ZARLINK P60ARM-B

ARM60
Data Sheet
Zarlink Part Number: P60ARM-B/IG/GP1N
Notes
1)
The original P60ARM/CG/GPFR is obsolete
2)
This datasheet includes the performance data previously supplied in supplement
MS4396 - Jan 1996
Preface
The ARM60 is a low power, general purpose 32-bit RISC microprocessor. It is an implementation of the
ARM6 macrocell, packaged in a 100 pin Metric Quad Flat Pack. Its simple, elegant and fully static design is
particularly suitable for cost and power sensitive applications .
❏ 32 bit RISC processor
❏ 32 bit data bus
Address Register
❏ 32 bit address bus
❏ Big and Little Endian operating modes
Address
Incrementer
Register Bank
Instruction
Decoder
&
Logic
Control
❏ High performance RISC
21 MIPS sustained @ 30MHz (30 MIPS peak) @ 5V
❏ Low power consumption
1.5mA/MHz @ 5V fabricated in 1µm CMOS
❏ Fully static operation
ideal for power sensitive applications
Booth’s
Multiplier
❏ Fast interrupt response
for real-time applications
Barrel
Shifter
❏ Virtual Memory System Support
32 bit ALU
Write Data Register
Instruction
Pipeline &
Read Data
Register
❏ Excellent high-level language support
❏ Simple but powerful instruction set
❏ IEEE 1149.1 (JTAG) Boundary Scan
to ease testing
Applications:
The ARM60 is ideally suited to those applications requiring RISC performance from a compact, power
efficient processor. These include:
Telecomms - eg GSM terminal controller
Datacomms - eg protocol conversion
Portable Computing - eg palmtop computer
Portable Instruments - eg handheld data acquisition unit
Automotive - eg engine management unit
Consumer Multimedia - low cost controller
Preface-ii
Table of Contents
1.0
Introduction
1
1.1
1.2
2
3
ARM60 Block diagram
ARM60 Functional Diagram
2.0
Signal Description
5
3.0
Programmer's Model
9
3.1
3.2
3.3
3.4
3.5
4.0
5.0
6.0
7.0
Hardware Configuration
Operating Mode Selection
Registers
Exceptions
Reset
9
9
10
13
17
Instruction Set
19
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.10
4.11
4.12
4.13
4.14
4.15
19
20
21
23
30
34
36
41
48
50
52
54
57
59
60
Instruction Set Summary
The Condition Field
Branch and Branch with link (B, BL)
Data processing
PSR Transfer (MRS, MSR)
Multiply and Multiply-Accumulate (MUL, MLA)
Single data transfer (LDR, STR)
Block data transfer (LDM, STM)
Single data swap (SWP)
Software interrupt (SWI)
Coprocessor data operations (CDP)
Coprocessor data transfers (LDC, STC)
Coprocessor register transfers (MRC, MCR)
Undefined instruction
Instruction Set Examples
Memory Interface
65
5.1
5.2
5.3
5.4
5.5
5.6
65
66
68
68
69
69
Cycle types
Byte addressing
Address timing
Memory management
Locked operations
Stretching access times
Coprocessor Interface
71
6.1
6.2
6.3
6.4
6.5
6.6
71
72
72
72
72
73
Interface signals
Data transfer cycles
Register transfer cycle
Privileged instructions
Idempotency
Undefined instructions
Instruction Cycle Operations
75
7.1
7.2
7.3
7.4
7.5
75
75
77
77
78
Branch and branch with link
Data Operations
Multiply and multiply accumulate
Load register
Store register
iii
P60ARM-B
7.6
7.7
7.8
7.9
7.10
7.11
7.12
7.13
7.14
7.15
7.16
7.17
8.0
9.0
79
81
81
82
83
83
85
86
86
87
87
88
Boundary Scan Test Interface
89
8.1
8.2
8.3
8.4
8.5
8.6
8.7
89
90
90
90
90
94
97
Overview
Reset
Pullup Resistors
Instruction Register
Public Instructions
Test Data Registers
Boundary Scan Interface Signals
DC Parameters
9.1
9.2
10.0
Load multiple registers
Store multiple registers
Data swap
Software interrupt and exception entry
Coprocessor data operation
Coprocessor data transfer (from memory to coprocessor)
Coprocessor data transfer (from coprocessor to memory)
Coprocessor register transfer (Load from coprocessor)
Coprocessor register transfer (Store to coprocessor)
Undefined instructions and coprocessor absent
Unexecuted instructions
Instruction Speed Summary
Absolute Maximum Ratings
DC Operating Conditions
AC Parameters
10.1
Notes on AC Parameters
101
101
101
105
112
11.0
Physical Details
113
12.0
Pinout
115
13.0
Appendix - Backward Compatibility
117
iv
Introduction
1.0 Introduction
The ARM60 is part of the Advanced RISC Machines (ARM) family of general purpose 32-bit
microprocessors, which offer very low power consumption and price for high performance devices. The
architecture is based on Reduced Instruction Set Computer (RISC) principles, and the instruction set and
related decode mechanism are much simpler in comparison with microprogrammed Complex Instruction
Set Computers. This results in a high instruction throughput and impressive real-time interrupt response
from a small and cost-effective chip.
The instruction set comprises eleven basic instruction types:
¥
Two of these make use of the on-chip arithmetic logic unit, barrel shifter and multiplier to perform
high-speed operations on the data in a bank of 31 registers, each 32 bits wide;
¥
Three classes of instruction control data transfer between memory and the registers, one optimised
for flexibility of addressing, another for rapid context switching and the third for swapping data;
¥
Three instructions control the flow and privilege level of execution; and
¥
Three types are dedicated to the control of external coprocessors which allow the functionality of
the instruction set to be extended off-chip in an open and uniform way.
The ARM instruction set is a good target for compilers of many different high-level languages. Where
required for critical code segments, assembly code programming is also straightforward, unlike some RISC
processors which depend on sophisticated compiler technology to manage complicated instruction
interdependencies.
Pipelining is employed so that all parts of the processing and memory systems can operate continuously.
Typically, while one instruction is being executed, its successor is being decoded, and a third instruction is
being fetched from memory.
The memory interface has been designed to allow the performance potential to be realised without
incurring high costs in the memory system. Speed critical control signals are pipelined to allow system
control functions to be implemented in standard low-power logic, and these control signals facilitate the
exploitation of the fast access modes offered by industry standard dynamic RAMs.
ARM60 has a 32 bit address bus. All ARM processors share the same instruction set, and ARM60 can be
configured to use a 26 bit address bus for backwards compatibility with earlier processors.
ARM60 is a fully static CMOS implementation of the ARM which allows the clock to be stopped in any part
of the cycle with extremely low residual power consumption and no loss of state.
Notation:
0x
BOLD
binary
- marks a Hexadecimal quantity
- external signals are shown in bold capital letters
- where it is not clear that a quantity is binary it is followed by the word binary
1
P60ARM-B
1.1 ARM60 Block diagram
A[31:0]
ALE
ABE
TCK
Address Register
P
C
B
u
s
Address
Incrementer
TMS
TDI
nTRST
TDO
B
u
s
Register Bank
(31 x 32bit registers)
(6 status registers)
A
L
U
Boundary
Scan
Logic
I
n
c
r
e
m
e
n
t
e
r
LATEABT
DATA32
BIGEND
B
u
s
PROG32
MCLK
nWAIT
A
BoothÕs
Multiplier
B
b
u
s
b
u
s
Instruction
Decoder
&
Control
Logic
nRW
nBW
nIRQ
nFIQ
nRESET
ABORT
Barrel
Shifter
nOPC
nTRANS
nMREQ
SEQ
32 bit ALU
LOCK
nCPI
CPA
CPB
nM[4:0]
Instruction Pipeline
& Read Data Register
Write Data Register
DBE
D[31:0]
Figure 1: ARM60 Block Diagram
2
Introduction
1.2 ARM60 Functional Diagram
TCK
Clocks
MCLK
TMS
nWAIT
TDI
nTRST
Boundary
Scan
TDO
PROG32
Configuration
DATA32
A[31:0]
BIGEND
LATEABT
D[31:0]
nIRQ
Interrupts
nMREQ
nFIQ
ARM60
Memory
Interface
SEQ
nRW
nRESET
nBW
LOCK
ALE
Bus
Controls
DBE
nTRANS
ABE
ABORT
Memory
Management
Interface
nOPC
Power
VDD
nCPI
VSS
CPA
Coprocessor
Interface
CPB
Figure 2: ARM60 Functional Diagram
3
P60ARM-B
4
Signal Description
2.0 Signal Description
Name
Type
Description
OS8
Addresses. This is the processor address bus. If ALE (address latch enable) is HIGH, the
addresses become valid during phase 2 of the cycle before the one to which they refer and
remain so during phase 1 of the referenced cycle. Their stable period may be controlled by
ALE as described below. Refer to section "AC parameters" for timing diagrams.
ABE
I
Address bus enable. This is an input signal which, when LOW, puts the address bus drivers
into a high impedance state. ABE must be tied HIGH when there is no system requirement
to turn off the address drivers.
ABORT
I
Memory ABORT. This is an input which allows the memory system to tell the processor that
a requested access is not allowed. ARM60 can be configured to accept either early aborts for
compatibility with earlier processors or late aborts for greater flexibility.
ALE
I
Address latch enable. This input is used to control transparent latches on the address outputs.
Normally the addresses change during phase 2 to the value required during the next cycle,
but for direct interfacing to ROMs they are required to be stable to the end of phase 2. Taking
ALE LOW until the end of phase 2 will ensure that this happens. If the system does not
require address lines to be held in this way, ALE must be tied HIGH. The address latch is
static, so ALE may be held LOW for long periods to freeze addresses.
BIGEND
I
Big Endian configuration. When this signal is HIGH the processor treats bytes in memory as
being in Big Endian format. When it is LOW memory is treated as Little Endian.
CPA
I
Coprocessor absent. A coprocessor which is capable of performing the operation that ARM60
is requesting (by asserting nCPI) should take CPA LOW immediately. If CPA is HIGH at the
end of phase 1 of the cycle in which nCPI went LOW, ARM60 will abort the coprocessor
handshake and take the undefined instruction trap. If CPA is LOW and remains LOW,
ARM60 will busy-wait until CPB is LOW and then complete the coprocessor instruction.
CPB
I
Coprocessor busy. A coprocessor which is capable of performing the operation which
ARM60 is requesting (by asserting nCPI), but cannot commit to starting it immediately,
should indicate this by driving CPB HIGH. When the coprocessor is ready to start it should
take CPB LOW. ARM60 samples CPB at the end of phase 1 of each cycle in which nCPI is
LOW.
I/
OS8
Data Bus. These are bidirectional signal paths which are used for data transfers between the
processor and external memory. During read cycles (when nRW is LOW), the input data
must be valid before the end of phase 2 of the transfer cycle. During write cycles (when nRW
is HIGH), the output data will become valid during phase 1 and remain valid throughout
phase 2 of the transfer cycle.
I
32 bit Data configuration. When this signal is HIGH the processor can access data in a 32 bit
address space using address lines A[31:0]. When it is LOW the processor can access data from
a 26 bit address space using A[25:0]. In this latter configuration the address lines A[31:26] are
not used. Before changing DATA32, ensure that the processor is not about to access an
address greater that 0x3FFFFFF in the next cycle.
A[31:0]
D[31:0]
DATA32
Table 1: Signal Description
5
P60ARM-B
Name
Type
Description
DBE
I
Data bus enable. When DBE is LOW the write data register output drivers are disabled.
When DBE goes HIGH these output drivers are enabled. DBE facilitates data bus sharing for
DMA and so on.
LATEABT
I
Late abort. This signal controls the action of the processor on an abort exception. When it is
HIGH (Late abort) the modified base register of an aborted LDR or STR instruction is written
back. When it is LOW (Early abort) the modified base register is not written back. LATEABT
must not be changed during the execution of a data access instruction where abort is active.
It is recommended that the Late abort scheme be used where possible as this scheme will be
used in future ARM processors.
LOCK
OS8
Locked operation. When LOCK is HIGH, the processor is performing a ÒlockedÓ memory
access, and the memory controller must wait until LOCK goes LOW before allowing another
device to access the memory.LOCK changes while MCLK is HIGH, and remains HIGH for
the duration of the locked memory accesses. It is active only during the data swap (SWP)
instruction.
MCLK
I
Memory clock input. This clock times all ARM60 memory accesses and internal operations.
The clock has two distinct phases - phase 1 in which MCLK is LOW and phase 2 in which
MCLK (and nWAIT) is HIGH. The clock may be stretched indefinitely in either phase to
allow access to slow peripherals or memory. Alternatively, the nWAIT input may be used
with a free running MCLK to achieve the same effect.
nBW
OS8
Not byte/word. This is an output signal used by the processor to indicate to the external
memory system when a data transfer of a byte length is required. The signal is HIGH for
word transfers and LOW for byte transfers and is valid for both read and write cycles. The
signal will become valid during phase 2 of the cycle before the one in which the transfer will
take place. It will remain stable throughout phase 1 of the transfer cycle.
nCPI
O4
Not Coprocessor instruction. When ARM60 executes a coprocessor instruction, it will take
this output LOW and wait for a response from the coprocessor. The action taken will depend
on this response, which the coprocessor signals on the CPA and CPB inputs.
nFIQ
I
Not fast interrupt request. This is an asynchronous interrupt request to the processor which
causes it to be interrupted if taken LOW when the appropriate enable in the processor is
active. The signal is level sensitive and must be held LOW until a suitable response is
received from the processor.
nIRQ
I
Not interrupt request. As nFIQ, but with lower priority. May be taken LOW asynchronously
to interrupt the processor when the appropriate enable is active.
nMREQ
O4
Not memory request. This signal, when LOW, indicates that the processor requires memory
access during the following cycle. The signal becomes valid during phase 1, remaining valid
through phase 2 of the cycle preceding that to which it refers.
nOPC
O4
Not op-code fetch. When LOW this signal indicates that the processor is fetching an
instruction from memory; when HIGH, data (if present) is being transferred. The signal
becomes valid during phase 2 of the previous cycle, remaining valid through phase 1 of the
referenced cycle.
Table 1: Signal Description
6
Signal Description
Name
Type
Description
I
Not reset. This is a level sensitive input signal which is used to start the processor from a
known address. A LOW level will cause the instruction being executed to terminate
abnormally. When nRESET becomes HIGH for at least one clock cycle, the processor will restart from address 0. nRESET must remain LOW (and nWAIT must remain HIGH) for at
least two clock cycles. During the LOW period the processor will perform dummy instruction
fetches with the address incrementing from the point where reset was activated. The address
will overflow to zero if nRESET is held beyond the maximum address limit.
nRW
OS8
Not read/write.When HIGH this signal indicates a processor write cycle; when LOW, a read
cycle. It becomes valid during phase 2 of the cycle before that to which it refers, and remains
valid to the end of phase 1 of the referenced cycle.
nTRANS
OS8
Not memory translate. When this signal is LOW it indicates that the processor is in user
mode. It may be used to tell memory management hardware when translation of the
addresses should be turned on, or as an indicator of non-user mode activity.
nTRST
IP
NOT Test Reset. Active-low reset signal for the boundary scan logic. This pin must be pulsed
or driven low to achieve normal device operation, in addition to the normal device reset
(nRESET). The action of this and the other four boundary scan signals are described in more
detail later in this document.
nWAIT
I
Not wait. When accessing slow peripherals, ARM60 can be made to wait for an integer
number of MCLK cycles by driving nWAIT LOW. Internally, nWAIT is ANDed with MCLK
and must only change when MCLK is LOW. If nWAIT is not used it must be tied HIGH.
PROG32
I
32 bit Program configuration. When this signal is HIGH the processor can fetch instructions
from a 32 bit address space using address lines A[31:0]. When it is LOW the processor fetches
instructions from a 26 bit address space using A[25:0]. In this latter configuration the address
lines A[31:26] are not used for instruction fetches. Before changing PROG32, ensure that the
processor is in a 26 bit mode, and is not about to write to an address in the range 0 to 0x1F
(inclusive) in the next cycle.
O4
Sequential address. This output signal will become HIGH when the address of the next
memory cycle will be related to that of the last memory access. The new address will either
be the same as or 4 greater than the old one.
nRESET
SEQ
The signal becomes valid during phase 1 and remains so through phase 2 of the cycle before
the cycle whose address it anticipates. It may be used, in combination with the low-order
address lines, to indicate that the next cycle can use a fast memory mode (for example DRAM
page mode) and/or to bypass the address translation system.
TCK
IP
Test Clock.
TDI
IP
Test Data Input.
TDO
OS8
TMS
IP
Test Mode Select.
VDD
P
Power supply. These connections provide power to the device.
VSS
P
Ground. These connections are the ground reference for all signals.
Test Data Output. Output from the boundary scan logic.
Table 1: Signal Description
7
P60ARM-B
Key to Signal Types:
I - Input
IP - Input with pull-up resistor (35kΩ - 100kΩ)
O4 - Output (4mA drive)
OS8 - slew-limited output (8mA drive)
P - Power
8
Programmer's Model
3.0 Programmer's Model
ARM60 supports a variety of operating configurations. Some are controlled by inputs and are known as the
hardware configurations. Others may be controlled by software and these are known as operating modes.
3.1 Hardware ConÞguration
The ARM60 processor provides 4 hardware configurations which may be changed while the processor is
running and which are detailed in Chapter 4.0 Instruction Set.
The BIGEND input sets whether the ARM60 treats words in memory as being stored in Big Endian or Little
Endian format. Memory is viewed as a linear collection of bytes numbered upwards from zero. Bytes 0 to
3 hold the first stored word, bytes 4 to 7 the second and so on.
In the Little Endian scheme the lowest numbered byte in a word is considered to be the least significant byte
of the word and the highest numbered byte is the most significant. Byte 0 of the memory system should be
connected to data lines 7 through 0 (D[7:0]) in this scheme.
In the Big Endian scheme the most significant byte of a word is stored at the lowest numbered byte and the
least significant byte is stored at the highest numbered byte. Byte 0 of the memory system should therefore
be connected to data lines 31 through 24 (D[31:24]).
The LATEABT input sets the processor's behaviour when a data abort exception occurs. It only affects the
behaviour of load/store register instructions and is discussed more fully in Chapter 3.0 Programmer's Model
and Chapter 4.0 Instruction Set.
The other two inputs, PROG32 and DATA32 are used for backward compatibility with earlier ARM
processors (see 13.0 Appendix - Backward Compatibility) but should normally be set to 1. This configuration
extends the address space to 32 bits, introduces major changes in the programmer's model as described
below and provides support for running existing 26 bit programs in the 32 bit environment. This mode is
recommended for compatibility with future ARM processors and all new code should be written to use
only the 32 bit operating modes.
Because the original ARM instruction set has been modified to accommodate 32 bit operation there are
certain additional restrictions which programmers must be aware of. These are indicated in the text by the
words shall and shall not. Reference should also be made to the ARM Application Notes ÒRules for ARM Code
WritersÓ and ÒNotes for ARM Code WritersÓ available from your supplier.
3.2 Operating Mode Selection
ARM60 has a 32 bit data bus and a 32 bit address bus. The data types the processor supports are Bytes (8
bits) and Words (32 bits), where words must be aligned to four byte boundaries. Instructions are exactly
one word, and data operations (e.g. ADD) are only performed on word quantities. Load and store
operations can transfer either bytes or words.
9
P60ARM-B
ARM60 supports six modes of operation:
(1)
User mode (usr): the normal program execution state
(2)
FIQ mode (fiq): designed to support a data transfer or channel process
(3)
IRQ mode (irq): used for general purpose interrupt handling
(4)
Supervisor mode (svc): a protected mode for the operating system
(5)
Abort mode (abt): entered after a data or instruction prefetch abort
(6)
Undefined mode (und): entered when an undefined instruction is executed
Mode changes may be made under software control or may be brought about by external interrupts or
exception processing. Most application programs will execute in User mode. The other modes, known as
privileged modes, will be entered to service interrupts or exceptions or to access protected resources.
3.3 Registers
The processor has a total of 37 registers made up of 31 general 32 bit registers and 6 status registers. At any
one time 16 general registers (R0 to R15) and one or two status registers are visible to the programmer. The
visible registers depend on the processor mode and the other registers (the banked registers) are switched in
to support IRQ, FIQ, Supervisor, Abort and Undefined mode processing. The register bank organisation is
shown in Figure 3: Register Organisation. The banked registers are shaded in the diagram.
In all modes 16 registers, R0 to R15, are directly accessible. All registers except R15 are general purpose and
may be used to hold data or address values. Register R15 holds the Program Counter (PC). When R15 is
read, bits [1:0] are zero and bits [31:2] contain the PC. A seventeenth register (the CPSR - Current Program
Status Register) is also accessible. It contains condition code flags and the current mode bits and may be
thought of as an extension to the PC.
R14 is used as the subroutine link register and receives a copy of R15 when a Branch and Link instruction
is executed. It may be treated as a general purpose register at all other times. R14_svc, R14_irq, R14_fiq,
R14_abt and R14_und are used similarly to hold the return values of R15 when interrupts and exceptions
arise, or when Branch and Link instructions are executed within interrupt or exception routines.
10
Programmer's Model
General Registers and Program Counter
User32
FIQ32
Supervisor32
Abort32
IRQ32
Undefined32
R0
R0
R0
R0
R0
R0
R1
R1
R1
R1
R1
R1
R2
R2
R2
R2
R2
R2
R3
R3
R3
R3
R3
R3
R4
R4
R4
R4
R4
R4
R5
R5
R5
R5
R5
R5
R6
R6
R6
R6
R6
R6
R7
R7
R7
R7
R7
R7
R8
R8_fiq
R8
R8
R8
R8
R9
R9_fiq
R9
R9
R9
R9
R10
R10_fiq
R10
R10
R10
R10
R11
R11_fiq
R11
R11
R11
R11
R12
R12_fiq
R12
R12
R12
R12
R13
R13_fiq
R13_svc
R13_abt
R13_irq
R13_und
R14
R14_fiq
R14_svc
R14_abt
R14_irq
R14_und
R15 (PC)
R15 (PC)
R15 (PC)
R15 (PC)
R15 (PC)
R15 (PC)
Program Status Registers
CPSR
CPSR
CPSR
CPSR
CPSR
CPSR
SPSR_fiq
SPSR_svc
SPSR_abt
SPSR_irq
SPSR_und
Figure 3: Register Organisation
FIQ mode has seven banked registers mapped to R8-14 (R8_fiq-R14_fiq). Many FIQ programs will not need
to save any registers. User mode, IRQ mode, Supervisor mode, Abort mode and Undefined mode each have
two banked registers mapped to R13 and R14. The two banked registers allow these modes to each have a
private stack pointer and link register. Supervisor, IRQ, Abort and Undefined mode programs which
require more than these two banked registers are expected to save some or all of the caller's registers (R0 to
R12) on their respective stacks. They are then free to use these registers which they will restore before
returning to the caller. In addition there are also five SPSRs (Saved Program Status Registers) which are
loaded with the CPSR when an exception occurs. There is one SPSR for each privileged mode. Thus the
CPSR of the calling mode can be easily restored when the current (privileged) mode is exited.
11
P60ARM-B
flags
control
31
30
29
28
27
N
Z
C
V
.
.
8
7
6
5
4
3
2
1
0
.
I
F
.
M4
M3
M2
M1
M0
Overflow
Carry / Borrow / Extend
Zero
Negative / Less Than
Mode bits
FIQ disable
IRQ disable
Figure 4: Format of the Program Status Registers (PSRs)
The format of the Program Status Registers is shown in Figure 4: Format of the Program Status Registers
(PSRs). The N, Z, C and V bits are the condition code flags. The condition code flags in the CPSR may be
changed as a result of arithmetic and logical operations in the processor and may be tested by all
instructions to determine if the instruction is to be executed.
The I and F bits are the interrupt disable bits. The I bit disables IRQ interrupts when it is set and the F bit
disables FIQ interrupts when it is set. The M0, M1, M2, M3 and M4 bits (M[4:0]) are the mode bits, and these
determine the mode in which the processor operates. The interpretation of the mode bits is shown in Table
2: The Mode Bits. Not all combinations of the mode bits define a valid processor mode. Only those explicitly
described shall be used.
The bottom 28 bits of a PSR (incorporating I, F and M[4:0]) are known collectively as the control bits. The
control bits will change when an exception arises and in addition can be manipulated by software when the
processor is in a privileged mode. Unused bits in the PSRs are reserved and their state shall be preserved
when changing the flag or control bits. Programs shall not rely on specific values from the reserved bits
when checking the PSR status, since they may read as one or zero in future processors.
M[4:0]
Mode
Accessible register set
10000
User
PC, R14..R0
CPSR
10001
FIQ
PC, R14_fiq..R8_fiq, R7..R0
CPSR, SPSR_fiq
10010
IRQ
PC, R14_irq..R13_irq, R12..R0
CPSR, SPSR_irq
10011
Supervisor
PC, R14_svc..R13_svc, R12..R0
CPSR, SPSR_svc
10111
Abort
PC, R14_abt..R13_abt, R12..R0
CPSR, SPSR_abt
11011
Undefined
PC, R14_und..R13_und, R12..R0
CPSR, SPSR_und
Table 2: The Mode Bits
12
Programmer's Model
3.4 Exceptions
Exceptions arise whenever there is a need for the normal flow of program execution to be broken, so that
(for example) the processor can be diverted to handle an interrupt from a peripheral. The processor state
just prior to handling the exception must be preserved so that the original program can be resumed when
the exception routine has completed. Many exceptions may arise at the same time.
ARM60 handles exceptions by making use of the banked registers to save state. The old PC and CPSR
contents are copied into the appropriate R14 and SPSR and the PC and mode bits in the CPSR bits are forced
to a value which depends on the exception. Interrupt disable flags are set where required to prevent
otherwise unmanageable nestings of exceptions. In the case of a re-entrant interrupt handler, R14 and the
SPSR should be saved onto a stack in main memory before re-enabling the interrupt; when transferring the
SPSR register to and from a stack, it is important to transfer the whole 32 bit value, and not just the flag or
control fields. When multiple exceptions arise simultaneously, a fixed priority determines the order in
which they are handled. The priorities are listed later in this chapter.
3.4.1 FIQ
The FIQ (Fast Interrupt reQuest) exception is externally generated by taking the nFIQ input LOW. This
input can accept asynchronous transitions, and is delayed by one clock cycle for synchronisation before it
can affect the processor execution flow. It is designed to support a data transfer or channel process, and has
sufficient private registers to remove the need for register saving in such applications (thus minimising the
overhead of context switching). The FIQ exception may be disabled by setting the F flag in the CPSR (but
note that this is not possible from User mode). If the F flag is clear, ARM60 checks for a LOW level on the
output of the FIQ synchroniser at the end of each instruction.
When a FIQ is detected, ARM60 performs the following:
(1)
Saves the address of the next instruction to be executed plus 4 in R14_fiq; saves CPSR in SPSR_fiq
(2)
Forces M[4:0]=10001 (FIQ mode) and sets the F and I bits in the CPSR
(3)
Forces the PC to fetch the next instruction from address 0x1C
To return normally from FIQ, use SUBS PC, R14_fiq,#4 which will restore both the PC (from R14) and the
CPSR (from SPSR_fiq) and resume execution of the interrupted code. R14_fiq is a symbol for the register
R14 and if used needs to be declared in the users application program.
3.4.2 IRQ
The IRQ (Interrupt ReQuest) exception is a normal interrupt caused by a LOW level on the nIRQ input. It
has a lower priority than FIQ, and is masked out when a FIQ sequence is entered. Its effect may be masked
out at any time by setting the I bit in the CPSR (but note that this is not possible from User mode). If the I
flag is clear, ARM60 checks for a LOW level on the output of the IRQ synchroniser at the end of each
instruction. When an IRQ is detected, ARM60 performs the following:
(1)
Saves the address of the next instruction to be executed plus 4 in R14_irq; saves CPSR in SPSR_irq
(2)
Forces M[4:0]=10010 (IRQ mode) and sets the I bit in the CPSR
(3)
Forces the PC to fetch the next instruction from address 0x18
13
P60ARM-B
To return normally from IRQ, use SUBS PC,R14_irq,#4 which will restore both the PC and the CPSR and
resume execution of the interrupted code. R14_fiq is a symbol for the register R14 and if used needs to be
declared in the users application program.
3.4.3 Abort
An ABORT can be signalled by the external ABORT input. ABORT indicates that the current memory
access cannot be completed. For instance, in a virtual memory system the data corresponding to the current
address may have been moved out of memory onto a disc, and considerable processor activity may be
required to recover the data before the access can be performed successfully. ARM60 checks for ABORT
during memory access cycles. When successfully aborted ARM60 will respond in one of two ways:
(1)
If the abort occurred during an instruction prefetch (a Prefetch Abort), the prefetched instruction is
marked as invalid but the abort exception does not occur immediately. If the instruction is not
executed, for example as a result of a branch being taken while it is in the pipeline, no abort will
occur. An abort will take place if the instruction reaches the head of the pipeline and is about to be
executed.
(2)
If the abort occurred during a data access (a Data Abort), the action depends on the instruction type.
(a) Single data transfer instructions (LDR, STR) are aborted as though the instruction had not executed
if the processor is configured for Early Abort. When configured for Late Abort, these instructions
are able to write back modified base registers and the Abort handler must be aware of this.
(b) The swap instruction (SWP) is aborted as though it had not executed, though externally the read
access may take place.
(c) Block data transfer instructions (LDM, STM) complete, and if write-back is set, the base is updated.
If the instruction would normally have overwritten the base with data (i.e. LDM with the base in
the transfer list), this overwriting is prevented. All register overwriting is prevented after the Abort
is indicated, which means in particular that R15 (which is always last to be transferred) is preserved
in an aborted LDM instruction.
When either a prefetch or data abort occurs, ARM60 performs the following:
(1)
Saves the address of the aborted instruction plus 4 (for prefetch aborts) or 8 (for data aborts) in
R14_abt; saves CPSR in SPSR_abt.
(2)
Forces M[4:0]=10111 (Abort mode) and sets the I bit in the CPSR.
(3)
Forces the PC to fetch the next instruction from either address 0x0C (prefetch abort) or address 0x10
(data abort).
To return after fixing the reason for the abort, use SUBS PC,R14_abt,#4 (for a prefetch abort) or SUBS
PC,R14_abt,#8 (for a data abort). This will restore both the PC and the CPSR and retry the aborted
instruction. R14_fiq is a symbol for the register R14 and if used needs to be declared in the users application
program.
The abort mechanism allows a demand paged virtual memory system to be implemented when suitable
memory management software is available. The processor is allowed to generate arbitrary addresses, and
when the data at an address is unavailable the MMU signals an abort. The processor traps into system
14
Programmer's Model
software which must work out the cause of the abort, make the requested data available, and retry the
aborted instruction. The application program needs no knowledge of the amount of memory available to
it, nor is its state in any way affected by the abort.
3.4.4 Software interrupt
The software interrupt instruction (SWI) is used for getting into Supervisor mode, usually to request a
particular supervisor function. When a SWI is executed, ARM60 performs the following:
(1)
Saves the address of the SWI instruction plus 4 in R14_svc; saves CPSR in SPSR_svc
(2)
Forces M[4:0]=10011 (Supervisor mode) and sets the I bit in the CPSR
(3)
Forces the PC to fetch the next instruction from address 0x08
To return from a SWI, use MOVS PC,R14_svc. This will restore the PC and CPSR and return to the
instruction following the SWI.
3.4.5 UndeÞned instruction trap
When the ARM60 comes across an instruction which it cannot handle (see Chapter 4.0 Instruction Set), it
offers it to any coprocessors which may be present. If a coprocessor can perform this instruction but is busy
at that time, ARM60 will wait until the coprocessor is ready or until an interrupt occurs. If no coprocessor
can handle the instruction then ARM60 will take the undefined instruction trap.
The trap may be used for software emulation of a coprocessor in a system which does not have the
coprocessor hardware, or for general purpose instruction set extension by software emulation.
When ARM60 takes the undefined instruction trap it performs the following:
(1)
Saves the address of the Undefined or coprocessor instruction plus 4 in R14_und; saves CPSR in
SPSR_und.
(2)
Forces M[4:0]=11011 (Undefined mode) and sets the I bit in the CPSR
(3)
Forces the PC to fetch the next instruction from address 0x04
To return from this trap after emulating the failed instruction, use MOVS PC,R14_und. This will restore the
CPSR and return to the instruction following the undefined instruction.
15
P60ARM-B
3.4.6 Vector Summary
Address
Exception
Mode on entry
0x00000000
Reset
Supervisor
0x00000004
UndeÞned instruction
UndeÞned
0x00000008
Software interrupt
Supervisor
0x0000000C
Abort (prefetch)
Abort
0x00000010
Abort (data)
Abort
0x00000014
-- reserved --
--
0x00000018
IRQ
IRQ
0x0000001C
FIQ
FIQ
Table 3: Vector Summary
These are byte addresses, and will normally contain a branch instruction pointing to the relevant routine.
The FIQ routine might reside at 0x1C onwards, and thereby avoid the need for (and execution time of) a
branch instruction.
The reserved entry is for an Address Exception vector which is only operative when the processor is
configured for a 26 bit program space. See 13.0 Appendix - Backward Compatibility
3.4.7 Exception Priorities
When multiple exceptions arise at the same time, a fixed priority system determines the order in which they
will be handled:
(1)
Reset (highest priority)
(2)
Data abort
(3)
FIQ
(4)
IRQ
(5)
Prefetch abort
(6)
Undefined Instruction, Software interrupt (lowest priority)
Note that not all exceptions can occur at once. Undefined instruction and software interrupt are mutually
exclusive since they each correspond to particular (non-overlapping) decodings of the current instruction.
If a data abort occurs at the same time as a FIQ, and FIQs are enabled (i.e. the F flag in the CPSR is clear),
ARM60 will enter the data abort handler and then immediately proceed to the FIQ vector. A normal return
from FIQ will cause the data abort handler to resume execution. Placing data abort at a higher priority than
FIQ is necessary to ensure that the transfer error does not escape detection; the time for this exception entry
should be added to worst case FIQ latency calculations.
16
Programmer's Model
3.4.8 Interrupt Latencies
The worst case latency for FIQ, assuming that it is enabled, consists of the longest time the request can take
to pass through the synchroniser (Tsyncmax), plus the time for the longest instruction to complete (Tldm, the
longest instruction is an LDM which loads all the registers including the PC), plus the time for the data abort
entry (Texc), plus the time for FIQ entry (Tfiq). At the end of this time ARM60 will be executing the
instruction at 0x1C.
Tsyncmax is 3 processor cycles, Tldm is 20 cycles, Texc is 3 cycles, and Tfiq is 2 cycles. The total time is
therefore 28 processor cycles. This is just over 1.4 microseconds in a system which uses a continuous 20
MHz processor clock. The maximum IRQ latency calculation is similar, but must allow for the fact that FIQ
has higher priority and could delay entry into the IRQ handling routine for an arbitrary length of time. The
minimum latency for FIQ or IRQ consists of the shortest time the request can take through the synchroniser
(Tsyncmin) plus Tfiq. This is 4 processor cycles.
To reduce the interupt latency, Tldm can be reduced by using an option in the complier which splits LDM
instructions so that it will only load or store a user defined number (between 3 and 16) of registers at any
one time.
If this option is used, then the MUL or MLA instruction can potentially become the longest taking up to 17
cycles, depending on the data being manipulated.
3.5 Reset
When the nRESET signal goes LOW, ARM60 abandons the executing instruction and then continues to
fetch instructions from incrementing word addresses.
When nRESET goes HIGH again, ARM60 does the following:
(1)
Overwrites R14_svc and SPSR_svc by copying the current values of the PC and CPSR into them.
The value of the saved PC and CPSR is not defined.
(2)
Forces M[4:0]=10011 (Supervisor mode) and sets the I and F bits in the CPSR.
(3)
Forces the PC to fetch the next instruction from address 0x00
17
P60ARM-B
18
Instruction Set - Summary
4.0 Instruction Set
4.1 Instruction Set Summary
A summary of the ARM60 instruction set is shown in Figure 5: Instruction Set Summary.
Note:
some instruction codes are not defined but do not cause the Undefined instruction trap to be taken,
for instance a Multiply instruction with bit 6 changed to a 1. These instructions shall not be used,
as their action may change in future ARM implementations.
31
28 27 26 25 24 23 22 21 20 19
Cond
0 0
Opcode
I
Cond
0 0 0 0 0 0
Cond
0 0 0 1 0
Cond
0 1
I
16 15
12 11
8
7
5
4
3
0
Data Processing
PSR Transfer
S
Rn
Rd
A S
Rd
Rn
Rs
1 0 0 1
Rm
Multiply
00
Rn
Rd
0 0 0 0
1 0 0 1
Rm
Single Data Swap
Rn
Rd
B
P U B W L
Cond
0 1 1
Cond
1 0 0
P U S W L
Cond
1 0 1
L
Cond
1 1 0
P U N W L
Cond
1 1 1 0
Cond
1 1 1 0
Cond
1 1 1 1
Operand 2
offset
1
XXXXXXXXXXXXXXXXXXXX
Rn
Single Data Transfer
XXXX
Register List
Block Data Transfer
offset
CP Opc
CP Opc
L
Undefined
Branch
Rn
CRd
CP#
offset
CRn
CRd
CP#
CP
0
CRm
Coproc Data Operation
CRn
Rd
CP#
CP
1
CRm
Coproc Register Transfer
ignored by processor
Coproc Data Transfer
Software Interrupt
Figure 5: Instruction Set Summary
19
P60ARM-B
4.2 The Condition Field
31
28 27
0
Cond
Condition field
0000 = EQ - Z set (equal)
0001 = NE - Z clear (not equal)
0010 = CS - C set (unsigned higher or same)
0011 = CC - C clear (unsigned lower)
0100 = MI - N set (negative)
0101 = PL - N clear (positive or zero)
0110 = VS - V set (overflow)
0111 = VC - V clear (no overflow)
1000 = HI - C set and Z clear (unsigned higher)
1001 = LS - C clear or Z set (unsigned lower or same)
1010 = GE - N set and V set, or N clear and V clear (greater or equal)
1011 = LT - N set and V clear, or N clear and V set (less than)
1100 = GT - Z clear, and either N set and V set, or N clear and V clear (greater than)
1101 = LE - Z set, or N set and V clear, or N clear and V set (less than or equal)
1110 = AL - always
1111 = NV - never
Figure 6: Condition Codes
All ARM60 instructions are conditionally executed, which means that their execution may or may not take
place depending on the values of the N, Z, C and V flags in the CPSR. The condition encoding is shown in
Figure 6: Condition Codes.
If the always (AL) condition is specified, the instruction will be executed irrespective of the flags. The never
(NV) class of condition codes shall not be used as they will be redefined in future variants of the ARM
architecture. If a NOP is required it is suggested that MOV R0,R0 be used. The assembler treats the absence
of a condition code as though always had been specified.
The other condition codes have meanings as detailed in Figure 6: Condition Codes, for instance code 0000
(EQual) causes the instruction to be executed only if the Z flag is set. This would correspond to the case
where a compare (CMP) instruction had found the two operands to be equal. If the two operands were
different, the compare instruction would have cleared the Z flag and the instruction will not be executed.
20
Instruction Set - B, BL
4.3 Branch and Branch with link (B, BL)
The instruction is only executed if the condition is true. The various conditions are defined at the beginning
of this chapter. The instruction encoding is shown in Figure 7: Branch Instructions.
Branch instructions contain a signed 2's complement 24 bit offset. This is shifted left two bits, sign extended
to 32 bits, and added to the PC. The instruction can therefore specify a branch of +/- 32Mbytes. The branch
offset must take account of the prefetch operation, which causes the PC to be 2 words (8 bytes) ahead of the
current instruction.
31
28 27
Cond
25 24 23
101
0
L
offset
Link bit
0 = Branch
1 = Branch with Link
Condition field
Figure 7: Branch Instructions
Branches beyond +/- 32Mbytes must use an offset or absolute destination which has been previously
loaded into a register. In this case the PC should be manually saved in R14 if a Branch with Link type
operation is required.
4.3.1 The link bit
Branch with Link (BL) writes the old PC into the link register (R14) of the current bank. The PC value
written into R14 is adjusted to allow for the prefetch, and contains the address of the instruction following
the branch and link instruction. Note that the CPSR is not saved with the PC.
To return from a routine called by Branch with Link use MOV PC,R14 if the link register is still valid or
LDM Rn!,{..PC} if the link register has been saved onto a stack pointed to by Rn.
4.3.2 Instruction Cycle Times
Branch and Branch with Link instructions take 2S + 1N incremental cycles, where S and N are as defined in
section 5.1 Cycle types on page 65.
4.3.3 Assembler syntax
B{L}{cond} <expression>
{L} is used to request the Branch with Link form of the instruction. If absent, R14 will not be affected by the
instruction.
{cond} is a two-char mnemonic as shown in Figure 6: Condition Codes (EQ, NE, VS etc). If absent then AL
(ALways) will be used.
21
P60ARM-B
<expression> is the destination. The assembler calculates the offset.
Items in {} are optional. Items in <> must be present.
4.3.4 Examples
here
22
BAL
B
here
there
; assembles to 0xEAFFFFFE (note effect of PC offset)
; ALways condition used as default
CMP
BEQ
R1,#0
fred
; compare R1 with zero and branch to fred if R1
; was zero otherwise continue to next instruction
BL
sub+ROM
; call subroutine at computed address
ADDS
BLCC
R1,#1
sub
; add 1 to register 1, setting CPSR flags on the
; result then call subroutine if the C flag is clear,
; which will be the case unless R1 held 0xFFFFFFFF
Instruction Set - Data processing
4.4 Data processing
The instruction is only executed if the condition is true, defined at the beginning of this chapter. The
instruction encoding is shown in Figure 8: Data Processing Instructions.
The instruction produces a result by performing a specified arithmetic or logical operation on one or two
operands. The first operand is always a register (Rn). The second operand may be a shifted register (Rm) or
a rotated 8 bit immediate value (Imm) according to the value of the I bit in the instruction. The condition
codes in the CPSR may be preserved or updated as a result of this instruction, according to the value of the
S bit in the instruction. Certain operations (TST, TEQ, CMP, CMN) do not write the result to Rd. They are
used only to perform tests and to set the condition codes on the result and always have the S bit set. The
instructions and their effects are listed in Table 4: ARM Data Processing Instructions.
31
28 27 26 25 24
Cond
00
I
21 20 19
OpCode
S
16 15
Rn
12 11
0
Rd
Operand 2
Destination register
1st operand register
Set condition codes
0 = do not alter condition codes
1 = set condition codes
Operation Code
0000 = AND - Rd:= Op1 AND Op2
0001 = EOR - Rd:= Op1 EOR Op2
0010 = SUB - Rd:= Op1 - Op2
0011 = RSB - Rd:= Op2 - Op1
0100 = ADD - Rd:= Op1 + Op2
0101 = ADC - Rd:= Op1 + Op2 + C
0110 = SBC - Rd:= Op1 - Op2 + C - 1
0111 = RSC - Rd:= Op2 - Op1 + C - 1
1000 = TST - set condition codes on Op1 AND Op2
1001 = TEQ - set condition codes on Op1 EOR Op2
1010 = CMP - set condition codes on Op1 - Op2
1011 = CMN - set condition codes on Op1 + Op2
1100 = ORR - Rd:= Op1 OR Op2
1101 = MOV - Rd:= Op2
1110 = BIC - Rd:= Op1 AND NOT Op2
1111 = MVN - Rd:= NOT Op2
Immediate Operand
11
0 = operand 2 is a register
4
3
Shift
0
Rm
2nd operand register
shift applied to Rm
11
1 = operand 2 is an immediate value
8 7
Rotate
0
Imm
Unsigned 8 bit immediate value
shift applied to Imm
Condition field
Figure 8: Data Processing Instructions
23
P60ARM-B
4.4.1 CPSR ßags
The data processing operations may be classified as logical or arithmetic. The logical operations (AND,
EOR, TST, TEQ, ORR, MOV, BIC, MVN) perform the logical action on all corresponding bits of the operand
or operands to produce the result. If the S bit is set (and Rd is not R15, see below) the V flag in the CPSR will
be unaffected, the C ßag will be set to the carry out from the barrel shifter (or preserved when the shift
operation is LSL #0), the Z ßag will be set if and only if the result is all zeros, and the N ßag will be set to
the logical value of bit 31 of the result.
Assembler
Mnemonic
Action
OpCode
AND
0000
operand1 AND operand2
EOR
0001
operand1 EOR operand2
SUB
0010
operand1 - operand2
RSB
0011
operand2 - operand1
ADD
0100
operand1 + operand2
ADC
0101
operand1 + operand2 + carry
SBC
0110
operand1 - operand2 + carry - 1
RSC
0111
operand2 - operand1 + carry - 1
TST
1000
as AND, but result is not written
TEQ
1001
as EOR, but result is not written
CMP
1010
as SUB, but result is not written
CMN
1011
as ADD, but result is not written
ORR
1100
operand1 OR operand2
MOV
1101
operand2
BIC
1110
operand1 AND NOT operand2
MVN
1111
NOT operand2
(operand1 is ignored)
(Bit clear)
(operand1 is ignored)
Table 4: ARM Data Processing Instructions
The arithmetic operations (SUB, RSB, ADD, ADC, SBC, RSC, CMP, CMN) treat each operand as a 32 bit
integer (either unsigned or 2's complement signed, the two are equivalent). If the S bit is set (and Rd is not
R15) the V flag in the CPSR will be set if an overflow occurs into bit 31 of the result; this may be ignored if
the operands were considered unsigned, but warns of a possible error if the operands were 2's complement
signed. The C flag will be set to the carry out of bit 31 of the ALU, the Z flag will be set if and only if the
result was zero, and the N flag will be set to the value of bit 31 of the result (indicating a negative result if
the operands are considered to be 2's complement signed).
24
Instruction Set - Shifts
4.4.2 Shifts
When the second operand is specified to be a shifted register, the operation of the barrel shifter is controlled
by the Shift field in the instruction. This field indicates the type of shift to be performed (logical left or right,
arithmetic right or rotate right). The amount by which the register should be shifted may be contained in
an immediate field in the instruction, or in the bottom byte of another register (other than R15). The
encoding for the different shift types is shown in Figure 9: ARM Shift Operations.
11
7 6
5
4
11
0
8
Rs
7
0
Shift type
6
5
4
1
Shift type
00 = logical left
01 = logical right
10 = arithmetic right
11 = rotate right
00 = logical left
01 = logical right
10 = arithmetic right
11 = rotate right
Shift amount
Shift register
5 bit unsigned integer
Shift amount specified in
bottom byte of Rs
Figure 9: ARM Shift Operations
Instruction specified shift amount
When the shift amount is specified in the instruction, it is contained in a 5 bit field which may take any value
from 0 to 31. A logical shift left (LSL) takes the contents of Rm and moves each bit by the specified amount
to a more significant position. The least significant bits of the result are filled with zeros, and the high bits
of Rm which do not map into the result are discarded, except that the least significant discarded bit becomes
the shifter carry output which may be latched into the C bit of the CPSR when the ALU operation is in the
logical class (see above). For example, the effect of LSL #5 is shown in Figure 10: Logical Shift Left.
31
27 26
0
contents of Rm
carry out
value of operand 2
0 0 0 0 0
Figure 10: Logical Shift Left
Note that LSL #0 is a special case, where the shifter carry out is the old value of the CPSR C flag. The
contents of Rm are used directly as the second operand.
A logical shift right (LSR) is similar, but the contents of Rm are moved to less significant positions in the
result. LSR #5 has the effect shown in Figure 11: Logical Shift Right.
25
P60ARM-B
31
5
4
0
contents of Rm
carry out
0 0 0 0 0
value of operand 2
Figure 11: Logical Shift Right
The form of the shift field which might be expected to correspond to LSR #0 is used to encode LSR #32,
which has a zero result with bit 31 of Rm as the carry output. Logical shift right zero is redundant as it is
the same as logical shift left zero, so the assembler will convert LSR #0 (and ASR #0 and ROR #0) into LSL
#0, and allow LSR #32 to be specified.
An arithmetic shift right (ASR) is similar to logical shift right, except that the high bits are filled with bit 31
of Rm instead of zeros. This preserves the sign in 2's complement notation. For example, ASR #5 is shown
in Figure 12: Arithmetic Shift Right.
31 30
5
4
0
contents of Rm
carry out
value of operand 2
Figure 12: Arithmetic Shift Right
The form of the shift field which might be expected to give ASR #0 is used to encode ASR #32. Bit 31 of Rm
is again used as the carry output, and each bit of operand 2 is also equal to bit 31 of Rm. The result is
therefore all ones or all zeros, according to the value of bit 31 of Rm.
Rotate right (ROR) operations reuse the bits which 'overshoot' in a logical shift right operation by
reintroducing them at the high end of the result, in place of the zeros used to fill the high end in logical right
operations. For example, ROR #5 is shown in Figure 13: Rotate Right.
26
Instruction Set - Shifts
31
5 4
0
contents of Rm
carry out
value of operand 2
Figure 13: Rotate Right
The form of the shift field which might be expected to give ROR #0 is used to encode a special function of
the barrel shifter, rotate right extended (RRX). This is a rotate right by one bit position of the 33 bit quantity
formed by appending the CPSR C flag to the most significant end of the contents of Rm as shown in Figure
14: Rotate Right Extended.
31
1
0
contents of Rm
carry
out
C
in
value of operand 2
Figure 14: Rotate Right Extended
Register specified shift amount
Only the least significant byte of the contents of Rs is used to determine the shift amount. Rs can be any
general register other than R15.
If this byte is zero, the unchanged contents of Rm will be used as the second operand, and the old value of
the CPSR C flag will be passed on as the shifter carry output.
If the byte has a value between 1 and 31, the shifted result will exactly match that of an instruction specified
shift with the same value and shift operation.
If the value in the byte is 32 or more, the result will be a logical extension of the shift described above:
(1)
LSL by 32 has result zero, carry out equal to bit 0 of Rm.
(2)
LSL by more than 32 has result zero, carry out zero.
(3)
LSR by 32 has result zero, carry out equal to bit 31 of Rm.
(4)
LSR by more than 32 has result zero, carry out zero.
27
P60ARM-B
(5)
ASR by 32 or more has result filled with and carry out equal to bit 31 of Rm.
(6)
ROR by 32 has result equal to Rm, carry out equal to bit 31 of Rm.
(7)
ROR by n where n is greater than 32 will give the same result and carry out as ROR by n-32;
therefore repeatedly subtract 32 from n until the amount is in the range 1 to 32 and see above.
Note that the zero in bit 7 of an instruction with a register controlled shift is compulsory; a one in this bit
will cause the instruction to be a multiply or undefined instruction.
4.4.3 Immediate operand rotates
The immediate operand rotate field is a 4 bit unsigned integer which specifies a shift operation on the 8 bit
immediate value. This value is zero extended to 32 bits, and then subject to a rotate right by twice the value
in the rotate field. This enables many common constants to be generated, for example all powers of 2.
4.4.4 Writing to R15
When Rd is a register other than R15, the condition code flags in the CPSR may be updated from the ALU
flags as described above.
When Rd is R15 and the S flag in the instruction is not set the result of the operation is placed in R15 and
the CPSR is unaffected.
When Rd is R15 and the S flag is set the result of the operation is placed in R15 and the SPSR corresponding
to the current mode is moved to the CPSR. This allows state changes which atomically restore both PC and
CPSR. This form of instruction shall not be used in User mode.
4.4.5 Using R15 as an operand
If R15 (the PC) is used as an operand in a data processing instruction the register is used directly.
The PC value will be the address of the instruction, plus 8 or 12 bytes due to instruction prefetching. If the
shift amount is specified in the instruction, the PC will be 8 bytes ahead. If a register is used to specify the
shift amount the PC will be 12 bytes ahead.
4.4.6 TEQ, TST, CMP & CMN opcodes
These instructions do not write the result of their operation but do set flags in the CPSR. An assembler shall
always set the S flag for these instructions even if it is not specified in the mnemonic.
The TEQP form of the instruction used in earlier processors shall not be used in the 32 bit modes, the PSR
transfer operations should be used instead. If used in these modes, its effect is to move SPSR_<mode> to
CPSR if the processor is in a privileged mode and to do nothing if in User mode.
4.4.7 Instruction Cycle Times
Data Processing instructions vary in the number of incremental cycles taken as follows:
28
Normal Data Processing
1S
Data Processing with register specified shift
1S + 1I
Instruction Set - TEQ, TST, CMP & CMN
Data Processing with PC written
2S + 1N
Data Processing with register secified shift and PC written
2S +1N + 1I
S, I and N are as defined in section 5.1 Cycle types on page 65.
4.4.8 Assembler syntax
(1)
MOV,MVN - single operand instructions
<opcode>{cond}{S} Rd,<Op2>
(2)
CMP,CMN,TEQ,TST - instructions which do not produce a result.
<opcode>{cond} Rn,<Op2>
(3)
AND,EOR,SUB,RSB,ADD,ADC,SBC,RSC,ORR,BIC
<opcode>{cond}{S} Rd,Rn,<Op2>
where <Op2> is Rm{,<shift>} or,<#expression>
{cond} - two-character condition mnemonic, see Figure 6: Condition Codes
{S} - set condition codes if S present (implied for CMP, CMN, TEQ, TST).
Rd, Rn and Rm are expressions evaluating to a register number.
If <#expression> is used, the assembler will attempt to generate a shifted immediate 8-bit field to match the
expression. If this is impossible, it will give an error.
<shift> is <shiftname> <register> or <shiftname> #expression, or RRX (rotate right one bit with extend).
<shiftname>s are: ASL, LSL, LSR, ASR, ROR. (ASL is a synonym for LSL, they assemble to the same code.)
4.4.9 Examples
ADDEQ
R2,R4,R5
; if the Z flag is set make R2:=R4+R5
TEQS
R4,#3
; test R4 for equality with 3
; (the S is in fact redundant as the
; assembler inserts it automatically)
SUB
R4,R5,R7,LSR R2
; logical right shift R7 by the number in
; the bottom byte of R2, subtract result
; from R5, and put the answer into R4
MOV
PC,R14
; return from subroutine
MOVS
PC,R14
; return from exception and restore CPSR
from SPSR_mode
29
P60ARM-B
4.5 PSR Transfer (MRS, MSR)
The instruction is only executed if the condition is true. The various conditions are defined at the beginning
of this chapter.
The MRS and MSR instructions are formed from a subset of the Data Processing operations and are
implemented using the TEQ, TST, CMN and CMP instructions without the S flag set. The encoding is
shown in Figure 15: PSR Transfer.
These instructions allow access to the CPSR and SPSR registers. The MRS instruction allows the contents of
the CPSR or SPSR_<mode> to be moved to a general register. The MSR instruction allows the contents of a
general register to be moved to the CPSR or SPSR_<mode> register.
The MSR instruction also allows an immediate value or register contents to be transferred to the condition
code flags (N,Z,C and V) of CPSR or SPSR_<mode> without affecting the control bits. In this case, the top
four bits of the specified register contents or 32 bit immediate value are written to the top four bits of the
relevant PSR.
4.5.1 Operand restrictions
In User mode, the control bits of the CPSR are protected from change, so only the condition code flags of
the CPSR can be changed. In other (privileged) modes the entire CPSR can be changed.
The SPSR register which is accessed depends on the mode at the time of execution. For example, only
SPSR_fiq is accessible when the processor is in FIQ mode.
R15 shall not be specified as the source or destination register.
A further restriction is that no attempt shall be made to access an SPSR in User mode, since no such register
exists.
30
Instruction Set - MRS, MSR
MRS
(transfer PSR contents to a register)
28 27
31
23 22 21
00010
Cond
Ps
16 15
001111
12 11
0
Rd
000000000000
Destination register
Source PSR
0 = CPSR
1 = SPSR_<current mode>
Condition field
MSR (transfer register contents to PSR)
31
23 22 21
28 27
Cond
Pd
00010
4 3
12 11
1010011111
00000000
0
Rm
Source register
Destination PSR
0 = CPSR
1 = SPSR_<current mode>
Condition field
MSR (transfer register contents or immediate value to PSR flag bits only)
Cond
00
12 11
23 22 21
28 27
31
I
10
Pd
0
Source operand
1010001111
Destination PSR
0 = CPSR
1 = SPSR_<current mode>
Immediate Operand
11
0 = Source operand is a register
4
3
00000000
0
Rm
Source register
11
1 = Source operand is an immediate value
8 7
Rotate
0
Imm
Unsigned 8 bit immediate value
shift applied to Imm
Condition field
Figure 15: PSR Transfer
31
P60ARM-B
4.5.2 Reserved bits
Only eleven bits of the PSR are defined in ARM60 (N,Z,C,V,I,F & M[4:0]); the remaining bits (= PSR[27:8,5])
are reserved for use in future versions of the processor. To ensure the maximum compatibility between
ARM60 programs and future processors, the following rules should be observed:
(1)
The reserved bits shall be preserved when changing the value in a PSR.
(2)
Programs shall not rely on specific values from the reserved bits when checking the PSR status,
since they may read as one or zero in future processors.
A read-modify-write strategy should therefore be used when altering the control bits of any PSR register;
this involves transferring the appropriate PSR register to a general register using the MRS instruction,
changing only the relevant bits and then transferring the modified value back to the PSR register using the
MSR instruction.
e.g. The following sequence performs a mode change:
MRS
BIC
ORR
MSR
R0,CPSR
R0,R0,#0x1F
R0,R0,#new_mode
CPSR,R0
;
;
;
;
take a copy of the CPSR
clear the mode bits
select new mode
write back the modified CPSR
When the aim is simply to change the condition code flags in a PSR, an immediate value can be written
directly to the flag bits without disturbing the control bits. e.g. The following instruction sets the N,Z,C &
V flags:
MSR
CPSR_flg,#0xF0000000 ; set all the flags regardless of
; their previous state (does not
; affect any control bits)
No attempt shall be made to write an 8 bit immediate value into the whole PSR since such an operation
cannot preserve the reserved bits.
4.5.3 Instruction Cycle Times
PSR Transfers take 1S incremental cycles, where S is as defined in section 5.1 Cycle types on page 65.
4.5.4 Assembler syntax
(1)
MRS - transfer PSR contents to a register
MRS{cond} Rd,<psr>
(2)
MSR - transfer register contents to PSR
MSR{cond} <psr>,Rm
(3)
MSR - transfer register contents to PSR flag bits only
MSR{cond} <psrf>,Rm
The most significant four bits of the register contents are written to the N,Z,C & V flags respectively.
32
Instruction Set - MRS, MSR
(4)
MSR - transfer immediate value to PSR flag bits only
MSR{cond} <psrf>,<#expression>
The expression should symbolise a 32 bit value of which the most significant four bits are written
to the N,Z,C & V flags respectively.
{cond} - two-character condition mnemonic, see Figure 6: Condition Codes
Rd and Rm are expressions evaluating to a register number other than R15
<psr> is CPSR, CPSR_all, SPSR or SPSR_all. (CPSR and CPSR_all are synonyms as are SPSR and SPSR_all)
<psrf> is CPSR_flg or SPSR_flg
Where <#expression> is used, the assembler will attempt to generate a shifted immediate 8-bit field to
match the expression. If this is impossible, it will give an error.
4.5.5 Examples
In User mode the instructions behave as follows:
MSR
MSR
CPSR_all,Rm
CPSR_flg,Rm
; CPSR[31:28] <- Rm[31:28]
; CPSR[31:28] <- Rm[31:28]
MSR
CPSR_flg,#0xA0000000 ; CPSR[31:28] <- 0xA
;
(i.e. set N,C; clear Z,V)
MRS
Rd,CPSR
; Rd[31:0] <- CPSR[31:0]
In privileged modes the instructions behave as follows:
MSR
MSR
CPSR_all,Rm
CPSR_flg,Rm
; CPSR[31:0] <- Rm[31:0]
; CPSR[31:28] <- Rm[31:28]
MSR
CPSR_flg,#0x50000000 ; CPSR[31:28] <- 0x5
;
(i.e. set Z,V; clear N,C)
MRS
Rd,CPSR
; Rd[31:0] <- CPSR[31:0]
MSR
MSR
SPSR_all,Rm
SPSR_flg,Rm
; SPSR_<mode>[31:0] <- Rm[31:0]
; SPSR_<mode>[31:28] <- Rm[31:28]
MSR
SPSR_flg,#0xC0000000 ; SPSR_<mode>[31:28] <- 0xC
;
(i.e. set N,Z; clear C,V)
MRS
Rd,SPSR
; Rd[31:0] <- SPSR_<mode>[31:0]
33
P60ARM-B
4.6 Multiply and Multiply-Accumulate (MUL, MLA)
The instruction is only executed if the condition is true. The various conditions are defined at the beginning
of this chapter. The instruction encoding is shown in Figure 16: Multiply Instructions.
The multiply and multiply-accumulate instructions use a 2 bit Booth's algorithm to perform integer
multiplication. They give the least significant 32 bits of the product of two 32 bit operands, and may be used
to synthesize higher precision multiplications.
31
28 27
Cond
22 21 20 19
0 0 0 0 0 0 A S
16 15
Rd
12 11
Rn
8
Rs
7
4
1 0 0
1
3
0
Rm
Operand registers
Destination register
Set condition code
0 = do not alter condition codes
1 = set condition codes
Accumulate
0 = multiply only
1 = multiply and accumulate
Condition Field
Figure 16: Multiply Instructions
The multiply form of the instruction gives Rd:=Rm*Rs. Rn is ignored, and should be set to zero for
compatibility with possible future upgrades to the instruction set.
The multiply-accumulate form gives Rd:=Rm*Rs+Rn, which can save an explicit ADD instruction in some
circumstances.
Both forms of the instruction work on operands which may be considered as signed (2's complement) or
unsigned integers.
4.6.1 Operand restrictions
Due to the way multiplication is implemented, certain combinations of operand registers should be
avoided. (The assembler will issue a warning if these restrictions are overlooked.)
The destination register (Rd) should not be the same as the Rm operand register, as Rd is used to hold
intermediate values and Rm is used repeatedly during the multiply. A MUL will give a zero result if
Rm=Rd, and a MLA will give a meaningless result. R15 shall not be used as an operand or as the destination
register.
All other register combinations will give correct results, and Rd, Rn and Rs may use the same register when
required.
34
Instruction Set - MUL, MLA
4.6.2 CPSR ßags
Setting the CPSR flags is optional, and is controlled by the S bit in the instruction. The N (Negative) and Z
(Zero) flags are set correctly on the result (N is made equal to bit 31 of the result, and Z is set if and only if
the result is zero). The C (Carry) flag is set to a meaningless value and the V (oVerflow) flag is unaffected.
4.6.3 Instruction Cycle Times
The Multiply instructions take 1S + mI incremental cycles to execute, where S and I are as defined in section
5.1 Cycle types on page 65.
m
is the number of cycles required by the multiply algorithm, which is determined by the contents of
Rs. Multiplication by any number between 2^(2m-3) and 2^(2m-1)-1 takes 1S+mI m cycles for
1<m>16. Multiplication by 0 or 1 takes 1S+1I cycles, and multiplication by any number greater than
or equal to 2^(29) takes 1S+16I cycles. The maximum time for any multiply is thus 1S+16I cycles.
4.6.4 Assembler syntax
MUL{cond}{S} Rd,Rm,Rs
MLA{cond}{S} Rd,Rm,Rs,Rn
{cond} - two-character condition mnemonic, see Figure 6: Condition Codes
{S}
- set condition codes if S present
Rd, Rm, Rs and Rn are expressions evaluating to a register number other than R15.
4.6.5 Examples
MUL
MLAEQS
R1,R2,R3
R1,R2,R3,R4
; R1:=R2*R3
; conditionally R1:=R2*R3+R4,
; setting condition codes
35
P60ARM-B
4.7 Single data transfer (LDR, STR)
The instruction is only executed if the condition is true. The various conditions are defined at the beginning
of this chapter. The instruction encoding is shown in Figure 17: Single Data Transfer Instructions.
The single data transfer instructions are used to load or store single bytes or words of data. The memory
address used in the transfer is calculated by adding an offset to or subtracting an offset from a base register.
The result of this calculation may be written back into the base register if `auto-indexing' is required.
31
28 27 26 25 24 23 22 21 20 19
Cond
01
I P U B W L
16 15
Rn
12 11
0
Rd
Offset
Source/Destination register
Base register
Load/Store bit
0 = Store to memory
1 = Load from memory
Write-back bit
0 = no write-back
1 = write address into base
Byte/Word bit
0 = transfer word quantity
1 = transfer byte quantity
Up/Down bit
0 = down; subtract offset from base
1 = up; add offset to base
Pre/Post indexing bit
0 = post; add offset after transfer
1 = pre; add offset before transfer
Immediate offset
11
0 = offset is an immediate value
0
Immediate offset
Unsigned 12 bit immediate offset
11
1 = offset is a register
Shift
shift applied to Rm
Condition field
Figure 17: Single Data Transfer Instructions
36
4
3
0
Rm
Offset register
Instruction Set - LDR, STR
4.7.1 Offsets and auto-indexing
The offset from the base may be either a 12 bit unsigned binary immediate value in the instruction, or a
second register (possibly shifted in some way). The offset may be added to (U=1) or subtracted from (U=0)
the base register Rn. The offset modification may be performed either before (pre-indexed, P=1) or after
(post-indexed, P=0) the base is used as the transfer address.
The W bit gives optional auto increment and decrement addressing modes. The modified base value may
be written back into the base (W=1), or the old base value may be kept (W=0). In the case of post-indexed
addressing, the write back bit is redundant and is always set to zero, since the old base value can be retained
by setting the offset to zero. Therefore post-indexed data transfers always write back the modified base. The
only use of the W bit in a post-indexed data transfer is in privileged mode code, where setting the W bit
forces non-privileged mode for the transfer, allowing the operating system to generate a user address in a
system where the memory management hardware makes suitable use of this hardware.
4.7.2 Shifted register offset
The 8 shift control bits are described in the data processing instructions section. However, the register
specified shift amounts are not available in this instruction class. See 4.4.2 Shifts.
4.7.3 Bytes and words
This instruction class may be used to transfer a byte (B=1) or a word (B=0) between an ARM60 register and
memory.
The action of LDR(B) and STR(B) instructions is influenced by the BIGEND control signal. The two possible
configurations are described below.
Little Endian Configuration
A byte load (LDRB) expects the data on data bus inputs 7 through 0 if the supplied address is on a word
boundary, on data bus inputs 15 through 8 if it is a word address plus one byte, and so on. The selected byte
is placed in the bottom 8 bits of the destination register, and the remaining bits of the register are filled with
zeros.
A byte store (STRB) repeats the bottom 8 bits of the source register four times across data bus outputs 31
through 0. The external memory system should activate the appropriate byte subsystem to store the data.
A word load (LDR) will normally use a word aligned address. However, an address offset from a word
boundary will cause the data to be rotated into the register so that the addressed byte occupies bits 0 to 7.
This means that half-words accessed at offsets 0 and 2 from the word boundary will be correctly loaded into
bits 0 through 15 of the register. Two shift operations are then required to clear or to sign extend the upper
16 bits.
A word store (STR) should generate a word aligned address. The word presented to the data bus is not
affected if the address is not word aligned. That is, bit 31 of the register being stored always appears on data
bus output 31.
37
P60ARM-B
Big Endian Configuration
A byte load (LDRB) expects the data on data bus inputs 31 through 24 if the supplied address is on a word
boundary, on data bus inputs 23 through 16 if it is a word address plus one byte, and so on. The selected
byte is placed in the bottom 8 bits of the destination register and the remaining bits of the register are filled
with zeros.
A byte store (STRB) repeats the bottom 8 bits of the source register four times across data bus outputs 31
through 0. The external memory system should activate the appropriate byte subsystem to store the data.
A word load (LDR) should generate a word aligned address. An address offset of 0 or 2 from a word
boundary will cause the data to be rotated into the register so that the addressed byte occupies bits 31
through 24. This means that half-words accessed at these offsets will be correctly loaded into bits 16 through
31 of the register. A shift operation is then required to move (and optionally sign extend) the data into the
bottom 16 bits. An address offset of 1 or 3 from a word boundary will cause the data to be rotated into the
register so that the addressed byte occupies bits 15 through 8.
A word store (STR) should generate a word aligned address. The word presented to the data bus is not
affected if the address is not word aligned. That is, bit 31 of the register being stored always appears on data
bus output 31.
4.7.4 Use of R15
Write-back shall not be specified if R15 is specified as the base register (Rn). When using R15 as the base
register you must remember it contains an address 8 bytes on from the address of the current instruction.
R15 shall not be specified as the register offset (Rm).
When R15 is the source register (Rd) of a register store (STR) instruction, the stored value will be address
of the instruction plus 12.
4.7.5 Restriction on the use of base register
When configured for late aborts, the following example code is difficult to unwind as the base register, Rn,
gets updated before the abort handler starts. Sometimes it may be impossible to calculate the initial value.
For example:
LDR
R0,[R1],R1
<LDR|STR> Rd, [Rn],{+/-}Rn{,<shift>}
Therefore a post-indexed LDR|STR where Rm is the same register as Rn shall not be used.
38
Instruction Set - LDR, STR
4.7.6 Data Aborts
A transfer to or from a legal address may cause problems for a memory management system. For instance,
in a system which uses virtual memory the required data may be absent from main memory. The memory
manager can signal a problem by taking the processor ABORT input HIGH whereupon the Data Abort trap
will be taken. It is up to the system software to resolve the cause of the problem, then the instruction can be
restarted and the original program continued.
ARM60 supports two types of Data Abort processing depending on the LATEABT control signal. When set
for Early Aborts, any base register write-back which would have occurred is prevented in the event of an
abort. When configured for Late Aborts, this write-back is allowed to take place and the Abort handler must
correct this before allowing the instruction to be re-executed.
4.7.7 Instruction Cycle Times
Normal LDR instructions take 1S + 1N + 1I and LDR PC take 2S + 2N +1I incremental cycles, where S,N
and I are as defined in section 5.1 Cycle types on page 65.
STR instructions take 2N incremental cycles to execute.
4.7.8 Assembler syntax
<LDR|STR>{cond}{B}{T} Rd,<Address>
LDR - load from memory into a register
STR - store from a register into memory
{cond} - two-character condition mnemonic, see Figure 6: Condition Codes
{B} - if B is present then byte transfer, otherwise word transfer
{T} - if T is present the W bit will be set in a post-indexed instruction, forcing non-privileged mode for the
transfer cycle. T is not allowed when a pre-indexed addressing mode is specified or implied.
Rd is an expression evaluating to a valid register number.
<Address> can be:
(i)
An expression which generates an address:
<expression>
The assembler will attempt to generate an instruction using the PC as a base and a corrected
immediate offset to address the location given by evaluating the expression. This will be a PC
relative, pre-indexed address. If the address is out of range, an error will be generated.
(ii)
A pre-indexed addressing specification:
[Rn] offset of zero
[Rn,<#expression>]{!} offset of <expression> bytes
39
P60ARM-B
[Rn,{+/-}Rm{,<shift>}]{!} offset of +/- contents of index register, shifted by <shift>
(iii)
A post-indexed addressing specification:
[Rn],<#expression> offset of <expression> bytes
[Rn],{+/-}Rm{,<shift>} offset of +/- contents of index register, shifted as by <shift>.
Rn and Rm are expressions evaluating to a register number. If Rn is R15 then the assembler will subtract 8
from the offset value to allow for ARM60 pipelining. In this case base write-back shall not be specified.
<shift> is a general shift operation (see section on data processing instructions) but note that the shift
amount may not be specified by a register.
{!} writes back the base register (set the W bit) if ! is present.
4.7.9 Examples
STR
R1,[R2,R4]!
; store R1 at R2+R4 (both of which are
; registers) and write back address to R2
STR
R1,[R2],R4
; store R1 at R2 and write back
; R2+R4 to R2
LDR
R1,[R2,#16]
; load R1 from contents of R2+16
; Don't write back
LDR
R1,[R2,R3,LSL#2]
; load R1 from contents of R2+R3*4
LDREQB
R1,[R6,#5]
; conditionally load byte at R6+5 into
; R1 bits 0 to 7, filling bits 8 to 31
; with zeros
STR
R1,PLACE
•
•
; generate PC relative offset to address
; PLACE
PLACE
40
Instruction Set - LDM, STM
4.8 Block data transfer (LDM, STM)
The instruction is only executed if the condition is true. The various conditions are defined at the beginning
of this chapter. The instruction encoding is shown in Figure 18: Block Data Transfer Instructions.
Block data transfer instructions are used to load (LDM) or store (STM) any subset of the currently visible
registers. They support all possible stacking modes, maintaining full or empty stacks which can grow up or
down memory, and are very efficient instructions for saving or restoring context, or for moving large blocks
of data around main memory.
4.8.1 The register list
The instruction can cause the transfer of any registers in the current bank (and non-user mode programs
can also transfer to and from the user bank, see below). The register list is a 16 bit field in the instruction,
with each bit corresponding to a register. A 1 in bit 0 of the register field will cause R0 to be transferred, a
0 will cause it not to be transferred; similarly bit 1 controls the transfer of R1, and so on.
Any subset of the registers, or all the registers, may be specified. The only restriction is that the register list
should not be empty.
Whenever R15 is stored to memory the stored value is the address of the STM instruction plus 12.
31
28 27
Cond
25 24 23 22 21 20 19
100
P U S W L
16 15
Rn
0
Register list
Base register
Load/Store bit
0 = Store to memory
1 = Load from memory
Write-back bit
0 = no write-back
1 = write address into base
PSR & force user bit
0 = do not load PSR or force user mode
1 = load PSR or force user mode
Up/Down bit
0 = down; subtract offset from base
1 = up; add offset to base
Pre/Post indexing bit
0 = post; add offset after transfer
1 = pre; add offset before transfer
Condition field
Figure 18: Block Data Transfer Instructions
4.8.2 Addressing modes
The transfer addresses are determined by the contents of the base register (Rn), the pre/post bit (P) and the
up/down bit (U). The registers are transferred in the order lowest to highest, so R15 (if in the list) will
always be transferred last. The lowest register also gets transferred to/from the lowest memory address. By
way of illustration, consider the transfer of R1, R5 and R7 in the case where Rn=0x1000 and write back of
41
P60ARM-B
the modified base is required (W=1). Figure 19: Post-increment addressing, Figure 20: Pre-increment addressing,
Figure 21: Post-decrement addressing and Figure 22: Pre-decrement addressing show the sequence of register
transfers, the addresses used, and the value of Rn after the instruction has completed.
In all cases, had write back of the modified base not been required (W=0), Rn would have retained its initial
value of 0x1000 unless it was also in the transfer list of a load multiple register instruction, when it would
have been overwritten with the loaded value.
4.8.3 Address Alignment
The address should normally be a word aligned quantity and non-word aligned addresses do not affect the
instruction. However, the bottom 2 bits of the address will appear on A[1:0] and might be interpreted by
the memory system.
0x100C
Rn
0x100C
0x1000
R1
0x0FF4
0x0FF4
1
2
0x100C
R5
R1
0x1000
Rn
0x100C
R7
R5
R1
0x0FF4
3
0x1000
0x0FF4
4
Figure 19: Post-increment addressing
42
0x1000
Instruction Set - LDM, STM
0x100C
0x100C
R1
Rn
0x1000
0x1000
0x0FF4
0x0FF4
1
2
0x100C
Rn
R5
R1
R7
R5
R1
0x100C
0x1000
0x1000
0x0FF4
0x0FF4
3
4
Figure 20: Pre-increment addressing
Rn
0x100C
0x100C
0x1000
0x1000
R1
0x0FF4
0x0FF4
1
2
0x100C
0x100C
0x1000
R7
R5
R1
R5
R1
0x0FF4
3
0x1000
0x0FF4
Rn
4
Figure 21: Post-decrement addressing
43
P60ARM-B
Rn
0x100C
0x100C
0x1000
0x1000
0x0FF4
R1
1
R5
R1
0x0FF4
2
0x100C
0x100C
0x1000
0x1000
0x0FF4
Rn
R7
R5
R1
3
0x0FF4
4
Figure 22: Pre-decrement addressing
4.8.4 Use of the S bit
When the S bit is set in a LDM/STM instruction its meaning depends on whether or not R15 is in the transfer
list and on the type of instruction. The S bit should only be set if the instruction is to execute in a privileged
mode.
LDM with R15 in transfer list and S bit set (Mode changes)
If the instruction is a LDM then SPSR_<mode> is transferred to CPSR at the same time as R15 is loaded.
STM with R15 in transfer list and S bit set (User bank transfer)
The registers transferred are taken from the User bank rather than the bank corresponding to the current
mode. This is useful for saving the user state on process switches. Base write-back shall not be used when
this mechanism is employed.
R15 not in list and S bit set (User bank transfer)
For both LDM and STM instructions, the User bank registers are transferred rather than the register bank
corresponding to the current mode. This is useful for saving the user state on process switches. Base writeback shall not be used when this mechanism is employed.
When the instruction is LDM, care must be taken not to read from a banked register during the following
cycle (inserting a NOP after the LDM will ensure safety).
44
Instruction Set - LDM, STM
4.8.5 Use of R15 as the base
R15 shall not be used as the base register in any LDM or STM instruction.
4.8.6 Inclusion of the base in the register list
When write-back is specified, the base is written back at the end of the second cycle of the instruction.
During a STM, the first register is written out at the start of the second cycle. A STM which includes storing
the base, with the base as the first register to be stored, will therefore store the unchanged value, whereas
with the base second or later in the transfer order, will store the modified value. A LDM will always
overwrite the updated base if the base is in the list.
4.8.7 Data Aborts
Some legal addresses may be unacceptable to a memory management system, and the memory manager
can indicate a problem with an address by taking the ABORT signal HIGH. This can happen on any
transfer during a multiple register load or store, and must be recoverable if ARM60 is to be used in a virtual
memory system.
The state of the LATEABT control signal does not affect the behaviour of LDM and STM instructions in the
event of a memory abort exception.
Aborts during STM instructions
If the abort occurs during a store multiple instruction, ARM60 takes little action until the instruction
completes, whereupon it enters the data abort trap. The memory manager is responsible for preventing
erroneous writes to the memory. The only change to the internal state of the processor will be the
modification of the base register if write-back was specified, and this must be reversed by software (and the
cause of the abort resolved) before the instruction may be retried.
Aborts during LDM instructions
When ARM60 detects a data abort during a load multiple instruction, it modifies the operation of the
instruction to ensure that recovery is possible.
(i)
Overwriting of registers stops when the abort happens. The aborting load will not take place but
earlier ones may have overwritten registers. The PC is always the last register to be written and so
will always be preserved.
(ii)
The base register is restored, to its modified value if write-back was requested. This ensures
recoverability in the case where the base register is also in the transfer list, and may have been
overwritten before the abort occurred.
The data abort trap is taken when the load multiple has completed, and the system software must undo any
base modification (and resolve the cause of the abort) before restarting the instruction.
4.8.8 Instruction Cycle Times
Normal LDM instructions take nS + 1N + 1I and LDM PC takes (n+1)S + 2N + 1I incremental cycles, where
S,N and I are as defined in section 5.1 Cycle types on page 65.
45
P60ARM-B
STM instructions take (n-1)S + 2N incremental cycles to execute.
n
is the number of words transferred.
4.8.9 Assembler syntax
<LDM|STM>{cond}<FD|ED|FA|EA|IA|IB|DA|DB> Rn{!},<Rlist>{^}
{cond} - two character condition mnemonic, see Figure 6: Condition Codes
Rn is an expression evaluating to a valid register number
<Rlist> is a list of registers and register ranges enclosed in {} (eg {R0,R2-R7,R10}).
{!} if present requests write-back (W=1), otherwise W=0
{^} if present set S bit to load the CPSR along with the PC, or force transfer of user bank when in privileged
mode
Addressing mode names
There are different assembler mnemonics for each of the addressing modes, depending on whether the
instruction is being used to support stacks or for other purposes. The equivalences between the names and
the values of the bits in the instruction are shown in the following table:
name
stack
other
L bit
P bit
U bit
pre-increment load
LDMED
LDMIB
1
1
1
post-increment load
LDMFD
LDMIA
1
0
1
pre-decrement load
LDMEA
LDMDB
1
1
0
post-decrement load
LDMFA
LDMDA
1
0
0
pre-increment store
STMFA
STMIB
0
1
1
post-increment store
STMEA
STMIA
0
0
1
pre-decrement store
STMFD
STMDB
0
1
0
post-decrement store
STMED
STMDA
0
0
0
Table 5: Addressing Mode Names
FD, ED, FA, EA define pre/post indexing and the up/down bit by reference to the form of stack required.
The F and E refer to a ÒfullÓ or ÒemptyÓ stack, i.e. whether a pre-index has to be done (full) before storing
to the stack. The A and D refer to whether the stack is ascending or descending. If ascending, a STM will go
up and LDM down, if descending, vice-versa.
46
Instruction Set - LDM, STM
IA, IB, DA, DB allow control when LDM/STM are not being used for stacks and simply mean Increment
After, Increment Before, Decrement After, Decrement Before.
4.8.10 Examples
LDMFD
SP!,{R0,R1,R2}
; unstack 3 registers
STMIA
R0,{R0-R15}
; save all registers
LDMFD
LDMFD
SP!,{R15}
SP!,{R15}^
STMFD
R13,{R0-R14}^
; R15 <- (SP),CPSR unchanged
; R15 <- (SP), CPSR <- SPSR_mode (allowed
; only in privileged modes)
; Save user mode regs on stack (allowed
; only in privileged modes)
These instructions may be used to save state on subroutine entry, and restore it efficiently on return to the
calling routine:
STMED
SP!,{R0-R3,R14}
; save R0 to R3 to use as workspace
; and R14 for returning
BL
somewhere
; this nested call will overwrite R14
LDMED
SP!,{R0-R3,R15}
; restore workspace and return
47
P60ARM-B
4.9 Single data swap (SWP)
The instruction is only executed if the condition is true. The various conditions are defined at the beginning
of this chapter. The instruction encoding is shown in Figure 23: Swap Instruction.
The data swap instruction is used to swap a byte or word quantity between a register and external memory.
This instruction is implemented as a memory read followed by a memory write which are ÒlockedÓ
together (the processor cannot be interrupted until both operations have completed, and the memory
manager is warned to treat them as inseparable). This class of instruction is particularly useful for
implementing software semaphores. )
31
28 27
Cond
23 22 21 20 19
00010
B
00
16 15
Rn
12 11
Rd
8 7
0000
4
1001
3
0
Rm
Source register
Destination register
Base register
Byte/Word bit
0 = swap word quantity
1 = swap byte quantity
Condition field
Figure 23: Swap Instruction
The swap address is determined by the contents of the base register (Rn). The processor first reads the
contents of the swap address. Then it writes the contents of the source register (Rm) to the swap address,
and stores the old memory contents in the destination register (Rd). The same register may be specified as
both the source and destination.
The LOCK output goes HIGH for the duration of the read and write operations to signal to the external
memory manager that they are locked together, and should be allowed to complete without interruption.
This is important in multi-processor systems where the swap instruction is the only indivisible instruction
which may be used to implement semaphores; control of the memory must not be removed from a
processor while it is performing a locked operation.
4.9.1 Bytes and words
This instruction class may be used to swap a byte (B=1) or a word (B=0) between an ARM60 register and
memory. The SWP instruction is implemented as a LDR followed by a STR and the action of these is as
described in the section on single data transfers. In particular, the description of Big and Little Endian
configuration applies to the SWP instruction.
4.9.2 Use of R15
R15 shall not be used as an operand (Rd, Rn or Rs) in a SWP instruction.
48
Instruction Set - SWP
4.9.3 Data Aborts
If the address used for the swap is unacceptable to a memory management system, the internal MMU or
external memory manager can flag the problem by driving ABORT HIGH. This can happen on either the
read or the write cycle (or both), and in either case, the Data Abort trap will be taken. It is up to the system
software to resolve the cause of the problem, then the instruction can be restarted and the original program
continued.
Because no base register write-back is allowed, the behaviour of an aborted SWP instruction is the same
regardless of the state of the LATEABT control signal.
4.9.4 Instruction Cycle Times
Swap instructions take 1S + 2N +1I incremental cycles to execute, where S,N and I are as defined in section
5.1 Cycle types on page 65.
4.9.5 Assembler syntax
<SWP>{cond}{B} Rd,Rm,[Rn]
{cond} - two-character condition mnemonic, see Figure 6: Condition Codes
{B} - if B is present then byte transfer, otherwise word transfer
Rd,Rm,Rn are expressions evaluating to valid register numbers
4.9.6 Examples
SWP
R0,R1,[R2]
; load R0 with the contents of R2, and
; store R1 at R2
SWPB
R2,R3,[R4]
; load R2 with the byte at R4, and
; store bits 0 to 7 of R3 at R4
SWPEQ
R0,R0,[R1]
; conditionally swap the contents of R1
; with R0
49
P60ARM-B
4.10 Software interrupt (SWI)
The instruction is only executed if the condition is true. The various conditions are defined at the beginning
of this chapter. The instruction encoding is shown in Figure 24: Software Interrupt Instruction.
The software interrupt instruction is used to enter Supervisor mode in a controlled manner. The instruction
causes the software interrupt trap to be taken, which effects the mode change. The PC is then forced to a
fixed value (0x08) and the CPSR is saved in SPSR_svc. If the SWI vector address is suitably protected (by
external memory management hardware) from modification by the user, a fully protected operating system
may be constructed.
31
28 27
Cond
24 23
0
1111
Comment field (ignored by Processor)
Condition field
Figure 24: Software Interrupt Instruction
4.10.1 Return from the supervisor
The PC is saved in R14_svc upon entering the software interrupt trap, with the PC adjusted to point to the
word after the SWI instruction. MOVS PC,R14_svc will return to the calling program and restore the CPSR.
Note that the link mechanism is not re-entrant, so if the supervisor code wishes to use software interrupts
within itself it must first save a copy of the return address and SPSR.
4.10.2 Comment Þeld
The bottom 24 bits of the instruction are ignored by the processor, and may be used to communicate
information to the supervisor code. For instance, the supervisor may look at this field and use it to index
into an array of entry points for routines which perform the various supervisor functions.
4.10.3 Instruction Cycle Times
Software interrupt instructions take 2S + 1N incremental cycles to execute, where S and N are as defined
in section 5.1 Cycle types on page 65.
4.10.4 Assembler syntax
SWI{cond} <expression>
{cond} - two character condition mnemonic, see Figure 6: Condition Codes
<expression> is evaluated and placed in the comment field (which is ignored by ARM60).
50
Instruction Set - SWI
4.10.5 Examples
SWI
SWI
SWINE
ReadC
WriteI+”k”
0
;
;
;
;
get next character from read stream
output a “k” to the write stream
conditionally call supervisor
with 0 in comment field
The above examples assume that suitable supervisor code exists, for instance:
0x08 B Supervisor
; SWI entry point
EntryTable
DCD ZeroRtn
DCD ReadCRtn
DCD WriteIRtn
...
; addresses of supervisor routines
Zero
ReadC
WriteI
EQU
EQU
EQU
0
256
512
Supervisor
; SWI has routine required in bits 8-23 and data (if any) in bits 0-7.
; Assumes R13_svc points to a suitable stack
STMFD
LDR
BIC
MOV
ADR
LDR
R13,{R0-R2,R14}
R0,[R14,#-4]
R0,R0,#0xFF000000
R1,R0,LSR#8
R2,EntryTable
R15,[R2,R1,LSL#2]
WriteIRtn
......
LDMFD
R13,{R0-R2,R15}^
;
;
;
;
;
;
save work registers and return address
get SWI instruction
clear top 8 bits
get routine offset
get start address of entry table
branch to appropriate routine
; enter with character in R0 bits 0-7
; restore workspace and return
; restoring processor mode and flags
51
P60ARM-B
4.11 Coprocessor data operations (CDP)
The instruction is only executed if the condition is true. The various conditions are defined at the beginning
of this chapter. The instruction encoding is shown in Figure 25: Coprocessor Data Operation Instruction.
This class of instruction is used to tell a coprocessor to perform some internal operation. No result is
communicated back to ARM60, and it will not wait for the operation to complete. The coprocessor could
contain a queue of such instructions awaiting execution, and their execution can overlap other ARM60
activity allowing the coprocessor and ARM60 to perform independent tasks in parallel.
31
28 27
Cond
24 23
1110
CP Opc
20 19
16 15
CRn
12 11
CRd
8 7
CP#
5
CP
4
0
3
0
CRm
Coprocessor operand register
Coprocessor information
Coprocessor number
Coprocessor destination register
Coprocessor operand register
Coprocessor operation code
Condition field
Figure 25: Coprocessor Data Operation Instruction
4.11.1 The Coprocessor Þelds
Only bit 4 and bits 24 to 31 are significant to ARM60; the remaining bits are used by coprocessors. The above
field names are used by convention, and particular coprocessors may redefine the use of all fields except
CP# as appropriate. The CP# field is used to contain an identifying number (in the range 0 to 15) for each
coprocessor, and a coprocessor will ignore any instruction which does not contain its number in the CP#
field.
The conventional interpretation of the instruction is that the coprocessor should perform an operation
specified in the CP Opc field (and possibly in the CP field) on the contents of CRn and CRm, and place the
result in CRd.
4.11.2 Instruction Cycle Times
Coprocessor data operations take 1S + bI incremental cycles to execute, where S and I are as defined in
section 5.1 Cycle types on page 65.
b
52
is the number of cycles spent in the coprocessor busy-wait loop.
Instruction Set - CDP
4.11.3 Assembler syntax
CDP{cond} p#,<expression1>,cd,cn,cm{,<expression2>}
{cond} - two character condition mnemonic, see Figure 6: Condition Codes
p# - the unique number of the required coprocessor
<expression1> - evaluated to a constant and placed in the CP Opc field
cd, cn and cm evaluate to the valid coprocessor register numbers CRd, CRn and CRm respectively
<expression2> - where present is evaluated to a constant and placed in the CP field
4.11.4 Examples
CDP
p1,10,c1,c2,c3
; request coproc 1 to do operation 10
; on CR2 and CR3, and put the result in CR1
CDPEQ
p2,5,c1,c2,c3,2
; if Z flag is set request coproc 2 to do
; operation 5 (type 2) on CR2 and CR3,
; and put the result in CR1
53
P60ARM-B
4.12 Coprocessor data transfers (LDC, STC)
The instruction is only executed if the condition is true. The various conditions are defined at the beginning
of this chapter. The instruction encoding is shown in Figure 26: Coprocessor Data Transfer Instructions.
This class of instruction is used to load (LDC) or store (STC) a subset of a coprocessorsÕs registers directly
to memory. ARM60 is responsible for supplying the memory address, and the coprocessor supplies or
accepts the data and controls the number of words transferred.
31
28 27
Cond
25 24 23 22 21 20 19
110
P U N W L
16 15
Rn
12 11
CRd
8 7
CP#
0
Offset
Unsigned 8 bit immediate offset
Coprocessor number
Coprocessor source/destination register
Base register
Load/Store bit
0 = Store to memory
1 = Load from memory
Write-back bit
0 = no write-back
1 = write address into base
Transfer length
Up/Down bit
0 = down; subtract offset from base
1 = up; add offset to base
Pre/Post indexing bit
0 = post; add offset after transfer
1 = pre; add offset before transfer
Condition field
Figure 26: Coprocessor Data Transfer Instructions
4.12.1 The Coprocessor Þelds
The CP# field is used to identify the coprocessor which is required to supply or accept the data, and a
coprocessor will only respond if its number matches the contents of this field.
The CRd field and the N bit contain information for the coprocessor which may be interpreted in different
ways by different coprocessors, but by convention CRd is the register to be transferred (or the first register
where more than one is to be transferred), and the N bit is used to choose one of two transfer length options.
For instance N=0 could select the transfer of a single register, and N=1 could select the transfer of all the
registers for context switching.
54
Instruction Set - LDC, STC
4.12.2 Addressing modes
ARM60 is responsible for providing the address used by the memory system for the transfer, and the
addressing modes available are a subset of those used in single data transfer instructions. Note, however,
that the immediate offsets are 8 bits wide and specify word offsets for coprocessor data transfers, whereas
they are 12 bits wide and specify byte offsets for single data transfers.
The 8 bit unsigned immediate offset is shifted left 2 bits and either added to (U=1) or subtracted from (U=0)
the base register (Rn); this calculation may be performed either before (P=1) or after (P=0) the base is used
as the transfer address. The modified base value may be overwritten back into the base register (if W=1), or
the old value of the base may be preserved (W=0). Note that post-indexed addressing modes require
explicit setting of the W bit, unlike LDR and STR which always write-back when post-indexed.
The value of the base register, modified by the offset in a pre-indexed instruction, is used as the address for
the transfer of the first word. The second word (if more than one is transferred) will go to or come from an
address one word (4 bytes) higher than the first transfer, and the address will be incremented by one word
for each subsequent transfer.
4.12.3 Address Alignment
The base address should normally be a word aligned quantity. The bottom 2 bits of the address will appear
on A[1:0] and might be interpreted by the memory system.
4.12.4 Use of R15
If Rn is R15, the value used will be the address of the instruction plus 8 bytes. Base write-back to R15 shall
not be specified.
4.12.5 Data aborts
If the address is legal but the memory manager generates an abort, the data trap will be taken. The writeback of the modified base will take place, but all other processor state will be preserved. The coprocessor is
partly responsible for ensuring that the data transfer can be restarted after the cause of the abort has been
resolved, and must ensure that any subsequent actions it undertakes can be repeated when the instruction
is retried.
The state of the LATEABT control signal does not affect the behaviour of LDC and STC instructions in the
event of an Abort exception.
4.12.6 Instruction Cycle Times
Coprocessor data transfer instructions take (n-1)S + 2N + bI incremental cycles to execute, where S, N and
I are as defined in section 5.1 Cycle types on page 65.
n
is the number of words transferred.
b
is the number of cycles spent in the coprocessor busy-wait loop.
4.12.7 Assembler syntax
<LDC|STC>{cond}{L} p#,cd,<Address>
55
P60ARM-B
LDC - load from memory to coprocessor
STC - store from coprocessor to memory
{L} - when present perform long transfer (N=1), otherwise perform short transfer (N=0)
{cond} - two character condition mnemonic, see Figure 6: Condition Codes
p# - the unique number of the required coprocessor
cd is an expression evaluating to a valid coprocessor register number that is placed in the CRd field
<Address> can be:
(i)
An expression which generates an address:
<expression>
The assembler will attempt to generate an instruction using the PC as a base and a corrected
immediate offset to address the location given by evaluating the expression. This will be a PC
relative, pre-indexed address. If the address is out of range, an error will be generated.
(ii)
A pre-indexed addressing specification:
[Rn] offset of zero
[Rn,<#expression>]{!} offset of <expression> bytes
(iii)
A post-indexed addressing specification:
[Rn],<#expression> offset of <expression> bytes
Rn is an expression evaluating to a valid ARM60 register number. Note, if Rn is R15 then the assembler will
subtract 8 from the offset value to allow for ARM60 pipelining.
{!} write back the base register (set the W bit) if ! is present
4.12.8 Examples
LDC
p1,c2,table
STCEQL
p2,c3,[R5,#24]!
;
;
;
;
;
;
load c2 of coproc 1 from address table,
using a PC relative address.
conditionally store c3 of coproc 2 into
an address 24 bytes up from R5, write this
address back to R5, and use long transfer
option (probably to store multiple words)
Note that though the address offset is expressed in bytes, the instruction offset field is in words. The
assembler will adjust the offset appropriately.
56
Instruction Set - MRC, MCR
4.13 Coprocessor register transfers (MRC, MCR)
The is only executed if the condition is true. The various conditions are defined at the beginning of this
chapter. The instruction encoding is shown in Figure 27: Coprocessor Register Transfer Instructions.
This class of instruction is used to communicate information directly between ARM60 and a coprocessor.
An example of a coprocessor to ARM60 register transfer (MRC) instruction would be a FIX of a floating
point value held in a coprocessor, where the floating point number is converted into a 32 bit integer within
the coprocessor, and the result is then transferred to an ARM60 register. A FLOAT of a 32 bit value in an
ARM60 register into a floating point value within the coprocessor illustrates the use of an ARM60 register
to coprocessor transfer (MCR).
31
28 27
Cond
24 23
1110
21 20 19
CP Opc L
16 15
CRn
12 11
Rd
8 7
CP#
5 4 3
CP
1
0
CRm
Coprocessor operand register
Coprocessor information
Coprocessor number
ARM source/destination register
Coprocessor source/destination register
Load/Store bit
0 = Store to Co-Processor
1 = Load from Co-Processor
Coprocessor operation mode
Condition field
Figure 27: Coprocessor Register Transfer Instructions
An important use of this instruction is to communicate control information directly from the coprocessor
into the ARM60 CPSR flags. As an example, the result of a comparison of two floating point values within
a coprocessor can be moved to the CPSR to control the subsequent flow of execution.
Note for future compatbility the ARM610 has an internal coprocessor (#15) for control of on-chip functions.
Accesses to this coprocessor are performed during coprocessor register transfers.
4.13.1 The Coprocessor Þelds
The CP# field is used, as for all coprocessor instructions, to specify which coprocessor is being called upon.
The CP Opc, CRn, CP and CRm fields are used only by the coprocessor, and the interpretation presented
here is derived from convention only. Other interpretations are allowed where the coprocessor
functionality is incompatible with this one. The conventional interpretation is that the CP Opc and CP fields
57
P60ARM-B
specify the operation the coprocessor is required to perform, CRn is the coprocessor register which is the
source or destination of the transferred information, and CRm is a second coprocessor register which may
be involved in some way which depends on the particular operation specified.
4.13.2 Transfers to R15
When a coprocessor register transfer to ARM60 has R15 as the destination, bits 31, 30, 29 and 28 of the
transferred word are copied into the N, Z, C and V flags respectively. The other bits of the transferred word
are ignored, and the PC and other CPSR bits are unaffected by the transfer.
4.13.3 Transfers from R15
A coprocessor register transfer from ARM60 with R15 as the source register will store the PC+12.
4.13.4 Instruction Cycle Times
MRC instructions take 1S + bI +1C incremental cycles to execute, where S, I and C are as defined in section
5.1 Cycle types on page 65.
MCR instructions take 1S + (b+1)I +1C incremental cycles to execute.
b
is the number of cycles spent in the coprocessor busy-wait loop.
4.13.5 Assembler syntax
<MCR|MRC>{cond} p#,<expression1>,Rd,cn,cm{,<expression2>}
MRC - move from coprocessor to ARM60 register (L=1)
MCR - move from ARM60 register to coprocessor (L=0)
{cond} - two character condition mnemonic, see Figure 6: Condition Codes
p# - the unique number of the required coprocessor
<expression1> - evaluated to a constant and placed in the CP Opc field
Rd is an expression evaluating to a valid ARM60 register number
cn and cm are expressions evaluating to the valid coprocessor register numbers CRn and CRm respectively
<expression2> - where present is evaluated to a constant and placed in the CP field
4.13.6 Examples
58
MRC
2,5,R3,c5,c6
; request coproc 2 to perform operation 5
; on c5 and c6, and transfer the (single
; 32 bit word) result back to R3
MCR
6,0,R4,c6
; request coproc 6 to perform operation 0
; on R4 and place the result in c6
Instruction Set - MRC, MCR
MRCEQ
3,9,R3,c5,c6,2
; conditionally request coproc 3 to perform
; operation 9 (type 2) on c5 and c6, and
; transfer the result back to R3
59
P60ARM-B
4.14 UndeÞned instruction
The instruction is only executed if the condition is true. The various conditions are defined at the beginning
of this chapter. The instruction format is shown in Figure 28: Undefined Instruction.
If the condition is true, the undefined instruction trap will be taken.
31
28 27
Cond
25 24
011
5 4 3
xxxxxxxxxxxxxxxxxxxx
1
0
xxxx
Figure 28: Undefined Instruction
Note that the undefined instruction mechanism involves offering this instruction to any coprocessors which
may be present, and all coprocessors must refuse to accept it by driving CPA and CPB HIGH. For systems
without a coprocessor, CPA and CPB must be driven HIGH at all times.
4.14.1 Assembler syntax
At present the assembler has no mnemonics for generating this instruction. If it is adopted in the future for
some specified use, suitable mnemonics will be added to the assembler. Until such time, this instruction
shall not be used.
60
Instruction Set - Examples
4.15 Instruction Set Examples
The following examples show ways in which the basic ARM60 instructions can combine to give efficient
code. None of these methods saves a great deal of execution time (although they may save some), mostly
they just save code.
4.15.1 Using the conditional instructions
(1)
using conditionals for logical OR
CMP
BEQ
CMP
BEQ
Rn,#p
Label
Rm,#q
Label
; if Rn=p OR Rm=q THEN GOTO Label
can be replaced by
CMP
CMPNE
BEQ
(2)
Div1
; test sign
; and 2's complement if necessary
Rc,Ra,LSL#2
Rb,#5
Rc,Rc,Ra
Rc,Rc,Ra
;
;
;
;
multiply by 4
test value
complete multiply by 5
complete multiply by 6
combining discrete and range tests
TEQ
CMPNE
MOVLS
(5)
Rn,#0
Rn,Rn,#0
multiplication by 4, 5 or 6 (run time)
MOV
CMP
ADDCS
ADDHI
(4)
; if condition not satisfied try other test
absolute value
TEQ
RSBMI
(3)
Rn,#p
Rm,#q
Label
Rc,#127
Rc,#” “-1
Rc,#”.”
;
;
;
;
discrete test
range test
IF
Rc<=” “ OR Rc=ASCII(127)
THEN Rc:=”.”
division and remainder
MOV
CMP
CMPCC
MOVCC
MOVCC
Rcnt,#1
Rb,#0x80000000
Rb,Ra
Rb,Rb,ASL#1
Rcnt,Rcnt,ASL#1
; enter with numbers in Ra and Rb
;
; bit to control the division
; move Rb until greater than Ra
61
P60ARM-B
Div2
BCC
MOV
CMP
SUBCS
ADDCS
MOVS
MOVNE
BNE
Div1
Rc,#0
Ra,Rb
Ra,Ra,Rb
Rc,Rc,Rcnt
Rcnt,Rcnt,LSR#1
Rb,Rb,LSR#1
Div2
;
;
;
;
;
test for possible subtraction
subtract if ok
put relevant bit into result
shift control bit
halve unless finished
;
; divide result in Rc
; remainder in Ra
4.15.2 Pseudo random binary sequence generator
It is often necessary to generate (pseudo-) random numbers and the most efficient algorithms are based on
shift generators with exclusive-OR feedback rather like a cyclic redundancy check generator. Unfortunately
the sequence of a 32 bit generator needs more than one feedback tap to be maximal length (i.e. 2^32-1 cycles
before repetition), so this example uses a 33 bit register with taps at bits 33 and 20. The basic algorithm is
newbit:=bit 33 eor bit 20, shift left the 33 bit number and put in newbit at the bottom; this operation is
performed for all the newbits needed (i.e. 32 bits). The entire operation can be done in 5 S cycles:
TST
MOVS
ADC
EOR
EOR
Rb,Rb,LSR#1
Rc,Ra,RRX
Rb,Rb,Rb
Rc,Rc,Ra,LSL#12
Ra,Rc,Rc,LSR#20
; enter with seed in Ra (32 bits),
Rb (1 bit in Rb lsb), uses Rc
;
; top bit into carry
; 33 bit rotate right
; carry into lsb of Rb
; (involved!)
; (similarly involved!)
;
; new seed in Ra, Rb as before
4.15.3 Multiplication by constant using the barrel shifter
(1)
Multiplication by 2^n (1,2,4,8,16,32..)
MOV
(2)
Multiplication by 2^n+1 (3,5,9,17..)
ADD
(3)
Ra,Ra,Ra,LSL #n
Multiplication by 2^n-1 (3,7,15..)
RSB
62
Ra, Rb, LSL #n
Ra,Ra,Ra,LSL #n
Instruction Set - Examples
(4)
Multiplication by 6
ADD
MOV
(5)
Ra,Ra,Ra,LSL #1
Ra,Ra,LSL#1
; multiply by 3
; and then by 2
Multiply by 10 and add in extra number
ADD
ADD
(6)
Ra,Ra,Ra,LSL#2
Ra,Rc,Ra,LSL#1
; multiply by 5
; multiply by 2 and add in next digit
General recursive method for Rb := Ra*C, C a constant:
(a)
If C even, say C = 2^n*D, D odd:
D=1:
D<>1:
(b)
If C MOD 4 = 1, say C = 2^n*D+1, D odd, n>1:
D=1:
D<>1:
(c)
MOV
Rb,Ra,LSL #n
{Rb := Ra*D}
MOV
Rb,Rb,LSL #n
ADD
Rb,Ra,Ra,LSL #n
{Rb := Ra*D}
ADD
Rb,Ra,Rb,LSL #n
If C MOD 4 = 3, say C = 2^n*D-1, D odd, n>1:
D=1:
D<>1:
RSB
Rb,Ra,Ra,LSL #n
{Rb := Ra*D}
RSB
Rb,Ra,Rb,LSL #n
This is not quite optimal, but close. An example of its non-optimality is multiply by 45 which is done by:
RSB
RSB
ADD
Rb,Ra,Ra,LSL#2
Rb,Ra,Rb,LSL#2
Rb,Ra,Rb,LSL# 2
; multiply by 3
; multiply by 4*3-1 = 11
; multiply by 4*11+1 = 45
Rb,Ra,Ra,LSL#3
Rb,Rb,Rb,LSL#2
; multiply by 9
; multiply by 5*9 = 45
rather than by:
ADD
ADD
63
P60ARM-B
4.15.4 Loading a word from an unknown alignment
BIC
LDMIA
AND
MOVS
MOVNE
Rb,Ra,#3
Rb,{Rd,Rc}
Rb,Ra,#3
Rb,Rb,LSL#3
Rd,Rd,LSR Rb
RSBNE
ORRNE
Rb,Rb,#32
Rd,Rd,Rc,LSL Rb
;
;
;
;
;
;
;
;
;
;
;
;
enter with address in Ra (32 bits)
uses Rb, Rc; result in Rd.
Note d must be less than c e.g. 0,1
get word aligned address
get 64 bits containing answer
correction factor in bytes
...now in bits and test if aligned
produce bottom of result word
(if not aligned)
get other shift amount
combine two halves to get result
4.15.5 Loading a halfword (Little Endian)
LDR
MOV
MOV
Ra, [Rb,#2]
Ra,Ra,LSL #16
Ra,Ra,LSR #16
;
;
;
;
Get halfword to bits 15:0
move to top
and back to bottom
use ASR to get sign extended version
4.15.6 Loading a halfword (Big Endian)
LDR
MOV
64
Ra, [Rb,#2]
Ra,Ra,LSR #16
; Get halfword to bits 31:16
; and back to bottom
; use ASR to get sign extended version
Memory Interface
5.0 Memory Interface
ARM60 communicates with its memory system via a bidirectional data bus (D[31:0]). A separate 32 bit
address bus specifies the memory location to be used for the transfer, and the nRW signal gives the
direction of transfer (ARM60 to memory or memory to ARM60). Control signals give additional
information about the transfer cycle, and in particular they facilitate the use of DRAM page mode where
applicable. Interfaces to static RAM based memories can also be interfaced to and, in general, they are much
simpler than the DRAM interface described here.
5.1 Cycle types
All memory transfer cycles can be placed in one of four categories:
(1)
Non-sequential cycle. ARM60 requests a transfer to or from an address which is unrelated to the
address used in the preceding cycle.
(2)
Sequential cycle. ARM60 requests a transfer to or from an address which is either the same as the
address in the preceding cycle, or is one word after the preceding address.
(3)
Internal cycle. ARM60 does not require a transfer, as it is performing an internal function and no
useful prefetching can be performed at the same time.
(4)
Coprocessor register transfer. ARM60 wishes to use the data bus to communicate with a
coprocessor, but does not require any action by the memory system.
These four classes are distinguishable to the memory system by inspection of the nMREQ and SEQ control
lines (see Table 6: Memory Cycle Types). These control lines are generated during phase 1 of the cycle before
the cycle whose characteristics they forecast, and this pipelining of the control information gives the
memory system sufficient time to decide whether or not it can use a page mode access.
nMREQ
SEQ
Cycle type
0
0
Non-sequential cycle
0
1
Sequential cycle
(S-cycle)
1
0
Internal cycle
(I-cycle)
1
1
Coprocessor register transfer
(N-cycle)
(C-cycle)
Table 6: Memory Cycle Types
Figure 29: ARM Memory Cycle Timing shows the pipelining of the control signals, and suggests how the
DRAM address strobes (nRAS and nCAS) might be timed to use page mode for S-cycles. Note that the Ncycle is longer than the other cycles. This is to allow for the DRAM precharge and row access time, and is
not an ARM60 requirement.
65
P60ARM-B
N-cycle
S-cycle
I-cycle
C-cycle
MCLK
A[31:0]
a
a+4
a+8
nMREQ
SEQ
nRAS
nCAS
D[31:0]
Figure 29: ARM Memory Cycle Timing
When an S-cycle follows an N-cycle, the address will always be one word greater than the address used in
the N-cycle. This address (marked ÒaÓ in the above diagram) should be checked to ensure that it is not the
last in the DRAM page before the memory system commits to the S-cycle. If it is at the page end, the S-cycle
cannot be performed in page mode and the memory system will have to perform a full access.
The processor clock must be stretched to match the full access. When an S-cycle follows an I- or C-cycle, the
address will be the same as that used in the I- or C-cycle. This fact may be used to start the DRAM access
during the preceding cycle, which enables the S-cycle to run at page mode speed whilst performing a full
DRAM access. This is shown in Figure 30: Memory Cycle Optimization.
5.2 Byte addressing
The processor address bus gives byte addresses, but instructions are always words (where a word is 4
bytes) and data quantities are usually words. Single data transfers (LDR and STR) can, however, specify
that a byte quantity is required. The nBW control line is used to request a byte from the memory system;
normally it is HIGH, signifying a request for a word quantity, and it goes LOW during phase 2 of the
preceding cycle to request a byte transfer.
When the processor is fetching an instruction from memory, the state of the bottom two address lines A[1:0]
is undefined.
When a byte is requested in a read transfer (LDRB), the memory system can safely ignore that the request
is for a byte quantity and present the whole word.
ARM60 will perform the byte extraction internally. Alternatively, the memory system may activate only the
addressed byte of the memory. This may be desirable in order to save power, or to enable the use of a
common decoding system for both read and write cycles.
66
Memory Interface
I-cycle
S-cycle
MCLK
A[31:0]
nMREQ
SEQ
nRAS
nCAS
D[31:0]
Figure 30: Memory Cycle Optimization
If a byte write is requested (STRB), ARM60 will broadcast the byte value across the data bus, presenting it
at each byte location within the word. The memory system must decode A[1:0] to enable writing only to the
addressed byte.
One way of implementing the byte decode in a DRAM system is to separate the 32 bit wide block of DRAM
into four byte wide banks, and generate the column address strobes independently as shown in Figure 31:
Decoding Byte Accesses to Memory.
When the processor is configured for Little Endian operation byte 0 of the memory system should be
connected to data lines 7 through 0 (D[7:0]) and strobed by nCAS0. nCAS1 drives the bank connected to
data lines 15 though 8, and so on. This has the added advantage of reducing the load on each column strobe
driver, which improves the precision of this time critical signal.
In the Big Endian case, byte 0 of the memory system should be connected to data lines 31 through 24.
67
P60ARM-B
A[0]
A[1]
nBW
MCLK
CAS
G
NCAS0
NCAS1
D
Q
Quad
Latch
NCAS2
NCAS3
Figure 31: Decoding Byte Accesses to Memory
5.3 Address timing
Normally the processor address changes during phase 2 to the value which the memory system should use
during the following cycle. This gives maximum time for driving the address to large memory arrays, and
for address translation where required. Dynamic memories usually latch the address on chip, and if the
latch is timed correctly they will work even though the address changes before the access has completed.
Static RAMs and ROMs will not work under such circumstances, as they require the address to be stable
until after the access has completed. Therefore, for use with such devices, the address transition must be
delayed until after the end of phase 2. An on-chip address latch, controlled by ALE, allows the address
timing to be modified in this way. In a system with a mixture of static and dynamic memories (which for
these purposes means a mixture of devices with and without address latches), the use of ALE may change
dynamically from one cycle to the next, at the discretion of the memory system.
5.4 Memory management
The ARM60 address bus may be processed by an address translation unit before being presented to the
memory, and ARM60 is capable of running a virtual memory system. The abort input to the processor may
be used by the memory manager to inform ARM60 of page faults. Various other signals enable different
page protection levels to be supported:
(1)
nRW can be used by the memory manager to protect pages from being written to.
(2)
nTRANS indicates whether the processor is in user or a privileged mode, and may be used to
protect system pages from the user, or to support completely separate mappings for the system and
the user.
68
Memory Interface
Address translation will normally only be necessary on an N-cycle, and this fact may be exploited to reduce
power consumption in the memory manager and avoid the translation delay at other times. The times when
translation is necessary can be deduced by keeping track of the cycle types that the processor uses.
If an N-cycle is matched to a full DRAM access, it will be longer than the minimum processor cycle time.
Stretching phase 1 rather than phase 2 will give the translation system more time to generate an abort
(which must be set up to the end of phase 1).
5.5 Locked operations
ARM60 includes a data swap (SWP) instruction that allows the contents of a memory location to be
swapped with the contents of a processor register. This instruction is implemented as an uninterruptable
pair of accesses; the first access reads the contents of the memory, and the second writes the register data to
the memory. These accesses must be treated as a contiguous operation by the memory controller to prevent
another device from changing the affected memory location before the swap is completed. ARM60 drives
the LOCK signal HIGH for the duration of the swap operation to warn the memory controller not to give
the memory to another device.
5.6 Stretching access times
All memory timing is defined by MCLK, and long access times can be accommodated by stretching this
clock. It is usual to stretch the LOW period of MCLK, as this allows the memory manager to abort the
operation if the access is eventually unsuccessful (ABORT must be setup prior to the rising edge of MCLK
if LATEABT is LOW configuring ARM60 for early aborts).
Either MCLK can be stretched before it is applied to ARM60, or the nWAIT input can be used together with
a free-running MCLK. Taking nWAIT LOW has the same effect as stretching the LOW period of MCLK,
and nWAIT must only change when MCLK is LOW.
ARM60 does not contain any dynamic logic which relies upon regular clocking to maintain its internal state.
Therefore there is no limit upon the maximum period for which MCLK may be stretched, or nWAIT held
LOW.
69
P60ARM-B
70
Coprocessor Interface
6.0 Coprocessor Interface
The functionality of the ARM60 instruction set may be extended by the addition of up to 16 external
coprocessors. When the coprocessor is not present, instructions intended for it will trap, and suitable
software may be installed to emulate its functions. Adding the coprocessor will then increase the system
performance in a software compatible way. Note that some coprocessor numbers have already been
assigned. Contact your supplier for up to date information.
6.1 Interface signals
Three dedicated signals control the coprocessor interface, nCPI, CPA and CPB. The CPA and CPB inputs
should be driven high except when they are being used for handshaking.
6.1.1 Coprocessor present/absent
ARM60 takes nCPI LOW whenever it starts to execute a coprocessor (or undefined) instruction. (This will
not happen if the instruction fails to be executed because of the condition codes.) Each coprocessor will have
a copy of the instruction, and can inspect the CP# field to see which coprocessor it is for. Every coprocessor
in a system must have a unique number and if that number matches the contents of the CP# field the
coprocessor should drive the CPA (coprocessor absent) line LOW. If no coprocessor has a number which
matches the CP# field, CPA and CPB will remain HIGH, and ARM60 will take the undefined instruction
trap. Otherwise ARM60 observes the CPA line going LOW, and waits until the coprocessor is not busy.
6.1.2 Busy-waiting
If CPA goes LOW, ARM60 will watch the CPB (coprocessor busy) line. Only the coprocessor which is
driving CPA LOW is allowed to drive CPB LOW, and it should do so when it is ready to complete the
instruction. ARM60 will busy-wait while CPB is HIGH, unless an enabled interrupt occurs, in which case
it will break off from the coprocessor handshake to process the interrupt. Normally ARM60 will return from
processing the interrupt to retry the coprocessor instruction.
When CPB goes LOW, the instruction continues to completion. This will involve data transfers taking place
between the coprocessor and either ARM60 or memory, except in the case of coprocessor data operations
which complete immediately the coprocessor ceases to be busy.
All three interface signals are sampled by both ARM60 and the coprocessor(s) on the rising edge of MCLK.
If all three are LOW, the instruction is committed to execution, and if transfers are involved they will start
on the next cycle. If nCPI has gone HIGH after being LOW, and before the instruction is committed, ARM60
has broken off from the busy-wait state to service an interrupt. The instruction may be restarted later, but
other coprocessor instructions may come sooner, and the instruction should be discarded.
6.1.3 Pipeline following
In order to respond correctly when a coprocessor instruction arises, each coprocessor must have a copy of
the instruction. All ARM60 instructions are fetched from memory via the main data bus, and coprocessors
are connected to this bus, so they can keep copies of all instructions as they go into the ARM60 pipeline. The
nOPC signal indicates when an instruction fetch is taking place, and MCLK gives the timing of the transfer,
so these may be used together to load an instruction pipeline within the coprocessor.
71
P60ARM-B
6.2 Data transfer cycles
Once the coprocessor has gone not-busy in a data transfer instruction, it must supply or accept data at the
ARM60 bus rate (defined by MCLK and nWAIT). It can deduce the direction of transfer by inspection of
the L bit in the instruction, but must only drive the bus when permitted to by DBE being HIGH. The
coprocessor is responsible for determining the number of words to be transferred; ARM60 will continue to
increment the address by one word per transfer until the coprocessor tells it to stop. The termination
condition is indicated by the coprocessor driving CPA and CPB HIGH.
There is no limit in principle to the number of words which one coprocessor data transfer can move, but by
convention no coprocessor should allow more than 16 words in one instruction. More than this would
worsen the worst case ARM60 interrupt latency, as the instruction is not interruptible once the transfers
have commenced. At 16 words, this instruction is comparable with a block transfer of 16 registers, and
therefore does not affect the worst case latency.
6.3 Register transfer cycle
The coprocessor register transfer cycle is the one case when ARM60 requires the data bus without requiring
the memory to be active. The memory system is informed that the bus is required by ARM60 taking both
nMREQ and SEQ HIGH. When the bus is free, DBE should be taken HIGH to allow ARM60 or the
coprocessor to drive the bus.
6.4 Privileged instructions
The coprocessor may restrict certain instructions for use in privileged modes only. To do this, the
coprocessor will have to track the nTRANS output.
As an example of the use of this facility, consider the case of a floating point coprocessor (FPU) in a multitasking system. The operating system could save all the floating point registers on every task switch, but
this is inefficient in a typical system where only one or two tasks will use floating point operations. Instead,
there could be a privileged instruction which turns the FPU on or off. When a task switch happens, the
operating system can turn the FPU off without saving its registers. If the new task attempts an FPU
operation, the FPU will appear to be absent, causing an undefined instruction trap. The operating system
will then realise that the new task requires the FPU, so it will re-enable it and save FPU registers. The task
can then use the FPU as normal. If, however, the new task never attempts an FPU operation (as will be the
case for most tasks), the state saving overhead will have been avoided.
6.5 Idempotency
A consequence of the implementation of the coprocessor interface, with the interruptible busy-wait state, is
that all instructions may be interrupted at any point up to the time when the coprocessor goes not-busy. If
so interrupted, the instruction will normally be restarted from the beginning after the interrupt has been
processed. It is therefore essential that any action taken by the coprocessor before it goes not-busy must be
idempotent, ie must be repeatable with identical results.
For example, consider a FIX operation in a floating point coprocessor which returns the integer result to an
ARM60 register. The coprocessor must stay busy while it performs the floating point to fixed point
conversion, as ARM60 will expect to receive the integer value on the cycle immediately following that
72
Coprocessor Interface
where it goes not-busy. The coprocessor must therefore preserve the original floating point value and not
corrupt it during the conversion, because it will be required again if an interrupt arises during the busy
period.
The coprocessor data operation class of instruction is not generally subject to idempotency considerations,
as the processing activity can take place after the coprocessor goes not-busy. There is no need for ARM60
to be held up until the result is generated, because the result is confined to stay within the coprocessor.
6.6 UndeÞned instructions
Undefined instructions are treated by ARM60 as coprocessor instructions. All coprocessors must be absent
(ie CPA and CPB must be HIGH) when an undefined instruction is presented. ARM60 will then take the
undefined instruction trap. Note that the coprocessor need only look at bit 27 of the instruction to
differentiate undefined instructions (which all have 0 in bit 27) from coprocessor instructions (which all
have 1 in bit 27).
73
P60ARM-B
74
Instruction Cycle Operations
7.0 Instruction Cycle Operations
In the following tables nMREQ and SEQ (which are pipelined up to one cycle ahead of the cycle to which
they apply) are shown in the cycle in which they appear, so they predict the type of the next cycle. The
address, nBW, nRW, and nOPC (which appear up to half a cycle ahead) are shown in the cycle to which
they apply.
Key:-
(pc)
Xn
=
=
contents of the pc.
exception vector
¥
=
a varying number
7.1 Branch and branch with link
A branch instruction calculates the branch destination in the first cycle, whilst performing a prefetch from
the current PC. This prefetch is done in all cases, since by the time the decision to take the branch has been
reached it is already too late to prevent the prefetch.
During the second cycle a fetch is performed from the branch destination, and the return address is stored
in register 14 if the link bit is set.
The third cycle performs a fetch from the destination + 4, refilling the instruction pipeline, and if the branch
is with link R14 is modified (4 is subtracted from it) to simplify return from SUB PC,R14,#4 to MOV PC,R14.
This makes the STM..{R14} LDM..{PC} type of subroutine work correctly. The cycle timings are shown
below in Table 7: Branch Instruction Cycle Operations
Cycle
Address
nBW
nRW
Data
nMREQ
SEQ
nOPC
1
pc+8
1
0
(pc + 8)
0
0
0
2
alu
1
0
(alu)
0
1
0
3
alu+4
1
0
(alu + 4)
0
1
0
alu+8
Table 7: Branch Instruction Cycle Operations
pc is the address of the branch instruction
alu is an address calculated by ARM60
(alu) are the contents of that address, etc
7.2 Data Operations
A data operation executes in a single datapath cycle except where the shift is determined by the contents of
a register. A register is read onto the A bus, and a second register or the immediate field onto the B bus. The
ALU combines the A bus source and the shifted B bus source according to the operation specified in the
instruction, and the result (when required) is written to the destination register. (Compares and tests do not
produce results, only the ALU status flags are affected.)
75
P60ARM-B
An instruction prefetch occurs at the same time as the above operation, and the program counter is
incremented.
When the shift length is specified by a register, an additional datapath cycle occurs before the above
operation to copy the bottom 8 bits of that register into a holding latch in the barrel shifter. The instruction
prefetch will occur during this first cycle, and the operation cycle will be internal (ie will not request
memory). This internal cycle can be merged with the following sequential access by the memory manager
as the address remains stable through both cycles.
The PC may be one or more of the register operands. When it is the destination external bus activity may
be affected. If the result is written to the PC, the contents of the instruction pipeline are invalidated, and the
address for the next instruction prefetch is taken from the ALU rather than the address incrementer. The
instruction pipeline is refilled before any further execution takes place, and during this time exceptions are
locked out, although will be recorded for subsequent action after the pipeline has been refilled.
PSR Transfer operations exhibit the same timing characteristics as the data operations except that the PC is
never used as a source or destination register. The cycle timings are shown below Table 8: Data Operation
Instruction Cycle Operations.
normal
Cycle
Address
nBW
nRW
1
pc+8
1
0
Data
nMREQ
SEQ
nOPC
(pc+8)
0
1
0
pc+12
dest=pc
1
pc+8
1
0
(pc+8)
0
0
0
2
alu
1
0
(alu)
0
1
0
3
alu+4
1
0
(alu+4)
0
1
0
alu+8
shift(Rs)
1
pc+8
1
0
(pc+8)
1
0
0
2
pc+12
1
0
-
0
1
1
pc+12
shift(Rs)
1
pc+8
1
0
(pc+8)
1
0
0
dest=pc
2
pc+12
1
0
-
0
0
1
3
alu
1
0
(alu)
0
1
0
4
alu+4
1
0
(alu+4)
0
1
0
alu+8
Table 8: Data Operation Instruction Cycle Operations
76
Instruction Cycle Operations
7.3 Multiply and multiply accumulate
The multiply instructions make use of special hardware which implements a 2 bit Booth's algorithm with
early termination. During the first cycle the accumulate Register is brought to the ALU, which either
transmits it or produces zero (depending on the instruction being MLA or MUL) to initialise the destination
register. During the same cycle, the multiplier (Rs) is loaded into the Booth's shifter via the A bus.
The datapath then cycles, adding the multiplicand (Rm) to, subtracting it from, or just transmitting, the
result register. The multiplicand is shifted in the Nth cycle by 2N or 2N+1 bits, under control of the Booth's
logic. The multiplier is shifted right 2 bits per cycle, and when it is zero the instruction terminates (possibly
after an additional cycle to clear a pending borrow).
All cycles except the first are internal. The cycle timings are shown below in Table 9: Multiply Instruction
Cycle Operations.
Cycle
(Rs)=0,1
Address
nBW
nRW
Data
nMREQ
SEQ
nOPC
1
pc+8
1
0
(pc+8)
1
0
0
2
pc+12
1
0
-
0
1
1
pc+12
(Rs)>1
(pc+8)
1
pc+8
1
0
(pc+8)
1
0
0
2
pc+12
1
0
-
1
0
1
•
pc+12
1
0
-
1
0
1
m
pc+12
1
0
-
1
0
1
m+1
pc+12
1
0
-
0
1
1
pc+12
Table 9: Multiply Instruction Cycle Operations
m is the number of cycles required by the Booth's algorithm; see the section on instruction speeds.
77
P60ARM-B
7.4 Load register
The first cycle of a load register instruction performs the address calculation. The data is fetched from
memory during the second cycle, and the base register modification is performed during this cycle (if
required). During the third cycle the data is transferred to the destination register, and external memory is
unused. This third cycle may normally be merged with the following prefetch to form one memory N-cycle.
The cycle timings are shown below in Table 10: Load Register Instruction Cycle Operations.
Either the base or the destination (or both) may be the PC, and the prefetch sequence will be changed if the
PC is affected by the instruction.
The data fetch may abort, and in this case the destination modification is prevented. In addition, if the
processor is configured for Early Abort, the base register write-back is also prevented.
Cycle
normal
Address
1
pc+8
2
alu
3
pc+12
nBW
nRW
Data
nMREQ
SEQ
nOPC
1
0
(pc+8)
0
0
0
b/w
0
(alu)
1
0
1
1
0
-
0
1
1
1
0
(pc+8)
0
0
0
b/w
0
pc’
1
0
1
pc+12
dest=pc
1
pc+8
2
alu
3
pc+12
1
0
-
0
0
1
4
pc’
1
0
(pc’)
0
1
0
5
pc’+4
1
0
(pc’+4)
0
1
0
pc’+8
Table 10: Load Register Instruction Cycle Operations
78
Instruction Cycle Operations
7.5 Store register
The first cycle of a store register is similar to the first cycle of load register. During the second cycle the base
modification is performed, and at the same time the data is written to memory. There is no third cycle. The
cycle timings are shown below in Table 11: Store Register Instruction Cycle Operations. The base write-back
is prevented during a Data Abort if the processor is configured for Early Abort. The write-back is not
prevented if Late Abort is configured.
Cycle
Address
1
pc+8
2
alu
nBW
nRW
Data
nMREQ
SEQ
nOPC
1
0
(pc+8)
0
0
0
b/w
1
Rd
0
0
1
pc+12
Table 11: Store Register Instruction Cycle Operations
7.6 Load multiple registers
The first cycle of LDM is used to calculate the address of the first word to be transferred, whilst performing
a prefetch from memory. The second cycle fetches the first word, and performs the base modification.
During the third cycle, the first word is moved to the appropriate destination register while the second
word is fetched from memory, and the modified base is latched internally in case it is needed to patch up
after an abort. The third cycle is repeated for subsequent fetches until the last data word has been accessed,
then the final (internal) cycle moves the last word to its destination register. The cycle timings are shown in
Table 12: Load Multiple Registers Instruction Cycle Operations.
The last cycle may be merged with the next instruction prefetch to form a single memory N-cycle.
If an abort occurs, the instruction continues to completion, but all register writing after the abort is
prevented. The final cycle is altered to restore the modified base register (which may have been overwritten
by the load activity before the abort occurred).
When the PC is in the list of registers to be loaded the current instruction pipeline must be invalidated.
Note that the PC is always the last register to be loaded, so an abort at any point will prevent the PC from
being overwritten.
79
P60ARM-B
Cycle
1 register
Address
nBW
nRW
Data
nMREQ
SEQ
nOPC
1
pc+8
1
0
(pc+8)
0
0
0
2
alu
1
0
(alu)
1
0
1
3
pc+12
1
0
-
0
1
1
pc+12
1 register
1
pc+8
1
0
(pc+8)
0
0
0
dest=pc
2
alu
1
0
pc’
1
0
1
3
pc+12
1
0
-
0
0
1
4
pc’
1
0
(pc’)
0
1
0
5
pc’+4
1
0
(pc’+4)
0
1
0
pc’+8
n registers
1
pc+8
1
0
(pc+8)
0
0
0
(n>1)
2
alu
1
0
(alu)
0
1
1
•
alu+•
1
0
(alu+•)
0
1
1
n
alu+•
1
0
(alu+•)
0
1
1
n+1
alu+•
1
0
(alu+•)
1
0
1
n+2
pc+12
1
0
-
0
1
1
pc+12
n registers
1
pc+8
1
0
(pc+8)
0
0
0
(n>10)
2
alu
1
0
(alu)
0
1
1
incl pc
•
alu+•
1
0
(alu+•)
0
1
1
n
alu+•
1
0
(alu+•)
0
1
1
n+1
alu+•
1
0
pc’
1
0
1
n+2
pc+12
1
0
-
0
0
1
n+3
pc’
1
0
(pc’)
0
1
0
n+4
pc’+4
1
0
(pc’+4)
0
1
0
pc’+8
Table 12: Load Multiple Registers Instruction Cycle Operations
80
Instruction Cycle Operations
7.7 Store multiple registers
Store multiple proceeds very much as load multiple, without the final cycle. The restart problem is much
more straightforward here, as there is no wholesale overwriting of registers to contend with. The cycle
timings are shown in Table 13: Store Multiple Registers Instruction Cycle Operations.
Cycle
1 register
Address
nBW
nRW
Data
nMREQ
SEQ
nOPC
1
pc+8
1
0
(pc+8)
0
0
0
2
alu
1
1
Ra
0
0
1
pc+12
n registers
1
pc+8
1
0
(pc+8)
0
0
0
(n>1)
2
alu
1
1
Ra
0
1
1
•
alu+•
1
1
R•
0
1
1
n
alu+•
1
1
R•
0
1
1
n+1
alu+•
1
1
R•
0
0
1
pc+12
Table 13: Store Multiple Registers Instruction Cycle Operations
7.8 Data swap
This is similar to the load and store register instructions, but the actual swap takes place in cycles 2 and 3.
In the second cycle, the data is fetched from external memory. In the third cycle, the contents of the source
register are written out to the external memory. The data read in cycle 2 is written into the destination
register during the fourth cycle. The cycle timings are shown below in Table 14: Data Swap Instruction Cycle
Operations.
The LOCK output of ARM60 is driven HIGH for the duration of the swap operation (cycles 2 & 3) to
indicate that both cycles should be allowed to complete without interruption.
The data swapped may be a byte or word quantity (b/w).
The swap operation may be aborted in either the read or write cycle, and in both cases the destination
register will not be affected.
81
P60ARM-B
Cycle
Address
nBW
nRW
Data
nMREQ
SEQ
nOPC
LOCK
1
0
(pc+8)
0
0
0
0
1
pc+8
2
Rn
b/w
0
(Rn)
0
0
1
1
3
Rn
b/w
1
Rm
1
0
1
1
4
pc+12
1
0
-
0
1
1
0
pc+12
Table 14: Data Swap Instruction Cycle Operations
7.9 Software interrupt and exception entry
Exceptions (and software interrupts) force the PC to a particular value and refill the instruction pipeline
from there. During the first cycle the forced address is constructed, and a mode change may take place. The
return address is moved to R14 and the CPSR to SPSR_svc.
During the second cycle the return address is modified to facilitate return, though this modification is less
useful than in the case of branch with link.
The third cycle is required only to complete the refilling of the instruction pipeline. The cycle timings are
shown below in Table 15: Software Interrupt Instruction Cycle Operations.
Cycle
Address
nBW
nRW
Data
nMREQ
SEQ
nOPC
nTRANS
1
pc+8
1
0
(pc+8)
0
0
0
1
2
Xn
1
0
(Xn)
0
1
0
1
3
Xn+4
1
0
(Xn+4)
0
1
0
1
Xn+8
Table 15: Software Interrupt Instruction Cycle Operations
For software interrupts, pc is the address of the SWI instruction. For interrupts and reset, pc is the address
of the instruction following the last one to be executed before entering the exception. For prefetch abort, pc
is the address of the aborting instruction. For data abort, pc is the address of the instruction following the
one which attempted the aborted data transfer. Xn is the appropriate trap address.
82
Instruction Cycle Operations
7.10 Coprocessor data operation
A coprocessor data operation is a request from ARM60 for the coprocessor to initiate some action. The
action need not be completed for some time, but the coprocessor must commit to doing it before driving
CPB LOW.
If the coprocessor can never do the requested task, it should leave CPA and CPB HIGH. If it can do the task,
but can't commit right now, it should drive CPA LOW but leave CPB HIGH until it can commit. ARM60
will busy-wait until CPB goes LOW. The cycle timings are shown in Table 16: Coprocessor Data Operation
Instruction Cycle Operations.
Cycle
ready
1
Address
pc+8
nBW
nRW
Data
nMREQ
SEQ
nOPC
nCPI
CPA
CPB
1
0
(pc+8)
0
0
0
0
0
0
pc+12
not ready
1
pc+8
1
0
(pc+8)
1
0
0
0
0
1
2
pc+8
1
0
-
1
0
1
0
0
1
•
pc+8
1
0
-
1
0
1
0
0
1
n
pc+8
1
0
-
0
0
1
0
0
0
pc+12
Table 16: Coprocessor Data Operation Instruction Cycle Operations
7.11 Coprocessor data transfer (from memory to coprocessor)
Here the coprocessor should commit to the transfer only when it is ready to accept the data. When CPB goes
LOW, ARM60 will produce addresses and expect the coprocessor to take the data at sequential cycle rates.
The coprocessor is responsible for determining the number of words to be transferred, and indicates the last
transfer cycle by driving CPA and CPB HIGH.
ARM60 spends the first cycle (and any busy-wait cycles) generating the transfer address, and performs the
write-back of the address base during the transfer cycles. The cycle timings are shown in Table 17:
Coprocessor Data Transfer Instruction Cycle Operations.
83
P60ARM-B
Cycle
Address
nBW
nRW
Data
nMREQ
SEQ
nOPC
nCPI
CPA
CPB
1 register
1
pc+8
1
0
(pc+8)
0
0
0
0
0
0
ready
2
alu
1
0
(alu)
0
0
1
1
1
1
pc+12
1 register
1
pc+8
1
0
(pc+8)
1
0
0
0
0
1
not ready
2
pc+8
1
0
-
1
0
1
0
0
1
•
pc+8
1
0
-
1
0
1
0
0
1
n
pc+8
1
0
-
0
0
1
0
0
0
alu
1
0
(alu)
0
0
1
1
1
1
n+1
pc+12
n registers
1
pc+8
1
0
(pc+8)
0
0
0
0
0
0
(n>1)
2
alu
1
0
(alu)
0
1
1
1
0
0
ready
•
alu+•
1
0
(alu+•)
0
1
1
1
0
0
n
alu+•
1
0
(alu+•)
0
1
1
1
0
0
n+1
alu+•
1
0
(alu+•)
0
0
1
1
1
1
pc+12
m registers
1
pc+8
1
0
(pc+8)
1
0
0
0
0
1
(m>1)
2
pc+8
1
0
-
1
0
1
0
0
1
not ready
•
pc+8
1
0
-
1
0
1
0
0
1
n
pc+8
1
0
-
0
0
1
0
0
0
alu
1
0
(alu)
0
1
1
1
0
0
•
alu+•
1
0
(alu+•)
0
1
1
1
0
0
n+m
alu+•
1
0
(alu+•)
0
1
1
1
0
0
n+m+1
alu+•
1
0
(alu+•)
0
0
1
1
1
1
n+1
pc+12
Table 17: Coprocessor Data Transfer Instruction Cycle Operations
84
Instruction Cycle Operations
7.12 Coprocessor data transfer (from coprocessor to memory)
The ARM60 controls these instructions exactly as for memory to coprocessor transfers, with the one
exception that the nRW line is inverted during the transfer cycle. The cycle timings are show in Table 18:
Coprocessor Data Transfer Instruction Cycle Operations.
Cycle
Address
nBW
nRW
Data
nMREQ
SEQ
nOPC
nCPI
CPA
CPB
1 register
1
pc+8
1
0
(pc+8)
0
0
0
0
0
0
ready
2
alu
1
1
CPdata
0
0
1
1
1
1
pc+12
1 register
1
pc+8
1
0
(pc+8)
1
0
0
0
0
1
not ready
2
pc+8
1
0
-
1
0
1
0
0
1
•
pc+8
1
0
-
1
0
1
0
0
1
n
pc+8
1
0
-
0
0
1
0
0
0
alu
1
1
CPdata
0
0
1
1
1
1
n+1
pc+12
n registers
1
pc+8
1
0
(pc+8)
0
0
0
0
0
0
(n>1)
2
alu
1
1
CPdata
0
1
1
1
0
0
ready
•
alu+•
1
1
CPdata
0
1
1
1
0
0
n
alu+•
1
1
CPdata
0
1
1
1
0
0
n+1
alu+•
1
1
CPdata
0
0
1
1
1
1
pc+12
m registers
1
pc+8
1
0
(pc+8)
1
0
0
0
0
1
(m>1)
2
pc+8
1
0
-
1
0
1
0
0
1
not ready
•
pc+8
1
0
-
1
0
1
0
0
1
n
pc+8
1
0
-
0
0
1
0
0
0
alu
1
1
CPdata
0
1
1
1
0
0
•
alu+•
1
1
CPdata
0
1
1
1
0
0
n+m
alu+•
1
1
CPdata
0
1
1
1
0
0
n+m+1
alu+•
1
1
CPdata
0
0
1
1
1
1
n+1
pc+12
Table 18: Coprocessor Data Transfer Instruction Cycle Operations
85
P60ARM-B
7.13 Coprocessor register transfer (Load from coprocessor)
Here the busy-wait cycles are much as above, but the transfer is limited to one data word, and ARM60 puts
the word into the destination register in the third cycle. The third cycle may be merged with the following
prefetch cycle into one memory N-cycle as with all ARM60 register load instructions. The cycle timings are
shown in Table 19: Coprocessor register transfer (Load from coprocessor).
Cycle
ready
Address
nBW
nRW
Data
nMREQ
SEQ
nOPC
nCPI
CPA
CPB
1
pc+8
1
0
(pc+8)
1
1
0
0
0
0
2
pc+12
1
0
CPdata
1
0
1
1
1
1
3
pc+12
1
0
-
0
1
1
1
-
-
pc+12
not ready
1
pc+8
1
0
(pc+8)
1
0
0
0
0
1
2
pc+8
1
0
CPdata
1
0
1
0
0
1
•
pc+8
1
0
-
1
0
1
0
0
1
n
pc+8
1
0
-
1
1
1
0
0
0
n+1
pc+12
1
0
CPdata
1
0
1
1
1
1
n+2
pc+12
1
0
-
0
1
1
1
-
-
pc+12
Table 19: Coprocessor register transfer (Load from coprocessor)
7.14 Coprocessor register transfer (Store to coprocessor)
As for the load from coprocessor, except that the last cycle is omitted. The cycle timings are shown below
in Table 20: Coprocessor register transfer (Store to coprocessor).
86
Instruction Cycle Operations
Cycle
ready
Address
nBW
nRW
Data
nMREQ
SEQ
nOPC
nCPI
CPA
CPB
1
pc+8
1
0
(pc+8)
1
1
0
0
0
0
2
pc+12
1
1
Rd
0
0
1
1
1
1
pc+12
not ready
1
pc+8
1
0
(pc+8)
1
0
0
0
0
1
2
pc+8
1
0
-
1
0
1
0
0
1
•
pc+8
1
0
-
1
0
1
0
0
1
n
pc+8
1
0
-
1
1
1
0
0
0
n+1
pc+12
1
1
Rd
0
0
1
1
1
1
pc+12
Table 20: Coprocessor register transfer (Store to coprocessor)
7.15 UndeÞned instructions and coprocessor absent
When a coprocessor detects a coprocessor instruction which it cannot perform, and this must include all
undefined instructions, it must not drive CPA or CPB LOW. These will remain HIGH, causing the
undefined instruction trap to be taken. Cycle timings are shown in Table 21: Undefined Instruction Cycle
Operations.
Cycle
Address
nBW
nRW
Data
nMREQ
SEQ
nOPC
nCPI
CPA
CPB
1
pc+8
1
0
(pc+8)
1
0
0
0
1
1
2
pc+8
1
0
-
0
0
0
1
1
1
3
Xn
1
0
(Xn)
0
1
0
1
1
1
4
Xn+4
1
0
(Xn+4)
0
1
0
1
1
1
Xn+8
Table 21: Undefined Instruction Cycle Operations
7.16 Unexecuted instructions
Any instruction whose condition code is not met will fail to execute. It will add one cycle to the execution
time of the code segment in which it is embedded (see Table 22: Unexecuted Instruction Cycle Operations).
87
P60ARM-B
Cycle
1
Address
pc+8
nBW
nRW
Data
nMREQ
SEQ
nOPC
1
0
(pc+8)
0
1
0
pc+12
Table 22: Unexecuted Instruction Cycle Operations
7.17 Instruction Speed Summary
Due to the pipelined architecture of the CPU, instructions overlap considerably. In a typical cycle one
instruction may be using the data path while the next is being decoded and the one after that is being
fetched. For this reason the following table presents the incremental number of cycles required by an
instruction, rather than the total number of cycles for which the instruction uses part of the processor.
Elapsed time (in cycles) for a routine may be calculated from these figures which are shown in Table 23:
ARM Instruction Speeds. These figures assume that the instruction is actually executed. Unexecuted
instructions take one cycle.
Instruction
Cycle count
Data Processing
1S
MSR, MRS
LDR
STR
LDM
STM
SWP
B,BL
SWI, trap
MUL,MLA
CDP
LDC,STC
MRC
MCR
1S
1S
nS
(n-1)S
1S
2S
2S
1S
1S
(n-1)S
1S
1S
Additional
+ 1I
for SHIFT(Rs)
+ 1I + 1N if R15 written
+ 1N
2N
+ 1N
+ 2N
+ 2N
+ 1N
+ 1N
+
+
+ 2N
+
+
+ 1I
+ 1S + 1N
if R15 loaded
+ 1I
+ 1S + 1N
if R15 loaded
+ 1I
mI
bI
+ bI
bI
(b+1)I
+ 1C
+ 1C
Table 23: ARM Instruction Speeds
n
is the number of words transferred.
m
is the number of cycles required by the multiply algorithm, which is determined by the contents of
Rs. Multiplication by any number between 2^(2m-3) and 2^(2m-1)-1 takes 1S+mI m cycles for
1<m>16. Multiplication by 0 or 1 takes 1S+1I cycles, and multiplication by any number greater than
or equal to 2^(29) takes 1S+16I cycles. The maximum time for any multiply is thus 1S+16I cycles.
b
is the number of cycles spent in the coprocessor busy-wait loop.
If the condition is not met all instructions take one S cycle. The cycle types (N, S, I and C) are deÞned in
Chapter 5.0 Memory Interface.
88
Boundary Scan Test Interface
8.0 Boundary Scan Test Interface
The boundary-scan interface conforms to the IEEE Std. 1149.1- 1990, Standard Test Access Port and
Boundary-Scan Architecture (please refer to this standard for an explanation of the terms used in this
section and for a description of the TAP controller states.)
8.1 Overview
The boundary-scan interface provides a means of testing the core of the device when it is fitted to a circuit
board, and a means of driving and sampling all the external pins of the device irrespective of the core state.
This latter function permits testing of both the device's electrical connections to the circuit board, and (in
conjunction with other devices on the circuit board having a similar interface) testing the integrity of the
circuit board connections between devices. The interface intercepts all external connections within the
device, and each such ÒcellÓ is then connected together to form a serial register (the boundary scan register).
The whole interface is controlled via 5 dedicated pins: TDI, TMS, TCK, nTRST and TDO. Figure 32: Test
Access Port (TAP) Controller State Transitions shows the state transitions that occur in the TAP controller.
Test-Logic Reset
tms=1
tms=0
tms=1
tms=1
tms=1
Run-Test/Idle
Select-DR-Scan
tms=0
Select-IR-Scan
tms=0
tms=0
Capture-DR
Capture-IR
tms=1
tms=1
tms=0
tms=0
Shift-DR
Shift-IR
tms=1
tms=0
tms=1
Exit1-DR
tms=0
Exit1-IR
tms=1
tms=1
tms=0
tms=0
Pause-DR
Pause-IR
tms=1
tms=0
tms=0
tms=1
tms=0
tms=0
Exit2-DR
Exit2-IR
tms=1
tms=1
Update-DR
tms=1
Update-IR
tms=0
tms=1
tms=0
Figure 32: Test Access Port (TAP) Controller State Transitions
89
P60ARM-B
8.2 Reset
The boundary-scan interface includes a state-machine controller (the TAP controller). In order to force the
TAP controller into the correct state after power-up of the device, a reset pulse must be applied to the
nTRST pin. If the boundary scan interface is to be used, then nTRST must be driven LOW, and then HIGH
again. If the boundary scan interface is not to be used, then the nTRST pin may be tied permanently LOW.
Note that a clock on TCK is not necessary to reset the device.
The action of reset (either a pulse or a DC level) is as follows:
System mode is selected (i.e. the boundary scan chain does NOT intercept any of the signals passing
between the pads and the core).
IDcode mode is selected. If TMS and TCK are used to put the TAP controller in Shift-DR mode (see
Fig 32), the IDcode will be clocked out of TDO.
8.3 Pullup Resistors
TDI, TMS, nTRST and TCK all have on-chip pullup resistors.
8.4 Instruction Register
The instruction register is 4 bits in length.
There is no parity bit. The fixed value loaded into the instruction register during the CAPTURE-IR
controller state is: 0001.
8.5 Public Instructions
The following public instructions are supported:
Instruction
Binary Code
EXTEST
SAMPLE/PRELOAD
CLAMP
HIGHZ
CLAMPZ
INTEST
IDCODE
BYPASS
0000
0011
0101
0111
1001
1100
1110
1111
In the descriptions that follow, TDI and TMS are sampled on the rising edge of TCK and all output
transitions on TDO occur as a result of the falling edge of TCK.
8.5.1 EXTEST (0000)
The BS (boundary-scan) register is placed in test mode by the EXTEST instruction.
90
Boundary Scan Test Interface
The EXTEST instruction connects the BS register between TDI and TDO.
When the instruction register is loaded with the EXTEST instruction, all the boundary-scan cells are placed
in their test mode of operation.
In the CAPTURE-DR state, inputs from the system pins and outputs from the boundary-scan output cells
to the system pins are captured by the boundary-scan cells. In the SHIFT-DR state, the previously captured
test data is shifted out of the BS register via the TDO pin, whilst new test data is shifted in via the TDI pin
to the BS register parallel input latch. In the UPDATE-DR state, the new test data is transferred into the BS
register parallel output latch. Note that this data is applied immediately to the system logic and system
pins. The first EXTEST vector should be clocked into the boundary-scan register, using the SAMPLE/
PRELOAD instruction, prior to selecting INTEST to ensure that known data is applied to the system logic.
8.5.2 SAMPLE/PRELOAD (0011)
The BS (boundary-scan) register is placed in normal (system) mode by the SAMPLE/PRELOAD
instruction.
The SAMPLE/PRELOAD instruction connects the BS register between TDI and TDO.
When the instruction register is loaded with the SAMPLE/PRELOAD instruction, all the boundary-scan
cells are placed in their normal system mode of operation.
In the CAPTURE-DR state, a snapshot of the signals at the boundary-scan cells is taken on the rising edge
of TCK. Normal system operation is unaffected. In the SHIFT-DR state, the sampled test data is shifted out
of the BS register via the TDO pin, whilst new data is shifted in via the TDI pin to preload the BS register
parallel input latch. In the UPDATE-DR state, the preloaded data is transferred into the BS register parallel
output latch. Note that this data is not applied to the system logic or system pins while the SAMPLE/
PRELOAD instruction is active. This instruction should be used to preload the boundary-scan register with
known data prior to selecting the INTEST or EXTEST instructions (see the table below for appropriate
guard values to be used for each boundary-scan cell).
8.5.3 CLAMP (0101)
The CLAMP instruction connects a 1 bit shift register (the BYPASS register) between TDI and TDO.
When the CLAMP instruction is loaded into the instruction register, the state of all output signals is defined
by the values previously loaded into the boundary-scan register. A guarding pattern (specified for this
device at the end of this section) should be pre-loaded into the boundary-scan register using the SAMPLE/
PRELOAD instruction prior to selecting the CLAMP instruction.
In the CAPTURE-DR state, a logic 0 is captured by the bypass register. In the SHIFT-DR state, test data is
shifted into the bypass register via TDI and out via TDO after a delay of one TCK cycle. Note that the first
bit shifted out will be a zero. The bypass register is not affected in the UPDATE-DR state.
8.5.4 HIGHZ (0111)
The HIGHZ instruction connects a 1 bit shift register (the BYPASS register) between TDI and TDO.
91
P60ARM-B
When the HIGHZ instruction is loaded into the instruction register, all outputs are placed in an inactive
drive state.
In the CAPTURE-DR state, a logic 0 is captured by the bypass register. In the SHIFT-DR state, test data is
shifted into the bypass register via TDI and out via TDO after a delay of one TCK cycle. Note that the first
bit shifted out will be a zero. The bypass register is not affected in the UPDATE-DR state.
8.5.5 CLAMPZ (1001)
The CLAMPZ instruction connects a 1 bit shift register (the BYPASS register) between TDI and TDO.
When the CLAMPZ instruction is loaded into the instruction register, all outputs are placed in an inactive
drive state, but the data supplied to the disabled output drivers is derived from the boundary-scan cells.
The purpose of this instruction is to ensure, during production testing, that each output driver can be
disabled when its data input is either a 0 or a 1.
A guarding pattern (specified for this device at the end of this section) should be pre-loaded into the
boundary-scan register using the SAMPLE/PRELOAD instruction prior to selecting the CLAMPZ
instruction.
In the CAPTURE-DR state, a logic 0 is captured by the bypass register. In the SHIFT-DR state, test data is
shifted into the bypass register via TDI and out via TDO after a delay of one TCK cycle. Note that the first
bit shifted out will be a zero. The bypass register is not affected in the UPDATE-DR state.
8.5.6 INTEST (1100)
The BS (boundary-scan) register is placed in test mode by the INTEST instruction.
The INTEST instruction connects the BS register between TDI and TDO.
When the instruction register is loaded with the INTEST instruction, all the boundary-scan cells are placed
in their test mode of operation.
In the CAPTURE-DR state, the complement of the data supplied to the core logic from input boundary-scan
cells is captured, while the true value of the data that is output from the core logic to output boundary- scan
cells is captured. Note that CAPTURE-DR captures the complemented value of the input cells for testability
reasons.
In the SHIFT-DR state, the previously captured test data is shifted out of the BS register via the TDO pin,
whilst new test data is shifted in via the TDI pin to the BS register parallel input latch. In the UPDATE-DR
state, the new test data is transferred into the BS register parallel output latch. Note that this data is applied
immediately to the system logic and system pins. The first INTEST vector should be clocked into the
boundary-scan register, using the SAMPLE/PRELOAD instruction, prior to selecting INTEST to ensure
that known data is applied to the system logic.
Single-step operation is possible using the INTEST instruction.
92
Boundary Scan Test Interface
8.5.7 IDCODE (1110)
The IDCODE instruction connects the device identification register (or ID register) between TDI and TDO.
The ID register is a 32-bit register that allows the manufacturer, part number and version of a component
to be determined through the TAP.
When the instruction register is loaded with the IDCODE instruction, all the boundary-scan cells are placed
in their normal (system) mode of operation.
In the CAPTURE-DR state, the device identification code (specified at the end of this section) is captured
by the ID register. In the SHIFT-DR state, the previously captured device identification code is shifted out
of the ID register via the TDO pin, whilst data is shifted in via the TDI pin into the ID register. In the
UPDATE-DR state, the ID register is unaffected.
The device identification codes for the P60ARM (obsolete) and P60ARM-B are as follows:
P60ARM
P60ARM-B
1
3
D4A7
CCA
06F
06F
8.5.8 BYPASS (1111)
The BYPASS instruction connects a 1 bit shift register (the BYPASS register) between TDI and TDO.
When the BYPASS instruction is loaded into the instruction register, all the boundary-scan cells are placed
in their normal (system) mode of operation. This instruction has no effect on the system pins.
In the CAPTURE-DR state, a logic 0 is captured by the bypass register. In the SHIFT-DR state, test data is
shifted into the bypass register via TDI and out via TDO after a delay of one TCK cycle. Note that the first
bit shifted out will be a zero. The bypass register is not affected in the UPDATE-DR state.
93
P60ARM-B
8.6 Test Data Registers
Figure 33: Boundary Scan Block Diagram illustrates the structure of the boundary scan logic.
BSINENCELL
BSINCELL
BSINCELL
ARM
Core Logic
BSOUTCELL
BSOUTNENCELL
I/O
Cell
BSOUTCELL
Device ID Register
Bypass Register
TDO
Instruction Decoder
TDI
TMS
TCK
Instruction Register
TAP
Controller
nTDOEN
nTRST
Figure 33: Boundary Scan Block Diagram
8.6.1 Bypass Register
Purpose: This is a single bit register which can be selected as the path between TDI and TDO to allow the
device to be bypassed during boundary-scan testing.
Length: 1 bit
Operating Mode: When the BYPASS instruction is the current instruction in the instruction register, serial
data is transferred from TDI to TDO in the SHIFT-DR state with a delay of one TCK cycle.
94
Boundary Scan Test Interface
There is no parallel output from the bypass register.
A logic 0 is loaded from the parallel input of the bypass register in the CAPTURE-DR state.
8.6.2 ARM60 Device IdentiÞcation (ID) Code Register
Purpose: This register is used to read the 32-bit device identification code. No programmable
supplementary identification code is provided.
Length: 32 bits
The format of the ID register is as follows:
31
28
Version
27
12
11
Part Number
1
Manufacturer Identity
0
1
Please contact your supplier for the correct Device Identification Code.
Operating Mode: When the IDCODE instruction is current, the ID register is selected as the serial path
between TDI and TDO.
There is no parallel output from the ID register.
The 32-bit device identification code is loaded into the ID register from its parallel inputs during the
CAPTURE-DR state.
8.6.3 ARM60 Boundary Scan (BS) Register
Purpose: The BS register consists of a serially connected set of cells around the periphery of the device, at
the interface between the core logic and the system input/output pads. This register can be used to isolate
the core logic from the pins and then apply tests to the core logic, or conversely to isolate the pins from the
core logic and then drive or monitor the system pins.
Operating modes: The BS register is selected as the register to be connected between TDI and TDO only
during the SAMPLE/PRELOAD, EXTEST and INTEST instructions. Values in the BS register are used, but
are not changed, during the CLAMP and CLAMPZ instructions.
In the normal (system) mode of operation, straight-through connections between the core logic and pins are
maintained and normal system operation is unaffected.
In TEST mode (i.e. when either EXTEST or INTEST is the currently selected instruction), values can be
applied to the core logic or output pins independently of the actual values on the input pins and core logic
outputs respectively. On the ARM60 all of the boundary scan cells include an update register and thus all
of the pins can be controlled in the above manner. Additional boundary-scan cells are interposed in the scan
chain in order to control the enabling of tristateable buses.
95
P60ARM-B
The correspondence between boundary-scan cells and system pins, system direction controls and system
output enables is as shown in Table 25: Boundary Scan Signals & Pins . The cells are listed in the order in
which they are connected in the boundary-scan register, starting with the cell closest to TDI. All boundaryscan register cells at input pins can apply tests to the on-chip core logic.
The EXTEST guard values specified in Table 25: Boundary Scan Signals & Pins should be clocked into the
boundary-scan register (using the SAMPLE/PRELOAD instruction) before the EXTEST instruction is
selected, to ensure that known data is applied to the core logic during the test. The INTEST guard values
shown in the table below should be clocked into the boundary-scan register (using the SAMPLE/
PRELOAD instruction) before the INTEST instruction is selected to ensure that all outputs are disabled.
These guard values should also be used when new EXTEST or INTEST vectors are clocked into the
boundary-scan register.
The values stored in the BS register after power-up are not defined. Similarly, the values previously clocked
into the BS register are not guaranteed to be maintained across a Boundary Scan reset (from forcing nTRST
LOW or entering the Test Logic Reset state).
8.6.4 Output Enable Boundary-scan Cells
The boundary-scan register cells Nendout, Nabe, Ntbe, and Nmse control the output drivers of tristate
outputs as shown in the table 25. In the case of OUTEN0 enable cells (Nendout, Ntbe), loading a 1 into the
cell will place the associated drivers into the tristate state, while in the case of type INEN1 enable cells
(Nabe, Nmse), loading a 0 into the cell will tristate the associated drivers.
To put all ARM60 tristate outputs into their high impedance state, a logic 1 should be clocked into the
output enable boundary-scan cells Nendout and Ntbe, and a logic 0 should be clocked into Nabe and Nmse.
Alternatively, the HIGHZ instruction can be used.
If the on-chip core logic causes the drivers controlled by Nendout, for example, to be tristate, (i.e. by driving
the signal Nendout HIGH), then a 1 will be observed on this cell if the SAMPLE/PRELOAD or INTEST
instructions are active.
8.6.5 Single-step Operation
ARM60 is a static design and there is no minimum clock speed. It can therefore be single-stepped while the
INTEST instruction is selected. This can be achieved by serialising a parallel stimulus and clocking the
resulting serial vectors into the boundary-scan register. When the boundary-scan register is updated, new
test stimuli are applied to the core logic inputs; the effect of these stimuli can then be observed on the core
logic outputs by capturing them in the boundary-scan register.
96
Boundary Scan Test Interface
8.7 Boundary Scan Interface Signals
TCK
T bscl
TMS
TDI
T bsch
T bsis
T bsih
T bsss
T bssh
TDO
T bsoh
T bsod
Data In
Data Out
T bsdh
T bsdd
Figure 34: Boundary Scan General Timing
TCK
TDO
T bsoe
T bsoz
T bsde
T bsdz
Data Out
Figure 35: Boundary Scan Tri-state Timing
nTRST
T bsr
TMS
T bsrs
T bsrh
Figure 36: Boundary Scan Reset Timing
97
P60ARM-B
Symbol
Parameter
Min
Typ
Max
Units
Notes
Tbscl
TCK low period
48
ns
1
Tbsch
TCK high period
48
ns
1
Tbsis
TDI,TMS setup to [TCr]
10
ns
Tbsih
TDI,TMS hold from [TCr]
10
ns
Tbsod
TCf to TDO valid
Tbsoh
TDO hold time
Tbsoe
TDO enable time
Tbsoz
TDO disable time
Tbsss
I/O signal setup to [TCr]
Tbssh
I/O signal hold from [TCr]
Tbsdd
TCf to data output valid
Tbsdh
data output hold time
3
ns
6
Tbsde
data output enable time
5
ns
6,7
Tbsdz
data output disable time
ns
6,8
Tbsr
Reset period
20
ns
Tbsrs
tms setup to [TRr]
10
ns
9
Tbsrh
tms hold from [TRr]
10
ns
9
40
ns
2
3
ns
2
5
ns
2,3
ns
2,4
10
ns
5
15
ns
5
40
30
20
ns
Table 24: ARM60 Boundary Scan Interface Timing
Notes:
1.
TCK may be stopped indefinitely in either the low or high phase.
2.
Assumes a 25pF load on TDO. Output timing derates at 0.072ns/pF of extra load applied.
3.
TDO enable time applies when the TAP controller enters the Shift-DR or Shift-IR states.
4.
TDO disable time applies when the TAP controller leaves the Shift-DR or Shift-IR states.
5.
For correct data latching, the I/O signals (from the core and the pads) must be setup and held with
respect to the rising edge of TCK in the CAPTURE-DR state of the SAMPLE/PRELOAD, INTEST
and EXTEST instructions.
6.
Assumes that the data outputs are loaded with the AC test loads (see AC parameter specification).
7.
Data output enable time applies when the boundary scan logic is used to enable the output drivers.
8.
Data output disable time applies when the boundary scan is used to disable the output drivers.
9.
TMS must be held high as nTRST is taken high at the end of the boundary-scan reset sequence.
98
Output enable
Type
BS Cell
Guard
Value
IN EX *
Pin
49
din24
D[24]
IN
-
*
1
din0
D[0]
IN
-
*
0
50
dout24
D[24]
OUT
Nenout=0
0
*
2
dout0
D[0]
OUT
Nenout=0
0
*
51
din25
D[25]
IN
-
*
0
3
din1
D[1]
IN
-
*
0
52
dout25
D[25]
OUT
Nenout=0
0
*
4
dout1
D[1]
OUT
Nenout=0
0
*
53
din26
D[26]
IN
-
*
0
5
din2
D[2]
IN
-
*
0
54
dout26
D[26]
OUT
Nenout=0
0
*
6
dout2
D[2]
OUT
Nenout=0
0
*
55
din27
D[27]
IN
-
*
0
7
din3
D[3]
IN
-
*
0
56
dout27
D[27]
OUT
Nenout=0
0
*
8
dout3
D[3]
OUT
Nenout=0
0
*
57
din28
D[28]
IN
-
*
0
9
din4
D[4]
IN
-
*
0
58
dout28
D[28]
OUT
Nenout=0
0
*
10
dout4
D[4]
OUT
Nenout=0
0
*
59
din29
D[29]
IN
-
*
0
11
din5
D[5]
IN
-
*
0
60
dout29
D[29]
OUT
Nenout=0
0
*
12
dout5
D[5]
OUT
Nenout=0
0
*
61
din30
D[30]
IN
-
*
0
13
din6
D[6]
IN
-
*
0
62
dout30
D[30]
OUT
Nenout=0
0
*
14
dout6
D[6]
OUT
Nenout=0
0
*
63
din31
D[31]
IN
-
*
0
15
din7
D[7]
IN
-
*
0
64
dout31
D[31]
OUT
Nenout=0
0
*
16
dout7
D[7]
OUT
Nenout=0
0
*
65
cpa
CPA
IN
-
*
1
17
din8
D[8]
IN
-
*
0
66
Nenout
-
18
dout8
D[8]
OUT
Nenout=0
0
*
67
Nce
19
din9
D[9]
IN
-
*
0
68
lock
20
dout9
D[9]
OUT
Nenout=0
0
*
69
bigend
21
din10
D[10]
IN
-
*
0
70
Ncpi
22
dout10
D[10]
OUT
Nenout=0
0
*
71
dbe
23
din11
D[11]
IN
-
*
0
72
24
dout11
D[11]
OUT
Nenout=0
0
*
73
25
din12
D[12]
IN
-
*
0
74
26
dout12
D[12]
OUT
Nenout=0
0
*
75
27
din13
D[13]
IN
-
*
0
76
28
dout13
D[13]
OUT
Nenout=0
0
*
29
din14
D[14]
IN
-
*
30
dout14
D[14]
OUT
Nenout=0
0
31
din15
D[15]
IN
-
*
32
dout15
D[15]
OUT
Nenout=0
0
33
din16
D[16]
IN
-
*
34
dout16
D[16]
OUT
Nenout=0
0
35
din17
D[17]
IN
-
*
0
84
Nfiq
nFIQ
IN
-
*
1
36
dout17
D[17]
OUT
Nenout=0
0
*
85
Nreset
nRESET
IN
-
*
0
37
din18
D[18]
IN
-
*
0
86
ale
ALE
IN
-
*
1
38
dout18
D[18]
OUT
Nenout=0
0
*
87
cpb
CPB
IN
-
*
1
39
din19
D[19]
IN
-
*
0
88
Ntrans
nTRANS
OUT
Nce=0
0
*
40
dout19
D[19]
OUT
Nenout=0
0
*
89
a31
A[31]
OUT
ABE=1
0
*
41
din20
D[20]
IN
-
*
0
90
a30
A[30]
OUT
ABE=1
0
*
42
dout20
D[20]
OUT
Nenout=0
0
*
91
a29
A[29]
OUT
ABE=1
0
*
43
din21
D[21]
IN
-
*
0
92
a28
A[28]
OUT
ABE=1
0
*
44
dout21
D[21]
OUT
Nenout=0
0
*
93
a27
A[27]
OUT
ABE=1
0
*
45
din22
D[22]
IN
-
*
0
94
a26
A[26]
OUT
ABE=1
0
*
46
dout22
D[22]
OUT
Nenout=0
0
*
95
a25
A[25]
OUT
ABE=1
0
*
47
din23
D[23]
IN
-
*
0
96
a24
A[24]
OUT
ABE=1
0
*
48
dout23
D[23]
OUT
Nenout=0
0
*
97
a23
A[23]
OUT
ABE=1
0
*
from tdi
No.
Pin
Guard
Value
IN EX *
Cell Name
No.
Cell Name
Output enable
Type
BS Cell
0
OUTEN0
-
1
*
OUTEN0
-
1
*
LOCK
OUT
Nce=0
0
*
BIGEND
IN
-
*
0
nCPI
OUT
Nce=0
0
*
DBE
IN
-
*
0
Nbw
nBW
OUT
Nce=0
0
*
mclk
MCLK
IN
-
*
0
Nwait
nWAIT
IN
-
*
0
lateabt
LATEABT
IN
-
*
1
prog32
PROG32
IN
-
*
1
77
data32
DATA32
IN
-
*
1
0
78
Nrw
nRW
OUT
Nce=0
0
*
*
79
Nopc
nOPC
OUT
Nce=0
0
*
0
80
Nmreq
nMREQ
OUT
Nce=0
0
*
*
81
seq
SEQ
OUT
Nce=0
0
*
0
82
abort
ABORT
IN
-
*
0
*
83
Nirq
nIRQ
IN
-
*
1
99
P60ARM-B
Output enable
Type
BS Cell
Guard
Value
IN EX *
Guard
Value
IN EX *
No.
Cell Name
Pin
Output enable
Type
BS Cell
*
111
a09
A[9]
OUT
ABE=1
0
*
*
112
a08
A[8]
OUT
ABE=1
0
*
0
*
113
a07
A[7]
OUT
ABE=1
0
*
ABE=1
0
*
114
a06
A[6]
OUT
ABE=1
0
*
OUT
ABE=1
0
*
115
a05
A[5]
OUT
ABE=1
0
*
A[17]
OUT
ABE=1
0
*
116
a04
A[4]
OUT
ABE=1
0
*
a16
A[16]
OUT
ABE=1
0
*
117
a03
A[3]
OUT
ABE=1
0
*
105
a15
A[15]
OUT
ABE=1
0
*
118
a02
A[2]
OUT
ABE=1
0
*
106
a14
A[14]
OUT
ABE=1
0
*
119
a01
A[1]
OUT
ABE=1
0
*
107
a13
A[13]
OUT
ABE=1
0
*
120
a00
A[0]
OUT
ABE=1
0
*
108
a12
A[12]
OUT
ABE=1
0
*
121
abe
ABE
INEN1
-
0
*
109
a11
A[11]
OUT
ABE=1
0
*
110
a10
A[10]
OUT
ABE=1
0
*
No.
Cell Name
Pin
98
a22
A[22]
OUT
ABE=1
0
99
a21
A[21]
OUT
ABE=1
0
100
a20
A[20]
OUT
ABE=1
101
a19
A[19]
OUT
102
a18
A[18]
103
a17
104
Table 25: Boundary Scan Signals & Pins
Key:
100
IN
Input pad
OUT
Output pad
NEN1
Input enable active high
OUTENO
Output enable active low
*
Guard Value for INTEST and EXTEST/CLAMP
to tdo
DC Parameters
9.0 DC Parameters
9.1 Absolute Maximum Ratings
Symbol
Parameter
Min
Typ
Max
Units
VDD
Supply voltage
0.0
7.0
V
Vip
Voltage applied to input pin
-0.5
7.0
V
Vop
Voltage applied to output pin
-0.5
Vdd+0.3
V
Osct
Output short circuit time
1
S
Ts
Storage temperature
-65
150
deg.C
Ta
Ambient operating temperature
-10
85
deg.C
Pd
Maximum power dissipation
2.0
W
Notes
1
Table 26: ARM60 DC Parameters - maximum ratings
NOTES:
These are stress ratings only. Exceeding the absolute maximum ratings may permanently damage the
device. Operating the device at absolute maximum ratings for extended periods may affect device
reliability. Functional operation of the device at these or any other condition outside those specified is not
implied.
The device contains circuitry designed to provide protection from damage by static discharge. It is
nonetheless recommended that precautions be taken to avoid applying voltages outside the specified
range.
All voltages are measured with respect to VSS.
(1) Not more than one output should be shorted to VDD or VSS at any one time.
101
P60ARM-B
9.2 DC Operating Conditions
Symbol
Parameter
Min
VDD
Supply voltage
4.5
Vih
Input HIGH voltage
Vil
Input LOW voltage
Io4
Typ
5.0
Max
Units
Notes
5.5
V
2.4
VDD
V
1
0.0
0.8
V
1
Output current (O4 outputs)
+/-4
mA
Io8
Output current (OS8 outputs)
+/-8
mA
Ta
Ambient operating temperature
+85
deg.C
-40
Table 27: ARM60-B DC Operating Conditions
Notes:
Voltages measured with respect to VSS.
(1)
Theses levels apply to all inputs of type I and IP. Particular care needs to be taken with clock inputs
in the PCB layout to eliminate EMC noise and provide true supply voltages directly at the device
pins.
9.3 DC Characteristics
Given VDD = 5.0V ± 10%, Ta = 0 to 70°C
Symbol
Parameter
Min
Idd
static Supply current
Ilatch
DC latch-up current
Iin
Input leakage current
Vol
Output LOW voltage
Voh
Output HIGH voltage
2.4
Rp
ÕIPÕ input pullup resistor
35k
Cin
Input capacitance
ESD
HBM model ESD
Typ
Max
1
mA
2
+/-10
µA
3
0.4
V
4
V
4
ohm
5
100
100k
2
Notes
µA
50
5
Units
pF
kV
Table 28: ARM60 DC Characteristics
Notes:
Voltages measured with respect to VSS.
(1)
All IP inputs at VDD.
(2)
This value represents the current that the input/output pins can tolerate before the chip latches up.
As sustained latch-up is catastrophic, this current must never be approached.
102
DC Parameters
(3)
For Vin = 0 to VDD and only for inputs without pullup resistors.
(4)
When sourcing or sinking the maximum rated output current for the output driver ( 4 or 8mA).
(5)
Only certain inputs have pullup resistors.
103
P60ARM-B
104
AC Parameters
10.0 AC Parameters
The AC timing diagrams presented in this section assume that the outputs of the ARM60 have been loaded
with the capacitive loads shown in the `Test Load' column of Table 29: AC Test Loads. These loads have been
chosen as typical of the type of system in which ARM60 might be employed.
The output drivers of the ARM60 are CMOS inverters which exhibit a propagation delay that increases
linearly with the increase in load capacitance. An `Output derating' figure is given for each output driver,
showing the approximate rate of increase of output time with increasing load capacitance.
Test
Load
(pF)
Output
derating
(ns/pF)
D[31:0]
50
0.072
A[31:0]
50
0.072
LOCK
25
0.072
nCPI
25
0.093
nMREQ
25
0.093
SEQ
25
0.093
nRW
25
0.072
nBW
25
0.072
nOPC
25
0.093
nTRANS
25
0.072
TDO
25
0.072
Output
Signal
Table 29: AC Test Loads
105
P60ARM-B
MCLK
A[31:0]
T ah
T addr
nRW
T rwh
nBW,
LOCK
T blh
T rwd
T bld
nTRANS
T mdh
T mdd
nOPC
T opch
nMREQ,
SEQ
T msh
T opcd
T msd
Figure 37: General Timings
Note:
nWAIT, ABE and ALE are all HIGH during the cycle shown.
MCLK
ALE
T ald
A[31:0]
T ale
Figure 38: Address Timing
Note:
106
Tald is the time by which ALE must be driven LOW in order to latch the current address in phase
2. If ALE is driven low after Tald, then a new address may be latched. ABE is high during the cycle
shown.
AC Parameters
MCLK
ABE
A[31:0]
T abz
T abe
T addr
Figure 39: Address Control
Note:
Tabz is the tristate turn off time, Tabe is the address enable time (turn on), relative to ABE. ALE is
high during the cycle shown.
MCLK
D[31:0]
T dout
T doh
Figure 40: Data Write Cycle
Note:
DBE is high during the cycle shown.
MCLK
D[31:0]
T dis
T dih
Figure 41: Data Read Cycle
Note:
DBE is high during the cycle shown.
107
P60ARM-B
MCLK
D[31:0]
T de
T dz
T doh
T dout
DBE
T dbz
T dbe
Figure 42: Data Bus Control
Note:
The cycle shown is a data write cycle. Here, DBE has been used to modify the behaviour of the data
bus.
MCLK
LATEABT,
BIGEND,
DATA32,
PROG32
T cth
T cts
Figure 43: Configuration Pin Timing
MCLK
nCPI
T cpi
T cpih
CPA, CPB
T cps
nMREQ,
SEQ
T cph
T cpms
Figure 44: Coprocessor Timing
Note:
108
Normally, nMREQ and SEQ become valid Tmsd after the falling edge of MCLK. In this cycle the
ARM has been busy-waiting, waiting for a coprocessor to complete the instruction. If CPA and CPB
change during phase 1, the timing of nMREQ and SEQ will depend on Tcpms. Most systems
should be able to generate CPA and CPB during the previous phase 2, and so the timing of nMREQ
and SEQ will always be Tmsd.
AC Parameters
MCLK
ABORT
T abts
T abth
nRESET
T rs
T rh
nFIQ, nIRQ
T irs
T irm
Figure 45: Exception Timing
Note:
Tirs, Trs guarantee recognition of the interrupt (or reset) source by the corresponding clock edge.
Tirm, Trh guarantee non-recognition by that clock edge. These inputs may be applied fully
asynchronously where the exact cycle of recognition is unimportant.
MCLK
T clkl
T clkh
nWAIT
T ws
T wh
ph2
nMREQ/
SEQ
T msd
A[31:0]
T addr
Figure 46: Clock Timing
Note:
The ARM core is not clocked by the HIGH phase of MCLK enveloped by nWAIT. Thus, during the
cycles shown, nMREQ and SEQ change once, during the first LOW phase of MCLK, and A[31:0]
change once, during the second HIGH phase of MCLK. For reference, ph2 is shown. This is the
internal clock from which the core times all its activity. This signal is included to show how the high
phase of the external MCLK has been removed from the internal core clock.
109
P60ARM-B
P60ARM*
Min
Max
Min
Tckl
clock LOW time
23
16
Tckh
clock HIGH time
23
16
Tws
nWAIT setup to CKr
3
3
Twh
nWAIT hold from CKf
3
Tale
address latch open
0
Tald
address latch time
Max
3
15
0
1
14
1
Taddr
CKr to address valid
Tah
address hold time
6
Tdbz
Data bus tristate time from DBE
3
12
3
12
Tdbe
Data bus enable time from DBE
3
13
3
13
Tabz
Address bus disable from ABE
3
12
3
12
Tabe
Address bus enable from ABE
3
13
3
13
Tde
Data bus enable from MCLK
10
Tdz
Data bus disable from MCLK
Tdout
data out delay
Tdoh
data out hold
3
3
Tdis
data in setup
3
2
Tdih
data in hold
6
6
Tabts
ABORT setup time
5
5
Tabth
ABORT hold time
3
3
Trs
RESET Setup time
6
6
Trh
RESET hold time
6
6
Tirs
interrupt setup
6
4
Tirm
Interrupt non-recognition time
6
Trwd
CKr to nRW valid
Trwh
nRW hold time
Tmsd
CKf to nMREQ & SEQ
Tmsh
nMREQ & SEQ hold time
22
20
5
9
10
10
28
4
3
Tbld
CKr to nBW & LOCK
Tblh
nBW & LOCK hold
Tmdd
CKr to nTRANS
Tmdh
nTRANS hold time
22
23
21
3
26
3
22
3
23
3
21
3
23
3
21
3
Topcd
CKr to nOPC valid
Topch
nOPC hold time
3
16
Tcps
CPA, CPB setup
7*
12
Tcph
CPA,CPB hold time
3
3
16
3
Tcpms
CPA, CPB to nMREQ, SEQ
16
16
Tcpi
CKf to nCPI delay
16
16
Tcpih
nCPI hold time
3
3
Tcts
Config setup time
2
2
Tcth
Config hold time
2
2
Table 30: AC Parameters (units of nS)
110
P60ARM-B
Parameter
Symbol
AC Parameters
* Note:
Table 30 also includes data fpr the obsolete P60ARM for convenience. Customers replacing the
P60ARM by the P60ARM-B should check that timing differences betweem the two devices will
not cause operational problems. Note in particular that Tah and Tde are marginally less for the
-B version. In the case of Tcps, the figure of 7 ns for the P60ARM was incorrect. The correct
figure for both processors is 12 ns.
111
P60ARM-B
10.1 Notes on AC Parameters
1.
Tristate output times:
2.
For a valid RESET, NRESET must remain low for a minimum of two MCLK cycles.
112
Physical Details
11.0 Physical Details
17.90 ±0.25
14.00 ±0.10
Pin 100
Pin 81
Pin 1
Pin 80
23.90 ±0.25
20.00 ±0.10
ARM60
Pin 51
Pin 30
Pin 31
Pin 50
2.80 ±0.25
3.40 max
0.65 typ
0.30
0.83 ±0.15
Figure 47: ARM60 100 Pin Metric Plastic QFP Mechanical Dimensions in mm
113
P60ARM-B
114
Pinout
12.0 Pinout
Pin
Signal
Type
Pin
Signal
Type
Pin
Signal
Type
1
D[27]
i/o
41
A[20]
o
81
Vdd
-
2
D[28]
i/o
42
A[19]
o
82
D[8]
i/o
3
D[29]
i/o
43
A[18]
o
83
D[9]
i/o
4
D[30]
i/o
44
A[17]
o
84
D[10]
i/o
5
D[31]
i/o
45
A[16]
o
85
D[11]
i/o
6
CPA
i
46
A[15]
o
86
D[12]
i/o
7
Vss
-
47
A[14]
o
87
D[13]
i/o
8
Vdd
-
48
A[13]
o
88
D[14]
i/o
9
LOCK
o
49
A[12]
o
89
D[15]
i/o
10
BIGEND
i
50
A[11]
o
90
D[16]
i/o
11
nCPI
o
51
Vdd
-
91
D[17]
i/o
12
DBE
i
52
Vss
-
92
D[18]
i/o
13
nBW
o
53
A[10]
o
93
D[19]
i/o
14
MCLK
i
54
A[9]
o
94
D[20]
i/o
15
nWAIT
i
55
A[8]
o
95
D[21]
i/o
16
LATEABT
i
56
A[7]
o
96
D[22]
i/o
17
PROG32
i
57
A[6]
o
97
D[23]
i/o
18
DATA32
i
58
A[5]
o
98
D[24]
i/o
19
nRW
o
59
A[4]
o
99
D[25]
i/o
20
nOPC
o
60
A[3]
o
100
D[26]
i/o
21
nMREQ
o
61
A[2]
o
22
SEQ
o
62
A[1]
o
23
ABORT
i
63
A[0]
o
24
nIRQ
i
64
Vss
-
25
nFIQ
i
65
Vdd
-
26
nRESET
i
66
ABE
i
27
ALE
i
67
TCK
i
28
CPB
i
68
TMS
i
29
nTRANS
o
69
nTRST
i
30
A[31]
o
70
TDI
i
31
A[30]
o
71
TDO
o
32
A[29]
o
72
D[0]
i/o
33
A[28]
o
73
D[1]
i/o
34
A[27]
o
74
D[2]
i/o
35
A[26]
o
75
D[3]
i/o
36
A[25]
o
76
D[4]
i/o
37
A[24]
o
77
D[5]
i/o
38
A[23]
o
78
D[6]
i/o
39
A[22]
o
79
D[7]
i/o
40
A[21]
o
80
Vss
-
Table 31: Pinout - ARM60 100 pin Plastic Quad Flat Pack
115
For more information about all Zarlink products
visit our Web Site at
www.zarlink.com
Information relating to products and services furnished herein by Zarlink Semiconductor Inc. or its subsidiaries (collectively “Zarlink”) is believed to be reliable.
However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such
information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or
use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual
property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in
certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink.
This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part
of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other
information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the
capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute
any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully determine the performance and
suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does
not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in
significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink’s conditions of sale which are available on request.
Purchase of Zarlink’s I2C components conveys a licence under the Philips I2C Patent rights to use these components in and I2C System, provided that the system
conforms to the I2C Standard Specification as defined by Philips.
Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc.
Copyright Zarlink Semiconductor Inc. All Rights Reserved.
TECHNICAL DOCUMENTATION - NOT FOR RESALE