Technical Data Sheet Right Angle Lens Chip LEDs with Bi-Color(Multi-Color) 12-22/G6R8C-A30/2C Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Multi-color type. ․Pb-free. ․The product itself will remain within RoHS compliant version. Descriptions ․The 12-22 SMD LED is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. ․Besides, lightweight makes them ideal for miniature applications. etc. Applications ․Backlighting in dashboard and switch. ․Telecommunication: indicator and backlighting in telephone and fax. ․Flat backlight for LCD, switch and symbol. ․General use. Device Selection Guide Chip Emitted Color Type Material G6 AlGaInP Brilliant Yellow Green R8 AlGaInP Deep - Red Resin Color Water Clear Everlight Electronics Co., Ltd. http://www.everlight.com Rev.1 Page: 1 of 12 Device No. Prepared date: 30-Jun-2011 Prepared by: Haizheng Gao 12-22/G6R8C-A30/2C Package Outline Dimensions Note: The tolerances unless mentioned is ±0.1mm,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Rev.1 Page: 2 of 12 Device No. Prepared date: 30-Jun-2011 Prepared by: Haizheng Gao 12-22/G6R8C-A30/2C Absolute Maximum Ratings (Ta=25℃ ℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF Peak Forward Current (Duty 1/10 @1KHz) IFP R8:25 mA G6:25 R8:60 mA G6:60 R8:60 Power Dissipation Pd mW Electrostatic Discharge(HBM) ESD Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +90 ℃ Soldering Temperature Tsol G6:60 R6:2000 V G6:2000 Reflow Soldering : 260 ℃ for 10 sec. Hand Soldering : 350 ℃ for 3 sec. Everlight Electronics Co., Ltd. http://www.everlight.com Rev.1 Page: 3 of 12 Device No. Prepared date: 30-Jun-2011 Prepared by: Haizheng Gao 12-22/G6R8C-A30/2C Electro-Optical Characteristics (Ta=25℃ ℃) Parameter Luminous Intensity Symbol Min. Typ. Max. R8 45.0 ----- 90.0 IV Viewing Angle G6 22.5 ----- 57.0 2θ1/2 ----- 120 ----- deg ----- nm λp 650 ----- G6 R8 Dominant Wavelength 575 ----- ----- △λ 573 ----- R8 IF=20mA ----- 20 G6 nm ----20 1.70 2.00 2.40 V VF G6 1.70 2.00 R6 Reverse Current ----nm R8 Forward Voltage 639 λd G6 Spectrum Radiation Bandwidth Condition mcd R8 Peak Wavelength Unit IR 2.40 10 ----- μA ----- G6 VR=5V 10 Notes: 1.Tolerance of Luminous Intensity ±11% Everlight Electronics Co., Ltd. http://www.everlight.com Rev.1 Page: 4 of 12 Device No. Prepared date: 30-Jun-2011 Prepared by: Haizheng Gao 12-22/G6R8C-A30/2C Bin Range Of Luminous Intensity R8 Bin Min Max P1 45.0 57.0 P2 57.0 72.0 Q1 72.0 90.0 Bin Min Max 1 22.5 36.0 2 36.0 57.0 Unit Condition mcd IF=20mA Unit Condition mcd IF=20mA G6 Notes: 1.Tolerance of Luminous Intensity ±11% Everlight Electronics Co., Ltd. http://www.everlight.com Rev.1 Page: 5 of 12 Device No. Prepared date: 30-Jun-2011 Prepared by: Haizheng Gao 12-22/G6R8C-A30/2C Typical Electro-Optical Characteristics Curves G6 Everlight Electronics Co., Ltd. http://www.everlight.com Rev.1 Page: 6 of 12 Device No. Prepared date: 30-Jun-2011 Prepared by: Haizheng Gao 12-22/G6R8C-A30/2C Typical Electro-Optical Characteristics Curves R8 Everlight Electronics Co., Ltd. http://www.everlight.com Rev.1 Page: 7 of 12 Device No. Prepared date: 30-Jun-2011 Prepared by: Haizheng Gao 12-22/G6R8C-A30/2C Label explanation CAT: Luminous Intensity Rank Pb HUE: Dom. Wavelength Rank CPN : P N : XXXXXXXXXXXXX REF: Forward Voltage Rank XXXXXXXXXXXXX EVERLIGHT RoHS CAT : XXX HUE : XXX REF : XXX QTY : XXX LOT NO : XXXXXXXXXX Reference : XXXXXXXX MADE IN TAIWAN Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm, Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Rev.1 Page: 8 of 12 Device No. Prepared date: 30-Jun-2011 Prepared by: Haizheng Gao 12-22/G6R8C-A30/2C Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel Note: The tolerances unless mentioned is ±0.1mm, Unit = mm Moisture Resistant Packaging Label Aluminum moisture-proof bag Desiccant Label Everlight Electronics Co., Ltd. http://www.everlight.com Rev.1 Page: 9 of 12 Device No. Prepared date: 30-Jun-2011 Prepared by: Haizheng Gao 12-22/G6R8C-A30/2C Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% Test Sample Hours/Cycles Size No. Items Test Condition 1 Reflow Soldering Temp. : 260℃±5℃ Min. 5sec. 6 Min. 22 PCS. 0/1 Temperature Cycle H : +100℃ 15min ∫ 5 min L : -40℃ 15min 300 Cycles 22 PCS. 0/1 Thermal Shock H : +100℃ 5min ∫ 10 sec L : -10℃ 5min 300 Cycles 22 PCS. 0/1 Temp. : 100℃ 1000 Hrs. 22 PCS. 0/1 Temp. : -40℃ 1000 Hrs. 22 PCS. 0/1 2 3 High Temperature Storage Low Temperature Storage 4 5 Ac/Re 6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1 7 High Temperature / High Humidity 85℃/ 85%RH 1000 Hrs. 22 PCS. 0/1 Everlight Electronics Co., Ltd. http://www.everlight.com Rev.1 Page: 10 of 12 Device No. Prepared date: 30-Jun-2011 Prepared by: Haizheng Gao 12-22/G6R8C-A30/2C Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less. If unused LEDs remain, it should be stored in moisture proof packages. 2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. http://www.everlight.com Rev.1 Page: 11 of 12 Device No. Prepared date: 30-Jun-2011 Prepared by: Haizheng Gao 12-22/G6R8C-A30/2C 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com Everlight Electronics Co., Ltd. http://www.everlight.com Rev.1 Page: 12 of 12 Device No. Prepared date: 30-Jun-2011 Prepared by: Haizheng Gao