SUBMINIATURE T-3/4 LED DIFFUSED and CLEAR LAMPS HIGH EFF. RED YELLOW GREEN AIGaAs RED HLMP-6305A HLMP-6405A HLMP-6505A HLMP-Q105A Water Water Water Water Clear Clear Clear Clear MV6700A MV6300A MV6400A HLMP-Q150A PACKAGE DIMENSIONS .276 (7.0) MIN .087 (2.2) .079 (2.0) DESCRIPTION The QT Optoelectronics family of T-3/4 subminiature LED lamps feature a square-base, transfer molded package for surface mount applications. A tinted diffused or water clear epoxy lens — available in AIGaAs red, high-efficiency red, green, and yellow — produces wide-angle beam emission and sharp on/off contrast. The LEDs are offered with gullwing lead bends for top mounting, as well as yoke lead bends and Z-bends for mounting to the back of a PCB. .276 (7.0) MIN .020 (.5) .012 (.3) .024 (.6) .016 (.4) .091 (2.3) .083 (2.1) .075 (1.9) DIA .063 (1.6) Diffused Diffused Diffused Diffused .058 (1.48) .050 (1.28) FEATURES .031 (.78) .023 (.58) ■ ■ ■ CATHODE MARK NOTE: .010 (.26) .002 (.06) ■ .056 (1.44) .048 (1.24) ■ Subminiature T-3/4 transfer molded Low package profile Axial leads Wide viewing angle SMT versions CATHODE MARK 1. ALL DIMENSIONS ARE IN INCHES (mm) PHYSICAL CHARACTERISTICS TYPE SOURCE COLOR LENS COLOR HLMP-6305A High Efficiency Red Water Clear HLMP-6405A Yellow Water Clear HLMP-6505A Green Water Clear HLMP-Q105A AIGaAs Red Water Clear MV6700A High Efficiency Red Red Diffused MV6300A Yellow Yellow Diffused MV6400A Green Green Diffused AIGaAs Red Red Diffused HLMP-Q150A SUBMINIATURE T-3/4 LED DIFFUSED and CLEAR LAMPS ABSOLUTE MAXIMUM RATING (TA = 25° C Unless otherwise specified) PARAMETER HLMP-6305A MV6700A HLMP-6405A MV6300A HLMP-6505A MV6400A HLMP-Q105A HLMP-Q150A UNITS Power dissipation 135 85 135 85 mW Average forward current 30 20 30 30 mA Peak forward current (1mS pulsewidth, 0.1% DF) 90 60 90 300 mA Lead soldering time at 260° C 3 3 3 3 sec Operating temperature -55 to 100 -55 to 100 -55 to 100 -20 to 100 °C Storage temperature -55 to 100 -55 to 100 -55 to 100 -55 to 100 °C ELECTRO-OPTICAL CHARACTERISTICS (TA = 25° C Unless otherwise specified) PART NUMBER QTLP- MV6700A MV6300A MV6400A HLMPQ150A Luminous intensity (mcd) TEST CONDITIONS IF = 10 mA minimum 1.0 1.0 1.0 1.0* typical 3.0 3.0 3.0 1.8* Forward voltage (V) IF = 10 mA minimum 1.5 1.5 1.5 typical 1.8 2.0 2.0 1.6* maximum 3.0 3.0 3.0 1.8* Peak wavelength (nm) 635 583 570 660 Spectral line half width (nm) 40 36 28 20 Reverse voltage (V) 5 5 5 5 Viewing angle (°) 50 50 28 50 *Tested at IF = 1 mA IR =100 mA ELECTRO-OPTICAL CHARACTERISTICS (TA = 25° C Unless otherwise specified) PART NUMBER QTLP- HLMP6305A HLMP6405A HLMP6505A HLMPQ105A Luminous intensity (mcd) minimum typical TEST CONDITIONS IF = 10 mA 3.0 3.0 3.0 20.0* 12.0 12.0 12.0 50.0* Forward voltage (V) IF = 10 mA minimum 1.5 1.5 1.5 typical 1.8 2.0 2.0 1.8* maximum 3.0 3.0 3.0 2.4* Peak wavelength (nm) 635 583 570 660 Spectral line half width (nm) 40 36 28 20 Reverse voltage (V) 5 5 5 5 Viewing angle (°) 25 25 25 25 *Tested at IF = 20 mA IR =100 mA SUBMINIATURE T-3/4 LED DIFFUSED and CLEAR LAMPS TYPICAL ELECTRO-OPTICAL CHARACTERISTIC CURVES (TA = 25° C) AIGaAs RED 40 90 80 H-E RED YELLOW 70 GREEN 60 50 40 30 LUMINOUS INTENSITY PEAK FORWARD CURRENT IF (mA) 100 30 YELLOW GREEN H-E RED 20 10 20 10 0 0 1 2 3 0 4 FORWARD VOLTAGE VF (VOLTS) 20 40 60 80 INSTANTANEOUS FORWARD CURRENT IF (mA) FIG. 1 - Forward Current vs. Forward Voltage FIG. 2 - Luminous Intensity vs. Forward Current GREEN H-E RED YELLOW AIGaAs RED 300.0 200.0 100.0 50.0 100% RELATIVE OUTPUT IF — FORWARD CURRENT — mA 120% 20.0 10.0 5.0 2.0 1.0 .5 80% 60% 40% 20% .2 .1 0 .5 1.0 1.5 2.0 2.5 3.0 3.5 VF — FORWARD VOLTAGE — V FIG. 3 - Forward Current vs. Forward Voltage—AIGaAs 0% 520 540 560 580 600 620 640 660 680 700 WAVELENGTH (l) — nm FIG. 4 - Spectral Distribution SUBMINIATURE T-3/4 LED DIFFUSED and CLEAR LAMPS OPTIONAL CONFIGURATIONS PACKAGE DIMENSIONS DESCRIPTION GULLWING LEAD CONFIGURATION .087 (2.2) .079 (2.0) ANODE CATHODE .020 (.5) .012 (.3) .024 (.6) .016 (.4) Automatic placement equipment can be used to mount the LEDs on the PC board. The lamps can be mounted using either batch or in line vapor phase reflow solder processes. .091 (2.3) .083 (2.1) .154 (3.90) .148 (3.75) These subminiature solid state lamps are transfer molded in an axial lead package. They are available in yellow, green, high efficiency red and AIGaAs red in both diffused and water clear lens. FEATURES .058 (1.48) .050 (1.28) .039 (1.0) .028 (.7) ■ ■ CATHODE ■ .010 (.26) .002 (.06) ■ .033 (.82) .000 (.00) .016 (.4) .008 (.2) ■ .078 (1.9) .063 (1.6) Available in Gullwing, Yoke and Z-bend lead formings Compatible with automatic placement equipment Compatible with vapor phase reflow soldering processes Long life — solid state reliability Reel and tape or bulk packaging available NOTE: ALL DIMENSIONS ARE IN INCHES (mm) .115 (2.92) .099 (2.52) CATHODE MARK Z-BEND LEAD CONFIGURATION .240 (1.6) .232 (5.9) YOKE LEAD CONFIGURATION .087 (2.2) .079 (2.0) CATHODE .020 (.5) .012 (.3) .020 (.5) .012 (.3) .024 (.6) .016 (.4) .024 (.6) .016 (.4) ANODE ANODE .091(2.3) .083 (2.1) .300 (7.62) MAX .047 (1.2) .031 (0.8) .010 (.26) .002 (.06) .048 (1.22) .032 (.82) .087 (2.2) .079 (2.0) CATHODE .189 (4.8) .173 (4.4) CATHODE .033 (.85) .026(.65) .034 (.86) .026 (.66) .010 (.26) .002 (.06) CATHODE .033 (.85) .026 (.65) .091 (2.3) .083 (2.1) .039 (.99) .023 (.59) .117 (2.96) .100 (2.56) .128 (3.24) .112 (2.84) CATHODE .078 (1.9) .063 (1.6) .115 (2.92) .099 (2.52) .058 (1.48) .050 (1.28) .058 (1.48) .050 (1.28) .078 (1.9) .063 (1.6) CATHODE MARK Call QT Optoelectronics for more information or the phone number of your nearest distributor. United States 800-533-6786 France 33 01/43.99.25.12 Germany 49 089/96.30.51 United Kingdom 44 01296/39.44.99 Asia/Pacific 603/735-2417 ■ © 1996 QT Optoelectronics QT-009-A ■ ■ ■ DS 100