CXP82532/82540
CMOS 8-bit Single Chip Microcomputer
Description
The CXP82532/82540 microcomputer is composed
of a CPU, ROM RAM, and I/O ports. These chips
feature many other high-performance circuits in a
single-chip CMOS design, including an A/D
converter, serial interface, timer/counter, time-base
timer, capture timer/counter, fluorescent display
controller/driver, remote control receiver.
This device also includes a power-on reset function
and sleep/stop functions which can be used to
achieve low power consumption.
80 pin QFP (Plastic)
Features
• Instruction set which supports a wide array of data types
— 213 types of instructions which include 16-bit calculations, multiplication and division arithmetic, and
boolean bit operations.
• Minimum instruction cycle
400ns for 10MHz operation
• On-chip ROM
32K bytes (CXP82532)
40K bytes (CXP82540)
• On-chip RAM
1120 bytes (Including fluorescent display data area)
• Peripheral functions:
— A/D converter
8-bit, 8-channel, successive approximation system
(conversion time 32µs/10MHz)
— Serial interface
On-chip 8-bit, 8-stage FIFO (1 to 8 bytes auto transfer) 1 channel
8-bit clock synchronized 1 channel
— Timers
8-bit timer
8-bit timer/counter
19-bit time-base timer
16-bit capture timer/counter
— Fluorescent display controller/driver
Maximum of 336 segment display available
1 to 16 digits dynamic display
Dimmer function
High voltage tolerance output (40V)
On-chip pull-down resistor (Mask option)
— Remote control receiver circuit
On-chip noise elimination circuit
On-chip 6 stage FIFO 8-bit pulse measurement counter
• Interrupts
14 factors, 15 vectors multi-interruption possible
• Standby mode
Sleep/stop
• Package
80-pin plastic QFP
• Piggyback/evaluator
CXP82500 80-pin ceramic QFP
Structure
Silicon gate CMOS IC
Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by
any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the
operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.
–1–
E92Y32A78-PS
–2–
8
8
21
T0 to T7
T8/S28
T15/S21
S0 to S20
TO
CINT
EC1
EC0
SI1
SO1
SCK1
CS0
SI0
SO0
SCK0
RMC
VFDP
8
FIFO
FIFO
RAM
80 BYTES
16 BIT CAPTURE
TIMER/COUNTER 2
8 BIT TIMER 1
8 BIT TIMER/COUNTER 0
SERIAL INTERFACE UNIT 1
SERIAL
INTERFACE
UNIT 0
REMOCON
FDP
CONTROLLER/
DRIVER
A/D CONVERTER
2
INT0
INT1
INT2
INT3
2
PRESCALER/
TIME BASE TIMER
ROM
32/40K BYTES
SPC700
CPU CORE
EXTAL
XTAL
RST
VDD
VSS
RAM
1040 BYTES
CLOCK GEN./
SYSTEM CONTROL
PB0 to PB6
7
PE0 to PE5
PE6 to PE7
PF0 to PF7
6
2
8
4
PG0 to PG3
PD0 to PD7
8
PC0 to PC7
PB7
PA0 to PA7
8
8
PORT E
AN0 to AN7
PORT A
PORT B
PORT C
PORT D
PORT F
PORT G
INTERRUPT CONTROLLER
Block Diagram
CXP82532/82540
CXP82532/82540
T5
T4
T3
T2
T1
T0
VFDP
VDD
NC
PG0
PG1
PG2
PG3
PE0/EC0/INT0
PE1/EC1/INT1
PE2/IN2
Pin Assignment (Top View)
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65
PE3/INT3
1
64
T6
PE4/RMC
2
63
T7
PE5
3
62
T8/S28
PE6
4
61
T9/S27
PE7/TO
5
60
T10/S26
PB0/CINT
6
59
T11/S25
PB1/CS0
7
58
T12/S24
PB2/SCK0
8
57
T13/S23
PB3/SI0
9
56
T14/S22
PB4/SO0
10
55
T15/S21
PB5/SCK1
11
54
S20
PB6/SI1
12
53
S19
PB7/SO1
13
52
S18
PC0/KR0
14
51
S17
PC1/KR1
15
50
S16
PC2/KR2
16
49
PF7/S15
PC3/KR3
17
48
PF6/S14
PC4/KR4
18
47
PF5/S13
PC5/KR5
19
46
PF4/S12
PC6/KR6
20
45
PF3/S11
PC7/KR7
21
44
PF2/S10
PA0/AN0
22
43
PF1/S9
PA1/AN1
23
42
PF0/S8
PA2/AN2
24
41
PD7/S7
Note) NC (Pin 73) is always connected to VDD.
–3–
PD6/S6
PD4/S4
PD5/S5
PD3/S3
PD2/S2
PD1/S1
PD0/S0
VSS
XTAL
EXTAL
RST
PA7/AN7
PA6/AN6
PA5/AN5
PA4/AN4
PA3/AN3
25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
CXP82532/82540
Pin Description
Symbol
I/O
Description
(Port A)
8-bit port; single bit
addressable.
(8 pins)
PA0/AN0
to
PA7/AN7
I/O/Analog input
PB0/CINT
I/O/Input
External capture input for 16-bit timer/counter.
PB1/CS0
I/O/Input
Chip select input for serial interface (CH0).
PB2/SCK0
I/O/I/O
PB3/SI0
I/O/Input
PB4/SO0
I/O/Output
PB5/SCK1
I/O/I/O
PB6/SI1
I/O/Input
Serial data (CH1) input.
PB7/SO1
Output/Output
Serial data (CH1) output.
PC0/KR0
to
PC7/KR7
I/O/Input
(Port B)
Single bit addressable from
amongst lower 7 bits;
highest bit (PB7)
dedicated to output.
(8 pins)
(Port C)
8-bit port; single bit
addressable. Can provide
12mA sink current.
(8 pins)
Analog input to A/D converter.
(8 pins)
Serial clock (CH0) input/output.
Serial data (CH0) input.
Serial data (CH0) output.
Serial clock (CH1) input/output.
Key return input for FDP segment signal
which performs key scanning.
PE0/INT0/EC0 Input/Input/Input
PE1/INT1/EC1 Input/Input/Input
Input for external
interrupt requests.
(4 pins)
External event input
to timer/counter.
(2 pins)
PE2/INT2
Input/Input
PE3/INT3
Input/Input
PE4/RMC
Input/Input
PE5
Input
PE6
Output
PE7/TO
Output/Output
PG0 to PG3
I/O
(Port G)
4-bit input/output port; single bit addressable.
(4 pins)
PF0/S8
to
PF7/S15
Output/Output
(Port F)
8-bit dedicated output port.
(8 pins)
S16 to S20
Output
Segment signal output for FDP.
T8/S28
to
T15/S21
Output/Output
Dual purpose output for FDP timing and segment signals.
T0 to T7
Output
Timing signal output for FDP.
PD0/S0
to
PD7/S7
Output/Output
(Port D)
8-bit dedicated output port. Segment signal output for FDP.
(8 pins)
(Port E)
8-bit port with lower 6 bits
dedicated to input and
upper 2 bits dedicated to
output.
(8 pins)
Input for remote control receiver circuit.
Output pin for 16-bit timer/counter
rectangular waveform.
–4–
Segment signal
output for FDP.
CXP82532/82540
Symbol
I/O
Description
Provides voltage for FDP when on-chip resistor is selected under mask
option.
VFDP
EXTAL
Input
XTAL
Output
RST
I/O
Connection for system clock oscillation crystal. When using an external
clock, input normal signal to EXTAL and reverse phase signal to the
XTAL pin.
System reset, active "L". The RST pin is an input/output pin which
outputs a "L" level from the on-chip power-on reset circuit when the
power is turned on. (Mask option)
NC
NC pin is always connected to VDD.
VDD
Positive power supply pin.
VSS
GND
–5–
CXP82532/82540
Input/Output Circuit Formats for Pins
When reset
Circuit format
Pin
Port A
Port A data
PA0/AN0
to
PA7/AN7
Port A direction
Input
protection
circuit
IP
"0" when reset
Hi-Z
Data bus
RD (Port A)
Port A input select
"0" when reset
Input multiplexer
A/D converter
8 pins
Port B
Port B data
PB0/CINT
PB1/CS0
PB3/SI0
PB6/SI1
Port B direction
IP
"0" when reset
Hi-Z
Schmitt input
Data bus
RD (Port B)
CINT
CS0
SI0
SI1
4 pins
Port B
SCK OUT
Output enable
Port B output select
"0" when reset
Port B data
PB2/SCK0
PB5/SCK1
IP
Hi-Z
Port B direction
"0" when reset
Data bus
Schmitt input
RD (Port B)
2 pins
SCK in
–6–
CXP82532/82540
Circuit format
Pin
When reset
Port B
SO
Output enable
Port B output select
"0" when reset
Port B data
PB4/SO0
IP
Hi-Z
Port B direction
"0" when reset
Data bus
RD (Port B)
1 pin
Port B
Internal reset signal
SO
Output enable
∗
Port B output select
PB7/SO1
"0" when reset
High level
Port B data
"1" when reset
Data bus
∗Pull-up transistor
about 200kΩ
RD (Port B)
1 pin
Port C
Port C data
PC0/KR0
to
PC7/KR7
∗
Port C direction
IP
"0" when reset
Hi-Z
Data bus
RD (Port C)
Key input signal
∗Capable of driving 12mA large current
8 pins
Port E
PE0/EC0/INT0
PE1/EC1/INT1
PE2/INT2
PE3/INT3
PE4/RMC
5 pins
EC0/INT0
EC1/INT1
INT2
INT3
RMC
Schmitt input
IP
Data bus
RD (Port E)
–7–
Hi-Z
CXP82532/82540
Circuit format
Pin
When reset
Port E
PE5
IP
Data bus
Hi-Z
RD (Port E)
1 pin
Port E
PE6
High level
Port E data
"1" when reset
1 pin
Port E
TO
Output enable (T2OE)
Port E output select
PE7/TO
"0" when reset
High level
Port E data
"1" when reset
Data bus
1 pin
RD (Port E)
Port G
Port G data
PG0
to
PG3
Port G direction
IP
"0" when reset
Data bus
RD (Port G)
4 pins
–8–
Hi-Z
CXP82532/82540
Pin
Circuit format
When reset
Port D
PD0/S0
to
PD7/S7
∗High voltage tolerance transistor
Port F
Segment output data
∗
Output selection control signal
("0" when reset)
Port D data or
Port F data
PF0/S8
to
PF7/S15
OP
"0" when reset
Mask option
Pull-down
resistor
Data bus
Hi-Z or
Low level
(when PD
resistor is
connected)
VFDP
16 pins
RD (Port D or Port F)
∗High voltage tolerance transistor
S16 to S20
T15/S21
to
T8/S28
T0 to T7
Segment output data
∗
Output selection control signal
("0" when reset)
Mask option
OP
Pull-down
resistor
Hi-Z or
Low level
(when PD
resistor is
connected)
VFDP
21 pins
∗Diagram shows
EXTAL
XTAL
circuit construction
for oscillation.
EXTAL
IP
IP
∗During stop
Oscillation
feedback resistor is
disconnected.
XTAL
2 pins
Pull-up resistor
RST
OP Mask option
IP
1 pin
Low level
Schmitt input
From power-on reset circuit
(Mask option)
–9–
CXP82532/82540
Absolute Maximum Ratings
Item
(Vss = 0V)
Symbol
Rating
Unit
V
Remarks
Supply voltage
VDD
Input voltage
VIN
–0.3 to +7.0
–0.3 to +7.0∗1
Output voltage
VOUT
–0.3 to +7.0∗1
V
Display output voltage
VOD
VDD – 40 to
VDD + 0.3
V
IOH
–5
mA
As P channel transistor is open drain,
VDD voltage is determined as standerd.
Other than display output pins∗2 : per pin
IODH1
–15
mA
Display outputs S0 to S20: per pin
IODH2
–35
mA
Display outputs T0 to T7,
T8/S28 to T15/S21: per pin
∑IOH
–40
mA
Total of other than display output pins
∑IODH
–100
mA
Total of display output pins
IOL
15
mA
Port 1 pin
IOLC
20
mA
Large current port pin ∗3
Low level total output current
∑IOL
100
mA
Entire pin total
Operating temperature
Topr
–20 to +75
°C
Storage temperature
Tstg
–55 to +150
°C
Allowable power dissipation
PD
600
mW
High level output current
High level total output current
Low level output current
V
∗1 VIN and VOUT cannot exceed VDD + 0.3V.
∗2 Rating for output current of general input/output port.
∗3 The large current drive transistor is an N-channel transistor of Port C.
Note) If the absolute maximum ratings are exceeded, the LSI could reach permanent breakdown. Also,
observing recommended operating conditions is desirable; otherwise, the LSI's reliability could be
affected.
– 10 –
CXP82532/82540
Recommended Operating Conditions
Item
Supply voltage
High level input
voltage
Symbol
(Vss = 0V)
Min.
Max.
4.5
5.5
3.5
5.5
2.5
5.5
VIH
0.7VDD
VDD
V
VIHS
0.8VDD
VDD
V
VDD
VIHEX VDD – 0.4 VDD + 0.3
Unit
High-speed mode (1/2, 1/4 clock) guaranteed
range during operation
V
Low-speed mode (1/16 clock) guaranteed range
during operation
Guaranteed data hold range during stop
∗1
V
Hysteresis input∗2
EXTAL pin∗3
∗1
VIL
0
0.3VDD
V
VILS
0
0.2VDD
V
VILEX
–0.3
0.4
V
Operating temperature Topr
–20
+75
°C
Low level input
voltage
Remarks
Hysteresis input
EXTAL pin∗3
∗1 All regular input ports (PA, PB3, PB4, PB6, PC, PE5, PG).
∗2 For pins RST, CINT, CS0, SCK0, SCK1, EC0/INT0, EC1/INT1 , INT2, INT3, RMC.
∗3 Rating only for external clock input.
– 11 –
CXP82532/82540
Electrical Characteristics
DC Characteristics
Item
High level
output voltage
Low level
output voltage
(Ta = –20 to +75°C, Vss = 0V)
Symbol
VOH
Pins
PA, PB, PC,PE6,
PE7, PG, RST∗1
(for VOL only)
VOL
PC
IIHE
Input current
IILE
IILR
EXTAL
RST∗2
Conditions
VDD = 4.5V, IOH = –0.5mA
4.0
V
VDD = 4.5V, IOH = –1.2mA
3.5
V
VDD = 4.5V, IOL = 1.8mA
0.4
V
VDD = 4.5V, IOL = 3.6mA
0.6
V
VDD = 4.5V, IOL = 12.0mA
1.5
V
µA
VDD = 5.5V, VIH = 5.5V
0.5
40
VDD = 5.5V, VIL = 0.4V
–0.5
–40 µA
VDD = 5.5V, VIL = 0.4V
–1.5
–400 µA
S0 to S20
VDD = 4.5V
VOH = VDD – 2.5V
Display output
current
IOH
Open drain output
leak current
(P-CH Tr off state)
ILOL
S0 to S20
S21/T15 to S28/T8
T0 to T7
VDD = 5.5V
VOL = VDD – 35V
VFDP = VDD – 35V
Pull-down
resistor∗3
RL
S0 to S20
S21/T15 to S28/T8
T0 to T7
VDD = 5V
VOD – VFDP = 30V
Input/output leak
current
IIZ
PA to PC, PE, PG,
RST∗2
VDD = 5.5V
VI = 0, 5.5V
S21/T15 to S28/T8
T0 to T7
Min. Typ. Max. Unit
–8
mA
–20
mA
–20 µA
60
100 270 kΩ
±10 µA
VDD = 5.5V
High-speed mode
(1/2 clock) operation
IDD1
Supply current∗4
Input capacitance
VDD
10MHz crystal
oscillator
(C1 = C2 = 15pF)
IDDSL
Sleep mode
IDDST
Stop mode
CIN
For pins other
than S0 to S28,
T0 to T7, PB7,
PE6, PE7, VDD,
VSS, VFDP
1MHz clock
0V other than measured
25
40 mA
3
8
mA
10
µA
20
pF
10
∗1 RST pin is rated only when the power-on circuit is selected under the mask option.
∗2 RST pin is rated for input current when the pull-up resistor is selected; otherwise it is rated for leak current.
∗3 Applies when the on-chip pull-down resistor is selected under the mask option.
∗4 All output pins are left open.
– 12 –
CXP82532/82540
AC Characteristics
(1) Clock timing
(Ta = –20 to +75°C, VDD = 4.5 to 5.5V, Vss = 0V)
Item
Symbol
Pins
Conditions
Min.
Max.
Unit
10
MHz
System clock frequency
fC
XTAL
Fig. 1, Fig. 2
EXTAL
1
System clock input pulse width
tXL,
tXH
Fig. 1, Fig. 2
EXTAL External clock driver
45
tCR,
tCF
tEH,
tEL
tER,
tEF
Fig. 1, Fig. 2
EXTAL External clock driver
System clock input rising and
falling times
Event count input clock pulse
width
Event count input clock rising
and falling times
∗1
EC0,
EC1
Fig. 3
EC0,
EC1
Fig. 3
ns
200
tsys + 50∗1
ns
ns
20
ms
tsys is determind by the upper two bits of the clock control resister (Address: 00FEH; CPU clock selected)
resulting in one of the 3 following values:
tsys [ns] = 2000/fc (Upper 2 bits = "00"), 4000/fc (Upper 2 bits = "01"), 16000/fc (Upper 2 bits = "11")
Fig. 1. Clock timing
1/fc
VDD – 0.4V
EXTAL
0.4V
tXH
tCF
tXL
tCR
Fig. 2. Clock applying condition
AAAA
AAAA
AAAA
AAAA
AAAA AAAA
Crystal oscillation
Ceramic oscillation
EXTAL
C1
External clock
EXTAL
XTAL
C2
XTAL
74HC04
Fig. 3. Event count clock timing
0.8VDD
EC0
EC1
0.2VDD
tEH
tEF
tEL
tER
tTH
tTF
tTL
tTR
– 13 –
CXP82532/82540
(2) Serial transfer (CH0)
Item
(Ta = –20 to +75°C, VDD = 4.5 to 5.5V, Vss = 0V)
Symbol
Pin
Condition
Min.
Max.
Unit
CS0 ↓ → SCK0
delay time
tDCSK
SCK0
Chip select transfer mode
(SCK0 = output mode)
tsys + 200
ns
CS0 ↑ → SCK0
float delay time
tDCSKF SCK0
Chip select transfer mode
(SCK0 = output mode)
tsys + 200
ns
CS0 ↓ → SO0
delay time
tDCSO
SO0
Chip select transfer mode
tsys + 200
ns
CS0 ↑ → SO0
float delay time
tDCSOF SO0
Chip select transfer mode
tsys + 200
ns
CS0 high level width
tWHCS CS0
Chip select transfer mode
SCK0 cycle time
tKCY
SCK0
SCK0
high and low level width
tKH
tKL
SCK0
SI0 input setup time
(against SCK0 ↑)
tSIK
SI0
SI0 input hold time
(against SCK0 ↑)
tKSI
SI0
SCK0 ↓ → SO0
delay time
tKSO
SO0
tsys + 200
2tsys + 200
ns
16000/fc
ns
Input mode
tsys + 100
ns
Output mode
8000/fc – 50
ns
SCK0 input mode
100
ns
SCK0 output mode
200
ns
tsys + 200
ns
100
ns
Input mode
Output mode
SCK0 input mode
SCK0 output mode
SCK0 input mode
SCK0 output mode
ns
tsys + 200
ns
100
ns
tsys is determind by the upper two bits of the clock control resister (Address: 00FEH; CPU clock
selected) resulting in one of the 3 following values:
tsys [ns] = 2000/fc (Upper 2 bits = "00"), 4000/fc (Upper 2 bits = "01"), 16000/fc (Upper 2 bits = "11")
Note 2) The load of SCK0 output mode and SO0 output delay time is 50pF + 1TTL.
Note 1)
– 14 –
CXP82532/82540
Fig. 4. Serial transfer CH0 timing
tWHCS
CS0
0.8VDD
0.2VDD
tKCY
tDCSK
tKL
tDCSKF
tKH
0.8VDD
0.8VDD
SCK0
0.2VDD
tSIK
tKSI
0.8VDD
Input
data
SI0
0.2VDD
tDCSO
tKSO
tDCSOF
0.8VDD
SO0
Output data
0.2VDD
– 15 –
CXP82532/82540
Serial transfer (CH1)
Item
SCK1 cycle time
(Ta = –20 to +75°C, VDD = 4.5 to 5.5V, Vss = 0V)
Symbol
tKCY
Pin
Condition
Min.
Input mode
SCK1
tKH
tKL
SCK1
SI1 input setup time
(against SCK1 ↑)
tSIK
SI1
SI1 input hold time
(against SCK1 ↑)
tKSI
ns
16000/fc
ns
400
ns
8000/fc – 50
ns
SCK1 input mode
100
ns
SCK1 output mode
200
ns
SCK1 input mode
200
ns
SCK1 output mode
100
ns
SCK1 ↓ → SO1 delay time
tKSO
Input mode
Output mode
SI1
SO1
SCK1 input mode
200
ns
SCK1 output mode
100
ns
Note) The load of SCK1 output mode and SO1 output delay time is 50pF + 1TTL.
Fig. 5. Serial transfer CH1 timing
tKCY
tKL
tKH
SCK1
0.8VDD
0.2VDD
tSIK
tKSI
0.8VDD
SI1
Unit
1000
Output mode
SCK1 high and low
level width
Max.
Input data
0.2VDD
tKSO
0.8VDD
Output data
SO1
0.2VDD
– 16 –
CXP82532/82540
(3) A/D converter characteristics
Item
Symbol
(Ta = –20 to +75°C, VDD = 4.5 to 5.5V, Vss = 0V)
Pin
Condition
Min.
Typ.
Resolution
Linearity error
Zero transition voltage
VZT∗1
Full-scale transition
voltage
VFT∗2
Conversion time
Sampling time
tCONV
tSAMP
Analog input voltage
VIAN
A/D converter operation
only
Ta = 25°C
VDD = 5.0V
VSS = 0V
Max.
Unit
8
Bits
±3
LSB
–10
70
150
mV
4930
5050
5120
mV
160/fADC ∗3
12/fADC ∗3
AN0 to AN7
0
µs
µs
VDD
V
Fig. 6. Definition of A/D converter terms
FFH
FEH
Digital conversion value
∗1 VZT : Digital Value converted between 00H to 01H.
∗2 VFT : Digital Value converted between FEH and FFH.
∗3 fADC : ADC operation clock selection (MSC: Bit 0 of
address 01FFH) and assumes following values:
fADC = fc/2 when PS2 is selected.
fADC = fc when PS1 is selected.
Linearity error
01H
00H
VZT
VFT
Analog input
– 17 –
CXP82532/82540
(4) Interrupts, reset inputs
(Ta = –20 to +75°C, VDD = 4.5 to 5.5V, Vss = 0V)
Item
Symbol
Pin
Condition
Min.
Max.
Unit
External interrupt High and
Low level widths
tIH
tIL
INT0
INT1
INT2
INT3
1
µs
Reset input Low level width
tRSL
RST
8/fc
µs
Fig. 7. Interrupt input timing
tIH
tIL
0.8VDD
0.2VDD
INT0
INT1
INT2
INT3
tIL
tIH
0.8VDD
0.2VDD
Fig. 8. RST input timing
tRSL
RST
0.2VDD
(5) Power-on reset
Power-on reset∗
(Ta = –20 to +75°C, VDD = 4.5 to 5.5V, VSS = 0V)
Item
Symbol
tR
Power supply cut-off time tOFF
Pin
Condition
Power-on reset
Power supply rising time
VDD
Repetitive power-on reset
∗ Specifies only when power-on reset function is selected.
Min.
Max.
Unit
0.05
50
ms
1
Fig. 9. Power-on reset
4.5V
VDD
0.2V
0.2V
tR
tOFF
The power supply should be rise smoothly.
– 18 –
ms
CXP82532/82540
Supplement
Fig. 10. Recommended Oscillation Circuit
AAAAA
AAAAA
AAAAA
AAAAA
AAAAA AAAAA
(i)
(ii)
EXTAL
C1
EXTAL
XTAL
C2
C1
Manufacturer
MURATA MFG
CO., LTD
XTAL
Model
fc (MHz)
CSA4.19MG
4.19
CSA8.00MG
8.00
CSA10.0MT
10.00
CST4.19MGW∗
CST8.00MTW∗
CST10.00MTW∗
4.19
C2
C1 (pF)
C2 (pF)
Circuit
Example
(i)
30
30
(ii)
8.00
10.00
4.19
FUJI SANGYO
CO., LTD
HC-49/U03
8.00
15
15
10.00
(i)
4.19
KINSEKI LTD.
HC-49/U (-S)
8.00
27
10.00
∗ Indicates types with on-chip grounding capacitors (C1 and C2).
– 19 –
27
CXP82532/82540
Package Outline
Unit: mm
80PIN QFP (PLASTIC)
23.9 ± 0.4
+ 0.1
0.15 – 0.05
+ 0.4
20.0 – 0.1
64
0.15
41
65
16.3
17.9 ± 0.4
+ 0.4
14.0 – 0.1
40
A
+ 0.2
0.1 – 0.05
25
1
24
0.8
0.12
M
+ 0.15
0.35 – 0.1
+ 0.35
2.75 – 0.15
0° to 10°
DETAIL A
PACKAGE STRUCTURE
PACKAGE MATERIAL
EPOXY RESIN
SOLDER PLATING
SONY CODE
QFP-80P-L01
LEAD TREATMENT
EIAJ CODE
QFP080-P-1420
LEAD MATERIAL
42/COPPER ALLOY
PACKAGE MASS
1.6g
JEDEC CODE
– 20 –
0.8 ± 0.2
80