SONY ΣRAM™ CXK79M36C162GB 18Mb 1x2Lp HSTL High Speed Synchronous SRAMs (512Kb x 36) 33/4/5 Preliminary Description The CXK79M36C162GB is a high speed CMOS synchronous static RAM with common I/O pins. It is manufactured in compliance with the JEDEC-standard 209 pin BGA package pinout defined for SigmaRAM™ devices. It integrates input registers, high speed RAM, output registers, and a two-deep write buffer onto a single monolithic IC. Double Data Rate (DDR) Pipelined (PL) read operations and Late Write (LW) write operations are supported, providing a high-performance user interface. Positive and negative output clocks are provided for applications requiring source-synchronous operation. All address and control input signals are registered on the rising edge of the CK differential input clock. During read operations, output data is driven valid twice, from both the rising and falling edges of CK, beginning one full cycle after the address and control signals are registered. During write operations, input data is registered twice, on both the rising and falling edges of CK, beginning one full cycle after the address and control signals are registered. Because two pieces of data are always transferred during read and write operations, the least significant address bit of the internal memory array is not available as an external address pin to this device. Consequently, the number of external address pins available to the device is one less than the specified depth of the device (i.e. the 512Kb x 36 device has 18, not 19, external address pins). And, the user cannot choose the order in which the two pieces of data are read. Read data is always provided in the same order in which it is written. Output drivers are series-terminated, and output impedance is programmable via the ZQ control pin. When an external resistor RQ is connected between ZQ and VSS, the impedance of the SRAM’s output drivers is set to ~RQ/5. 300 MHz operation (600 Mbps) is obtained from a single 1.8V power supply. JTAG boundary scan interface is provided using a subset of IEEE standard 1149.1 protocol. Features • 3 Speed Bins Cycle Time / Data Access Time -33 3.3ns / 1.8ns -4 4.0ns / 2.1ns -5 5.0ns / 2.3ns • Single 1.8V power supply (VDD): 1.7V (min) to 1.95V (max) • Dedicated output supply voltage (VDDQ): 1.4V (min) to VDD (max) • HSTL-compatible I/O interface with dedicated input reference voltage (VREF): VDDQ/2 typical • Common I/O • Double Data Rate (DDR) data transfers • Pipelined (PL) read operations • Late Write (LW) write operations • Burst capability with internally controlled Linear Burst address sequencing • Burst length of two or four, with automatic address wrap • Full read/write data coherency • Differential input clocks (CK and CK) • Data-referenced output clocks (CQ1, CQ1, CQ2, CQ2) • Programmable output driver impedance via dedicated control pin (ZQ) • Depth expansion capability (2 or 4 banks) via programmable chip enables (E2, E3, EP2, EP3) • JTAG boundary scan (subset of IEEE standard 1149.1) • 209 pin (11x19), 1mm pitch, 14mm x 22mm Ball Grid Array (BGA) package 18Mb 1x2Lp, HSTL, rev 1.1 1 / 25 November 8, 2002 SONY® ΣRAM Preliminary CXK79M36C162GB 512Kb x 36 Pin Assignment (Top View) 1 2 3 4 5 6 7 8 9 10 11 A NC NC A E2 A ADV A E3 A DQ DQ B NC NC MCL (2) NC A (x36) W A MCL (2) NC DQ DQ C NC NC NC MCL (2) NC (144M) E1 NC NC MCL (2) DQ DQ D NC NC VSS VREF NC MCL NC VREF VSS DQ DQ E NC DQ VDDQ VDDQ VDD VDD VDD VDDQ VDDQ NC DQ F DQ DQ VSS VSS VSS ZQ VSS VSS VSS NC NC G DQ DQ VDDQ VDDQ VDD EP2 VDD VDDQ VDDQ NC NC H DQ DQ VSS VSS VSS EP3 VSS VSS VSS NC NC J DQ DQ VDDQ VDDQ VDD MCH VDD VDDQ VDDQ NC NC K CQ2 CQ2 CK CK VSS MCL VSS NC NC CQ1 CQ1 L NC NC VDDQ VDDQ VDD MCL VDD VDDQ VDDQ DQ DQ M NC NC VSS VSS VSS MCH VSS VSS VSS DQ DQ N NC NC VDDQ VDDQ VDD MCH VDD VDDQ VDDQ DQ DQ P NC NC VSS VSS VSS MCL VSS VSS VSS DQ DQ R DQ NC VDDQ VDDQ VDD VDD VDD VDDQ VDDQ DQ NC T DQ DQ VSS VREF NC MCL NC VREF VSS NC NC U DQ DQ NC A NC (72M) A NC (36M) A NC NC NC V DQ DQ A A A A1 A A A NC NC W DQ DQ TMS TDI A MCL (1) A TDO TCK NC NC Notes: 1: Pin 6W is defined as Address Pin A0 in Single Data Rate (SDR) Common I/O SigmaRAMs. However, it must be tied “low” in this device. The least significant address bit of the internal memory array is not available as an externally controlled address pin in Double Data Rate (DDR) Common I/O SigmaRAMs. 2. Pins 3B, 4C, 8B, and 9C are defined as Byte Write Enable Pins Bx in x36 Single Data Rate (SDR) Common I/O SigmaRAMs. However, they must be tied “low” in this device. Byte Write functionality is not supported in Double Data Rate (DDR) Common I/O SigmaRAMs. 18Mb 1x2Lp, HSTL, rev 1.1 2 / 25 November 8, 2002 SONY® ΣRAM CXK79M36C162GB Preliminary Pin Description Symbol Type Quantity Description A Input 17 Address Inputs - Registered on the rising edge of CK. A1 Input 1 Address Input 1 - Registered on the rising edge of CK. Initializes burst counter. DQ I/O 36 Data Inputs / Outputs - Registered on the rising and falling edges of CK during write operations. Driven from the rising and falling edges of CK during read operations. CK, CK Input 2 Differential Input Clocks CQ1, CQ1 CQ2, CQ2 Output 4 Output Clocks E1 Input 1 Chip Enable Control Input - Registered on the rising edge of CK. E1 = 0 enables the device to accept read and write commands. E1 = 1 disables the device. See the Clock Truth Table section for further information. E2, E3 Input 2 Programmable Chip Enable Control Inputs - Registered on the rising edge of CK. See the Clock Truth Table and Depth Expansion sections for further information. EP2, EP3 Input 2 Programmable Chip Enable Active-Level Select Inputs - These pins must be tied “high” or “low” at power-up. See the Clock Truth Table and Depth Expansion sections for further information. ADV Input 1 Address Advance Control Input - Registered on the rising edge of CK. ADV = 0 loads a new address and begins a new operation when the device is enabled. ADV = 1 increments the address and continues the previous operation when the device is enabled. See the Clock Truth Table section for further information. W Input 1 Write Enable Control Input - Registered on the rising edge of CK. W = 0 specifies a write operation when ADV = 0 and the device is enabled. W = 1 specifies a read operation when ADV = 0 and the device is enabled. See the Clock Truth Table section for further information. ZQ Input 1 Output Impedance Control Resistor Input - This pin must be tied to VSS through an external resistor RQ at power-up. Output driver impedance is set to one-fifth the value of RQ, nominally. See the Output Driver Impedance Control section for further information. VDD 14 1.8V Core Power Supply - Core supply voltage. VDDQ 24 Output Power Supply - Output buffer supply voltage. VREF 4 Input Reference Voltage - Input buffer threshold voltage. VSS 30 Ground TCK Input 1 JTAG Clock TMS Input 1 JTAG Mode Select - Weakly pulled “high” internally. TDI Input 1 JTAG Data In - Weakly pulled “high” internally. TDO Output 1 JTAG Data Out MCL *Input* 10 Must Connect “Low” - May not be actual input pins. MCH *Input* 3 Must Connect “High” - May not be actual input pins. 52 No Connect - These pins are true no-connects, i.e. there is no internal chip connection to these pins. They can be left unconnected or tied directly to VSS. NC 18Mb 1x2Lp, HSTL, rev 1.1 3 / 25 November 8, 2002 SONY® ΣRAM Preliminary CXK79M36C162GB Clock Truth Table CK E1 E ADV W (tn) (tn) (tn) (tn) Previous Operation ↑ X F 0 X X ↑ X X 1 X Bank Deselect ↑ 1 T 0 X X ↑ X X 1 X Deselect ↑ 0 T 0 0 X ↑ X X 1 X Write ↑ 0 T 0 1 X ↑ X X 1 X Read Current Operation DQ/CQ (tn) DQ/CQ (tn+½) DQ/CQ (tn+1) DQ/CQ (tn+1½) Bank Deselect *** Hi-Z Bank Deselect (Continue) Hi-Z Hi-Z Deselect *** Hi-Z/CQ Hi-Z/CQ Hi-Z/CQ Deselect (Continue) Write Loads new address Write Continue Increments address by 2 Read Loads new address Read Continue Increments address by 2 *** *** D1/CQ D2/CQ D1/CQ D2/CQ D3/CQ D4/CQ *** *** Q1/CQ Q2/CQ Q1/CQ Q2/CQ Q3/CQ Q4/CQ Notes: 1. “1” = input “high”; “0” = input “low”; “X” = input “don’t care”; “T” = input “true”; “F” = input “false”. 2. “***” indicates that the DQ input requirement or output state and the CQ output state are determined by the previous operation. 3. If E2 = EP2 and E3 = EP3 then E = “T” else E = “F”. 4. DQs are tri-stated in response to Bank Deselect, Deselect, and Write commands, one full cycle after the command is sampled. 5. CQs are tri-stated in response to Bank Deselect commands only, one full cycle after the command is sampled. 6. One (1) Continue operation may be initiated after a Read or Write operation is initiated to burst transfer four (4) distinct pieces of data per single external address input. If a second (2nd) Continue operation is initiated, the internal address wraps back to the initial external (base) address. 18Mb 1x2Lp, HSTL, rev 1.1 4 / 25 November 8, 2002 SONY® ΣRAM Preliminary CXK79M36C162GB State Diagram X,F,0,X or X,X,1,X Bank Deselect 0,T,0,1 0,T,0,0 1,T,0,X X,F,0,X Deselect 0,T,0,1 0,T,0,0 1,T,0,X or X,X,1,X 1,T,0,X 1,T,0,X 0,T,0,0 Read Write 0,T,0,1 X,F,0,X 0,T,0,1 X,X,1,X X,X,1,X 0,T,0,1 1,T,0,X X,F,0,X Read Continue X,F,0,X 0,T,0,0 0,T,0,0 0,T,0,0 0,T,0,1 X,X,1,X Write Continue 1,T,0,X X,F,0,X X,X,1,X Notes: 1. The notation “X,X,X,X” controlling the state transitions above indicate the states of inputs E1, E, ADV, and W respectively. 2. “1” = input “high”; “0” = input “low”; “X” = input “don’t care”; “T” = input “true”; “F” = input “false”. 3. If E2 = EP2 and E3 = EP3 then E = “T” else E = “F”. 18Mb 1x2Lp, HSTL, rev 1.1 5 / 25 November 8, 2002 SONY® ΣRAM CXK79M36C162GB Preliminary •Burst (Continue) Operations Because two pieces of data are always transferred during read and write operations, the least significant address bit (A0) of the internal memory array is not available as an external address pin to these devices. Rather, the address bit is set to “0” internally prior to the first data transfer and set to “1” internally prior to the second data transfer. Consequently, the two pieces of data transferred during read and write operations are always read in the same address sequence in which they are written. Burst operations follow the simple address sequence depicted in the table below: A1 A1 Sequence Key 1st (Base) Address 0 1 A1 2nd Address 1 0 A1 One (1) Continue operation may be initiated after a Read or Write operation is initiated to burst transfer four (4) distinct pieces of data per single external address input. If a second (2nd) Continue operation is initiated, the internal address wraps back to the initial external (base) address. •Depth Expansion Depth expansion in these devices is supported via programmable chip enables E2 and E3. The active levels of E2 and E3 are programmable through the static inputs EP2 and EP3 respectively. When EP2 is tied “high”, E2 functions as an active-high input. When EP2 is tied “low”, E2 functions as an active-low input. Similarly, when EP3 is tied “high”, E3 functions as an active-high input. And, when EP3 is tied “low”, E3 functions as an active-low input. The programmability of E2 and E3 allows four banks of depth expansion to be accomplished with no additional logic. By programming E2 and E3 of four devices in a binary sequence (00, 01, 10, 11), and by driving E2 and E3 with external address signals, the four devices can be made to look like one larger device. When these devices are deselected via chip enable E1, the output clocks continue to toggle. However, when these devices are deselected via programmable chip enables E2 or E3, the output clocks are forced to a Hi-Z state. See the Clock Truth Table for further information. •Output Driver Impedance Control The impedance of the data and clock output drivers in these devices can be controlled via the static input ZQ. When an external impedance matching resistor (RQ) is connected between ZQ and VSS, output driver impedance is set to one-fifth the value of the resistor, nominally. See the DC Electrical Characteristics section for further information. Output driver impedance is updated whenever the data output drivers are in an inactive (High-Z) state. See the Clock Truth Table section for information concerning which commands deactivate the data output drivers. At power up, 8192 clock cycles followed by any command that deactivates the data output drivers are required to ensure that the output impedance has reached the desired value. Note: The impedance of the output drivers will drift somewhat due to changes in temperature and voltage. Consequently, during operation, the output drivers should be deactivated periodically in order to update the output impedance and ensure that it remains within specified tolerances. •Power-Up Sequence For reliability purposes, Sony recommends that power supplies power up in the following sequence: VSS, VDD, VDDQ, VREF, and Inputs. VDDQ should never exceed VDD. If this power supply sequence cannot be met, a large bypass diode may be required between VDD and VDDQ. Please contact Sony Memory Application Department for further information. 18Mb 1x2Lp, HSTL, rev 1.1 6 / 25 November 8, 2002 SONY® ΣRAM Preliminary CXK79M36C162GB •Absolute Maximum Ratings Parameter Symbol Rating Units Supply Voltage VDD -0.5 to +2.5 V Output Supply Voltage VDDQ -0.5 to +2.3 V VIN -0.5 to VDDQ+0.5 (2.3V max) V Input Voltage (EP2, EP3) (MCH pins 6J, 6M, 6N) (MCL pins 6D, 6K, 6L, 6P, 6T) VMIN -0.5 to VDD+0.5 (2.5V max) V Input Voltage (TCK, TMS, TDI) VTIN -0.5 to VDD+0.5 (2.5V max) V Operating Temperature TA 0 to 85 °C Junction Temperature TJ 0 to 110 °C Storage Temperature TSTG -55 to 150 °C Input Voltage (Address, Control, Data, Clock) (MCL pins 3B, 8B, 4C, 9C, 6W) Note: Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at these or any other conditions other than those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. •BGA Package Thermal Characteristics Parameter Junction to Case Temperature Symbol Rating Units ΘJC 3.6 °C/W •I/O Capacitance (TA = 25oC, f = 1 MHz) Parameter Input Capacitance Symbol Test conditions Min Max Units Address CIN VIN = 0V --- 3.5 pF Control CIN VIN = 0V --- 3.5 pF CK Clock CKIN VKIN = 0V --- 4.0 pF Data COUT VOUT = 0V --- 4.5 pF CQ Clock COUT VOUT = 0V --- 4.5 pF Output Capacitance Note: These parameters are sampled and are not 100% tested. 18Mb 1x2Lp, HSTL, rev 1.1 7 / 25 November 8, 2002 SONY® ΣRAM Preliminary CXK79M36C162GB •DC Recommended Operating Conditions Parameter (VSS = 0V, TA = 0 to 85oC) Symbol Min Typ Max Units Notes Supply Voltage VDD 1.7 1.8 1.95 V Output Supply Voltage VDDQ 1.4 --- VDD V Input Reference Voltage VREF VDDQ/2 - 0.1 VDDQ/2 VDDQ/2 + 0.1 V 1 Input High Voltage (Address, Control, Data) VIH VREF + 0.2 --- VDDQ + 0.3 V 2 Input Low Voltage (Address, Control, Data) VIL -0.3 --- VREF - 0.2 V 3 Input High Voltage (EP2, EP3, MCH) VMIH VREF + 0.3 --- VDD + 0.3 V Input Low Voltage (EP2, EP3, MCL) VMIL -0.3 --- VREF - 0.3 V Clock Input Signal Voltage VKIN -0.3 --- VDDQ + 0.3 V Clock Input Differential Voltage VDIF 0.4 --- VDDQ + 0.6 V Clock Input Common Mode Voltage VCM VDDQ/2 - 0.1 VDDQ/2 VDDQ/2 + 0.1 V 2,3 1. The peak-to-peak AC component superimposed on VREF may not exceed 5% of the DC component. 2. VIH (max) AC = VDDQ + 0.9V for pulse widths less than one-quarter of the cycle time (tCYC/4). 3. VIL (min) AC = -0.9V for pulse widths less than one-quarter of the cycle time (tCYC/4). 18Mb 1x2Lp, HSTL, rev 1.1 8 / 25 November 8, 2002 SONY® ΣRAM Preliminary CXK79M36C162GB •DC Electrical Characteristics Parameter Symbol Input Leakage Current (Address, Control, Clock) ILI Input Leakage Current (EP2, EP3) (VDD = 1.8V ± 0.1V, VSS = 0V, TA = 0 to 85oC) Test Conditions Min Typ Max Units VIN = VSS to VDDQ -5 --- 5 uA IMLI1 VMIN = VSS to VDD -10 --- 10 uA Input Leakage Current (MCH) IMLI2 VMIN = VMIH (min) to VDD -10 --- 10 uA Input Leakage Current (MCL) IMLI3 VMIN = VSS to VMIL (max) -10 --- 10 uA VOUT = VSS to VDDQ -10 --- 10 uA Output Leakage Current ILO Average Power Supply Operating Current IDD-33 IDD-4 IDD-5 IOUT = 0 mA VIN = VIH or VIL ------- ------- 750 650 550 mA Power Supply Deselect Operating Current IDD2 IOUT = 0 mA VIN = VIH or VIL --- --- 250 mA Output High Voltage VOH IOH = -7.0 mA RQ = 250Ω VDDQ - 0.4 --- --- V Output Low Voltage VOL IOL = 7.0 mA RQ = 250Ω --- --- 0.4 V --- --- 35 Ω VOH, VOL = VDDQ/2 150Ω ≤ RQ ≤ 300Ω (RQ/5)* 0.85 RQ/5 (RQ/5)* 1.15 Ω VOH, VOL = VDDQ/2 51 --- --- Ω VOH, VOL = VDDQ/2 RQ < 150Ω Output Driver Impedance ROUT RQ > 300Ω (60*0.85) (30*1.15) Notes 1 2 1. For maximum output drive (i.e. minimum impedance), the ZQ pin can be tied directly to VSS. 2. For minimum output drive (i.e. maximum impedance), the ZQ pin can be left unconnected or tied directly to VDDQ. 18Mb 1x2Lp, HSTL, rev 1.1 9 / 25 November 8, 2002 SONY® ΣRAM Preliminary CXK79M36C162GB •AC Electrical Characteristics (VDD = 1.8V ± 0.1V, VSS = 0V, TA = 0 to 85oC) -33 Parameter -4 -5 Symbol Units Notes Min Max Min Max Min Max Input Clock Cycle Time tKHKH 3.3 --- 4.0 --- 5.0 --- ns Input Clock High Pulse Width tKHKL 1.3 --- 1.5 --- 2.0 --- ns Input Clock Low Pulse Width tKLKH 1.3 --- 1.5 --- 2.0 --- ns Address Input Setup Time tAVKH 0.7 --- 0.8 --- 1.0 --- ns Address Input Hold Time tKHAX 0.4 --- 0.5 --- 0.5 --- ns Control Input Setup Time tBVKH 0.7 --- 0.8 --- 1.0 --- ns 1 Control Input Hold Time tKHBX 0.4 --- 0.5 --- 0.5 --- ns 1 Data Input Setup Time tDVKH tDVKL 0.35 --- 0.4 --- 0.45 --- ns Data Input Hold Time tKHDX tKLDX 0.3 --- 0.35 --- 0.4 --- ns Input Clock High to Output Data Valid Input Clock Low to Output Data Valid tKHQV tKLQV --- 1.8 --- 2.1 --- 2.3 ns Input Clock High to Output Data Hold Input Clock Low to Output Data Hold tKHQX tKLQX 0.5 --- 0.5 --- 0.5 --- ns 2 Input Clock High to Output Data Low-Z tKHQX1 0.5 --- 0.5 --- 0.5 --- ns 2,3 Input Clock High to Output Data High-Z tKHQZ --- 1.8 --- 2.1 --- 2.3 ns 2,3 Input Clock High to Output Clock High Input Clock Low to Output Clock Low tKHCH tKLCL 0.5 1.8 0.5 2.1 0.5 2.3 ns Input Clock High to Output Clock Low-Z tKHCX1 0.5 --- 0.5 --- 0.5 --- ns 2,3 Input Clock High to Output Clock High-Z tKHCZ --- 1.8 --- 2.1 --- 2.3 ns 2,3 Output Clock High to Output Data Valid Output Clock Low to Output Data Valid tCHQV tCLQV --- 0.25 --- 0.25 --- 0.3 ns 2 Output Clock High to Output Data Hold Output Clock Low to Output Data Hold tCHQX tCLQX -0.25 --- -0.25 --- -0.3 --- ns 2 All parameters are measured from the mid-point of the object signal to the mid-point of the reference signal, unless otherwise noted. 1. These parameters apply to control inputs E1, E2, E3, ADV, and W. 2. These parameters are guaranteed by design through extensive corner lot characterization. 3. These parameters are measured at ± 50mV from steady state voltage. 18Mb 1x2Lp, HSTL, rev 1.1 10 / 25 November 8, 2002 SONY® ΣRAM CXK79M36C162GB Preliminary •AC Electrical Characteristics (Note) The four AC timing parameters listed below are tested according to specific combinations of Output Clocks (CQs) and Output Data (DQs): 1. tCHQV - Output Clock High to Output Data Valid (max) 2. tCLQV - Output Clock Low to Output Data Valid (max) 3. tCHQX - Output Clock High to Output Data Hold (min) 4. tCLQX - Output Clock Low to Output Data Hold (min) The specific CQ / DQ combinations are defined as follows: 512Kb x 36 CQs 1K, 2K DQs 2E, 1F, 2F, 1G, 2G, 1H, 2H, 1J, 2J, 1R, 1T, 2T, 1U, 2U, 1V, 2V, 1W, 2W 10K, 11K 10A, 11A, 10B, 11B, 10C, 11C, 10D, 11D, 11E, 10L, 11L, 10M, 11M, 10N, 11N, 10P, 11P, 10R 18Mb 1x2Lp, HSTL, rev 1.1 11 / 25 November 8, 2002 SONY® ΣRAM Preliminary CXK79M36C162GB •AC Test Conditions (VDDQ = 1.8V) Parameter (VDD = 1.8V ± 0.1V, VDDQ = 1.8V ± 0.1V, TA = 0 to 85°C) Symbol Conditions Units VREF 0.9 V Input High Level VIH 1.4 V Input Low Level VIL 0.4 V Input Rise & Fall Time 2.0 V/ns Input Reference Level 0.9 V Input Reference Voltage Notes Clock Input High Voltage VKIH 1.4 V VDIF = 1.0V Clock Input Low Voltage VKIL 0.4 V VDIF = 1.0V Clock Input Common Mode Voltage VCM 0.9 V Clock Input Rise & Fall Time 2.0 V/ns Clock Input Reference Level CK/CK cross V Output Reference Level 0.9 V Output Load Conditions RQ = 250Ω See Figure 1 below Figure 1: AC Test Output Load (VDDQ = 1.8V) 0.9 V 16.7 Ω 50 Ω 50 Ω 5 pF DQ 16.7 Ω 0.9 V 16.7 Ω 50 Ω 50 Ω 5 pF 18Mb 1x2Lp, HSTL, rev 1.1 12 / 25 November 8, 2002 SONY® ΣRAM Preliminary CXK79M36C162GB •AC Test Conditions (VDDQ = 1.5V) Parameter (VDD = 1.8V ± 0.1V, VDDQ = 1.5V ± 0.1V, TA = 0 to 85°C) Symbol Conditions Units VREF 0.75 V Input High Level VIH 1.25 V Input Low Level VIL 0.25 V Input Rise & Fall Time 2.0 V/ns Input Reference Level 0.75 V Input Reference Voltage Notes Clock Input High Voltage VKIH 1.25 V VDIF = 1.0V Clock Input Low Voltage VKIL 0.25 V VDIF = 1.0V Clock Input Common Mode Voltage VCM 0.75 V Clock Input Rise & Fall Time 2.0 V/ns Clock Input Reference Level CK/CK cross V Output Reference Level 0.75 V Output Load Conditions RQ = 250Ω See Figure 2 below Figure 2: AC Test Output Load (VDDQ = 1.5V) 0.75 V 16.7 Ω 50 Ω 50 Ω 5 pF DQ 16.7 Ω 0.75 V 16.7 Ω 50 Ω 50 Ω 5 pF 18Mb 1x2Lp, HSTL, rev 1.1 13 / 25 November 8, 2002 SONY® ΣRAM Preliminary CXK79M36C162GB One Bank Read-Write-Read Timing Diagram Figure 3 Read Read Continue Read Deselect Deselect Write Continue Write Write Read Deselect Deselect (Continue) CK CK tAVKH tKHAX A A1 A2 tKHKH A3 tKHKL tKLKH A4 A5 tBVKH tKHBX E1 ADV W tKLQV tKHQV tKLQX tKHQX tKHQZ tKHQX1 tDVKH tKHDX Q11 Q12 Q13 Q14 Q21 Q22 tDVKL tKLDX Q51 Q52 D31 D32 D33 D34 D41 D42 DQ tCLQX tCHQX tCLQV tCHQV tKHCH tKLCL CQ CQ Note: In the diagram above, two Deselect operations are inserted between Read and Write operations to control the data bus transition from output to input. This depiction is for clarity purposes only. It is NOT a requirement. Depending on the application, one Deselect operation may be sufficient. Note: E1 = EP1 and E2 = EP2 in this example (not shown). 18Mb 1x2Lp, HSTL, rev 1.1 14 / 25 November 8, 2002 SONY® ΣRAM Preliminary CXK79M36C162GB Two Bank Read-Write-Read Timing Diagram Figure 4 B1: B2: Read Write B-Deselect B-Deselect B-Deselect R-Continue B-Deselect Deselect B-Deselect B-Deselect B-Deselect B-Deselect B-Deselect Read B-Deselect Deselect Write W-Continue B-Deselect Read Deselect Deselect CK CK A A1 A2 A3 A4 A5 E2 E1 ADV W Q11 Q12 Q13 Q14 DQ (B1) D41 D42 Q21 Q22 Q51 Q52 DQ (B2) D31 D32 D33 D34 tKHCZ tKHCX1 CQ (B1) CQ (B1) CQ (B2) CQ (B2) Note: In the diagram above, two Deselect operations are inserted between Read and Write operations to control the data bus transition from output to input. This depiction is for clarity purposes only. It is NOT a requirement. Depending on the application, one Deselect operation may be sufficient. Note: Bank 1 EP1 = “low”, Bank 2 EP1 “high”, and Bank 1 and Bank 2 E2 = EP2 in this example (not shown). 18Mb 1x2Lp, HSTL, rev 1.1 15 / 25 November 8, 2002 SONY® ΣRAM Preliminary CXK79M36C162GB •Test Mode Description These devices provide a JTAG Test Access Port (TAP) and Boundary Scan interface using a limited set of IEEE std. 1149.1 functions. This test mode is intended to provide a mechanism for testing the interconnect between master (processor, controller, etc.), SRAMs, other components, and the printed circuit board. In conformance with a subset of IEEE std. 1149.1, these devices contain a TAP Controller and four TAP Registers. The TAP Registers consist of one Instruction Register and three Data Registers (ID, Bypass, and Boundary Scan Registers). The TAP consists of the following four signals: TCK: TMS: TDI: TDO: Test Clock Test Mode Select Test Data In Test Data Out Induces (clocks) TAP Controller state transitions. Inputs commands to the TAP Controller. Sampled on the rising edge of TCK. Inputs data serially to the TAP Registers. Sampled on the rising edge of TCK. Outputs data serially from the TAP Registers. Driven from the falling edge of TCK. Disabling the TAP When JTAG is not used, TCK should be tied “low” to prevent clocking the SRAM. TMS and TDI should either be tied “high” through a pull-up resistor or left unconnected. TDO should be left unconnected. Note: Operation of the TAP does not disrupt normal SRAM operation except when the EXTEST-A or SAMPLE-Z instruction is selected. Consequently, TCK, TMS, and TDI can be controlled any number of ways without adversely affecting the functionality of the device. JTAG DC Recommended Operating Conditions (VDD = 1.8V ± 0.1V, TA = 0 to 85°C) Parameter Symbol Test Conditions Min Max Units JTAG Input High Voltage (TCK, TMS, TDI) VTIH --- VDD/2 + 0.3 VDD + 0.3 V JTAG Input Low Voltage (TCK, TMS, TDI) VTIL --- -0.3 VDD/2 - 0.3 V JTAG Output High Voltage (TDO) VTOH ITOH = -100uA VDD - 0.1 --- V JTAG Output Low Voltage (TDO) VTOL ITOL = 100uA --- 0.1 V JTAG Output High Voltage (TDO) VTOH ITOH = -8mA VDD - 0.4 --- V JTAG Output Low Voltage (TDO) VTOL ITOL = 8mA --- 0.4 V JTAG Input Leakage Current ITLI VTIN = VSS to VDD -20 10 uA JTAG Output Leakage Current ITLO VTOUT = VSS to VDD -10 10 uA (VDD = 1.8V ± 0.1V, TA = 0 to 85°C) JTAG AC Test Conditions Parameter Symbol Conditions Units JTAG Input High Level VTIH 1.8 V JTAG Input Low Level VTIL 0.0 V JTAG Input Rise & Fall Time 1.0 V/ns JTAG Input Reference Level 0.9 V JTAG Output Reference Level 0.9 V JTAG Output Load Condition 18Mb 1x2Lp, HSTL, rev 1.1 Notes See Fig. 1 (page 12) 16 / 25 November 8, 2002 SONY® ΣRAM Preliminary CXK79M36C162GB JTAG AC Electrical Characteristics Parameter Symbol Min Max Units Notes TCK Cycle Time tTHTH 50 ns TCK High Pulse Width tTHTL 20 ns TCK Low Pulse Width tTLTH 20 ns TMS Setup Time tMVTH 5 ns TMS Hold Time tTHMX 5 ns TDI Setup Time tDVTH 5 ns TDI Hold Time tTHDX 5 ns Capture Setup Time (Address, Control, Data, Clock) tCS 5 ns 1 Capture Hold Time (Address, Control, Data, Clock) tCH 8 ns 1 TCK Low to TDO Valid tTLQV TCK Low to TDO Hold tTLQX 10 0 ns ns 1. These parameters are guaranteed by design through extensive corner lot characterization. JTAG Timing Diagram Figure 5 tTHTL tTLTH tTHTH TCK tMVTH tTHMX TMS tDVTH tTHDX TDI tTLQV tTLQX TDO 18Mb 1x2Lp, HSTL, rev 1.1 17 / 25 November 8, 2002 SONY® ΣRAM Preliminary CXK79M36C162GB TAP Controller The TAP Controller is a 16-state state machine that controls access to the various TAP Registers and executes the operations associated with each TAP Instruction. State transitions are controlled by TMS and occur on the rising edge of TCK. The TAP Controller enters the “Test-Logic Reset” state in one of two ways: 1. At power up. 2. When a logic “1” is applied to TMS for at least 5 consecutive rising edges of TCK. The TDI input receiver is sampled only when the TAP Controller is in either the “Shift-IR” state or the “Shift-DR” state. The TDO output driver is active only when the TAP Controller is in either the “Shift-IR” state or the “Shift-DR” state. TAP Controller State Diagram Figure 6 1 Test-Logic Reset 0 0 Run-Test / Idle 1 Select DR-Scan 1 Select IR-Scan 0 1 0 1 Capture-DR Capture-IR 0 0 0 Shift-DR 1 1 Exit1-DR Exit1-IR 0 0 0 Pause-DR 1 0 Exit2-IR 1 18Mb 1x2Lp, HSTL, rev 1.1 0 18 / 25 0 1 Update-DR 1 0 Pause-IR 1 Exit2-DR 0 Shift-IR 1 1 1 Update-IR 1 0 November 8, 2002 SONY® ΣRAM CXK79M36C162GB Preliminary TAP Registers TAP Registers are serial shift registers that capture serial input data (from TDI) on the rising edge of TCK, and drive serial output data (to TDO) on the subsequent falling edge of TCK. They are divided into two groups: “Instruction Registers” (IR), which are manipulated via the “IR” states in the TAP Controller, and “Data Registers” (DR), which are manipulated via the “DR” states in the TAP Controller. Instruction Register (IR - 3 bits) The Instruction Register stores the various TAP Instructions supported by these devices. It is loaded with the IDCODE instruction at power-up, and when the TAP Controller is in the “Test-Logic Reset” and “Capture-IR” states. It is inserted between TDI and TDO when the TAP Controller is in the “Shift-IR” state, at which time it can be loaded with a new instruction. However, newly loaded instructions are not executed until the TAP Controller has reached the “Update-IR” state. The Instruction Register is 3 bits wide, and is encoded as follows: Code (2:0) Instruction Description 000 EXTEST-A Loads the individual logic states of all signals composing the SRAM’s I/O ring into the Boundary Scan Register when the TAP Controller is in the “Capture-DR” state, and inserts the B-Scan Register between TDI and TDO when the TAP Controller is in the “Shift-DR” state. Also enables the SRAM’s data and clock output drivers, and moves the contents of the B-Scan Register associated with the data and clock output signals to the input side of the SRAM’s output register. The SRAM’s input clock can then be used to transfer the B-Scan Register contents directly to the data and clock output pins (the input clock controls the SRAM’s output register). Note that newly captured and/or shifted B-Scan Register contents do not appear at the input side of the SRAM’s output register until the TAP Controller has reached the “UpdateDR” state. See the Boundary Scan Register description for more information. 001 IDCODE Loads a predefined device- and manufacturer-specific identification code into the ID Register when the TAP Controller is in the “Capture-DR” state, and inserts the ID Register between TDI and TDO when the TAP Controller is in the “Shift-DR” state. See the ID Register description for more information. 010 SAMPLE-Z Loads the individual logic states of all signals composing the SRAM’s I/O ring into the Boundary Scan Register when the TAP Controller is in the “Capture-DR” state, and inserts the B-Scan Register between TDI and TDO when the TAP Controller is in the “Shift-DR” state. Also disables the SRAM’s data and clock output drivers. See the Boundary Scan Register description for more information. 011 PRIVATE Do not use. Reserved for manufacturer use only. 100 SAMPLE Loads the individual logic states of all signals composing the SRAM’s I/O ring into the Boundary Scan Register when the TAP Controller is in the “Capture-DR” state, and inserts the B-Scan Register between TDI and TDO when the TAP Controller is in the “Shift-DR” state. See the Boundary Scan Register description for more information. 101 PRIVATE Do not use. Reserved for manufacturer use only. 110 PRIVATE Do not use. Reserved for manufacturer use only. 111 BYPASS Loads a logic “0” into the Bypass Register when the TAP Controller is in the “Capture-DR” state, and inserts the Bypass Register between TDI and TDO when the TAP Controller is in the “Shift-DR” state. See the Bypass Register description for more information. Bit 0 is the LSB of the Instruction Register, and Bit 2 is the MSB. When the Instruction Register is selected, TDI serially shifts data into the MSB, and the LSB serially shifts data out through TDO. 18Mb 1x2Lp, HSTL, rev 1.1 19 / 25 November 8, 2002 SONY® ΣRAM Preliminary CXK79M36C162GB Bypass Register (DR - 1 bit) The Bypass Register is one bit wide, and provides the minimum length serial path between TDI and TDO. It is loaded with a logic “0” when the BYPASS instruction has been loaded in the Instruction Register and the TAP Controller is in the “Capture-DR” state. It is inserted between TDI and TDO when the BYPASS instruction has been loaded into the Instruction Register and the TAP Controller is in the “Shift-DR” state. ID Register (DR - 32 bits) The ID Register is loaded with a predetermined device- and manufacturer-specific identification code when the IDCODE instruction has been loaded into the Instruction Register and the TAP Controller is in the “Capture-DR” state. It is inserted between TDI and TDO when the IDCODE instruction has been loaded into the Instruction Register and the TAP Controller is in the “Shift-DR” state. The ID Register is 32 bits wide, and is encoded as follows: Device Revision Number (31:28) Part Number (27:12) Sony ID (11:1) Start Bit (0) 512Kb x 36 xxxx 0000 0000 0101 1011 0000 1110 001 1 Bit 0 is the LSB of the ID Register, and Bit 31 is the MSB. When the ID Register is selected, TDI serially shifts data into the MSB, and the LSB serially shifts data out through TDO. Boundary Scan Register (DR - 84 bits) The Boundary Scan Register is equal in length to the number of active signal connections to the SRAM (excluding the TAP pins) plus a number of place holder locations reserved for functional and/or density upgrades. It is loaded with the individual logic states of all signals composing the SRAM’s I/O ring when the EXTEST-A, SAMPLE, or SAMPLE-Z instruction has been loaded into the Instruction Register and the TAP Controller is in the “Capture-DR” state. It is inserted between TDI and TDO when the EXTEST-A, SAMPLE, or SAMPLE-Z instruction has been loaded into the Instruction Register and the TAP Controller is in the “Shift-DR” state. The Boundary Scan Register contains the following bits: 512Kb x 36 DQx 36 A, A1 18 CK, CK 2 CQ1, CQ2, CQ1, CQ2 4 E1, ADV, W 3 E2, E3, EP2, EP3 4 ZQ 1 Place Holder 16 Note: CK and CK are connected to a differential input receiver that generates a single-ended input clock to these devices. Therefore, in order to capture deterministic values for these signals in the Boundary Scan Register, they must be at opposite logic levels when sampled. Note: When an external resistor RQ is connected between the ZQ pin and VSS, the value of the ZQ signal captured in the Boundary Scan Register is non-deterministic. 18Mb 1x2Lp, HSTL, rev 1.1 20 / 25 November 8, 2002 SONY® ΣRAM Preliminary CXK79M36C162GB Boundary Scan Register Bit Order Assignments The tables below depict the order in which the bits are arranged in the Boundary Scan Register. Bit 1 is the LSB and bit 84 is the MSB. When the Boundary Scan Register is selected, TDI serially shifts data into the MSB, and the LSB serially shifts data out through TDO. 512Kb x 36 Bit Signal Pad Bit Signal Pad Bit Signal 1 Pad NC (1) 5C 36 E3 8A 71 MCH 6J 2 NC (1) 5U 37 A 7B 72 A 3V 3 NC (1) 7U 38 A 7A 73 A 4V MCL (1) 6D 39 W 6B 74 A 4U 5 MCL (1) 6K 40 ADV 6A 75 A 5V 6 MCL (1) 6P 41 E1 6C 76 A 6U 7 MCL (1) 6T 42 A 5A 77 A 5W MCH (2) 6N 43 A 5B 78 MCL 6W 4 8 9 MCH 6M 44 E2 4A 79 A1 6V 10 MCL 6L 45 A 3A 80 A 7V 11 DQ 10R 46 ZQ 6F 81 A 8V 12 DQ 11P 47 MCL 4C 82 A 7W 13 DQ 10P 48 MCL 3B 83 A 8U 14 DQ 11N 49 DQ 2E 84 A 9V 15 DQ 10N 50 DQ 1F 16 DQ 11M 51 DQ 2F 17 DQ 10M 52 DQ 1G 18 DQ 11L 53 DQ 2G 19 DQ 10L 54 DQ 1H 20 CQ1 11K 55 DQ 2H 21 CQ1 10K 56 DQ 1J 22 DQ 11E 57 DQ 2J 22 DQ 10D 58 CQ2 1K 24 DQ 11D 59 CK 3K 25 DQ 10C 60 CK 4K 26 DQ 11C 61 CQ2 2K 27 DQ 10B 62 DQ 1R 28 DQ 11B 63 DQ 2T 29 DQ 11A 64 DQ 1T 30 DQ 10A 65 DQ 2U 31 MCL 9C 66 DQ 1U 32 MCL 8B 67 DQ 2V 33 EP3 6H 68 DQ 1V 34 EP2 6G 69 DQ 1W 35 A 9A 70 DQ 2W Note 1: These NC and MCL pins are connected to VSS internally, regardless of pin connection externally. Note 2: This MCH pin is connected to VDD internally, regardless of pin connection externally. 18Mb 1x2Lp, HSTL, rev 1.1 21 / 25 November 8, 2002 SONY® ΣRAM Preliminary CXK79M36C162GB •Ordering Information VDD I/O Type Configuration Speed (Cycle Time / Data Access Time) CXK79M36C162GB-33 1.8V HSTL 512Kb x 36 3.3ns / 1.8ns CXK79M36C162GB-4 1.8V HSTL 512Kb x 36 4.0ns / 2.1ns CXK79M36C162GB-5 1.8V HSTL 512Kb x 36 5.0ns / 2.3ns Part Number Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits. 18Mb 1x2Lp, HSTL, rev 1.1 22 / 25 November 8, 2002 SONY® ΣRAM Preliminary CXK79M36C162GB •(11x19) 209 Pin BGA Package Dimensions 209PIN BGA (PLASTIC) 2.0 ± 0.3 14.0 0.30 S A 13.0 .0 C1 3- x4 C1 0.20 S W V U T R P N M L K J H G F E D C B A S .5 0.15 B 2.0 0.35 21.0 22.0 0.30 S B 7 1. C 4PIN 1 INDEX 2.0 A 1.0 X 1.0 0.5 ± 0.1 1 2 3 4 5 6 7 8 9 10 11 209 - φ 0.6 ± 0.1 0.10 M S AB S DETAIL X PACKAGE STRUCTURE PRELIMINARY SONY CODE BGA-209P-01 JEITA CODE P-BGA209-14X22-1.0 JEDEC CODE 18Mb 1x2Lp, HSTL, rev 1.1 PACKAGE MATERIAL EPOXY RESIN TERMINAL TREATMENT COPPER-CLAD LAMINATE TERMINAL MATERIAL SOLDER PACKAGE MASS 1.1g 23 / 25 November 8, 2002 SONY® ΣRAM CXK79M36C162GB Preliminary •Revision History Rev. # Rev. Date Description of Modifications rev 0.0 02/23/01 Initial Version. rev 0.1 07/06/01 1. Modified DC Electrical Characteristics section (p. 9). Added IDD-33 and IDD-44 Average Power Supply Operating Current specifications. 2. Added 209 Pin BGA Package Dimensions (p. 24). rev 0.2 02/22/02 1. Added BGA Package Thermal Characteristics (p. 8). 2. Modified AC Electrical Characteristics section (p. 11). Removed “-44” bin. Added “-5” bin. -4 tCHCL tKHKL ± 0.12 to tKHKL ± 0.1 tCLCH tKLKH ± 0.12 to tKLKH ± 0.1 3. Added JTAG ID Codes (p. 21). 4. Added JTAG Boundary Scan Register Bit Order Assignments (pp. 22-23). rev 1.0 07/19/02 1. Modified Pin Assignment section (p. 2-4). Pin 1K CQ to CQ2 Pin 2K CQ to CQ2 Pin 10K CQ to CQ1 Pin 11K CQ to CQ1 Pin 6J M4 to MCH Pin 6L M2 to MCL Pin 6M M3 to MCH 2. Modified I/O Capacitance section (p. 8). CKIN 3.5pF to 4.0pF 3. Modified DC Recommended Operating Conditions section (p. 9). Combined -1.8 and -1.5 line items into one for VDDQ, VREF, and VCM. VREF (min) 0.65V to VDDQ/2 - 0.1V VREF (max) 1.0V to VDDQ/2 + 0.1V VCM (min) 0.65V to VDDQ/2 - 0.1V VCM (max) 1.0V to VDDQ/2 + 0.1V Removed notes 1 and 2. 4. Modified DC Electrical Characteristics section (p. 10). Added MCH and MCL Input Leakage Current specifications. Reduced x36 Average Power Supply Operating Currents by 100mA. Reduced x18 Average Power Supply Operating Currents by 50mA. 5. Modified AC Electrical Characteristics section (p. 11). -33 tKHCH (max), tKLCL (max), tKHCZ 1.7ns to 1.8ns -4 tKHCH (max), tKLCL (max), tKHCZ 2.0ns to 2.1ns -5 tKHCH (max), tKLCL (max), tKHCZ 2.2ns to 2.3ns 6. Modified JTAG DC Recommended Operating Conditions section (p. 17). VTIH (min) 1.2V to VDD/2 + 0.3V VTIL (max) 0.6V to VDD/2 - 0.3V ITLI (min) -10uA to -20uA 7. Modified JTAG AC Electrical Characteristics section (p. 18). tTHTH 20ns to 50ns tTHTL, tTLTH 8ns to 20ns Added tCS Capture Setup and tCH Capture Hold specifications. 8. Modified TAP Registers section (p. 20). Instruction Register Codes 011, 110 Bypass to Private 9. Modified Boundary Scan Register Bit Order Assignments section (p. 22). x36 Bit 29 10A to 11A x36 Bit 30 11A to 10A 18Mb 1x2Lp, HSTL, rev 1.1 24 / 25 November 8, 2002 SONY® ΣRAM Rev. # rev 1.1 Rev. Date 11/08/02 18Mb 1x2Lp, HSTL, rev 1.1 CXK79M36C162GB Preliminary Description of Modifications 1. Removed x18 organization and all related references. 2. Modified Pin Description section (p. 3). For NC pins, removed reference to VDD and VDDQ. 3. Modified AC Electrical Characteristics section (p. 10). -33 tCHQV, tCLQV 0.2ns to 0.25ns tCHQX, tCLQX -0.2ns to -0.25ns Removed tCHCL and tCLCH Output Clock High and Low Pulse Width specifications. 4. Modified JTAG AC Electrical Characteristics section (p. 17). tCH 5ns to 8ns Added Note 1 for tCS and tCH specifications. 25 / 25 November 8, 2002