LCD Switches Programmable High Resolution LCD Switches IS Series DISTINCTIVE CHARACTERISTICS • • • • • • • • • • • • High resolution of 64 x 32 pixels 64 colors of backlighting can be controlled dynamically Pushbutton switch or display with LCD, RGB LED backlighting General brightness of backlight is dynamically controlled in eight steps from dark to bright Operated by commands and data supplied via SPI communications protocol Can display as many as four lines of text with ten characters each Incorporates bitmap display function Programmable display graphics for alphanumeric characters and animated sequences Dual image VRAM for quick change of displayed images Distinct, long travel of 4.5mm (same as KP01 Series) Low energy consumption Dust tight construction Viewing area: 15.5mm x 11.6mm (horizontal x vertical) High reliability and long life of three million actuations minimum Epoxy Sealed Straight PC Terminals Snap-in Standoff for Easy, Secure Mounting and Alignment Viewing area: 12.9mm x 9.9mm (horizontal x vertical) High resolution of 52RGB x 36 pixels Crimped terminals ensure secure PC mounting and prevent dislodging during wave soldering APPLICATIONS Actual Sizes The High Resolution SMARTSWITCH multiple applications, including: TM Series complements • Broadcast equipment • Image equipment • Education equipment • Vending machines • Audio equipment • POS • Automation control equipment [email protected] www.greatecs.com 1 LCD Switches Programmable High Resolution LCD Switches IS Series SMARTSWITCH PART NUMBER & DESCRIPTION Part Number Switch Description SPST Momentary ON Gold Contacts Straight PC Terminals IS15DBFP4RGB LCD Mode LED Color LCD/LED Black & White FSTN Positive Red/Green/Blue SMARTSWITCH SPECFICATIONS Circuit SPST normally open Electrical Capacity (Resistive Load) 100mA @ 12V DC Contact Resistance 200 milliohms maximum @ 20mV 10mA Insulation Resistance 100 megohms minimum @ 100V DC Dielectric Strength 125V AC for 1 minute minimum Mechanical Endurance 3,000,000 operations minimum Electrical Endurance 3,000,000 operations minimum Operating Force 2.0 ± 0.5 Newtons Total Travel 4.5mm (.177”) SMARTSWITCH OLED SPECFICATIONS Characteristics of Display Display Operation Mode FSTN positive; background colors, black & white Display Condition Viewing Angle Direction 6 o’clock Viewing Area 15.0mm x 10.8mm (horizontal x vertical) Pixel Format 64 x 32 pixels (horizontal x vertical) Pixel Size 0.20mm x 0.27mm (horizontal x vertical) * Operating Temperature Range –15°C ~ +50°C (+32°F ~ +122°F) Storage Temperature Range –20°C ~ +60°C (–4°F ~ +140°F) Backlight LED RGB: red/green/blue * In low temperature environment (below 0°C), speed and contrast decrease when image changes. The non-indicator dot may become dense in a high temperature environment (about 50°C). Absolute Maximum Ratings Items Recommended Operating Conditions Symbols Ratings Items Symbols Minimum Typical Maximum 4.9V 5.0V 5.1V Supply Voltage V DD –0.3V to +7.0V Supply Voltage V DD Input Voltage VI –0.3V to V DD +0.3V Input Voltage VI 0V –– V DD Output Voltage VO –0.3V to V DD +0.3V SPI Clock Frequency fS CK –– –– 8MHz Current Consumption I DD ** 10mA –– *** 50mA Optical Characteristics (Temperature at 25°C) Items Symbols Min Typical Max Cr –– 3.0 –– Up & Down θ –– 90° –– Right & Left Φ –– 90° –– Contrast Ratio Viewing Angle (Cr ≥ 1.1) [email protected] ** 10mA: Backlighting LED is off *** 50mA: Backlighting LEDs (Red, Green, Blue) are maximum brightness www.greatecs.com 2 LCD Switches Programmable High Resolution LCD Switches IS Series SMARTSWITCH BLOCK DIAGRAM & PIN CONFIGURATIONS Com1......Com32 Common Driver 32bit Shift Register 64 x 32 Dot Matrix LCD Panel seg1.......seg64 Segment Driver Backlight LED 64bit Shift Register Display Controller NC 9 SS 8 SCK 7 SDI 6 RAM #1 256Byte Red Green Blue RAM #2 256Byte LED Driver SPI IS15DBFP4RGB with RGB LED and Black and White LCD Mode SDO 5 4 VDD GND 3 SW 2 SW 1 Pin No. Symbol 1 2 3 4 5 6 Name SW SW GND V DD SDO SDI SCK SS NC 7 8 9 Function Terminal of Switch Terminal of Switch Ground Power Data Out Data In Serial Clock Slave Select None Normally open Normally open Power source for logic circuit and LCD Data output line for SPI Data input line for SPI Clock line for SPI that synchronizes commands and data Chip select for SPI; line is active low No connection SMARTSWITCH TYPICAL DIMENSIONS See Pixel Detail Terminal numbers are not on the switch. (15.0) .591 (14.38) .566 (3.9) .154 (18.0) .709 Standoff 1 Standoff 2 (0.6) Typ .024 (20.59) .811 (13.5) .531 (9.42) .371 (10.8) .425 (16.0) .630 (0.20) .008 (0.02) Typ .0008 Pixel Detail (0.4) Typ .016 See Standoff Detail (23.0) .906 (23.13) .911 (0.27) .010 Standoff Detail (0.2) .008 (16.0) .630 A 1 Dimension A Standoff 2 = (2.3) Standoff 1 = (2.7) .091 .106 (7.05) .278 (8.0) .315 (2.0) .079 (18.0) .709 (1.0)Typ .039 (6.0) .236 9 3 2x (0.8) (1.0) Dia .031 ~ .03 9 2 8 4 1 7x (0.8) ~ (1.0) Dia .031 .039 (2.0) .079 (6.0) .236 Standoff 1 (0.3) Typ .012 Footprint (1.25) .049 9 8 7 6 5 4 3 (7.62) .300 Standoff 2 (3.4) .134 (2.0) Dia .079 [email protected] (1.0)Typ .039 2 (7.05) .278 (8.0) .315 (7.62) .300 (16.0) .630 4x (1.3) Dia .051 www.greatecs.com 3 LCD Switches Programmable High Resolution LCD Switches IS Series SMARTSWITCH PART NUMBER & DESCRIPTION Part Number Terminals LCD Mode LED Color IS01DBFRGB Straight PC Black & White FSTN Positive Red/Green/Blue LCD/LED SMARTSWITCH LCD SPECFICATIONS Characteristics of Display Display Operation Mode FSTN positive; background colors, black & white Display Condition Viewing Angle Direction 6 o’clock Viewing Area 13.9mm x 10.6mm (horizontal x vertical) Pixel Format 64 x 32 pixels (horizontal x vertical) Pixel Size 0.18mm x 0.24mm (horizontal x vertical) * Operating Temperature Range –15°C ~ +50°C (+5°F ~ +122°F) Storage Temperature Range –20°C ~ +60°C (–4°F ~ +140°F) Backlight LED RGB: red/green/blue * In low temperature environment (below 0°C), speed and contrast decrease when image changes. The non-indicator dot may become dense in a high temperature environment (about 50°C). Absolute Maximum Ratings Items Recommended Operating Conditions Symbols Ratings Items Symbols Minimum Typical Maximum 4.9V 5.0V 5.1V Supply Voltage V DD –0.3V to +7.0V Supply Voltage V DD Input Voltage VI –0.3V to V DD +0.3V Input Voltage VI 0V –– V DD Output Voltage VO –0.3V to V DD +0.3V SPI Clock Frequency fS CK –– –– 8MHz Current Consumption I DD ** 10mA –– *** 50mA Optical Characteristics (Temperature at 25°C) Items Symbols Min Typical Max Cr –– 3.0 –– Up & Down θ –– 90° –– Right & Left Φ –– 90° –– Contrast Ratio Viewing Angle (Cr ≥ 1.1) [email protected] ** 10mA: Backlighting LED is off *** 50mA: Backlighting LEDs (Red, Green, Blue) are maximum brightness www.greatecs.com 4 LCD Switches Programmable High Resolution LCD Switches IS Series SMARTSWITCH BLOCK DIAGRAM & PIN CONFIGURATIONS Com1......Com32 Common Driver 32bit Shift Register 64 x 32 Dot Matrix LCD Panel seg1.......seg64 Segment Driver Backlight LED 64bit Shift Register Display Controller RAM #1 256Byte SCK 1 SS 2 SDI Green Blue RAM #2 256Byte LED Driver SPI SDO 3 Red IS01DBFRGB with RGB LED and Black and White LCD Mode 4 GND 5 VDD 6 Pin No. Symbol Name Function 1 SCK Serial Clock Clock line for SPI that synchronizes commands and data 2 SS Slave Select Chip select for SPI; line is active low 3 SDO Data Out Data output line for SPI 4 SDI Data In Data input line for SPI 5 GND Ground 6 V DD Power Power source for logic circuit and LCD SMARTSWITCH TYPICAL DIMENSIONS Terminal numbers are not on the device. See Pixel Detail (13.9) .547 (12.78) .503 (10.7) .421 (17.2) .677 (10.0) .394 (1.3) .051 (0.5) Sq Typ .020 (16.8) .661 (4.0) .157 (8.3) .327 (10.6) .417 (0.65) Typ .026 Key (3.1) .122 (0.4) Typ .016 2 1 6 5 (14.7) .579 (2.0) Typ .079 (14.4) .567 (17.8) .701 (0.7) .028 (9.9) .390 (2.0) .079 (15.0) .591 (3.0) .118 CL (0.18) .007 (0.02) Typ .0008 (0.24) .009 Pixel Detail Footprint (16.8) .661 (2.0) Typ .079 4x (0.9) Dia .035 [email protected] (3.1) .122 1 2 5 6 (10.0) .394 (15.0) .591 (2.0) .079 (4.0) .157 (14.7) .579 3x (0.9) Dia .035 6x (0.8) Dia .031 www.greatecs.com 5 LCD Switches Programmable High Resolution LCD Switches IS Series TIMING SPECIFICATIONS FOR SMARTSWITCH & SMARTDISPLAY Circuit Example SPI Characteristics (See Timing Diagram) (Temperature at –15°C ~ +50°C and V Items Symbols Minimum t sS S SPI_SS Set Up Time CLK_1 DD = 5.0V ± 2%) Maximum SCK SDI SS SCK SDI SS SCK SDI SS IS_1 IS_2 IS_3 SCK SDI SS SCK SDI SS SCK SDI SS IS_4 IS_5 IS_6 SCK SDI SS SCK SDI SS SCK SDI SS 10ns SPI_SS Hold Time t hS S SPI_CLK Cycle t c ycC K SPI_CLK Width t hwC K 10ns SPI_DI Set Up Time t sD I 10ns SPI_DI Hold Time t hD I 10ns SPI_DO Delay Time t dD O 10ns CLK_2 10ns 8MHz CLK_3 IS_7 DATA_1 SPI Timing Chart (SS Using) SS Low t c y cCK th wCK SCK thDI SDI SCK t s DI ts DI SDI IS_9 DATA_3 SPI Timing Chart (SS Low Level Fixed) SS t hSS t sSS t c y cCK IS_8 DATA_2 t h wCK t hDI D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 t dDO SDO tdDO SDO D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 SDI and SCK shall be kept high when the communication is not complete. BITMAP Segment 1 2 3 4 5 6 7 8 Byte8 COM1 D0 D1 D2 D3 D4 D5 D6 D7 9 • • • 16 ••••• 49 • • • 56 Byte7 ••• Byte2 D0 • • • D7 ••• D0 • • • D7 Byte16 COM2 57 58 59 60 61 62 63 64 Byte1 D0 D1 D2 D3 D4 D5 D6 D7 Byte9 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 • • • • • • • • • Byte256 COM32 ••• ••• D0 D1 D2 D3 D4 D5 D6 D7 Byte249 D0 D1 D2 D3 D4 D5 D6 D7 Transferring Display Data/Displaying LCD Command and Data Sequence Command 0 x 55 0 1 0 1 0 1 0 1 Notes: Data (256 Bytes) Byte1 D7 D6 D5 D4 D3 D2 D1 D0 Byte2 • • • Byte255 D7 D6 • • • D1 D0 Byte256 D7 D6 D5 D4 D3 D2 D1 D0 The screens are changed when the second area is fully stored. [email protected] www.greatecs.com 6 LCD Switches Programmable High Resolution LCD Switches IS Series COMMANDS & DATA FOR SMARTSWITCH & SMARTDISPLAY • • • • • • • • Transferring display data/displaying on LCD: command (1 Byte) + data (256 Bytes) Others: command (1 Byte) + data (1 Byte) Commands can be accepted only when all bits coincide; otherwise, they are not acknowledged Additional commands will not be received until the communicatio n of commands (1 Byte) and data (256 or 1 Byte) is completed There is no time limit from the beginning to end of data receipt Commands may be executed consecutively (no need to wait between commands) Irregular commands or data is not recognized Initial status at power activation: LCD display off, LED off (brightness 1/20, color off) Transferring Display Data/Displaying on LCD Command Hex Binary 0 x 55 01010101 Data 256 Bytes (64 x 32 = 2,048 bits) Remarks See below for details of bitmap data LED (Backlight) Color Set Command Hex 0 x 40 Data Binary 01000000 R R G G B B 1 1 2 bits x 3 Remarks For each of RGB: 00 = off 01 = 1/4 10 = 1/2 11 = full LED (Backlight) Brightness Set Command Hex 0 x 41 Data Binary 01000001 *** 1 1 1 1 1 3 bits Remarks For leading 3bits: 100 = 1/3 000 = 1/20 (dark) 101 = 1/2 110 = 2/3 001 = 1/10 111 = full 010 = 1/7 011 = 1/5 (bright) Reset (Returning to Initial Status at Power Activation) Command Hex Binary 0 x 5E 01011110 Data 00000011 Remarks Returning to initial status at power activation PRECAUTIONS FOR HANDLING & STORAGE ATTENTION Handling ELECTROST AT IC SENSITIVE DEVICES 1. The IS Series devices are electrostatic sensitive. 2. Limit operating force to keytop to 100.0N maximum, as excessive pressure may damage the LCD device. 3. The IS series devices are not process sealed. 4. If the LCD is accidentally broken, avoid contact with the liquid and wash off any liquid spills to the skin or clothing. 5. Clean cap surface with dry cloth. If further cleaning is needed, wipe with dampened cloth using neutral cleanser and dry with clean cloth. Do not use organic solvent. 6. Recommended soldering time and temperature limits: 5 second s maximum @ 270°C maximum 7. Do not exceed 60°C at the LCD level. Storage 1. Store in original container and away from direct sunlight. 2. Keep away from static electricity. 3. Avoid extreme temperatures, high humidity, gaseous substances, and all forms of chemical contamination. [email protected] www.greatecs.com 7