KINGBRIGHT AA2214QBS-D-AMT

2.2x1.4mm SURFACE MOUNT LED LAMP
Part Number: AA2214QBS/D-AMT
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
DISCHARGE
SENSITIVE
DEVICES
Blue
Description
The Blue source color devices are made with InGaN Light
Emitting Diode.
Features
Static electricity and surge damage the LEDS.
z High reliability LED package.
z 2.2mm x 1.4mm, 1.3mm high.
z Low power consumption.
It is recommended to use a wrist band or anti-electrostatic
glove when handling the LEDs.
All devices, equipment and machinery must be electrically
z Available on tape and reel.
grounded.
z Package : 2000pcs / reel.
z Moisture sensitivity level : level 3.
z RoHS compliant.
Applications
z Traffic signaling.
z Backlighting (illuminated advertising , general lighting).
z Interior and exterior automotive lighting.
z Substitution of micro incandescent lamps.
z Reading lamps.
Package Dimensions
z Signal and symbol luminaire for orientation.
z Marker lights (e.g. Steps, exit ways, etc).
z Decorative and entertainment lighting.
z Indoor and outdoor commercial and residential
architectural lighting.
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.2(0.008") unless otherwise noted.
3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAL4009
REV NO: V.1
DATE: NOV/22/2010
PAGE: 1 OF 7
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: C.H.HAN
ERP: 1201007405
Handling Precautions
Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic
significantly reduces thermal stress, it is more susceptible to damage by external mechanical force.
As a result, special handling precautions need to be observed during assembly using silicone encapsulated
LED products. Failure to comply might lead to damage and premature failure of the LED.
1. Handle the component along the side surfaces by using forceps or appropriate tools.
2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry.
3. Do not stack together assembled PCBs containing exposed LEDs. Impact may scratch the silicone lens or
damage the internal circuitry.
4. The outer diameter of the SMD pickup nozzle should not exceed the size of the LED to prevent air leaks. The inner diameter
of the nozzle should be as large as possible.
5. A pliable material is suggested for the nozzle tip to avoid scratching or damaging the LED surface during pickup.
6. The dimensions of the component must be accurately programmed in the pick-and-place machine to insure precise pickup
and avoid damage during production.
SPEC NO: DSAL4009
REV NO: V.1
DATE: NOV/22/2010
PAGE: 2 OF 7
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: C.H.HAN
ERP: 1201007405
Selection Guide
Part No.
Dice
AA2214QBS/D-AMT
Iv (mcd) [2]
@ 20mA
Lens Type
Blue (InGaN)
Viewing
Angle [1]
Code.
Min.
Max.
M
80
120
N
120
200
P
200
300
Water Clear
2θ1/2
120°
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity/ luminous Flux: +/-15%.
Absolute Maximum Ratings at Ta=25°C
Parameter
Symbol
Value
Unit
Power dissipation
PD
120
mW
Junction temperature
TJ
110
°C
Reverse Voltage
VR
5
V
Operating Temperature
Top
-40 To +100
°C
Storage Temperature
Tstg
-40 To +110
°C
IF
30
mA
IFM
150
mA
250
V
250
°C/W
DC Forward Current[1]
Peak Forward Current [2]
Electrostatic Discharge Threshold (HBM)
Thermal Resistance (Junction/ambient) [1]
Rth j-a
Notes:
1. Rth(j-a) Results from mounting on PC board FR4 (pad size≥16 mm 2 per pad),
2. 1/10 Duty Cycle, 0.1ms Pulse Width.
Electrical / Optical Characteristics at Ta=25°C
Parameter
Symbol
Wavelength at peak emission
Dominant Wavelength
IF=20mA
IF=20mA
Reverse Current (VR = 5V)
Spectral bandwidth at 50%Φ
Forward Voltage
REL MAX
Value
Code.
Min.
λ peak
λ dom [1]
Typ.
468
461
468
2A
464
471
2B
467
473
3A
469
475
3B
471
477
IF=20mA
50
Δλ
VF [2]
25
-
3.3
Unit
nm
1B
IR
IF=20mA
Max.
nm
uA
nm
4.0
V
Temperature coefficient of λ peak
IF=20mA, -10 ° C≤ T≤100 ° C
TC λ peak
0.05
nm/ ° C
Temperature coefficient of λ dom
IF=20mA, -10 ° C≤ T≤100 ° C
TC λ dom
0.03
nm/ ° C
Temperature coefficient of VF
IF=20mA, -10 ° C≤ T≤100 ° C
TCV
-2.5
mV/ ° C
Notes:
1.The dominant Wavelength (λ d) above is the setup value of the sorting machine. (Tolerance λ d : ±1nm. )
2. Forward Voltage: +/-0.1V.
SPEC NO: DSAL4009
REV NO: V.1
DATE: NOV/22/2010
PAGE: 3 OF 7
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: C.H.HAN
ERP: 1201007405
Blue
AA2214QBS/D-AMT
SPEC NO: DSAL4009
REV NO: V.1
DATE: NOV/22/2010
PAGE: 4 OF 7
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: C.H.HAN
ERP: 1201007405
AA2214QBS/D-AMT
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Reel Dimension
Tape Dimensions
(Units : mm)
SPEC NO: DSAL4009
REV NO: V.1
DATE: NOV/22/2010
PAGE: 5 OF 7
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: C.H.HAN
ERP: 1201007405
PACKING & LABEL SPECIFICATIONS
AA2214QBS/D-AMT
SPEC NO: DSAL4009
REV NO: V.1
DATE: NOV/22/2010
PAGE: 6 OF 7
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: C.H.HAN
ERP: 1201007405
Reliability Test Items And Conditions
The reliability of products shall be satisfied with items listed below
Lot Tolerance Percent Defective (LTPD) : 10%
No. Test Item
Standards
Test Times / Number of
Cycles
Damaged
Test Condition
1
Continuous operating test
-
Ta =25°C ,IF = maximum rated current*
1,000 h
0 / 22
2
High Temp. operating test
EIAJED4701/100(101)
Ta = 100°C IF = maximum rated current*
1,000 h
0 / 22
3
Low Temp. operating test
-
Ta = -40°C, IF = maximum rated current*
1,000 h
0 / 22
4
High temp. storage test
EIAJEDTa = maximum rated storage temperature
4701/100(201)
1,000 h
0 / 22
5
Low temp. storage test
EIAJED4701/100(202)
Ta = -40°C
1,000 h
0 / 22
6
High temp. & humidity storage test
EIAJED4701/100(103)
Ta = 60°C, RH = 90%
1,000 h
0 / 22
7
High temp. & humidity operating test
EIAJED4701/100(102)
Ta = 60°C, RH = 90%
IF = maximum rated current*
1,000 h
0 / 22
8
Soldering reliability test
EIAJED4701/100(301)
Moisture soak : 30°C,70% RH, 72h
Preheat : 150~180°C(120s max.)
Soldering temp : 260°C(10s)
3 times
0 / 18
9
Thermal shock operating test
-
Ta = -40°C(15min) ~ 100°C(15min)
IF = derated current at 100°C
1,000 cycles
0 / 22
10
Thermal shock test
-
Ta = -40°C(15min) ~ maximum rated
storage temperature(15min)
1,000 cycles
0 / 22
11
Electric Static Discharge (ESD)
EIAJED4701/100(304)
C = 100pF , R2 = 1.5KΩ V = 250V
Once each
Polarity
0 / 22
12
Vibration test
-
a = 196m/s² , f = 100~2KHz ,
t = 48min for all xyz axes
4 times
0 / 22
* : Refer to forward current vs. derating curve diagram
Failure Criteria
Items
Symbols Conditions
Failure Criteria
luminous Intensity
lv
IF = 20mA
Testing Min. Value <Spec.Min.Value x 0.5
Forward Voltage
VF
IF = 20mA
Testing Max. Value ≥Spec.Max.Value x 1.2
Reverse Current
IR
VR = Maximum Rated Reverse Voltage
Testing Max. Value ≥Spec.Max.Value x 2.5
High temp. storage test
-
-
Occurrence of notable decoloration, deformation
and cracking
SPEC NO: DSAL4009
REV NO: V.1
DATE: NOV/22/2010
PAGE: 7 OF 7
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: C.H.HAN
ERP: 1201007405