SPECIFICATIONS No. STK442-090 2000.04.18 TENTATIVE 1. Case Outline 14Pins (See attached outline drawing) 2. Function class AB 2 channels AF power amplifier 3. Application 50W audio use 4. Maximum Ratings / Ta=25deg Item Power Supply Voltage 1 Power Supply Voltage 2 Thermal Resistance Junction Temperature Operating Substrate Temperature Storage Temperature Available Time for Load Short-circuit *4 Symbol Conditions Vcc max(1) No signal Vcc max(2) Signal ,R L=8ohm ,6ohm Theta j-c Per one power TR Tj max Tc max Tstg Vcc=+-35V,RL=6ohm,f=50Hz ts PO=50W,1ch drive 5. Operating Characteristics Tc=25deg,RL=6ohm(Non-inductive Load),Rg=600ohm,VG=30dB Conditions *2 Item Symbol V f Po THD MIN. (V) (Hz) (W) (%) Po1 +-35 20 to 20k 0.4 50 Output Power *1 Po2 +-35 1k 10 THD *1 Frequency Characteristics *1 Input Impedance Output Noise Voltage Quiescent Current Output Neutral Voltage *3 THD +-35 20 to 20k 50 fL,fH +-35 1.0 ri +-35 VNO +-42 ICCO +-42 VN +-42 1k +0 -3 dB 1.0 Ratings +-54 +-47 2.2 150 125 -30 to +125 Unit V V deg/W deg deg deg 0.3 s Ratings TYP. Unit W 80 0.2 % 20 to 50k Hz 55 kohm Rg=2.2 kohm -70 MAX. 0 1.0 mVrms 80 mA +70 mV *Specifications and information herein are subject to change without notice. Note *1.1ch Drive *2.All tests are measured using a constant-voltage supply unless otherwise specified. *3.The output noise voltage is peak value of an average-reading meter with a rms value scale(VTVM). A regulated AC supply(50Hz) should be used to eliminate the effects of AC primary line flicker noise. *4.Available time for load short-circuit and output noise voltage are measured using the specified transformer power supply. Specified Transformer Power Supply DBA40C 10000u +Vcc + 500ohm + 500ohm -Vcc 10000u (Equivalent to MG-200) Sanyo Electric Co.,Ltd. Module Systems Division NO.1 Equivalent Block Diagram 1 9 C10 TR1 TR2 D2 C11 D3 R3 R13 TR6 TR19 C1 TR8 TR3 TR18 R4 TR4 11 TR10 TR14 TR13 TR20 13 R15 R6 14 R14 R5 TR5 C5 R18 C2 10 TR11 TR16 TR9 R8 C4 TR12 TR7 TR17 R16 C7 D1 R2 TR15 C8 R17 R7 R12 2 SUB 3 12 8 5 4 7 6 Test Circuit +Vcc -Vcc SUB Ch1 +RE Ch1 -RE Ch2 -RE 1 2 3 4 5 6 (*1) (*1) Ch2 +RE -PRE 7 (*1) 8 +PRE 9 Ch1 IN Ch1 NF BIAS Ch2 NF 10 11 12 13 220pF (*1) Ch2 IN 14 220pF 56kohm 100uF /100v 100uF /100v 470pF 1kohm 470pF 56kohm 56kohm 2.2uF 3uH /50v 100ohm/1W +Vcc 100uF /10v 1.8kohm 100uF /10v 3pF 1.8kohm 2.2uF /50v 20kohm 56kohm 3pF Ch2 IN GND Ch1 IN 1kohm Ch2 OUT 0.1uF 4.7ohm GND 4.7ohm/1W GND 100uF /100v 100uF /100v 4.7ohm/1W 3uH -Vcc 100ohm/1W 0.1uF Ch1 OUT 4.7ohm SUB.GND (*1)Metal Plate Cement Resistor 0.22ohm+-10%(5W) No.2 Case Outline Unit:mm * No production described or contained herein are intended for use in surgical implants, life-support systems, aerospace equipment, nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure, of which may directly or indirectly cause injury, death or property loss * Anyone purchasing any products described or contained herein for an above-mentioned use shall: 1. Accept full responsibility and indemnify and defend SANYO ELECTRIC CO.,LTD., its affiliates, subsidiaries and distributors and all their officers and employees, jointly and severally, against any and all claims and litigation and all damage, cost and expenses associated with such use: 2. Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on SANYO ELECTRIC CO.,LTD., its affiliates, subsidiaries and distributors or any of their officers and employees jointly or severally. * Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not guaranteed for volume production. SANYO believes its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of April,2000. Specifications and information herein are subject to change without notice. No.3