SN74ALVCH16827 20-BIT BUFFER/DRIVER WITH 3-STATE OUTPUTS SCES041C – JULY 1995 – REVISED FEBRUARY 1999 D D D D D D DGG OR DL PACKAGE (TOP VIEW) Member of the Texas Instruments Widebus Family EPIC (Enhanced-Performance Implanted CMOS) Submicron Process ESD Protection Exceeds 2000 V Per MIL-STD-883, Method 3015; Exceeds 200 V Using Machine Model (C = 200 pF, R = 0) Latch-Up Performance Exceeds 250 mA Per JESD 17 Bus Hold on Data Inputs Eliminates the Need for External Pullup/Pulldown Resistors Package Options Include Plastic 300-mil Shrink Small-Outline (DL) and Thin Shrink Small-Outline (DGG) Packages 1OE1 1Y1 1Y2 GND 1Y3 1Y4 VCC 1Y5 1Y6 1Y7 GND 1Y8 1Y9 1Y10 2Y1 2Y2 2Y3 GND 2Y4 2Y5 2Y6 VCC 2Y7 2Y8 GND 2Y9 2Y10 2OE1 description This 20-bit noninverting buffer/driver is designed for 1.65-V to 3.6-V VCC operation. The SN74ALVCH16827 is composed of two 10-bit sections with separate output-enable signals. For either 10-bit buffer section, the two output-enable (1OE1 and 1OE2 or 2OE1 and 2OE2) inputs must both be low for the corresponding Y outputs to be active. If either output-enable input is high, the outputs of that 10-bit buffer section are in the high-impedance state. To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. 1 56 2 55 3 54 4 53 5 52 6 51 7 50 8 49 9 48 10 47 11 46 12 45 13 44 14 43 15 42 16 41 17 40 18 39 19 38 20 37 21 36 22 35 23 34 24 33 25 32 26 31 27 30 28 29 1OE2 1A1 1A2 GND 1A3 1A4 VCC 1A5 1A6 1A7 GND 1A8 1A9 1A10 2A1 2A2 2A3 GND 2A4 2A5 2A6 VCC 2A7 2A8 GND 2A9 2A10 2OE2 Active bus-hold circuitry is provided to hold unused or floating data inputs at a valid logic level. The SN74ALVCH16827 is characterized for operation from –40°C to 85°C. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. EPIC and Widebus are trademarks of Texas Instruments Incorporated. Copyright 1999, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN74ALVCH16827 20-BIT BUFFER/DRIVER WITH 3-STATE OUTPUTS SCES041C – JULY 1995 – REVISED FEBRUARY 1999 FUNCTION TABLE (each 10-bit section) INPUTS OUTPUT Y OE1 OE2 A L L L L L L H H H X X Z X H X Z logic symbol† 1OE1 1OE2 2OE1 2OE2 1A1 1A2 1A3 1A4 1A5 1A6 1A7 1A8 1A9 1A10 2A1 2A2 2A3 2A4 2A5 2A6 2A7 2A8 2A9 2A10 1 & EN1 56 28 & EN2 29 55 1 1 54 3 52 5 51 6 49 8 48 9 47 10 45 12 44 13 43 14 42 1 2 15 41 16 40 17 38 19 37 20 36 21 34 23 33 24 31 26 30 27 † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. 2 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1Y1 1Y2 1Y3 1Y4 1Y5 1Y6 1Y7 1Y8 1Y9 1Y10 2Y1 2Y2 2Y3 2Y4 2Y5 2Y6 2Y7 2Y8 2Y9 2Y10 SN74ALVCH16827 20-BIT BUFFER/DRIVER WITH 3-STATE OUTPUTS SCES041C – JULY 1995 – REVISED FEBRUARY 1999 logic diagram (positive logic) 1 1OE1 1OE2 1A1 28 2OE1 2OE2 56 55 2 1Y1 2A1 29 42 To Nine Other Channels 15 2Y1 To Nine Other Channels absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 4.6 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 4.6 V Output voltage range, VO (see Notes 1 and 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Continuous output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA Continuous current through each VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±100 mA Package thermal impedance, θJA (see Note 3): DGG package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81°C/W DL package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. This value is limited to 4.6 V maximum. 3. The package thermal impedance is calculated in accordance with JESD 51. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 SN74ALVCH16827 20-BIT BUFFER/DRIVER WITH 3-STATE OUTPUTS SCES041C – JULY 1995 – REVISED FEBRUARY 1999 recommended operating conditions (see Note 4) VCC Supply voltage VIH High-level input voltage VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 2.7 V to 3.6 V MIN MAX 1.65 3.6 2 0.35 × VCC Low-level input voltage VI VO Input voltage 0 Output voltage 0 0.7 VCC = 2.7 V to 3.6 V IOL ∆t/∆v High level output current High-level VCC = 2.7 V VCC = 3 V VCC = 1.65 V VCC = 2.3 V Low level output current Low-level VCC = 2.7 V VCC = 3 V Input transition rise or fall rate V 1.7 VIL IOH V 0.65 × VCC VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 1.65 V VCC = 2.3 V UNIT V 0.8 VCC VCC V V –4 –12 –12 mA –24 4 12 12 mA 24 10 ns/V TA Operating free-air temperature –40 85 °C NOTE 4: All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN74ALVCH16827 20-BIT BUFFER/DRIVER WITH 3-STATE OUTPUTS SCES041C – JULY 1995 – REVISED FEBRUARY 1999 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS VCC 1.65 V to 3.6 V IOH = –100 µA IOH = –4 mA 1.65 V IOH = –6 mA VOH IOH = –12 mA IOH = –24 mA IOL = 100 µA IOZ ICC ∆ICC Ci Data inputs 2 2.3 V 1.7 UNIT 2.7 V 2.2 3V 2.4 3V 2 V 0.2 2.3 V 0.4 2.3 V 0.7 2.7 V 0.4 3V 0.55 ±5 3.6 V VI = 0.58 V VI = 1.07 V 1.65 V 25 1.65 V –25 VI = 0.7 V VI = 1.7 V 2.3 V 45 2.3 V –45 VI = 0.8 V VI = 2 V 3V 75 3V –75 V µA µA VI = 0 to 3.6 V‡ 3.6 V ±500 VO = VCC or GND VI = VCC or GND, 3.6 V ±10 µA 3.6 V 40 µA 750 µA IO = 0 Other inputs at VCC or GND One input at VCC – 0.6 V, Control inputs 2.3 V 0.45 IOL = 24 mA VI = VCC or GND II(hold) ( ) MAX VCC–0.2 1.2 1.65 V IOL = 12 mA II TYP† 1.65 V to 3.6 V IOL = 4 mA IOL = 6 mA VOL MIN 3 V to 3.6 V VI = VCC or GND 3.5 33V 3.3 pF 6 Co Outputs VO = VCC or GND 3.3 V 7.5 pF † All typical values are at VCC = 3.3 V, TA = 25°C. ‡ This is the bus-hold maximum dynamic current. It is the minimum overdrive current required to switch the input from one state to another. switching characteristics over recommended operating free-air temperature range (unless otherwise noted) (see Figures 1 through 3) PARAMETER tpd VCC = 1.8 V FROM (INPUT) TO (OUTPUT) A Y TYP § ten OE Y § tdis OE Y § VCC = 2.5 V ± 0.2 V MIN MAX 1 VCC = 2.7 V MIN VCC = 3.3 V ± 0.3 V UNIT MAX MIN MAX 4.1 3.9 1 3.4 ns 1 6 5.7 1 4.7 ns 1.2 5.6 4.9 1.3 4.5 ns § This information was not available at the time of publication. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 SN74ALVCH16827 20-BIT BUFFER/DRIVER WITH 3-STATE OUTPUTS SCES041C – JULY 1995 – REVISED FEBRUARY 1999 operating characteristics, TA = 25°C PARAMETER Outputs enabled Power dissipation capacitance Cpd d VCC = 1.8 V TYP † TEST CONDITIONS CL = 50 pF, pF Outputs disabled f = 10 MHz VCC = 2.5 V TYP VCC = 3.3 V TYP 16 18 4 6 † UNIT pF † This information was not available at the time of publication. PARAMETER MEASUREMENT INFORMATION VCC = 1.8 V 2 × VCC S1 1 kΩ From Output Under Test Open GND CL = 30 pF (see Note A) 1 kΩ TEST S1 tpd tPLZ/tPZL tPHZ/tPZH Open 2 × VCC GND LOAD CIRCUIT tw VCC Timing Input VCC/2 VCC/2 VCC/2 0V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VCC/2 VCC/2 0V tPLH Output Control (low-level enabling) VCC/2 0V Output Waveform 1 S1 at 2 × VCC (see Note B) tPLZ VCC VCC/2 VOL + 0.15 V VOL tPHZ tPZH tPHL VOH VCC/2 VCC VCC/2 tPZL VCC Input VOLTAGE WAVEFORMS PULSE DURATION th VCC Data Input VCC/2 0V 0V tsu Output VCC VCC/2 Input VCC/2 VOL Output Waveform 2 S1 at GND (see Note B) VCC/2 VOH VOH – 0.15 V 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2 ns, tf ≤ 2 ns. D. The outputs are measured one at a time with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. Figure 1. Load Circuit and Voltage Waveforms 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN74ALVCH16827 20-BIT BUFFER/DRIVER WITH 3-STATE OUTPUTS SCES041C – JULY 1995 – REVISED FEBRUARY 1999 PARAMETER MEASUREMENT INFORMATION VCC = 2.5 V ± 0.2 V 2 × VCC S1 500 Ω From Output Under Test Open GND CL = 30 pF (see Note A) 500 Ω TEST S1 tpd tPLZ/tPZL tPHZ/tPZH Open 2 × VCC GND LOAD CIRCUIT tw VCC Timing Input VCC/2 VCC/2 VCC/2 0V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VCC/2 VCC/2 0V tPLH Output Control (low-level enabling) VCC/2 0V Output Waveform 1 S1 at 2 × VCC (see Note B) tPLZ VCC VCC/2 VOH VCC/2 VOL Output Waveform 2 S1 at GND (see Note B) VOL + 0.15 V VOL tPHZ tPZH tPHL VCC/2 VCC VCC/2 tPZL VCC Input VOLTAGE WAVEFORMS PULSE DURATION th VCC Data Input VCC/2 0V 0V tsu Output VCC VCC/2 Input VCC/2 VOH VOH – 0.15 V 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2 ns, tf ≤ 2 ns. D. The outputs are measured one at a time with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. Figure 2. Load Circuit and Voltage Waveforms POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 SN74ALVCH16827 20-BIT BUFFER/DRIVER WITH 3-STATE OUTPUTS SCES041C – JULY 1995 – REVISED FEBRUARY 1999 PARAMETER MEASUREMENT INFORMATION VCC = 2.7 V AND 3.3 V ± 0.3 V 6V S1 500 Ω From Output Under Test GND CL = 50 pF (see Note A) TEST S1 tpd tPLZ/tPZL tPHZ/tPZH Open 6V GND Open 500 Ω tw LOAD CIRCUIT 2.7 V 2.7 V Timing Input 1.5 V Input 1.5 V 0V 1.5 V 0V tsu VOLTAGE WAVEFORMS PULSE DURATION th 2.7 V Data Input 1.5 V 1.5 V 0V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES 2.7 V Output Control (low-level enabling) 1.5 V 1.5 V 0V tPLZ tPZL 2.7 V Input 1.5 V 1.5 V 0V tPLH 1.5 V 3V 1.5 V tPZH tPHL VOH Output Output Waveform 1 S1 at 6 V (see Note B) 1.5 V VOL Output Waveform 2 S1 at GND (see Note B) 1.5 V VOL + 0.3 V VOL tPHZ VOH VOH – 0.3 V 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. D. The outputs are measured one at a time with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. Figure 3. Load Circuit and Voltage Waveforms 8 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 1999, Texas Instruments Incorporated