HD-LINX ™ GO1515 Voltage Controlled Oscillator DATA SHEET DESCRIPTION • generates 1.485GHz or 1.485/1.001GHz signal for HD-LINX™ ICs • Pb-free The GO1515 is a self contained, miniature Voltage Controlled Oscillator (VCO) that is used in conjunction with Gennum’s HD-LINX™ ICs. It produces a clean 1.485GHz reference clock signal for such devices as the GS1515 HDTV Reclocker and other HD-LINX™ devices. The control voltage range is from 3.10 volts to 4.65 volts and is derived from the on-chip PLLs. The GO1515 frequency can be pulled approximately 16MHz for every one volt of control. APPLICATIONS The output level is approximately 1.0dBm with low spurious and noise content. It is designed to drive 50Ω strip lines. • low current consumption • 50Ω output impedance • operates from a single 5V supply • 8 pin tape on reel VCO for the following HD-LINX™ ICs: GS1515, GS1522, GS1540, GS1545. The GO1515 VCO is used with the following HD-LINX™ ICs; GS1515, GS1522, GS1540, GS1545 and is ordered as a separate item. The VCO requires a single 5V supply and draws a maximum of 15mA of current. It is packaged in a miniature 8-pin proprietary surface mount package and operates over the normal commercial temperature range of 0°C to +70°C. ORDERING INFORMATION PART NUMBER PACKAGE TEMPERATURE Pb-FREE GO1515 - CTAE3 8 pin tape on reel 0°C to 70°C Yes VCTR VCC 47pF 1000pF STRIPLINE STRIPLINE 3.3pF 2pF OUT OSCILLATOR CIRCUIT GND BLOCK DIAGRAM Revision Date: July 2005 Document No. 522 - 40 - 04 GENNUM CORPORATION P.O. Box 489, Stn. A, Burlington, Ontario, Canada L7R 3Y3 Tel. +1 (905) 632-2996 Fax. +1 (905) 632-5946 E-mail: [email protected] www.gennum.com GO1515 FEATURES ELECTRICAL CHARACTERISTICS VS = 5.0V ±0.25V, Temperature = 0°C to 70°C unless otherwise specified. PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS VCC 4.75 5.0 5.25 V Supply Current ΙS - - 15 mA Control Voltage Range VCTR +3.1 - +4.65 V Control Voltage Sensitivity df/dV 11 16 21 MHz/V Operating Frequency Range ƒVCO 1483.5 - 1485.5 MHz Output Signal Level VOUT -2 1 +4 dBm Signal to Noise Ratio S/N 40 - - dB 74 - - dBc Signal Level: 1kHz ±8kHz Deviation = 0.3~3.0kHz Carrier to Noise Ratio C/N 25kHz Separation, 1kHz Bandwidth Pushing Figure VS = 5.0V ±0.25V, ref: VS = 5.0V - ±500 - kHz Pulling Figure VSWR = 2.0 for all phase, ref: 50Ω - ±1000 - kHz 0°C to 70°C, ref. = 25°C - - ±3 MHz - - -10 dBc - 50 - Ω Temperature Stability TCOEF Spurious Response Output Impedance ZO PIN CONNECTIONS GND NC GND O/P 7 6 5 GO 1515 8 4 GND TOP VIEW 1 2 3 VCTR GND VCC NOTE: Pin numbers are arbitrary. There are no pin markings on the device itself PIN DESCRIPTIONS NUMBER SYMBOL TYPE DESCRIPTION 2, 4, 6, 8 GND - Most negative power supply connections. 1 VCTR I Control voltage for the VCO. 3 VCC - Most positive power supply connection. 5 O/P O VCO signal output. 7 NC - No connection. 2 of 5 522 - 40 - 04 GO1515 Supply Voltage 65 NC 55 40 GND 55 OUT GND GND 40 VCTR GND 65 GO1515 GO1515 TOP VIEW 45 VCC All dimensions are in mils 1 mil = 1/1000 inch Fig. 1 Footprint of the GO1515 DIMENSIONS NC GND VCTR GND GO1515 TOP VIEW GND OUT GND 4.2 6.0 2.0 ±0.3 ±0.3 MAX VCC 1.6±0.5 2.0 MAX 4.7±0.3 6.3±0.3 All dimensions in millimetres. 7.8 MAX SOLDERING RECOMMENDATIONS Reflow Conditions Soldering Flux The device will meet the data sheet specifications after completing the reflow process according to the profile shown in Figure 3 or Figure 4. Do not reflow the device more than twice. Do not use cleaning type flux. Washing the devices after using cleaning type flux may damage inner parts and affect performance. Endurance To Warp When the device is soldered on a printed circuit board (dimension: 100mm x 100mm; thickness: 1.6mm) and the PCB is warped as shown in Figure 2, the device will not be cracked or damaged. VCO PCB MAX 2mm Fig. 2 PCB Warp 3 of 5 522 - 40 - 04 SOLDER REFLOW PROFILES 60-150 sec. Temperature 10-20 sec. 230˚C 220˚C 3˚C/sec max GO1515 183˚C 6˚C/sec max 150˚C 100˚C 25˚C Time 120 sec. max 6 min. max Fig. 3 Standard Eutectic Solder Reflow Profile Temperature 60-150 sec. 20-40 sec. 260˚C 250˚C 3˚C/sec max 217˚C 6˚C/sec max 200˚C 150˚C 25˚C Time 60-180 sec. max 8 min. max Fig. 4 Maximum Pb-free Solder Reflow Profile 4 of 5 522 - 40 - 04 HANDLING RECOMMENDATIONS Cleaning Do not wash the devices. Storage GO1515 Store the devices out of direct sunlight, at a stable temperature and humidity. Avoid extreme temperatures, high humidity and wide temperature fluctuations. Condensation on the devices may result in reduced quality and lowered solderability. Use within 6 months after delivery. If the devices are stored for more than one year, solderability may be degraded. Avoid dust, sea breezes and corrosive gases (Cl2, NH3, SO2, NOX, etc.). CAUTION ELECTROSTATIC SENSITIVE DEVICES DO NOT OPEN PACKAGES OR HANDLE EXCEPT AT A STATIC-FREE WORKSTATION DOCUMENT IDENTIFICATION REVISION NOTES: DATA SHEET The product is in production. Gennum reserves the right to make changes at any time to improve reliability, function or design, in order to provide the best product possible. Changed to E3 Package. Added ‘Pb-free’ bullet to front page. Added Pb-free solder reflow profile. GENNUM CORPORATION MAILING ADDRESS: P.O. Box 489, Stn. A, Burlington, Ontario, Canada L7R 3Y3 Tel. +1 (905) 632-2996 Fax. +1 (905) 632-5946 SHIPPING ADDRESS: 970 Fraser Drive, Burlington, Ontario, Canada L7L 5P5 For latest product information, visit www.gennum.com. GENNUM JAPAN CORPORATION Shinjuku Green Tower Building 27F 6-14-1, Nishi Shinjuku Shinjuku-ku, Tokyo 160-0023 Japan Tel: +81 (03) 3349-5501 Fax: +81 (03) 3349-5505 GENNUM UK LIMITED 25 Long Garden Walk, Farnham, Surrey, England GU9 7HX Tel. +44 (0)1252 747 000 Fax +44 (0)1252 726 523 Gennum Corporation assumes no responsibility for the use of any circuits described herein and makes no representations that they are free from patent infringement. © Copyright June 1999 Gennum Corporation. All rights reserved. Printed in Canada. 5 of 5 522 - 40 - 04