SHARP PCSOOV

DATE:
PREPARED BY:
SHAR
ELECTRONIC
COMPONENTS
GROUP SHARP CORPORATION
SPECIFICATION
f
DEVICE
SPECIFICATION
I OPTO-ELECTRONIC
-+=%An
DEVI
FOR
PHOTOCOUPLER
I
MODEL
No.
PCSOOV
(Businessdealingname:
1. These specification
sheets include materfals protected
Please do not reproduce or cause anyone to reproduce
PC9OOVONSZXl
under copyright of Sharp Corporation
them without Sharp’s consent.
(“Sharp”).
-
2. When using this product, please observe the absolute maximum ratings and the instructions
for use outlIned
in these specification
sheets, as well as the precautions
mentioned below. Sharp assumes no responsibility
for any damage resulting from use of the product which does not comply with the absolute maximum ratings
and the instructions
included in these specification
sheets, and the precautions menttoned below.
(Precautions)
(1) This product is designed for use in the following application
areas ;
* Audio visual equipment
* Home appliances
OA equipment
* Measuring equipment
- Telecommunication
equipment (Terminal)
*
Tooling
machines
Computers
i
If the use of the product in the above application
areas is for equipment listed in paragraphs
(2) or (3). please be sure to observe the precautions
gtven in those respective paragraphs.
1
l
(2) Appropriate
measures, such as fail-safe design and redundant
design considering
the safety design of the overall system and equipment,
should be taken to ensure reliability
and safety when this product is used for equipment which demands high reliability and
safety in function and precision, such as ;
* Transportation
control and safety equipment (aircraft, train. automobile
- Traffic sigmk
* Gas leakage sensor breakers
* Rescue and security
*
Other
safety
equipment
[
etc.)
equipment
I
[3) Please do not use this product for equipment which require extremely high reliability
and safety in function and precision, such as :
* Space equipment
* Telecommunication
equipment (for trunk lines)
Nuclear
power
control
equipment
*
Medical
equipment
[
1
l
(4) Please contact and consult with a Sharp sales representative
regarding interpretation
of the above three paragraphs.
3. Please contact
and consult
with a Sharp sales
representative
if there are any questions
for any questions
about this product.
F J-p.
CUSTOMER’S
DATE
BY
APPROVAL
DATE
PRESENTED
BY
IJ,
,+a-3
J
/G&‘&&h
K. Hachimura,
Department
General Manager
Engineering
Dept. .I1
Opto-Electronic
Devices Div.
ELECOM
Group
SHARP CORPORATION
of
SHRRP CORPORATI ON
1. Application
This specification applies to the outline and characteristics
Model No. PCSOOV.
of photocoupler
2. Outline
Refer to the attached sheet. page 3.
3. Ratings and characteristics
Refer to the attached sheet, page 3 to 5.
4. Reliability
Refer to the attached
sheet, page 8.
5. Outgoing inspection
Refer to the attached sheet. page 9.
6. Supplement
6.1 Isolation voltage shall be measured in the following method.
(I) Short among pins 1 to 3 on the primary side and among pins 4 to 6 on
the secondary side.
(2) The dielectric withstand
tester with zero-cross circuit shall be used.
(3) The wave form of applied voltage shall be a sine wave.
(It is recommended that the isolation voltage be measured in insulation
oil.)
6.2 The business dealing name used for this product when ordered or delivered shall be
PCSOOVONSZX.
6.3 Package specifications
Refer to the attached sheets-2- 1 to 2-3.
SHARP CORPORATION
6.4 UL : Under preparation
6.5 Theory of operation
(1) When the forward current of above the “H+L” threshold input current (Ir,.J
is applied to the input side, the output will go “Low level”.
(2) When the forward current on the input side goes below the “L+H” threshold
input current (I,,,) is applied to the input side, the output will go “High level”.
6.6 This product is not designed against irradiation.
This product is assembled with electrical input and output.
This product incorporates
non-coherent
-
light emitting,diode.
6.7 ODS materials
This product shall not contain the following materials.
Also, the following materials shall not be used in the production
Materials
6.8 Brominated
process for this product.
for ODS : CFC, Halon, Carbon tetrachloride.
1.1.1 -Trichloroethane
(Methylchloroform)
flame retardants
Specific brominated flame retardants
in this device at all.
7. Notes
Refer to the attached sheet-l- 1. 2.
such as the PBBOs and PBB, are not used
SHARP CORPORATION
2. Outline
7.12zto.3
m
?I
m
cd
regulator
Anode inai
Anode
\
Lot No. ‘1
Cathode
N. c
Pin NOS. and inter!‘Ial
connection diagram
7.629~0.3
l
l
2.54&O.
*l)
2-digit number
25
0.5fO.
1
shall be marked according to
DIN
standard.
*2) Marking is laser marking
UNIT:
Product mass : Approx. 0.36g
Name
l/l
mm
PCSOOV
Outline Dimensions
(Business dealing
name : PC9OOVONSZX)
SHARP CORPORflTION
Ratings and characteristics
3.1 Absolute maximum
*l
ratings
The derating factors of absolute maximum
are shown in Fig. 1, 2. 3.
*2 Pulse widths
100 ps, Dutyratio
*3 AC for 1 min, 40 to 6O%RH
*4 ForlOs
: 0.001
ratings due to ambient temperature
SHARP CORPORATION
3.2 Electra-optical
characteristics
Parameter
-GIN.
1 TYP. 1 MAX. 1 Unit 1
Conditions
Forward voltage
Reverse current
Terminal capacitance
Operating
range
supply voltage
IR
I
-
1
-
Ct
(
-
I30
1 10
1 PA 1 Ta=25%, V,=3V
1250
1 ,,(~;25;,V=O
vcc
131
Low level output voltage
VOL
1
-
1 0.2
1 0.4
High level output
bH
1
-
1
1 100 1 PA 1 g$=l5V
Low level supply current
bcL
1
-
1 2.5
1 5.0
1 mA 1 Vcc=5V, 1,=4mA
High level supply current
ECH
I
-
1 1.0 1 5.0
1 mA 1 Vcc=5”, I,=OmA
1 0.7
1 0.9
1
1
1 R
current
“H-L” threshold
current *l
input
“L-H” threshold
current *2
input
Hysteresis
*3
‘FLH /IF,,
Isolation resistance
“H-L”
propagation
Rho
time
-1151vI
1 0.5
I5XlO’Ol
-
10”
_
-
tPHL
1
3
t PLH
2
6
0.05
0.5
0.1
0.5
1 v
-
1 ~&6!&nA,Vcc=5”
1 vcc=5v,
Iq=280Q
( T$..~ox$OOV
Ta=25%
“L-H”
propagation
time
vcc=5v.
Fall time
tf
Rise time
tr
-
R,=280 0
1,=4mA
-”
SHflRP
CORPORATION
*1 I,,
represents forward current when output goes from “H” to “L”.
”
represents forward current when output goes from “L” to “H”.
‘FLH
‘3 Hysteresis : IFLH/IFHL
*4 Test circuit for response time shall be shown below.
Vobge regulator
tr==tt-0.0
.?0=50n
output
Test circuit diaffram
Timing chart
SHARP CORPORATION
(Fig. 2) Output powe
vs. ambient temperature’-
(Fig. 1) Forward current vs.
ambient temperature
$
g
-50
$
2
z
g
2
3
2
g
8
40
30
20
b3
100
10
“a
x
50
5
0
0
-25
0
25
50
7585
Ambient temperature
100
125
5
E
tz 200
13 170
g 150
3
2
‘El
b 100
50
-25
0
25
50
Ambient temperature
7585
100
Ta (‘C)
0
-25
0
25
50
Ambient temperature
Ta (‘c)
(Fig. 3) Total power dissipation
vs. ambient temperature
3
ifi
250
125
7585
Ta (‘C)
100 125
!
SHARP CORPOR~ITION
4. Reliability
The reliability
of products shall be satisfied with items listed below.
Confidence level : 90%
LTPD : 10%/20%
Test Items
Test Conditions
‘1
Solderability
Soldering
*2
heat
Failure Judgement
Criteria
230%. 5 s
260%. 10 s
v,>ux
Terminal strength
(Tension)
Weight : 5N
5 s/each terminal
I,>UX2
Terminal strength
(Bending) *3
Weight : 2.5N
2 times/each terminal
Mechanical
15km/s’, 0.5ms
3 times/fX.
+-Y, fZ direction
1.2
vo,>ux1.2
shock
Samples In)
Defective(C)
n=ll,
C=O
n=ll.
C=O
n=ll.
C=O
n=ll,
C=O
n=ll,
C=O
n=ll.
C=O
- r
I,,>UX1.2
ICCL>UX 1.2
IccH>ux 1.2
Variable frequency
vibration
100 to 2000 to lOOHz/4min
200m/sZ
4 times/ X. Y. Z direction
Temperature
cycling
1 cycle -40% to +125%
(30min) (30min)
20 cycles test
High temp. and high
humidity storage
+85C. 85%RH. lOOOh
High temp. storage
+ 125%. lOOOh
Low temp. storage
-40%. 1OOOh
Operation
I,= 1OmA, vcc= 15v
&= 16mA, Ta=25%. 1OOOh
I,,,>UX1.3
I,,<LXO.7
life
* 1 Test method, conforms to EW
n=22,C=O
lFLH /‘FHL~;“x;-“2
n=22,C=O
U : Upper
specification
limit
L : Lower
specification
limit
ED 470 1.
*2 Solder shall adhere at the area of 95% or more of immersed portion of
lead, and pin hole or other holes shall not be concentrated on one portion.
+3 Terminal
bending direction
is shown below.
m
k-f5
6
’
n=22,C=O
n=22,C=O
n=22,C=O
SHARP CORPOMTION
5. Outgoing inspection
5.1 Inspection
items
(1) Electrical characteristics
v,
I,. v,,.
&.
ICC/ ICCH’ I,,.
IiqJ+.Rise. visa
(2) Appearance
5.2 Sampling method and Inspection level
A single sampling plan. normal inspection level II based on
IS0 2859 is applied. The AQL according to the inspection
items are shown below.
Defect
Inspection
item
AQL WI
Major
defect
Electrical characteristics
Unreadable marking
0.065
Minor
defect
Appearance defect except
the above mentioned.
0.25
SHflRP CORPORATION
Precautions
for Photocouplers
1 For cleaning
(1) Solvent cleaning : Solvent temperature 45% or less
Immersion for 3 min or less
(2) Ultrasonic
cleaning : The effect to device by ultrasonic cleaning differs
by cleaning bath size, ultrasonic power
output, cleaning time, PCB size or device mounting
condition etc. Please test it in actual using condition
and con&n that doesn’t occur any defect before starting
the ultrasonic cleaning.
(3) Applicable
solvent : Ethyl alcohol, Methyl alcohol, Isopropyl alcohol
In case when the other solvent is used. there are cases that
the packaging resin is eroded. Please use the other solvent
after thorough coniirmation is performed in actual using condition.
2. Please use the same as normal integration circuit about static
electricity in order that this device is OPIC photocoupler.
3. In order to stabilize power supply line. we recommend to connect
a by-pass capacitor of 0.0 1 p F or more between Vcc and GND near the device.
4. The detector which is used in this device, has parasitic diode between each pins and GND.
There are cases that miss operation or destruction possibly may be occurred if electric
potential of any pin becomes below GND level even for instant.
Therefore it shall be recommended to design the circuit that electric potential of
any pin does not become below GND level.
5. The LED used in the Photocoupler generally decreases the light emission power
by operation. In case of long operation time, please design the circuit with considering
the decreases of the light emission power of the LED. (500/6/5years)
Please decide the input current which become 2 times of MAX. I,,,
SHARP CORPORATION
6. Precautions
for Soldering Photocouplers
An example of device temperature
vs. soldering time
(1) In case of soldering
to lead
260% 10 s or less
180
160
140
120
Device
temperature
(Cl
-
.#
ed
.*-
-0
*-
*- e--
go -
20
0’
Solder
-
0
’
2
’
4
I
1 I
1
6’ 8 10 12 14 16 18 20
Soldering time (s)
(2) If solder reflow :
It is recommended that only one soldering be done at the temperature
and the time within the temperature profile as shown in the figure below.
230C
18OC
25C
(3) Other precautions
An infrared lamp used to heat up for soldering may cause a localized
temperature rise in the resin. So keep the package temperature within
that specified in Item (2). Also avoid immersing the resin part in the solder.
SHflRP
CORPORATION
Package specification
1 Package materials
No.
Materials
Name
PUrpOSeS
1
Sleeve
Plastfcs with preventing
static electricity
Products packaged
2
Stopper
Rubber
Products tied
3
Packing case
Corrugated
4
Kraft tape
Paper
Lid of packaged case fixed
-
5
Label
Paper
Model No., quantity,
inspection date and lot No.
specified
cardboard
Sleeve packaged
2 Package method
(1) MAX. 5Opcs. of products shall be packaged in a sleeve and
both of sleeve edges shah be fixed by stoppers.
(2) MAX. 20 sleeves above shall be packaged in a packing case
and pack a sheet of cushion at one side.
(3) Model No., quantity, inspection date and lot No. shall be marked on the label
and this label shall be put on the side of the packaging case.
(4) Case shall be closed with the lid and enclosed with kraft tape.
3 Package outline dimensions
(1) Sleeve outline dimensions
Refer to the attached
sheets-2-2.
(2) Packaging case outline dimensions
Refer to the attached sheets-2-3.
SHARP CORPORATION
6.7
4
Length : L=520 f 2mm
Note 1) Thickness
2) Outer R:
: 0.5k0.2mm
0.5mm
3) Process with applying antistatic
agent.
4) Unless otherwise specified tolerances shall be f0.5mm.
(However except for deformation due to the rubber stopper in sleeve.)
Unit : l/ lmm
Name
Sleeve
outline dimensions
SHMiP
CORPORRTION
Sleeve
\
Anode mark or
arranged at stopper side
Wthout pulled potion.
/Stopper
mwlout
pulled portlon)
(With pulled portion)
-a-
m
I I
I I
20 sleev& (5lines X4sta.M *MAX.
It is impossible to mix
diffierent model or different
rank model in one case.
Kraft tape
Label
Unit:
Name
l/lmm
Packing case
outline dimensions