Product Description Stanford Microdevices SGA-4363 is a high performance SiGe Heterojunction Bipolar Transistor MMIC Amplifier. A Darlington configuration featuring 1 micron emitters provides high FT and excellent thermal perfomance. The heterojunction increases breakdown voltage and minimizes leakage current between junctions. Cancellation of emitter junction non-linearities results in higher suppression of intermodulation products. At 850 Mhz and 45mA , the SGA-4363 typically provides +28.7 dBm output IP3, 16.4 dB of gain, and +14.3 dBm of 1dB compressed power using a single positive voltage supply. Only 2 DC-blocking capacitors, a bias resistor and an optional RF choke are required for operation. VD= 3.2 V, ID= 45 mA (Typ.) Cascadable 50 Ohm Patented SiGe Technology -10 Operates From Single Supply Low Thermal Resistance Package -20 6 -30 0 Return Loss (dB) Gain (dB) IRL 12 -40 0 1 2 3 4 Frequency (GHz) Sy mbol 5 Product Features 0 ORL 18 GAIN DC-2000 MHz, Cascadable SiGe HBT MMIC Amplifier High Gain : 14.8 dB at 1950 MHz Gain & Return Loss vs. Frequency 24 SGA-4363 6 Cellular, PCS, CDPD Wireless Data, SONET Satellite Units Frequency Min. Ty p. Max. dB dB 850 M Hz 1950 M Hz 14.8 16.4 14.8 18.0 Output Pow er at 1dB Compression dBm dBm 850 M Hz 1950 M Hz 14.3 13.0 Output Third Order Intercept Point (Pow er out per tone = -5dBm) dBm dBm 850 M Hz 1950 M Hz 28.7 25.7 Bandw idth Determined by Return Loss (<-10dB) M Hz G P1dB OIP3 IRL Parameter Applications Small Signal Gain 2000 Input Return Loss dB 1950 M Hz 14.4 Output Return Loss dB 1950 M Hz 10.7 NF Noise Figure dB 1950 M Hz 3.1 VD Device Voltage V RTh Thermal Resistance ORL Test Conditions: VS = 8 V RBIAS = 110 Ohms °C/W ID = 45 mA Typ. TL = 25ºC 2.9 3.2 3.5 255 OIP3 Tone Spacing = 1 MHz, Pout per tone = -5 dBm ZS = ZL = 50 Ohms The information provided herein is believed to be reliable at press time. Stanford Microdevices assumes no responsibility for inaccuracies or omissions. Stanford Microdevices assumes no responsibility for the use of this information, and all such information shall be entirely at the users own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. Stanford Microdevices does not authorize or warrant any Stanford Microdevices product for use in life-support devices and/or systems. Copyright 2000 Stanford Microdevices, Inc. All worldwide rights reserved. 726 Palomar Ave., Sunnyvale, CA 94085 Phone: (800) SMI-MMIC 1 http://www.stanfordmicro.com EDS-100642 Rev. B Preliminary SGA-4363 DC-2000 MHz Cascadable MMIC Amplifier Typical RF Performance at Key Operating Frequencies Sy mbol G Parameter Unit 100 500 dB 17.0 Small Signal Gain Frequency (MHz) Frequency Frequency (MHz)(MHz) 850 1950 16.7 16.4 14.8 29.4 28.7 25.7 OIP3 Output Third Order Intercept Point dBm P1dB Output Pow er at 1dB Compression dBm 14.3 14.3 13.0 IRL Input Return Loss dB 11.9 12.2 12.9 14.4 ORL Output Return Loss dB 10.2 11.5 13.3 10.7 S12 Reverse Isolation dB 20.9 21.4 21.4 20.7 NF Noise Figure dB 2.8 2.7 3.1 VSS== 88 V V V RBIAS = 110 Ohms R BIAS= 39 Ohms Test Conditions: 45 mA mA Typ. Typ. IIDD == 80 25ºC TTLL == 25ºC Absolute Maximum Ratings VD= 3.2 V, ID= 45 mA (Typ.) Noise Figure (dB) 5 1 1 1.5 2 Frequency (GHz) 2.5 90 mA 5V +8 dBm Max. Junction Temp. (TJ) +150°C Operating Temp. Range (TL) -40°C to +85°C Max. Storage Temp. +150°C Operation of this device beyond any one of these limits may cause permanent damage. TL=+25ºC 0 0.5 Absolute Limit Max. RF Input Pow er TL=+25ºC 2 Parameter Max. Device Current (ID) Max. Device Voltage (VD) 4 0 Bias Conditions should also satisfy the following expression: IDVD (max) < (TJ - TL)/Rth 3 OIP3 vs. Frequency P1dB vs. Frequency VD=3.2 V, ID= 45 mA (Typ.) 18 VD= 3.2 V, ID= 45 mA (Typ.) 35 15 30 OIP3 (dBm) P1dB (dBm) 3500 OIP33 Tone Tone Spacing Spacing == 11 MHz, MHz, Pout Pout per per tone tone == 0-5dBm dBm OIP 50 Ohms Ohms ZZSS== ZZLL== 50 Noise Figure vs. Frequency 3 2400 12 25 20 9 TL=+25ºC TL=+25ºC 15 6 0 0.5 1 1.5 2 Frequency (GHz) 726 Palomar Ave., Sunnyvale, CA 94085 2.5 3 Phone: (800) SMI-MMIC 2 0 0.5 1 1.5 2 Frequency (GHz) 2.5 3 http://www.stanfordmicro.com EDS-100642 Rev. B Preliminary SGA-4363 DC-2000 MHz Cascadable MMIC Amplifier |S | vs. Frequency |S | vs. Frequency VD= 3.2 V, ID= 45 mA (Typ.) VD= 3.2 V, ID= 45 mA (Typ.) 21 20 11 0 -10 S11(dB) S21(dB) 15 10 5 0 0 1 2 3 4 Frequency (GHz) -30 +25°C -40°C +85°C TL 5 -20 -40 6 0 1 5 |S | vs. Frequency VD= 3.2 V, ID= 45 mA (Typ.) VD= 3.2 V, ID= 45 mA (Typ.) 6 22 0 -10 S22(dB) -15 S12(dB) 2 3 4 Frequency (GHz) |S | vs. Frequency 12 -10 +25°C -40°C +85°C TL -20 -25 -30 0 1 2 3 4 Frequency (GHz) -30 +25°C -40°C +85°C TL 5 -20 +25°C -40°C +85°C TL -40 6 0 1 2 3 4 Frequency (GHz) 5 6 NOTE: Full S-parameter data available at www.stanfordmicro.com 726 Palomar Ave., Sunnyvale, CA 94085 Phone: (800) SMI-MMIC 3 http://www.stanfordmicro.com EDS-100642 Rev. B Preliminary SGA-4363 DC-2000 MHz Cascadable MMIC Amplifier Basic Application Circuit Application Circuit Element Values R BIAS VS 1 uF 1000 pF 500 850 1950 2400 3500 CB 220 pF 100 pF 68 pF 56 pF 39 pF CD 100 pF 68 pF 22 pF 22 pF 15 pF LC 68 nH 33 nH 22 nH 18 nH 15 nH CD LC 3 RF in CB 1,2 SGA-4363 6 R ecommended B ias R esistor Values for ID=45mA RF out CB 4,5 Frequency (Mhz) Reference Designator S upply Voltage(V S) RBIAS 6V 62 8V 110 10 V 150 12 V 200 Note: RBIAS provi des D C bi as stabi li ty over temperature. VS RBIAS LC A43 CB 1 uF 1000 pF CD Mounting Instructions 1. Use a large ground pad area near device pins 1, 2, 4, and 5 with many plated through-holes as shown. CB 2. We recommend 1 or 2 ounce copper. Measurements for this data sheet were made on a 31 mil thick FR-4 board with 1 ounce copper on both sides. Pin # Function 3 RF IN RF input pin. This pin requires the use of an external DC blocking capacitor chosen for the frequency of operation. 6 5 4 1 GND A43 Connection to ground. Use via holes for best performance to reduce lead inductance as close to ground leads as possible. 6 Part Identification Marking The part will be marked with an A43 designator on the top surface of the package. RF OUT/ RF output and bias pin. DC voltage is BIAS present on this pin, therefore a DC blocking capacitor is necessary for proper operation. 1 2 3 For package dimensions, refer to outline drawing at www.stanfordmicro.com Caution: ESD sensitive 2,4,5 GND Sames as Pin 2 Part Number Ordering Information Appropriate precautions in handling, packaging and testing devices must be observed. 726 Palomar Ave., Sunnyvale, CA 94085 Description Part Number Reel Size Devices/Reel SGA-4363 7" 3000 Phone: (800) SMI-MMIC 4 http://www.stanfordmicro.com EDS-100642 Rev. B