2.2x1.4mm SURFACE MOUNT LED LAMP Part Number: AA2214ZGS-AMT Green ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Description The Green source color devices are made with InGaN on Sapphire Light Emitting Diode. Features Static electricity and surge damage the LEDS. z High reliability LED package. z 2.2mm x 1.4mm, 1.3mm high. z Low power consumption. It is recommended to use a wrist band or anti-electrostatic glove when handling the LEDs. All devices, equipment and machinery must be electrically z Available on tape and reel. grounded. z Package : 2000pcs / reel. z Moisture sensitivity level : level 3. Applications z RoHS compliant. z Traffic signaling. z Backlighting (illuminated advertising , general lighting). z Interior and exterior automotive lighting. z Substitution of micro incandescent lamps. z Reading lamps. Package Dimensions z Signal and symbol luminaire for orientation. z Marker lights (e.g. Steps, exit ways, etc). z Decorative and entertainment lighting. z Indoor and outdoor commercial and residential architectural lighting. Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.2(0.008") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAL4010 REV NO: V.1 DATE: NOV/22/2010 PAGE: 1 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.HAN ERP: 1201007406 Handling Precautions Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more susceptible to damage by external mechanical force. As a result, special handling precautions need to be observed during assembly using silicone encapsulated LED products. Failure to comply might lead to damage and premature failure of the LED. 1. Handle the component along the side surfaces by using forceps or appropriate tools. 2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry. 3. Do not stack together assembled PCBs containing exposed LEDs. Impact may scratch the silicone lens or damage the internal circuitry. 4. The outer diameter of the SMD pickup nozzle should not exceed the size of the LED to prevent air leaks. The inner diameter of the nozzle should be as large as possible. 5. A pliable material is suggested for the nozzle tip to avoid scratching or damaging the LED surface during pickup. 6. The dimensions of the component must be accurately programmed in the pick-and-place machine to insure precise pickup and avoid damage during production. SPEC NO: DSAL4010 REV NO: V.1 DATE: NOV/22/2010 PAGE: 2 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.HAN ERP: 1201007406 Selection Guide Part No. Dice AA2214ZGS-AMT Iv (mcd) [2] @ 20mA Lens Type Green (InGaN) Viewing Angle [1] Code. Min. Max. R 400 500 S 500 700 T 700 1000 Water Clear 2θ1/2 120° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. Absolute Maximum Ratings at Ta=25°C Symbol Value Unit Power dissipation Parameter PD 123 mW Reverse Voltage VR 5 V Junction temperature TJ 110 °C Operating Temperature Top -40 To +100 °C Storage Temperature Tstg -40 To +110 °C IF 30 mA IFM 150 mA 450 V 250 °C/W DC Forward Current[1] Peak Forward Current [2] Electrostatic Discharge Threshold (HBM) Thermal Resistance (Junction/ambient) [1] Rth j-a Notes: 1. Rth(j-a) Results from mounting on PC board FR4 (pad size≥16 mm 2 per pad), 2. 1/10 Duty Cycle, 0.1ms Pulse Width. Electrical / Optical Characteristics at Ta=25°C Parameter Symbol Wavelength at peak emission Dominant Wavelength Spectral bandwidth at 50%Φ Forward Voltage IF=20mA IF=20mA REL MAX IF=20mA IF=20mA Value Code. Min. λ peak λ dom [1] Typ. Max. 515 nm 1 513 522 2 518 527 3 523 532 4 528 537 Δλ VF [2] 30 2.7 3.3 Unit nm nm 4.1 V 50 uA Reverse Current (VR = 5V) IR Temperature coefficient of λ peak IF=20mA, -10 ° C≤ T≤100 ° C TC λ peak 0.09 nm/ ° C Temperature coefficient of λ dom IF=20mA, -10 ° C≤ T≤100 ° C TC λ dom 0.05 nm/ ° C Temperature coefficient of VF IF=20mA, -10 ° C≤ T≤100 ° C TCV -2.5 mV/ ° C Notes: 1.The dominant Wavelength (λ d) above is the setup value of the sorting machine. (Tolerance λ d : ±1nm. ) 2. Forward Voltage: +/-0.1V. SPEC NO: DSAL4010 REV NO: V.1 DATE: NOV/22/2010 PAGE: 3 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.HAN ERP: 1201007406 Green AA2214ZGS-AMT SPEC NO: DSAL4010 REV NO: V.1 DATE: NOV/22/2010 PAGE: 4 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.HAN ERP: 1201007406 AA2214ZGS-AMT Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAL4010 REV NO: V.1 DATE: NOV/22/2010 PAGE: 5 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.HAN ERP: 1201007406 PACKING & LABEL SPECIFICATIONS AA2214ZGS-AMT SPEC NO: DSAL4010 REV NO: V.1 DATE: NOV/22/2010 PAGE: 6 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.HAN ERP: 1201007406 Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below Lot Tolerance Percent Defective (LTPD) : 10% No. Test Item Standards Test Times / Number of Cycles Damaged Test Condition 1 Continuous operating test - Ta =25°C ,IF = maximum rated current* 1,000 h 0 / 22 2 High Temp. operating test EIAJED4701/100(101) Ta = 100°C IF = maximum rated current* 1,000 h 0 / 22 3 Low Temp. operating test - Ta = -40°C, IF = maximum rated current* 1,000 h 0 / 22 4 High temp. storage test EIAJEDTa = maximum rated storage temperature 4701/100(201) 1,000 h 0 / 22 5 Low temp. storage test EIAJED4701/100(202) Ta = -40°C 1,000 h 0 / 22 6 High temp. & humidity storage test EIAJED4701/100(103) Ta = 60°C, RH = 90% 1,000 h 0 / 22 7 High temp. & humidity operating test EIAJED4701/100(102) Ta = 60°C, RH = 90% IF = maximum rated current* 1,000 h 0 / 22 8 Soldering reliability test EIAJED4701/100(301) Moisture soak : 30°C,70% RH, 72h Preheat : 150~180°C(120s max.) Soldering temp : 260°C(10s) 3 times 0 / 18 9 Thermal shock operating test - Ta = -40°C(15min) ~ 100°C(15min) IF = derated current at 100°C 1,000 cycles 0 / 22 10 Thermal shock test - Ta = -40°C(15min) ~ maximum rated storage temperature(15min) 1,000 cycles 0 / 22 11 Electric Static Discharge (ESD) EIAJED4701/100(304) C = 100pF , R2 = 1.5KΩ V = 450V Once each Polarity 0 / 22 12 Vibration test - a = 196m/s² , f = 100~2KHz , t = 48min for all xyz axes 4 times 0 / 22 * : Refer to forward current vs. derating curve diagram Failure Criteria Items Symbols Conditions Failure Criteria luminous Intensity lv IF = 20mA Testing Min. Value <Spec.Min.Value x 0.5 Forward Voltage VF IF = 20mA Testing Max. Value ≥Spec.Max.Value x 1.2 Reverse Current IR VR = Maximum Rated Reverse Voltage Testing Max. Value ≥Spec.Max.Value x 2.5 High temp. storage test - - Occurrence of notable decoloration, deformation and cracking SPEC NO: DSAL4010 REV NO: V.1 DATE: NOV/22/2010 PAGE: 7 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.HAN ERP: 1201007406