Preliminary HO4001-1 • • • SAW Frequency Stabilization Fundamental-Mode Oscillation at 1000.0 MHz A Rugged, Compact General-Purpose Oscillator 1000.0 MHz SAW Oscillator The frequency of this oscillator is stabilized by surface-acoustic-wave (SAW) technology. This results in excellent performance from a compact, rugged, oscillator operating at the fundamental frequency of 1000.0 MHz. The highly-reliable HO4001-1 makes it suitable for general purpose use in a wide variety of applications Dip 16-8 Case Characteristic Operating Frequency Absolute Frequency Sym Notes Minimum fO Tune Range 1, 7 Tune Voltage Typical 1000.0 Discrete Spurious 1000.150 MHz 0 +5 VDC DC Power Supply +7 4:1 +10 dBm Second Harmonics 2, 3, 4 -80 1 kHz Offset -100 -95 2, 3, 4 -130 -125 -150 50 100kHz Offset Nominal Impedance ZO 3 Operating Load VSWR GL 3, 5 Operating Voltage VCC 3, 6 Operating Current ICC Operating Ambient Temperature TA 3, 6 Lid Symbolization (YY=Year, WW=Week) dBc -20 Nonharmonic 10 kHz Offset RF Impedance 3, 6 -15 Third and Higher Harmonics SSB Phase Noise MHz 3:1 PO Units 999.850 Tuning Linearity RF Output Power Maximum 4.75 dBc/Hz Ω 5.0 -20 2:1 5.25 VDC 45 mA +70 °C RFM HO4001-1 YYWW BLOCK DIAGRAM CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. COCOM CAUTION: Approval by the U.S. Department of Commerce is required prior to export of this device. V CC Notes: 1. 2. 3. 4. 5. 6. 7. One or more of the following United States patents apply: 4,616,197; 4,610,681; and 4,761,616. Unless noted otherwise, all specifications are listed at TA = +25°C ±2°C, VCC = nominal voltage ±0.01 VDC, and load impedance = 50 Ω with VSWR ≤ 1.5:1. The design, manufacturing process , and specification of this device are subject to change without notice. Applies to oscillator only and not to sidebands caused by external electrical or mechanical sources. (Dedicated external voltage regulation with low-frequency filtering for the DC power supply and proper circuit board layout are recommended for optimum spectral purity.) For specified maximum operating load VSWR (any angle) at FO. (No instability or damage will occur for any passive load impedance.) For any combination of VCC and TA within the specified operating ranges. Applies for any combination of Note 5 and 6 conditions. RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-9148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. RF OUTPUT SAW Oscillator Buffer Amplifier ELECTRICAL CONNECTIONS VCC 1 Case Ground 2 V tune 15 Case Ground Top View Case Ground 7 RF Output 8 E-mail: [email protected] http://www.rfm.com HO4001-1-062001 10 Case Ground 9 VCC Page 1 of 2 1000.0 MHz DIP16-8 SAW Oscillator Metal Dual-Inline Package with 8 leads in a 16-lead DIP configuration mm Inches Dimension Top View MIN MAX MIN MAX A — 25.02 — 0.985 B — 12.83 — 0.505 C — 6.35 — 0.250 D 0.40 0.51 0.016 0.020 E 0.64 Nominal 0.025 Nominal F 7.62 Nominal 0.300 Nominal G 2.54 Nominal 0.100 Nominal H 17.78 Nominal 0.700 Nominal K 3,39 6.73 0.130 0.265 L 1.30 — 0.051 — M — 11.18 — 0.440 N — 22.60 — 0.890 R 1.75 2.26 0.069 0.089 Bottom View C B M K F (4 Places) R L (3 Places) 8 7 A 9 10 H N 2 1 D Pin 1 Mark (Optional) E 15 16 G (4 Places) (8 Places) RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-9148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: [email protected] http://www.rfm.com HO4001-1-062001 Page 2 of 2