ILA8842 I2C BUS CONTROLLED SINGLE CHIP TV-RECEIVER FEATURES • • • • • • • • • • • • • • • • • • • • The following features are available: Multi-standard vision IF circuit with an alignment-free PLL demodulator without external components Alignment-free multi-standard FM sound demodulator (4.5 MHz to 6.5 MHz) Audio switch Automatic Volume Limiting Flexible source selection with CVBS switch and Y(CVBS)/C input so that a comb filter can be applied Integrated chrominance trap circuit Integrated luminance delay line Asymmetrical peaking in the luminance channel with a (defeatable) noise coring function PAL/SECAM/NTSC decoder Base-band delay line for PAL and SECAM or chroma comb filter for NTSC Black stretching of non-standard CVBS or luminance signals Integrated chroma band-pass filter with switchable centre frequency Dynamic skin tone control circuit Blue stretch circuit which offsets colours near white towards blue RGB control circuit with "Continuous Cathode Calibration" and white point adjustment Possibility to insert a "blue back" option when no video signal is available Horizontal synchronization with two control loops and alignment-free horizontal oscillator Vertical count-down circuit Vertical driver optimised for DC-coupled vertical output stages I2C-bus control of various functions GENERAL DESCRIPTION The ILA 8842 is I2C-bus controlled single chip TV processor which is intended to be applied in PAL, NTSC, PAL/NTSC and multi-standard television receivers. QUICK REFERENCE DATA SYMBOL Supply VP IP Input voltages ViVIFrms) ViSIF(rms) ViAUDIO(rms) ViCVBS(p-p) ViCHROMA(pp) ViRGB(p-p) Output signals VoCVBS(p-p) PARAMETER MIN. TYP. MAX. supply voltage supply current - 8.0 110 - V mA video IF amplifier sensitivity (RMS value) sound IF amplifier sensitivity (RMS value) external audio input (RMS value) external CVBS/Y input (peak-to-peak value) external chroma input voltage (burst amplitude) (peak-to-peak value) RGB inputs (peak-to-peak value) - 35 1.0 350 1.0 - µV mV mV V - 0.3 - V - 0.7 - V demodulated CVBS output (peak-to-peak value) - 2.2 - V 1 UNIT ILA8842 IoTUNER VoVIDSW(p-p) VoB-Y(p-p) VoR-Y(p-p) VoY(p-p) VoRGB(p-p) IoHOR IoVERT tuner AGC output current range CVBS1/CVBS2 output voltage of video switch (peak-to-peak value) -(R-Y) output/input voltage (peak-to-peak value) -(B-Y) output/input voltage (peak-to-peak value) Y output/input voltage (peak-to-peak value) RGB output signal amplitudes (peak-topeak value) horizontal output current vertical output current (peak-to-peak value) 2 0 - 5 - mA V - 2.0/ 1.0 1.05 - V - 1.33 - V - 1.4 - V - 2.0 - V 10 - 1 - mA mA ILA8842 PINNING SYMBOL SNDIF AUDIOEXT NC NC PLLLF IFVO SCL SDA DECBG CHROMA CVBS/Y VP1 CVBSINT GND1 AUDIOOUT SECPLL CVBSEXT BLKIN BO GO RO BCLIN RI GI BI RGBIN LUMIN LUMOUT BYO RYO BYI RYI REFO XTAL1 XTAL2 DET VP2 CVBS1O DECDIG HOUT FBISO PH2LF PH1LF GND2 AVL VDRB VDRA IFIN1 IFIN2 EHTO VSC Iref DECAGC AGCOUT AUDEEM DECSDEM PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 DESCRIPTION Sound IF input External audio input not connected not connected IF-PLL loop filter IF video output serial clock input serial data input/output bandgap decoupling chrominance input (S-VHS) external CVBS/Y input main supply voltage (+8 V) internal CVBS input ground 1 audio output SECAM PLL decoupling external CVBS input black-current input blue output green output red output beam current limiter input/V-guard input red input for insertion green input for insertion blue input for insertion RGB insertion input not connected luminance output (B-Y) signal output (R-Y) signal output (B-Y) signal input (not available) (R-Y) signal input (not available) subcarrier reference output 3.58 MHz crystal connection 4.43/3.58 MHz crystal connection loop filter phase detector 2nd supply voltage (+8 V) CVBS-1 output Decoupling digital supply horizontal output flyback input/sandcastle output phase-2 filter phase-1 filter ground 2 AVL capacitor vertical drive B output vertical drive A output IF input 1 IF input 2 EHT/overvoltage protection input vertical sawtooth capacitor reference current input AGC decoupling capacitor tuner AGC output Audio deemphasis Decoupling sound demodulator 3 ILA8842 Start-up procedure Read the status bytes until POR = 0 and send all subaddress bytes. The horizontal output signal is switched-on when the oscillator is calibrated. Each time before the data in the IC is refreshed, the status bytes must be read. If POR = 1, the procedure mentioned above must be carried out to restart the IC. When this procedure is not followed the horizontal frequency may be incorrect after power-up or after a power dip. Valid subaddresses: 00 to 1A (subaddresses 04 to 07 and 17 are not used), subaddress FE is reserved for test purposes.Auto-increment mode available for subaddresses. Table 1 Input status bits. FUNCTION Control 0 Control 1 SUB ADDRE SS (HEX) 00 01 DATA BYTE D7 D6 Hue Horizontal shift (HS) Vertical slope (VS) 02 03 08 Vertical amplitude (VA) S-correction (SC) Vertical shift (VSH) White point R White point G White point B Peaking Brightness Saturation Contrast AGC take-over 09 0A 0B 0C 0D 0E 0F 10 11 12 13 Volume control Adjustment IF-PLL Control 2 Control 3 Control 4 14 15 18 19 1A INA FOR F AVL VIM NCI N VID 0 SBL 0 0 MAT 0 RBL IE1 AFW MO D SM IFA OSO HOB 0 Control 5 1B 0 D5 D4 D3 D2 D1 D0 INB FOR S AKB GAI STM INC DL BCO STB FOA POC FOB CM2 XA CM1 A5 A5 A5 A4 A4 A4 A3 A3 A3 A2 A2 A2 A1 A1 A1 XB CM 0 A0 A0 A0 LBM EVG PRD 0 0 0 0 COR 0 IFS VS W FAV IFB VSD BPS 0 A5 A5 A5 A5 A5 A5 A5 A5 A5 A5 A5 A4 A4 A4 A4 A4 A4 A4 A4 A4 A4 A4 A3 A3 A3 A3 A3 A3 A3 A3 A3 A3 A3 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A0 A0 A0 A0 A0 A0 A0 A0 A0 A0 A0 A5 IFC CB ACL 0 A4 0 BLS CMB 0 A3 0 BKS AST 0 A2 0 0 CL2 0 A1 0 0 CL1 FFI 0 0 0 0 0 0 A0 0 BB CL0 EB S FC O 4 ILA8842 Table 2 Output status bits. FUNCTION Output status bytes SUB ADDRE SS (HEX) 00 DATA BYTE D7 D6 D5 D4 D3 D2 D1 D0 CD 0 SX B ID0 POR FSI X SL XPR CD2 CD1 01 NDF IN1 X IFI AFA AFB SXA 02 N2 X BCF IVW ID3 ID2 ID1 min Typ. 7,2 - 8 70 60 1040 10 35 100 µV fi = 45.75 MHz 10 35 100 µV fi = 58.75 MHz 10 35 100 µV Table 3 Characteristics Parameter CONDITIONS Supplies POWER SUPPLY (PINS 12 AND 37) supply voltage supply current pin 12 supply current pin 37 total power dissipation IF circuit VISION IF AMPLIFIER INPUTS (PINS 48 AND 49) input sensitivity (RMS value) fi = 38.90 MHz input resistance (differential) input capacitance (differential) gain control range 64 maximum input signal (RMS value) 150 PLL DEMODULATOR (PLL FILTER ON PIN 5); Free-running frequency of VCO PLL not locked, -500 deviation from nominal setting Catching range PLL Acquisition time PLL VIDEO AMPLIFIER OUTPUT (PIN 6); negative modulation; positive modulation; top sync level negative modulation white level positive modulation Difference in amplitude between negative and positive modulation video output impedance Internal bias current of NPN emitter follower output transistor zero signal output level 5 2 3 75 - max unit 8,8 - - V mA mA mW k pF dB mV +500 kHz 2 - MHz - - 20 ms 1,8 - 4,2 2,2 1,9 4,4 0 2 15 V V V V % 1 50 - - mA ILA8842 maximum source current Bandwidth of demodulated output signal at -3 dB 6 Differential gain Differential phase video non-linearity white spot clamp level noise inverter clamping level noise inverter insertion level (identical to black level) Intermodulation Blue Vo = 0.92 or 1.1 60 MHz Vo = 2.66 or 3.3 60 MHz Yellow Vo = 0.92 or 1.1 56 MHz Vo = 2.66 or 3.3 60 MHz signal-to-noise ratio Weighted 56 Unweighted 49 Residual carrier signal Residual 2nd harmonic of carrier signal IF AND TUNER AGC; Timing of IF-AGC with a 2.2 µF capacitor (pin 53) Modulated video interference 30% AM for 1 mV to 100 mV; 0 to 200 Hz (system B/G) Response time to IF input signal amplitude positive and increase of 52 dB negative modulation Response to an IF input signal amplitude negative modulation decrease of 52 dB positive modulation allowed leakage current of the AGC capacitor negative modulation positive modulation Tuner take-over adjustment (via I2C-bus) minimum starting level for tuner take-over (RMS value) maximum starting level for tuner take-over (RMS 40 value) Tuner control output (pin 54) maximum tuner AGC output voltage maximum tuner gain; output saturation voltage Minimum tuner gain; IO = 2 mA maximum tuner AGC output swing 5 leakage current RF AGC input signal variation for complete tuner control 0,5 AFC OUTPUT (VIA I2C-BUS); AFC resolution window sensitivity window sensitivity in large window mode VIDEO IDENTIFICATION OUTPUT (VIA I2C-BUS) 6 9 2 6 1,5 2,7 5 5 5 5 - mA MHz % deg % V V V 66 - dB 66 - DB 62 - dB 66 - dB 60 53 5,5 2,5 - dB dB mV mV - 10 % 2 - ms 50 - ms 100 - ms 10 µA 200 nA 0,2 0,8 mV 60 - - mV 9 V 300 mV 2 1 4 mA µA dB 2 125 275 - bits kHz kHz ILA8842 delay time of identification after the AGC has stabilized on a new transmitter Sound circuit DEMODULATOR INPUT; (PIN 1) input limiting for PLL catching range (RMS value) Catching range PLL input resistance input capacitance AM rejection VI = 50 mV RMS; DE-EMPHASIS (PIN 55) output signal amplitude (RMS value) output resistance DC output voltage AUDIO OUTPUT (PIN 15) Controlled output signal amplitude (RMS value) -6 dB; output resistance DC output voltage total harmonic distortion - - 10 ms 4,2 60 1 8,5 66 2 6,8 5 - mV MHz k pF dB - 500 15 3 - mV k V 500 - 700 500 3 0,15 900 mV V 0,5 % total harmonic distortion FAV = 1; power supply rejection Internal signal-to-noise ratio External signal-to-noise ratio output level variation with temperature control range Suppression of output signal when mute is active DC shift of the output when mute is active EXTERNAL AUDIO INPUT; (PIN 2) input signal amplitude (RMS value) input resistance voltage gain difference between input and output maximum volume Crosstalk between internal and external audio 60 signals AUTOMATIC VOLUME LEVELLING; CAPACITOR CONNECTED TO PIN 45; gain at maximum boost gain at minimum boost charge (attack) current Discharge (decay) current control voltage at maximum boost control voltage at minimum boost CVBS, Y/C, RGB, CD AND LUMINANCE OUT- AND INPUTS CVBS-Y/C SWITCH, PINS 10, 11, 13, 17 AND 38 CVBS or Y input voltage (peak-to-peak value) - 0,15 25 60 80 80 80 50 0,5 tbf 100 % dB dB dB dB dB dB mV 500 25 9 - 2000 - mV k dB dB 6 -14 1 200 1 5 - dB dB mA nA V V CVBS or Y input current suppression of non-selected CVBS input signal chrominance input voltage (burst amplitude) chrominance input impedance output signal amplitude (CVBS1) (peak-to-peak value) black level of CVBS1 output impedance RGB INPUTS, PINS 23 TO 25 50 - 4 0,3 50 2 - 2,1 - 7 1 1,4 V 1 - µA dB V k V V 250 ILA8842 input signal amplitude for an output signal of 2 V 0,7 0,8 (black-to-white) (peak-to-peak value) input signal amplitude before clipping occurs 1 (peak-to-peak value) difference between black level of internal and 20 external signals at the outputs input currents no clamping; 0,1 1 delay difference for the three channels 0 20 FAST BLANKING, PIN 26 input voltage no data insertion 0,4 data insertion 0,9 0,6 maximum input pulse insertion 3 delay time from RGB in to RGB out data insertion; 60 delay difference between insertion to RGB out and data insertion; 20 RGB in to RGB out input current 0,2 suppression of internal RGB signals insertion; fi = 0 to 5 55 MHz suppression of external RGB signals no insertion; fi = 0 to 55 5 MHz input voltage to blank the RGB outputs to facilitate only on pin 26 (pin 4 `On Screen Display' signals being applied to the 38 for the ILA 885X) outputs COLOUR DIFFERENCE OUTPUT AND INPUT SIGNALS (PINS 29, 30, 31 AND 32); signal amplitude (R-Y) (peak-to-peak value) 1,05 signal amplitude (B-Y) (peak-to-peak value) 1,33 LUMINANCE INPUTS AND OUTPUTS (PIN 28); output signal amplitude (peak-to-peak value) top sync-white 1,4 top sync level 2 output impedance 250 Chrominance filters CHROMINANCE TRAP CIRCUIT; trap frequency fosc Bandwidth at fSC = 3.58 MHz -3 dB 2,8 Bandwidth at fSC = 4.43 MHz -3 dB 3,4 colour subcarrier rejection at nominal peaking 20 30 trap frequency during SECAM 4,3 CHROMINANCE BANDPASS CIRCUIT centre frequency (CB = 0) fosc centre frequency (CB = 1) 1,1xfo MHz sc bandpass quality factor 3 CLOCHE FILTER centre frequency 4,26 4,29 4,31 Bandwidth 241 268 295 LUMINANCE PROCESSING Y DELAY LINE delay time 480 bandwidth of internal delay line 8 PEAKING CONTROL; width of preshoot or overshoot 160 - 8 V V mV µA ns V V V ns ns mA dB dB V V V V V MHz MHz MHz dB MHz MHz MHz kHz ns MHz ns ILA8842 peaking signal compression threshold overshoot at maximum peaking Ratio negative/positive overshoot peaking control curve positive negative - 50 45 80 1,8 - IRE % % - 15 - IRE 63 steps CORING STAGE coring range BLACK LEVEL STRETCHER; Maximum black level shift 15 21 27 IRE level shift at 100% peak white -1 0 1 IRE level shift at 50% peak white -1 3 IRE level shift at 15% peak white 6 8 10 IRE Horizontal and vertical synchronization and drive circuits SYNC VIDEO INPUT (PINS 11, 13 AND 17) sync pulse amplitude 50 300 350 mV slicing level for horizontal sync 50 % slicing level for vertical sync 30 % HORIZONTAL OSCILLATOR free running frequency 15625 Hz spread on free running frequency ±2 % frequency variation with respect to the supply VP = 8.0 V ±10%; 0,3 0,5 % voltage frequency variation with temperature Tamb = 0 to 70°C; 100 Hz FIRST CONTROL LOOP (FILTER CONNECTED TO PIN 43); holding range PLL ±0,9 ±1,2 kHz catching range PLL ±0,6 ±0,9 kHz signal-to-noise ratio of the video input signal at 20 dB which the time constant is switched hysteresis at the switching point 3 dB SECOND CONTROL LOOP (CAPACITOR CONNECTED TO PIN 42) control sensitivity 120 µs/µs control range from start of horizontal output to 19 µs flyback at nominal shift position horizontal shift range 63 steps ±2 µs control sensitivity for dynamic compensation 7,6 µs/V Voltage to switch-on the "flash" protection 6 V Input current during protection 1 mA HORIZONTAL OUTPUT (PIN 40); LOW level output voltage IO = 10 mA 0,4 tbf V maximum allowed output current maximum allowed output voltage duty factor frequency during switch-on and switch-off duty factor during switch-on and switch-off switch-on time switch-off time with RGB drive maximum VOUT = HIGH, switch-off time with RGB drive minimum FLYBACK PULSE INPUT AND SANDCASTLE OUTPUT (PIN 41) required input current during flyback pulse output voltage during burst key 9 10 - 45 2xfH 72 100 100/8 0 60 100 4,8 5,3 VP - mA V % - ms % ms ms 300 µA 5,8 V ILA8842 during blanking 1,9 2,6 2,1 3 2,3 V 3,4 V burst key pulse vertical blanking 3,3 5,2 3,5 14 5,4 3,7 µs lines 5,6 µs clamped input voltage during flyback pulse width delay of start of burst key to start of sync VERTICAL OSCILLATOR; free running frequency locking range divider value not locked locking range VERTICAL RAMP GENERATOR (PIN 51 AND 52) sawtooth amplitude (peak-to-peak value) VS = 1FH; C = 100 nF; R = 39 k discharge current charge current set by external resistor vertical slope control range (63 steps) charge current increase f = 60 Hz LOW level of ramp VERTICAL DRIVE OUTPUTS (PINS 46 AND 47) differential output current (peak-to-peak value) VA = 1FH common mode current output voltage range EHT TRACKING/OVERVOLTAGE PROTECTION (PIN 50) input voltage scan modulation range vertical sensitivity overvoltage detection level DE-INTERLACE first field delay VERTICAL AMPLITUDE control range 63 steps; SC = 00H equivalent differential vertical drive output current SC = 00H (peak-to-peak value) VERTICAL SHIFT control range 63 steps equivalent differential vertical drive output current (peak-to-peak value) S-CORRECTION control range 63 steps Colour demodulation part CHROMINANCE AMPLIFIER ACC control range change in amplitude of the output signals over the ACC range threshold colour killer ON 10 45 50/60 Hz 64,5/7 Hz 2 625/5 lines 25 434/4 722 lines/f 88 rame - 3 - V -20 0,9 16 - - 19 2,3 - % V 0 0,95 400 - 4 mA µA V 1,2 -5 - 6,3 3,9 2,8 +5 - V % %/V V - 0,5H - 80 760 - 120 % 1140 µA -5 -50 - +5 % +50 µA 0 - 30 % 26 - - 2 dB dB -30 - - dB mA µA +20 % ILA8842 hysteresis colour killer OFF strong signal conditions; S/N>40 dB; noisy input signals; ACL CIRCUIT; chrominance burst ratio at which the ACL starts to operate REFERENCE PART Phase-locked loop; catching range phase shift for a ±400 Hz deviation of the oscillator frequency Oscillator temperature coefficient of the oscillator frequency oscillator frequency deviation with respect to the VP = 8 V ±10% supply minimum negative resistance maximum load capacitance HUE CONTROL hue control range 63 steps; hue variation for ±10% VP hue variation with temperature Tamb = 0 to 70 °C; DEMODULATORS (PINS 29 AND 30) General (R-Y) output signal amplitude (peak-to-peak value) (B-Y) output signal amplitude (peak-to-peak value) spread of signal amplitude ratio between standards output impedance (R-Y)/(B-Y) output bandwidth of demodulators -3 dB; PAL/NTSC demodulator gain between both demodulators G(B-Y) and G(RY) residual carrier output (peak-to-peak value); only f = fosc; (R-Y) output valid for PAL and NTSC signals f = fosc; (B-Y) output f = 2fosc; (R-Y) output f = 2fosc; (B-Y) output H/2 ripple at (R-Y) output (peak-to-peak value) change of output signal amplitude with temperature change of output signal amplitude with supply voltage phase error in the demodulated signals SECAM demodulator black level off-set pole frequency of deemphasis ratio pole and zero frequency non linearity calibration voltage pin 16 Base-band delay line 11 - +3 - dB - +1 - dB - 3 - ±360 ±600 - 2 Hz deg - - 1 25 Hz/K Hz - - 1 15 k pF ±35 - ±40 0 0 - deg deg deg -1,5 1,05 1,33 - - 500 650 - 1,6 1,78 1,96 - - 10 10 10 mV mV mV - - 10 mV - 0,1 25 - mV %/K - - - - ±8 deg 77 3 85 3 4 7 93 3 5 kHz kHz V V 1,5 dB kHz ±0,2 dB % V ILA8842 variation of output signal for adjacent time -0,1 0,1 samples at constant input signals residual clock signal (peak-to-peak value) 5 delay of delayed signal 63,94 64 64,06 delay of non-delayed signal 40 60 80 difference in output amplitude with delay on or off 5 COLOUR DIFFERENCE MATRICES (IN CONTROL CIRCUIT) PAL/SECAM mode; ratio of demodulated signals ±10% -0,51 ratio of demodulated signals ±25% -0,19 NTSC mode; the matrix results in the following signals (nominal hue setting) (B-Y) signal: 2.03/0° 2.03UR -0.14UR + 1.58VR (R-Y) signal: 1.59/95° -0.31UR - 0.53VR (G-Y) signal: 0.61/240° REFERENCE SIGNAL OUTPUT PIN 33; reference frequency 3,58/4 ,43 output signal amplitude (peak-to-peak value) 0,2 0,25 0,3 output level to enable the comb filter 4 4,2 5 output level to disable the comb filter 0,1 1,4 Control part SATURATION CONTROL Saturation control range 63 syeps 52 CONTRAST CONTROL; contrast control range 63 steps tracking between the three channels over a control range of 10 dB BRIGHTNESS CONTROL brightness control range 63 steps; RGB AMPLIFIERS (PINS 19, 20 AND 21) output signal amplitude (peak-to-peak value) at nominal tbf luminance input signal, nominal contrast and whitepoint adjustment; maximum signal amplitude (black-to-white) input signal amplitude (Y-input, pin 28) at which the soft clipping is activated output signal amplitude for the `red' channel at nominal settings tbf (peak-to-peak value) for contrast and saturation control and no luminance signal to the input (R-Y, PAL) nominal black level voltage black level voltage when black level stabilisation is switched-off (via AKB bit) black level voltage control range VSD bit active; 1,8 12 18 - - dB mV µs ns % MHz V V V dB dB 0,5 dB ±0,7 - V 2 tbf V tbf tbf - V V 2,1 tbf V 2,4 2,5 - V V 2,5 3,2 V ILA8842 width of video blanking with HBL bit active control range of the black-current stabilisation blanking level 14,4 difference with black level level during leakage measurement level during "low" measuring pulse level during "high" measuring pulse adjustment range of the ratio between the amplitudes of the RGB drive voltage and the measuring pulses variation of black level with temperature relative variation in black level between the three channels during variations of supply voltage (±10%) nominal controls saturation (50 dB) nominal contrast contrast (20 dB) nominal saturation brightness (±0.5 V) nominal controls temperature (range 40 °C) signal-to-noise ratio of the output signals RGB input; 60 CVBS input; 50 residual voltage at the RGB outputs (peak-to-peak at fosc value) at 2fosc plus higher harmonics bandwidth of output signals RGB input; at -3 dB 9 CVBS input; at -3 dB; fosc = 3.58 MHz CVBS input; at -3 dB; fosc = 4.43 MHz S-VHS input; at -3 6 dB WHITE-POINT ADJUSTMENT I2C-bus setting for nominal gain HEX code adjustment range of RGB drive levels gain control range to compensate spreads in picture tube characteristics 2-POINT BLACK-CURRENT STABILISATION (PIN 18); amplitude of "low" reference current amplitude of "high" reference current acceptable leakage current maximum current during scan input impedance BEAM CURRENT LIMITING (PIN 22); contrast reduction starting voltage voltage difference for full contrast reduction brightness reduction starting voltage voltage difference for full brightness reduction internal bias voltage detection level vertical guard minimum input current to activate the guard circuit maximum allowable current - 13 14,7 ±1 -0,5 15 - µs V V -0,1 0,25 0,38 ±3 - V V V dB 1 - mV/K - tbf tbf tbf tbf tbf 15 15 mV mV mV mV mV dB dB mV mV 2,8 - MHz MHz 3,5 - MHz - - MHz 20H ±3 ±6 - dB dB 8 20 ±100 tbf tbf - µA µA µA mA 3 1,8 1,9 1 3,3 3,65 100 1 - V V V V V V µA mA ILA8842 BLUE STRETCH; Decrease of small signal gain for the red and BLS = 1 green channel Decrease of small signal gain for the red channel EBS = 1 Decrease of small signal gain for the green EBS = 1 channel I2C-BUS CONTROL INPUT/OUTPUT (SDA/SCL) input voltage level low-level input voltage high-level input voltage low-level input current Vi = 0 V high-level input current Vi = 5.5 V low-level output voltage SDA, IL = 3 mA 14 - 14 - % - 22 8 - % % 0 3,5 - - 5,5 1,5 -10 10 0,4 V V V µA µA V