PI74FCT16374/162374/162H374T PI74FCT16374T 16-BIT REGISTERS (3-STATE) 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 PI74FCT162374T PI74FCT162H374T 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Fast CMOS 16-Bit Registers (3-State) Product Features: Product Description: Common Features: • PI74FCT16374T, PI74FCT162374T, and PI74FCT162H374T are high-speed, low power devices with high current drive. • Vcc = 5V ±10% • Hysteresis on all inputs • Packages available: – 48-pin 240 mil wide plastic TSSOP (A) – 48-pin 300 mil wide plastic SSOP (V) PI74FCT16374T Features: • High output drive: IOH = –32 mA; IOL = 64 mA • Power off disable outputs permit "live insertion" • Typical VOLP (Output Ground Bounce) < 1.0V at VCC = 5V, TA = 25°C PI74FCT162374T Features: • Balanced output drivers: ±24 mA • Reduced system switching noise • Typical VOLP (Output Ground Bounce) < 0.6V at VCC = 5V, TA = 25°C PI74FCT162H374T Features: • Bus Hold retains last active bus state during 3-state • Eliminates the need for external pull-up resistors Pericom Semiconductor’s PI74FCT series of logic circuits are produced in the Company’s advanced 0.6 micron CMOS technology, achieving industry leading speed grades. The PI74FCT16374T, PI74FCT162374T, and PI74FCT162H374T are 16-bit octal registers designed with 16 D-type flip-flops with a buffered common clock and 3-state outputs. The Output Enable (xOE) and clock (xCLK) controls are organized to operate as two 8-bit registers or one 16-bit register. When OE is HIGH, the outputs are in the high impedance state. Input data meeting the setup and hold time requirements of the D inputs is transferred to the O outputs on the LOW-to-HIGH transition of the clock input. The PI74FCT16374T output buffers are designed with a Power-Off disable allowing “live insertion” of boards when used as backplane drivers. The PI74FCT162374T has ±24 mA balanced output drivers. It is designed with current limiting resistors at its outputs to control the output edge rate resulting in lower ground bounce and undershoot. This eliminates the need for external terminating resistors for most interface applications. The PI74FCT162H374T has “Bus Hold” which retains the input’s last state whenever the input goes to high-impedance preventing “floating” inputs and eliminating the need for pull-up/down resistors. Logic Block Diagram 1OE 2OE 1CLK 2CLK 1D0 2D0 D D 1O0 C 2O0 C TO 7 OTHER CHANNELS TO 7 OTHER CHANNELS 1 PS2034A 03/28/01 PI74FCT16374/162374/162H374T 16-BIT REGISTERS (3-STATE) 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Product Pin Description Pin Name xOE xCLK xDx xOx GND VCC Note: Truth Table(1) Description 3-State Output Enable Inputs (Active LOW) Clock Inputs Inputs(1) 3-State Outputs Ground Power Function High-Z Load Register 1. For the PI74FCT162H374T, these pins have “Bus Hold.” All other pins are standard, outputs, or I/Os. XDX X X L H L H Inputs XCLK L H ↑ ↑ ↑ ↑ XOE H H L L H H Outputs XOX Z Z L H Z Z Note: 1. H = High Voltage Level L = Low Voltage Level X = Don’t Care Z = High Impedance ↑ = LOW-to-HIGH transition Product Pin Configuration 1OE 1 48 1CLK 1O0 2 47 1D0 1O1 3 46 1D1 GND 4 45 GND 1O2 5 44 1D2 1O3 6 43 1D3 VCC 7 42 VCC 1O4 8 41 1D4 1O5 9 40 1D5 GND 10 39 11 1O7 48-PIN V48 38 A48 37 12 GND 1O6 2O0 13 36 2D0 2O1 14 35 2D1 GND 15 34 GND 2O2 16 33 2D2 2O3 17 32 2D3 VCC 18 31 VCC 2O4 19 30 2D4 2O5 20 29 2D5 GND 21 28 GND 2O6 22 27 2D6 2O7 23 26 2D7 2OE 24 25 2CLK 1D6 1D7 2 PS2034A 03/28/01 PI74FCT16374/162374/162H374T 16-BIT REGISTERS (3-STATE) 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature .................................................................... –65°C to +150°C Ambient Temperature with Power Applied .................................... –40°C to +85°C Supply Voltage to Ground Potential (Inputs & Vcc Only) .............. –0.5V to +7.0V Supply Voltage to Ground Potential (Outputs & D/O Only) ........... –0.5V to +7.0V DC Input Voltage ............................................................................ –0.5V to +7.0V DC Output Current ..................................................................................... 120 mA Power Dissipation ..........................................................................................1.0W Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. DC Electrical Characteristics (Over the Operating Range, TA = –40°C to +85°C, VCC = 5.0V ± 10%) Parameters Description VIH VIL IIH IIH IIH IIH IIL IIL IIL IIL IBHH IBHL IOZH(5) IOZL(5) VIK IOS IO VH Input HIGH Voltage Input LOW Voltage Input HIGH Current Input HIGH Current Input HIGH Current Input HIGH Current Input LOW Current Input LOW Current Input LOW Current Input LOW Current Bus Hold Sustain Current High Impedance Output Current Clamp Diode Voltage Short Circuit Current Output Drive Current Input Hysteresis Test Conditions(1) Guaranteed Logic HIGH Level Guaranteed Logic LOW Level Standard Input , VCC = Max. Standard I/O , VCC = Max. Bus Hold Input(4), VCC = Max. Bus Hold I/O(4), VCC = Max. Standard Input , VCC = Min. Standard I/O , VCC = Min. Bus Hold Input(4), VCC = Min. Bus Hold I/O(4), VCC = Min. Bus Hold Input(4), VCC = Min. VCC = Max. VCC = Max. VCC = Min., IIN = –18 mA VCC = Max.(3), VOUT = GND VCC = Max.(3), VOUT = 2.5V Min. Typ(2) Max. Units 0.8 1 1 ±100 ±100 –1 –1 ±100 ±100 V V µA µA µA µA µA µA µA µA µA 2.0 VIN = VCC VIN = VCC VIN = VCC VIN = VCC VIN = GND VIN = GND VIN = GND VIN = GND VIN = 2.0V VIN = 0.8V VOUT = 2.7V VOUT = 0.5V –50 +50 –80 –50 –0.7 –140 1 –1 –1.2 –200 –180 100 µA µA V mA mA mV Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at Vcc = 5.0V, +25°C ambient and maximum loading. 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 4. Pins with Bus Hold are identified in the pin description. 5. This specification does not apply to bi-directional functionalities with Bus Hold. 3 PS2034A 03/28/01 PI74FCT16374/162374/162H374T 16-BIT REGISTERS (3-STATE) 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 PI74FCT16374T Output Drive Characteristics (Over the Operating Range) Test Conditions(1) Parameters Description VOH Output HIGH Voltage VCC = Min., VIN = VIH or VIL VOL IOFF Output LOW Voltage Power Down Disable VCC = Min., VIN = VIH or VIL VCC = 0V, VIN or VOUT ≤4.5V IOH = –3.0 mA IOH = –15.0 mA IOH = –32.0 mA IOL = 64 mA Min. Typ(2) 2.5 2.4 2.0 3.5 3.5 3.0 0.2 — 0.55 ±100 V µA Min. Typ(2) Max. Units 2.4 3.3 0.3 115 –115 0.55 150 –150 V V mA mA — Max. Units V PI74FCT162374T/162H374T Output Drive Characteristics (Over the Operating Range) Test Conditions(1) Parameters Description VOH VOL IODL IODH Output HIGH Voltage Output LOW Voltage Output LOW Current Output HIGH Current VCC = Min., VIN = VIH or VIL IOH = –24.0 mA VCC = Min., VIN = VIH or VIL IOL = 24 mA VCC = 5V, VIN = VIH OR VIL, VOUT = 1.5V(3) VCC = 5V, VIN = VIH OR VIL, VOUT = 1.5V(3) 60 –60 Capacitance (TA = 25°C, f = 1 MHz) Parameters(4) CIN COUT Description Test Conditions Typ Max. Units Input Capacitance Output Capacitance VIN = 0V VOUT = 0V 4.5 5.5 6 8 pF pF Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at Vcc = 5.0V, +25°C ambient and maximum loading. 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 4. This parameter is determined by device characterization but is not production tested. 4 PS2034A 03/28/01 PI74FCT16374/162374/162H374T 16-BIT REGISTERS (3-STATE) 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Power Supply Characteristics Parameters Description Test Conditions(1) Min. Typ(2) Max. Units ICC Quiescent Power Supply Current VCC = Max. VIN = GND or VCC 0.1 500 µA ∆ICC Supply Current per Input @ TTL HIGH VCC = Max. VIN = 3.4V(3) 0.5 1.5 mA ICCD Supply Current per Input per MHz(4) VCC = Max., Outputs Open XOE = GND One Bit Toggling 50% Duty Cycle VIN = VCC VIN = GND 60 100 µA/ MHz IC Total Power Supply Current(6) VCC = Max., Outputs Open fCP = 10 MHZ 50% Duty Cycle XOE = GND fI = 5 MHZ 50% Duty Cycle One Bit Toggling VIN = VCC VIN = GND 0.6 1.5(5) mA VIN = 3.4V VIN = GND 1.1 3.0(5) VCC = Max., Outputs Open fCP = 10 MHZ 50% Duty Cycle XOE = GND 16 Bits Toggling fI = 2.5 MHZ VIN = VCC VIN = GND 3.0 5.5(5) VIN = 3.4V VIN = GND 7.5 19.0(5) 50% Duty Cycle Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device. 2. Typical values are at Vcc = 5.0V, +25°C ambient. 3. Per TTL driven input (VIN = 3.4V); all other inputs at Vcc or GND. 4. This parameter is not directly testable, but is derived for use in Total Power Supply Calculations. 5. Values for these conditions are examples of the Icc formula. These limits are guaranteed but not tested. 6. IC =IQUIESCENT + IINPUTS + IDYNAMIC IC = ICC + ∆ICC DHNT + ICCD (fCP/2 + fINI) ICC = Quiescent Current ∆ICC = Power Supply Current for a TTL High Input (VIN = 3.4V) DH = Duty Cycle for TTL Inputs High NT = Number of TTL Inputs at DH ICCD = Dynamic Current Caused by an Input Transition Pair (HLH or LHL) fCP = Clock Frequency for Register Devices (Zero for Non-Register Devices) fI = Input Frequency NI = Number of Inputs at fI All currents are in milliamps and all frequencies are in megahertz. 5 PS2034A 03/28/01 PI74FCT16374/162374/162H374T 16-BIT REGISTERS (3-STATE) 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 PI74FCT16374T Switching Characteristics over Operating Range Parameters t PLH t PHL tPZH tPZL t PHZ t PLZ tSU tH tW tSK(o) (1) 16374T 16374AT 16374CT 16374DT 16374ET Com. Com. Com. Com. Com. Description Conditions Min Max Min Max Min Max Min Max Min Max Unit Propagation Delay xCLKx to xOx Output Enable Time xOE to xOx Output Disable Time(3) xOE to xOx Setup Time HIGH or LOW, XDX to XCLK Hold Time HIGH or LOW, XDX to XCLK xCLK Pulse Width HIGH or LOW(3) Output Skew(4) CL = 50 pF RL = 500Ω 2.0 10.0 2.0 6.5 2.0 5.2 2.0 4.2 1.5 3.7 ns 1.5 12.5 1.5 6.5 1.5 5.5 1.5 4.8 1.5 4.4 ns 1.5 8.0 1.5 5.5 1.5 5.0 1.5 4.0 1.5 4.0 ns 2.0 — 2.0 — 2.0 — 2.0 — 1.5 — ns 1.5 — 1.5 — 1.5 — 1.0 — 0.0 — ns 7.0 — 5.0 — 5.0 — 3.0 — 3.0 — ns — 0.5 — 0.5 — 0.5 — 0.5 — 0.5 ns PI74FCT162374T Switching Characteristics over Operating Range Parameters t PLH t PHL tPZH tPZL t PHZ t PLZ tSU tH tW tSK(o) (1) 162374T 162374AT 162374CT 162374DT 162374ET Com. Com. Com. Com. Com. Description Conditions Min Max Min Max Min Max Min Max Min Max Unit Propagation Delay xCLKx to xOx Output Enable Time xOE to xOx Output Disable Time(3) xOE to xOx Setup Time HIGH or LOW, XDX to XCLK Hold Time HIGH or LOW, XDX to XCLK xCLK Pulse Width HIGH or LOW(3) Output Skew(4) CL = 50 pF RL = 500Ω 2.0 10.0 2.0 6.5 2.0 5.2 2.0 4.2 1.5 3.7 ns 1.5 12.5 1.5 6.5 1.5 5.5 1.5 4.8 1.5 4.4 ns 1.5 8.0 1.5 5.5 1.5 5.0 1.5 4.0 1.5 4.0 ns 2.0 — 2.0 — 2.0 — 2.0 — 1.5 — ns 1.5 — 1.5 — 1.5 — 1.0 — 0.0 — ns 7.0 — 5.0 — 5.0 — 3.0 — 3.0 — ns — 0.5 — 0.5 — 0.5 — 0.5 — 0.5 ns Notes: 1. See test circuit and wave forms. 2. Minimum limits are guaranteed but not tested on Propagation Delays. 3. This parameter is guaranteed but not production tested. 4. Skew between any two outputs, of the same package, switching in the same direction. This parameter is guaranteed by design. 6 PS2034A 03/28/01 PI74FCT16374/162374/162H374T 16-BIT REGISTERS (3-STATE) 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 PI74FCT162H374T Switching Characteristics over Operating Range 162H374T 162H374AT 162H374CT 162H374DT 162H374ET Com. Parameters t PLH t PHL tPZH tPZL tPHZ tPLZ tSU tH tW tSK(o) Com. Com. Com. Com. Description Conditions(1) Min Max Min Max Min Max Min Max Min Max Unit Propagation Delay xCLKx to xOx Output Enable Time xOE to xOx Output Disable Time(3) xOE to xOx Setup Time HIGH or LOW, XDX to XCLK Hold Time HIGH or LOW, XDX to XCLK xCLK Pulse Width HIGH or LOW(3) Output Skew(4) CL = 50 pF RL = 500Ω 2.0 10.0 2.0 6.5 2.0 5.2 2.0 4.2 1.5 3.7 ns 1.5 12.5 1.5 6.5 1.5 5.5 1.5 4.8 1.5 4.4 ns 1.5 8.0 1.5 5.5 1.5 5.0 1.5 4.0 1.5 4.0 ns 2.0 — 2.0 — 2.0 — 2.0 — 1.5 — ns 1.5 — 1.5 — 1.5 — 1.0 — 0.0 — ns 7.0 — 5.0 — 5.0 — 3.0 — 3.0 — ns — 0.5 — 0.5 — 0.5 — 0.5 — 0.5 ns Notes: 1. See test circuit and wave forms. 2. Minimum limits are guaranteed but not tested on Propagation Delays. 3. This parameter is guaranteed but not production tested. 4. Skew between any two outputs, of the same package, switching in the same direction. This parameter is guaranteed by design. Pericom Semiconductor Corporation 2380 Bering Drive • San Jose, CA 95131 • 1-800-435-2336 • Fax (408) 435-1100 • http://www.pericom.com 7 PS2034A 03/28/01