FIR filter mode
250
Sinc filter mode
8,000
Differential input
Offset error
Offset error after calibration (6)
Shorted input
Offset drift
Gain error
128,000
SPS
0.0005
% FSR (5)
10
200
µV
1
µV
0.06
µV/°C
fCM = 60Hz
AVDD, AVSS
DVDD
fPS = 60Hz
0.3
%
0.0002
%
0.4
ppm/°C
105
120
dB
85
95
85
105
Gain drift
Common-mode rejection
SPS
0.00006
0.1
Gain error after calibration (6)
Power-supply rejection
Bits
4000
dB
FIR DIGITAL FILTER RESPONSE
Passband ripple
±0.003
0.375 × fDATA
Passband (–0.01dB)
Stop band attenuation (7)
dB
Hz
135
dB
Stop band
0.500 × fDATA
Hz
Bandwidth (–3dB)
0.413 × fDATA
Hz
Group delay
Settling time (latency)
High-pass filter corner
(1)
(2)
(3)
(4)
(5)
(6)
(7)
FIR filter, minimum phase
5/fDATA
FIR filter, linear phase
31/fDATA
FIR filter, minimum phase
10/fDATA
FIR filter, linear phase
62/fDATA
0.1
s
s
10
Hz
fCLK = system clock.
SNR = signal-to-noise ratio = 20 log (VRMS Full-Scale/VRMS Noise), VIN = 20mVDC.
Highest spurious component including harmonics.
Best-fit method.
FSR: Full-scale range = ±VREF/2.
Calibration accuracy is on the level of noise reduced by 4 (calibration averages 16 readings).
Input frequencies in the range of NfCLK/512 ± fDATA/2 (N = 1, 2, 3...) can mix with the modulator chopping clock. In these frequency
ranges intermodulation = 120dB, typ.
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
3
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
ELECTRICAL CHARACTERISTICS (continued)
Limit specifications at –40°C to +85°C, typical specifications at +25°C, AVDD = +2.5V, AVSS = –2.5V, fCLK = 4.096MHz, VREFP = +2.5V,
VREFN = –2.5V, DVDD = +3.3V, and fDATA = 1000SPS, unless otherwise noted.
ADS1281
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
0.5
5
(AVDD – AVSS)
+ 0.2
V
V
VOLTAGE REFERENCE INPUTS
Reference input voltage
VREF = VREFP – VREFN
Negative reference input
VREFN
AVSS – 0.1
VREFP – 0.5
Positive reference input
VREFP
VREFN + 0.5
AVDD + 0.1
Reference input impedance
85
V
kΩ
DIGITAL INPUT/OUTPUT
VIH
0.8 × DVDD
DVDD
V
VIL
DGND
0.2 × DVDD
V
0.8 × DVDD
VOH
IOH = 1mA
VOL
IOL = 1mA
0.2 × DVDD
V
0 < VDIGITAL IN < DVDD
±10
µA
4.096
MHz
Input leakage
Clock input
fCLK
V
1
POWER SUPPLY
AVSS
–2.6
0
V
AVDD
AVSS + 4.75
AVSS + 5.25
V
DVDD
1.65
3.6
V
AVDD, AVSS current
DVDD current
Power dissipation
(8)
4
Operating mode
2
3
| mA |
Standby mode
1
15
| µA |
Power-Down mode
1
15
| µA |
Operating mode
0.6
0.8
mA
Modulator mode
0.1
Standby mode
25
50
Power-Down mode (8)
1
15
µA
Operating mode
12
18
mW
Standby mode
90
250
µW
Power-Down mode
10
150
µW
mA
µA
CLK input stopped.
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
DEVICE INFORMATION
TSSOP-24
Top View
CLK
1
24
BYPAS
SCLK
2
23
DGND
DRDY
3
22
DVDD
DOUT
4
21
PINMODE
MOD/DIN
5
20
RESET
DGND
6
19
PWDN
PHS/MCLK
7
18
VREFP
DR1/M1
8
17
VREFN
DR0/M0
9
16
AVSS
HPF/SYNC
10
15
AVDD
MFLAG
11
14
AINN
DGND
12
13
AINP
ADS1281
TERMINAL FUNCTIONS
DESCRIPTION
NAME
NO.
FUNCTION
PIN MODE (PINMODE = 1)
CLK
1
Digital input
Master clock input
REGISTER MODE (PINMODE = 0)
Master clock input
SCLK
2
Digital input
SPI serial clock input
SPI serial clock input
DRDY
3
Digital output
Data ready output: read data on falling edge
Data ready output: read data on falling edge
DOUT
4
Digital output
SPI serial data output
SPI serial data output
DIN: SPI serial data input
MOD/DIN
5
Digital input
MOD: 0 = Digital filter mode
1 = Filter bypass (modulator output)
PHS/MCLK
7
Digital I/O
(MOD = 0) PHS:
0 = Linear phase filter, 1 = Minimum phase filter
(MOD = 1) MCLK: Modulator clock output
If in modulator mode:
MCLK: Modulator clock output
Otherwise, the pin is an unused input (must be tied).
DR1/M1
8
Digital I/O
(MOD = 0) DR1 = Data rate select input 1
(MOD = 1) M1 = Modulator data output 1
If in modulator mode:
M1: Modulator data output 1
Otherwise, the pin is an unused input (must be tied).
DR0/M0
9
Digital I/O
(MOD = 0) DR0 = Data rate select input 0
(MOD = 1) M0 = Modulator data output 0
If in modulator mode:
M0: Modulator data output 0
Otherwise, the pin is an unused input (must be tied).
HPF/SYNC
10
Digital input
(MOD = 0) HPF: 0 = High-pass filter off, 1 = HPF on
(MOD = 1) SYNC = Synchronize Input
SYNC: Synchronize input
MFLAG
11
Digital output
Modulator over-range flag:
0 = Normal, 1 = Modulator over-range
Modulator over-range flag:
0 = Normal, 1 = Modulator over-range
DGND
6, 12, 23
Digital ground
Digital ground, pin 12 is the key ground point
Digital ground, pin 12 is the key ground point
AINP
13
Analog input
Positive analog input
Positive analog input
AINN
14
Analog input
Negative analog input
Negative analog input
AVDD
15
Analog supply
Positive analog power supply
Positive analog power supply
AVSS
16
Analog supply
Negative analog power supply
Negative analog power supply
VREFN
17
Analog input
Negative reference input
Negative reference input
VREFP
18
Analog input
Positive reference input
Positive reference input
PWDN
19
Digital input
Power-down input, active low
Power-down input, active low
RESET
20
Digital input
Synchronize input
Reset input
PINMODE
21
Digital input
1 = Pin mode
0 = Register mode
DVDD
22
Digital supply
Digital power supply: +1.8V to +3.3V
Digital power supply: +1.8V to +3.3V
BYPAS
24
Capacitor bypass
Digital core bypass; 1µF bypass capacitor to GND
Digital core bypass; 1µF bypass capacitor to GND
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
5
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
TIMING DIAGRAM
tSCDL
tSCLK
tSPWH
SCLK
tDIST
tSPWL
tSCDL
DIN
tDIHD
tDOHD
DOUT
tDOPD
TIMING REQUIREMENTS
At TA = –40°C to +85°C and DVDD = 1.65V to 3.6V, unless otherwise noted.
PARAMETER DESCRIPTION
tSCLK
tSPWH,
(1)
(2)
6
MIN
MAX
UNITS
2
16
1/fCLK
SCLK pulse width, high and low (1)
0.8
10
1/fCLK
SCLK period
L
tDIST
DIN valid to SCLK rising edge: setup time
50
tDIHD
Valid DIN to SCLK rising edge: hold time
50
ns
tDOPD
SCLK falling edge to valid new DOUT: propagation delay (2)
tDOHD
SCLK falling edge to DOUT invalid: hold time
0
ns
tSCDL
Final SCLK rising edge of command to first SCLK rising edge for register read/write
data. (Also between consecutive commands.)
24
1/fCLK
ns
100
ns
Holding SCLK low for 64 DRDY falling edges resets the SPI interface.
Load on DOUT = 20pF || 100kΩ.
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
TYPICAL CHARACTERISTICS
At TA = +25°C, AVDD = +2.5V, AVSS = –2.5V, fCLK = 4.096MHz, VREFP = +2.5V, VREFN = –2.5V, DVDD = +3.3V, and
fDATA = 1000SPS, unless otherwise noted.
OUTPUT SPECTRUM
OUTPUT SPECTRUM
0
0
VIN = -0.5dBFS, 31.25Hz
THD = -121.8dB
-20
-40
Amplitude (dB)
-40
-60
-80
-100
-120
-60
-80
-100
-120
-140
-140
-160
-160
-180
-180
0
50
100 150 200 250 300 350 400 450
Frequency (Hz)
500
0
50
100 150 200 250 300 350 400 450
Frequency (Hz)
Figure 1.
OUTPUT SPECTRUM
OUTPUT SPECTRUM
0
0
Shorted Input
SNR = 124.1dB
-20
-40
Amplitude (dB)
-60
-80
-100
-120
-60
-80
-100
-120
-140
-140
-160
-160
-180
-180
0
50
100 150 200 250 300 350 400 450
Frequency (Hz)
500
0
50
100 150 200 250 300 350 400 450
Frequency (Hz)
Figure 3.
500
Figure 4.
THD vs INPUT FREQUENCY
SNR HISTOGRAM
14
-100
VIN = -0.5dBFS
12
-105
THD Limited by
Signal Generator
25 Units
Shorted Input
10
Occurences
-110
-115
8
6
-120
4
-125
2
125.00
124.75
124.50
124.25
100
124.00
90
123.75
80
123.00
40
50
60
70
Input Frequency (Hz)
122.75
30
122.50
20
122.25
10
122.00
0
-130
123.50
Amplitude (dB)
VIN = 20mVDC
SNR = 124.3dB
-20
-40
THD (dB)
500
Figure 2.
123.25
Amplitude (dB)
VIN = -20dBFS, 31.25Hz
THD = -120.1dB
-20
SNR (dB)
Figure 5.
Figure 6.
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
7
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, AVDD = +2.5V, AVSS = –2.5V, fCLK = 4.096MHz, VREFP = +2.5V, VREFN = –2.5V, DVDD = +3.3V, and
fDATA = 1000SPS, unless otherwise noted.
NOISE AND THD vs VREF
124
-117
123
-119
122
-121
THD (dB)
SNR (dB)
SNR: Shorted Input
Noise (mVRMS)
-115
6
-105
5
-110
4
-115
THD: VIN = 31.25Hz, -0.5dBFS
3
-120
2
THD (dB)
SNR AND THD vs TEMPERATURE
125
-125
Noise: Shorted Input
121
-123
1
-125
125
0
-130
THD: VIN = 31.25Hz, -0.5dBFS
120
-55
-35
5
-15
25
45
65
Temperature (°C)
85
105
1
2
3
4
5
6
VREF (V)
Figure 7.
Figure 8.
SNR AND THD vs fCLK
POWER-SUPPLY AND COMMON-MODE REJECTION
vs FREQUENCY
125
140
-105
CMR
120
SNR: Shorted Input
-110
121
-115
THD: VIN = 31.25Hz, -0.5dBFS
119
PSR and CMR (dB)
DVDD
123
THD (dB)
SNR (dB)
-135
0
-120
100
80
AVSS
AVDD
60
40
40
Data Rate = fCLK/4096
117
1.0
1.5
2.0
2.5
3.0
fCLK (MHz)
3.5
0
-125
4.5
4.0
10
100
1k
10k
100k
Power Supply and Common-Mode Frequency (Hz)
Figure 9.
1M
Figure 10.
LINEARITY ERROR vs INPUT LEVEL
INL AND POWER vs TEMPERATURE
3
16
4
Integral Nonlinearity = ±0.5ppm
Power
12
0
2
8
-1
4
1
INL
-2
-3
-2.5 -2.0 -1.5 -1.0 -0.5 0
0.5
Input Level (V)
1.0
1.5
2.0
2.5
0
-55
-35
Figure 11.
8
Power (mW)
3
1
INL (ppm)
Linearity Error (ppm)
2
-15
5
45
25
65
Temperature (°C)
85
105
0
125
Figure 12.
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, AVDD = +2.5V, AVSS = –2.5V, fCLK = 4.096MHz, VREFP = +2.5V, VREFN = –2.5V, DVDD = +3.3V, and
fDATA = 1000SPS, unless otherwise noted.
POWER vs fCLK
GAIN AND OFFSET vs TEMPERATURE
16
100
200
5 Units
Power (mW)
12
10
8
6
4
2
0
0
0.5
1.0
1.5
2.0
2.5
fCLK (MHz)
3.0
3.5
4.0
4.5
75
100
Gain Error
0
50
-100
25
0
-200
Offset
-300
Normalized Offset (mV)
Normalized Gain Error (ppm)
14
-25
-400
-55
-35
-15
Figure 13.
5
25
45
65
Temperature (°C)
85
105
-50
125
Figure 14.
OFFSET HISTOGRAM
GAIN ERROR HISTOGRAM
18
10
25 Units
25 Units
16
9
7
Occurences
Occurences
14
5
12
10
8
6
3
4
2
2
0
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
10
20
30
40
50
60
70
80
90
100
-0.50
-0.45
-0.40
-0.35
-0.30
-0.25
-0.20
-0.15
-0.10
-0.05
0
0.05
0.10
0.15
0.20
0.25
0.30
0.35
0.40
0.45
0.50
0
Offset (mV)
Gain Error (%)
Figure 15.
Figure 16.
OFFSET DRIFT HISTOGRAM
GAIN DRIFT HISTOGRAM
90
80
25 Units
Based on 20°C
Intervals Over the Range
-40°C to +85°C.
25 Units
Based on 20°C Intervals
Over the Range
-40°C to +85°C.
45
40
35
60
Occurences
Occurences
70
50
50
40
30
30
25
20
15
5
0
0
-2.0
-1.8
-1.6
-1.4
-1.2
-1.0
-0.8
-0.6
-0.4
-0.2
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
10
10
-1.0
-0.9
-0.8
-0.7
-0.6
-0.5
-0.4
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
20
Offset Drift (mV/°C)
Gain Drift (ppm/°C)
Figure 17.
Figure 18.
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
9
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
OVERVIEW
The ADS1281 is a high-performance analog-to-digital
converter (ADC) intended for energy exploration,
seismic monitoring, chromatography, and other
exacting applications. The converter provides 24- or
32-bit output data in data rates from 4000SPS to
250SPS.
Figure 19 shows the block diagram of the ADS1281.
The device features unipolar and bipolar analog
power supplies (AVDD and AVSS, respectively) for
input range flexibility and a digital supply accepting
1.8V to 3.3V. The analog supplies may be set to +5V
to accept unipolar signals (with input offset) or set
lower in the range of ±2.5V to accept true bipolar
input signals (ground referenced).
An internal low-dropout (LDO) regulator is used to
power the digital core from DVDD. The BYPAS pin is
the LDO output and requires a 0.1µF capacitor for
noise reduction (BYPAS should not be used to drive
external circuitry).
The inherently-stable, fourth-order, ΔΣ modulator
measures the differential input signal VIN = (AINP –
AINN)
against
the
differential
reference
VREF = (VREFP – VREFN). A digital output (MFLAG)
indicates that the modulator is in over-range resulting
from an input overdrive condition. The modulator
output is available directly on the MCLK, M0, and M1
output pins. The modulator connects to an on-chip
digital filter that provides the output code readings.
AVDD
VREFN
The PINMODE input pin determines the mode of the
device: Pin control or Register control. In Pin control
mode, the device is controlled by simple pin settings;
there are no registers to program. In Register control
mode, the device is controlled by register settings.
The functionality of several device pins depends on
the control mode selected (see the Pin and Register
Modes section).
The SYNC input resets the operation of both the
digital filter and the modulator, allowing synchronized
conversions of multiple ADS1281 devices to an
external event. The SYNC input supports a
continuously-toggled input mode that accepts an
external data frame clock locked to an integer of the
conversion rate.
CLK
4th-Order
DS
Modulator
AINN
Gain and offset registers scale the digital filter output
to produce the final code value. The scaling feature
can be used for calibration and sensor gain matching.
The output data are provided with either a 24-bit word
or a full 32-bit word, allowing full utilization of the
inherently high resolution.
VREFP
ADS1281
AINP
The digital filter is comprised of a variable decimation
rate, fifth-order sinc filter followed by a
decimate-by-32,
FIR
low-pass
filter
with
programmable phase, and then by an adjustable
high-pass filter for dc removal of the output reading.
The output of the digital filter can be taken from the
sinc, the FIR low-pass, or the IIR high-pass section.
BYPAS
+1.8V
(Digital Core)
Programmable
Digital Filter
DVDD
LDO
Calibration
DRDY
SCLK
MOD/DIN
DOUT
Serial
Interface
Over-Range
Detection
PINMODE
PWDN
Control
DR1/M1
DR0/M0
AVSS
PHS/MCLK
MFLAG
HPF/SYNC
RESET
DGND
Figure 19. ADS1281 Block Diagram
10
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
The RESET input resets the register settings
(Register mode) and also restarts the conversion
process.
The PWDN input sets the device into a micro-power
state. Note that register settings are not retained in
PWDN mode. Use the STANDBY command in its
place if it is desired to retain register settings (the
quiescent current in the Standby mode is slightly
higher).
Noise-immune Schmitt-trigger and clock-qualified
inputs (RESET and SYNC) provide increased
reliability in high-noise environments.
MODULATOR
The
high-performance
modulator
is
an
inherently-stable, fourth-order, ΔΣ, 2 + 2 pipelined
structure, as shown in Figure 20. It shifts the
quantization noise to a higher frequency (out of the
passband) where digital filtering can easily remove it.
The modulator can be filtered either by the on-chip
digital filter or by use of post-processing filters.
fCLK/4
Analog Input (VIN)
The serial interface is used to read conversion data,
in addition to reading from and writing to the
configuration registers.
PHS/MCLK
2nd-Order
DS
1st-Stage
DR0/M0
2nd-Order
DS
2nd-Stage
DR1/M1
NOISE PERFORMANCE
4th-Order Modulator
The ADS1281 offers outstanding noise performance
(SFDR). Table 1 summarizes the typical noise
performance.
Table 1. Noise Performance (Typical)(1)
DATA RATE
FILTER
–3dB BW (Hz)
SNR (dB)
250
FIR
103
130
500
FIR
206
127
1000
FIR
413
124
2000
FIR
826
121
4000
FIR
1652
118
(1) VIN = 20mVDC.
IDLE TONES
The ADS1281 modulator incorporates an internal
dither signal that randomizes the idle tone energy.
Low-level idle tones may still be present, typically
–137dB below full-scale. The low-level idle tones can
be shifted out of the passband with the application of
an external 20mV offset.
Figure 20. Fourth-Order Modulator
The modulator first stage converts the analog input
voltage into a pulse-code modulated (PCM) stream.
When the level of differential analog input (AINP –
AINN) is near one-half the level of the reference
voltage 1/2 × (VREFP – VREFN), the ‘1’ density of
the PCM data stream is at its highest. When the level
of the differential analog input is near zero, the PCM
‘0’ and ‘1’ densities are nearly equal. At the two
extremes of the analog input levels (+FS and –FS),
the ‘1’ density of the PCM streams are approximately
+90% and +10%, respectively.
The modulator second stage produces a '1' density
data stream designed to cancel the quantization
noise of the first stage. The data streams of the two
stages are then combined before input to the digital
filter stage, as shown in Equation 1.
Y[n] = 3M0[n - 2] - 6M0[n - 3] + 4M0[n - 4]
+ 9(M1[n] - 2M1[n - 1] + M1[n - 2])
ADC
The ADC block of the ADS1281 is composed of two
blocks: a high-accuracy modulator and a
programmable digital filter.
(1)
M0[n] represents the most recent first-stage output
while M0[n – 1] is the previous first-stage output.
When the modulator output is enabled, the digital
filter shuts down to save power.
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
11
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
The modulator is optimized for input signals within a
4kHz passband. As Figure 21 shows, the noise
shaping of the modulator results in a sharp increase
in noise above 6kHz. The modulator has a chopped
input structure that further reduces noise within the
passband. The noise is moved out of the passband
and appears at the chopping frequency (fCLK/512 =
8kHz). The component at 6.5kHz is the tone
frequency, shifted out of band by a 20mV external
input. The frequency of the tone is approximately
VIN/3 (in kHz).
0
1Hz Resolution
VIN = 20mVDC
-20
Amplitude (dB)
-40
-60
-80
-100
-120
-140
-160
-180
1
10
100
1k
10k
100k
Frequency (Hz)
Figure 21. Modulator Output Spectrum
MODULATOR OVER-RANGE
The ADS1281 modulator is inherently stable and,
therefore, has predictable recovery behavior that
results from an input overdrive condition. The
modulator does not exhibit self-resetting behavior,
which often results in an unstable output data stream.
The ADS1281 modulator outputs a 1s density data
stream at 90% duty cycle with the positive full-scale
input signal applied (10% duty cycle with the negative
full-scale signal). If the input is overdriven past 90%
modulation, but below 100% modulation (10% and
0% for negative overdrive, respectively), the
modulator remains stable and continues to output the
1s density data stream. The digital filter may or may
not clip the output codes to +FS or –FS, depending
on the duration of the overdrive. When the input is
returned to the normal range from a long duration
overdrive (worst case), the modulator returns
immediately to the normal range, but the group delay
of the digital filter delays the return of the conversion
result to within the linear range (31 readings for linear
phase FIR). 31 additional readings (62 total) are
required for completely settled data.
12
If the inputs are sufficiently overdriven to drive the
modulator to full duty cycle, all 1s or all 0s
(±110%FSR), the modulator enters a stable saturated
state. The digital output code may clip to +FS or –FS,
again depending on the duration. A small duration
overdrive may not always clip the output code. When
the input returns to the normal range, the modulator
requires up to 12 modulator clock cycles (fMOD) to exit
saturation and return to the linear region. The digital
filter requires an additional 62 conversion for fully
settled data (linear phase FIR).
In the extreme case of over-range, either input is
overdriven exceeding that either analog supply
voltage plus an internal ESD diode drop. The internal
ESD diodes begin to conduct and the signal on the
input is clipped. If the differential input signal range is
not exceeded, the modulator remains in linear
operation. If the differential input signal range is
exceeded, the modulator is saturated but stable, and
outputs all 1s or 0s. When the input overdrive is
removed, the diodes recovery quickly and the
ADS1281 recovers as normal. Note that the linear
input range is ±100mV beyond the analog supply
voltages; with input levels above this, use care to limit
the input current to 100mA peak transient and 10mA
continuous.
MODULATOR OVER-RANGE DETECTION
(MFLAG)
The ADS1281 has a fast-responding over-range
detection, indicating when the differential input
exceeds approximately 100% over-range. The
threshold tolerance is ±2.5%.The MFLAG output
asserts high when in an over-range condition. As
Figure 22 and Figure 23 illustrate, the absolute value
of the input is compared to 100% of range. The
output of the comparator is sampled at the rate of
fMOD/2, yielding the MFLAG output. The minimum
MFLAG pulse width is fMOD/2.
AINP
å
AINN
IABSI
P
100% FS
Threshold Tolerance: ±2.5% Typical
Q
MFLAG
fMOD/2
Figure 22. Modulator Over-Range Block Diagram
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
FILTR[1:0] = 00. Pins DR0/M0 and DR1/M1 then
become the modulator data outputs and the
PHS/MCLK becomes the modulator clock output.
When not in the modulator mode, these pins are
inputs and must not float.
+100%
(AINP - AINN)
0%
-100%
The modulator output is composed of three signals:
one output for the modulator clock (PHS/MCLK) and
two outputs for the modulator data (DR0/M0 and
DR1/M1). The modulator clock output rate is fMOD
(fCLK/4). The SYNC input resets the MODCLK phase,
as shown in Figure 24. The SYNC input is latched on
the rising edge of CLK. The MODCLK resets and the
next rising edge of MODCLK occurs five CLK periods
later.
MFLAG
Figure 23. Modulator Over-Range Flag Operation
MODULATOR OUTPUT MODE
The modulator digital stream output is available
directly, bypassing and disabling the internal digital
filter. The modulator output mode is activated in the
Pin mode by setting MOD/DIN = 1, and in Register
mode by setting the CONFIG0 register bits
tCSHD
1
2
The modulator output data are two bits wide, which
must be merged together before being filtered. Use
the time domain equation of Equation 1 to merge the
data outputs.
3
4
5
CLK
tCMD
SYNC
tSCSU
tSYMD
PHS/MCLK
(MCLK = CLK/4)
tMCM0, 1
DR0/M0
DR1/M1
Figure 24. Modulator Mode Timing
Modulator Output Timing for Figure 24
PARAMETER
tMCD0,
(1)
1
DESCRIPTION
MIN
TYP
MODCLK rising edge to M0, M1 valid propagation delay (1)
tCMD
CLK rising edge (after SYNC rising edge) to MODCLK rising edge
reset time
tCSHD
CLK to SYNC hold time to not latch on CLK edge
10
tSCSU
SYNC to CLK setup time to latch on CLK edge
10
tSYMD
SYNC to stable bit stream
MAX
UNIT
100
ns
5
1/fCLK
ns
ns
16
1/fMOD
Load on M0 and M1 = 20pF || 100kΩ.
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
13
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
Table 3. Digital Filter Selection, Pin Mode
DIGITAL FILTER
The digital filter receives the modulator output and
decimates the data stream. By adjusting the amount
of filtering, tradeoffs can be made between resolution
and data rate: filter more for higher resolution, filter
less for higher data rate.
The digital filter is comprised of three cascaded filter
stages: a variable-decimation, fifth-order sinc filter; a
fixed-decimation FIR, low-pass filter (LPF) with
selectable phase; and a programmable, first-order,
high-pass filter (HPF), as shown in Figure 25.
The output can be taken from one of the three filter
blocks, as shown in Figure 25. To implement the
digital filter completely off-chip, select the filter bypass
setting (modulator output). For partial filtering by the
ADS1281, select the sinc filter output. For complete
on-chip filtering, activate both the sinc and FIR
stages. The HPF can then be included to remove dc
and low frequencies from the data. Table 2 shows the
filter options in Register mode. Table 3 shows the
filter options in Pin mode.
MOD/DIN
PIN
HPF/SYNC
PIN
DIGITAL FILTERS SELECTED
1
X
Bypass; modulator output mode
0
0
Sinc + FIR
0
1
Sinc + FIR + HPF
(low-pass and high-pass)
Sinc Filter Stage (sinx/x)
The sinc filter is a variable decimation rate, fifth-order,
low-pass filter. Data are supplied to this section of the
filter from the modulator at the rate of fMOD (fCLK/4).
The sinc filter attenuates the high-frequency noise of
the modulator, then decimates the data stream into
parallel data. The decimation rate affects the overall
data rate of the converter; it is set by the DR[1:0] and
MODE selections, as shown in Table 4.
Equation 2 shows the scaled Z-domain transfer
function of the sinc filter.
N
Table 2. Digital Filter Selection, Register Mode
FILTR[1:0] BITS
DIGITAL FILTERS SELECTED
00
Bypass; modulator output mode
01
Sinc
10
Sinc + FIR
11
Sinc + FIR + HPF
(low-pass and high-pass)
H(Z) =
5
1-Z
-1
1-Z
(2)
3
Filter
MUX
From Modulator
FIR Filter
Decimate
by 32
Sinc Filter
Decimate by
8 to 128
Direct Modulator
Bit Stream
To Calibration Block
High-Pass
Filter
(IIR)
Figure 25. Digital Filter
Table 4. Sinc Filter Data Rates (CLK = 4.096MHz)
14
DR[1:0] PINS
DR[2:0] REGISTER
DECIMATION RATIO (N)
00
000
128
8,000
01
001
64
16,000
10
010
32
32,000
11
011
16
64,000
—
100
8
128,000
Submit Documentation Feedback
SINC DATA RATE (SPS)
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
The frequency domain transfer function of the sinc
filter is shown in Equation 3.
0
5
-0.5
N4p ´ f
sin
fCLK
-1.0
4pf
fCLK
N sin
(3)
where:
N = decimation ratio (see Table 4)
-1.5
-2.0
-2.5
The sinc filter has notches (or zeroes) that occur at
the output data rate and multiples thereof. At these
frequencies, the filter has zero gain. Figure 26 shows
the frequency response of the sinc filter and
Figure 27 shows the roll-off of the sinc filter.
0
-3.0
0
0.05
0.10
0.15
0.20
Normalized Frequency (fIN/fDATA)
Figure 27. Sinc Filter Roll-Off
FIR Stage
-20
-40
Gain (dB)
Gain (dB)
½H(f)½ =
-60
-80
-100
-120
-140
0
1
2
3
4
Normalized Frequency (fIN/fDATA)
5
The second stage of the ADS1281 digital filter is an
FIR low-pass filter. Data are supplied to this stage
from the sinc filter. The FIR stage is segmented into
four sub-stages, as shown in Figure 28. The first two
sub-stages are half-band filters with decimation ratios
of 2. The third sub-stage decimates by 4 and the
fourth sub-stage decimates by 2. The overall
decimation of the FIR stage is 32. Note that two
coefficient sets are used for the third and fourth
sections, depending on the phase selection. Table 23
in the Appendix section at the end of this document
lists the FIR stage coefficients. Table 5 lists the data
rates and overall decimation ratio of the FIR stage.
Figure 26. Sinc Filter Frequency Response
Table 5. FIR Filter Data Rates
DR[1:0] PINS
DR[2:0] REGISTER
DECIMATION RATIO (N)
FIR DATA RATE (SPS)
00
000
4096
250
01
001
2048
500
10
010
1024
1000
11
011
512
2000
—
100
256
4000
Sinc
Filter
FIR Stage 1
Decimate by 2
FIR Stage 2
Decimate by 2
FIR Stage 3
Decimate by 4
FIR Stage 4
Decimate by 2
Output
Coefficients
Linear
Minimum
PHASE Select
Figure 28. FIR Filter Sub-Stages
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
15
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
As shown in Figure 29, the FIR frequency response
provides a flat passband to 0.375 of the data rate
(±0.003dB passband ripple). Figure 30 shows the
transition from passband to stop band.
0.003
Magnitude (dB)
0.002
GROUP DELAY AND STEP RESPONSE
The FIR block is implemented as a multi-stage FIR
structure with selectable linear or minimum phase
response. The passband, transition band, and stop
band responses of the filters are nearly identical but
differ in the respective phase responses.
Linear Phase Response
0.001
0
-0.001
-0.002
-0.003
0
0.08
0.16
0.24
0.32
Normalized Input Frequency (fIN/fDATA)
0.40
Linear phase filters exhibit constant delay time versus
input frequency (that is, constant group delay). Linear
phase filters have the property that the time delay
from any instant of the input signal to the same
instant of the output data is constant and is
independent of the signal nature. This filter behavior
results in essentially zero phase error when analyzing
multi-tone signals. However, the group delay and
settling time of the linear phase filter are somewhat
larger than the minimum phase filter, as shown in
Figure 31.
Figure 29. FIR Passband Amplitude Response
(fDATA = 500Hz)
1.4
Minimum Phase Filter
0
1.0
-20
0.8
Step Size
Amplitude (dB)
1.2
-40
0.6
0.4
-60
0.2
Linear Phase Filter
-80
0
-100
-0.2
0
-120
-140
0.35
0.40
0.45
0.50
0.55
0.60
Normalized Input Frequency (fIN/fDATA)
0.65
5
10 15 20 25 30 35 40 45 50 55 60 65
Time Index (1/fDATA)
Figure 31. FIR Step Response
Figure 30. FIR Transition Band Response
Although not shown in Figure 30, the passband
response repeats at multiples of the modulator
frequency (NfMOD – f0 and NfMOD + f0, where N = 1, 2,
etc. and f0 = passband). These image frequencies, if
present in the signal and not externally filtered, fold
back (or alias) into the passband and cause errors.
Placing an anti-alias, low-pass filter in front of the
ADS1281 inputs is recommended to limit possible
out-of-band input signals. Often, a single RC filter is
sufficient.
16
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
Minimum Phase Response
The minimum phase filter provides a short delay from
the arrival of an input signal to the output, but the
relationship (phase) is not constant versus frequency,
as shown in Figure 32. The filter phase is selected by
the PHS bit (Register mode) or the PHS/MCLK pin
(Pin mode); Table 6 shows additional information.
Table 6. FIR Phase Selection
PHS BIT or
PHS/MCLK PIN
FILTER PHASE
0
Linear
1
Minimum
HPF[dec] = 65,536 1 -
cos wN
Where:
HPF = High-pass filter register value (converted
to hexidecimal)
ωN = 2πfHP/fDATA (normalized frequency,
radians)
fHP = High-pass corner frequency (Hz)
fDATA = Data rate (Hz)
Table 7. High-Pass Filter Value Examples(1)
Linear Phase Filter
30
Group Delay (1/fDATA)
cos wN + sin wN - 1
(6)
35
25
fHP (Hz)
DATA RATE (SPS)
HPF[1:0]
0.5
250
0337h
1.0
500
0337h
1.0
1000
019Ah
(1) In Pin Control mode the HPF value is fixed at 0332h.
20
The HPF causes a small gain error, in which case the
magnitude depends on the ratio of fHP/fDATA. For
many common values of (fHP/fDATA), the gain error is
negligible. Figure 33 shows the gain error of the HPF.
The gain error factor is illustrated in Equation 13 (see
the Appendix at the end of this document).
15
10
Minimum Phase Filter
5
0
20
40
60
80 100 120
Frequency (Hz)
140 160 180
200
0
Figure 32. FIR Group Delay (fDATA = 500Hz)
The last stage of the ADS1281 filter block is a
first-order HPF implemented as an IIR structure. This
filter stage blocks dc signals and rolls off
low-frequency components below the cut-off
frequency. The transfer function for the filter is shown
in Equation 4:
1 - Z-1
2-a
´
HPF(Z) =
-1
2
1 - bZ
(4)
Gain Error (dB)
-0.10
HPF Stage
-0.20
-0.30
-0.40
-0.50
0.0001
where b is calculated as shown in Equation 5:
(1 + (1 - a) )
2
0.001
0.01
0.1
Frequency Ratio (fHP/fDATA)
Figure 33. HPF Gain Error
2 2
b=
1-2
(5)
The high-pass corner frequency is programmed by
registers HPF[1:0], in hexidecimal. Equation 6 is used
to set the high-pass corner frequency. Table 7 lists
example values for the high-pass filter.
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
17
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
ANALOG INPUT CIRCUITRY (AINP, AINN)
The ADS1281 measures the differential input signal
VIN = (AINP – AINN) against the differential reference
VREF = (VREFP – VREFN) using internal capacitors
that are continuously charged and discharged.
Figure 36 shows the simplified schematic of the ADC
input circuitry; the right side of the figure illustrates
the input circuitry with the capacitors and switches
replaced by an equivalent circuit. Figure 35
demonstrates the ON/OFF timings for the switches of
Figure 36.
90
-7.5
75
-15.0
60
Amplitude
45
-22.5
Phase
-30.0
30
-37.5
15
-45.0
0.01
0
0.1
1
10
Normalized Frequency (f/fC)
100
Figure 34. HPF Amplitude and Phase Response
In Figure 36, S1 switches close during the input
sampling phase. With switch S1 closed, CA1 charges
to AINP, CA2 charges to AINN, and CB charges to
(AINP – AINN). For the discharge phase, S1 opens
first and then S2 closes. CA1 and CA2 discharge to
approximately to AVSS + 1.3V and CB discharges to
0V. This two-phase sample/discharge cycle repeats
with a period of tSAMPLE = 1/fMOD. fMOD is the operating
frequency of the modulator. See the Master Clock
Input (CLK) section.
AVDD
0
Phase (°)
Amplitude (dB)
Figure 34 shows the first-order amplitude and phase
response of the HPF. Note that in the case of
applying step inputs or synchronizing, the settling
time of the filter should be taken into account.
tSAMPLE = 1/fMOD
ON
S1
OFF
ON
S2
OFF
Figure 35. S1 and S2 Switch Timing for Figure 36
AVSS + 2.5V
AVSS + 2.5V
S2
REFF A = 325kW
CA1 = 3pF
S1
Equivalent
Circuit
AINP
AINP
REFF B = 61kW
CB = 16pF
(fMOD = 1.024MHz)
S1
AINN
AINN
REFF A = 325kW
CA2 = 3pF
S2
AVSS
AVSS + 2.5V
REFF =
1
fMOD ´ CX
AVSS + 2.5V
RAIN = REFF B || 2REFF A
Figure 36. Simplified ADC Input Structure
18
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
The charging of the input sampling capacitors draws
a transient current from the source driving the
ADS1281 ADC inputs. The average value of this
current can be used to calculate an effective
impedance (REFF) where REFF = VIN/IAVERAGE. These
impedances scale inversely with fMOD. For example, if
fMOD is reduced by a factor of two, the impedances
double.
ESD diodes protect the analog inputs. To keep these
diodes from turning on, make sure the voltages on
the input pins do not go below AVSS by more than
300mV, and likewise do not exceed AVDD by more
than 300mV, as shown in Equation 7.
AVDD
ESD
Diodes
VREFP
11.5pF
VREFN
ESD
Diodes
AVSS - 300mV < (AINP or AINN) < AVDD + 300mV
The ADS1281 is a very high-performance ADC. For
optimum performance, it is essential that the
ADS1281 inputs be driven with a buffer with noise
and distortion commensurate with the ADS1281
performance; see the Applications section. Most
applications require an external capacitor (COG/NPO
dielectric) directly across the input pins. Depending
on the input driver settling characteristics, some
experimentation may be necessary to optimize the
value to minimize THD (generally in the range of
2.2nF to 100nF). Best performance is achieved with
the common-mode signal centered at mid-supply.
Although optimized for differential signals, the
ADS1281 inputs may be driven with a single-ended
signal by fixing one input to mid-supply. To take
advantage of the full dynamic range, the driven input
must swing 5VPP for VREF = 5V.
VOLTAGE REFERENCE INPUTS
(VREFP, VREFN)
The voltage reference for the ADS1281 ADC is the
differential voltage between VREFP and VREFN:
VREF = VREFP – VREFN. The reference inputs use a
structure similar to that of the analog inputs with the
circuitry on the reference inputs shown in Figure 37.
The average load presented by the switched
capacitor reference input can be modeled with an
effective differential impedance of REFF = tSAMPLE/CIN
(tSAMPLE = 1/fMOD). Note that the effective impedance
of the reference inputs loads an external reference
with non-zero source impedance.
REFF =
1
fMOD ´ CX
AVSS
(7)
Some applications of the device may require external
clamp diodes and/or series resistors to limit the input
voltage to within this range.
REFF = 85kW
(fMOD = 1.024MHz)
Figure 37. Simplified Reference Input Circuit
The ADS1281 reference inputs are protected by ESD
diodes. In order to prevent these diodes from turning
on, the voltage on either input must stay within the
range shown in Equation 8:
AVSS - 300mV < (VREFP or VREFN) < AVDD + 300mV
(8)
A high-quality reference voltage is necessary for
achieving the best performance from the ADS1281.
Noise and drift on the reference degrade overall
system performance, and it is critical that special care
be given to the circuitry generating the reference
voltages in order to achieve full performance. For
most applications, a 1µF ceramic capacitor applied
directly to the reference inputs pins is suggested.
MASTER CLOCK INPUT (CLK)
The ADS1281 requires a clock input for operation.
The clock is applied to the CLK pin. The data
conversion rate scales directly with the CLK
frequency. Power consumption versus CLK frequency
is relatively constant (see the Typical Characteristics).
As with any high-speed data converter, a high-quality,
low-jitter clock is essential for optimum performance.
Crystal clock oscillators are the recommended clock
source. Make sure to avoid excess ringing on the
clock input; keep the clock trace as short as possible
and use a 50Ω series resistor close to the source.
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
19
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
PIN AND REGISTER MODES
The ADS1281 has two sources for synchronization:
the SYNC input pin and the SYNC command. The
ADS1281 also has two synchronizing modes:
Pulse-sync and Continuous-sync. In Pulse-sync
mode, the ADS1281 synchronizes to a single sync
event. In Continuous-sync mode, either the device
synchronizes to a single sync event or a continuous
clock is applied to the pin with a period equal to
integer multiples of the data rate. When the periods of
the sync input and the DRDY output do not match,
the ADS1281 re-synchronizes and conversions are
restarted. Note that in Pin control mode, the RESET
input serves as the SYNC control.
The PINMODE input (pin 21) is used to set the
control mode of the device: Pin mode or Register
mode. In Pin mode (PINMODE = 1), control of the
device is set by pins; there are no registers to
program. In Register mode, control of the device is
set by the configuration registers. As a result of the
increased flexibility provided by the register space,
Register mode has more control options. Table 8
describes the differences between the control modes.
Table 9 summarizes the functions of the dual-purpose
pins, depending on the control mode selected.
SYNCHRONIZATION
(SYNC PIN AND SYNC COMMAND)
The ADS1281 can be synchronized to an external
event, as well as synchronized to other ADS1281
devices if the sync event is applied simultaneously to
all devices.
Table 8. Functions for Pin Mode and Register Mode
FUNCTION
PIN MODE
(PINMODE = 1)
REGISTER MODE
(PINMODE = 0)
Synchronization options
Pulse only
Continuous or Pulse
Digital filter options
SINC + LPF or SINC + LPF + HPF
Sinc, Sinc + LPF, or Sinc + LPF + HPF
Digital high-pass filter frequency
Fixed low-cut as ratio of fDATA
Programmable
Calibration registers
No
Yes
Interface commands
No
Yes
Table 9. Mode-Dependent Pin Functions
20
PIN
PIN MODE
(PINMODE = 1)
REGISTER MODE
(PINMODE = 0)
MOD/DIN
MOD input (select Modulator mode)
SPI DIN input
HPF/SYNC
HPF input (select high-pass filter)
SYNC input
RESET
Sync input
Reset input
PHS/MCLK
LPF phase input or MCLK output
MCLK output
DR0/M0
DR0 input or M0 output
M0 output
DR1/M1
DR1 input or M1 output
M1 output
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
PULSE-SYNC MODE
tCSHD
In Pulse-sync mode, the ADS1281 stops and restarts
the conversion process when a sync event occurs (by
pin or command). When the sync event occurs, the
device resets the internal memory; DRDY goes high,
and after the digital filter has settled, new conversion
data are available, as shown in Figure 38 and
Table 10.
System Clock
(fCLK)
tSCSU
SYNC Command
(1)
tSPWH
SYNC Pin
New Data
Ready
tSPWL
tDR
DRDY
(Pulse-Sync)
CONTINUOUS-SYNC MODE
In Continuous-sync mode, either a single sync pulse
or a continuous clock may be applied. When a single
sync pulse is applied (rising edge), the device
behaves similar to the Pulse-sync mode. However, in
this mode, DRDY continues to toggle unaffected but
the DOUT output is held low until data are ready.
When the conversion data are non-zero, new
conversion data are ready (as shown in Figure 38).
When a continuous clock is applied to the SYNC pin,
the period must be an integral multiple of the output
data rate or the device re-synchronizes. When the
sync input is first applied on the first rising edge of
CLK, the device re-synchronizes (under the condition
tSYNC ≠ N/fDATA). DRDY continues to output but DOUT
is held low until the new data are ready. Then, if the
period of the applied sync clock matches an integral
multiple of the output data rate, the device freely runs
without re-synchronization. The phase of the applied
clock and output data rate (DRDY) do not have to
match. Figure 39 shows the
timing for
Continuous-sync mode.
1/fDATA
New Data
Ready
DRDY
(Continuous-Sync)
tDR
DOUT
(1) Command takes effect on the next rising CLK edge after the
eighth rising SCLK edge. In order for the SYNC command to be
effective for synchronization of multiple devices, the command
must be broadcast to devices simultaneously.
Figure 38. Pulse-Sync Timing, Continuous-Sync
Timing with Single Sync
tSCSU
tCSHD
System Clock
(fCLK)
tSPWL
tSPWH
SYNC
tSYNC
DRDY
1/fDATA
Figure 39. Continuous-Sync Timing with Sync
Clock
Table 10. Pulse-Sync Timing for Figure 38 and Figure 39
PARAMETER
DESCRIPTION
MIN
MAX
UNITS
tSYNC
Sync period (1)
1
Infinite
n/fDATA
tCSHD
CLK to SYNC hold time to not latch on CLK edge
10
tSCSU
SYNC to CLK setup time to latch on CLK edge
10
ns
SYNC pulse width, high or low
2
1/fCLK
tSPWH,
tDR
(1)
L
Time for data ready (SINC filter)
Time for data ready (FIR filter)
ns
See Appendix, Table 24
62.98046875/fDATA + 466/fCLK
Continuous-Sync mode; a free-running SYNC clock input without causing re-synchronization.
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
21
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
RESET (RESET Pin and Reset Command)
The ADS1281 may be reset in two ways: toggle the
RESET pin low or send a Reset command. When
using the RESET pin, take it low and hold for at least
2/fCLK to force a reset. The ADS1281 is held in reset
until the pin is released. By command, RESET takes
effect on the next rising edge of fCLK after the eighth
rising edge of SCLK of the command. Note: to ensure
that the Reset command can function, the SPI
interface may require a reset; see the Serial Interface
section.
In reset, registers are set to default and the
conversions are synchronized on the next rising edge
of CLK. New conversion data are available, as shown
in Figure 40 and Table 11.
Settled
Data
DRDY
tDR
tCRHD
Wakeup
Command
DRDY
tDR
Figure 41. PWDN Pin and Wake-Up Command
Timing
(Table 12 shows tDR)
The ADS1281 has three power supplies: AVDD,
AVSS, and DVDD. Figure 42 shows the power-on
sequence of the ADS1281. The power supplies can
be sequenced in any order. The supplies [the
difference of (AVDD – AVSS) and DVDD] generate
an internal reset whose outputs are summed to
generate a global internal reset. After the supplies
have crossed the minimum thresholds, 216 fCLK cycles
are counted before releasing the internal reset. After
the internal reset is released, new conversion data
are available, as shown in Figure 42 and Table 12.
tRCSU
RESET Pin
or
RESET Command
Figure 40. Reset Timing
Table 11. Reset Timing for Figure 40
PARAMETER DESCRIPTION
PWDN Pin
POWER-ON SEQUENCE
System Clock
(fCLK)
tRST
In power-down, note that the device outputs remain
active and the device inputs must not float. When the
Standby command is sent, the SPI port and the
configuration registers are kept active. Figure 41 and
Table 12 show the timing.
MIN
UNITS
tCRHD
CLK to RESET hold time
10
ns
tRGSU
RESET to CLK setup time
10
ns
tRST
RESET low
2
1/fCLK
tDR
Time for data ready
62.98046875/
fDATA + 468/fCLK
AVDD - AVSS
DVDD
3.5V nom
1V nom
CLK
16
POWER-DOWN
(PWDN Pin and Standby Command)
Internal Reset
There are two ways to power-down the ADS1281:
take the PWDN pin low or send a Standby command.
When the PWDN pin is pulled low, the internal
circuitry is disabled to minimize power and the
contents of the register settings are reset.
2
fCLK
DRDY
tDR
Figure 42. Power-On Sequence
Table 12. Power-On, PWDN Pin, and Wake-Up Command Timing for New Data
PARAMETER
DESCRIPTION
FILTER MODE
16
tDR
(1)
(2)
22
Time for data ready 2 CLK cycles after power-on;
and new data ready after PWDN pin or Wake-Up command
See Appendix, Table 24
SINC (1)
62.98046875/fDATA + 468/fCLK (2)
FIR
Supply power-on and PWDN pin default is 1000SPS FIR.
Subtract 2 CLK cycles for the Wake-Up command. The Wake-Up command is timed from the next rising edge of CLK to after the eighth
rising edge of SCLK during command to DRDY falling.
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
DVDD POWER SUPPLY
Serial Clock (SCLK)
The DVDD supply operates over the range of +1.65V
to +3.6V. If DVDD is operated at less than 2.25V,
connect the DVDD pin to the BYPAS pin. If DVDD is
greater than or equal to 2.25V, do not connect DVDD
to the BYPAS pin (open connection). Figure 43
shows this connection.
The serial clock (SCLK) is an input that is used to
clock data into (DIN) and out of (DOUT) the
ADS1281. This input is a Schmitt-trigger input that
has a high degree of noise immunity. However, it is
recommended to keep SCLK as clean as possible to
prevent possible glitches from inadvertently shifting
the data.
1.65V to 3.6V
Data are shifted into DIN on the rising edge of SCLK
and data are shifted out of DOUT on the falling edge
of SCLK. If SCLK is held low for 64 DRDY cycles,
data transfer or commands in progress terminate and
the SPI interface resets. The next SCLK pulse starts
a new communication cycle. This timeout feature can
be used to recover the interface when a transmission
is interrupted or SCLK inadvertently glitches. SCLK
should remain low when not active.
DVDD
ADS1281
Tie DVDD to BYPAS if
DVDD power is < 2.25V.
Otherwise float BYPAS.
BYPAS
1m F
Figure 43. DVDD Power
Data Input (DIN)
SERIAL INTERFACE
A serial interface is used to read the conversion data
and access the configuration registers. The interface
consists of three basic signals: SCLK, DIN, and
DOUT. An additional output, DRDY, transitions low in
Read Data Continuous mode when data are ready for
retrieval. Figure 44 shows the connection when
multiple converters are used.
FPGA or Processor
SCLK
SCLK
The data input pin (DIN) is used to input register data
and commands to the ADS1281. Keep DIN low when
reading conversion data in the Continuous Read Data
mode (except when issuing a STOP Read Data
Continuous command). Data on DIN are shifted into
the converter on the rising edge of SCLK. In Pin
mode, DIN is not used.
Data Output (DOUT)
The data output pin (DOUT) is used to output data
from the ADS1281. Data are shifted out on DOUT on
the falling edge of SCLK. In Pin mode, only
conversion data are read from this pin.
DOUT1
DOUT1
ADS1281
DIN2
DIN1
DRDY1
IRQ
SCLK
SCLK (optional)
DOUT2
DOUT2
ADS1281
DIN2
DIN2
DRDY2
IRQ (optional)
Figure 44. Pin Mode Interface for Multiple Devices
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
23
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
Data Ready (DRDY)
DATA FORMAT
DRDY is an output; when it transitions low, this
transition indicates new conversion data are ready, as
shown in Figure 45. When reading data by the
continuous mode, the data must be read within four
CLK periods before DRDY goes low again or the data
are overwritten with new conversion data. When
reading data by the command mode, the read
operation can overlap the occurrence of the next
DRDY without data corruption.
The ADS1281 provides 32 bits of conversion data in
binary twos complement format, as shown in
Table 13. The LSB of the data is a redundant sign bit:
'0' for positive numbers and '1' for negative numbers.
However, when the output is clipped to +FS, the
LSB = 1; when the output is clipped to –FS, the
LSB = 0. If desired, the data readback may be
stopped at 24 bits.
Table 13. Ideal Output Code versus Input Signal
INPUT SIGNAL VIN
(AINP – AINN)
DRDY
DOUT
Bit 31
Bit 30
VREF
>
Bit 29
32-BIT IDEAL OUTPUT
CODE(1)
7FFFFFFFh
2
VREF
SCLK
7FFFFFFEh
2
Figure 45. DRDY with Data Retrieval
DRDY resets high on the first falling edge of SCLK.
Figure 45 and Figure 46 show the function of DRDY
with and without data readback, respectively.
If data are not retrieved (no SCLK provided), DRDY
pulses high for four fCLK periods during the update
time, as shown in Figure 46.
VREF
0
00000000h
-VREF
FFFFFFFFh
2 ´ (230 - 1)
-VREF
2
4/fCLK
00000002h
2 ´ (230 - 1)
230
´
Data Updating
<
DRDY
-VREF
2
80000001h
230 - 1
230
´
80000000h
30
2 -1
(1) Excludes effects of noise, linearity, offset, and gain errors.
Figure 46. DRDY With No Data Retrieval
24
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
READING DATA
The ADS1281 has two ways to read conversion data:
Read Data Continuous and Read Data By Command.
Read Data Continuous
In the Read Data Continuous mode, the conversion
data are shifted out directly from the device without
the need for sending a read command. This mode is
the default mode at power-on. This mode is also
enabled by the RDATAC command. When DRDY
goes low, indicating that new data are available, the
MSB of data appears on DOUT, as shown in
Figure 47. The data are normally read on the rising
edge of SCLK and at the occurrence of the first falling
edge of SCLK, DRDY returns high. After 32 bits of
data have been shifted out, further SCLK transitions
cause DOUT to go low. If desired, the read operation
may be stopped at 24 bits. The data shift operation
must be completed within four CLK periods before
DRDY falls again or the data may be corrupted.
The Read Data Continuous mode is the default data
mode for Pin mode. When a Stop Read Data
Continuous command is issued, the DRDY output is
blocked but the ADS1281 continues conversions. In
stop continuous mode, the data can only be read by
command.
DRDY
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16
25 26 27 28 29 30
31 32
SCLK
DOUT
Data Byte 1 (MSB)
Data Byte 2 (MSB - 1)
Data Byte 4 (LSB)
tDDPD
DIN
Figure 47. Read Data Continuous
Table 14. Timing Data for Figure 47
PARAMETER
tDDPD
(1)
DESCRIPTION
MIN
DRDY to valid MSB on DOUT propagation delay (1)
TYP
MAX
UNITS
100
ns
Load on DOUT = 20pF || 100kΩ.
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
25
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
Read Data By Command
ONE-SHOT OPERATION
The Read Data Continuous mode is stopped by the
SDATAC command. In this mode, conversion data
are read by command. In the Read Data By
Command mode, a read data command must be sent
to the device for each data conversion (as shown in
Figure 48). When the read data command is received
(on the eighth SCLK rising edge), data are available
to read only when DRDY goes low (tDR). When DRDY
goes low, conversion data appear on DOUT. The
data may be read on the rising edge of SCLK.
The ADS1281 can perform very power-efficient,
one-shot conversions using the STANDBY command
while under software control. Figure 49 shows this
sequence. First, issue the STANDBY command to set
the Standby mode.
When ready to make a measurement, issue the
WAKEUP command. Monitor DRDY; when it goes
low, the fully setted conversion data are ready and
may be read directly in Read Data Continuous mode.
Afterwards, issue another STANDBY command.
When ready for the next measurement, repeat the
cycle starting with another WAKEUP command.
DRDY
tDR
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16
33 34 35 36 37 38
39 40
SCLK
DOUT
Don't Care
Data Byte 1 (MSB)
Date Byte 4 (LSB)
tDDPD
DIN
Command Byte (0001 0010)
Figure 48. Read Data By Command, RDATA (tDDPD timing is given in Table 14)
Table 15. Read Data Timing for Figure 48
PARAMETER
tDR
DESCRIPTION
MIN
Time for new data after data read command
ADS1281 Status
Standby
TYP
MAX
UNITS
1
fDATA
0
Performing One-Shot Conversion
Standby
DRDY
DIN
(1)
STANDBY
STANDBY
WAKEUP
Settled
Data
DOUT
(1) See Figure 41 and Table 12 for time to new data.
Figure 49. One-Shot Conversions Using the STANDBY Command
26
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
Table 16. Offset Calibration Values
OFFSET AND FULL-SCALE CALIBRATION
REGISTERS
The conversion data can be scaled for offset and gain
before yielding the final output code. As shown in
Figure 50, the output of the digital filter is first
subtracted by the offset register (OFC) and then
multiplied by the full-scale register (FSC). Equation 9
shows the scaling:
GANCAL
Final Output Data = (Input - OFSCAL) ´
400000h
(9)
The values of the offset and full-scale registers are
set by writing to them directly, or they are set
automatically by calibration commands.
OFC[2:0] Registers
The offset calibration is a 24-bit word, composed of
three 8-bit registers, as shown in Table 18. The offset
register is left-justified to align with the 32-bits of
conversion data. The offset is in twos complement
format with a maximum positive value of 7FFFFFh
and a maximum negative value of 800000h. This
value is subtracted from the conversion data. A
register value of 00000h has no offset correction
(default value). Note that while the offset calibration
register value can correct offsets ranging from –FS to
+FS (as shown in Table 16), to avoid input overload,
the analog inputs cannot exceed the full-scale range.
AINP
Digital
Filter
AINN
7FFFFFh
80000000h
000001h
FFFFFF00h
000000h
00000000h
FFFFFFh
00000100h
800000h
7FFFFF00h
(1) Full 32-bit final output code with zero code input.
FSC[2:0] Registers
The full-scale calibration is a 24-bit word, composed
of three 8-bit registers, as shown in Table 19. The
full-scale calibration value is 24-bit, straight offset
binary, normalized to 1.0 at code 400000h. Table 17
summarizes the scaling of the full-scale register. A
register value of 400000h (default value) has no gain
correction (gain = 1). Note that while the gain
calibration register value corrects gain errors above 1
(gain correction < 1), the full-scale range of the
analog inputs cannot be exceeded to avoid input
overload.
Table 17. Full-Scale Calibration Register Values
FSC REGISTER
GAIN CORRECTION
800000h
2.0
400000h
1.0
200000h
0.5
000000h
0
+
Modulator
FINAL OUTPUT CODE(1)
OFC REGISTER
Output Data
Clipped to 32 Bits
S
´
OFC
Register
FSC Register
400000h
Final Output
-
Figure 50. Calibration Block Diagram
Table 18. Offset Calibration Word
REGISTER
BYTE
BIT ORDER
OFC0
LSB
B7
B6
B5
B4
B3
B2
B1
OFC1
MID
B15
B14
B13
B12
B11
B10
B9
B8
OFC2
MSB
B23 (MSB)
B22
B21
B20
B19
B18
B17
B16
REGISTER
BYTE
FSC0
LSB
B7
B6
B5
B4
B3
B2
B1
B0 (LSB)
FSC1
MID
B15
B14
B13
B12
B11
B10
B9
B8
FSC2
MSB
B23 (MSB)
B22
B21
B20
B19
B18
B17
B16
B0 (LSB)
Table 19. Full-Scale Calibration Word
BIT ORDER
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
27
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
CALIBRATION COMMANDS
OFSCAL Command
Calibration commands may be sent to the ADS1281
to calibrate the conversion data. The values of the
offset and gain calibration registers are internally
written to perform calibration. The appropriate input
signals must be applied to the ADS1281 inputs
before sending the commands. Use slower data rates
to achieve more consistent calibration results; this
effect is a byproduct of the lower noise that these
data rates provide. Also, if calibrating at power-on, be
sure the reference voltage is fully settled.
The OFSCAL command performs an offset
calibration. Before sending the offset calibration
command, a zero input signal must be applied to the
ADS1281 and the inputs allowed to stabilize. When
the command is sent, the ADS1281 averages 16
readings and then writes this value to the OFC
register. The contents of the OFC register may be
subsequently read or written. During offset
calibration, the full-scale correction is bypassed.
Figure 51 shows the calibration command sequence.
After the analog input voltage (and reference) have
stabilized, send the Stop Data Continuous command
followed by the SYNC and Read Data Continuous
commands. 64 data periods later, DRDY goes low.
After DRDY goes low, send the Stop Data
Continuous, then the Calibrate command followed by
the Read Data Continuous command. After 16 data
periods, calibration is complete and conversion data
may be read at this time. The SYNC input must
remain high during the calibration sequence.
GANCAL Command
The GANCAL command performs a gain calibration.
Before sending the GANCAL command, a dc input
signal must be applied that is in the range of, but not
exceeding, positive or negative full-scale. After the
signal has stabilized, the command can be sent. The
ADS1281 averages 16 readings, then computes the
value that compensates for the gain error. The gain
correction value is then written to the FSC register.
The contents of the GANCAL register may be
subsequently read or written. Note that while the gain
calibration command corrects for gain errors above 1
(gain correction < 1), to avoid input overload, the
analog inputs cannot exceed full-scale range. The
gain calibration should be performed after the offset
calibration.
VIN
Fully stable signal input and reference voltage.
Commands
SDATAC
DRDY
SYNC
RDATAC
SDATAC
OFSCAL or
GANCAL
RDATAC
16 Data
Periods
64 Data Periods
Calibration
Complete
SYNC
Figure 51. Offset/Gain Calibration Timing
28
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
USER CALIBRATION
System calibration of the ADS1281 can be performed
without using the calibration commands. This
procedure requires the calibration values to be
externally calculated and then written to the
calibration registers. The steps for this procedure are:
1. Set the OFSCAL[2:0] register = 0h and
GANCAL[2:0] = 400000h. These values set the
offset and gain registers to 0 and 1, respectively.
2. Apply a zero differential input to the input of the
system. Wait for the system to settle and then
average n output readings. Higher numbers of
averaged readings result in more consistent
calibration. Write the averaged value to the OFC
register.
3. Apply a differential positive or negative dc signal,
or an ac signal, less than the full-scale input to
the system. Wait for the system to settle and then
average the n output readings.
DC signal calibration is shown in Equation 10 and
Equation 11. The expected output code is based on
31-bit output data.
Expected Output Code
FSC[2:0] = 400000h ´
Actual Output Code
(10)
31
Expected Output Code = 2 ´ VIN ´
2
VREF
(11)
For ac signal calibration, use an RMS value of
collected data (as shown in Equation 12).
Expected RMS Value
FSC[2:0] = 400000h ´
Actual RMS Value
(12)
The value written to the FSC registers is calculated
by Equation 10 and Equation 11.
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
29
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
COMMANDS
The commands listed in Table 20 control the
operation of the ADS1281. Command operations are
only possible in Register mode. Most commands are
stand-alone (that is, 1 byte in length); the register
reads and writes require a second command byte in
addition to the actual data bytes.
In Read Data Continuous mode, the ADS1281 places
conversion data on the DOUT pin as SCLK is
applied. As a consequence of the potential conflict of
conversion data on DOUT and data placed on DOUT
resulting from a register or Read Data By Command
operation, it is necessary to send a STOP Read Data
Continuous command before Register or Data Read
By Command. The STOP Read Data Continuous
command disables the direct output of conversion
data on the DOUT pin.
A delay of 24 fCLK cycles between commands and
between bytes within a command is required, starting
from the last SCLK rising edge of one command to
the first SCLK rising edge of the following command.
This delay is shown in Figure 52.
DIN
Command
Byte
Command
Byte
SCLK
(1)
tSCLKDLY
(1)
tSCLKDLY = 24/fCLK (min).
Figure 52. Consecutive Commands
Table 20. Command Descriptions
COMMAND
TYPE
DESCRIPTION
1st COMMAND BYTE (1) (2)
WAKEUP
Control
Wake-up from Standby mode
0000 000X (00h or 01h)
STANDBY
Control
Enter Standby mode
0000 001X (02h or 03h)
SYNC
Control
Synchronize the A/D conversion
0000 010X (04h or 5h)
RESET
Control
Reset registers to default values
0000 011X (06h or 07h)
RDATAC
Control
Read data continuous
0001 0000 (10h)
SDATAC
Control
Stop read data continuous
0001 0001 (11h)
RDATA
Data
Read data by command (4)
0001 0010 (12h)
(4)
RREG
Register
001r rrrr (20h + 000r rrrr)
000n nnnn (00h + n nnnn)
WREG
Register
Write nnnnn register(s) at address rrrrr
010r rrrr (40h + 000r rrrr)
000n nnnn (00h + n nnnn)
OFSCAL
Calibration
Offset calibration
0110 0000 (60h)
GANCAL
Calibration
Gain calibration
0110 0001 (61h)
(1)
(2)
(3)
(4)
30
Read nnnnn register(s) at address rrrrr
2nd COMMAND BYTE (3)
X = don't care.
rrrrr = starting address for register read and write commands.
nnnnn = number of registers to be read/written – 1. For example, to read/write three registers, set nnnnn = 2 (00010).
Required to cancel Read Data Continuous mode before sending a command.
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
WAKEUP: Wake-Up From Standby Mode
SDATAC: Stop Read Data Continuous
Description: This command is used to exit the
standby mode. Upon sending the command, the time
for the first data to be ready is illustrated in Figure 41
and Table 13. Sending this command during normal
operation has no effect; for example, reading data by
the Read Data Continuous method with DIN held low.
Description: This command stops the Read Data
Continuous mode. Exiting the Read Data Continuous
mode is required before sending Register and Data
read commands. This command suppresses the
DRDY output, but the ADS1281 continues
conversions.
STANDBY: Standby Mode
RDATA: Read Data By Command
Description: This command places the ADS1281
into Standby mode. In Standby, the device enters a
reduced power state where a low quiescent current
remains to keep the register settings and SPI
interface active. For complete device shutdown, take
the PWDN pin low (register settings are not saved).
To exit Standby mode, issue the WAKEUP command.
The operation of Standby mode is shown in
Figure 53.
Description: This command reads the conversion
data. See the Read Data By Command section for
more details.
DIN
0000 001X
(STANDBY)
0000 000X
(WAKEUP)
RREG: Read Register Data
Description: This command is used to read single or
multiple register data. The command consists of a
two-byte op-code argument followed by the output of
register data. The first byte of the op-code includes
the starting address, and the second byte specifies
the number of registers to read – 1.
First command byte: 001r rrrr, where rrrrr is the
starting address of the first register.
SCLK
Operating
Standby Mode
Operating
Figure 53. STANDBY Command Sequence
SYNC: Synchronize the A/D Conversion
Description: This command synchronizes the A/D
conversion. Upon receipt of the command, the
reading in progress is cancelled and the conversion
process is re-started. In order to synchronize multiple
ADS1281s,
the
command
must
be
sent
simultaneously to all devices. Note that the SYNC pin
must be high for this command.
RESET: Reset the Device
Description: The RESET command resets the
registers to default values, enables the Read Data
Continuous mode, and restarts the conversion
process; the RESET command is functionally the
same as the RESET pin. See Figure 40 for the
RESET command timing.
RDATAC: Read Data Continuous
Description: This command enables the Read Data
Continuous mode (default mode). In this mode,
conversion data can be read from the device directly
without the need to supply a data read command.
Each time DRDY falls low, new data are available to
read. See the Read Data Continuous section for
more details.
Second command byte: 000n nnnn, where nnnnn is
the number of registers – 1 to read.
Starting with the 16th falling edge of SCLK, the
register data appear on DOUT.
The RREG command is illustrated in Figure 54. Note
that a delay of 24 fCLK cycles is required between
each byte transaction.
WREG: Write to Register
Description: This command writes single or multiple
register data. The command consists of a two-byte
op-code argument followed by the input of register
data. The first byte of the op-code contains the
starting address and the second byte specifies the
number of registers to write – 1.
First command byte: 001r rrrr, where rrrrr is the
starting address of the first register.
Second command byte: 000n nnnn, where nnnnn is
the number of registers – 1 to write.
Data byte(s): one or more register data bytes,
depending on the number of registers specified.
Figure 55 illustrates the WREG command.
Note that a delay of 24 fCLK cycles is required
between each byte transaction.
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
31
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
OFSCAL: Offset Calibration
GANCAL: Gain Calibration
Description: This command performs an offset
calibration. The inputs to the converter (or the inputs
to the external pre-amplifier) should be zeroed and
allowed to stabilize before sending this command.
The offset calibration register updates after this
operation. See the Calibration Commands section for
more details.
Description: This command performs a gain
calibration. The inputs to the converter should have a
stable dc input, preferably close to (but not
exceeding) positive full-scale. The gain calibration
register updates after this operation. See the
Calibration Commands section for more details.
tDLY
1
2
3
4
5
6
7
8
9
tDLY
10 11 12 13 14 15 16
tDLY
17 18 19 20 21 22 23 24
25 26
SCLK
DIN
Command Byte 1
DOUT
Command Byte 2
Don't Care
Register Data 5
Register Data 6
Example: Read six registers, starting at register 05h (OFC0)
Command Byte 1 = 0010 0101
Command Byte 2 = 0000 0101
Figure 54. Read Register Data (Table 21 shows tDLY)
tDLY
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16
tDLY
tDLY
17 18 19 20 21 22 23 24
25 26
SCLK
DIN
Command Byte 1
Command Byte 2
Register Data 5
Register Data 6
Example: Write six registers, starting at register 05h (OFC0)
Command Byte 1 = 0100 0101
Command Byte 2 = 0000 0101
Figure 55. Write Register Data (Table 21 shows tDLY)
Table 21. tDRY Value
32
PARAMETER
MIN
tDLY
24fCLK
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
REGISTER MAP
The Register mode (PINMODE = 0) allows read and write access to the device registers. Collectively, the
registers contain all the information needed to configure the device, such as data rate, filter selection, calibration,
etc. The registers are accessed by the RREG and WREG commands. The registers can be accessed individually
or as a block of registers by sending or receiving consecutive bytes.
Table 22. Register Map
ADDRESS
REGISTER
RESET
VALUE
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
00h
ID
X0h
ID3
ID2
ID1
ID0
0
0
0
0
01h
CONFIG0
52h
SYNC
1
DR2
DR1
DR0
PHS
FILTR1
FILTR0
02h
Reserved
08h
0
0
0
0
1
0
0
0
03h
HPF0
32h
HPF07
HPF06
HPF05
HPF04
HPF03
HPF02
HPF01
HPF00
04h
HPF1
03h
HPF15
HPF14
HPF13
HPF12
HPF11
HPF10
HPF09
HPF08
05h
OFC0
00h
OFC07
OFC06
OFC05
OFC04
OFC03
OFC02
OFC01
OFC00
06h
OFC1
00h
OFC15
OFC14
OFC13
OFC12
OFC11
OFC10
OFC09
OFC08
07h
OFC2
00h
OFC23
OFC22
OFC21
OFC20
OFC19
OFC18
OFC17
OFC16
08h
FSC0
00h
FSC07
FSC06
FSC05
FSC04
FSC03
FSC02
FSC01
FSC00
09h
FSC1
00h
FSC15
FSC14
FSC13
FSC12
FSC11
FSC10
FSC09
FSC08
0Ah
FSC2
40h
FSC23
FSC22
FSC21
FSC20
FSC19
FSC18
FSC17
FSC16
BIT 0
ID: ID REGISTER (ADDRESS 00h)
7
6
5
4
3
2
1
0
ID3
ID2
ID1
ID0
0
0
0
0
Reset value = X8h.
Bits[7:4]
ID[3:0]
Factory-programmed identification bits (read-only)
Bits[3:0]
Reserved
Always write '0'
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
33
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
CONFIG0: CONFIGURATION REGISTER 0 (ADDRESS 01h)
7
6
5
4
3
2
1
0
SYNC
1
DR2
DR1
DR0
PHASE
FILTR1
FILTR0
Reset value = 52h.
Bit[7]
SYNC
Synchronization mode
0: Pulse SYNC mode (default)
1: Continuous SYNC mode
Bit[6]
Reserved
Always write '1' (default)
Bits[5:3]
Data Rate Select
DR[2:0]
000: 250SPS
001: 500SPS
010: 1000SPS (default)
011: 2000SPS
100: 4000SPS
Bit[2]
FIR Phase Response
PHASE
0: Linear phase (default)
1: Minimum phase
Bits[1:0]
Digital Filter Select
FILTR[1:0]
Digital filter configuration
00: On-chip filter bypassed, modulator output mode
01: Sinc filter block only
10: Sinc + LPF filter blocks (default)
11: Sinc + LPF + HPF filter blocks
RESERVED: (ADDRESS 02h)
7
6
5
4
3
2
1
0
0
0
0
0
1
0
0
0
Reset value = 08h.
Bits[7:0]
Reserved
Always write '08h'
34
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
HPF1 and HPF0
These two bytes (high-byte and low-byte, respectively) set the corner frequency of the HPF.
HPF0: High-Pass Filter Corner Frequency, Low Byte (Address 03h)
7
6
5
4
3
2
1
0
HP07
HP06
HP05
HP04
HP03
HP02
HP01
HP00
Reset value = 32h.
HPF1: High-Pass Filter Corner Frequency, High Byte (Address 04h)
7
6
5
4
3
2
1
0
HP15
HP14
HP13
HP12
HP11
HP10
HP09
HP08
Reset value = 03h.
OFC2, OFC1, OFC0
These three bytes set the OFC value.
OFC0: Offset Calibration, Low Byte (Address 05h)
7
6
5
4
3
2
1
0
OC07
OC06
OC05
OC04
OC03
OC02
OC01
OC00
Reset value = 00h.
OFC1: Offset Calibration, Mid Byte (Address 06h)
7
6
5
4
3
2
1
0
OC15
OC14
OC13
OC12
OC11
OC10
OC09
OC08
Reset value = 00h.
OFC2: Offset Calibration, High Byte (Address 07h)
7
6
5
4
3
2
1
0
OC23
OC22
OC21
OC20
OC19
OC18
OC17
OC16
Reset value = 00h.
FSC2, FSC1, FSC0
These three bytes set the FSC value.
FSC0: Gain Calibration, Low Byte (Address 08h)
7
6
5
4
3
2
1
0
FSC07
FSC06
FSC05
FSC04
FSC03
FSC02
FSC01
FSC00
Reset value = 00h.
FSC1: Gain Calibration, Mid Byte (Address 09h)
7
6
5
4
3
2
1
0
FSC15
FSC14
FSC13
FSC12
FSC11
FSC10
FSC09
FSC08
Reset value = 00h.
FSC2: Gain Calibration, High Byte (Address 0Ah)
7
6
5
4
3
2
1
0
FSC23
FSC22
FSC21
FSC20
FSC19
FSC18
FSC17
FSC16
Reset value = 40h.
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
35
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
CONFIGURATION GUIDE
The ADS1281 offers two modes of operation: Pin
Control mode and Register Control mode. In Pin
Control mode, the operation of the device is
controlled by the pins; there are no registers to
program. In Register Control mode, the registers are
used to control device operation. After RESET or
power-on, the registers can be configured using the
following procedure:
1. Reset the SPI interface. Before using the SPI
interface, it may be necessary to recover the SPI
interface (undefined I/O power-up sequencing
may cause false SCLK detection). To reset the
SPI interface, toggle the RESET pin or, when in
Read Data Continuous mode, hold SCLK low for
64 DRDY periods.
2. Configure the registers. The registers are
configured by either writing to them individually or
as a group. Software may be configured in either
mode. The STOPC command must be sent
before register read/write operations to cancel the
36
Read Data Continuous mode.
3. Verify register data. The register may be read
back for verification of device communications.
4. Set the data mode. After register configuration,
the device may be configured for Read Data
Continuous mode, either by the Read Data
Continuous command or configured in Read Data
By Register mode using STOPC command.
5. Synchronize readings. Whenever SYNC is high,
the ADS1281 freely runs the data conversions.
To stop and restart the conversions, take SYNC
low and then high.
6. Read data. If the Read Data Continuous mode is
active, the data are read directly after DRDY falls
by applying SCLK pulses. If the Read Data
Continuous mode is inactive, the data can only
be read by Read Data By Command. The Read
Data command must be sent in this mode to read
each conversion result (note that DRDY only
asserts after each read data command is sent).
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
APPLICATION INFORMATION
The ADS1281 is a very high-resolution ADC. Optimal
device performance requires giving special attention
to the support circuitry and printed circuit board
(PCB) design. Locate noisy digital components, such
as microcontrollers and oscillators, in an area of the
PCB away from the converter or front-end
components. Place the digital components close to
the power-entry point to keep the digital current path
short and separate from sensitive analog
components.
As with any precision circuit, use good supply
bypassing techniques. Place the capacitors close to
the device pins.
If switching dc/dc supplies are used to power the
device, check for frequency components of the supply
present within the ADS1281 passband. Voltage ripple
should be kept as low as possible.
Pay special attention to the reference and analog
inputs. With the architecture of the ADS1281, it is
easy for the reference circuit to limit overall
performance if not carefully selected. The 49.9Ω
resistors isolate the op amp from the reference pin
capacitors while providing additional noise filtering.
To achieve rated performance, the inband noise of
the reference circuit should be very low.
Figure 56 shows a typical geophone interface. This
application circuit shows the REF02 (+5V reference)
filtered and buffered by an OPA227. The OPA227
inputs are protected from transient voltages by diode
clamps or gas discharge tubes. This pre-amplifier
configuration has inherently high common-mode
rejection. The 49.9Ω resistors isolate the driver
outputs from the bypass capacitors.
+8V
Input
Protection
Network
10nF
COG
10kW
-2.5V
OPA227
1mF
R2
619W
100W
-2.5V
1m F
15
16
AVDD
AVSS
AVDD
R1
619W
Geophone
100W
R2
619W
BAT54
G=1+2
49.9W
R2
R1
OPA227
49.9W
10nF
COG
10kW
13
10nF
COG
14
AINP
AINN
-8V
AVSS
ADS1281
1kW
10nF
+8V
+5V
47W
200W
1mF
100W
REF02
VREFP
+
+
100mF
18
OPA227
1mF
1m F
-8V
17
VREFN
DGND
-2.5V
6, 12, 23
Figure 56. Geophone Interface, Dual Power-Supply Configuration
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
37
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
Figure 57 shows the digital connection to an FPGA
(field programmable gate array) device. In this
example, two ADS1281s are shown connected. The
DRDY output from each ADS1281 can be used;
however, when the devices are synchronized, the
DRDY output from only one device is sufficient. A
shared SCLK line between the devices is optional.
For best performance, the FPGA and the ADS281s
should operate from the same clock. Avoid ringing on
the digital inputs. 47Ω resistors in series with the
digital traces can help to reduce ringing by controlling
impedances. Place the resistors at the source (driver)
end of the trace. Unused digital inputs should not
float; tie them directly to DVDD or GND.
The modulator over-range flag (MFLAG) from each
device ties to the FPGA. For synchronization, one
SYNC control line connects all ADS1281 devices.
The RESET line also connects to all ADS1281
devices.
4.096MHz Clock
47W
+3.3V
22
(1)
1
CLK
DVDD
47W
ADS1281
20
RESET
1mF
4
24
5
47W
5
DIN1
DIN
PINMOD
47W
2
SCLK1
SCLK
47W
10
SYNC
HPF/SYNC
47W
11
MFLAG1
MFLAG
DGND
CLK Input
DOUT1
DOUT
BYPAS
1mF
RESET
47W
4, 12, 23
+3.3V
1
(1)
FPGA
DVDD
CLK
ADS1281
1mF
20
RESET
4
24
47W
DOUT2
DOUT
BYPAS
5
5
PINMOD
DIN2
DIN
1mF
2
SCLK2
SCLK
47W
10
HPF/SYNC
47W
11
MFLAG
MFLAG2
3
DGND
47W
DRDY
DRDY
6, 12, 23
NOTE: Dashed lines are optional.
(1)
For DVDD < 2.25V, see the DVDD Power Supply section.
Figure 57. FPGA Device
38
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
APPENDIX
Table 23. FIR Stage Coefficients
SECTION 1
COEFFICIENT
SECTION 2
Scaling = 1/8388608
SECTION 3
SECTION 4
Scaling = 134217728
Scaling = 134217728
LINEAR
PHASE
MINIMUM PHASE
LINEAR
PHASE
MINIMUM PHASE
b0
–10944
–774
–73
819
–132
11767
b1
0
0
–874
8211
–432
133882
b2
103807
8994
–4648
44880
–75
769961
b3
0
0
–16147
174712
2481
2940447
b4
–507903
–51663
–41280
536821
6692
8262605
b5
0
0
–80934
1372637
7419
17902757
b6
2512192
199523
–120064
3012996
–266
30428735
b7
4194304
0
–118690
5788605
–10663
40215494
b8
2512192
–629120
–18203
9852286
–8280
39260213
b9
0
0
224751
14957445
10620
23325925
b10
–507903
2570188
580196
20301435
22008
–1757787
b11
0
4194304
893263
24569234
348
–21028126
b12
103807
2570188
891396
26260385
–34123
–21293602
b13
0
0
293598
24247577
–25549
–3886901
b14
–10944
–629120
–987253
18356231
33460
14396783
b15
0
–2635779
9668991
61387
16314388
b16
199523
–3860322
327749
–7546
1518875
b17
0
–3572512
–7171917
–94192
–12979500
b18
–51663
–822573
–10926627
–50629
–11506007
b19
0
4669054
–10379094
101135
2769794
b20
8994
12153698
–6505618
134826
12195551
b21
0
19911100
–1333678
–56626
6103823
b22
–774
25779390
2972773
–220104
–6709466
b23
27966862
5006366
–56082
–9882714
b24
Only half shown;
symmetric starting
with b22.
4566808
263758
–353347
2505652
231231
8629331
126331
–215231
5597927
b27
–1496514
–430178
–4389168
b28
–1933830
34715
–7594158
b29
–1410695
580424
–428064
b30
–502731
283878
6566217
b31
245330
–588382
4024593
b32
565174
–693209
–3679749
b33
492084
366118
–5572954
b34
231656
1084786
332589
5136333
b25
b26
b35
–9196
132893
b36
–125456
–1300087
2351253
b37
–122207
–878642
–3357202
b38
–61813
1162189
–3767666
b39
–4445
1741565
1087392
b40
22484
–522533
3847821
b41
22245
–2490395
919792
b42
10775
–688945
–2918303
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
39
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
Table 23. FIR Stage Coefficients (continued)
SECTION 1
SECTION 2
SECTION 3
SECTION 4
Scaling = 134217728
MINIMUM PHASE
MINIMUM PHASE
b43
940
2811738
–2193542
b44
–2953
2425494
1493873
b45
–2599
–2338095
2595051
b46
–1052
–4511116
–79991
b47
–43
641555
–2260106
b48
214
6661730
–963855
b49
132
2950811
1482337
b50
33
–8538057
1480417
Scaling = 1/8388608
b51
–10537298
–586408
b52
9818477
–1497356
b53
41426374
–168417
b54
56835776
1166800
b55
Only half shown;
symmetric starting
with b53.
644405
b56
b57
40
Scaling = 134217728
LINEAR
PHASE
COEFFICIENT
LINEAR
PHASE
–675082
–806095
b58
211391
b59
740896
b60
141976
b61
–527673
b62
–327618
b63
278227
b64
363809
b65
–70646
b66
–304819
b67
–63159
b68
205798
b69
124363
b70
–107173
b71
–131357
b72
31104
b73
107182
b74
15644
b75
–71728
b76
–36319
b77
38331
b78
38783
b79
–13557
b80
–31453
b81
–1230
b82
20983
b83
7729
b84
–11463
b85
–8791
b86
4659
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
ADS1281
www.ti.com
SBAS378A – SEPTEMBER 2007 – REVISED NOVEMBER 2007
Table 23. FIR Stage Coefficients (continued)
SECTION 1
SECTION 2
SECTION 3
SECTION 4
Scaling = 134217728
COEFFICIENT
LINEAR
PHASE
Scaling = 1/8388608
Scaling = 134217728
MINIMUM PHASE
LINEAR
PHASE
b87
MINIMUM PHASE
7126
b88
–732
b89
–4687
b90
–976
b91
2551
b92
1339
b93
–1103
b94
–1085
b95
314
b96
681
b97
16
b98
–349
b99
–96
b100
144
b101
78
b102
–46
b103
–42
b104
9
b105
16
b106
0
b107
–4
1-
1-2
cos wN + sin wN - 1
cos wN
HPF Gain Error Factor =
2-
cos wN + sin wN - 1
cos wN
(13)
See the HPF Stage section for an example of how to use this equation.
Table 24. tDR Time for Data Ready (Sinc Filter)
(1)
fDATA
fCLK (1)
128k
440
64k
616
32k
968
16k
1672
8k
2824
For SYNC and Wake-Up commands, fCLK = number of CLK cycles from next rising CLK edge directly after eighth rising SCLK edge to
DRDY falling edge. For Wake-Up command only, subtract two fCLK cycles.
Table 24 is referenced by Table 10 and Table 12.
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1281
41
PACKAGE OPTION ADDENDUM
www.ti.com
19-Nov-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
ADS1281IPW
ACTIVE
TSSOP
PW
24
60
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
ADS1281IPWG4
ACTIVE
TSSOP
PW
24
60
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
ADS1281IPWR
ACTIVE
TSSOP
PW
24
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
ADS1281IPWRG4
ACTIVE
TSSOP
PW
24
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
8-Nov-2007
TAPE AND REEL BOX INFORMATION
Device
ADS1281IPWR
Package Pins
PW
24
Site
Reel
Diameter
(mm)
Reel
Width
(mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
SITE 60
330
16
6.95
8.3
1.6
8
Pack Materials-Page 1
W
Pin1
(mm) Quadrant
16
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
8-Nov-2007
Device
Package
Pins
Site
Length (mm)
Width (mm)
Height (mm)
ADS1281IPWR
PW
24
SITE 60
346.0
346.0
33.0
Pack Materials-Page 2
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
0,65
14
0,10 M
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
8
14
16
20
24
28
A MAX
3,10
5,10
5,10
6,60
7,90
9,80
A MIN
2,90
4,90
4,90
6,40
7,70
9,60
DIM
4040064/F 01/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties
may be subject to additional restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Telephony
www.ti.com/telephony
Low Power
Wireless
www.ti.com/lpw
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated