TPS3103xxx TPS3106xxx TPS3110xxx www.ti.com SLVS363E – AUGUST 2001 – REVISED SEPTEMBER 2007 UltraLow Supply-Current/Supply-Voltage Supervisory Circuits FEATURES 1 • Precision Supply Voltage Supervision Range: 0.9 V, 1.2 V, 1.5 V, 1.6 V, 2 V, and 3.3 V • High Trip-Point Accuracy: 0.75% • Supply Current of 1.2 μA (typical) • RESET Defined With Input Voltages as Low as 0.4 V • Power-On Reset Generator With a Delay Time of 130 ms • Push/Pull or Open-Drain RESET Outputs • SOT23-6 Package • Package Temperature Range: –40°C to +85°C 2 APPLICATIONS • • • • • • DESCRIPTION The TPS310x and TPS311x families of supervisory circuits provide circuit initialization and timing supervision, primarily for DSP and processor-based systems. During power-on, RESET is asserted when the supply voltage (VDD) becomes higher than 0.4 V. Thereafter, the supervisory circuit monitors VDD and keeps the RESET output active as long as VDD remains below the threshold voltage (VIT). An internal timer delays the return of the output to the inactive state to ensure proper system reset. The delay time starts after VDD has risen above VIT. When VDD drops below VIT, the output becomes active again. All the devices of this family have a fixed-sense threshold voltage (VIT) set by an internal voltage divider. Applications Using Low-Power DSPs, Microcontrollers, or Microprocessors Portable- and Battery-Powered Equipment Intelligent Instruments Wireless Communication Systems Industrial Equipment Notebook/Desktop Computers The TPS3103 and TPS3106 have an active-low, open-drain RESET output. The TPS3110 has an active-low push/pull RESET. The product spectrum is designed for supply voltages of 0.9 V up to 3.3 V. The circuits are available in SOT23-6 packages. The TPS31xx family is characterized for operation over a temperature range of –40°C to +85°C. TPS3106 DBV PACKAGE (TOP VIEW) TPS3103 DBV PACKAGE (TOP VIEW) 3.3 V RESET 1 6 VDD RSTVDD 1 6 VDD GND 2 5 PFO GND 2 5 RSTSENSE 4 PFI 1.6 V VCORE VDD MR 3 TPS3106K33DBV R3 VIO DSP R1 MR 3 4 SENSE MR RSTVDD RESET SENSE TPS3110 DBV PACKAGE (TOP VIEW) R2 RSTSENSE GND RESET 1 6 VDD GND 2 5 WDI MR 3 4 SENSE GND GND Typical Application Circuit 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2001–2007, Texas Instruments Incorporated TPS3103xxx TPS3106xxx TPS3110xxx www.ti.com SLVS363E – AUGUST 2001 – REVISED SEPTEMBER 2007 This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. ORDERING INFORMATION (1) (1) (2) PRODUCT NOMINAL SUPPLY VOLTAGE THRESHOLD VOLTAGE, VIT (2) TPS3103E12DBVR 1.2 V 1.142 V TPS3103E15DBVR 1.5 V 1.434 V TPS3103H20DBVR 2.0 V 1.84 V TPS3103K33DBVR 3.3 V 2.941 V TPS3106E09DBVR 0.9 V 0.86 V TPS3106E16DBVR 1.6 V 1.521 V TPS3106K33DBVR 3.3 V 2.941 V TPS3110E09DBVR 0.9 V 0.86 V TPS3110E12DBVR 1.2 V 1.142 V TPS3110E15DBVR 1.5 V 1.434 V TPS3110K33DBVR 3.3 V 2.941 V For the most current package and ordering information see the Package Option Addendum at the end of this document, or see the TI web site at www.ti.com. Custom threshold voltages are available. Minimum order quantities apply. Contact factory for details and availability. AVAILABLE OPTIONS DEVICE RESET OUTPUT TPS3103 Open-drain RSTSENSE, RSTVDD OUTPUT TPS3106 TPS3110 SENSE INPUT WDI INPUT PFO OUTPUT Open-drain Open-drain Push-pull ü ü ü ABSOLUTE MAXIMUM RATINGS (1) Over operating free-air temperature range, unless otherwise noted. Supply voltage, VDD (2) MR Pin, VMR All other pins (2) VALUE UNIT –0.3 to +3.6 V –0.3 to VDD + 0.3 V –0.3 to +3.6 V Maximum low output current, IOL 5 mA Maximum high output current, IOH –5 mA Input clamp current, IIK (VI < 0 or VI > VDD) ±10 mA Output clamp current, IOK (VO < 0 or VO > VDD) (3) ±10 mA Continuous total power dissipation See Dissipation Rating Table Operating temperature range, TA –40 to +85 °C Storage temperature range, TSTG –65 to +150 °C +260 °C Soldering temperature (1) (2) (3) 2 Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltage values are with respect to GND. For reliable operation, the device must not be operated at 3.6 V for more than t = 1000h continuously. Output is clamped for push-pull outputs by the back gate diodes internal to the IC. No clamp exists for the open-drain outputs. Submit Documentation Feedback Copyright © 2001–2007, Texas Instruments Incorporated TPS3103xxx TPS3106xxx TPS3110xxx www.ti.com SLVS363E – AUGUST 2001 – REVISED SEPTEMBER 2007 DISSIPATION RATINGS PACKAGE TA ≤ +25°C POWER RATING DERATING FACTOR ABOVE TA = +25°C TA = +70°C POWER RATING TA = +85°C POWER RATING DBV 437 mW 3.5 mW/°C 280 mW 227 mW RECOMMENDED OPERATING CONDITIONS Over operating free-air temperature range, unless otherwise noted. Supply voltage, VDD (1) Input voltage, VI MIN MAX 0.4 3.3 V 0 VDD + 0.3 V 0.7 × VDD High-level input voltage, VIH at MR, WDI V 0.3 × VDD Low-level input voltage, VIL at MR, WDI Input transition rise and fall rate at Δt/ΔV at MR, WDI Operating temperature range, TA (1) UNIT –40 V 100 ns/V +85 °C For proper operation of SENSE, PFI, and WDI functions: VDD ≥ 0.8 V. ELECTRICAL CHARACTERISTICS Over operating free-air temperature range (unless otherwise noted). PARAMETER TEST CONDITIONS MIN TYP MAX UNIT VDD = 3.3 V, IOH = –3 mA VDD = 1.8 V, IOH = –2 mA VOH High-level output voltage VDD = 1.5 V, IOH = –1 mA 0.8 × VDD V 0.7 × VDD V VDD = 0.9 V, IOH = –0.4 mA VDD = 0.5 V, IOH = –5 μA VDD = 3.3 V, IOL = 3 mA VOL Low-level output voltage VOL Low-level output voltage VDD = 1.5 V, IOL = 2 mA VDD = 1.2 V, IOL = 1 mA 0.3 V 0.1 V VDD = 0.9 V, IOL = 500 μA Negative-going input threshold voltage (1) VIT– VIT – (S) Negative-going input threshold voltage (1) VHYS Hysteresis at VDD input RESET only VDD = 0.4 V, IOL = 5 μA TPS31xxE09 0.854 0.860 0.866 TPS31xxE12 1.133 1.142 1.151 1.423 1.434 1.445 1.512 1.523 1.534 TPS31xxH20 1.829 1.843 1.857 TPS31xxK33 2.919 2.941 2.963 0.542 0.551 0.559 TPS31xxE15 TPS31xxE16 SENSE, PFI TA = +25°C VDD ≥ 0.8 V, TA = +25°C 0.8 V ≤ VIT < 1.5 V 20 1.6 V ≤ VIT < 2.4 V 30 2.5 V ≤ VIT < 3.3 V 50 T(K) Temperature coefficient of VIT−, PFI, SENSE TA = –40°C to +85°C VHYS Hysteresis at SENSE, PFI input VDD ≥ 0.8 V IIH (1) High-level input current –0.012 V V mV –0.019 15 %/K mV MR MR = VDD, VDD = 3.3 V –25 25 SENSE, PFI, WDI SENSE, PFI, WDI = VDD, VDD = 3.3 V –25 25 nA To ensure the best stability of the threshold voltage, a bypass capacitor (ceramic, 0.1 μF) should be placed close to the supply terminals. Copyright © 2001–2007, Texas Instruments Incorporated Submit Documentation Feedback 3 TPS3103xxx TPS3106xxx TPS3110xxx www.ti.com SLVS363E – AUGUST 2001 – REVISED SEPTEMBER 2007 ELECTRICAL CHARACTERISTICS (continued) Over operating free-air temperature range (unless otherwise noted). PARAMETER IIL Low-level input current IOH High-level output current at RESET (2) IDD MIN TYP MAX UNIT MR MR = 0 V, VDD = 3.3 V TEST CONDITIONS –47 –33 –25 μA SENSE, PFI, WDI SENSE, PFI, WDI = 0 V, VDD = 3.3 V –25 25 nA Open-drain VDD = VIT + 0.2 V, VOH = 3.3 V 200 nA Supply current VDD > VIT (average current), VDD < 1.8 V 1.2 3 VDD > VIT (average current), VDD > 1.8 V 2 4.5 VDD < VIT, VDD < 1.8 V 22 VDD < VIT, VDD > 1.8 V 27 Internal pull-up resistor at MR CI (2) μA 70 100 Input capacitance at MR, SENSE, PFI, WDI VI = 0 V to VDD 130 kΩ 1 pF Also refers to RSTVDD and RSTSENSE. SWITCHING CHARACTERISTICS At RL = 1 MΩ, CL = 50 pF, and TA = –40°C to +85°C, unless otherwise noted. PARAMETER TEST CONDITIONS MIN TYP MAX UNIT 65 130 195 ms VIH = 1.1 × VIT, VIL = 0.9 × VIT 40 μs VDD to RESET or RSTVDD delay VIH = 1.1 × VIT, VIL = 0.9 × VIT 40 μs Propagation delay time, high-to-low level output SENSE to RESET or RSTSENSE delay VDD ≥ 0.8 V, VIH = 1.1 × VIT, VIL = 0.9 × VIT 40 μs tPLH Propagation delay time, high-to-low level output SENSE to RESET or RSTSENSE delay VDD ≥ 0.8 V, VIH = 1.1 × VIT, VIL = 0.9 × VIT 40 μs tPHL Propagation delay time, high-to-low level output PFI to PFO delay VDD ≥ 0.8 V, VIH = 1.1 × VIT, VIL = 0.9 × VIT 40 μs tPLH Propagation delay time, low-to-high level output PFI to PFO delay VDD ≥ 0.8 V, VIH = 1.1 × VIT, VIL = 0.9 × VIT 300 μs tPHL Propagation delay time, low-to-high level output MR to RESET. RSTVDD, RSTSENSE delay VDD ≥ 1.1 × VIT, VIL = 0.3 × VDD, VIH = 0.7 × VDD 1 5 μs tPLH Propagation delay time, low-to-high level output MR to RESET. RSTVDD, RSTSENSE delay VDD ≥ 1.1 × VIT, VIL = 0.3 × VDD, VIH = 0.7 × VDD 1 5 μs VDD ≥ 1.1 × VIT, MR = 0.7 × VDD, See Timing Diagrams tD Delay time tPHL Propagation delay time, high-to-low level output VDD to RESET or RSTVDD delay tPLH Propagation delay time, low-to-high level output tPHL TIMING REQUIREMENTS At RL = 1 MΩ, CL = 50 pF, and TA = –40°C to +85°C, unless otherwise noted. PARAMETER tT(OUT) tW 4 Time-out period Pulse width TEST CONDITIONS MIN TYP MAX UNIT 0.55 1.1 1.65 s at WDI VDD ≥ 0.85 V at VDD VIH = 1.1 × VIT, VIL = 0.9 × VIT–, VIT– = 0.86 V 20 at MR VDD ≥ VIT + 0.2 V, VIL = 0.3 × VDD, VIH = 0.7 × VDD 0.1 at SENSE VDD ≥ VIT, VIH = 1.1 × VIT − (S), VIL = 0.9 × VIT − (S) 20 at PFI VDD ≥ 0.85 V, VIH = 1.1 × VIT − (S),VIL = 0.9 × VIT − (S) 20 at WDI VDD ≥ VIT, VIL = 0.3 × VDD, VIH = 0.7 × VDD 0.3 Submit Documentation Feedback μs Copyright © 2001–2007, Texas Instruments Incorporated TPS3103xxx TPS3106xxx TPS3110xxx www.ti.com SLVS363E – AUGUST 2001 – REVISED SEPTEMBER 2007 FUNCTIONAL BLOCK DIAGRAMS TPS3103 VDD VIT+ _ MR Reset Logic and Timer + _ PFI RESET PFO 0.551 V GND TPS3106 VDD VIT- + _ MR + _ SENSE Reset Logic and Timer Reset Logic and Timer RSTVDD RSTSENSE 0.551 V GND Copyright © 2001–2007, Texas Instruments Incorporated Submit Documentation Feedback 5 TPS3103xxx TPS3106xxx TPS3110xxx www.ti.com SLVS363E – AUGUST 2001 – REVISED SEPTEMBER 2007 TPS3110 VDD VIT- + _ MR RESET Reset Logic and Timer + _ SENSE 0.551 V Watchdog Logic and Control WDI GND Table 1. TPS3103 FUNCTION TABLE (1) MR V(PFI) > 0.551 V VDD > VIT RESET PFO L 0 X (1) L L L 1 X L H H 0 0 L L H 0 1 H L H 1 0 L H H 1 1 H H X = Don’t care. Table 2. TPS3106 FUNCTION TABLE MR V(SENSE) > 0.551 V VDD > VIT RSTVDD RSTSENSE (1) X L L H 0 0 L L H 0 1 H L H 1 0 L H H 1 1 H H L (1) X X = Don’t care. Table 3. TPS3110 FUNCTION TABLE (1) MR V(SENSE) > 0.551 V VDD > VIT RESET (2) X L H 0 0 L H 0 1 L H 1 0 L H 1 1 H L (1) (2) 6 X Function of watchdog-timer not shown. X = Don’t care. Submit Documentation Feedback Copyright © 2001–2007, Texas Instruments Incorporated TPS3103xxx TPS3106xxx TPS3110xxx www.ti.com SLVS363E – AUGUST 2001 – REVISED SEPTEMBER 2007 PIN DESCRIPTIONS TPS3106 DBV PACKAGE (TOP VIEW) TPS3103 DBV PACKAGE (TOP VIEW) TPS3110 DBV PACKAGE (TOP VIEW) RESET 1 6 VDD RSTVDD 1 6 VDD GND 2 5 PFO GND 2 5 RSTSENSE MR 3 4 PFI MR 3 4 SENSE RESET 1 6 VDD GND 2 5 WDI MR 3 4 SENSE TERMINAL FUNCTIONS TERMINAL DESCRIPTION NAME DEVICE NO. GND ALL 2 GND MR ALL 3 Manual-reset input. Pull low to force a reset. RESET remains low as long as MR is low and for the timeout period after MR goes high. Leave unconnected or connect to VDD when unused. PFI TPS3103 4 Power-fail input compares to 0.551 V with no additional delay. Connect to VDD if not used. PFO TPS3103 5 Power-fail output. Goes high when voltage at PFI rises above 0.551 V. RESET TPS3103, TPS3110 1 Active-low reset output. Either push-pull or open-drain output stage. RSTSENSE TPS3106 5 Active-low reset output. Logic level at RSTSENSE only depends on the voltage at SENSE and the status of MR. RSTVDD TPS3106 1 Active-low reset output. Logic level at RSTVDD only depends on the voltage at VDD and the status of MR. SENSE TPS3106, TPS3110 4 A reset will be asserted if the voltage at SENSE is lower than 0.551 V. Connect to VDD if unused. VDD ALL 6 Supply voltage. Powers the device and monitors its own voltage. WDI TPS3110 5 Watchdog timer input. If WDI remains high or low longer than the time-out period, then reset is triggered. The timer clears when reset is asserted or when WDI sees a rising edge or a falling edge. Copyright © 2001–2007, Texas Instruments Incorporated Submit Documentation Feedback 7 TPS3103xxx TPS3106xxx TPS3110xxx www.ti.com SLVS363E – AUGUST 2001 – REVISED SEPTEMBER 2007 TIMING DIAGRAMS Timing Diagrams for TPS3103 VDD VIT 0.4 V t tD SENSE VIT - (S) = 0.551 V tD tD tD tD t t RESET Output Condition Undefined Output Condition Undefined t MR t PFI VIT - (S) = 0.551 V t PFO Output Condition Undefined Output Condition Undefined t 8 Submit Documentation Feedback Copyright © 2001–2007, Texas Instruments Incorporated TPS3103xxx TPS3106xxx TPS3110xxx www.ti.com SLVS363E – AUGUST 2001 – REVISED SEPTEMBER 2007 Timing Diagram for TPS3106 VDD VIT 0.4 V tD t tD RSTVDD Output Condition Undefined Output Condition Undefined t SENSE VIT - (S) = 0.551 V RSTSENSE t tD Output Condition Undefined Output Condition Undefined tD t MR t Copyright © 2001–2007, Texas Instruments Incorporated Submit Documentation Feedback 9 TPS3103xxx TPS3106xxx TPS3110xxx www.ti.com SLVS363E – AUGUST 2001 – REVISED SEPTEMBER 2007 Timing Diagram for TPS3110 VDD VIT 0.4 V tD t SENSE VIT - (S) = 0.551 V tD tD tD t tD RESET tD Output Condition Undefined Output Condition Undefined t(TOUT) WDI x = Don’t Care MR t TYPICAL CHARACTERISTICS TPS3110E09 SUPPLY CURRENT vs SUPPLY VOLTAGE TPS3110E09 LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT 20 IDD - Supply Current - mA 18 16 TA = 25°C 14 TA = 0°C SENSE = VDD MR = Open RESET = Open WDI: Triggered 12 10 TA = -40°C 8 6 4 VOL - Low-Level Output Voltage - V 0.30 TA = 85°C VDD = 0.9 V SENSE = GND MR = GND WDI = GND 0.25 0.20 TA = 85°C TA = 25°C 0.15 TA = 0°C 0.10 TA = -40°C 0.05 2 0 0 0.5 1.0 1.5 2.0 2.5 VDD - Supply Voltage - V Figure 1. 10 Submit Documentation Feedback 3.0 0 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 IOL - Low-Level Output Current - mA 2.0 Figure 2. Copyright © 2001–2007, Texas Instruments Incorporated TPS3103xxx TPS3106xxx TPS3110xxx www.ti.com SLVS363E – AUGUST 2001 – REVISED SEPTEMBER 2007 TYPICAL CHARACTERISTICS (continued) TPS3110E09 LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT TPS3110E09 HIGH-LEVEL OUTPUT VOLTAGE vs HIGH-LEVEL OUTPUT CURRENT 0.90 1.0 VDD = 3.3 V SENSE = GND MR = GND WDI = GND 0.8 TA = 85°C VOH - High-Level Output Voltage - V VOL - Low-Level Output Voltage - V 0.9 TA = 25°C 0.7 0.6 TA = 0°C 0.5 TA = -40°C 0.4 0.3 0.2 0.85 TA = 85°C 0.80 0.75 TA = 25°C TA = 0°C 0.70 VDD = 0.9 V SENSE = VDD MR = VDD WDI : Triggered 0.65 0.1 0 0 2 4 6 8 10 12 14 16 18 0.60 20 0 IOL - Low-Level Output Current - mA Figure 3. -0.2 -0.3 -0.4 -0.5 IOH - High-Level Output Current - mA Figure 4. TPS3110K33 HIGH-LEVEL OUTPUT VOLTAGE vs HIGH-LEVEL OUTPUT CURRENT MINIMUM PULSE DURATION AT VDD vs THRESHOLD OVERDRIVE VOLTAGE 3.4 50 VDD = 3.3 V SENSE = VDD MR = VDD WDI : Triggered 3.2 tW - Minimum Pulse Duration at VDD - ms VOH - High-Level output Voltage - V -0.1 TA = -40°C 3.0 TA = -40°C 2.8 TA = 0°C 2.6 TA = 25°C 2.4 TA = 85°C 2.2 2.0 MR : Open SENSE = VDD 45 40 35 30 VDD = 3.3 V 25 20 15 10 VDD = 0.9 V 5 0 0 -5 -10 -15 -20 IOH - Low-Level Output Current - mA Figure 5. Copyright © 2001–2007, Texas Instruments Incorporated -25 0 0.1 0.2 0.3 0.4 0.5 VDD - Threshold Overdrive Voltage - V Figure 6. Submit Documentation Feedback 11 TPS3103xxx TPS3106xxx TPS3110xxx www.ti.com SLVS363E – AUGUST 2001 – REVISED SEPTEMBER 2007 TYPICAL CHARACTERISTICS (continued) NORMALIZED THRESHOLD VOLTAGE vs FREE-AIR TEMPERATURE VIT - Normalized Threshold Voltage - V 1.008 1.006 1.004 1.002 1.000 0.998 0.996 0.994 0.992 -50 0 50 100 TA - Free-Air Temperature - °C Figure 7. 12 Submit Documentation Feedback Copyright © 2001–2007, Texas Instruments Incorporated TPS3103xxx TPS3106xxx TPS3110xxx www.ti.com SLVS363E – AUGUST 2001 – REVISED SEPTEMBER 2007 APPLICATION INFORMATION The TPS31xx family has a quiescent current in the 1-μA to 2-μA range. When RESET is active, triggered by the voltage monitored at VDD, the quiescent current increases to about 20 μA (see the Electrical Characteristics). In some applications it is necessary to minimize the quiescent current even during the reset period. This is especially true when the voltage of a battery is supervised and the RESET is used to shut down the system or for an early warning. In this case the reset condition will last for a longer period of time. The current drawn from the battery should almost be zero, especially when the battery is discharged. For this kind of application, either the TPS3103 or TPS3106 is a good fit. To minimize current consumption, select a version where the threshold voltage is lower than the voltage monitored at VDD. The TPS3106 has two reset outputs. One output (RSTVDD) is triggered from the voltage monitored at VDD. The other output (RSTSENSE) is triggered from the voltage monitored at SENSE. In the application shown in Figure 8, the TPS3106E09 is used to monitor the input voltage of two NiCd or NiMH cells. The threshold voltage (V(TH) = 0.86 V) was chosen as low as possible to ensure that the supply voltage is always higher than the threshold voltage at VDD. The voltage of the battery is monitored using the SENSE input. The voltage divider was calculated to assert a reset using the RSTSENSE output at 2 × 0.8 V = 1.6 V. R1 + R2 ǒ Ǔ VTRIP *1 VIT(S) (1) where: VTRIP is the voltage of the battery at which a reset is asserted and VIT(S) is the threshold voltage at SENSE = 0.551 V. R1 was chosen for a resistor current in the 1-μA range. With VTRIP = 1.6 V: R1 ≡ 1.9 × R2 R1 = 820 kΩ, R2 = 430 kΩ VDD R1 TPS3106E09DBV R3 MR 2 Cell NiMH RSTVDD SENSE RSTSENSE R2 Reset Output GND Figure 8. Battery Monitoring with 3-μA Supply Current for Device and Resistor Divider Copyright © 2001–2007, Texas Instruments Incorporated Submit Documentation Feedback 13 TPS3103xxx TPS3106xxx TPS3110xxx SLVS363E – AUGUST 2001 – REVISED SEPTEMBER 2007 www.ti.com WATCHDOG The TPS3110 device integrates a watchdog timer that must be periodically triggered by a positive or negative transition of WDI. When the supervising system fails to retrigger the watchdog circuit within the time-out interval, RESET becomes active for the time period (tD). This event also reinitializes the watchdog timer. MANUAL RESET (MR) Many μC-based products require manual-reset capability, allowing an operator or logic circuitry to initiate a reset. Logic low at MR asserts reset. Reset remains asserted while MR is low and for a time period (tD) after MR returns high. The input has an internal 100-kΩ pull-up resistor, so it can be left open if it is unused. Connect a normally open momentary switch from MR to GND to create a manual reset function. External debounce is not required. If MR is driven from long cables or if the device is used in noisy environments, connecting a 0.1-μF capacitor from MR to GND provides additional noise immunity. If there is a possibility of transient or DC conditions causing MR to rise above VDD, a diode should be used to limit MR to a diode drop above VDD. PFI, PFO The TPS3103 has an integrated power-fail (PFI) comparator with a separate open-drain (PFO) output. The PFI and PFO can be used for low-battery detection, power-fail warning, or for monitoring a power supply other than the main supply, and has no effect on RESET. An additional comparator is provided to monitor voltages other than the nominal supply voltage. The power-fail input (PFI) will be compared with an internal voltage reference of 0.551 V. If the input voltage falls below the power-fail threshold (VIT – (S)), the power-fail output (PFO) goes low. If it goes above 0.551 V plus approximately 15-mV hysteresis, the output returns to high. By connecting two external resistors, it is possible to supervise any voltage above 0.551 V. The sum of both resistors should be approximately 1 MΩ, to minimize power consumption and to assure that the current into the PFI pin can be neglected, compared with the current through the resistor network. The tolerance of the external resistors should be not more than 1% to ensure minimal variation of sensed voltage. If the power-fail comparator is unused, connect PFI to GND and leave PFO unconnected. For proper operation of the PFI-comparator, the supply voltage (VDD) must be higher than 0.8 V. SENSE The voltage at the SENSE input is compared with a reference voltage of 0.551 V. If the voltage at SENSE falls below the sense-threshold (VIT − (S)), reset is asserted. On the TPS3106, a dedicated RSTSENSE output is available. On the TPS3110, the logic signal from SENSE is OR-wired with the logic signal from VDD or MR. An internal timer delays the return of the output to the inactive state, once the voltage at SENSE goes above 0.551 V plus about 15 mV of hysteresis. For proper operation of the SENSE-comparator, the supply voltage must be higher than 0.8 V. 14 Submit Documentation Feedback Copyright © 2001–2007, Texas Instruments Incorporated TPS3103xxx TPS3106xxx TPS3110xxx www.ti.com SLVS363E – AUGUST 2001 – REVISED SEPTEMBER 2007 2V VDD R1 (1) MSP430 Low-Power mC Px.x RESET TPS3103H20 MR RESET PFI R2 VDD (1) Analog Circuit Py.x PFO GND GND -2 V V(NEG_TH) = 0.551 V - R2 (VDD - 0.551 V) R1 (1) Resistor may be integrated in mC. Figure 9. TPS3103 Monitoring a Negative Voltage 3.3 V 1.5 V VCORE VDD V(CORE_TH) = 0.551 V x R1 + R2 R2 R1 TPS3110K33 MR RESET SENSE WDI R2 GND VIO DSP RESET Px.y GND GND Figure 10. TPS3110 in a DSP-System Monitoring Both Supply Voltages Copyright © 2001–2007, Texas Instruments Incorporated Submit Documentation Feedback 15 PACKAGE OPTION ADDENDUM www.ti.com 17-Aug-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) TBD Lead/ Ball Finish (3) Samples (Requires Login) SN0402002DBVR ACTIVE SOT-23 DBV 6 TPS3103E12DBVR ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3103E12DBVRG4 ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3103E12DBVT ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3103E12DBVTG4 ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3103E15DBVR ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3103E15DBVRG4 ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3103E15DBVT ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3103E15DBVTG4 ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3103H20DBVR ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3103H20DBVRG4 ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3103H20DBVT ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3103H20DBVTG4 ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3103K33DBVR ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3103K33DBVRG4 ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3103K33DBVT ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3103K33DBVTG4 ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Addendum-Page 1 Call TI MSL Peak Temp Call TI PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 17-Aug-2012 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp Samples (Requires Login) TPS3106E09DBVR ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3106E09DBVRG4 ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3106E09DBVT ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3106E09DBVTG4 ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3106E16DBVR ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3106E16DBVRG4 ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3106E16DBVT ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3106E16DBVTG4 ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3106K33DBVR ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3106K33DBVRG4 ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3106K33DBVT ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3106K33DBVTG4 ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3110E09DBVR ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3110E09DBVRG4 ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3110E09DBVT ACTIVE SOT-23 DBV 6 TBD Call TI Call TI TPS3110E09DBVTG4 ACTIVE SOT-23 DBV 6 TBD Call TI Call TI TPS3110E12DBVR ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3110E12DBVRG4 ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3110E12DBVT ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Addendum-Page 2 (3) PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 17-Aug-2012 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp TPS3110E12DBVTG4 ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3110E15DBVR ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3110E15DBVRG4 ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3110E15DBVT ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3110E15DBVTG4 ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3110K33DBVR ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3110K33DBVRG4 ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3110K33DBVT ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS3110K33DBVTG4 ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM (3) Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Addendum-Page 3 PACKAGE OPTION ADDENDUM www.ti.com 17-Aug-2012 Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 4 PACKAGE MATERIALS INFORMATION www.ti.com 17-Aug-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) TPS3103E12DBVR SOT-23 DBV 6 3000 179.0 8.4 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 3.2 3.2 1.4 4.0 8.0 Q3 TPS3103E12DBVT SOT-23 DBV 6 250 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 TPS3103E15DBVR SOT-23 DBV 6 3000 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 TPS3103E15DBVT SOT-23 DBV 6 250 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 TPS3103H20DBVR SOT-23 DBV 6 3000 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 TPS3103H20DBVT SOT-23 DBV 6 250 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 TPS3103K33DBVR SOT-23 DBV 6 3000 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 TPS3103K33DBVR SOT-23 DBV 6 3000 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 TPS3103K33DBVT SOT-23 DBV 6 250 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 TPS3103K33DBVT SOT-23 DBV 6 250 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 TPS3106E09DBVR SOT-23 DBV 6 3000 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 TPS3106E09DBVT SOT-23 DBV 6 250 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 TPS3106E16DBVR SOT-23 DBV 6 3000 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 TPS3106E16DBVT SOT-23 DBV 6 250 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 TPS3106K33DBVR SOT-23 DBV 6 3000 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3 TPS3106K33DBVT SOT-23 DBV 6 250 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3 TPS3110E09DBVR SOT-23 DBV 6 3000 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 TPS3110E12DBVR SOT-23 DBV 6 3000 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 17-Aug-2012 Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TPS3110E12DBVT SOT-23 DBV 6 250 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 TPS3110E15DBVR SOT-23 DBV 6 3000 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 TPS3110E15DBVT SOT-23 DBV 6 250 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 TPS3110K33DBVR SOT-23 DBV 6 3000 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 TPS3110K33DBVT SOT-23 DBV 6 250 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS3103E12DBVR SOT-23 DBV 6 3000 203.0 203.0 35.0 TPS3103E12DBVT SOT-23 DBV 6 250 203.0 203.0 35.0 TPS3103E15DBVR SOT-23 DBV 6 3000 203.0 203.0 35.0 TPS3103E15DBVT SOT-23 DBV 6 250 203.0 203.0 35.0 TPS3103H20DBVR SOT-23 DBV 6 3000 203.0 203.0 35.0 TPS3103H20DBVT SOT-23 DBV 6 250 203.0 203.0 35.0 TPS3103K33DBVR SOT-23 DBV 6 3000 182.0 182.0 20.0 TPS3103K33DBVR SOT-23 DBV 6 3000 203.0 203.0 35.0 TPS3103K33DBVT SOT-23 DBV 6 250 182.0 182.0 20.0 TPS3103K33DBVT SOT-23 DBV 6 250 203.0 203.0 35.0 TPS3106E09DBVR SOT-23 DBV 6 3000 182.0 182.0 20.0 TPS3106E09DBVT SOT-23 DBV 6 250 182.0 182.0 20.0 Pack Materials-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 17-Aug-2012 Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS3106E16DBVR SOT-23 DBV 6 3000 182.0 182.0 20.0 TPS3106E16DBVT SOT-23 DBV 6 250 182.0 182.0 20.0 TPS3106K33DBVR SOT-23 DBV 6 3000 180.0 180.0 18.0 TPS3106K33DBVT SOT-23 DBV 6 250 180.0 180.0 18.0 TPS3110E09DBVR SOT-23 DBV 6 3000 182.0 182.0 20.0 TPS3110E12DBVR SOT-23 DBV 6 3000 182.0 182.0 20.0 TPS3110E12DBVT SOT-23 DBV 6 250 182.0 182.0 20.0 TPS3110E15DBVR SOT-23 DBV 6 3000 182.0 182.0 20.0 TPS3110E15DBVT SOT-23 DBV 6 250 182.0 182.0 20.0 TPS3110K33DBVR SOT-23 DBV 6 3000 182.0 182.0 20.0 TPS3110K33DBVT SOT-23 DBV 6 250 182.0 182.0 20.0 Pack Materials-Page 3 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2012, Texas Instruments Incorporated