TI TLK2711AIRCPRG4

TLK2711A
www.ti.com.................................................................................................................................................. SLLS908A – JULY 2008 – REVISED SEPTEMBER 2009
1.6 TO 2.7 GBPS TRANSCEIVER
Check for Samples :TLK2711A
FEATURES
1
•
2
•
•
•
•
•
•
1.6 to 2.7 Gigabits Per Second (Gbps)
Serializer/Deserializer
Hot-Plug Protection
High-Performance 80-Pin BGA Microstar
Junior™ Package (GQE)
2.5-V Power Supply for Low Power Operation
Programmable Preemphasis Levels on Serial
Output
Interfaces to Backplane, Copper Cables, or
Optical Converters
On-Chip 8-bit/10-bit Encoding/Decoding,
Comma Detect
•
•
•
•
•
•
•
•
•
On-Chip PLL Provides Clock Synthesis From
Low-Speed Reference
Receiver Differential Input Thresholds 200 mV
Minimum
Low Power: < 500 mW
3 V Tolerance on Parallel Data Input Signals
16-Bit Parallel TTL Compatible Data Interface
Ideal for High-Speed Backplane Interconnect
and Point-to-Point Data Link
Industrial Temperature Range (–40°C to 85°C
RCP Package Only)
Loss of Signal (LOS) Detection
Integrated 50-Ω Termination Resistors on RX
DESCRIPTION
The TLK2711A is a member of the WizardLink transceiver family of multigigabit transceivers, intended for use in
ultrahigh-speed bidirectional point-to-point data transmission systems. The TLK2711A supports an effective serial
interface speed of 1.6 Gbps to 2.7 Gbps, providing up to 2.16 Gbps of data bandwidth.
The primary application of this chip is to provide very high-speed I/O data channels for point-to-point baseband
data transmission over controlled impedance media of approximately 50Ω. The transmission media can be
printed-circuit board, copper cables, or fiber-optic cable. The maximum rate and distance of data transfer is
dependent upon the attenuation characteristics of the media and the noise coupling to the environment.
This device can also be used to replace parallel data transmission architectures by providing a reduction in the
number of traces, connector terminals, and transmit/receive terminals. Parallel data loaded into the transmitter is
delivered to the receiver over a serial channel, which can be a coaxial copper cable, a controlled impedance
backplane, or an optical link. It is then reconstructed into its original parallel format. It offers significant power and
cost savings over parallel solutions, as well as scalability for higher data rates in the future.
The TLK2711A performs data conversion parallel-to-serial and serial-to-parallel. The clock extraction functions as
a physical layer interface device. The serial transceiver interface operates at a maximum speed of 2.7 Gbps. The
transmitter latches 16-bit parallel data at a rate based on the supplied reference clock (TXCLK). The 16-bit
parallel data is internally encoded into 20 bits using an 8-bit/10-bit (8b/10b) encoding format. The resulting 20-bit
word is then transmitted differentially at 20 times the reference clock (TXCLK) rate. The receiver section
performs the serial-to-parallel conversion on the input data, synchronizing the resulting 20-bit wide parallel data
to the recovered clock (RXCLK). It then decodes the 20-bit wide data using the 8-bit/10-bit decoding format
resulting in 16 bits of parallel data at the receive data terminals (RXD0-15). The outcome is an effective data
payload of 2 Gbps to 2.5 Gbps (16 bits data x the frequency).
The TLK2711A is provided in two packages options: a 80-pin ball grid array MicroStar Junior package and a
64-pin VQFP (RCP) package.
The TLK2711A provides an internal loopback capability for self-test purposes. Serial data from the serializer is
passed directly to the deserializer, providing the protocol device with a functional self-check of the physical
interface.
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Microstar Junior, PowerPAD are trademarks of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2008–2009, Texas Instruments Incorporated
TLK2711A
SLLS908A – JULY 2008 – REVISED SEPTEMBER 2009.................................................................................................................................................. www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
DESCRIPTION (CONTINUED)
The TLK2711A has a loss of signal (LOS) detection circuit for conditions where the incoming signal no longer
has a sufficient voltage amplitude to keep the clock recovery circuit in lock.
The TLK2711A allows users to implement redundant ports by connecting receive data bus terminals from two
TLK2711A devices together. Asserting the LCKREFN to a low state will cause the receive data bus terminals,
RXD[0:15], RXCLK, RKLSB, and RKMSB to go to a high-impedance state. This places the device in a
transmit-only mode since the receiver is not tracking the data.
The TLK2711A uses a 2.5-V supply. The I/O section is 3 V compatible. With the 2.5-V supply the chipset is very
power efficient, consuming less than 450 mW typically. The TLK2711A is characterized for operation from –40°C
to 85°C (RCP only).
The TLK2711A is designed to be hot-plug capable. An on-chip power-on reset circuit holds the RXCLK low and
goes to high impedance on the parallel side output signal terminals as well as TXP and TXN during power up.
2
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s) :TLK2711A
TLK2711A
www.ti.com.................................................................................................................................................. SLLS908A – JULY 2008 – REVISED SEPTEMBER 2009
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s) :TLK2711A
3
TLK2711A
SLLS908A – JULY 2008 – REVISED SEPTEMBER 2009.................................................................................................................................................. www.ti.com
BLOCK DIAGRAM
Figure 1. TLK2711A Block Diagram
4
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s) :TLK2711A
TLK2711A
www.ti.com.................................................................................................................................................. SLLS908A – JULY 2008 – REVISED SEPTEMBER 2009
TERMINAL FUNCTIONS
TERMINAL
NAME
ENABLE
GND
GNDA
LCKREFN
NO.
I/O
DESCRIPTION
I (1)
Device enable. When this terminal is held low, the device is placed in power-down mode.
Only the signal detect circuit on the serial receive pair is active. When asserted high while the
device is in power-down mode, the transceiver goes into power-on reset before beginning
normal operation.
GQE
RCP
A5
24
A1, J1, D3,
E3, F3, G3,
C4, D4, E4,
F4, G4, A9,
J9
5, 13, 18,
28, 33,
43
H4, H6
52, 58,
61
B5
25
I(1)
(2)
Loop enable. When LOOPEN is active high, the internal loop-back path is activated. The
transmitted serial data is directly routed internally to the inputs of the receiver. This provides a
self-test capability in conjunction with the protocol device. The TXP and TXN outputs are held
in a high-impedance state during the loop-back test. LOOPEN is held low during standard
operational state with external serial outputs and inputs active.
Digital logic ground. Provides a ground for the logic circuits and digital I/O buffers.
Analog ground. GNDA provides a ground reference for the high-speed analog circuits, RX
and TX.
Lock to reference. When LCKREFN is low, the receiver clock is frequency locked to TXCLK.
This places the device in a transmit only mode since the receiver is not tracking the data.
When LCKREFN is asserted low, the receive data bus terminals, RXD[0:15], RXCLK and
RKLSB, RKMSB are in a high-impedance state.
When LCKREFN is deasserted high, the receiver is locked to the received data stream.
LOOPEN
B6
21
I
PRE
J5
56
I(2)
Preemphasis control. Selects the amount of preemphasis to be added to the high speed serial
output drivers. Left low or unconnected, 5% preemphasis is added. Pulled high, 20%
preemphasis is added.
PRBSEN
A4
26
I(2)
PRBS test enable. When asserted high results of pseudo random bit stream (PRBS) tests can
be monitored on the RKLSB terminal. A high on RKLSB indicates that valid PRBS is being
received.
RKLSB
A3
29
O
K-Code indicator/PRBS test results. When RKLSB is asserted high, an 8-bit/10-bit K code
was received and is indicated by data bits RXD0–RXD7. When RKLSB is asserted low an
8-bit/10-bit D code is received and is presented on data bits RXD0–RXD7.
When PRBSEN is asserted high this pin is used to indicate status of the PRBS test results
(high = pass).
RKMSB
B3
RXCLK
E2
RX_CLK
(1)
(2)
30
41
O
O
K-code indicator. When RKMSB is asserted high an 8-bit/10-bit K code was received and is
indicated by data bits RXD8–RXD15. When RKMSB is asserted low an 8-bit/10-bit D code
was received and is presented on data bits RXD8–RXD15. If the differential signal on RXN
and RXP drops below 200 mV, then RXD [0:15], RKLSB, and RKMSB are all asserted high.
Recovered clock. Output clock that is synchronized to RXD [0..9], RKLSB, and RKMSB.
RXCLK is the recovered serial data rate clock divided by 20. RXCLK is held low during
power-on reset.
Internal 10k pullup
Internal 10k pulldown
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s) :TLK2711A
5
TLK2711A
SLLS908A – JULY 2008 – REVISED SEPTEMBER 2009.................................................................................................................................................. www.ti.com
TERMINAL FUNCTIONS (Continued)
TERMINAL
NAME
NO.
I/O
GQE
RCP
RXD0
RXD1
RXD2
RXD3
RXD4
RXD5
RXD6
RXD7
RXD8
RXD9
RXD10
RXD11
RXD12
RXD13
RXD14
RXD15
H3
J2
H2
H1
G2
G1
F2
F1
E1
D1
C1
D2
C2
B1
B2
A2
51
50
49
47
46
45
44
42
40
39
37
36
35
34
32
31
RXN
RXP
J3
J4
DINRXN
DINRXP
53
54
O
I
DESCRIPTION
Receive data bus. These outputs carry 16-bit parallel data output from the transceiver to the
protocol device, synchronized to RXCLK. The data is valid on the rising edge of RXCLK as shown
in Figure 5. These terminals are in high-impedance state during power-on reset.
Serial receive inputs. RXP and RXN together are the differential serial input interface from a copper
or an optical I/F module.
TESTEN
B4
27
I (1)
Test mode enable. This terminal should be left unconnected or tied low.
TKLSB
A6
22
I (2)
K-code generator (LSB). When TKLSB is high, an 8-bit/10-bit K code is transmitted as controlled by
data bits TXD0–TXD7. When TKLSB is low an 8-bit/10-bit D code is transmitted as controlled by
data bits TXD0–TXD7.
TKMSB
B7
20
I(1)
K-code generator (MSB). When TKMSB is high an 8-bit/10-bit K code is transmitted as controlled by
data bits TXD8–TXD15. When TKMSB is low an 8-bit/10-bit D code is transmitted as controlled by
data bits TXD8–TXD15.
TXCLK
E9
8
I
62
63
64
2
3
4
6
7
10
11
12
14
15
16
17
19
I
GTX_CLK
TXD0
TXD1
TXD2
TXD3
TXD4
TXD5
TXD6
TXD7
TXD8
TXD9
TXD10
TXD11
TXD12
TXD13
TXD14
TXD15
H7
J8
H8
H9
G8
G9
F9
F8
D9
D8
C9
C8
B9
B8
A8
A7
TXN
TXP
J6
J7
DOUTTXN
DOUTTXP
(1)
(2)
6
59
60
O
Reference clock. TXCLK is a continuous external input clock that synchronizes the transmitter
interface signals TKMSB, TKLSB and TXD [0..15]. The frequency range of TXCLK is 80 MHz to 135
MHz. The transmitter uses the rising edge of this clock to register the 16-bit input data TXD [0..15]
for serialization.
Transmit data bus. These inputs carry the 16-bit parallel data output from a protocol device to the
transceiver for encoding, serialization, and transmission. This 16-bit parallel data clocked into the
transceiver on the rising edge of TXCLK as shown in Figure 2.
Serial transmit outputs. TXP and TXN are differential serial outputs that interface to copper or an
optical I/F module. These terminals transmit NRZ data at a rate of 20 times the TXCLK value. TXP
and TXN are put in a high-impedance state when LOOPEN is high and are active when LOOPEN is
low. During power-on reset these terminals are high impedance.
Internal 10k pulldown
Internal 10k pullup
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s) :TLK2711A
TLK2711A
www.ti.com.................................................................................................................................................. SLLS908A – JULY 2008 – REVISED SEPTEMBER 2009
TERMINAL FUNCTIONS (Continued)
TERMINAL
NAME
VDD
VDDA
NO.
I/O
GQE
RCP
C5, D5, E5, F5, G5,
C6, D6, E6, F6, G6,
C7, D7, E7, F7, G7,
E8
1, 9, 23,
38, 48
H5
55, 57
DESCRIPTION
Digital logic power. Provides power for all digital circuitry and digital I/O buffers.
Analog power. VDDA provides a supply reference for the high-speed analog circuits,
receiver and transmitter.
DETAILED DESCRIPTION
TRANSMIT INTERFACE
The transmitter portion registers valid incoming 16-bit wide data (TXD[0:15]) on the rising edge of the TXCLK.
The data is then 8-bit/10-bit encoded, serialized, and transmitted sequentially over the differential high-speed I/O
channel. The clock multiplier multiplies the reference clock (TXCLK) by a factor of 10 times, creating a bit clock.
This internal bit clock is fed to the parallel-to-serial shift register which transmits data on both the rising and
falling edges of the bit clock, providing a serial data rate that is 20 times the reference clock. Data is transmitted
LSB (TXD0) first.
transmit data bus
The transmit bus interface accepts 16-bit single-ended TTL parallel data at the TXD[0:15] terminals. Data and
K-code control is valid on the rising edge of the TXCLK. The TXCLK is used as the word clock. The data,
K-code, and clock signals must be properly aligned as shown in Figure 2. Detailed timing information can be
found in the electrical characteristics table.
Figure 2. Transmit Timing Waveform
Transmission Latency
The data transmission latency of the TLK2711A is defined as the delay from the initial 16-bit word load to the
serial transmission of bit 0. The transmit latency is fixed once the link is established. However, due to silicon
process variations and implementation variables such as supply voltage and temperature, the exact delay varies
slightly. The minimum transmit latency td(Tx latency) is 34 bit times; the maximum is 38 bit times. Figure 3 illustrates
the timing relationship between the transmit data bus, the TXCLK, and the serial transmit terminals.
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s) :TLK2711A
7
TLK2711A
SLLS908A – JULY 2008 – REVISED SEPTEMBER 2009.................................................................................................................................................. www.ti.com
Figure 3. Transmission Latency
8-Bit/10-Bit Encoder
All true serial interfaces require a method of encoding to insure minimum transition density so that the receiving
PLL has a minimal number of transitions to stay locked on. The encoding scheme maintains the signal dc
balance by keeping the number of ones and zeros the same. This provides good transition density for clock
recovery and improves error checking. The TLK2711A uses the 8-bit/10-bit encoding algorithm that is used by
fibre channel and gigabit ethernet. This is transparent to the user, as the TLK2711A internally encodes and
decodes the data such that the user reads and writes actual 16-bit data.
The 8-bit/10-bit encoder converts 8-bit wide data to a 10-bit wide encoded data character to improve its
transmission characteristics. Since the TLK2711A is a 16-bit wide interface, the data is split into two 8-bit wide
bytes for encoding. Each byte is fed into a separate encoder. The encoding is dependent upon two additional
input signals, the TKMSB and TKLSB.
Table 1. Transmit Data Controls
TKLSB
TKMSB
0
0
Valid data on TXD(0–7),
16 BIT PARALLEL INPUT
Valid data TXD(8–15)
0
1
Valid data on TXD(0–7),
K code on TXD(8–15))
1
0
K code on TXD(0–7),
Valid data on TXD(8–15)
1
1
K code on TXD(0–7),
K code on TXD(8–15)
PRBS Generator
The TLK2711A has a built-in 27-1 PRBS (pseudorandom bit stream) function. When the PRBSEN terminal is
forced high, the PRBS test is enabled. A PRBS is generated and fed into the 10-bit parallel-to-serial converter
input register. Data from the normal input source is ignored during the PRBS mode. The PRBS pattern is then
fed through the transmit circuitry as if it were normal data and sent out to the transmitter. The output can be sent
to a BERT (bit error rate tester), the receiver of another TLK2711A, or looped back to the receive input. Since the
PRBS is not really random but a predetermined sequence of ones and zeroes, the data can be captured and
checked for errors by a BERT.
Parallel-to-Serial
The parallel-to-serial shift register takes in the 20-bit wide data word multiplexed from the two parallel 8-bit/10-bit
encoders and converts it to a serial stream. The shift register is clocked on both the rising and falling edge of the
internally generated bit clock, which is 10 times the TXCLK input frequency. The LSB (TXD0) is transmitted first.
8
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s) :TLK2711A
TLK2711A
www.ti.com.................................................................................................................................................. SLLS908A – JULY 2008 – REVISED SEPTEMBER 2009
High-Speed Data Output
The high-speed data output driver consists of a voltage mode logic (VML) differential pair optimized for a 50-Ω
impedance environment. The magnitude of the differential pair signal swing is compatible with pseudo emitter
coupled logic (PECL) levels when ac-coupled. The line can be directly-coupled or ac-coupled. Refer to Figure 11
and Figure 12 for termination details. The outputs also provide preemphasis to compensate for ac loss when
driving a cable or PCB backplane trace over a long distance (see Figure 4). The level of pre-emphasis is
controlled by PRE as shown in Table 2.
Table 2. Programmable Pre-emphasis
PRE
(1)
Figure 4. Output Voltage Under Pre-emphasis
(|VTXP–VTXN|)
PRE-EMPHASIS LEVEL(%)
VOD(P), VOD(D) (1)
0
5%
1
20%
VOD(p): Voltage swing when there is a transition in the data
stream.
VOD(d): Voltage swing when there is no transition in the data
stream.
Receive Interface
The receiver portion of the TLK2711A accepts 8-bit/10-bit encoded differential serial data. The interpolator and
clock recovery circuit locks to the data stream and extract the bit rate clock. This recovered clock is used to
retime the input data stream. The serial data is then aligned to two separate 10-bit word boundaries, 8-bit/10-bit
decoded and output on a 16-bit wide parallel bus synchronized to the extracted receive clock. The data is
received LSB (RXD0) first.
Receive Data Bus
The receive bus interface drives 16-bit wide single-ended TTL parallel data at the RXD[0:15] terminals. Data is
valid on the rising edge of the RXCLK. The RXCLK is used as the recovered word clock. The data, RKLSB,
RKMSB, and clock signals are aligned as shown in Figure 5. Detailed timing information can be found in the
switching characteristics table.
Figure 5. Receive Timing Waveform
Data Reception Latency
The serial-to-parallel data receive latency is the time from when the first bit arrives at the receiver until it is output
in the aligned parallel word. The receive latency is fixed once the link is established. However, due to silicon
process variations and implementation variables such as supply voltage and temperature, the exact delay varies
slightly. The minimum receive latency td(Rx latency) is 76 bit times; the maximum is 107 bit times. Figure 6 illustrates
the timing relationship between the serial receive terminals, the recovered word clock (RXCLK), and the receive
data bus.
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s) :TLK2711A
9
TLK2711A
SLLS908A – JULY 2008 – REVISED SEPTEMBER 2009.................................................................................................................................................. www.ti.com
Figure 6. Receiver Latency
Serial-to-Parallel
Serial data is received on the RXP and RXN terminals. The interpolator and clock recovery circuit locks to the
data stream if the clock to be recovered is within 200 PPM of the internally generated bit rate clock. The
recovered clock is used to retime the input data stream. The serial data is then clocked into the serial-to-parallel
shift registers. The 10-bit wide parallel data is then multiplexed and fed into two separate 8-bit/10-bit decoders
where the data is then synchronized to the incoming data stream word boundary by detection of the comma
8-bit/10-bit synchronization pattern.
Common Detect and 8-Bit/10-Bit Decoding
The TLK2711A has two parallel 8-bit/10-bit decode circuits. Each 8-bit/10-bit decoder converts 10 bit encoded
data (half of the 20-bit received word) back into 8 bits. The comma detect circuit is designed to provide for byte
synchronization to an 8-bit/10-bit transmission code. When parallel data is clocked into a parallel to serial
converter, the byte boundary that was associated with the parallel data is now lost in the serialization of the data.
When the serial data is received and converted to parallel format again, a method is needed to recognize the
byte boundary. Generally this is accomplished through the use of a synchronization pattern. This is generally a
unique pattern of 1's and 0's that either cannot occur as part of valid data or is a pattern that repeats at defined
intervals. The 8-bit/10-bit encoding contains a character called the comma (b0011111 or b1100000), which is
used by the comma detect circuit on the TLK2711A to align the received serial data back to its original byte
boundary. The decoder detects the comma, generating a synchronization signal aligning the data to their 10-bit
boundaries for decoding; the comma is mapped into the LSB. The decoder then converts the data back into 8-bit
data. The output from the two decoders is latched into the 16-bit register synchronized to the recovered parallel
data clock (RXCLK) and output valid on the rising edge of the RXCLK.
NOTE
The TLK2711A only achieves byte alignment on the 0011111 comma.
Decoding provides two additional status signals, RKLSB and RKMSB. When RKLSB is asserted , an 8-bit/10-bit
K code was received and the specific K code is presented on the data bits RXD0–RXD7; otherwise, an
8-bit/10-bit D code was received. When RKMSB is asserted, an 8-bit/10-bit K code was received and the specific
K-code is presented on data bits RXD8–RXD15; otherwise, an 8-bit/10-bit D code was received (see Table 3).
The valid K codes the TLK2711A decodes are provided in Table 4. An error detected on either byte, including K
codes not in Table 4, causes that byte only to indicate a K0.0 code on the RK×SB and associated data pins,
where K0.0 is known to be an invalid 8-bit/10-bit code. A loss of input signal causes a K31.7 code to be
presented on both bytes, where K31.7 is also known to be an invalid 8-bit/10-bit code.
10
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s) :TLK2711A
TLK2711A
www.ti.com.................................................................................................................................................. SLLS908A – JULY 2008 – REVISED SEPTEMBER 2009
Table 3. Receive Status Signals
RKLSB
RKMSB
0
0
Valid data on RXD(0–7),
DECODED 20 BIT OUTPUT
Valid data RXD(8–15)
0
1
Valid data on RXD(0–7),
K code on RXD(8–15))
1
0
K code on RXD(0–7),
Valid data on RXD(8–15)
1
1
K code on RXD(0–7),
K code on RXD(8–15)
Table 4. Valid K Characters
(1)
K CHARACTER
RECEIVE DATA BUS
(RXD[7–0]) OR (RXD[15–8])
K28.0
000 11100
K28.1 (1)
001 11100
K28.2
010 11100
K28.3
011 11100
K28.4
100 11100
K28.5(1)
101 11100
K28.6
110 11100
K28.7(1)
111 11100
K23.7
111 10111
K27.7
111 11011
K29.7
111 11101
K30.7
111 11110
Should only be present on RXD[7-0] when in running disparity < 0.
Power Down Mode
When the ENABLE pin is pulled low, the TLK2711A goes into power-down mode. In the power-down mode, the
serial transmit pins (TXN), the receive data bus pins (RXD[0:15]), and RKLSB goes into a high-impedance state.
In the power-down condition, the signal detection circuit draws less than 15 mW. When the TLK2711A is in the
power-down mode, the clock signal on the TXCLK terminal must be provided.
Loss of Signal Detection
The TLK2711A has a loss of signal detection circuit for conditions where the incoming signal no longer has a
sufficient voltage level to keep the clock recovery circuit in lock. The signal detection circuit is intended to be an
indication of gross signal error conditions, such as a detached cable or no signal being transmitted, and not an
indication of signal coding health. The TLK2711A reports this condition by asserting RKLSB, RKMSB and
RXD[0:15] terminals to a high state. As long as the differential signal is above 200 mV in differential magnitude,
the LOS circuit does not signal an error condition.
PRBS Verification
The TLK2711A also has a built-in BERT function in the receiver side that is enabled by the PRBSEN. It can
check for errors and report the errors by forcing the RKLSB terminal low.
Reference Clock Input
The reference clock (TXCLK) is an external input clock that synchronizes the transmitter interface. The reference
clock is then multiplied in frequency 10 times to produce the internal serialization bit clock. The internal
serialization bit clock is frequency-locked to the reference clock and used to clock out the serial transmit data on
both its rising and falling edges, providing a serial data rate that is 20 times the reference clock.
Operating Frequency Range
The TLK2711A can operate at a serial data rate from 1.6 Gbps to 2.7 Gbps. To achieve these serial rates,
TXCLK must be within 80 MHz to 135 MHz. The TXCLK must be within ±100 PPM of the desired parallel data
rate clock.
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s) :TLK2711A
11
TLK2711A
SLLS908A – JULY 2008 – REVISED SEPTEMBER 2009.................................................................................................................................................. www.ti.com
Testability
The TLK2711A has a comprehensive suite of built-in self-tests. The loopback function provides for at-speed
testing of the transmit/receive portions of the circuitry. The enable terminal allows for all circuitry to be disabled
so that a quiescent current test can be performed. The PRBS function allows for BIST (built-in self-test).
Loopback Testing
The transceiver can provide a self-test function by enabling (LOOPEN) the internal loop-back path. Enabling this
terminal causes serial-transmitted data to be routed internally to the receiver. The parallel data output can be
compared to the parallel input data for functional verification. (The external differential output is held in a
high-impedance state during the loopback testing.)
Built-In Self-Test (BIST)
The TLK2711A has a BIST function. By combining PRBS with loopback, an effective self-test of all the circuitry
running at full speed can be realized. The successful completion of the BIST is reported on the RKLSB terminal.
Power-On Reset
Upon application of minimum valid power, the TLK2711A generates a power-on reset. During the power-on reset
the RXD[0..15], RKLSB, and RKMSB signal terminals go to a high-impedance state. The RXCLK is held low. The
length of the power-on reset cycle is dependent upon the TXCLK frequency, but is less than 1 ms.
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature (unless otherwise noted) (1)
VDD
Supply voltage
(2)
Voltage range at TXD[0..15], ENABLE, TXCLK, TKMSB, TKLSB, LOOPEN,
PRBSEN, LCKREFN, PRE
Voltage range at any other terminal except above
PD
Package power dissipation
Tstg
Storage temperature
Electrostatic discharge
TA
Characterized free-air operating
temperature range
(2)
UNIT
–0.3 to 3
V
–0.3 to 4
V
–0.3 to VDD+0.3
V
See Dissipation Rating Table
–65 to 150
°C
4
kV
CDM
1.5
kV
RCP
–40 to 85
°C
GQE
0 to 70
°C
260
°C
HBM
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds
(1)
VALUE
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values, except differential I/O bus voltages, are stated with respect to network ground.
DISSIPATION RATINGS (1)
(1)
PACKAGE
θJA
(°C/W)
θJC
(°C/W)
TA = 25°C
POWER RATING
GQE
37.8
4.56
3.3 W
This data was taken using 2-oz trace and copper pad that is soldered directly to the JEDEC standard
4-layer, 3-inch x 3-inch PCB.
DISSIPATION RATINGS
(1)
(2)
12
PACKAGE
TA ≤ 25°C
POWER RATING
RCP64 (2)
5.25 W
DERATING FACTOR
ABOVE TA = 25°C
(1)
TA = 70°C
POWER RATING
46.58 mW/°C
2.89 W
This is the inverse of the traditional junction-to-ambient thermal resistance (RθJA).
2 oz. Trace and copper pad with solder.
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s) :TLK2711A
TLK2711A
www.ti.com.................................................................................................................................................. SLLS908A – JULY 2008 – REVISED SEPTEMBER 2009
DISSIPATION RATINGS (continued)
(3)
(4)
(1)
PACKAGE
TA ≤ 25°C
POWER RATING
RCP64 (3)
3.17 W
23.70 mW/°C
1.74 W
RCP64 (4)
2.01 W
13.19 mW/°C
1.11 W
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
2 oz. Trace and copper pad without solder.
Standard JEDEC High-K board.
For more information, refer to TI application note PowerPAD™ Thermally Enhanced package, TI literature
number SLMA002.
ELECTRICAL CHARACTERISTICS
over recommended operating conditions
PARAMETER
VDD
TEST CONDITIONS
MIN
Supply voltage
ICC
Supply current
PD
Power dissipation
2.3
NOM
MAX
2.5
2.7
Frequency = 1.6 Gbps, PRBS pattern
105
Frequency = 2.7 Gbps, PRBS pattern
156
Frequency = 1.6 Gbps, PRBS pattern
262
Frequency = 2.7 Gbps, PRBS pattern
390
Frequency = 2.7 Gbps, worst case pattern (1)
(1)
V
mA
mW
550
Shutdown current
Enable = 0, VDDA, VDD terminals, VDD = MAX
PLL startup lock time
VDD, VDDC = 2.3 V
3
0.1
Data acquisition time
TA
UNIT
mA
0.4
ms
1024
Operating free-air temperature
Bits
–40
85
°C
Worst case pattern is a pattern that creates a maximum transition density on the serial transceiver.
REFERENCE CLOCK (TXCLK)TIMING REQUIREMENTS
over recommended operating conditions (unless otherwise noted)
MIN
TYP
MAX
UNIT
Frequency
PARAMETER
Minimum data rate
TEST CONDITIONS
Typ–0.01%
80
Typ+0.01%
MHz
Frequency
Maximum data rate
Typ–0.01%
135
Typ+0.01%
MHz
100
ppm
Frequency tolerance
–100
Duty cycle
40%
Jitter
50%
60%
Peak-to-peak
40
ps
TTL INPUT ELECTRICAL CHARACTERISTICS
over recommended operating conditions (unless otherwise noted), TTL signals: TXDO–TXD15, TXCLK, LOOPEN,
LCKREFN, ENABLE, PRBS_EN, TKLSB, TKMSB, PRE
PARAMETER
TEST CONDITIONS
MIN
TYP
1.7
MAX
UNIT
VIH
High-level input voltage
See Figure 7
3.6
VIL
Low-level input voltage
See Figure 7
IIH
Input high current
VDD = MAX, VIN = 2 V
IIL
Input low current
VDD = MAX, VIN = 0.4 V
CI
Receiver input capacitance
tr
Rise time, TXCLK, TKMSB, TKLSB, TXD[0..15]
0.7 V to 1.9 V, C = 5 pF, See Figure 7
1
ns
tf
Fall time, TXCLK, TKMSB, TKLSB, TXD[0..15]
1.9 V to 0.7 V, C = 5 pF, See Figure 7
1
ns
tsu
TXD[0..15], TKMSB, TKLSB setup to ↑ TXCLK
See Figure 7
1.5
ns
th
TXD, TKMSB, TKLSB hold to ↑ TXCLK
See Figure 7
0.4
ns
0.80
V
40
μA
μA
–40
4
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s) :TLK2711A
V
pF
13
TLK2711A
SLLS908A – JULY 2008 – REVISED SEPTEMBER 2009.................................................................................................................................................. www.ti.com
Figure 7. TTL Data Input Valid Levels for AC Measurements
14
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s) :TLK2711A
TLK2711A
www.ti.com.................................................................................................................................................. SLLS908A – JULY 2008 – REVISED SEPTEMBER 2009
TTL OUTPUT SWITCHING CHARACTERISTICS
over recommended operating conditions (unless otherwise noted)
MIN
TYP
VOH
High-level output voltage
PARAMETER
IOH = –1 mA, VDD = MIN
2.10
2.3
VOL
Low-level output voltage
IOL = 1 mA, VDD = MIN
GND
0.25
tr(slew)
Slew rate (rising), magnitude of RXCLK,
RKLSB, RKMSB, RXD[0..15]
0.8 V to 2 V, C = 5 pF, See Figure 8
0.5
V/ns
tf(slew)
Slew rate (falling), magnitude of RXCLK,
RKLSB, RKMSB, RXD[0..15]
0.8 V to 2 V, C = 5 pF, See Figure 8
0.5
V/ns
tsu
RXD[0 15] RKMSB RKLSB setup to ↑ RXCLK
tsu 0..15], RKMSB,
th
TEST CONDITIONS
RXD[0 15] RKMSB RKLSB hold to ↑ RXCLK
50% voltage swing, TXCLK = 80 MHz,
See Figure 8
50% voltage swing, TXCLK = 135 MHz,
See Figure 8
50% voltage swing, TXCLK = 80 MHz,
See Figure 8
50% voltage swing, TXCLK = 135 MHz,
See Figure 8
MAX
UNIT
V
0.5
V
3
2.5
ns
3
2.5
ns
Figure 8. TTL Data Output Valid Levels for AC Measurements
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s) :TLK2711A
15
TLK2711A
SLLS908A – JULY 2008 – REVISED SEPTEMBER 2009.................................................................................................................................................. www.ti.com
TRANSMITTER/RECEIVER CHARACTERISTICS
PARAMETER
MIN
NOM
MAX
Rt = 50Ω, PREM = high, dc-coupled, See
Figure 9
TEST CONDITIONS
655
725
795
Rt = 50Ω, PREM = low, dc-coupled, See
Figure 9
590
650
710
1310
1450
1590
1180
1300
1420
540
600
660
mV
1080
1200
1320
mVPP
1000
1250
1400
mV
1600
mV
VOD(p)
Preemphasis VOD, direct,
VOD(p) = |VTXP – VTXN|
VOD(
Rt = 50Ω, PREM = high, dc-coupled, See
Differential peak-to-peak output voltage Figure 9
with preemphasis
Rt = 50Ω, PREM = low, dc-coupled, See
Figure 9
pp_p)
VOD(d)
Deemphais output voltage,
|VTXP–VTXN|
Rt = 50 Ω, DC-coupled, See Figure 9
VOD(pp_d)
Differential, peak-to-peak output
voltage with deemphasis
Rt = 50Ω, dc-coupled, See Figure 9
V(cmt)
Transmit common mode voltage range, Rt = 50Ω, See Figure 9
(VTXP + VTXN)/2
VID
Receiver input voltage differential,
|VRXP – VRXN|
V(cmr)
Receiver common mode voltage range,
(VRXP + VRXN)/2
Ilkg
Receiver input leakage current
200
1000
1250
–10
Ci Receiver input capacitance
Differential output jitter at 2.7 Gbps, Random
+ deterministic, PRBS pattern
0.20
Differential output jitter at 1.5 Gbps, Random
+ deterministic, PRBS pattern
0.16
Differential output signal rise, fall time
(20% to 80%)
RL = 50Ω, CL = 5 pF, See Figure 9
150
Jitter tolerance
Differential input jitter, random +
deterministic, PRBS pattern at zero crossing
Serial data total jitter (peak-to-peak)
tt, tf
2250
UNIT
mV
mVPP
mV
10
μA
2
pF
UI (1)
ps
0.60
UI
td(Tx
latency)
Tx latency
See Figure 3
34
38
bits
td(Rx
latency)
Rx latency
See Figure 6
76
107
bits
(1)
UI is the time interval of one serialized bit.
Figure 9. Differential and Common-Mode Output Voltage Definitions
16
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s) :TLK2711A
TLK2711A
www.ti.com.................................................................................................................................................. SLLS908A – JULY 2008 – REVISED SEPTEMBER 2009
THERMAL INFORMATION
THERMAL CHARACTERISTICS
PARAMETER
RθJA
RθJC
Junction-to-free-air
thermal resistance
Junction-to-case
thermal resistance
TEST CONDITIONS
MIN
TYP
Board-mounted, no air flow, high conductivity TI recommended test
board, chip soldered or greased to thermal land
21.47
Board-mounted, no air flow, high conductivity TI recommended test
board with thermal land but no solder or grease thermal connection to
thermal land
42.20
Board-mounted, no air flow, JEDEC test board
75.88
Board-mounted, no air flow, high conductivity TI recommended test
board, chip soldered or greased to thermal land
0.38
Board-mounted, no air flow, high conductivity TI recommended test
board with thermal land but no solder or grease thermal connection to
thermal land
0.38
Board-mounted, no air flow, JEDEC test board
MAX
UNIT
°C/W
°C/W
7.8
APPLICATION INFORMATION
Figure 10. External Component Interconnection
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s) :TLK2711A
17
TLK2711A
SLLS908A – JULY 2008 – REVISED SEPTEMBER 2009.................................................................................................................................................. www.ti.com
Figure 11. High-Speed I/O Directly-Coupled Mode
Figure 12. High-Speed I/O AC-Coupled Mode
18
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s) :TLK2711A
TLK2711A
www.ti.com.................................................................................................................................................. SLLS908A – JULY 2008 – REVISED SEPTEMBER 2009
Changes from Original (July 2008) to Revision A ........................................................................................................... Page
•
Changed invalid K-codes to correct typographical errors (Table 4) ................................................................................... 11
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s) :TLK2711A
19
PACKAGE OPTION ADDENDUM
www.ti.com
10-Sep-2009
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TLK2711AIRCP
ACTIVE
HVQFP
RCP
64
160
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
TLK2711AIRCPG4
ACTIVE
HVQFP
RCP
64
160
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
TLK2711AIRCPR
ACTIVE
HVQFP
RCP
64
1000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
TLK2711AIRCPRG4
ACTIVE
HVQFP
RCP
64
1000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
TLK2711AJRZQE
ACTIVE
BGA MI
CROSTA
R JUNI
OR
ZQE
80
360
SNAGCU
Level-3-260C-168 HR
Green (RoHS &
no Sb/Br)
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
TLK2711AIRCPR
Package Package Pins
Type Drawing
HVQFP
RCP
64
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
1000
330.0
24.4
Pack Materials-Page 1
13.0
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
13.0
1.5
16.0
24.0
Q2
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TLK2711AIRCPR
HVQFP
RCP
64
1000
367.0
367.0
45.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated