TI SN74ACT3632

SN74ACT3632
512 × 36 × 2
CLOCKED BIDIRECTIONAL FIRST-IN, FIRST-OUT MEMORY
SCAS224D – JUNE 1992 – REVISED APRIL 1998
D
D
D
D
D
D
Free-Running CLKA and CLKB Can Be
Asynchronous or Coincident
Two Independent 512 × 36 Clocked FIFOs
Buffering Data in Opposite Directions
Mailbox-Bypass Register for Each FIFO
Programmable Almost-Full and
Almost-Empty Flags
Microprocessor Interface Control Logic
IRA, ORA, AEA, and AFA Flags
Synchronized by CLKA
D
D
D
D
D
D
IRB, ORB, AEB, and AFB Flags
Synchronized by CLKB
Low-Power 0.8-µm Advanced CMOS
Technology
Supports Clock Frequencies up to 67 MHz
Fast Access Times of 11 ns
Pin-to-Pin Compatible With the
SN74ACT3622 and SN74ACT3642
Package Options Include 120-Pin Thin
Quad Flat (PCB) and 132-Pin Plastic Quad
Flat (PQ) Packages
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
B35
B34
B33
B32
GND
B31
B30
B29
B28
B27
B26
VCC
B25
B24
GND
B23
B22
B21
B20
B19
B18
GND
B17
B16
VCC
B15
B14
B13
B12
GND
B7
B8
B9
B10
B11
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
GND
A11
A10
A9
A8
A7
A6
GND
A5
A4
A3
VCC
A2
A1
A0
GND
B0
B1
B2
B3
B4
B5
GND
B6
VCC
A35
A34
A33
A32
VCC
A31
A30
GND
A29
A28
A27
A26
A25
A24
A23
GND
A22
VCC
A21
A20
A19
A18
GND
A17
A16
A15
A14
A13
VCC
A12
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
GND
CLKA
ENA
W/RA
CSA
IRA
ORA
VCC
AFA
AEA
MBF2
MBA
RST1
FS0
GND
FS1
RST2
MBB
MBF1
VCC
AEB
AFB
ORB
IRB
GND
CSB
W/RB
ENB
CLKB
VCC
PCB PACKAGE
(TOP VIEW)
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  1998, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SN74ACT3632
512 × 36 × 2
CLOCKED BIDIRECTIONAL FIRST-IN, FIRST-OUT MEMORY
SCAS224D – JUNE 1992 – REVISED APRIL 1998
NC
NC
VCC
CLKB
ENB
W/RB
CSB
GND
IRB
ORB
AFB
AEB
VCC
MBF1
MBB
RST2
FS1
GND
FS0
RST1
MBA
MBF2
AEA
AFA
VCC
ORA
IRA
CSA
W/RA
ENA
CLKA
GND
NC
PQ PACKAGE†
(TOP VIEW)
17 16 15 14 13 12 11 10 9
NC
B35
B34
B33
B32
GND
B31
B30
B29
B28
B27
B26
VCC
B25
B24
GND
B23
B22
B21
B20
B19
B18
GND
B17
B16
VCC
B15
B14
B13
B12
GND
NC
NC
8
7
6
5
4
3
2
18
126 124
122 120 118
1 132 130 128
129
121
119
131
127
125 123
117
116
19
115
20
114
21
113
22
112
23
111
24
110
25
109
26
108
27
107
28
106
29
105
30
104
31
103
32
102
33
101
34
100
35
99
36
98
37
97
38
96
39
95
40
94
41
93
42
92
43
91
44
90
45
89
46
88
47
87
48
86
49
85
84
50
NC
B11
B10
B9
B8
B7
VCC
B6
GND
B5
B4
B3
B2
B1
B0
GND
A0
A1
A2
VCC
A3
A4
A5
GND
A6
A7
A8
A9
A10
A11
GND
NC
NC
51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83
NC – No internal connection
† Uses Yamaichi socket IC51-1324-828
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
NC
NC
A35
A34
A33
A32
VCC
A31
A30
GND
A29
A28
A27
A26
A25
A24
A23
GND
A22
VCC
A21
A20
A19
A18
GND
A17
A16
A15
A14
A13
VCC
A12
NC
SN74ACT3632
512 × 36 × 2
CLOCKED BIDIRECTIONAL FIRST-IN, FIRST-OUT MEMORY
SCAS224D – JUNE 1992 – REVISED APRIL 1998
description
The SN74ACT3632 is a high-speed, low-power CMOS clocked bidirectional FIFO memory. It supports clock
frequencies up to 67 MHz and has read access times as fast as 11 ns. Two independent 512 × 36 dual-port
SRAM FIFOs on the chip buffer data in opposite directions. Each FIFO has flags to indicate empty and full
conditions and two programmable flags, almost full (AF) and almost empty (AE) to indicate when a selected
number of words is stored in memory. Communication between each port can bypass the FIFOs via two 36-bit
mailbox registers. Each mailbox register has a flag to signal when new mail has been stored. Two or more
devices can be used in parallel to create wider datapaths.
The SN74ACT3632 is a clocked FIFO, which means each port employs a synchronous interface. All data
transfers through a port are gated to the low-to-high transition of a port clock by enable signals. The clocks for
each port are independent of one another and can be asynchronous or coincident. The enables for each port
are arranged to provide a simple bidirectional interface between microprocessors and/or buses with
synchronous control.
The input-ready (IRA, IRB) flag and almost-full (AFA, AFB) flag of a FIFO are two-stage synchronized to the
port clock that writes data to its array. The output-ready (ORA, ORB) flag and almost-empty (AEA, AEB) flag
of a FIFO are two-stage synchronized to the port clock that reads data from its array. Offset values for the AF
and AE flags of both FIFOs can be programmed from port A.
The SN74ACT3632 is characterized for operation from 0°C to 70°C.
For more information on this device family, see the following application reports:
•
•
•
FIFO Mailbox-Bypass Registers: Using Bypass Registers to Initialize DMA Control
(literature number SCAA007)
Interfacing TI Clocked FIFOs With TI Floating-Point Digital Signal Processors (literature number
SCAA005)
Metastability Performance of Clocked FIFOs (literature number SCZA004)
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SN74ACT3632
512 × 36 × 2
CLOCKED BIDIRECTIONAL FIRST-IN, FIRST-OUT MEMORY
SCAS224D – JUNE 1992 – REVISED APRIL 1998
functional block diagram
MBF1
RST1
FIFO1,
Mail1
Reset
Logic
512 × 36
SRAM
Write
Pointer
Output Register
Port-A
Control
Logic
Input Register
Mail1
Register
CLKA
CSA
W/RA
ENA
MBA
36
Read
Pointer
Status-Flag
Logic
IRA
AFA
ORB
AEB
FIFO1
36
FS0
FS1
A0 – A35
ProgrammableFlag
Offset Registers
9
B0 – B35
FIFO2
Status-Flag
Logic
Output Register
Read
Pointer
IRB
AFB
36
Write
Pointer
512 × 36
SRAM
Input Register
ORA
AEA
Mail2
Register
MBF2
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
FIFO2,
Mail2
Reset
Logic
RST2
Port-B
Control
Logic
CLKB
CSB
W/RB
ENB
MBB
SN74ACT3632
512 × 36 × 2
CLOCKED BIDIRECTIONAL FIRST-IN, FIRST-OUT MEMORY
SCAS224D – JUNE 1992 – REVISED APRIL 1998
Terminal Functions
TERMINAL
NAME
I/O
A0 – A35
I/O
AEA
O
(port A)
Port-A almost-empty flag. Programmable flag synchronized to CLKA. AEA is low when the number of words in FIFO2
is less than or equal to the value in the almost-empty A offset register, X2.
AEB
O
(port B)
Port-B almost-empty flag. Programmable flag synchronized to CLKB. AEB is low when the number of words in FIFO1
is less than or equal to the value in the almost-empty B offset register, X1.
AFA
O
(port A)
Port-A almost-full flag. Programmable flag synchronized to CLKA. AFA is low when the number of empty locations in
FIFO1 is less than or equal to the value in the almost-full A offset register, Y1.
AFB
O
(port B)
Port-B almost-full flag. Programmable flag synchronized to CLKB. AFB is low when the number of empty locations in
FIFO2 is less than or equal to the value in the almost-full B offset register, Y2.
B0 – B35
I/O
CLKA
I
Port-A clock. CLKA is a continuous clock that synchronizes all data transfers through port A and can be asynchronous
or coincident to CLKB. IRA, ORA, AFA, and AEA are all synchronized to the low-to-high transition of CLKA.
CLKB
I
Port-B clock. CLKB is a continuous clock that synchronizes all data transfers through port B and can be asynchronous
or coincident to CLKA. IRB, ORB, AFB, and AEB are synchronized to the low-to-high transition of CLKB.
CSA
I
Port-A chip select. CSA must be low to enable a low-to-high transition of CLKA to read or write data on port A. The
A0 – A35 outputs are in the high-impedance state when CSA is high.
CSB
I
Port-B chip select. CSB must be low to enable a low-to-high transition of CLKB to read or write data on port B. The
B0 – B35 outputs are in the high-impedance state when CSB is high.
ENA
I
Port-A enable. ENA must be high to enable a low-to-high transition of CLKA to read or write data on port A.
ENB
I
Port-B enable. ENB must be high to enable a low-to-high transition of CLKB to read or write data on port B.
FS1, FS0
I
Flag-offset selects. The low-to-high transition of a FIFO reset input latches the values of FS0 and FS1. If either FS0
or FS1 is high when a reset input goes high, one of three preset values is selected as the offset for the FIFO AF and
AE flags. If both FIFOs are reset simultaneously and both FS0 and FS1 are low when RST1 and RST2 go high, the
first four writes to FIFO1 program the almost-full and almost-empty offsets for both FIFOs.
IRA
O
(port A)
Input-ready flag. IRA is synchronized to the low-to-high transition of CLKA. When IRA is low, FIFO1 is full and writes
to its array are disabled. IRA is set low when FIFO1 is reset and is set high on the second low-to-high transition of CLKA
after reset.
IRB
O
(port B)
Input-ready flag. IRB is synchronized to the low-to-high transition of CLKB. When IRB is low, FIFO2 is full and writes
to its array are disabled. IRB is set low when FIFO2 is reset and is set high on the second low-to-high transition of CLKB
after reset.
MBA
I
Port-A mailbox select. A high level on MBA chooses a mailbox register for a port-A read or write operation. When the
A0 – A35 outputs are active, a high level on MBA selects data from the mail2 register for output and a low level selects
FIFO2 output-register data for output.
MBB
I
Port-B mailbox select. A high level on MBB chooses a mailbox register for a port-B read or write operation. When the
B0 – B35 outputs are active, a high level on MBB selects data from the mail1 register for output and a low level selects
FIFO1 output-register data for output.
MBF1
O
Mail1 register flag. MBF1 is set low by the low-to-high transition of CLKA that writes data to the mail1 register. Writes
to the mail1 register are inhibited while MBF1 is low. MBF1 is set high by a low-to-high transition of CLKB when a port-B
read is selected and MBB is high. MBF1 is set high when FIFO1 is reset.
MBF2
O
Mail2 register flag. MBF2 is set low by the low-to-high transition of CLKB that writes data to the mail2 register. Writes
to the mail2 register are inhibited while MBF2 is low. MBF2 is set high by a low-to-high transition of CLKA when a port-A
read is selected and MBA is high. MBF2 is also set high when FIFO2 is reset.
ORA
O
(port A)
Output-ready flag. ORA is synchronized to the low-to-high transition of CLKA. When ORA is low, FIFO2 is empty and
reads from its memory are disabled. Ready data is present on the output register of FIFO2 when ORA is high. ORA
is forced low when FIFO2 is reset and goes high on the third low-to-high transition of CLKA after a word is loaded to
empty memory.
DESCRIPTION
Port-A data. The 36-bit bidirectional data port for side A.
Port-B data. The 36-bit bidirectional data port for side B.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
SN74ACT3632
512 × 36 × 2
CLOCKED BIDIRECTIONAL FIRST-IN, FIRST-OUT MEMORY
SCAS224D – JUNE 1992 – REVISED APRIL 1998
Terminal Functions (Continued)
TERMINAL
NAME
I/O
DESCRIPTION
ORB
O
(port B)
Output-ready flag. ORB is synchronized to the low-to-high transition of CLKB. When ORB is low, FIFO1 is empty and
reads from its memory are disabled. Ready data is present on the output register of FIFO1 when ORB is high. ORB
is forced low when FIFO1 is reset and goes high on the third low-to-high transition of CLKB after a word is loaded to
empty memory.
RST1
I
FIFO1 reset. To reset FIFO1, four low-to-high transitions of CLKA and four low-to-high transitions of CLKB must occur
while RST1 is low. The low-to-high transition of RST1 latches the status of FS0 and FS1 for AFA and AEB offset
selection. FIFO1 must be reset upon power up before data is written to its RAM.
RST2
I
FIFO2 reset. To reset FIFO2, four low-to-high transitions of CLKA and four low-to-high transitions of CLKB must occur
while RST2 is low. The low-to-high transition of RST2 latches the status of FS0 and FS1 for AFB and AEA offset
selection. FIFO2 must be reset upon power up before data is written to its RAM.
W/RA
I
Port-A write/read select. A high on W/RA selects a write operation and a low selects a read operation on port A for a
low-to-high transition of CLKA. The A0 – A35 outputs are in the high-impedance state when W/RA is high.
W/RB
I
Port-B write/read select. A low on W/RB selects a write operation and a high selects a read operation on port B for a
low-to-high transition of CLKB. The B0 – B35 outputs are in the high-impedance state when W/RB is low.
detailed description
reset
The FIFO memories of the SN74ACT3632 are reset separately by taking their reset (RST1, RST2) inputs low
for at least four port-A clock (CLKA) and four port-B clock (CLKB) low-to-high transitions. The reset inputs can
switch asynchronously to the clocks. A FIFO reset initializes the internal read and write pointers and forces the
input-ready flag (IRA, IRB) low, the output-ready flag (ORA, ORB) low, the almost-empty flag (AEA, AEB) low,
and the almost-full flag (AFA, AFB) high. Resetting a FIFO also forces the mailbox flag (MBF1, MBF2) of the
parallel mailbox register high. After a FIFO is reset, its input-ready flag is set high after two clock cycles to begin
normal operation. A FIFO must be reset after power up before data is written to its memory.
A low-to-high transition on a FIFO reset (RST1, RST2) input latches the value of the flag-select (FS0, FS1)
inputs for choosing the almost-full and almost-empty offset programming method.
almost-empty flag and almost-full flag offset programming
Four registers in the SN74ACT3632 are used to hold the offset values for the AE and AF flags. The port-B
almost-empty flag (AEB) offset register is labeled X1 and the port-A almost-empty flag (AEA) offset register is
labeled X2. The port-A almost-full flag (AFA) offset register is labeled Y1 and the port-B almost-full flag (AFB)
offset register is labeled Y2. The index of each register name corresponds to its FIFO number. The offset
registers can be loaded with preset values during the reset of a FIFO or they can be programmed from port A
(see Table 1).
Table 1. Flag Programming
RST1
RST2
X1 AND Y1 REGISTERS†
H
↑
X
64
X
H
X
↑
X
64
L
↑
X
16
X
L
X
↑
X
16
H
↑
X
8
X
H
X
↑
X
8
L
↑
↑
Programmed from port A
Programmed from port A
FS1
FS0
H
H
H
H
L
L
L
X2 AND Y2 REGISTERS‡
† X1 register holds the offset for AEB; Y1 register holds the offset for AFA.
‡ X2 register holds the offset for AEA; Y2 register holds the offset for AFB.
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN74ACT3632
512 × 36 × 2
CLOCKED BIDIRECTIONAL FIRST-IN, FIRST-OUT MEMORY
SCAS224D – JUNE 1992 – REVISED APRIL 1998
almost-empty flag and almost-full flag offset programming (continued)
To load the AE flag and AF flag offset registers of a FIFO with one of the three preset values listed in Table 1,
at least one of the flag-select inputs must be high during the low-to-high transition of its reset input. For example,
to load the preset value of 64 into X1 and Y1, FS0 and FS1 must be high when FIFO1 reset (RST1) returns high.
Flag-offset registers associated with FIFO2 are loaded with one of the preset values in the same way with FIFO2
reset (RST2). When using one of the preset values for the flag offsets, the FIFOs can be reset simultaneously
or at different times.
To program the X1, X2, Y1, and Y2 registers from port A, both FIFOs should be reset simultaneously with FS0
and FS1 low during the low-to-high transition of the reset inputs. After this reset is complete, the first four writes
to FIFO1 do not store data in RAM but load the offset registers in the order Y1, X1, Y2, X2. Each offset register
uses port-A (A8 – A0) inputs, with A8 as the most-significant bit. Each register value can be programmed from
1 to 508. After all the offset registers are programmed from port A, the port-B input-ready flag (IRB) is set high
and both FIFOs begin normal operation.
FIFO write/read operation
The state of the port-A data (A0 – A35) outputs is controlled by the port-A chip select (CSA) and the port-A
write/read select (W/RA). The A0 – A35 outputs are in the high-impedance state when either CSA or W/RA is
high. The A0 – A35 outputs are active when both CSA and W/RA are low.
Data is loaded into FIFO1 from the A0 – A35 inputs on a low-to-high transition of CLKA when CSA is low, W/RA
is high, ENA is high, MBA is low, and IRA is high. Data is read from FIFO2 to the A0 – A35 outputs by a low-to-high
transition of CLKA when CSA is low, W/RA is low, ENA is high, MBA is low, and ORA is high (see Table 2). FIFO
reads and writes on port A are independent of any concurrent port-B operation.
Table 2. Port-A Enable Function Table
CSA
W/RA
ENA
MBA
CLKA
A0 – A35 OUTPUTS
PORT FUNCTION
H
X
X
X
X
In high-impedance state
None
L
H
L
X
X
In high-impedance state
None
L
H
H
L
↑
In high-impedance state
FIFO1 write
L
H
H
H
↑
In high-impedance state
Mail1 write
L
L
L
L
X
Active, FIFO2 output register
None
L
L
H
L
↑
Active, FIFO2 output register
FIFO2 read
L
L
L
H
X
Active, mail2 register
None
L
L
H
H
↑
Active, mail2 register
Mail2 read (set MBF2 high)
The port-B control signals are identical to those of port A, with the exception that the port-B write/read select
(W/RB) is the inverse of the port-A write/read select (W/RA). The state of the port-B data (B0 – B35) outputs is
controlled by the port-B chip select (CSB) and the port-B write/read select (W/RB). The B0 – B35 outputs are
in the high-impedance state when either CSB is high or W/RB is low. The B0 – B35 outputs are active when CSB
is low and W/RB is high.
Data is loaded into FIFO2 from the B0 – B35 inputs on a low-to-high transition of CLKB when CSB is low, W/RB
is low, ENB is high, MBB is low, and IRB is high. Data is read from FIFO1 to the B0 – B35 outputs by a low-to-high
transition of CLKB when CSB is low, W/RB is high, ENB is high, MBB is low, and ORB is high (see Table 3). FIFO
reads and writes on port B are independent of any concurrent port-A operation.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
SN74ACT3632
512 × 36 × 2
CLOCKED BIDIRECTIONAL FIRST-IN, FIRST-OUT MEMORY
SCAS224D – JUNE 1992 – REVISED APRIL 1998
FIFO write/read operation (continued)
Table 3. Port-B Enable Function Table
CSB
W/RB
ENB
MBB
CLKB
B0 – B35 OUTPUTS
PORT FUNCTION
H
X
X
X
X
In high-impedance state
None
L
L
L
X
X
In high-impedance state
None
L
L
H
L
↑
In high-impedance state
FIFO2 write
L
L
H
H
↑
In high-impedance state
Mail2 write
L
H
L
L
X
Active, FIFO1 output register
None
L
H
H
L
↑
Active, FIFO1 output register
FIFO1 read
L
H
L
H
X
Active, mail1 register
None
L
H
H
H
↑
Active, mail1 register
Mail1 read (set MBF1 high)
The setup- and hold-time constraints to the port clocks for the port-chip selects and write/read selects are only
for enabling write and read operations and are not related to high-impedance control of the data outputs. If a
port enable is low during a clock cycle, the port-chip select and write/read select may change states during the
setup- and hold-time window of the cycle.
When a FIFO OR flag is low, the next data word is sent to the FIFO output register automatically by the
low-to-high transition of the port clock that sets the OR flag high. When the OR flag is high, an available data
word is clocked to the FIFO output register only when a FIFO read is selected by the port’s chip select, write/read
select, enable, and mailbox select.
synchronized FIFO flags
Each FIFO is synchronized to its port clock through at least two flip-flop stages. This is done to improve
flag-signal reliability by reducing the probability of metastable events when CLKA and CLKB operate
asynchronously to one another. ORA, AEA, IRA, and AFA are synchronized to CLKA. ORB, AEB, IRB, and AFB
are synchronized to CLKB. Tables 4 and 5 show the relationship of each port flag to FIFO1 and FIFO2.
Table 4. FIFO1 Flag Operation
NUMBER OF WORDS
IN FIFO1†‡
SYNCHRONIZED
TO CLKB
ORB
AEB
SYNCHRONIZED
TO CLKA
AFA
IRA
0
L
L
H
H
1 to X1
H
L
H
H
(X1 + 1) to [512 – (Y1 + 1)]
H
H
H
H
(512 – Y1) to 511
H
H
L
H
512
H
H
L
L
† X1 is the almost-empty offset for FIFO1 used by AEB. Y1 is the almost-full
offset for FIFO1 used by AFA. Both X1 and Y1 are selected during a reset of
FIFO1 or programmed from port A.
‡ When a word loaded to an empty FIFO is shifted to the output register, its
previous FIFO memory location is free.
8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN74ACT3632
512 × 36 × 2
CLOCKED BIDIRECTIONAL FIRST-IN, FIRST-OUT MEMORY
SCAS224D – JUNE 1992 – REVISED APRIL 1998
synchronized FIFO flags (continued)
Table 5. FIFO2 Flag Operation
NUMBER OF WORDS
IN FIFO2†‡
SYNCHRONIZED
TO CLKA
SYNCHRONIZED
TO CLKB
ORA
AEA
AFB
IRB
0
L
L
H
H
1 to X2
H
L
H
H
(X2 + 1) to [512 – (Y2 + 1)]
H
H
H
H
(512 – Y2) to 511
H
H
L
H
512
H
H
L
L
† X2 is the almost-empty offset for FIFO2 used by AEA. Y2 is the almost-full
offset for FIFO2 used by AFB. Both X2 and Y2 are selected during a reset
of FIFO2 or programmed from port A.
‡ When a word loaded to an empty FIFO is shifted to the output register, its
previous FIFO memory location is free.
output-ready flags (ORA, ORB)
The OR flag of a FIFO is synchronized to the port clock that reads data from its array. When the OR flag is high,
new data is present in the FIFO output register. When the OR flag is low, the previous data word is present in
the FIFO output register and attempted FIFO reads are ignored.
A FIFO read pointer is incremented each time a new word is clocked to its output register. From the time a word
is written to a FIFO, it can be shifted to the FIFO output register in a minimum of three cycles of the OR flag
synchronizing clock; therefore, an OR flag is low if a word in memory is the next data to be sent to the FIFO output
register and three cycles of the port clock that reads data from the FIFO have not elapsed since the time the
word was written. The OR flag of the FIFO remains low until the third low-to-high transition of the synchronizing
clock occurs, simultaneously forcing the OR flag high and shifting the word to the FIFO output register.
A low-to-high transition on an OR flag synchronizing clock begins the first synchronization cycle of a write if the
clock transition occurs at time tsk1, or greater, after the write. Otherwise, the subsequent clock cycle can be the
first synchronization cycle (see Figures 7 and 8).
input-ready flags (IRA, IRB)
The IR flag of a FIFO is synchronized to the port clock that writes data to its array. When the IR flag is high, a
memory location is free in the SRAM to receive new data. No memory locations are free when the IR flag is low
and attempted writes to the FIFO are ignored.
Each time a word is written to a FIFO, its write pointer is incremented. From the time a word is read from a FIFO,
its previous memory location is ready to be written in a minimum of two cycles of the IR flag synchronizing clock;
therefore, an IR flag is low if less than two cycles of the IR flag synchronizing clock have elapsed since the next
memory write location has been read. The second low-to-high transition on the IR flag synchronizing clock after
the read sets the IR flag high.
A low-to-high transition on an IR flag synchronizing clock begins the first synchronization cycle of a read if the
clock transition occurs at time tsk1, or greater, after the read. Otherwise, the subsequent clock cycle can be the
first synchronization cycle (see Figures 9 and 10).
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
SN74ACT3632
512 × 36 × 2
CLOCKED BIDIRECTIONAL FIRST-IN, FIRST-OUT MEMORY
SCAS224D – JUNE 1992 – REVISED APRIL 1998
almost-empty flags (AEA, AEB)
The AE flag of a FIFO is synchronized to the port clock that reads data from its array. The almost-empty state
is defined by the contents of register X1 for AEB and register X2 for AEA. These registers are loaded with preset
values during a FIFO reset or programmed from port A (see almost-empty flag and almost-full flag offset
programming). An AE flag is low when its FIFO contains X or fewer words and is high when its FIFO contains
(X + 1) or more words. A data word present in the FIFO output register has been read from memory.
Two low-to-high transitions of the AE flag synchronizing clock are required after a FIFO write for its AE flag to
reflect the new level of fill. Therefore, the AE flag of a FIFO containing (X + 1) or more words remains low if two
cycles of its synchronizing clock have not elapsed since the write that filled the memory to the (X + 1) level. An
AE flag is set high by the second low-to-high transition of its synchronizing clock after the FIFO write that fills
memory to the (X + 1) level. A low-to-high transition of an AE flag synchronizing clock begins the first
synchronization cycle if it occurs at time tsk2, or greater, after the write that fills the FIFO to (X + 1) words.
Otherwise, the subsequent synchronizing clock cycle can be the first synchronization cycle
(see Figures 11 and 12).
almost-full flags (AFA, AFB)
The AF flag of a FIFO is synchronized to the port clock that writes data to its array. The almost-full state is defined
by the contents of register Y1 for AFA and register Y2 for AFB. These registers are loaded with preset values
during a FIFO reset or programmed from port A (see almost-empty flag and almost-full flag offset programming).
An AF flag is low when its FIFO contains (512 – Y) or more words and is high when its FIFO contains
[512 – (Y + 1)] or fewer words. A data word is present in the FIFO output register has been read from memory.
Two low-to-high transitions of the AF flag synchronizing clock are required after a FIFO read for its AF flag to
reflect the new level of fill. Therefore, the AF flag of a FIFO containing [512 – (Y + 1)] or fewer words remains
low if two cycles of its synchronizing clock have not elapsed since the read that reduced the number of words
in memory to [512 – (Y + 1)]. An AF flag is set high by the second low-to-high transition of its synchronizing clock
after the FIFO read that reduces the number of words in memory to [512 – (Y + 1)]. A low-to-high transition of
an AF flag synchronizing clock begins the first synchronization cycle if it occurs at time tsk2, or greater, after the
read that reduces the number of words in memory to [512 – (Y + 1)]. Otherwise, the subsequent synchronizing
clock cycle can be the first synchronization cycle (see Figures 13 and 14).
mailbox registers
Each FIFO has a 36-bit bypass register to pass command and control information between port A and port B
without putting it in queue. The mailbox-select (MBA, MBB) inputs choose between a mail register and a FIFO
for a port-data-transfer operation. A low-to-high transition on CLKA writes A0 – A35 data to the mail1 register
when a port-A write is selected by CSA, W/RA, and ENA and with MBA high. A low-to-high transition on CLKB
writes B0 – B35 data to the mail2 register when a port-B write is selected by CSB, W/RB, and ENB and with MBB
high. Writing data to a mail register sets its corresponding flag (MBF1 or MBF2) low. Attempted writes to a mail
register are ignored while the mail flag is low.
When data outputs of a port are active, the data on the bus comes from the FIFO output register when the port
mailbox select input is low and from the mail register when the port-mailbox select input is high. The mail1
register flag (MBF1) is set high by a low-to-high transition on CLKB when a port-B read is selected by CSB,
W/RB, and ENB and with MBB high. The mail2 register flag (MBF2) is set high by a low-to-high transition on
CLKA when a port-A read is selected by CSA, W/RA, and ENA and with MBA high. The data in a mail register
remains intact after it is read and changes only when new data is written to the register.
10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN74ACT3632
512 × 36 × 2
CLOCKED BIDIRECTIONAL FIRST-IN, FIRST-OUT MEMORY
SCAS224D – JUNE 1992 – REVISED APRIL 1998
CLKA
th(RS)
CLKB
th(FS)
tsu(RS)
tsu(FS)
ÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏ ÏÏÏÏÏÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏÏÏÏÏÏ
ÌÌÌÌÌÌÌÌÌÌÌÌ
ÌÌÌÌÌÌÌÌÌÌÌÌ
ÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌ
ÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌ
ÌÌÌÌÌÌÌÌ
ÌÌÌÌÌÌÌÌ
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
RST1
FS1, FS0
0,1
tpd(C-IR)
tpd(C-IR)
IRA
tpd(C-OR)
ORB
tpd(R-F)
AEB
tpd(R-F)
AFA
tpd(R-F)
MBF1
Figure 1. FIFO1 Reset Loading X1 and Y1 With a Preset Value of Eight†
† FIFO2 is reset in the same manner to load X2 and Y2 with a preset value.
CLKA
RST1,
RST2
4
tsu(FS)
Ï ÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏ
ÎÎÎÎÎÎÎÎÎÎÎ
ÏÏÏÏÏÏÏÏÏÏÏÏÏÏ
ÌÌÌÌÌÌ
ÎÎÎÎÎÎÎÎÎÎÎ
ÏÏÏÏ
ÏÏÏ
ÏÏÏ
ÏÏÏÏ
ÌÌÌÌÌÌ
ÏÏÏÏÏÏÏÏÏÏ ÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏ
th(FS)
FS1, FS0
0,0
tpd(C-IR)
IRA
ENA
tsu(EN)
tsu(D)
A0 – A35
AFA Offset
(Y1)
tsk1‡
th(EN)
th(D)
AEB Offset
(X1)
AFB Offset
(Y2)
CLKB
AEA Offset
(X2)
First Word to FIFO1
1
2
tpd(C-IR)
IRB
‡ tsk1 is the minimum time between the rising CLKA edge and a rising CLKB edge for IRB to transition high in the next cycle. If the time
between the rising edge of CLKA and rising edge of CLKB is less than tsk1, IRB may transition high one cycle later than shown.
NOTE A: CSA = L, W/RA = H, MBA = L. It is not necessary to program offset register on consecutive clock cycles.
Figure 2. Programming the AF Flag and AE Flag Offset Values After Reset
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
SN74ACT3632
512 × 36 × 2
CLOCKED BIDIRECTIONAL FIRST-IN, FIRST-OUT MEMORY
SCAS224D – JUNE 1992 – REVISED APRIL 1998
tc
tw(CLKH)
tw(CLKL)
CLKA
IRA
CSA
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÌÌÌÌÌÌÌÌ
ÌÌÌÌÌÌÌÌ
ÎÎÎÎÎÎÎÎ
ÏÏÏÏÏÏÏ
tsu(EN)
W/RA
tsu(EN)
MBA
tsu(EN)
ENA
tsu(D)
W1†
A0 – A35
ÏÏÏ
ÏÏÏ
ÏÏÏ
ÌÌÌÌÌÌ
ÏÏÏ
ÌÌÌÌÌÌ
ÏÏÏ
ÎÎÎÎÎÎ
ÏÏÏ
ÎÎÎÎÎÎ
ÏÏÏÏÏÏ ÌÌÌÌÌÌÌ ÎÎÎÎÎÎ
ÏÏÏÏÏÏ ÏÏÏÏÏÏÏÏÏÏÏÏÏÏ
th(EN)
tsu(EN)
† Written to FIFO1
th(EN)
th(EN)
th(EN)
th(EN)
tsu(EN)
th(EN)
tsu(EN)
th(D)
W2†
No Operation
Figure 3. Port-A Write-Cycle Timing for FIFO1
tc
tw(CLKH)
tw(CLKL)
CLKB
IRB
CSB
ÌÌÌÌÌÌÌÌ
ÌÌÌÌÌÌÌÌ
ÌÌÌÌÌÌÌÌ
ÌÌÌÌÌÌÌÌ
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏ
tsu(EN)
W/RB
tsu(EN)
MBB
tsu(EN)
ENB
tsu(D)
B0 – B35
‡ Written to FIFO2
ÏÏÏ
ÏÏÏ
ÏÏÏ
ÏÏÏ
ÏÏÏ
ÏÏÏ
ÏÏÏÏÏÏ
ÏÏÏÏÏÏ
ÏÏÏÏÏÏ
ÏÏÏÏÏÏ
th(EN)
tsu(EN)
W1†
th(EN)
th(EN)
th(EN)
tsu(EN)
th(D)
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÌÌÌÌÌÌÌ ÎÎÎÎÎÎ
ÌÌÌÌÌÌÌ
ÎÎÎÎÎÎ
ÏÏÏÏÏÏÏÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏÏÏÏÏÏÏÏ
th(EN)
W2‡
Figure 4. Port-B Write-Cycle Timing for FIFO2
12
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
th(EN)
tsu(EN)
No Operation
SN74ACT3632
512 × 36 × 2
CLOCKED BIDIRECTIONAL FIRST-IN, FIRST-OUT MEMORY
SCAS224D – JUNE 1992 – REVISED APRIL 1998
tc
tw(CLKH)
tw(CLKL)
CLKA
ORA
ÌÌÌÌ
ÌÌÌÌ
ÎÎÎÎÎÎÎÎ ÏÏÏÏÏÏÏ ÌÌÌÌÌÌ
ÎÎÎÎÎÎÎÎ ÏÏÏÏÏÏÏ ÌÌÌÌÌÌ
ÏÏÏ
ÏÏÏ
CSA
W/RA
tsu(EN)
MBA
th(EN) tsu(EN)
th(EN)
tsu(EN)
ENA
ta
ta
W1†
A0 – A35
th(EN)
No
Operation
tpd(M-DV)
ten
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
W2†
tdis
W3†
† Read from FIFO2
Figure 5. Port-A Read-Cycle Timing for FIFO2
tc
tw(CLKH)
tw(CLKL)
CLKB
ORB
CSB
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎ ÏÏÏÏÏÏÏ ÌÌÌÌÌÌ
ÎÎÎÎÎÎÎÎ ÏÏÏÏÏÏÏ ÌÌÌÌÌÌ
ÏÏÏ
ÏÏÏ
W/RB
tsu(EN)
MBB
th(EN) tsu(EN)
th(EN)
tsu(EN)
ENB
tpd(M-DV)
B0 – B35
ta
ta
ten
W1‡
W2‡
ÌÌÌÌÌÌ
ÌÌÌÌÌÌ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
No
Operation
th(EN)
tdis
W3‡
‡ Read from FIFO1
Figure 6. Port-B Read-Cycle Timing for FIFO1
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
SN74ACT3632
512 × 36 × 2
CLOCKED BIDIRECTIONAL FIRST-IN, FIRST-OUT MEMORY
SCAS224D – JUNE 1992 – REVISED APRIL 1998
tc
tw(CLKH)
tw(CLKL)
CLKA
CSA
W/RA
Low
High
tsu(EN)
ÌÌÌÌÌ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÌÌÌÌ
ÎÎÎÎÌÌÌÌ
ÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏ
th(EN)
MBA
tsu(EN)
th(EN)
ENA
IRA
High
tsu(D)
A0 – A35
th(D)
W1
tc
tw(CLKL)
tsk1†
tw(CLKH)
1
CLKB
2
3
tpd(C-OR)
tpd(C-OR)
Old Data in FIFO1 Output Register
ORB
CSB
Low
W/RB
High
MBB
Low
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÌÌÌÌÌÌÌÌÌ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÌÌÌÌÌÌÌÌÌ
tsu(EN)
th(EN)
ENB
ta
B0 – B35
Old Data in FIFO1 Output Register
W1
† tsk1 is the minimum time between a rising CLKA edge and a rising CLKB edge for ORB to transition high and to clock the next word to the
FIFO1 output register in three CLKB cycles. If the time between the rising CLKA edge and rising CLKB edge is less than tsk1, the transition
of ORB high and load of the first word to the output register may occur one CLKB cycle later than shown.
Figure 7. ORB-Flag Timing and First Data-Word Fall-Through When FIFO1 Is Empty
14
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN74ACT3632
512 × 36 × 2
CLOCKED BIDIRECTIONAL FIRST-IN, FIRST-OUT MEMORY
SCAS224D – JUNE 1992 – REVISED APRIL 1998
tc
tw(CLKH)
tw(CLKL)
CLKB
CSB
Low
W/RB
Low
tsu(EN)
ÌÌÌÌÌ
ÎÎÎÎ
ÎÎÎÎ
ÏÏÏÏÏ
tsu(EN)
th(EN)
ENB
IRB
High tsu(D)
B0 – B35
th(D)
W1
tsk1†
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÌÌÌÌ
ÌÌÌÌ
ÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏ
th(EN)
MBB
tc
tw(CLKL)
tw(CLKH)
1
CLKA
2
3
tpd(C-OR)
tpd(C-OR)
Old Data in FIFO2 Output Register
ORA
CSA
Low
W/RA
Low
MBA
Low
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÌÌÌÌÌÌÌÌ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÌÌÌÌÌÌÌÌ
tsu(EN)
th(EN)
ENA
ta
A0 – A35
W1
Old Data in FIFO2 Output Register
† tsk1 is the minimum time between a rising CLKB edge and a rising CLKA edge for ORA to transition high and to clock the next word to the
FIFO2 output register in three CLKA cycles. If the time between the rising CLKB edge and rising CLKA edge is less than tsk1, the transition
of ORA high and load of the first word to the output register may occur one CLKA cycle later than shown.
Figure 8. ORA-Flag Timing and First Data-Word Fall-Through When FIFO2 Is Empty
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
15
SN74ACT3632
512 × 36 × 2
CLOCKED BIDIRECTIONAL FIRST-IN, FIRST-OUT MEMORY
SCAS224D – JUNE 1992 – REVISED APRIL 1998
tc
tw(CLKH)
tw(CLKL)
CLKB
CSB
Low
W/RB
High
MBB
Low
ÎÎÎÎ ÌÌÌ
ÎÎÎÎ ÌÌÌ
tsu(EN)
ENB
ORB
th(EN)
High
ta
B0 – B35 Previous Word in FIFO1 Output Register
Next Word From FIFO1
tsk1†
tc
tw(CLKH)
1
CLKA
FIFO1 Full
IRA
CSA
tw(CLKL)
2
tpd(C-IR)
tpd(C-IR)
Low
ÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌ
ÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏ
W/RA
High
tsu(EN)
MBA
tsu(EN)
ENA
tsu(D)
A0 – A35
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÌÌÌÌÌÌÌÌ
ÌÌÌÌÌÌÌÌ
ÏÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏÏ
th(EN)
th(EN)
th(D)
To FIFO1
† tsk1 is the minimum time between a rising CLKB edge and a rising CLKA edge for IRA to transition high in the next CLKA cycle. If the time
between the rising CLKB edge and rising CLKA edge is less than tsk1, IRA may transition high one CLKA cycle later than shown.
Figure 9. IRA-Flag Timing and First Available Write When FIFO1 Is Full
16
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN74ACT3632
512 × 36 × 2
CLOCKED BIDIRECTIONAL FIRST-IN, FIRST-OUT MEMORY
SCAS224D – JUNE 1992 – REVISED APRIL 1998
tc
tw(CLKH)
tw(CLKL)
CLKA
CSA
Low
W/RA
Low
MBA
Low
ÎÎÎ ÌÌÌÌ
ÎÎÎ ÌÌÌÌ
tsu(EN)
ENA
ORA
High
th(EN)
ta
A0 – A35 Previous Word in FIFO2 Output Register
Next Word From FIFO2
tsk1†
tc
tw(CLKH)
1
CLKB
FIFO2 Full
IRB
CSB
tw(CLKL)
2
tpd(C-IR)
tpd(C-IR)
Low
ÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌ
ÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏ
W/RB
Low
tsu(EN)
MBB
tsu(EN)
ENB
tsu(D)
B0 – B35
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÌÌÌÌÌÌÌÌÌ
ÌÌÌÌÌÌÌÌÌ
ÏÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏÏ
th(EN)
th(EN)
th(D)
To FIFO2
† tsk1 is the minimum time between a rising CLKA edge and a rising CLKB edge for IRB to transition high in the next CLKB cycle. If the time
between the rising CLKA edge and rising CLKB edge is less than tsk1, IRB may transition high one CLKB cycle later than shown.
Figure 10. IRB-Flag Timing and First Available Write When FIFO2 Is Full
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
17
SN74ACT3632
512 × 36 × 2
CLOCKED BIDIRECTIONAL FIRST-IN, FIRST-OUT MEMORY
SCAS224D – JUNE 1992 – REVISED APRIL 1998
CLKA
ÎÎÎÎÎÌÌÌÌÌ
ÎÎÎÎÎÌÌÌÌÌ
tsu(EN)
ENA
th(EN)
tsk2†
CLKB
AEB
1
2
tpd(C-AE)
X1 Words in FIFO1
tpd(C-AE)
ÎÎÎÎÎÌÌÌÌÌ
ÎÎÎÎÎÌÌÌÌÌ
(X1 + 1) Words in FIFO1
tsu(EN)
ENB
th(EN)
† tsk2 is the minimum time between a rising CLKA edge and a rising CLKB edge for AEB to transition high in the next CLKB cycle. If the time
between the rising CLKA edge and rising CLKB edge is less than tsk2, AEB may transition high one CLKB cycle later than shown.
NOTE A: FIFO1 write (CSA = L, W/RA = H, MBA = L), FIFO1 read (CSB = L, W/RB = H, MBB = L). Data in the FIFO1 output register has been
read from the FIFO.
Figure 11. Timing for AEB When FIFO1 Is Almost Empty
CLKB
ÎÎÎÎÎÌÌÌÌÌ
ÎÎÎÎÎÌÌÌÌÌ
tsu(EN)
ENB
th(EN)
tsk2‡
CLKA
1
2
tpd(C-AE)
AEA
X2 Words in FIFO2
tpd(C-AE)
(X2 + 1) Words in FIFO2
ÎÎÎÎÎÌÌÌÌÌ
ÎÎÎÎÎÌÌÌÌÌ
tsu(EN)
ENA
th(EN)
‡ tsk2 is the minimum time between a rising CLKB edge and a rising CLKA edge for AEA to transition high in the next CLKA cycle. If the time
between the rising CLKB edge and rising CLKA edge is less than tsk2, AEA may transition high one CLKA cycle later than shown.
NOTE A: FIFO2 write (CSB = L, W/RB = L, MBB = L), FIFO2 read (CSA = L, W/RA = L, MBA = L). Data in the FIFO2 output register has been
read from the FIFO.
Figure 12. Timing for AEA When FIFO2 Is Almost Empty
18
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN74ACT3632
512 × 36 × 2
CLOCKED BIDIRECTIONAL FIRST-IN, FIRST-OUT MEMORY
SCAS224D – JUNE 1992 – REVISED APRIL 1998
tsk2†
CLKA
ÎÎÎÎÎ ÌÌÌÌ
ÎÎÎÎÎ ÌÌÌÌ
tsu(EN)
ENA
1
tpd(C-AF)
AFA
2
th(EN)
[512 – (Y1 + 1)] Words in FIFO1
tpd(C-AF)
(512 – Y1) Words in FIFO1
ÎÎÎÎÎÌÌÌÌÌ
ÎÎÎÎÎÌÌÌÌÌ
CLKB
th(EN)
tsu(EN)
ENB
† tsk2 is the minimum time between a rising CLKA edge and a rising CLKB edge for AFA to transition high in the next CLKA cycle. If the time
between the rising CLKA edge and rising CLKB edge is less than tsk2, AFA may transition high one CLKB cycle later than shown.
NOTE A: FIFO1 write (CSA = L, W/RA = H, MBA = L), FIFO1 read (CSB = L, W/RB = H, MBB = L). Data in the FIFO1 output register has been
read from the FIFO.
Figure 13. Timing for AFA When FIFO1 Is Almost Full
tsk2‡
CLKB
ÎÎÎÎÎ ÌÌÌÌ
ÎÎÎÎÎ ÌÌÌÌ
tsu(EN)
ENB
1
tpd(C-AF)
AFB
CLKA
[512 – (Y2 + 1)] Words in FIFO2
tpd(C-AF)
(512 – Y2) Words in FIFO2
ÎÎÎÎÎÌÌÌÌÌ
ÎÎÎÎÎÌÌÌÌÌ
tsu(EN)
ENA
2
th(EN)
th(EN)
‡ tsk2 is the minimum time between a rising CLKB edge and a rising CLKA edge for AFB to transition high in the next CLKB cycle. If the time
between the rising CLKB edge and rising CLKA edge is less than tsk2, AFB may transition high one CLKA cycle later than shown.
NOTE A: FIFO2 write (CSB = L, W/RB= L, MBB = L), FIFO2 read (CSA = L, W/RA = L, MBA = L). Data in the FIFO2 output register has been
read from the FIFO.
Figure 14. Timing for AFB When FIFO2 Is Almost Full
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
19
SN74ACT3632
512 × 36 × 2
CLOCKED BIDIRECTIONAL FIRST-IN, FIRST-OUT MEMORY
SCAS224D – JUNE 1992 – REVISED APRIL 1998
CLKA
th(EN)
tsu(EN)
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏ
CSA
W/RA
MBA
ENA
tsu(D)
A0 – A35
W1
ÏÏÏ
ÏÏÏ
ÏÏÏ
ÏÏÏ
ÏÏÏ
ÏÏÏ
ÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏ
th(D)
CLKB
tpd(C-MF)
tpd(C-MF)
MBF1
CSB
ÎÎÎÎÎ
W/RB
MBB
ÌÌÌÌÌÌÌ
ÎÎÎÎ ÌÌÌ
ÏÏÏÏ
ÏÏÏÏ
tsu(EN)
ENB
ten
B0 – B35
th(EN)
tpd(M-DV)
tpd(C-MR)
W1 (remains valid in mail1 register after read)
FIFO1 Output Register
Figure 15. Timing for Mail1 Register and MBF1 Flag
20
tdis
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN74ACT3632
512 × 36 × 2
CLOCKED BIDIRECTIONAL FIRST-IN, FIRST-OUT MEMORY
SCAS224D – JUNE 1992 – REVISED APRIL 1998
CLKB
th(EN)
tsu(EN)
CSB
W/RB
MBB
ENB
ÌÌÌÌÌÌÌ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏ
tsu(D)
B0 – B35
ÎÎÎ
ÏÏÏ
ÏÏÏ
ÏÏÏ
ÏÏÏ
ÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏ
th(D)
W1
CLKA
tpd(C-MF)
tpd(C-MF)
MBF2
CSA
W/RA
ÌÌÌÌ
MBA
ÎÎÎÎÎÎ
ÎÎÎÎ ÌÌÌÌ
ÏÏÏÏ
ÏÏÏÏ
tsu(EN)
ENA
ten
A0 – A35
th(EN)
tpd(M-DV)
tpd(C-MR)
tdis
W1 (remains valid in mail2 register after read)
FIFO2 Output Register
Figure 16. Timing for Mail2 Register and MBF2 Flag
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
21
SN74ACT3632
512 × 36 × 2
CLOCKED BIDIRECTIONAL FIRST-IN, FIRST-OUT MEMORY
SCAS224D – JUNE 1992 – REVISED APRIL 1998
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to 7 V
Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to VCC + 0.5 V
Output voltage range, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to VCC + 0.5 V
Input clamp current, IIK (VI < 0 or VI > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 20 mA
Output clamp current, IOK (VO < 0 or VO > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 50 mA
Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 50 mA
Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 400 mA
Package thermal impedance, θJA (see Note 2): PCB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28°C/W
PQ package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46°C/W
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The input and output voltage ratings may be exceeded provided the input and output current ratings are observed.
2. The package thermal impedance is calculated in accordance with JESD 51.
recommended operating conditions
MIN
MAX
4.5
5.5
UNIT
VCC
VIH
Supply voltage
VIL
IOH
Low-level input voltage
0.8
V
High-level output current
–4
mA
IOL
TA
Low-level output current
8
mA
70
°C
22
High-level input voltage
2
Operating free-air temperature
0
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
V
V
SN74ACT3632
512 × 36 × 2
CLOCKED BIDIRECTIONAL FIRST-IN, FIRST-OUT MEMORY
SCAS224D – JUNE 1992 – REVISED APRIL 1998
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
VOH
VOL
VCC = 4.5 V,
VCC = 4.5 V,
IOH = – 4 mA
IOL = 8 mA
II
IOZ
VCC = 5.5 V,
VCC = 5.5 V,
VI = VCC or 0
VO = VCC or 0
ICC
VCC = 5.5 V,
VI = VCC – 0.2 V or 0
∆ICC‡
MIN
TYP†
VCC = 5.5
5 5 V,
V
One
O input
i
t att 3.4
34V
V,
Other in
uts at VCC or GND
inputs
Co
VI = 0,
VO = 0,
UNIT
V
0.5
V
±5
µA
±5
µA
400
µA
mA
CSA = VIH
A0 – A35
0
CSB = VIH
B0 – B35
0
CSA = VIL
A0 – A35
1
CSB = VIL
B0 – B35
1
All other inputs
Ci
MAX
2.4
1
f = 1 MHz
4
pF
f = 1 MHz
8
pF
† All typical values are at VCC = 5 V, TA = 25°C.
‡ This is the supply current when each input is at one of the specified TTL voltage levels rather than 0 V or VCC.
timing requirements over recommended ranges of supply voltage and operating free-air
temperature (see Figures 1 through 17)
’ACT3632-15
MIN
fclock
tc
Clock frequency, CLKA or CLKB
tw(CLKH)
tw(CLKL)
tsu(D)
tsu(EN)
tsu(RS)
tsu(FS)
th(D)
th(EN)
th(RS)
th(FS)
MAX
’ACT3632-20
MIN
66.7
Clock cycle time, CLKA or CLKB
MAX
’ACT3632-30
MIN
50
MAX
33.4
UNIT
MHz
15
20
30
ns
Pulse duration, CLKA and CLKB high
6
8
10
ns
Pulse duration, CLKA and CLKB low
6
8
10
ns
Setup time, A0 – A35 before CLKA↑ and B0 – B35 before CLKB↑
4
5
6
ns
4.5
5
6
ns
Setup time, CSA, W/RA, ENA, and MBA before CLKA↑; CSB,
W/RB, ENB, and MBB before CLKB↑
Setup time, RST1 or RST2 low before CLKA↑ or CLKB↑§
Setup time, FS0 and FS1 before RST1 and RST2 high
Hold time, A0 – A35 after CLKA↑ and B0 – B35 after CLKB↑
Hold time, CSA, W/RA, ENA, and MBA after CLKA↑; CSB, W/RB,
ENB, and MBB after CLKB↑
Hold time, RST1 or RST2 low after CLKA↑ or CLKB↑§
Hold time, FS0 and FS1 after RST1 and RST2 high
5
6
7
ns
7.5
8.5
9.5
ns
1
1
1
ns
1
1
1
ns
4
4
5
ns
2
3
3
ns
tsk1¶
Skew time between CLKA↑ and CLKB↑ for ORA, ORB,
IRA, and IRB
7.5
9
11
ns
tsk2¶
Skew time between CLKA↑ and CLKB↑ for AEA, AEB,
AFA, and AFB
12
16
20
ns
§ Requirement to count the clock edge as one of at least four needed to reset a FIFO
¶ Skew time is not a timing constraint for proper device operation and is included only to illustrate the timing relationship between CLKA cycle and
CLKB cycle.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
23
SN74ACT3632
512 × 36 × 2
CLOCKED BIDIRECTIONAL FIRST-IN, FIRST-OUT MEMORY
SCAS224D – JUNE 1992 – REVISED APRIL 1998
switching characteristics over recommended ranges of supply voltage and operating free-air
temperature, CL = 30 pF (see Figures 1 through 17)
’ACT3632-15
PARAMETER
fmax
ta
MIN
MAX
66.7
’ACT3632-20
MIN
MAX
50
’ACT3632-30
MIN
MAX
33.4
UNIT
MHz
Access time, CLKA↑ to A0 – A35 and CLKB↑ to B0 – B35
3
11
3
13
3
15
ns
tpd(C-IR)
tpd(C-OR)
Propagation delay time, CLKA↑ to IRA and CLKB↑ to IRB
2
8
2
10
2
12
ns
Propagation delay time, CLKA↑ to ORA and CLKB↑ to ORB
1
8
1
10
1
12
ns
tpd(C-AE)
tpd(C-AF)
Propagation delay time, CLKA↑ to AEA and CLKB↑ to AEB
1
8
1
10
1
12
ns
Propagation delay time, CLKA↑ to AFA and CLKB↑ to AFB
1
8
1
10
1
12
ns
0
8
0
10
0
12
ns
3
13.5
3
15
3
17
ns
tpd(C-MR)
Propagation delay time, CLKA↑ to MBF1 low or MBF2 high and
CLKB↑ to MBF2 low or MBF1 high
Propagation delay time, CLKA↑ to B0 – B35† and CLKB↑ to
A0 – A35‡
tpd(M-DV)
Propagation delay time, MBA to A0 – A35 valid and MBB to
B0 – B35 valid
3
11
3
13
3
15
ns
tpd(R-F)
Propagation delay time, RST1 low to AEB low, AFA high, and
MBF1 high, and RST2 low to AEA low, AFB high, and MBF2 high
1
15
1
20
1
30
ns
ten
Enable time, CSA and W/RA low to A0 – A35 active and CSB low
and W/RB high to B0 – B35 active
2
12
2
13
2
14
ns
tdis
Disable time, CSA or W/RA high to A0 – A35 at high impedance
and CSB high or W/RB low to B0 – B35 at high impedance
1
8
1
12
1
11
ns
tpd(C-MF)
† Writing data to the mail1 register when the B0 – B35 outputs are active and MBB is high
‡ Writing data to the mail2 register when the A0 – A35 outputs are active and MBA is high
24
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN74ACT3632
512 × 36 × 2
CLOCKED BIDIRECTIONAL FIRST-IN, FIRST-OUT MEMORY
SCAS224D – JUNE 1992 – REVISED APRIL 1998
PARAMETER MEASUREMENT INFORMATION
5V
1.1 kΩ
From Output
Under Test
30 pF
(see Note A)
680 Ω
LOAD CIRCUIT
3V
Timing
Input
3V
High-Level
Input
1.5 V
1.5 V
1.5 V
GND
GND
th
tsu
Data,
Enable
Input
tw
3V
1.5 V
3V
1.5 V
Low-Level
Input
GND
1.5 V
GND
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
Output
Enable
1.5 V
VOLTAGE WAVEFORMS
PULSE DURATIONS
3V
1.5 V
1.5 V
GND
tPLZ
Low-Level
Output
tPZL
≈3V
1.5 V
VOL
3V
≈0V
tpd
tpd
VOH
1.5 V
1.5 V
GND
tPZH
High-Level
Output
1.5 V
Input
VOH
In-Phase
Output
1.5 V
1.5 V
VOL
tPHZ
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
NOTES: A. Includes probe and jig capacitance
B. tPZL and tPZH are the same as ten.
C. tPLZ and tPHZ are the same as tdis.
Figure 17. Load Circuit and Voltage Waveforms
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
25
SN74ACT3632
512 × 36 × 2
CLOCKED BIDIRECTIONAL FIRST-IN, FIRST-OUT MEMORY
SCAS224D – JUNE 1992 – REVISED APRIL 1998
TYPICAL CHARACTERISTICS
SUPPLY CURRENT
vs
CLOCK FREQUENCY
I CC(f) – Supply Current – mA
300
fdata = 1/2 fclock
TA = 75°C
CL = 0 pF
250
VCC = 5.5 V
200
VCC = 5 V
150
VCC = 4.5 V
100
50
0
0
10
20
30
40
50
fclock – Clock Frequency – MHz
Figure 18
26
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
60
70
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright  1999, Texas Instruments Incorporated