RFM HO4002-1

Preliminary
HO4002-1
®
•
•
•
SAW Frequency Stabilization
Fundamental-Mode Oscillation at 400.0 MHz
A Rugged, Compact General-Purpose Oscillator
400.0 MHz
SAW
Oscillator
The frequency of this oscillator is stabilized by surface-acoustic-wave (SAW) technology. This results in excellent performance from a compact, rugged, oscillator operating at the fundamental frequency of 400.0 MHz.
The high-reliability of the HO4002-1 makes it suitable for general purpose use in a wide variety of applications.
Absolute Maximum Ratings
Rating
DC Supply Voltage
Case Temperature
Value
Units
0 to +13
VDC
Powered
-40 to +70
Storage
-40 to +85
Dip 16-8 Case
°C
Electrical Characteristics
Characteristic
Operating Frequency
AbsoluteFrequency
Sym
Notes
fO
1, 7
Minimum
Tune Range
399.960
Tune Voltage
0
Typical
400.00
Discrete Spurious
Units
400.040
MHz
+10
VDC
3:1
Tuning Linearity
RF Output Power
Maximum
PO
Second Harmonics
3, 6
+7
4:1
+10
dBm
-15
2, 3, 4
Third and Higher Harmonics
SSB Phase Noise
RF Impedance
DC Power Supply
MHz
Nonharmonic
1 kHz Offset
-80
-100
-95
10 kHz Offset
-130
-125
100 kHz Offset
-150
Nominal Impedance
ZO
3
Operating Load VSWR
GL
3, 5
3, 6
Operating Voltage
VCC
Operating Current
ICC
Operating Case Temperature
dBc
-20
TC
3, 6
Lid Symbolization (YY=Year, WW=Week)
CAUTION: Electrostatic Sensitive Device. Observe precautions for
handling. COCOM CAUTION: Approval by the U.S. Department of
Commerce is required prior to export of this device.
50
10.8
dBc/Hz
Ω
12
-20
2:1
13.2
VDC
45
mA
+70
°C
RFM HO4002-1 YYWW
BLOCK DIAGRAM
V CC
Notes:
1.
2.
3.
4.
5.
6.
7.
One or more of the following United States patents apply: 4,616,197; 4,610,681; and
4,761,616.
Unless noted otherwise, all specifications are listed at TC = +25°C ±2°C, VCC = nominal voltage ±0.01 VDC, and load impedance = 50 Ω with VSWR ≤ 1.5:1.
The design, manufacturing process , and specification of this device are subject to
change without notice.
Applies to oscillator only and not to sidebands caused by external electrical or
mechanical sources. (Dedicated external voltage regulation with low-frequency filtering for the DC power supply and proper circuit board layout are recommended for
optimum spectral purity.)
For specified maximum operating load VSWR (any angle) at FO. (No instability or
damage will occur for any passive load impedance.)
For any combination of VCC and TC within the specified operating ranges.
Applies for any combination of Note 5 and 6 conditions.
RF Monolithics, Inc.
Phone: (972) 233-2903
Fax: (972) 387-8148
RFM Europe
Phone: 44 1963 251383
Fax: 44 1963 251510
©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc.
RF OUTPUT
SAW Oscillator
Buffer Amplifier
ELECTRICAL CONNECTIONS
VCC 1
Case Ground 2
V tune
15 Case Ground
Top
View
Case Ground 7
RF Output 8
10 Case Ground
9 V CC
E-mail: [email protected]
http://www.rfm.com
HO4002-1-043003
Page 1 of 2
400.0 MHz
DIP16-8
SAW Oscillator
Metal Dual-Inline Package with 8 leads in a 16-lead DIP configuration
mm
Inches
Dimension
Top View
MIN
MAX
MIN
MAX
A
—
25.02
—
0.985
B
—
12.83
—
0.505
C
—
6.35
—
0.250
D
0.40
0.51
0.016
0.020
E
0.64 Nominal
0.025 Nominal
F
7.62 Nominal
0.300 Nominal
G
2.54 Nominal
0.100 Nominal
H
17.78 Nominal
0.700 Nominal
K
3,39
6.73
0.130
0.265
L
1.30
—
0.051
—
M
—
11.18
—
0.440
N
—
22.60
—
0.890
R
1.75
2.26
0.069
0.089
Bottom View
C
B
M
K
F
(4 Places)
R
L
(3 Places)
8
7
A
9
10
H
N
2
1
D
Pin 1 Mark
(Optional)
E
15
16
G
(4 Places)
(8 Places)
RF Monolithics, Inc.
Phone: (972) 233-2903
Fax: (972) 387-8148
RFM Europe
Phone: 44 1963 251383
Fax: 44 1963 251510
©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc.
E-mail: [email protected]
http://www.rfm.com
HO4002-1-043003
Page 2 of 2