PHILIPS SAA3010

INTEGRATED CIRCUITS
DATA SHEET
SAA3010
Infrared remote control transmitter
RC-5
Product specification
File under Integrated Circuits, IC01
June 1989
Philips Semiconductors
Product specification
Infrared remote control transmitter RC-5
SAA3010
The device can generate 2048 different commands and
utilizes a keyboard with a single pole switch for each key.
The commands are arranged so that 32 systems can be
addressed, each system containing 64 different
commands. The keyboard interconnection is illustrated by
Fig.3.
FEATURES
• Low voltage requirement
• Biphase transmission technique
• Single pin oscillator
• Test mode facility
The circuit response to legal (one key pressed at a time)
and illegal (more than one key pressed at a time) keyboard
operation is specified in the section “Keyboard operation”.
GENERAL DESCRIPTION
The SAA3010 is intended as a general purpose (RC-5)
infrared remote control system for use where a low voltage
supply and a large debounce time are expected.
QUICK REFERENCE DATA
PARAMETER
SYMBOL
MIN.
TYP.
MAX.
UNIT
Supply voltage range
VDD
2
−
7
V
Input voltage range (note 1)
VI
−0.5
−
VDD+0.5
V
Input current
II
−
−
±10
mA
Output voltage range (note 1)
VO
−0.5
−
VDD+0.5
V
Output current
IO
−
−
±10
mA
Operating ambient temperature
range
Tamb
−25
−
85
°C
Note
1. VDD+0.5 V must not exceed 9 V.
WARNING
The use of this device must conform with the Philips Standard number URT-0421.
PACKAGE OUTLINES
28-lead DIL plastic; (SOT117); SOT117-1; 1996 September 11.
28-lead mini-pack; plastic (SO28; SOT136A); SOT136-1; 1996 September 11.
June 1989
2
Philips Semiconductors
Product specification
Infrared remote control transmitter RC-5
SAA3010
BLOCK DIAGRAM
handbook, full pagewidth
SAA3010
OSC
TP1
TP2
SSM
Z3
Z2
Z1
Z0
X7
X6
X5
X4
X3
X2
X1
X0
18
OSC
3 × 21
20
2
MASTER
RESET
GENERATOR
TEST
MODE
19
MODE
SELECTION
DECODER
213
DIVIDER
CONTROL
UNIT
6
5
4
3
1
27
26
25
KEYBOARD
ENCODER
17
COMMAND
AND
SYSTEM
ADDRESS
LATCH
24
23
22
21
16
15
KEYBOARD
DRIVER
DECODER
13
12
11
10
PARALLEL
TO SERIAL
CONVERTER
OUTPUT
8
7
9
14
28
VSS
VDD
MGE347
DATA
MDATA
Fig.1 Block diagram.
June 1989
3
DR0
DR1
DR2
DR3
DR4
DR5
DR6
DR7
Philips Semiconductors
Product specification
Infrared remote control transmitter RC-5
SAA3010
PINNING
PIN
MNEMONIC (1)
FUNCTION
1
X7 (IPU)
sense input from key matrix
2
SSM (I)
system mode selection input
3-6
Z0-Z3 (IPU)
sense inputs from key matrix
X7
1
28 VDD
7
MDATA (OP3)
generated output data
modulated with 1/12 the
oscillator frequency at a 25%
duty factor
SSM
2
27 X6
Z0
3
26 X5
Z1
4
25 X4
handbook, halfpage
8
DATA (OP3)
generated output information
Z2
5
24 X3
9-13
DR7-DR3
(ODN)
scan drivers
Z3
6
23 X2
MDATA
7
14
VSS
ground (0 V)
22 X1
SAA3010
DATA
8
21 X0
DR7
9
20 TP1
oscillator input
DR6 10
19 TP2
TP2 (I)
test point 2
DR5 11
18 OSC
TP1 (I)
test point 1
DR4 12
17 DR0
DR3 13
16 DR1
VSS 14
15 DR2
15-17 DR2-DR0
(ODN)
scan drivers
18
OSC (I)
19
20
21-27 X0-X6 (IPU)
sense inputs from key matrix
28
voltage supply
VDD(I)
Note
MGE346
1. (I) = input
(IPU) = input with p-channel pull-up transistor
(ODN) = output with open drain n-channel transistor
(OP3) = output 3-state
Fig.2 Pinning diagram.
June 1989
4
Philips Semiconductors
Product specification
Infrared remote control transmitter RC-5
SAA3010
handbook, full pagewidth
DR0
X0
X1
X2
X3
X4
X5
X6
X7
Z0
Z1
Z2
Z3
17
DR1
16
DR2
15
DR3
13
DR4
12
DR5
11
DR6
10
DR7
9
21
22
23
24
25
26
SAA3010
27
1
3
4
5
6
8
7
2
20
19
18
DATA
MDATA
SSM
TP1
TP2
OSC
MGE348
Fig.3 Keyboard interconnection.
June 1989
5
Philips Semiconductors
Product specification
Infrared remote control transmitter RC-5
SAA3010
FUNCTIONAL DESCRIPTION
Keyboard operation
Every connection of one X-input and one DR-output will be recognized as a legal key operation and will cause the device
to generate the corresponding code. The same applies to every connection of one Z-input to one DR-output with the
proviso that SSM must be LOW. When SSM is HIGH a wired connection must exist between a Z-input and a DR-output.
If no connection is present the system number will not be generated. Activating two or more X-inputs, Z-inputs or Z-inputs
and X-inputs at the same time is an illegal action and inhibits further activity (oscillator will not start).
When one X- or Z-input is connected to more than one DR-output, the last scan signal will be considered as legal.
The maximum value of the contact series resistance of the switched keyboard is 7 kΩ.
Inputs
In the quiescent state the command inputs X0 to X7 are held HIGH by an internal pull-up transistor. When the system
mode selection (SSM) input is LOW and the system is quiescent, the system inputs Z0 to Z3 are also held HIGH by an
internal pull-up transistor. When SSM is HIGH the pull-up transistor for the Z-inputs is switched off, in order to prevent
current flow, and a wired connection in the Z-DR matrix provides the system number.
Outputs
The output signal DATA transmits the generated information in accordance with the format illustrated by Fig.4 and
Tables 1 and 2. The code is transmitted using a biphase technique as illustrated by Fig.5. The code consists of four parts:
• Start part −1.5 bits (2 × logic 1)
• Control part −1 bit
• System part −5 bits
• Command part −6 bits
The output signal MDATA transmits the generated information modulated by 1/12 of the oscillator frequency with a 50%
duty factor.
In the quiescent state both DATA and MDATA are non-conducting (3-state outputs).
The scan driver outputs DR0 to DR7 are open drain n-channel transistors and conduct when the circuit is quiescent.
After a legal key operation the scanning cycle is started and the outputs switched to the conductive state one by one.
The DR-outputs were switched off at the end of the preceding debounce cycle.
June 1989
6
Philips Semiconductors
Product specification
Infrared remote control transmitter RC-5
SAA3010
handbook, full pagewidth
ONE CODE
MSB
start
debounce
time
(16 bit-times)
scan
time
start
bits
control
bit
LSB MSB
system bits
LSB
command bits
TWO SUCCESSIVE CODES
2nd. code
1st. code
MGE349
start
Where:
debounce time + scan time = 18 bit-times
repetition time = 4 × 16 bit-times
Fig.4 Data output format.
handbook, halfpage
logic 1
logic 0
MGE350
Where:
1 bit-time = 3.28 × TOSC = 1.778 ms (typ.)
Fig.5 Biphase transmission technique.
June 1989
7
Philips Semiconductors
Product specification
Infrared remote control transmitter RC-5
Table 1
SAA3010
Command matrix (X-DR)
CODE X-LINES
NO. 0
1
2
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
June 1989
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
DR-LINES
3
4
5
6
7
0
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1
2
•
•
•
•
8
•
•
•
•
COMMAND BITS
3
•
•
•
•
4
•
•
•
•
5
•
•
•
•
6
•
•
•
•
7
•
•
•
•
5
4
3
2
1
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
1
0
0
0
0
0
1
1
0
0
0
1
0
0
0
0
0
1
0
1
0
0
0
1
1
0
0
0
0
1
1
1
0
0
1
0
0
0
0
0
1
0
0
1
0
0
1
0
1
0
0
0
1
0
1
1
0
0
1
1
0
0
0
0
1
1
0
1
0
0
1
1
1
0
0
0
1
1
1
1
0
1
0
0
0
0
0
1
0
0
0
1
0
1
0
0
1
0
0
1
0
0
1
1
0
1
0
1
0
0
0
1
0
1
0
1
0
1
0
1
1
0
0
1
0
1
1
1
0
1
1
0
0
0
0
1
1
0
0
1
0
1
1
0
1
0
0
1
1
0
1
1
0
1
1
1
0
0
0
1
1
1
0
1
0
1
1
1
1
0
0
1
1
1
1
1
Philips Semiconductors
Product specification
Infrared remote control transmitter RC-5
CODE X-LINES
NO. 0
1
2
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
June 1989
SAA3010
DR-LINES
3
4
•
•
•
•
•
•
•
•
5
•
•
•
•
•
•
•
•
6
7
0
•
•
•
•
•
•
•
•
•
•
•
1
2
•
•
•
•
•
•
COMMAND BITS
3
•
•
•
4
•
•
•
5
•
•
•
6
•
•
•
7
•
•
•
• •
•
•
•
•
•
•
•
•
•
•
•
•
•
•
9
5
4
3
2
1
0
1
0
0
0
0
0
1
0
0
0
0
1
1
0
0
0
1
0
1
0
0
0
1
1
1
0
0
1
0
0
1
0
0
1
0
1
1
0
0
1
1
0
1
0
0
1
1
1
1
0
1
0
0
0
1
0
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
1
1
0
1
1
0
0
1
0
1
1
0
1
1
0
1
1
1
0
1
0
1
1
1
1
1
1
0
0
0
0
1
1
0
0
0
1
1
1
0
0
1
0
1
1
0
0
1
1
1
1
0
1
0
0
1
1
0
1
0
1
1
1
0
1
1
0
1
1
0
1
1
1
1
1
1
0
0
0
1
1
1
0
0
1
1
1
1
0
1
0
1
1
1
0
1
1
1
1
1
1
0
0
1
1
1
1
0
1
1
1
1
1
1
0
1
1
1
1
1
1
Philips Semiconductors
Product specification
Infrared remote control transmitter RC-5
Table 2
SAA3010
System matrix (Z-DR)
SYST. Z-LINES
NO. 0
1
2
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
June 1989
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
DR-LINES
3
4
5
6
7
0
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1
•
•
•
•
10
2
•
•
•
•
SYSTEM BITS
3
•
•
•
•
4
•
•
•
•
5
•
•
•
•
6
•
•
•
•
7
•
•
•
•
4
3
2
1
0
0
0
0
0
0
0
0
0
0
1
0
0
0
1
0
0
0
0
1
1
0
0
1
0
0
0
0
1
0
1
0
0
1
1
0
0
0
1
1
1
0
1
0
0
0
0
1
0
0
1
0
1
0
1
0
0
1
0
1
1
0
1
1
0
0
0
1
1
0
1
0
1
1
1
0
0
1
1
1
1
1
0
0
0
0
1
0
0
0
1
1
0
0
1
0
1
0
0
1
1
1
0
1
0
0
1
0
1
0
1
1
0
1
1
0
1
0
1
1
1
1
1
0
0
0
1
1
0
0
1
1
1
0
1
0
1
1
0
1
1
1
1
1
0
0
1
1
1
0
1
1
1
1
1
0
1
1
1
1
1
Philips Semiconductors
Product specification
Infrared remote control transmitter RC-5
SAA3010
Combined system mode (SSM is LOW)
The X and Z sense inputs have p-channel pull-up transistors, so that they are HIGH, until pulled LOW by connecting them
to an output as the result of a key operation. Legal operation of a key in the X-DR or Z-DR matrix will start the debounce
cycle, once key contact has been established for 18 bit-times without interruption, the oscillator enable signal is latched
and the key may be released. An interruption within the 18 bit-time period resets the device.
At the end of the debounce cycle the DR-outputs are switched off and two scan cycles are started, that switch on the
DR-lines one by one. When a Z- or X-input senses a low level, a latch enable signal is fed to the system (Z-input) or
command (X-input) latches.
After latching a system number the device will generate the last command (i.e. all command bits logic 1) in the chosen
system for as long as the key is operated. Latching of a command number causes the chip to generate this command
together with the system number memorized in the system latch. Releasing the key will reset the device if no data is to
be transmitted at the time. Once transmission has started the code will complete to the end.
Single system mode (SSM is HIGH)
In the single system mode, the X-inputs will be HIGH as in the combined system mode. The Z-inputs will be disabled by
having their pull-up transistors switched off; a wired connection in the Z-DR matrix provides the system code. Only legal
key operation in the X-DR matrix will start the debounce cycle, once key contact has been established for 18 bit-times
without interruption the oscillator enable signal is latched and the key may be released. An interruption within the
18 bit-time period resets the internal action.
At the end of the debounce cycle the pull-up transistors in the X-lines are switched off and those in the Z-lines are
switched on for the first scan cycle. The wired connection in the Z-matrix is then translated into a system number and
memorized in the system latch. At the end of the first scan cycle the pull-up transistors in the Z-lines are switched off and
the inputs are disabled again; the pull-up transistors in the X-lines are switched on. The second scan cycle produces the
command number which, after being latched, is transmitted together with the system number.
Key release detection
An extra control bit is added which will be complemented after key release; this indicates to the decoder that the next
code is a new command. This is important in the case where more digits need to be entered (channel numbers of Teletext
or Viewdata pages). The control bit will only be complemented after the completion of at least one code transmission.
The scan cycles are repeated before every code transmission, so that even with “take over” of key operation during code
transmission the right system and command numbers are generated.
Reset action
The device will be reset immediately a key is released during:
• debounce time
• between two codes.
When a key is released during matrix scanning, a reset will occur if:
• a key is released while one of the driver outputs is in the low ohmic stage (logic 0)
• a key is released before that key has been detected
• there is no wired connection in the Z-DR matrix when SSM is HIGH.
June 1989
11
Philips Semiconductors
Product specification
Infrared remote control transmitter RC-5
SAA3010
Oscillator
The OSC is the input/output for a 1-pin oscillator. The oscillator is formed by a ceramic resonator, TOKO CRK429, order
code, 2422 540 98069 or equivalent. A resistor of 6.8 kΩ must be placed in series with the resonator. The resistor and
resonator are grounded at one side.
Test
Initialization of the circuit is performed when TP1, TP2 and OSC are HIGH. All internal nodes are defined except for the
LATCH. The latch is defined when a scan cycle is started by pulling down an X- or Z-input while the oscillator is running.
If the debounce cycle has been completed, the scan cycle can be completed 3 × 23 faster, by setting TP1 HIGH.
If the scan cycle has been completed, the contents of the latch can be read 3 × 27 faster by setting TP2 HIGH.
June 1989
12
Philips Semiconductors
Product specification
Infrared remote control transmitter RC-5
SAA3010
LIMITING VALUES
Limiting values in accordance with the Absolute Maximum Rating System (IEC 134)
PARAMETER
SYMBOL
MIN.
MAX.
UNIT
Supply voltage range
VDD
−0.5
8.5
V
Input voltage range (note 1)
VI
−0.5
VDD+0.5
V
Output voltage range (note 1)
VO
−0.5
VDD+0.5
V
Input current
II
−
±10
mA
Output current
IO
−
±10
mA
OSC output
PO
−
50
mW
other outputs
PO
−
100
mW
Total power dissipation
Ptot
−
200
mW
Operating ambient temperature range
Tamb
−25
+85
°C
Storage temperature range
Tstg
−55
+150
°C
Maximum power dissipation
Note
1. VDD+0.5 V must not exceed 9.0 V.
HANDLING
Inputs and outputs are protected against electrostatic charge in normal handling, however, to be totally safe it is desirable
to take normal precautions appropriate to handling MOS devices (see “Handling MOS Devices”).
June 1989
13
Philips Semiconductors
Product specification
Infrared remote control transmitter RC-5
SAA3010
DC CHARACTERISTICS
Tamb = −25 °C to +70 °C; VDD = 2.0 to 7.0 V unless otherwise specified
PARAMETER
CONDITIONS
Supply voltage
Quiescent supply current
SYMBOL
MIN.
TYP.
MAX.
UNIT
VDD
2.0
−
7.0
V
−
−
10
µA
note 1
IDD
Tamb = 25 °C; IO = 0 mA at all
outputs; X0 to X7 and Z0 to
Z3 at VDD; TP1, TP2, OSC at
VSS SSM at VSS or VDD
INPUTS
Keyboard inputs X and Z with
p-channel pull-up transistor
Input current at each input
VI = 0 V;
TP1 = TP2 = SSM = LOW
−II
10
−
600
µA
Input voltage HIGH
note 2
VIH
0.7VDD
−
VDD
V
Input voltage LOW
note 2
VIL
0
−
0.3VDD
V
Input leakage current
Tamb = 25 °C; VI = 7 V;
TP1 = TP2 = HIGH
ILI
−
−
1
µA
Input leakage current
Tamb = 25 °C; VI = 0 V;
TP1 = TP2 = HIGH
−ILI
−
−
1
µA
Input leakage current
Tamb = 25 °C; VI = 0 V;
TP1 = TP2 = HIGH
−ILI
−
−
2
µA
Input current
Tamb = 25 °C; VI = VDD
IOSC
4.5
−
30
µA
VIH
0.7VDD
−
VDD
V
OSC
SSM, TP1, TP2
Input voltage HIGH
VIL
0
−
0.3VDD
V
Input leakage current
Tamb = 25 °C; VI = 7.0 V
ILI
−
−
1
µA
Input leakage current
Tamb = 25 °C; VI = 0 V
−ILI
−
−
1
µA
Input voltage LOW
June 1989
14
Philips Semiconductors
Product specification
Infrared remote control transmitter RC-5
PARAMETER
SAA3010
CONDITIONS
SYMBOL
MIN.
TYP.
MAX.
UNIT
Output voltage HIGH
IOH = −0.4 mA
VOH
VDD−0.3
−
−
V
Output voltage LOW
IOL = 0.6 mA
VOL
−
−
0.3
V
OUTPUTS
DATA, MDATA
VO = 7.0 V
+ILO
−
−
10
µA
VO = 7.0 V; Tamb = 25 °C
+ILO
−
−
1
µA
VO = 0 V
−ILO
−
−
20
µA
VO = 0 V; Tamb = 25 °C
−ILO
−
−
2
µA
Output voltage low
IOL = 0.3 mA
VOL
−
−
0.3
V
Output leakage current
VO = 7.0 V
+ILO
−
−
10
µA
VO = 7.0 V; Tamb = 25 °C
+ILO
−
−
1
µA
Output leakage current
DR0 TO DR7
Notes to the DC characteristics
1. Quiescent supply current measurement must be preceded by the initialization procedure described in the “Test”
section.
2. This DC test condition protects the AC performance of the output. The DC current requirements in the actual
applications are lower.
June 1989
15
Philips Semiconductors
Product specification
Infrared remote control transmitter RC-5
SAA3010
AC CHARACTERISTICS
Tamb = −25 to +85 °C; VDD = 2.0 to 7.0 V unless otherwise stated.
PARAMETER
CONDITIONS SYMBOL
Oscillator frequency
CL = 160 pF;
Figs 6 and 7
MIN.
TYP.
MAX.
UNIT
operational
fOSC
−
−
450
kHz
free-running
fOSC
10
−
120
kHz
MGE352
2
VDD
handbook, halfpage
VDD
28
OSC
X0
Z0
DR0
160 pF
handbook, halfpage
CL
18
21
normalized
frequency
(kHz)
SSM
2
8
DATA
SAA3010
1
3
17
20
14
19
TP1
TP2 VSS
VSS
MGE351
0
0
Fig.7
Fig.6 Test set-up for maximum fOSC measurement.
June 1989
16
80
160
240
320
400
CL (pF)
Typical normalized frequency as a function of
keyboard load capacitance.
Philips Semiconductors
Product specification
Infrared remote control transmitter RC-5
SAA3010
PACKAGE OUTLINES
seating plane
handbook, full
pagewidthdual in-line package; 28 leads (600 mil)
DIP28:
plastic
SOT117-1
ME
D
A2
L
A
A1
c
e
Z
w M
b1
(e 1)
b
MH
15
28
pin 1 index
E
1
14
0
5
10 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
UNIT
A
max.
A1
min.
A2
max.
b
b1
c
D (1)
E (1)
e
e1
L
ME
MH
w
Z (1)
max.
mm
5.1
0.51
4.0
1.7
1.3
0.53
0.38
0.32
0.23
36.0
35.0
14.1
13.7
2.54
15.24
3.9
3.4
15.80
15.24
17.15
15.90
0.25
1.7
inches
0.20
0.020
0.16
0.066
0.051
0.020
0.014
0.013
0.009
1.41
1.34
0.56
0.54
0.10
0.60
0.15
0.13
0.62
0.60
0.68
0.63
0.01
0.067
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
SOT117-1
051G05
MO-015AH
June 1989
EIAJ
EUROPEAN
PROJECTION
ISSUE DATE
92-11-17
95-01-14
17
Philips Semiconductors
Product specification
Infrared remote control transmitter RC-5
SAA3010
SO28: plastic small outline package; 28 leads; body width 7.5 mm
SOT136-1
D
E
A
X
c
y
HE
v M A
Z
15
28
Q
A2
A
(A 3)
A1
pin 1 index
θ
Lp
L
1
14
e
bp
0
detail X
w M
5
10 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (1)
e
HE
L
Lp
Q
v
w
y
mm
2.65
0.30
0.10
2.45
2.25
0.25
0.49
0.36
0.32
0.23
18.1
17.7
7.6
7.4
1.27
10.65
10.00
1.4
1.1
0.4
1.1
1.0
0.25
0.25
0.1
0.10
0.012 0.096
0.004 0.089
0.01
0.019 0.013
0.014 0.009
0.71
0.69
0.30
0.29
0.419
0.043
0.050
0.055
0.394
0.016
inches
0.043
0.039
0.01
0.01
Z
(1)
0.9
0.4
0.035
0.004
0.016
θ
Note
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
SOT136-1
075E06
MS-013AE
June 1989
EIAJ
EUROPEAN
PROJECTION
ISSUE DATE
95-01-24
97-05-22
18
o
8
0o
Philips Semiconductors
Product specification
Infrared remote control transmitter RC-5
Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method. Typical reflow temperatures range from
215 to 250 °C.
SOLDERING
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45 °C.
WAVE SOLDERING
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook” (order code 9398 652 90011).
Wave soldering techniques can be used for all SO
packages if the following conditions are observed:
• A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave) soldering
technique should be used.
DIP
SOLDERING BY DIPPING OR BY WAVE
• The longitudinal axis of the package footprint must be
parallel to the solder flow.
The maximum permissible temperature of the solder is
260 °C; solder at this temperature must not be in contact
with the joint for more than 5 seconds. The total contact
time of successive solder waves must not exceed
5 seconds.
• The package footprint must incorporate solder thieves at
the downstream end.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (Tstg max). If the
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
Maximum permissible solder temperature is 260 °C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150 °C within
6 seconds. Typical dwell time is 4 seconds at 250 °C.
REPAIRING SOLDERED JOINTS
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Apply a low voltage soldering iron (less than 24 V) to the
lead(s) of the package, below the seating plane or not
more than 2 mm above it. If the temperature of the
soldering iron bit is less than 300 °C it may remain in
contact for up to 10 seconds. If the bit temperature is
between 300 and 400 °C, contact may be up to 5 seconds.
REPAIRING SOLDERED JOINTS
Fix the component by first soldering two diagonallyopposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300 °C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320 °C.
SO
REFLOW SOLDERING
Reflow soldering techniques are suitable for all SO
packages.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
June 1989
SAA3010
19
Philips Semiconductors
Product specification
Infrared remote control transmitter RC-5
SAA3010
DEFINITIONS
Data sheet status
Objective specification
This data sheet contains target or goal specifications for product development.
Preliminary specification
This data sheet contains preliminary data; supplementary data may be published later.
Product specification
This data sheet contains final product specifications.
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.
June 1989
20