PG600A THRU PG600K GLASS PASSIVATED JUNCTION PLASTIC RECTIFIER VOLTAGE - 50 to 800 Volts CURRENT - 6.0 Amperes FEATURES l High surge current capability l Plastic package has Underwriters Laboratory P600 Flammability Classification 94V-O Utilizing Flame Retardant Epoxy Molding Compound l l Glass passivated junction in P600 package High current operation 6.0 Amperes @ TA=75 ¢J l Exceeds environmental standards of MIL-S-19500/228 MECHANICAL DATA Case: Molded plastic, P600 Terminals: axial leads, solderable per MIL-STD-202, Method 208 Polarity: Color band denotes cathode Mounting Position: Any Weight: 0.07 ounce, 2.1 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS *@ TA=25 ¢J unless otherwise specified. Single phase, half-wave,60 Hz, resistive or inductive load. **All values except Maximum RMS Voltage are registered JEDEC parameters. PG600A PG600B PG600D PG600G PG600J PG600K UNITS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at TA=75 ¢J Maximum Overload Surge Current at 1 cycle (NOTE 1) Maximum Forward Voltage at 6.0 ADC Maximum Full Load Reverse Current Full Cycle Average at 25 ¢J Maximum DC Reverse Current at Rated DC Blocking Voltage and 100 ¢J Typical Junction capacitance (Note 2) CJ Typical Thermal Resistance (Note 3) R £KJA Typical Thermal Resistance (Note 3) R £KJL Operating Temperature Range Storage Temperature Range 50 35 50 100 70 100 200 140 200 400 280 400 300 1.0 10 V V V A A A V £g ADC 0.3 m ADC 150.0 20.0 4.0 PF ¢J /W ¢J /W ¢J ¢J 6.0 600 420 600 800 560 800 -55 to +150 -55 to +150 NOTES: 1. Peak forward surge current, per 8.3ms single half-sine-wave superimposed on rated load(JECED method) 2. Measured at 1 MHZ and applied reverse voltage of 4.0 volts 3. Thermal resistance from junction to ambient and from junction to lead at 0.375"(9.5mm) lead length P.C.B. mounted with 1.1×1.1(30×30mm) copper pads RATING AND CHARACTERISTIC CURVES PG600A THRU PG600K AVERAGE FORWARD CURRENT (10)-AMP INSTANTANEOUS REVERSE CURRENT, £g A 100 10 25 ¢J 1 8.0 6.0 . 5" LOAD LENGTH 4.0 2.0 0 50 75 100 125 150 175 200 AMBIENT TEMPERATURE, ¢J 0.1 0 20 40 60 80 100 120 Fig. 2-FORWARD DERATING CURVE 140 MAXIMUM FORWARD CURRENT-1FM(ApK) PERCENT OF RATED PEAK REVERSE VOLTAGE TRANSIENT THERMAL IMPEDANCE, ¢J /W Fig. 1-TYPICAL REVERSE CHARACTERISTICS 100 10 1 0.1 0.01 0.1 1 10 10 5% 1.0 MEDIAN 10% 0.1 .01 0.5 0.6 0.7 0.8 1.1 1.3 1.5 1.7 MAXIMUM FORWARD VOLTAGE-VFM(VpK) 100 t, PULSE DURATION. Sec. Fig. 4-TYPICAL FORWARD CHARACTERISTICS PEAK FORWARD SURGE CURRENT AMPERES Fig. 3-TYPICAL TRANSIENT THERMAL IMPEDANCE 500 400 300 8.3ms SINGLE HALE SINE-WAVE T J = 25¢J 200 100 0 1 10 100 NUMBER OF CYCLES AT 60Hz Fig. 5-PEAK FORWARD SURGE CURRENT