VAISH VT98001Q

Advance Information
VT98001
Multifrequency Synthesizer
Applications
•=
•=
Set-top boxes
MPEG Video clock source
General Description
The Vaishali VT98001 is a single-chip, integrated multiple Phase Locked Loop (PLL) clock synthesizer. The
device uses an analog Phase Locked Loop (PLL) to accept a 27 MHz crystal input to produce multiple
outputs. Selection pins are used to provide various outputs.
Features
•=
24.576 MHz for Firewire IEEE1394 or video
digitizer
•=
18.432 MHz for audio processor
•=
•=
2kHz standby clock
24.576 MHz / 28.224 MHz for software or
hardware modem
•=
•=
Zero ppm synthesis error in all clocks
(except the 2 kHz standby clock)
27 MHz buffered output clock
•=
•=
5V tolerant inputs
6.000MHz buffered output clock
•=
20-pin, 150 mil SSOP (QSOP)
Figure 1. Functional Block Diagram
VDD1
VDD2
VDD3
VDD4
ROM Table
Buffer
X2
24.576/
28.224 MHz
Select
24/28 MHz
osc
27 MHz
Crystal
PLL
Multiplier
Buffer
24.576 MHz
MODE
X1
18.432MHz/
6.000MHz
Buffer
Divider
/PD
Buffer
2kHz
Buffer
27 MHz
Buffer
27 MHz
GND1 GND2 GND3 GND4 GND5
Page 1
MDST-0013-00
www.vaishali.com
Vaishali Semiconductor 747 Camden Avenue, Suite C Campbell CA 95008 Ph. 408.377.6060 Fax 408.377.6063
2001-07-25
VT98001
Advance Information
Figure 2. Pin Configuration
VT98001
Select 24/28MHz
1
20
X2
X1
2
19
3
18
VDD1
VDD2
GND1
4
17
5
6
16
15
GND2
7
14
GND3
24.576MHz
8
13
18.432MHz/6.000MHz
9
10
12
/PD
11
2kHz
MODE
24.576MHz/28.224MHz
GND5
27MHz
27MHz
VDD4
VDD3
GND4
Table 1. Pin Description
Name
Pin #
Type
Description
Select 24/28 MHz
1
I(PU)
Select 24.576 MHz or 28.224 MHz output
X2
2
O
Crystal connection. Connect to a 27 MHz crystal
X1
3
I
Crystal connection. Connect to a 27 MHz crystal
VDD1
4
P
Connect to 3.3V
VDD2
5
P
Connect to VDD
GND1
6
P
Connect to ground
GND2
7
P
Connect to ground
24.576 MHz
8
O
Clock output, 24.576 MHz
MODE
9
I(PU)
Mode control. See Table 2
24.576 MHz/ 28.224MHz
10
O
Clock output, 24.576 MHz or 28.224 MHz
2 kHz
11
O
Clock output, 2 kHz
(1)
/PD
12
I(PU)
18.432MHz/6.000MHz
13
O
Clock output, 18.432 MHz or 6.000 MHz
GND3
14
P
Connect to ground
GND4
15
P
Connect to ground
VDD3
16
P
Connect to VDD
VDD4
17
P
Connect to VDD
18,19
O
27 MHz buffered clock outputs
20
P
Connect to ground
27 MHz
GND5
Powerdown control. When LOW, all clocks are disabled except
2kHz standby clock
Legend: I = Input
O = Output
P = Power supply connection
I(PU) = Input with a 250k ohm pull up
Note (1). All disabled clock outputs are tristated (high impedance).
Page 2
MDST-0013-00
www.vaishali.com
Vaishali Semiconductor 747 Camden Avenue, Suite C Campbell CA 95008 Ph. 408.377.6060 Fax 408.377.6063
2001-07-25
VT98001
Advance Information
Table 2. Mode Control and Frequency Selection Table (/PD = HIGH)
(3)
(1,2)
Outputs
Control
Pin 9
Pin 1
Pin 10
Pin 13
Mode
(Select 24/28MHz).
(24.576 MHz / 28.224 MHz)
(18.43 MHz / 6 MHz)
0
0
High Impedance
0
1
1
0
24.576 MHz
1
1
28.224 MHz
18.432 MHz
6 MHz
Notes: 1. 27MHz (Pins 18 &19) and 24.576 MHz (Pin 8) are active, unless /PD = LOW
2. 2 kHz standby clock is always active, independent of /PD logic state
3. 0 = Low, 1 = HIGH
Table 3. Recommended Crystal Specification
Frequency accuracy is directly proportional to the capacitive load (CL) of the crystal.
Parameter
Definition
Frequency at CL, FL
Defines the series resonant
frequency at CL
Total accuracy: includes initial
accuracy @ 25ºC, aging, and
temperature drift (25ºC to 70ºC)
Maximum deviation from
nominal frequency @ 25ºC,
taking in to account aging,
and temperature drift
Load Capacitance CL
Capacitive load for nominal
frequency FL
C1
Motional capacitance of the
crystal
C0
ESR
Min
Typ
Max
27.000
Units
MHz
40
20
ppm
pf
TBD
pf
Shunt capacitance of the
crystal
7
pf
Equivalent Series
Resistance of the crystal
40
ohms
Table 4. Operating Conditions
Parameter
Conditions
Min
Typ
Max
Units
Power Supply Voltage, VDD
3.0
3.3
3.6
V
Input High Voltage, VIH
2.0
VDD
V
0.8
V
Input Low Voltage, VIL
Operating Temperature,TA
0
25
70
ºC
Typ
Max
Units
Table 5. Electrical Characteristics
Symbol
Min
Output voltage high IOH = -8 mA
Parameter
VOH
2.7
Output voltage low IOL = 8 mA
VOL
0.4
V
Maximum input capacitance (X1,X2)
Cin
3
pF
Power consumption (operating)
Idd1
mA
Power consumption (powerdown)
Idd2
mA
V
Page 3
MDST-0013-00
www.vaishali.com
Vaishali Semiconductor 747 Camden Avenue, Suite C Campbell CA 95008 Ph. 408.377.6060 Fax 408.377.6063
2001-07-25
VT98001
Advance Information
Table 6. Phase Noise Requirements (Crystal phase noise must be less than −130 dBc/Hz @ 10kHz)
Parameter
Symbol
Min
Typ
Max
Units
27 MHz
-120
dBc/Hz @ 10 kHz
24.576 MHz
-100
dBc/Hz @ 10 kHz
24.576/28.224 MHz
-100
dBc/Hz @ 10 kHz
18.432/6.000 MHz
-100
dBc/Hz @ 10 kHz
Table 7. Output Accuracies (Excluding crystal accuracy)
Parameter
Symbol
Min
Typ
Max
Units
24.576/28.224 MHz
0
ppm
2kHz
50
%
18.432/6.000 MHz
0
ppm
27 MHz
0
ppm
Table 8 AC Characteristics
All @Cload = 20 pF, VDD = 3.0V to 3.6V
Parameter
Symbol
Duty Cycle @ VDD/2
δ
Rise time ( measured between 0.8V
and 2.0V)
Tr
Fall time ( measured between 0.8V
and 2.0V)
Tf
PLL lock time
Min
Typ
Max
Units
45/55
%
1
2.5
ns
1
2.5
ns
Tlock
Time to clock outputs after VDD is
available
ms
Tst
50
ms
Ordering Information
Part Number
VT98001Q
VT98001QX
Marking
VT98001Q
VT98001Q
Shipping/Packaging
Tubes
Tape & Reel
No. of Pins
20
20
Package
QSOP
QSOP
Temperature
0°C to +70°C
0°C to +70°C
Page 4
MDST-0013-00
www.vaishali.com
Vaishali Semiconductor 747 Camden Avenue, Suite C Campbell CA 95008 Ph. 408.377.6060 Fax 408.377.6063
2001-07-25