DC/DC Converter THP 3 Series 3 Watt High Isolation Features I/O-Isolation Voltage of 4000VAC Clearance and Creeping Distances min. 2.0mm Basic-, Supplementary- and Reinforced Insulation for Working Voltages up to 420VDC / 300VAC Ultra wide 4:1 Input Ranges: 9-40VDC,18-80VDC and 36-160VDC Extended Operating Temp. Range –40°C to 85°C Input Filter meets EN55022A without ext. Components Continuous Short Circuit Protection High Reliability, MTBF>1 Mio. Hours 3 Year Product Warranty The THP-3 series is a new range of high performance 3W DC/DC converters in a low profile DIL-24 package with standard industry pin-out. The very high I/O-isolation system of these converters and input voltages up to 160 VDC make this product the best choice for many demanding applications in railroad and transportation systems, medical equipment, instrumentation, everywhere where high basic-, supplementary- or reinforced insulation is requested to meet specific safety standards. A high efficiency allows safe operation in a temperature range of –40°C to +85°C at full load without derating. Full SMD-design with exclusive use of ceramic capacitors ensure a very high reliability and a long product lifetime. Models Ordercode THP 3-2411 THP 3-2412 THP 3-2422 THP 3-2423 THP 3-4811 THP 3-4812 THP 3-4822 THP 3-4823 THP 3-7211 THP 3-7212 THP 3-7222 THP 3-7223 www.tracopower.com Input voltage Output voltage Output current max. Efficiency typ. 9 – 40 VDC 5 12 ±12 ±15 VDC VDC VDC VDC 600 mA 250 mA ± 125 mA ± 100 mA 78 83 83 83 % % % % 18 – 80 VDC 5 12 ±12 ±15 VDC VDC VDC VDC 600 mA 250 mA ± 125 mA ± 100 mA 78 83 83 83 % % % % 36 – 160 VDC 5 12 ±12 ±15 VDC VDC VDC VDC 600 mA 250 mA ± 125 mA ± 100 mA 78 83 83 83 % % % % Page 1 DC/DC Converter THP 3 Series 3 Watt Input Specifications Input current at no load / full load 24 Vin models: 48 Vin models: 72 Vin models: 20 mA typ. / 160 mA typ. 10 mA typ. / 80 mA typ. 5 mA typ. / 35 mA typ. Start-up voltage / under voltage shut down 24 Vin models: 48 Vin models: 72 Vin models: 8.5 VDC / 8.5 VDC (typ.) 15 VDC / 16 VDC (typ.) 30 VDC / 32 VDC (typ.) Recommanded input fuse (slow blow) 24 Vin models: 48 Vin models: 72 Vin models: 1.0 A 0.5 A 0.3 A Surge voltage (1 sec. max.) 24 Vin models: 48 Vin models: 72 Vin models: 50 V max. 100 V max. 180 V max. Input filter EN 55022, level A (without external components) Output Specifications Voltage set accuracy ±1% Voltage balance (dual output models) ± 2 % max. Regulation ± 0.5 % max. ± 1.0 % max. – Input variation Vin min. to Vin max. – Load variation 25 – 100 %: Ripple and noise (20 MHz Bandwidth) 100 mVpk-pk typ. Temperature coefficient ± 0.02 % / °C typ. Current limitation > 120 % Iout max. Short circuit protection indefinite (automatic recovery) Capacitive load – 5 VDC output models: – 12 VDC output models: – Dual output models: 1000 µF max. 470 µF max. 220 µF max. (each output) Isolation /Safety Isolation test voltage (1 sec.) 5700 VDC I/O isolation voltage (50Hz, 60sec) 4000 VAC I/O clearance and creepage 2.0mm min. Leakage current 2 µA (at 240VAC, 60Hz) Isolation capacity input/output 7 pF typ. (at 100KHz, 1V) Isolation resistance input/output >1000 Mohm (at 500VDC) Safety standards IEC/EN 60950, UL 60950-1 CSA C22.2 No. 60950-1-03 IEC/EN 60601-1, EN 50124-1&2 UL 60601-1, CSA C22.2 No. 601-1 Safety approvals CB-report, CSA File No. 226037 All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated. www.tracopower.com Page 2 DC/DC Converter THP 3 Series 3 Watt General Specifications Temperature ranges – 40 °C ... +85 °C + 95 °C max. – 40 °C ... +125 °C – Operating – Case – Storage Derating 4 % /°K above 75°C Humidity (non condensing) 95 % rel H max. Reliability, calculated MTBF (MIL-HDBK-217 F) >1 Mio. h @ 25 °C, ground benign Switching frequency 150 kHz typ. (puls width modulation) Case material non conductive plastic (UL 94V-0-rated) Potting material Silicon TSE 3331 (UL 94V-0-rated) Weight 16.2 g (0.57 oz) Soldering temperature max. 260°C / 10 sec (0.1) 2.54 2. 0 (0.08) Outline Dimensions Pin-Out 1 Bottom view 20.32 (0.8) 15 (0.1) 2.54 (1.1) 27.9 4 32 (1.25) 24 23 11 12 (0.1) 2.54 13 4 10 (0.16) (0.4) 2.4 15 .24 (0.1) (0.6) Pin Single Dual 1 +Vin (Vcc) +Vin (Vcc) 11 No pin Common 12 –Vout No pin 13 +Vout –Vout 15 No pin +Vout 23 –Vin (GND) –Vin (GND) 24 –Vin (GND) –Vin (GND) 20 (0.79) Dimensions in mm, ( ) = inches Pin diameter: 0.6 mm ± 0.05 (0.024 ± 0.002) Tolerances: ±0.25mm (± 0.01) Specifications can be changed without notice Rev. 10/04 Jenatschstrasse 1 • CH-8002 Zurich • Switzerland Tel. +41-43311 4511 • Fax +41-43311 4545 • [email protected] • www.tracopower.com Page 3