RFM HO1065

HO1065
•
•
•
SAW Frequency Stabilization
Fundamental-Mode Oscillation at 400.0 MHz
0.8” x 0.5” x 0.25” Metal Dip Case
400.0 MHz
SAW
Oscillator
This general-purpose oscillator is stabilized by surface-acoustic-wave (SAW) technology. Fundamental oscillation at 400.0 MHz eliminates all internally generated spurious outputs except integral harmonics of 400.0
MHz. The compact size of the rugged, metal, hermetically-sealed case makes this oscillator suitable for a variety of applications.
Absolute Maximum Ratings
Rating
DC Supply Voltage
Ambient Temperature
Value
Units
0 to +13
VDC
Powered
-40 to +70
Storage
-40 to +85
Dip 14-8 Case
°C
Electrical Characteristics
Characteristic
Operating Frequency
Absolute Frequency
Tolerance from 400.0 MHz
RF Output Power
Spurious Outputs
Sym
fO
∆fO
PO
Nonharmonic
Nominal Impedance
Operating Load VSWR
DC Power Supply
1, 7
Minimum
Typical
400
399.800
Maximum
Units
400.200
MHz
±200
3, 6
+10
+13
-15
3, 6, 7
ZO
3
ΓL
3, 5
Operating Voltage
VCC
Operating Current
ICC
Operating Ambient Temperature
kHz
dBm
Second Harmonics
Third and Higher Harmonics
RF Impedance
Notes
TA
3, 6
3, 6
Lid Symbolization (YY=Year, WW=Week)
-20
-60
<-80
50
10.8
dBc
Ω
12.0
1.5:1
13.2
VDC
40
50
mA
+70
°C
-40
RFM HO1065 YYWW
BLOCK DIAGRAM
CAUTION: Electrostatic Sensitive Device. Observe precautions for
handling. COCOM CAUTION: Approval by the U.S. Department
of Commerce is required prior to export of this device.
V CC
Notes:
1.
2.
3.
4.
5.
6.
7.
One or more of the following United States patents apply: 4,616,197; 4,610,681; and
4,761,616.
Unless noted otherwise, all specifications are listed at TA = +25°C ±2°C, VCC = nominal voltage ±0.01 VDC, and load impedance = 50 Ω with VSWR ≤ 1.5:1.
The design, manufacturing process, and specifications of this device are subject to
change without notice.
Applies to oscillator only and not to sidebands caused by external electrical or
mechanical sources. (Dedicated external voltage regulation with low-frequency filtering for the DC power supply and proper circuit board layout are recommended for
optimum spectral purity.)
For specified maximum operating load VSWR (any angle) at FO. (No instability or
damage will occur for any passive load impedance.)
For any combination of VCC and TA within the specified operating ranges.
Applies for any combination of Note 5 and 6 conditions.
RF Monolithics, Inc.
Phone: (972) 233-2903
Fax: (972) 387-9148
RFM Europe
Phone: 44 1963 251383
Fax: 44 1963 251510
©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc.
RF OUTPUT
SAW Oscillator
Buffer Amplifier
ELECTRICAL CONNECTIONS
VCC 1
Case Ground 2
CC
13 Case Ground
Top
View
Case Ground 6
RF Output 7
9 Case Ground
8 VCC
E-mail: [email protected]
http://www.rfm.com
HO1065-101599
Page 1 of 2
400.0 MHz
DIP14-8
SAW Oscillator
Metal Dual-Inline Package with 8 leads in a 14-lead DIP configuration
mm
Inches
Dimension
Top View
MIN
MAX
MIN
MAX
A
—
20.45
—
0.805
B
—
12.83
—
0.505
C
—
6.35
—
0.250
D
0.40
0.51
0.016
0.020
E
0.64 Nominal
0.025 Nominal
F
7.62 Nominal
0.300 Nominal
G
2.54 Nominal
0.100 Nominal
H
15.24 Nominal
0.600 Nominal
K
5.97
6.73
0.235
0.265
L
1.30
—
0.051
—
M
—
11.18
—
0.440
N
—
18.80
—
0.740
R
1.75
2.26
0.069
0.089
Bottom View
C
B
M
K
F
(4 Places)
R
L
(3 Places)
7
6
A
8
9
H
N
2
1
D
Pin 1 Mark
(Optional)
E
13
14
G
(4 Places)
(8 Places)
RF Monolithics, Inc.
Phone: (972) 233-2903
Fax: (972) 387-9148
RFM Europe
Phone: 44 1963 251383
Fax: 44 1963 251510
©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc.
E-mail: [email protected]
http://www.rfm.com
HO1065-101599
Page 2 of 2